Superior Fireplaces DRL6000 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRL6000

Catégorie: Poêles

Taper: Mode d'emploi

Installation and Operation Instructions

Direct-Vent Linear Gas Fireplace

P/N 901077-00 REV. D 01/2021

Report No. F18-195

CUS

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:

RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité

pourrait d’entraîner des blessures graves, la mort

ou des dommages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inﬂammables dans le voisinage

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où

vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualiﬁé

ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future

reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour

consultation ultérieure.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or

mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated

on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements

locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque

signalétique. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

Ce manuel est disponible en francais, simple-

ment en faire la demande. Numéro de la pièce

901077-01.

DRL6072TEN

DRL6084TEN

DRL6060TEN-B

Models

P901077-00

SuperiorFireplaces.us.com 901077-00D2

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is pro-

vided with this appliance and must be installed for the protection of children and

other at-risk individuals.

DANGER

PELIGRO

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED NUNCA DEBE

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS NUNCA DEBE

TOCAR EL VIDRIO.

L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de

contact accidentel avec la vitre chaude et doit être installé pour la protection Des

enfants et Des personnes à risques.

Se provee con este aparato una barrera de proteccion (malla), diseñada para reducir

el riesgo de quemaduras por contacto accidental con el vidrio caliente que debe

estar instalada para proteccion de infantes y otros individuos en riesgo.

Vea el volante adjunto para la representación de color adecuado

See attached color ﬂyer for proper color representation

Voir ci-joint tract pour une bonne représentation de la couleur

SAFETY AND YOUR FIREPLACE

SuperiorFireplaces.us.com901077-00D 3

 Aﬁn d’éviter les brûlures

graves ou les blessures,

ne pas retirer l’écran de

protection de la foyer qui

empêche tout contact

direct avec la vitre.

 Suivez les instructions de sécurité

ci-dessous et veillez à ce que tous

les membres de votre famille soient

conscients du danger de brûlure

encouru :

• Les surfaces de votre foyer deviennent

EXTRÊMEMENT CHAUDES !

• La vitre située à l'avant du foyer atteint

des températures EXTRÊMEMENT

ÉLEVÉES et peut causer de graves

blessures en cas de contact.

• Tenez les enfants à l'écart du foyer

lorsqu'il fonctionne. Surveillez

attentivement les enfants dans les

pièces où un foyer est utilisé aﬁn

d'éviter qu'ils ne soient en contact avec

la vitre.

• Tenez tous les vêtements, les meubles,

l'essence et tout autre liquide

inﬂammable à l'écart du foyer.

• Même après fermeture du gaz, les

surfaces du foyer restent extrêmement

chaudes.

 Veillez à coller les Étiquettes de mise

en garde relatives à la sécurité

d'utilisation à l'endroit où vous

utilisez le foyer, pour rappeler à tous

les utilisateurs les dangers liés aux

températures élevées

(Page 37)



Lisez L’information de sûreté

importante (Page 4)

Para evitar quemaduras y lesiones

graves, no quite el protector de malla

o guardia de seguridad que evita el

contacto directo con el vidrio.

 Siga las instrucciones de seguridad

a continuación y asegúrese de que

todos en su hogar sepan acerca de este

peligro de quemadura:

• ¡Las superﬁcies de la chimenea

estarán EXTREMADAMANTE

CALIENTES!!

• El vidrio delante de la

chimenea alcanza temperaturas

EXTREMADAMENTE ALTAS y puede

causar quemaduras graves si se toca.

• Mantenga a los niños alejados de

la chimenea en funcionamiento.

Supervise en forma cercana a los niños

en cualquier cuarto donde haya una

chimenea funcionando para impedir el

contacto con el vidrio.

• Mantenga la ropa, mobiliario, gasolina

y otros líquidos inﬂamables alejados

de la chimenea.

• Aún después de haber apagado el

gas, las superﬁcies de la chimenea

permanecen extremadamente

calientes.

 Asegúrese de colocar las Etiquetas de

advertencia de seguridad de operación

en el lugar donde enciende la chimenea,

para que todos recuerden los peligros

asociados con las altas temperaturas

(Página 37)



Lea Información importante de

seguridad (Página 4).

Seguridad y su

chimenea

La sécurité et

votre foyer

[FRENCH][ENGLISH]

[SPANISH]

Safety and Your

Fireplace

 To prevent severe burns

and injuries, do Not

remove the barrier on the

appliance which prevents

direct contact with the

glass.

 Follow the safety instructions below

and be sure everyone in your household

understands this burn hazard:

• The surfaces on your ﬁreplace get

EXTREMELY HOT!

• The glass on the front of the

ﬁreplace reaches EXTREMELY HIGH

temperatures and can cause severe

burns if touched.

• Keep children away from an operating

ﬁreplace. Closely supervise children

in any room where a ﬁreplace is

operating to prevent contact with glass.

• Keep clothing, furniture, gasoline, and

other ﬂammable liquids away from the

ﬁreplace.

• Even after the gas is turned off,

ﬁreplace surfaces remain extremely

hot.

 Be sure to attach the enclosed Safety-

in-Operation Warnings where you

turn on your ﬁreplace, to help remind

everyone of the dangers associated with

high temperatures

(Page 37)

 Read Important Safety Information

(Page 4)

All parts of your

IHP ﬁreplace get

EXTREMELY HOT!

Toutes les parties de votre

foyer IHP deviennent

EXTRÊMEMENT CHAUDES !

¡Todas las partes de la

chimenea IHP se ponen

MUY CALIENTES!

SuperiorFireplaces.us.com 901077-00D4

Important Safety Information

1. WARNING: Do not operate appliance

with the glass front removed, cracked,

or broken.

2. Do not use this appliance if any part

has been under water. Immediately

call a qualiﬁed service technician to in-

spect the appliance and to replace any

part of the control system and any gas

control which has been under water.

3. Due to high temperatures, the appli-

ance should be located out of trafﬁc

and away from furniture and draperies.

4. Children and adults should be alerted

to the hazards of high surface tem-

perature and should stay away to avoid

burns or clothing ignition.

5. Clothing or other ﬂammable material

should not be placed on or near the

appliance.

6. Young children should be carefully

supervised when they are in the same

room as the appliance. Toddlers,

young children, and others may be sus-

ceptible to accidental contact burns.

A physical barrier is recommended

if there are at-risk individuals in the

house. To restrict access to a ﬁreplace

or stove, install an adjustable safety

gate to keep toddlers, young children,

and other at-risk individuals out of the

room and away from hot surfaces.

7. Any safety screen, guard or barrier

removed for servicing an appliance

must be replaced prior to operating

the appliance.

8. Installation and repair should be done

by a qualiﬁed service person. The ap-

pliance should be inspected before use

and at least annually by a professional

service person. More frequent clean-

ing may be required due to excessive

lint from carpeting, bedding material,

et cetera. It is imperative that control

compartments, burners, and circulat-

ing air passageways of the appliance

be kept clean. See maintenance in-

structions on Page 48.

L’information de sûreté

importante

1. AVERTISSEMENT. Ne pas utiliser l’appareil

si le panneau frontal en verre n’est pas en

place, est craqué ou brisé.

2. Ne pas se servir de cet appareil s’il a été

plongé dans l’eau, même partiellement.

Faire inspecter l'appareil par un technicien

qualiﬁé et remplacer toute partie du systéme

de contrôle et toute commande qui ont été

plongées dans l'eau.

3. En raison des températures élevées,

l’appareil devrait être installé dans un en

droit où il y a peu de circulation et loin du

mobilier et des tentures.

4. Les enfants et les adultes devraient être

informés des dangers que posent les tem-

pératures de surface élevées et se tenir à

distance aﬁn d’éviter des brûlures ou que

leurs vêtements ne s’enﬂamment.

5. On ne devrait pas placer de vêtements

ni d’autres matières inflammables sur

l’appareil ni à proximité.

6. Les jeunes enfants devraient être surveillés

étroitement lorsqu’ils se trouvent dans la

même pièce que l’appareil. Les tout petits,

les jeunes enfants ou les adultes peuvent

subir des brûlures s’ils viennent en contact

avec la surface chaude. Il est recommandé

d’installer une barrière physique si des

personnes à risques habitent la maison.

Pour empêcher l’accès à un foyer ou à un

poêle, installez une barrière de sécurité

; cette mesure empêchera les tout petits,

les jeunes enfants et toute autre personne

à risque d’avoir accès à la pièce et aux

surfaces chaudes.

7. Tout écran ou protecteur retiré pour per

mettre l’entretien de l’appareil doit être

remis en place avant de mettre l’appareil

en marche.

8. L’installation et la réparation devrait être

conﬁées à un technicien qualiﬁé. L’appareil

devrait faire l’objet d’une inspection par un

technicien professionnel avant d’être utilisé

et au moins une fois l’an par la suite. Des

nettoyages plus fréquents peuvent être

nécessaires si les tapis, la literie, et cetera

produisent une quantité importante de pous-

sière. Il est essentiel que les compartiments

abritant les commandes, les brûleurs et les

conduits de circulation d’air de l’appareil

soient tenus propres. Voyez les instructions

d’entretien à la Page 48.

Información importante de

seguridad

1. ADVERTENCIA: No opere el artefacto con el

frente de vidrio quitado, agrietado o roto.

2. No use este artefacto si alguna de sus partes

ha estado bajo agua. Llame de inmediato

a un técnico de servicio caliﬁcado para

que inspeccione el artefacto y reemplace

cualquier parte del sistema de control y

cualquier control de gas que haya estado

bajo agua.

3. Debido a las altas temperaturas, el artefacto

debe situarse fuera de las áreas de tráﬁco y

lejos del mobiliario y cortinas.

4. Se debe alertar a los niños y adultos sobre

los peligros de las altas temperaturas en la

superﬁcie y que se mantengan alejados para

evitar quemaduras o ignición de la ropa.

5. No debe colocarse ropa u otros materiales

inﬂamables sobre y cerca del artefacto.

6. Se debe supervisar de cerca a los niños

cuando estén en el mismo cuarto que el

artefacto. Los niños pequeños, los jóvenes

y otras personas pueden ser susceptibles

a quemaduras por contacto accidental. Se

recomienda instalar una barrera física si hay

personas en riesgo en la casa. Para restringir

el acceso a una chimenea o estufa, instale

una puerta de seguridad ajustable para

mantener a los niños pequeños, jóvenes y

otras personas en riesgo fuera del cuarto y

lejos de las superﬁcies calientes.

7. Cualquier malla o resguardo de seguridad

quitado para dar servicio a un artefacto, debe

reinstalarse antes de operar el artefacto.

8. Una persona de servicio competente debe

realizar la instalación y reparación. Una

persona de servicio profesional debe

inspeccionar el artefacto antes de usar al

menos una vez por año. Se puede requerir

limpieza más frecuente debido a la pelusa

excesiva del alfombrado, del material de

cobijas, etc. Es imprescindible mantener

limpios los compartimientos de control, los

quemadores y los pasajes de circulación del

aire del artefacto. Ver las instrucciones de

mantenimiento en la página 48.

IMPORTANT SAFETY INFORMATION

SuperiorFireplaces.us.com901077-00D 5

Thank you for your purchase. We appreciate your business!

Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety information.

Following these safety, care, and operation instructions will help ensure many years of dependable and enjoyable service from your ﬁreplace.

Please read and understand these instructions before installing or operating.

TABLE OF CONTENTS

Safety and Your Fireplace .............................................................. 2

Important Safety Information ........................................................ 4

Safety ............................................................................................ 6

Local Codes .................................................................................. 8

Product Features ........................................................................... 8

Packaging ..................................................................................... 8

Product Identiﬁcation .................................................................... 9

Requirements for the Commonwealth of Massachusetts ............. 9

Cold Climate Insulation ................................................................. 9

High Altitude Requirements ........................................................ 10

Manufactured Home Requirements ............................................ 10

Typical Locations ........................................................................ 10

Pre-installation ............................................................................ 11

Framing and Finishing ................................................................. 12

Installing TV above Fireplace ....................................................... 14

Termination Location and Clearances.......................................... 17

Venting Installation ..................................................................... 18

Fireplace Installation ....................................................................27

Finishing Fireplace .......................................................................34

Attaching Safety Operation Warnings ..........................................37

Operation .....................................................................................38

Cleaning and Maintenance ...........................................................48

Maintenance Schedule .................................................................50

Wiring Diagram ............................................................................51

Gas Conversion Kits .....................................................................52

Speciﬁcations ...............................................................................53

Technical Service .........................................................................53

Replacement Parts .......................................................................53

Service Hints ................................................................................ 53

Troubleshooting ...........................................................................54

Parts ............................................................................................55

Optional Accessories ....................................................................58

Warranty ......................................................................................61

SuperiorFireplaces.us.com 901077-00D6

WARNING

Do not slam or strike glass doors. Damage can

result in a hazardous condition.

CAUTION

Hot while in operation. Do not touch. Severe Burns may

result. Keep children, clothing furniture, gasoline and

other liquids having ﬂammable vapors away.

Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children and others may be

susceptible to accidental burns. A physical barrier

is recommended if there are at-risk individuals in

the house. To restrict access to a ﬁreplace or stove,

install an adjustable safety gate to keep toddlers,

young children and other at-risk individuals out of

the room and away from hot surfaces.

ATTENTION

L’appareil est chaud lorsqu’il fonctionne. Ne pas

toucher l’appareil. Risque de brûlures graves.

Surveiller les enfants. Garder les vêtements, les

meubles, l’essence ou autres liquides produisant

des vapeur inﬂammables loin de l’appareil.

SAFETY

WARNING

Improper installation, adjustment, alteration,

service or maintenance can cause injury or property

damage. Refer to this manual. For assistance or

additional information consult a qualiﬁed installer,

service agency or the gas supplier.

AVERTISSEMENT

Une installation, un réglage,une modiﬁcation,

une réparation ou un entretien mal effectué peut

causer des dommages matériels ou des blessures.

Voir la notice de l’utilisateur qui accompagne

l’appareil. Pour de l’aide ou des renseignements

supplémentaires, consultez un installateur, un

technicien agréé ou le fournisseur de gaz.

IMPORTANT

Read this owner’s manual carefully and completely

before trying to assemble, operate or service this

ﬁreplace. Improper use of this ﬁreplace can cause

serious injury or death from burns, ﬁre, explosion,

electrical shock and carbon monoxide poisoning.

WARNING

This product can expose you to chemicals including

Carbon Black, which is known to the State of Califor-

nia to cause cancer, and Carbon Monoxide, which is

known to the State of California to cause birth defects

or other reproductive harm. For more information go

to www.P65Warnings.ca.gov

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

State of Massachusetts: The installation must be

made by a licensed plumber or gas ﬁtter in the

Commonwealth of Massachusetts.

AVERTISSEMENT

Ce produit peut vous exposer à des produits chimiques,

y compris du carbone noir qui est reconnu par l'État

de Californie comme un produit cancérigène, et du

monoxyde de carbone, qui est reconnu par l'État de

Californie comme pouvant causer des déformations

fœtales ou perturber la fonction reproductive. Pour plus

d’information, aller sur www.P65Warnings.ca.gov

These vented gas ﬁreplace heaters are sealed combustion, air-

circulating gas ﬁreplaces designed for residential, manufactured

home, and commercial applications. Direct-vent appliances

operate with the combustion chamber isolated from the indoor

environment. All air for combustion is brought in from the outside,

and exhaust gases are vented through the same direct-vent, coaxial

(intake/exhaust) vent system. These ﬁreplaces must be installed

with IHP 6DVL Direct Vent Pipe components and terminations.

This ﬁreplace must be installed by a qualiﬁed (certiﬁed or licensed)

service person. If the glass door assembly and venting pipe are not

properly seated, connected and sealed, carbon monoxide leakage

(spillage) can occur.

SuperiorFireplaces.us.com901077-00D 7

SAFETY Continued

WARNING

Any change to this ﬁreplace or its controls can be

dangerous. Do not modify this ﬁreplace under any

circumstances. Any parts removed for servicing

must be replaced prior to operating ﬁreplace.

WARNING

Do not use a blower insert, heat exchanger insert

or other accessory not approved for use with this

ﬁreplace.

WARNING

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases unless a

certiﬁed kit is used.

WARNING

Do not allow fans to blow directly into the ﬁreplace.

Avoid any drafts that alter burner ﬂame patterns.

Due to high temperatures, the appliance should be

located out of trafﬁc and away from furniture and

draperies.

Do not place clothing or other ﬂammable material

on or near the appliance. Never place any objects

on the appliance.

Do not use this ﬁreplace to cook food or burn paper

or other ﬂammable material.

DANGER

Carbon monoxide poisoning may lead to death!.

Carbon Monoxide Poisoning: Early signs of carbon monoxide poison-

ing resemble the ﬂu, with headaches, dizziness or nausea. If you have

these signs, the ﬁreplace may not be working properly. Get fresh air

at once! Have ﬁreplace serviced. Some people are more affected by

carbon monoxide than others. These include pregnant women, people

with heart or lung disease or anemia, those under the inﬂuence of

alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural gas is odorless, although it has

an odor-making agent added to the gas. Propane/LP gas has a natural

odor. The odor helps you detect a gas leak. However, the odor added

to the gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this

manual for reference. It is your guide to safe and proper operation

of this ﬁreplace.

Carefully supervise young children when they are

in the room with ﬁreplace.

Keep the area around your ﬁreplace clear of com-

bustible materials, gasoline and other ﬂammable

vapor or liquids. Do not run ﬁreplace where these

are used or stored.

This ﬁreplace reaches high temperatures. Keep chil-

dren and adults away from hot surface to avoid burns

or clothing ignition. Fireplace will remain hot for a time

after shutdown. Allow surface to cool before touching.

1. For propane/LP ﬁreplace, do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP supply tank(s) outdoors.

To prevent performance problems, do not use propane/LP fuel

tank of less than 100 lb. capacity.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in your

building

• leave the building immediately

• immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier's instructions

• if you cannot reach your gas supplier, call the ﬁre department.

3. Never install the ﬁreplace

• in a recreational vehicle

• in windy or drafty areas where curtains or other combustible

(ﬂammable) objects can make contact with the ﬁreplace front

• in high trafﬁc areas

4. Turn ﬁreplace off and let cool before servicing, installing or

repairing. Only a qualiﬁed service person should install, service

or repair this ﬁreplace. Have ﬁreplace inspected annually by a

qualiﬁed service person.

5. You must keep control compartments, burners and circulating

air passages clean. More frequent cleaning may be needed due

to excessive lint and dust from carpeting, bedding material, etc.

Turn off the gas valve and pilot light before cleaning ﬁreplace.

6. Have ﬁreplace and venting system inspected annually by a quali-

ﬁed service person. If needed, have venting system cleaned or

repaired. See Cleaning and Maintenance, Page 48.

7. Do not use any solid fuels (wood, coal, paper, cardboard, etc.)

in this ﬁreplace. Use only the gas type indicated on ﬁreplace

nameplate.

8. This appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes,

with the National Electrical Code, ANSI/NFPA 70 or Canadian

Electrical Code, CSA C22.1.

9. Do not use ﬁreplace if any part has been exposed to or under

water. Immediately call a qualiﬁed service person to arrange for

replacement of the unit.

10. Do not operate ﬁreplace with glass door removed, cracked or

broken.

11. Provide adequate clearances around air openings.

SuperiorFireplaces.us.com 901077-00D8

LOCAL CODES

Install and use ﬁreplace with care. Follow all local codes. In the ab-

sence to local codes, use the current National Fuel Gas Code ANSI

Z223.1/NFPA 54* (USA) or the current CAN/CGA B149.1 Installation

Code (Canada).

*Available from:

American National Standards Institute, Inc.

25 West 43rd Street, 4th ﬂoor

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02169-7471

Codes and Standards

Listing: These ﬁreplaces comply with National Safety Standards and

are tested and listed by PFS TECO (Report No. F18-195) to ANSI

Z21.88 (in Canada, CSA-2.33), and CSA 2.17-2017/CGA 2.17 -M91

(R2014) in both USA and Canada, as vented gas ﬁreplace heaters.

These appliances comply with CSA P.4.1-2015 “Testing Method

for Measuring Annual Fireplace Efﬁciency. P4 (EnerGuide) is a

measurement of the Canadian Ofﬁce of Energy Efﬁciency.

These ﬁreplaces are listed for installation in bedrooms, aftermarket

mobile homes, and manufactured homes.

The installation must conform to local codes or, in the absence of

local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA

54—latest edition, or the Natural Gas and Propane Installation

Code, CSA B149.1.

The ﬁreplace, when installed, must be electrically grounded and

wired in accordance with local codes or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA 70—latest

edition, or the Canadian Electrical Code, CSA C22.1—latest edition.

PRODUCT FEATURES

These are a few facts that can help you understand and enjoy your

direct vent ﬁreplace:

• The venting system may be routed to the outside of your home in

several ways. It may vent through the roof (vertical) or it may vent

to an outside/exterior wall (horizontal). The vent pipe installation is

very important to allow for proper operation. You must follow the

venting instructions very carefully for either vertical or horizontal

applications.

• This ﬁreplace may be installed in any room of your house provided

all local codes and these installation instructions are followed.

• Each time you turn on your ﬁreplace, you may notice some amount

of condensation on the inside of the ﬁreplace glass. This is normal

and will disappear after 10-20 minutes of operation.

• Your direct vent ﬁreplace system (ﬁreplace and venting) is a bal-

anced and sealed combustion system. It requires approximately

10-20 minutes of operating time before the ﬂame pattern stabilizes.

PACKAGING

The assembled Direct Vent Gas Fireplace is packaged with:

• Literature Kit (Installation and Operation Instructions (this

manual)), Hot Glass Safety Flyer, and Safety-In-Operation Warn-

ing Labels.

• Platinum Glass Media -

60" Models - Three (3), 5 lb. bags

72" Models - Four (4), 5 lb. bags

84" Models - Five (5), 5 lb. bags

• One (1), Hand Held Remote Control

• Four (4), AA Batteries

• Three (3), AAA Batteries

• One (1), Fireboard Top

• One (1), Fireboard Bottom

• Two (2), Fireboard Sides

• Self Drill Bugle Drywall Screws

(to attach Fireboard)

• One (1) Standoff Assembly (see Figure 1)

• One (1) Heat Shield (see Figure 1)

• Twelve (12) #10 Hex Head Screws

SuperiorFireplaces.us.com901077-00D 9

PRODUCT IDENTIFICATION

REQUIREMENTS FOR THE COMMONWEALTH OF

MASSACHUSETTS

These appliances are approved for installation in the U.S. state of

Massachusetts if the following additional requirements are met:

• Install this ﬁreplace in accordance with Massachusetts Rules

and Regulations 248 C.M.R. 4.00 through 8.00.

• Installation and repair must be done by a plumber or gas ﬁtter

licensed in the Commonwealth of Massachusetts.

• The ﬂexible gas line connector used shall not exceed 36” (914

mm) in length.

• The individual manual shutoff must be a T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, horizontal terminations

installed less than seven (7) ft above the ﬁnished grade must

comply with the following additional requirements:

• A hard wired carbon monoxide detector with an alarm and

battery back-up must be installed on the ﬂoor level where the

gas ﬁreplace is installed. The carbon monoxide detector must

comply with NFPA 720, be ANSI/UL 2034 listed and be CSA

certiﬁed.

• A metal or plastic identiﬁcation plate must be permanently

mounted to the exterior of the building at a minimum height

of eight (8) ft above grade and be directly in line with the

horizontal termination. The sign must read, in print size no

less than one-half (1/2) inch in size, GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks around your ﬁreplace

with noncombustible material and wherever cold air could enter

the room. It is especially important to insulate outside chase cavity

between studs and under ﬂoor on which ﬁreplace rests, if ﬂoor

is above ground level. Gas line holes and other openings should

be caulked or stuffed with unfaced ﬁberglass insulation. Caulk the

ﬁrestop only where the pipe penetrates an outside wall, attic, or

other unconditioned space.

NOTE: Caulking used must have a minimum of 300°F continuous

exposure rating.

NOTE: Do not use loose, or blown-in insulation in the cavity

surrounding the ﬁreplace.

If the ﬁreplace is being installed on a cement slab in cold climates, a

sheet of plywood or other raised platform can be placed underneath

to prevent conduction of cold transferring to the ﬁreplace and into

the room. It also helps to sheetrock inside surfaces and tape for

maximum air tightness and caulk ﬁrestops.

Glass Door

Gas Connection

Access Door

Cover

Barrier

Fireboard Nailing Flange

(Standoff Assembly)

Nailing Flange

Fireplace Top

Spacers

Heatshield

Figure 1 - Component Overview

SuperiorFireplaces.us.com 901077-00D10

MANUFACTURED HOME REQUIREMENTS

This appliance may be installed in an aftermarket, permanently

located, manufactured home (USA only) or mobile home, where

not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the

rating plate. This appliance is not convertible for use with other

gases, unless a certiﬁed kit is used.

CAUTION

Ensure that the cross members are not cut or

weakened during installation. The structural

integrity of the manufactured home ﬂoor, wall, and

ceiling / roof must be maintained.

CAUTION

This appliance must be grounded to the chassis of

the manufactured home in accordance with local

codes or in the absence of local codes, with the

National Electrical Code ANSI / NFPA 70—latest

edition or the Canadian Electrical Code CSA C22.1—

latest edition.

TYPICAL LOCATIONS

In selecting the location, the aesthetic and functional use of the

ﬁreplace are primary concerns. However, vent system routing to

the exterior and access to the fuel supply are also important. The

ﬁreplace may be located on or near conventional construction

materials. See Location and Space requirements Page 11 for

more information.

Due to high temperatures, the appliance should be located out of

trafﬁc and away from furniture and draperies.

The location should also be free of electrical, plumbing or other

heating/air conditioning ducting.

Be aware that this is a heat producing ﬁreplace. Objects placed

above the unit are exposed to elevated temperatures. Do not

insulate the space between the ﬁreplace and the area above it.

Figure 2 - Typical Locations and Venting

HIGH ALTITUDE REQUIREMENTS

Oriﬁce Sizes—Sea Level to High Altitude

These ﬁreplaces are tested and approved for installation at

elevations of 0–4500 ft (0–1372 m) above sea level using the

standard burner oriﬁce sizes (see speciﬁcations table, Page 53).

For elevations above 4500 ft, contact your gas supplier or qualiﬁed

service technician.

Deration

At elevations above 4500 ft, the amount of BTU fuel value delivered

must be reduced by either:

• Using gas that has been derated by the gas company.

• Changing the burner oriﬁce to a smaller size as regulated

by the local authorities having jurisdiction and by the (USA)

National Fuel Gas Code NFPA 54/ANSI Z223.1—latest edition

or, in Canada, the CAN/CGA-B149.1 codes—latest edition.

IN CANADA - CSA 2.17-2017/CGA 2.17 -M91 (R2014) (HIGH

ALTITUDE):

The conversion shall be carried out by a manufacturer’s authorized

representative, in accordance with the requirements of the

manufacturer, provincial or territorial authorities having jurisdiction

and in accordance with the requirements of the CAN/CGA-B149.1

or CAN/CGA-B149.2 Installation codes.

NOTE: Framing details not shown. This illustrates typical locations only.

Top Vent

Top Vent Top Vent

Top Vent - See-Thru

Recessed

Installation

Fireplace

Fireplace Collar

Vertical

Termination

Horizontal

Termination

SuperiorFireplaces.us.com901077-00D 11

PRE-INSTALLATION

LOCATION AND SPACE REQUIREMENTS

Determine the safest and most efﬁcient location for your direct vent ﬁreplace.

Make sure that rafters and wall studs are not in the way of the venting system.

Choose a location where the heat output is not affected by drafts, air condi-

tioning ducts, windows or doors. Be aware of all restrictions and precautions

before deciding the exact location for your ﬁreplace and termination cap.

When deciding the location of your ﬁreplace, follow these rules:

• Do not connect this ﬁreplace venting to a chimney ﬂue serving a separate

solid-fuel burning ﬁreplace or appliance.

• Due to high temperatures, do not locate this ﬁreplace in high trafﬁc areas,

windy or drafty areas or near furniture or draperies.

• Proper clearances must be maintained.

• If your ﬁreplace is to be installed directly on carpeting, vinyl tile or any

combustible material other than wood, it must be installed on a metal or

wood panel extending the full width and depth of the ﬁreplace (see Figure

11, Page 16).

• Standoff spacers attached to your ﬁreplace can be placed directly against

the wall or framing material. See framing details, Pages 12-15.

• When locating the termination cap, it is important to observe the minimum

clearances shown in Table 2, Page 17.

• Do not recess the termination cap into a wall or siding.

• You may paint the termination cap with high temperature heat-resistant

paint to coordinate with the exterior ﬁnish.

• There must not be any obstruction such as bushes, garden sheds, fences,

decks or utility buildings within 24" from the front of the termination cap

and the front of outside air vent.

• Do not locate the termination cap and outside air vent where excessive

snow or ice build up may occur. Be sure to clear vent termination area

after snow falls to prevent accidental blockage of venting system. When

using snow blowers, do not direct snow towards vent termination area.

NOTICE

This ﬁreplace is intended for use as supplemental heat.

Use this ﬁreplace along with your primary heating sys-

tem. Do not install this ﬁreplace as your primary heat

source. If you have a central heating system, you may

run system’s circulating blower while using ﬁreplace.

This will help circulate the heat throughout the house

CLEARANCES

Minimum clearances to combustibles for the ﬁreplace are as follows:

Table 1 - Minimum Clearances

Back 1” (26 mm) to wrapper

Sides

1” (26 mm) to wrapper

0” (0 mm) to Spacers

Top of Fireboard Nailing Flange 0” (0 mm)

Floor 0” (0 mm)

From Bottom of Unit to Ceiling 84” (2134 mm)

Enclosure Height 84" (2134 mm)

Horizontal Vent

3” (77 mm) - Top,

1" (26 mm) - Sides and Bottom

Vertical Vent 1” (26 mm)

Front Clearance — clearance immedi-

ately in front of viewing area(s)

36” (914 mm)

Do not pack with insulation or other materials around the ﬁreplace.

Figure 3 - Standoff Installation and Clearance to Combustibles

IMPORTANT! TOP STANDOFF AND HEATSHIELD SUB-ASSEMBLY MUST BE INSTALLED PRIOR TO APPLIANCE INSTALLATION!

Identify top standoff sub-assembly and heat shield packaged on top of appliance during shipping.

2. Using screws provided, attach assembly to forward portion of appliance top as shown in Figure 3.

NOTE: If appliance is being upgraded to a See-Thru application, install second top standoff sub-assembly and heat shield to the rear portion of ap-

pliance top as supplied with and shown in the See-Thru kit instructions.

Fireboard

Nailing Flange

Venting

Heatshield

Wrapper

Back

Wrapper

Side

Nailing

Flange

Floor

Fireplace

Top

Spacer

Flue

Connector

Gas

Connection

Glass Door

SuperiorFireplaces.us.com 901077-00D12

ONE SIDED / SEE-THRU INSTALLATION

Fireplace Framing

1. Frame the ﬁreplace as illustrated in Figures 4-9, Pages 12-15.

All framing details must allow for a minimum clearances to

combustible framing members as shown in Table 1, Page 11.

2. Mount the ﬁreplace on the ﬂoor or on a fully supported base

extending the full width and depth of the unit. If installed

over combustible materials, such as carpeting, vinyl tile, or

combustible material other than wood ﬂooring, the appliance

must be installed on a metal or wood panel extending the full

width and depth of the ﬁreplace.

3. Headers may be in direct contact with the top of the nailing

ﬂange, maintaining the 11” clearance to the ﬁreplace top, but

must not be supported by them or notched to ﬁt around them

after self supporting (see Figure 4). All construction above the

ﬁreplace must be self-supporting. DO NOT use the ﬁreplace for

structural support.

4. All minimum clearances must be met. Vent pipe needs to

maintain 1" clearance. Wood studs may be notched. Fireboard

is provided for facing around the ﬁreplace.

5. If you are using a separate combustible mantel piece, refer to

Figure 40, Page 34 for proper installation height.

NOTE: Fireplace is designed for 1/2” thickness of non-combustible

ﬁreboard on the face of the unit (Included with one sided application).

If installing a two sided application, the non-combustible ﬁreboard

will be included with the See-Thru kit, see accessories Page 58).

IMPORTANT! Before you begin framing, determine whether

you will be installing the ﬁreplace as a one sided application

or See-Thru application. If installing a TV above the

ﬁreplace, a HeatFlo Kit is required (see Accessories, Page

58). Follow instructions included with the Kit and framing

details in this manual.

The ﬁreplace will come factory installed as a one sided appliance.

If you will be using the ﬁreplace for a one sided regular application,

you can install it as is. If you will be upgrading the ﬁreplace to a

See-Thru application a conversion kit is required (see Accessories,

Page 58). Follow instructions included with the Kit.

NOTE: The optional Blower Kit is not compatible with the See-Thru Kit.

If the Blower Kit is installed, it must be removed or disabled when a

See-Thru Kit is installed.

FRAMING AND FINISHING

Figure 4 - Framing Flush Wall (Standard Installation)

Framing Dimensions Standard Installation - Inches (millimeters)

A B

60” Models

One Sided

Framing

74-1/4

(1886)

19-1/2

(496)

48-1/2

(1232)

(2134)

See-Thru

Framing

74-1/4

(1886)

18-1/2

(469)

48-1/2

(1232)

(2134)

72” Models

One Sided

Framing

86-1/4

(2191)

19-1/2

(496)

48-1/2

(1232)

(2134)

See-Thru

Framing

86-1/4

(2191)

18-1/2

(469)

48-1/2

(1232)

(2134)

84” Models

One Sided

Framing

98-1/4

(2496)

19-1/2

(496)

48-1/2

(1232)

(2134)

See-Thru

Framing

98-1/4

(2496)

18-1/2

(469)

48-1/2

(1232)

(2134)

• Optional See-Thru Kit required for See-Thru installation

* Minimum height from appliance base to ceiling

Fireplace Framing Standard Installation (Flush Wall)

Secure Nailing

Flanges to

Framing

Secure Fireboard

Nailing Flange(Front

and Inside of

Framing)

SuperiorFireplaces.us.com901077-00D 13

FRAMING AND FINISHING Continued

IMPORTANT NOTICE

A HEATFLO KIT IS REQUIRED IF INSTALLING A TV ABOVE THE FIREPLACE.

WARNING

Ensure clearances to combustibles are maintained when building a mantel or shelves above the fireplace.

Elevated temperatures on the wall or in the air above the fireplace can cause melting, discoloration or damage

to decorations, a television (TV) or other electronic components.

IMPORTANT NOTICE

Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing

so may negatively affect the longevity of the television and may negate the warranty. If you do place a

television above the ﬁreplace, please be aware of the large amount of heat generated by the ﬁreplace and

consider placing the television above the ﬁreplace at 12” minimum on a ﬂush wall and at 18" for a recessed

installation, to reduce the amount of heat that reaches the television. The homeowner must understand that

IHP does not take responsibility for any negative impact to televisions placed near this ﬁreplace.

TVs should not be used in situations where the actual TV temperature exceeds the manufacturer’s technical

specification. Contact the TV manufacturer directly if you cannot locate this information or have questions

regarding this information.

NOTE: Clearances to TV are provided only for guidance, please follow TV manufacturer's recommendation for

installation.

INSTALLING TELEVISION (TV) ABOVE FIREPLACE

The following section details two options for installing a television (TV) above Fireplace

See Figures 6-9 for TVs Installed above the ﬁreplace:

WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to protect from

contact with hot surfaces.

NOTE: On a recessed wall pocket installation, discard ﬁreboard nailing ﬂange leaving ﬁreplace top spacers and heatshield (see Figure 8).

Header may be in direct contact with the ﬁreplace top spacers and heatshield maintaining the 7-1/2” clearance to the ﬁreplace top.

SuperiorFireplaces.us.com 901077-00D14

FRAMING AND FINISHING Continued

Figure 6

Television (TV)

Fireplace

Ceiling

Wall

HeatFlo

Vent

Opening

Min. 76”

(1.930 m)

Max. 20 ft.

(6.096 m)

Secure Nailing

ﬂanges to

Framing

Secure

Fireboard Nailing

Flange(Front and

Inside Framing)

(A) TV Above ﬁre-

place Opening

12” (305 mm)

(B) TV Below Vent

Opening

3” (77 mm)

Below Ceiling

6” (153 mm)

Figure 5 - Fireplace Framing Dimensions for Flush Wall TV Installation One Sided & See-Thru Application

Minimum Dimensions for

Television (TV) Installed

Above Fireplace (Flush Wall)

Base of

Fireplace

Framing Dimensions with HeatFlo Kit for Flush Wall TV Installation, One Sided & See-Thru Application

A B

D *E *F G H

60” Models

One Sided Framing

74-1/4 (1886) 19-1/2 (496) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 62 (1515) 7-1/2 (191)

See-Thru Framing

74-1/4 (1886) 18-1/2 (470) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 62 (1515) 7-1/2 (191)

72” Models

One Sided Framing

86-1/4 (2191) 19-1/2 (496) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 78 (1981) 7-1/2 (191)

See-Thru Framing

86-1/4 (2191) 18-1/2 (470) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 78 (1981) 7-1/2 (191)

84” Models

One Sided Framing

98-1/4 (2496) 19-1/2 (496) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 90 (2286) 7-1/2 (191)

See-Thru Framing

98-1/4 (2496) 18-1/2 (470) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 90 (2286) 7-1/2 (191)

•

Optional HeatFlo Kit required to install TV above appliance

• Optional See-Thru Kit required for See-Thru installation

*E. Minimum height from appliance base to ceiling

*F. Minimum distance from framed opening to ceiling

Inches (millimeters)

SuperiorFireplaces.us.com901077-00D 15

(A) Pocket Above Fireplace Opening (Min.) 18” (457 mm)

(B) Pocket Below Fireplace Opening (Min.) 5-1/2” (140 mm)

* NOTE: Maximum pocket depth is 3-1/2” (89 mm)

FRAMING AND FINISHING Continued

Figure 9 - Dimensions for Television (TV) Installed

Above Fireplace on a Recessed Wall Pocket

Figure 7 - Fireplace Framing Dimensions for Recessed Wall Pocket TV Installation One Sided & See-Thru Application

Television (TV)

Fireplace

Ceiling

Wall

HeatFlo

Vent

Opening

Min. 76”

(1.930 m)

Max. 20 ft.

(6.096 m)

3" Min.

(All Sides)

Pocket

Figure 8 - Removing Fireboard Nailing Flange for Recessed

Wall Pocket Installation

Fireplace Framing Recessed Wall Pocket & HeatFlo Kit

(For TV Installation)

NOTE: Remove Fireboard Nailing Flange for recessed installation (Figure 8).

"Wood Header

(ﬁreboard

nailing ﬂange

removed)

Secure Nailing

Flanges to

Framing

Framing Dimensions with HeatFlo Kit for Recessed Wall Pocket TV Installation One Sided & See-Thru Application - Inches (millimeters)

A B

*D *E *F G H

60” Models

One Sided Framing

74-1/4 (1886) 19-1/2 (496) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 62 (1515) 7-1/2 (191)

See-Thru Framing

74-1/4 (1886) 18-1/2 (470) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 62 (1515) 7-1/2 (191)

72” Models

One Sided Framing

86-1/4 (2191) 19-1/2 (496) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 78 (1981) 7-1/2 (191)

See-Thru Framing

86-1/4 (2191) 18-1/2 (470) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 78 (1981) 7-1/2 (191)

84” Models

One Sided Framing

98-1/4 (2496) 19-1/2 (496) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 90 (2286) 7-1/2 (191)

See-Thru Framing

98-1/4 (2496) 18-1/2 (470) 48-1/2 (1232) 44-3/4 (1137) 3-1/2 (89) 84 (2134) 3 (76) 90 (2286) 7-1/2 (191)

•

Optional HeatFlo Kit required to install TV above appliance

• Optional See-Thru Kit required for See-Thru installation

*D Maximum allowable depth

*E. Minimum height from appliance base to ceiling

*F. Minimum distance from framed opening to ceiling

Base of

Fireplace

SuperiorFireplaces.us.com 901077-00D16

FRAMING AND FINISHING Continued

NOTE: Back wall of chase/

enclosure (including ﬁnishing

materials) shown.

7 (178)

Figure 10 - Fireplace Framing Speciﬁcations - Corner Installation with Horizontal termination

Figure 11 - Fireplace Dimensions

Inches (millimeters)

Fireplace Framing Speciﬁcations -Corner Installation

with Horizontal termination

Model A B C D E F

60”

74-1/4

(1886)

111-7/8"

(2842)

79-1/8

(2010)

(1422)

(838)

(26)

72"

86-1/4

(2191)

123-7/8

(3146)

87-5/8

(2226)

(1575)

37-1/4

(946)

(26)

84"

98-1/4

(2496)

135-7/8

(3451)

96-1/8

(2442)

(1727)

41-1/2

(1054)

(26)

TOP VIEW

FRONT VIEW

SIDE VIEW

48-1/4

(1226)

(533)

9-1/2

(241)

15-5/8

(397)

61-1/2

(1562)

76-5/8

(1946

)

56-5/8

(1438)

37-1/2

(953)

40-3/8

(1026)

44-3/4

(1137)

Fireboard

Nailing Flange

18-5/8 (473)

20-1/8 (511)

3/4

(19)

7/8

(22)

48-1/4

(1226)

(533)

9-1/2

(241)

15-5/8

(397)

44-3/4

(1137)

40-3/8

(1026)

37-1/2

(953)

GAS LINE

CONNECTION

FIREBOARD

NAILING FLANGE

9-1/4

235

9-1/4

(235)

Fireplace Dimensions

Model A B C D E

60”

(1880)

(940)

56-5/8

(1438)

61-1/2

(1562)

76-5/8

(1946)

72"

(2184)

(1092)

68-5/8

(1743)

73-1/2

(1867)

88-5/8

(2251)

84"

(2489)

(1245)

80-5/8

(2048)

85-1/2

(2172)

100-5/8

(2556)

SuperiorFireplaces.us.com901077-00D 17

TERMINATION LOCATION AND CLEARANCES

Table 2 - Horizontal vent termination clearances for buildings with combustible and noncombustible exteriors

Fixed

Closed

Openable

Fixed

Closed

TERMINATION CAP

AIR SUPPLY INLET

GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

Openable

See Table 3

Inside Corner

Outside Corner Recessed Location

Balcony with No Side

Wall

Balcony with Perpendicular Side Wall

U.S. Installation ** Canadian Installation *

A Clearance above grade, veranda, porch, desk, or balcony 12” (300 mm) ** 12” (300 mm) *

B Clearance to window or door that may be opened 6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

9” (230 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW), and < 50,000 Btu/h (15

kW),

12” (300 mm)

for ﬁreplaces > 50,000 Btu/h (15 kW) **

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

12” (300 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW)

C Clearance to permanently closed window 9” (229 mm)

recommended to prevent window condensation

12” (305 mm)

recommended to prevent window

condensation

D Vertical clearance to ventilated sofﬁt located above the

termination within a horizontal distance of 18” (458 mm)

18” (458 mm) 18” (458 mm)

E Clearance to unventilated sofﬁt 12” (305 mm)

30” (760 mm) to vinyl sofﬁt

12” (305 mm)

30” (760 mm) to vinyl sofﬁt

F Clearance to outside corner 5” (127 mm)

minimum

5” (127 mm)

minimum

G Clearance to inside corner 2” (51 mm) minimum 2” (51 mm) minimum

H Clearance to each inside of center line extended above

meter / regulator assembly

36” (910 mm)

within a height of 15 ft above the meter / regulator assembly **

36” (910 mm)

within a height of 15 ft above the meter /

regulator assembly *

I Clearance to service regulator vent outlet 36” (910 mm)** 36” (910 mm)*

J Clearance to nonmechanical air supply inlet to building or

the combustion air inlet to any other ﬁreplace

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

9” (230 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW) and < 50,000 Btu/h (15 kW),

12” (300 mm)

for ﬁreplaces > 50,000 Btu/h (15 kW)**

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

12” (300 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW)

K Clearance to a mechanical air supply inlet 36” (910 mm) above if within 10 ft (3 m) horizontally ** 72” (1830 mm) *

L Clearance above paved sidewalk or paved driveway located

on public property

84” (2130 mm) ‡ 84” (2130 mm) ‡

M Clearance under veranda, porch, deck or balcony 12” (300 mm) *‡ 12” (300 mm) *‡

N Depth of alcove (maximum) 72” (1830 mm) ** 72” (1830 mm) *

O Clearance to termination (alcove) 6” (15.2 mm) ** 6” (15.2 mm)*

P Width of alcove (minimum) 36” (910 mm) ** 36” (910 mm) *

Q Clearance to combustible above (alcove) 18” (457 mm) ** 18” (457 mm) *

‡

*‡

In accordance with the current CAN/CGA-B149.1 National Gas And Propane Installation Code

In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings

Only permitted if veranda, porch, deck, or balcony is fully-open on a minimum two sides beneath the ﬂoor

SuperiorFireplaces.us.com 901077-00D18

VENTING INSTALLATION

These ﬁreplaces are tested and approved for use with IHP 6DVL

Direct Vent Pipe components and terminations.

The venting system must terminate on the outside of the structure

and can not be attached to a chimney or ﬂue system serving a sepa-

rate solid fuel or gas burning appliance. A direct vent appliance must

have its own venting system. DO NOT common vent this appliance.

These models are approved to be vented either horizontally through

an outside wall or vertically through a roof or chase enclosure using

the following guidelines:

• When venting system terminates horizontally on an outside wall,

you may install a standoff if the termination cap is to be installed

directly on a combustible ﬁnish such as vinyl, wood, stucco, etc.

• Never run the vent downward as this may cause excessive tem-

peratures which could cause a ﬁre.

• Vent pipe air space clearances to combustibles are 1" on all sides

except on the horizontal sections, which requires 3" clearance

from the top of the pipe including horizontal terminal.

• Have ﬁreplace and selected vent components on hand to help

determine the exact measurements when elbowing or offsetting.

Always use wall ﬁrestops when penetrating walls and ﬁrestops

when penetrating ceilings or attic spaces.

INSTALLATION PRECAUTIONS

• Wear gloves and safety glasses for protection

• Use extreme caution when using ladders or when on roof tops

• Be aware of electrical wiring locations in walls and ceilings

WARNING

Read all instructions completely and thoroughly

before attempting installation. Failure to do so

could result in serious injury, property damage or

loss of life.

WARNING

This gas ﬁreplace and vent assembly must be vented

directly to the outside. The venting system must

NEVER be attached to a chimney serving a separate

solid fuel burning appliance. Each direct vent gas

appliance must use a separate vent system. Do not

use common vent systems.

NOTICE

Read these instructions completely before

attempting installation.

NOTICE

Failure to follow these instructions will void the

warranty

NOTICE

Do not seal termination cap to vent pipe. Cap must

be removable for vent inspection and maintenance.

The following actions will void the warranty on your venting

system:

• Installation of any damaged venting component

• Unauthorized modiﬁcation of the venting system (Do not cut or alter

vent components)

• Installation of any component part not manufactured or approved

by INNOVATIVE HEARTH PRODUCTS

• Installation other than as instructed by these instructions

VENT INSTALLATION PLANNING

There are two basic types of direct vent installation:

• Horizontal Termination

• Vertical Termination

Horizontal Termination Installation

IMPORTANT: Horizontal terminations require only inner portion of

wall ﬁrestop.

1. Set ﬁreplace in its desired location and determine the route your

horizontal venting will take. Do not secure ﬁreplace until all vent-

ing has been installed. Some installations require sliding ﬁreplace

in and out of position to make ﬁnal venting connections. Figures

15-16 on Page 20 show different conﬁgurations for venting with

horizontal termination that will help you decide which application

best suits your installation. Check to see if wall studs or roof

rafters are in the path of your desired venting route. If they are,

you may want to adjust location of ﬁreplace.

2. Direct vent pipe sections and components are designed with

special twist-lock connections.

Twist-Lock Procedure: Female ends of pipes have locking lugs

(indentations). These lugs will slide straight into matching slots

on male ends of adjacent pipes. Push pipe sections together and

twist one section clockwise approximately one-quarter turn until

sections are fully locked (see Figure 12, Page 19).

NOTE: Horizontal vent must be sloped to 1/4” per foot rise from

inlet to termination. Use non-combustible hanger straps (such

as plumbers tape) to support horizontal sections every 4 feet.

Pipe must not sag.

3. Assemble desired combination of pipe and elbows to ﬁreplace ﬂue

collar. If there are long portions of venting run, pre-assembled

pipe sections may be installed as subassemblies for convenience.

WARNING

Vent pipe air space clearances to combustibles

are 1" on all sides except on horizontal sections,

which require 3" clearances from the top of the

pipe including the horizontal terminal. Where the

Vertical termination cap penetrates a combustible

space, 1" air space clearance is required.

SuperiorFireplaces.us.com901077-00D 19

(Framing

Detail)

13"

13" Inside Framing

13"

Vent Opening

Combustible Wall

Vent Opening

Noncombustible Wall

4. Carefully determine location where vent pipe assembly will pen-

etrate outside wall. Mark center line of pipe on wall. Mark wall

for a 13" x 11" square hole, where bottom of square starts 5-1/2"

below center line of pipe (see Figure 13). This will provide the

3" minimum spacing needed on top of horizontal pipe. Cut and

frame 13" x 11" rectangular hole in exterior wall where vent will

be terminated. If wall being penetrated is constructed of noncom-

bustible material, such as masonry block or concrete, a 9-1/2"

hole with zero clearance is acceptable (see Figure 13).

Figure 12 - Vent Pipe Connections

Female Locking Lugs

Male Slots

Figure 13 - Vent Opening Requirements

VENTING INSTALLATION Continued

Figure 14 - Installing Horizontal Vent Cap

(Noncombustible Exterior)

Wood

Screw

Vent Cap

Apply Mastic

to All Four

Sides

5. Noncombustible Exterior Wall: Position horizontal vent cap in

center of the 9-1/2" round hole and attach to exterior wall with

four fasteners. Before attaching vent cap to exterior wall, run a

bead of non-hardening mastic (pliable sealant) around outside

edges to make a seal between it and outside wall.

NOTE: Use the appropriate type fasteners for stucco, brick,

concrete or other types of sidings (see Figure 14).

Combustible Exterior Wall: A combustible siding standoff is

required when terminating thru combustible siding materials.

For vinyl siding, stucco or wood exteriors, a siding standoff may

be installed between the vent cap and the exterior wall. Siding

standoff prevents excessive heat from damaging siding materials.

Siding material must be cut to accommodate standoff. Fasten

vent cap to standoff. Apply non-hardening mastic around outside

edge of standoff. Position standoff/cap assembly over the 13" x

11" rectangular hole and attach to exterior wall with appropriate

type fasteners for wall material (see Figure 15A, Page 20). Siding

standoff must sit ﬂush against exterior fascia material.

6. Connecting Vent Cap with Horizontal Vent Pipe: Slide wall

ﬁrestop over vent pipe before connecting horizontal run to vent

cap (see Figure 15B, Page 20).

Carefully move ﬁreplace, with vent assembly attached, toward

wall and insert vent pipe into horizontal termination. Pipe overlap

should be a minimum of 1-1/4" (see Figure 16, Page 20).

Slide wall ﬁrestop against interior wall surface and attach with

screws. See Figure 16, Page 20 for horizontal termination details.

Place ﬁreplace into position and shim with noncombustible ma-

terial if needed. Nail or screw side ﬂanges to framing to secure

unit in place. IMPORTANT: Make sure ﬁreplace is level before

securing. If ﬁreplace is not level it will not work properly.

WARNING

Do not recess vent termination into any wall. This

will cause a ﬁre hazard.

Center

of Hole

11" Inside Framing

13"

11"

SuperiorFireplaces.us.com 901077-00D20

VENTING INSTALLATION Continued

Figure 15A - Installing Siding Standoff (Combustible

Exterior Wall)

Figure 15B - Connecting Vent Cap with Horizontal Vent Pipe

Vent Cap

(Horizontal

Termination)

Interior Wall

Surface

Wall

Firestop

Horizontal Vent

Pipe

Screw

NOTICE

Do not seal termination cap to vent pipe. Cap must

be removable for vent inspection and maintenance.

WARNING

Never run vent downward as this may cause

excessive temperatures which could cause a ﬁre.

Operation of improperly installed and maintained

venting system could result in serious injury,

property damage or loss of life.

Horizontal Termination Conﬁgurations

Figures 18-19, Page 22, show the conﬁgurations for venting with

horizontal termination with critical minimum and maximum dimen-

sions which MUST be met.

Cut Siding Away to Fit

Standoff

Wood

Screw

Screws

Standoff

Vent Cap

Apply Mastic

to All Four Sides

Figure 16 - Typical Horizontal Termination Cap Mounting

with Additional Siding Standoff Installed

Siding

Standoff

Screws

Horizontal

Termination

Apply

Mastic to

Outside

Edge of

Standoff

Exterior Wall with Vinyl Siding

13" x 11" Framed

Opening

Maintain 1" at

Bottom and sides,

3" at top Minimum

Air Space Around

Outer Pipe When

Penetrating a Wall

Minimum

Pipe

Overlap

1-1/4"

Wall

Firestop

Direct

Vent

Pipe

La page charge ...

Superior Fireplaces DRL6000 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRL6000

Catégorie: Poêles

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Superior Fireplaces DRL6000 Operating instructions

Superior Fireplaces DRL6000 Mode d'emploi

Superior Fireplaces DRL6000 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents