Milwaukee 1676-6 Manuel utilisateur

Marque: Milwaukee

Modèle: 1676-6

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE

MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL

DEL OPERADOR.

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

HEAVY-DUTY HOLE HAWG

FOREUSE EXTRA-ROBUSTE HOLE HAWG

TALADRO HEAVY-DUTY HOLE HAWG

Catalog No.

No de Cat.

Catálogo No.

1670-1

1675-1

1675-6

1676-6

WORK AREA SAFETY

ELECTRICAL SAFETY

PERSONAL SAFETY

WARNING

READ ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in electric shock, ﬁre and/or

serious injury. The term "power tool" in all of the warnings listed below refers to your

mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

GENERAL SAFETY RULES-FOR ALL BATTERY OPERATED TOOLS

1. Keep work area clean and well lit.

Cluttered or dark areas invite acci-

dents.

2. Do not operate power tools in ex-

plosive atmospheres, such as in the

presence of ﬂammable liquids, gases,

or dust. Power tools create sparks which

may ignite the dust or fumes.

3. Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

4. Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs

with earthed (grounded) power tools.

Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock

if your body is earthed or grounded.

Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric

shock.

7. Do not abuse the cord. Never use the

cord for carrying, pulling, or unplug-

ging the power tool. Keep cord away

from heat, oil, sharp edges, or mov-

ing parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool out-

doors, use an extension cord suitable

for outdoor use. Use of a cord suitable

for outdoor use reduces the risk of elec-

tric shock.

9. Stay alert, watch what you are do-

ing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the inﬂuence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may result

in serious personal injury.

10.

Use safety equipment. Always wear

eye protection. Safety equipment such

as dust mask, non-skid safety shoes,

hard hat, or hearing protection used

for appropriate conditions will reduce

personal injuries.

11.

Avoid accidental starting. Ensure the

switch is in the off-position before plug-

ging in. Carrying tools with your ﬁnger on

the switch or plugging in power tools that

have the switch on invites accidents.

12.

Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

13.

Do not overreach. Keep proper foot-

ing and balance at all times. This

enables better control of the power tool

in unexpected situations.

14. Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery, or long

hair can be caught in moving parts.

15. If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of these de-

vices can reduce dust-related hazards.

POWER TOOL USE AND CARE

16. Do not force the power tool. Use the

correct power tool for your applica-

tion. The correct power tool will do the

job better and safer at the rate for which

it was designed.

17. Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

18. Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preven-

tive safety measures reduce the risk of

starting the tool accidentally.

19. Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tools or

these instructions to operate power

tools. Power tools are dangerous in the

hands of untrained users.

20. Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any

other condition that may affect the

power tool's operation. If damaged,

have the power tool repaired before

use. Many accidents are caused by

poorly maintained power tools.

21. Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

22. Use the power tool, accessories and

tool bits etc., in accordance with

these instructions and in the manner

intended for the particular type of

power tool, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

SERVICE

23. Have your power tool serviced by a

qualiﬁed repair person using only

identical replacement parts. This will

ensure that the safety of the power tool

is maintained.

SPECIFIC SAFETY RULES

1. Use auxiliary handles supplied with

the tool. Loss of control can cause

personal injury.

2. Wear ear protectors with impact

drills. Exposure to noise can cause

hearing loss.

Hold power tools by insulated grip-

ping surfaces when performing an

operation where the cutting tool may

contact hidden wiring or its own cord.

Contact with a “live” wire will make ex-

posed metal parts of the tool “live” and

shock the operator.

4 Maintain labels and nameplates.

These carry important information.

If unreadable or missing, contact a

MILWAUKEE service facility for a free

replacement.

5. WARNING! Some dust created by

power sanding, sawing, grinding, drill-

ing, and other construction activities

contains chemicals known to cause

cancer, birth defects or other reproduc-

tive harm. Some examples of these

chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement

and other masonry products, and

• arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this

type of work. To reduce your exposure

to these chemicals: work in a well ven-

tilated area, and work with approved

safety equipment, such as those dust

masks that are speciﬁcally designed to

ﬁlter out microscopic particles.

The grounding prong in the plug is connected

through the green wire inside the cord to

the grounding system in the tool. The green

wire in the cord must be the only wire con-

nected to the tool's grounding system and

must never be attached to an electrically

“live” terminal.

Your tool must be plugged into an appropri-

ate outlet, properly installed and grounded in

accordance with all codes and ordinances.

The plug and outlet should look like those

in Figure A.

Double Insulated Tools:

Tools with Two Prong Plugs

Tools marked “Double Insulated” do not

require grounding. They have a special

double insulation system which satisfies

OSHA requirements and complies with

the applicable standards of Underwriters

Laboratories, Inc., the Canadian Standard

Association and the National Electrical

Code. Double Insulated tools may be used

in either of the 120 volt outlets shown in

Figures B and C.

Grounded Tools:

Tools with Three Prong Plugs

Tools marked “Grounding Required” have a

three wire cord and three prong grounding

plug. The plug must be connected to a prop-

erly grounded outlet (See Figure A). If the

tool should electrically malfunction or break

down, grounding provides a low resistance

path to carry electricity away from the user,

reducing the risk of electric shock.

Fig. B

Fig. C

Fig. A

Improperly connecting the grounding

wire can result in the risk of electric

shock. Check with a qualiﬁed electri-

cian if you are in doubt as to whether

the outlet is properly grounded. Do

not modify the plug provided with

the tool. Never remove the grounding

prong from the plug. Do not use the

tool if the cord or plug is damaged.

If damaged, have it repaired by a

MILWAUKEE service facility before

use. If the plug will not ﬁt the outlet,

have a proper outlet installed by a

qualiﬁed electrician.

GROUNDING

WARNING

FUNCTIONAL DESCRIPTION

1. Spade Handle

2. Chuck

3. Trigger Switch

4. Reversing Switch

5. Switch Handle

6. Motor Housing

7. Gear Shift Lever

8. Pipe Handle

9. Insulated Gripping Surfaces

Amperes

Symbology

Canadian Standards

Association

Underwriters

Laboratories, Inc.

Volts Alternating Current

No Load Revolutions

per Minute (RPM)

Mexican Approvals Marking

Wood

Capacity

WithShip

Auger Bit

1-1/2"

1-1/4"

1-1/2"

1-1/4"

1-1/2"

1-1/4"

1-1/2"

With

Selfeed Bit

2-9/16"

1-3/8"

4-5/8"

1-3/8"

4-5/8"

1-3/8"

4-5/8"

Volts

120

Speed

High

Low

High

Low

High

Low

No Load

RPM

900

1200

300

1200

300

1200

300

With

Twist Bit

7/16"

5/16"

1/2"

5/16"

1/2"

5/16"

1/2"

With Auger

Bit

1-1/2"

1-1/8"

1-1/2"

1-1/8"

1-1/2"

1-1/8"

1-1/2"

Steel

Speciﬁcations

Cat. No.

1670-1

1675-1

1675-6

1676-6

Grounded tools require a three wire exten-

sion cord. Double insulated tools can use

either a two or three wire extension cord.

As the distance from the supply outlet

increases, you must use a heavier gauge

extension cord. Using extension cords with

inadequately sized wire causes a serious

drop in voltage, resulting in loss of power

and possible tool damage. Refer to the table

shown to determine the required minimum

wire size.

The smaller the gauge number of the wire,

the greater the capacity of the cord. For ex-

ample, a 14 gauge cord can carry a higher

current than a 16 gauge cord. When using

more than one extension cord to make up

the total length, be sure each cord contains

at least the minimum wire size required. If

you are using one extension cord for more

than one tool, add the nameplate amperes

and use the sum to determine the required

minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord out

doors, be sure it is marked with the sufﬁx

“W-A” (“W” in Canada) to indicate that it

is acceptable for outdoor use.

• Be sure your extension cord is prop-

erly wired and in good electrical

condition. Always replace a damaged

extension cord or have it repaired by a

qualiﬁed person before using it.

• Protect your extension cords from sharp

objects, excessive heat and

damp or wet areas.

READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE.

Recommended Minimum Wire Gauge

for Extension Cords*

Extension Cord Length

* Based on limiting the line voltage drop to

ﬁve volts at 150% of the rated amperes.

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

25'

75'

100'

150'

50'

EXTENSION CORDS

WARNING

TOOL ASSEMBLY

To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making

adjustments. Use only speciﬁcally

recommended accessories. Others

may be hazardous.

Pipe Handle

The pipe handle may be used on either side

of the tool. Thread pipe handle into one of the

threaded holes in the motor housing.

Spade Handle (Fig. 2)

Installing Bits into Keyed Chucks (Fig.1)

1. Unplug tool.

2. Open the chuck jaws wide enough to

insert the bit. Be sure the bit shank and

chuck jaws are clean. Dirt particles may

prevent the bit from lining up properly.

3. Insert the bit into the chuck. Center the

bit in the chuck jaws and lift it about 1/16"

off of the bottom. Then, tighten the chuck

jaws by hand to align the bit.

4. Place the chuck key in each of the three

holes in the chuck, turning it clockwise.

Tighten securely.

5. To remove the bit, insert the chuck key

into one of the holes in the chuck and

turn it counterclockwise.

Bit Selection

• Use sharp bits. Sharp bits are less likely

to bind when drilling.

• Use the proper bit for the job. There are

many types of bits designed for speciﬁc

purposes. Check the information on the

bit's packaging for proper usage.

• Do not use bits larger than the rated

capacity of the drill. Gear damage or

motor overload may result.

The spade handle can be attached to the tool

in three positions (Fig. 2). Remove the hex

head screws which secure the handle. Re-

move the handle and move it to the desired

position. To mount the handle in position C,

it is necessary to reverse the mounting holes

by turning the handle around.

Fig. 2

Fig. 1

WARNING

To reduce the risk of injury, wear

safety goggles or glasses with side

shields. Unplug the tool before

changing accessories or making

adjustments.

OPERATION

WARNING

To reduce the risk of personal injury

when drilling, always hold tool by the

insulated gripping surfaces when

performing an operation where the

cutting tool may contact hidden wir-

ing or its own cord. Contact with a

"live" wire will make exposed metal

parts of the tool "live" and shock

the operator.

WARNING

When drilling with a single speed

drill or in HI with a two speed drill,

always hold the drill securely us-

ing the pipe handle, or brace the

drill against a solid ﬁxed object in

preparation for a sudden reaction.

When drilling in LO with a two speed

drill, always brace the drill against a

solid ﬁxed object in preparation for

a sudden reaction.

When drilling, never use your body

to brace drill.

Never put your hands (or other body

parts) between the part of the drill

being braced and the object it is be-

ing braced against. Hands (or other

body parts) that are in the path of the

reaction can be pinched, crushed

and broken.

Bracing for forward rotation

When drilling in forward, the bit will rotate in

a clockwise direction. If the bit binds in the

hole, the bit will come to a sudden stop and

drill will suddenly react in a counterclockwise

direction.

Figures 4 and 5 show examples of a Hole

Hawg

properly braced for forward rota-

tion.

A. Forward (clockwise) rotation

B. Reaction

C. Brace drill with pipe handle here

D. Brace drill with motor housing here

If the bit binds, the pipe handle or the motor

housing braced against the stud will hold the

drill in position.

Bit binding (Fig. 3)

If the bit binds, the drill will suddenly react

in the opposite direction of the rotation of

the bit. Figure 3 shows the path of reaction

(B) if the drill bit binds while being driven in

forward (A). The operator should reduce the

chances of a sudden reaction by following

the instructions listed below.

The operator should also prepare for a

sudden reaction by holding securely using

the pipe handle or bracing against a solid

ﬁxed object.

To reduce the chance of bit binding

• Use sharp bits. Sharp bits are less likely

to bind when drilling.

• Use the proper bit for the job. There are

many types of bits designed for speciﬁc

purposes.

• Use the proper speed for the size

bit. Larger bits should be run at the

lower speed. Driving larger bits at high

speeds will increase the chance of the

bit binding and increase the chance of

reaction.

• Avoid drilling warped, wet, knotty, and

or pitchy material if possible.

• Avoid drilling in material that you suspect

contains hidden nails or other things that

may cause the bit to bind.

The direction of reaction is always opposite

of the direction of bit rotation.

Reaction is even more likely to occur when

enlarging already existing holes and at the

point when the bit breaks through the other

side of the material.

Fig. 5

Fig. 4

Fig. 3

Bracing for reverse rotation

When drilling in reverse, the bit will rotate in

a counterclockwise direction. If the bit binds

in the hole, the bit will come to a sudden

stop and the drill will suddenly react in a

clockwise direction.

Figures 6 and 7 show examples of the

Hole Hawg

properly braced for reverse

rotation.

A. Reverse (counterclockwise) rotation

B. Reaction

C. Brace drill with pipe handle here

D. Brace drill with motor housing here

If the bit binds, the pipe handle or the motor

housing braced against the stud will hold the

drill in position.

Fig. 6

Fig. 7

Shifting Speeds (Fig. 8)

Cat. No. 1675-1 has

a gear shift lever on

the right side of the

gear case.

The h igh setting

(1200 RPM HI) is

the low torque setting

and is designed for

driving Selfeed bits

1-3/8" in diameter

and smaller.

The low setting (300

RPM LO) is the high

torque setting and is

designed for driving

Selfeed bits 1-1/2" in

diameter and larger.

Reversing (Fig. 9)

A reversing switch is located below the trig-

ger switch for removal of bits from holes.

Permit the motor to come to a complete stop

before reversing. Reversing the tool with the

gears in motion may cause severe damage.

When removing selfeed bits from partially

drilled holes, a ﬂick of the trigger switch

will free the threaded pilot screw. When the

threads are loose, lift the bit from the work-

piece with the motor stopped.

Fig. 9

Fig. 8

Chuck Removal

To remove the chuck from the drill:

1. Unplug tool.

2. Fully open the chuck jaws

3. Remove the left-handed thread screw

from inside the chuck by turning it clock-

wise.

4. Pull the chuck off of the spindle.

NOTE: If the chuck does not pull off of

the spindle easily, tap the side of the

chuck with a hammer to loosen it. If this

doesn't work, contact a MILWAUKEE

service center.

WARNING

To reduce the risk of injury, always

wear eye protection.

Drilling

Before drilling, clamp down the material

securely. A poorly secured piece of material

may result in personal injury or inaccurate

drilling. When drilling in light gauge metal or

wood, use a wooden block to back up the ma-

terial to prevent damage to the workpiece.

Mark the center of the hole to be drilled with

a center punch to give the bit a start and to

prevent it from "walking." Lubricate the drill

bit with cutting oil when drilling iron or steel.

Use a coolant when drilling nonferrous met-

als such as copper, brass or aluminum.

To start a selfeed bit, run the threaded feed

screw into the work by ﬂicking the trigger

switch, permitting the bit to coast until the

teeth contact the work surface. Align the bit

properly before proceeding. This will reduce

cocking and jamming when starting. To re-

duce jamming on breakthrough, decrease

the drilling pressure when the feed screw

point breaks through the workpiece. Proceed

with steady, even pressure.

Maintaining Tools

Keep your tool in good repair by adopting a

regular maintenance program. Before use,

examine the general condition of your tool.

Inspect guards, switches, tool cord set and

extension cord for damage. Check for loose

screws, misalignment, binding of moving

parts, improper mounting, broken parts and

any other condition that may affect its safe

operation. If abnormal noise or vibration oc-

curs, turn the tool off immediately and have

the problem corrected before further use.

Do not use a damaged tool. Tag damaged

tools “DO NOT USE” until repaired (see

“Repairs”).

Under normal conditions, relubrication is not

necessary until the motor brushes need to

be replaced. After six months to one year,

depending on use, return your tool to the

nearest MILWAUKEE service facility for the

following:

• Lubrication

• Brush inspection and replacement

• Mechanical inspection and cleaning

(gears, spindles, bearings, housing,

etc.)

• Electrical inspection (switch, cord,

armature, etc.)

• Testing to assure proper mechanical and

electrical operation

WARNING

To reduce the risk of injury, always un-

plug your tool before performing any

maintenance. Never disassemble the

tool or try to do any rewiring on the

tool's electrical system. Contact a

MILWAUKEE service facility for ALL

repairs.

WARNING

To reduce the risk of injury, electric

shock and damage to the tool, never

immerse your tool in liquid or allow a

liquid to ﬂow inside the tool.

MAINTENANCE

Cleaning

Clean dust and debris from vents. Keep

the tool handles clean, dry and free of oil

or grease. Use only mild soap and a damp

cloth to clean your tool since certain cleaning

agents and solvents are harmful to plastics

and other insulated parts. Some of these

include: gasoline, turpentine, lacquer thinner,

paint thinner, chlorinated cleaning solvents,

ammonia and household detergents con-

taining ammonia. Never use ﬂammable or

combustible solvents around tools.

Repairs

If your tool is damaged, return the entire tool

to the nearest service center.

ACCESSORIES

FIVE YEAR TOOL

LIMITED WARRANTY

WARNING

To reduce the risk of injury, always

unplug the tool before attaching or

removing accessories. Use only spe-

ciﬁcally recommended accessories.

Others may be hazardous.

For a complete listing of accessories refer to

your MILWAUKEE Electric Tool catalog or go

on-line to www.milwaukeetool.com. To obtain

a catalog, contact your local distributor or a

service center.

SÉCURITÉ DU LIEU

DE TRAVAIL

AVERTISSEMENT

LIRE SOIGNEUSEMENT TOUTES LES INSTRUCTIONS

Le non respect des instructions ci-après peut entraîner des chocs électriques, des

incendies et/ou des blessures graves. Le terme «outil électrique» ﬁgurant dans les

avertissements ci-dessous renvoie à l’outil électrique à alimentation par le réseau

(à cordon) ou par batterie (sans ﬁl).

CONSERVER CES INSTRUCTIONS

RÈGLES GÉNÉRALES DE SÉCURITÉ POUR LES OUTILS

ALIMENTÉS PAR BATTERIE

1. Maintenir la zone de travail propre et bien

éclairée. Les zones encombrées ou mal

éclairées sont favorables aux accidents.

2. Ne pas utiliser d’outil électrique dans

une atmosphère explosive, telle

qu’en en présence de liquides, de

gaz ou de poussières inﬂammables.

Les outils électriques génèrent des

étincelles qui peuvent enﬂammer les

poussières ou les fumées.

3. Tenir les enfants et les personnes

non autorisées à l’écart pendant le

fonctionnement d’un outil électrique.

Un manque d’attention de l’opérateur risque

de lui faire perdre le contrôle de l’outil.

4. La ﬁche de l’outil électrique doit cor-

respondre à la prise d’alimentation.

Ne jamais modifier la fiche d’une

manière quelconque. Ne pas utiliser

d’adaptateur avec les outils élec-

triques mis à la terre (à la masse).

Des ﬁches non modiﬁées et des prises

d’alimentation assorties réduisent le

risque de choc électrique.

Éviter tout contact corporel avec des

surfaces reliées à la masse ou à la

terre telles que tuyaux, radiateurs,

cuisinières et réfrigérateurs. Un risque

de choc électrique plus élevé existe si le

corps est relié à la masse ou à la terre.

Ne pas exposer les outils électriques

à la pluie ou à l’humidité. Le risque de

choc électrique augmente si de l’eau

s’inﬁltre dans un outil électrique.

9. Être sur ses gardes, être attentif et

faire preuve de bon sens en utilisant

un outil électrique. Ne pas utiliser

un outil électrique en cas de fatigue

ou sous l’influence de drogues,

d’alcool ou de médicaments. Un

instant d’inattention lors de l’utilisation

d’un outil électrique peut entraîner des

blessures graves.

10.

Utiliser un équipement de sécurité.

Toujours porter des lunettes de pro-

tection. Un équipement de sécurité

comprenant masque anti-poussière,

chaussures de sécurité anti-dérapantes,

casque ou dispositif de protection anti-

bruit peut, dans les circonstances appro-

priées, réduire le risque de blessure.

11.

Éviter tout démarrage accidentel de

l’outil. S’assurer que le commutateur

est en position OFF (Arrêt) avant de

brancher l’outil. Le port de l’outil avec

un doigt sur le commutateur ou son

branchement avec le commutateur en

position ON (Marche) sont favorables

aux accidents.

7. Prendre soin du cordon. Ne jamais

utiliser le cordon pour transporter,

tirer ou débrancher l’outil électrique.

Tenir le cordon à l’écart de la chaleur,

des huiles, des arêtes coupantes ou

des pièces en mouvement. Un cordon

endommagé ou emmêlé présente un

risque accru de choc électrique.

8. Se procurer un cordon d’alimentation

approprié en cas d’utilisation

d’un outil électrique à l’extérieur.

L’utilisation d’un cordon d’alimentation

pour usage extérieur réduit le risque de

choc électrique.

SÉCURITÉ INDIVIDUELLE

SÉCURITÉ ÉLECTRIQUE

Plastic Carrying Case

Cat. No. 48-55-0111

Type "E" Grease

Cat. No. 49-08-4122

Chuck Key Holder

Cat. No. 48-66-4040

Chuck Key

Cat. No. 48-66-3280

Every MILWAUKEE tool is tested before

leaving the factory and is warranted to be

free from defects in material and workman-

ship. MILWAUKEE will repair or replace (at

MILWAUKEE’s discretion), without charge,

any tool (including battery chargers) which

examination proves to be defective in ma-

terial or workmanship from ﬁve (5) years

after the date of purchase. Return the tool

and a copy of the purchase receipt or other

proof of purchase to a MILWAUKEE Factory

Service/Sales Support Branch location or

MILWAUKEE Authorized Service Station,

freight prepaid and insured. This warranty

does not cover damage from repairs made

or attempted by other than MILWAUKEE au-

thorized personnel, abuse, normal wear and

tear, lack of maintenance, or accidents.

The warranty period for V28 Battery Packs

is two (2) years from the date of purchase.

The warranty period for Ni-Cd battery Packs,

Flashlights, Radios are warranted for one (1)

year from the date of purchase.

THE REPAIR AND REPLACEMENT REM-

EDIES DESCRIBED HEREIN ARE EXCLU-

SIVE. IN NO EVENT SHALL MILWAUKEE

BE LIABLE FOR ANY INCIDENTAL, SPE-

CIAL, OR CONSEQUENTIAL DAMAGES,

INCLUDING LOSS OF PROFITS.

THIS WARRANTY IS EXCLUSIVE AND IN

LIEU OF ALL OTHER WARRANTIES, OR

CONDITIONS, WRITTEN OR ORAL, EX-

PRESSED OR IMPLIED FOR MERCHANT-

ABLILITY OR FITNESS FOR PARTICULAR

USE OR PURPOSE.

This warranty gives you speciﬁc legal rights.

You may also have other rights that vary from

state to state and province to province. In

those states that do not allow the exclusion of

implied warranties or limitation of incidental

or consequential damages, the above limi-

tations or exclusions may not apply to you.

This warranty applies to the United States,

Canada, and Mexico only.

Milwaukee 1676-6 Manuel utilisateur

Marque: Milwaukee

Modèle: 1676-6

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Milwaukee 1676-6 User manual

Documents connexes

Autres documents

Genesis GSHD1290 Manuel utilisateur