Samsung ME179KFETSR Guide d'installation
- Catégorie
- Hottes
- Taper
- Guide d'installation
Ce manuel convient également à
Installation Instructions
Over The Range Microwave Oven
BEFORE YOU BEGIN (Read these instructions completely and carefully.)
IMPORTANT
Save these instructions for local inspector’s use.
IMPORTANT
Observe all governing codes and ordinances.
• Note to Installer - Be sure to leave these instructions with the Consumer.
• Note to Consumer - Keep these instructions for future reference.
• Skill level - Installation of this appliance requires basic mechanical and electrical
skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 1 2017-11-02 2:47:00
2
Contents
1. Placement of the mounting plate . . . . 8
A. Removing the microwave oven from the
carton/Removing the mounting plate . . 8
B. Finding the wall studs. . . . . . . . . . . 8
C. Determining wall plate location under your
cabinet . . . . . . . . . . . . . . . . . . 9
D. Aligning the wall plate. . . . . . . . . . 10
2. Ventilation types (choose a, b or c) . . . 11
A. Outside top exhaust (vertical duct). . . 12
A1. Installation procedure for exhaust
adaptor and proper damper operation
check . . . . . . . . . . . . . . . . 12
A2. Adjust the exhaust adaptor . . . . 12
B. Recirculating (non-vented ductless) . . 12
B1. Adapting the microwave blower for
recirculation . . . . . . . . . . . . 12
B2. Installing the charcoal filter . . . . 13
C. Outside back exhaust (horizontal duct) 14
C1. Adapting the microwave blower for
outside back exhaust . . . . . . . 14
3. Installation . . . . . . . . . . . . . . . . 15
A. Preparing the rear wall for outside back
exhaust . . . . . . . . . . . . . . . . . 15
B. Attach the mounting plate to the wall . 15
C. Use the top cabinet template to prepare
the top cabinet . . . . . . . . . . . . . 16
D. Mount the microwave oven . . . . . . . 16
E. Connecting ductwork for outside top
exhaust . . . . . . . . . . . . . . . . . 17
4. Before you use your microwave . . . . 18
Step-by-step installation guide
Important safety instructions . . . . . . . 3
Electrical requirements . . . . . . . . . . 3
Hood exhaust . . . . . . . . . . . . . . . . 4
Damage - Shipment/Installation. . . . . . 6
Parts included . . . . . . . . . . . . . . . 6
Tools you will need . . . . . . . . . . . . . 7
Mounting space. . . . . . . . . . . . . . . 7
General information
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 2 2017-11-02 2:47:01
3
General information
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-prong grounded
outlet. The installer must perform a ground
continuity check on the power outlet box before
beginning the installation to insure that the
outlet box is properly grounded. If not properly
grounded, or if the outlet box does not meet
electrical requirements noted (under ELECTRICAL
REQUIREMENTS), a qualified electrician should be
employed to correct any deficiencies.
Insure proper
ground exists
before use
CAUTION: For personal
safety, remove house
fuse or open circuit
breaker before
beginning installation
to avoid severe or fatal
shock injury.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load and the added weight of this 69
pound product, plus additional oven loads
of up to 50 pounds or a total weight of 119
pounds.
CAUTION: For personal safety, this product
cannot be installed in cabinet arrangements
such as an island or a peninsula. It must be
mounted to BOTH a top cabinet AND a wall.
NOTE: For easier installation and personal
safety, it is recommended that two people
install this product.
IMPORTANT – PLEASE READ CAREFULLY.
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED TO AVOID
SEVERE OR FATAL SHOCK.
Insure proper
ground exists
before use
Insure proper
ground exists
before use.
The power cord of this
appliance is equipped
with a three-prong
(grounding) plug which
mates with a standard
three-prong (grounding)
wall receptacle to
minimize the possibility
of electric shock hazard
from this appliance.
You should have the wall receptacle and circuit
checked by a qualified electrician to make sure
the receptacle is properly grounded.
If you have a standard two-prong wall
receptacle, it is very important to have it
replaced with a properly grounded three-
prong wall receptacle, installed by a qualified
electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
ELECTRICAL
REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 13 amps
and 1.5 kilowatts.This product must be connected to
a supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code
for this kilowatt rating. The power supply cord and
plug should be brought to a separate branch circuit
single grounded outlet of at least 15 A and max
of 20 A. The outlet box should be located in the
cabinet above the microwave oven. The outlet box
and supply circuit should be installed by a qualified
electrician and conform to the National Electrical
Code or the prevailing local code.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 3 2017-11-02 2:47:01
4
General information
NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to
recirculate the air back into the room, proceed to page 11.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart contains an example of one possible ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH
x
NUMBER
USED
=
EQUIVALENT
LENGTH
Roof Cap 24 ft. x (1) = 24 ft.
12 Ft. Straight Duct
(6˝ Round)
12 ft. x (1) = 12 ft.
Rectangular-to-
Round Transition
Adaptor*
5 ft. x (1) = 5 ft.
Equivalent lengths of duct pieces are based on actual tests
and reflect requirements for good venting performance with
any vent hood.
Total Length = 41 ft.
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have to be
cut to fit, using the tin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart contains an example of one possible ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH
x
NUMBER
USED
=
EQUIVALENT
LENGTH
Wall Cap 40 ft. x (1) = 40 ft.
3 Ft. Straight Duct (3 ¼˝
x 10˝ Rectangular)
3 ft. x (1) = 3 ft.
90 ° Elbow 10 ft. x (2) = 20 ft.
Equivalent lengths of duct pieces are based on actual tests
and reflect requirements for good venting performance with
any vent hood.
Total Length = 63 ft.
NOTE: For back exhaust, care should be taken to align the exhaust with the space between studs, or the wall should be
prepared at the time it is constructed by leaving enough space between the wall studs to accommodate the exhaust duct.
HOOD EXHAUST
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 4 2017-11-02 2:47:01
5
General information
Outside ventilation requires a HOOD EXHAUST DUCT.
Read the following carefully.
NOTE: It is important that venting be installed using
the most direct route and with as few elbows as
possible. This ensures clear venting of exhaust and
helps prevent blockages. Also, make sure dampers
swing freely and nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with a
standard 3 ¼˝ x 10˝ rectangular duct.
If a round duct is required, a rectangular-to-round
transition adaptor must be used. Do not use less
than a 6˝ diameter duct.
Maximum duct length:
For satisfactory air movement, the total duct length of
3 ¼˝ x 10˝ rectangular or 6˝ diameter round duct should
not exceed 140 equivalent feet.
Elbows, transitions, wall and roof
caps, etc., present additional resistance to airflow
and are equivalent to a section of straight duct which is
longer than their actual physical size. When calculating
the total duct length, add the equivalent lengths of all
transitions and adaptors plus the length of all straight
duct sections. The chart below shows you how to
calculate total equivalent ductwork length using the
equivalent length in feet of some typical ducts.
DUCT PIECES
EQUIVALENT
LENGTH
x
NUMBER
USED
=
EQUIVALENT
LENGTH
Rectangular-to-Round
Transition Adaptor*
5 ft. x ( ) = ft.
Wall Cap 40 ft. x ( ) = ft.
90 ° Elbow 10 ft. x ( ) = ft.
45 ° Elbow 5 ft. x ( ) = ft.
90 ° Elbow 25 ft. x ( ) = ft.
45 ° Elbow 5 ft. x ( ) = ft.
Roof Cap 24 ft. x ( ) = ft.
Straight Duct 6˝ Round or 3 ¼˝
x 10˝ Rectangular
1 ft. x ( ) = ft.
Total Ductwork = ft.
* IMPORTANT: If a rectangular-to-round
transition adaptor is used, the bottom
corners of the damper will have to be cut
to fit, using tin snips, in order to allow free
movement of the damper.
Equivalent lengths of duct pieces
are based on actual tests and reflect
the requirements for good venting
performance with any vent hood.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 5 2017-11-02 2:47:01
6
General information
• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or
replacement.
• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by
arrangement between the customer and installer.
DAMAGE - SHIPMENT/INSTALLATION
HARDWARE PACKET
PART QUANTITY
Template
INSTALLATION
INSTRUCTIONS
Wood Screws
(¼˝ x 2˝)
1
Template
INSTALLATION
INSTRUCTIONS
Toggle Bolts
(and wing nuts)
(
3
/
16
˝ x 3˝)
3
Template
INSTALLATION
INSTRUCTIONS
Self-aligning
Machine Screws
(¼˝ - 28 x 3 ¼˝)
3
You will find the installation hardware contained in a
packet with the unit. Check to make sure you have all
these parts.
NOTE: Some extra parts are included.
ADDITIONAL PARTS
PART QUANTITY
TOP CABINET TEMPLATE
REAR WALL TEMPLATE
Top Cabinet
Template
1
TOP CABINET TEMPLATE
REAR WALL TEMPLATE
Rear Wall Template 1
Installation
Instructions
1
Template
INSTALLATION
INSTRUCTIONS
Exhaust adaptor 1
GREASE FILTER
You can find the grease filter that is installed on the
product or just packed with the product. Please check
the shape of your grease filter and install the grease
filter on your product correctly.
PART QUANTITY
One Touch Easy
Grease Filter
1
(Installed)
Model : MC17F808KDT
Separately Packed
Grease Filters
2
Model :
MC17J8100CS, MC17J8000CS
PARTS INCLUDED
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 6 2017-11-02 2:47:01
7
General information
# 1 and #2 Phillips
screwdriver
Pencil Ruler or tape measure and
straight edge
Carpenter square (optional)
Tin snips (for cutting
damper, if required)
Scissors (to cut
template, if necessary)
Electric drill with
3
/
16
˝, ½˝ and
⅝˝ drill bits
Filler blocks or scrap wood
pieces, if needed for top
cabinet spacing (used on
recessed bottom cabinet
installations only)
Gloves Saw (saber, hole or
keyhole)
Stud finder or Hammer
(optional)
Safety goggles
Level Duct and masking tape
TOOLS YOU WILL NEED
16 ½˝
30˝
5˝
30˝ min.
Bottom edge of the
cabinet needs to be 30˝
or more from the cooking
surface.
Backsplash
NOTES:
• The space between the cabinets must be 30˝ wide and
free of obstructions.
• This microwave oven is for installation over ranges up
to 36˝ wide.
• If you are going to vent your microwave oven to the
outside, see the Hood Exhaust Section for exhaust
duct preparation.
• If installing the microwave oven beneath smooth
flat cabinets, be careful to follow the instructions
on the top cabinet template for power cord
clearance.
• Maximum cabinet depth above and beside the
unit is 12˝.
• The dimensions provided are the minimum
required for mounting the microwave oven. Local
codes and the practical use of the range will
likely require you to provide more than the 13.5˝
shown between the range and the bottom of the
microwave.
MOUNTING SPACE
12˝ max.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 7 2017-11-02 2:47:02
8
Step-by-step installation guide
1. PLACEMENT OF THE MOUNTING PLATE
A. REMOVING THE
MICROWAVE OVEN FROM
THE CARTON/REMOVING
THE MOUNTING PLATE
1. Remove the installation instructions, Exhaust
adaptor, filters, glass tray, and the small
hardware bag. Do not remove the Styrofoam
protecting the front of the oven.
2. Fold back all 4 carton flaps fully against carton
sides. Then carefully roll the oven and carton
over onto the top side. The oven should be
resting in the Styrofoam.
Styrofoam
Carton
Carton
Styrofoam
3. Pull the carton up and o the oven.
4. Remove and properly discard plastic bags.
Screws
Screws
Mounting Plate
Screws
Mounting Plate
Screws
5. Remove the 2 screws from the mounting plate.
This plate will be used as the rear wall template
and for mounting.
6. Replace the two screws you removed and
carefully screw them back into the case. DO
NOT OVER-TIGHTEN. If you over-tighten the
screws, you can strip the screws and damage
the case.
B. FINDING THE WALL STUDS
Wall Studs
Center
Center
Wall Studs
1. Find the studs using one of the following
methods:
A. Stud finder–a magnetic device which locates
nails.
OR
B. Use a hammer to tap lightly across the
mounting surface to find a solid sound. This
will indicate a stud location.
2. After locating the stud(s), find the stud’s center
by probing the wall with a small nail to find the
edges of the stud. Then, place a mark halfway
between the edges. The center of any adjacent
studs should be 16˝ or 24˝ from this mark.
3. Draw a line down the center of the studs.
THE MICROWAVE MUST BE CONNECTED TO
AT LEAST ONE WALL STUD.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 8 2017-11-02 2:47:02
9
Step-by-step installation guide
C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
C
L
Plate position – beneath flat bottom cabinet.
Draw a vertical line on the
wall at the center of the 30˝
wide space. Tape the Rear
Wall Template onto the wall
so that the top of the template
touches the bottom of the
cabinet and the centerline on
the template lines up with the
line you drew on the wall.
At least 30˝
16 ½˝
C
L
Plate position – beneath framed recessed cabinet
bottom.
30˝ to Cooktop
Draw a vertical line on the wall at the center of the 30˝ wide
space. Tape the Rear Wall Template onto the wall so that the
top of the template touches the bottom of the cabinet frame
and the centerline on the template lines up with the line you
drew on the wall.
C
L
Plate position – beneath recessed bottom
cabinet with front overhang
Draw a line on the
back wall equal to the
depth of the front
overhang.
30" to Cooktop
Plate position – beneath recessed bottom cabinet with
front overhang.
30˝ to Cooktop
Draw a horizontal line to
mark how far the inside
of the front overhang
descends below the
cabinet.
Your cabinets may have decorative trim that interferes
with the microwave installation. Remove the decorative
trim to install the microwave properly and to make it
level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
Draw a vertical line on the wall at the center of the 30˝
wide space. Draw a second, horizontal line on the wall
below the cabinet to mark how far the inside of the
front overhang descends below the cabinet. Tape the
Rear Wall Template onto the wall so that the top of the
template touches the bottom of the horizontal line and
the centerline on the template lines up with the vertical
line.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 9 2017-11-02 2:47:02
10
Step-by-step installation guide
D. ALIGNING THE WALL PLATE
C
L
CAUTION: Wear gloves to avoid cutting
fingers on sharp edges.
Area E
Hole B
Hole A
Centerline
notches
Draw a Vertical Line
on Wall from Center
of Top Cabinet
Draw a Horizontal line on wall from
bottom of “Rear Wall Template”.
Horizontal Line
Horizontal Line
Draw a Horizontal line on wall from bottom of “Rear
Wall Template”.
Draw a Horizontal line on
the wall along the bottom
of “Rear Wall Template”.
Horizontal Line
Horizontal Line Area E
Centerline
notches
Hole A
Hole B
CAUTION: Wear gloves to avoid cutting fingers
on sharp edges.
1. Draw a Horizontal line on the wall at the
bottom of the “Rear Wall Template”.
2. Drill ⅝˝ holes for toggle bolts in 3 locations
(Hole A, Hole B, Hole C) as shown in the
illustration above. If the location of a hole
lines up with a stud, drill a
3
/
16
˝ hole for a
wood screw. You cannot use a toggle bolt to
attach the wall plate to a stud.
NOTE: DO NOT MOUNT THE PLATE AT
THIS TIME.
3. Holes A, B and C are inside area E. If none
of these holes line up with a stud, find a stud
in area E that lines up with a hole circle in
Area E, and then drill a
3
/
16
˝ hole into it for
a wood screw. You must have at least one
wood screw mounted firmly into a stud to
support the weight of the microwave. Set
the mounting plate aside.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 10 2017-11-02 2:47:02
11
Step-by-step installation guide
2. VENTILATION TYPES (CHOOSE A, B OR C)
This microwave oven is compatible with the following
three types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Recirculating (Non-Vented Ductless)
C. Outside Back Exhaust (Horizontal Duct)
NOTE: This microwave is shipped assembled
for Outside Top Exhaust (except for non-vented
models). An exhaust adaptor is shipped assembled
and attached to the filler-upper. Select the type of
ventilation required for your installation and proceed to
that section.
A. OUTSIDE TOP EXHAUST
(VERTICAL DUCT)
B. RECIRCULATING (NON-
VENTED DUCTLESS)
Adaptor in Place
for Outside
Top Exhaust
Adaptor in Place
for Outside Top
Exhaust
See page 12 See page 13
A Charcoal Filter Accessory Kit is required for the
nonvented exhaust. (See your Owner’s Manual for the
kit number.)
C. OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
See page 14
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 11 2017-11-02 2:47:03
12
Step-by-step installation guide
A. OUTSIDE TOP EXHAUST
(VERTICAL DUCT)
A1. INSTALLATION PROCEDURE FOR
THE EXHAUST ADAPTOR AND
PROPER DAMPER OPERATION
CHECK
The exhaust Adaptor and Damper are
shipped assembled and attached to
the filler-upper.
1. Slide the exhaust adaptor as shown in the
diagram above.
2. Make sure the tape securing the damper is
removed and damper pivots easily before you
mount the microwave.
CAUTION: You will need to make adjustments to
assure proper alignment with your house exhaust
duct after the microwave is installed.
A2. ADJUST THE EXHAUST ADAPTOR
After you have installed the microwave, you will
need to open the top cabinet and adjust the exhaust
adaptor so that you can connect it to the house
duct.
For Front-to-Back
Adjustment, Slide the
Exhaust Adaptor as Needed
Blower Plate
Back of
Microwave
Damper
NOTE: You must attach the house duct to the
exhaust adaptor after installation is complete.
House Duct
House Duct
B. RECIRCULATING (NON-VENTED
DUCTLESS)
B1. ADAPTING THE MICROWAVE
BLOWER FOR RECIRCULATION
2. Lift up the
blower plate.
1. Remove and save the screws
that hold the blower plate to the
microwave.
Back of
Microwave
NOTE: The exhaust adaptor with the damper is not
needed for recirculating models. You may want to
save them for possible future use.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 12 2017-11-02 2:47:03
13
Step-by-step installation guide
3. Remove the screw that holds the blower motor
and carefully pull out the blower unit. The wires
will extend far enough to allow you to adjust the
blower unit.
blower mortor screw
CAUTION: To avoid breaking or cracking the blower
blade, do not touch the blade. Hold the outer case
of the blower when you pull it out or put it back in
place.
4. Roll the blower unit 90 ° so that the fan blade
openings are facing toward the front of the
microwave.
Back of
Microwave
Before Roll
After Roll
Back of
Microwave
5. Place the blower unit back into the opening.
CAUTION: Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
6. Secure the blower unit to the microwave with the
screw.
B2. INSTALLING THE CHARCOAL
FILTER
1. Remove the screws on the top of the grill using a
#1 Phillips screwdriver.
2. Open the door.
3. Remove the grill.
• Push the grill left, and then pull the grill straight
o.
Charcoal filter
4. Install the charocal filter. When properly installed,
the wire mesh of the filter should be visible from
the front.
5. Reinstall the grill and the screws.
6. Close the door.
Insert mesh-side up
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 13 2017-11-02 2:47:03
14
Step-by-step installation guide
C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
C1. ADAPTING THE MICROWAVE
BLOWER FOR OUTSIDE BACK
EXHAUST
1. Remove and save the screws that hold the
Blower Plate to the microwave.
2. Lift up the
Blower plate.
Screw
Blower Motor
Back of Microwave
Blower Plate Screw
3. Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the
blower unit.
BEFORE: Fan Blade
Openings Facing Forward
End B
End A
CAUTION: To avoid breaking or cracking the blower
blade, do not touch the blade. Hold the outer case
of the blower when you pull it out or put it back in
place.
4. Remove Parts “A” with tin snips or pliers.
Parts “A”
5. Rotate the blower unit counterclockwise 180 °.
Before Rotation After Rotation
Back of Microwave
Back of Microwave
6. Place the blower unit back into the opening.
AFTER: Fan Blade Openings
Facing Back
End B
End A
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not
pinched.
NOTE: The blower unit exhaust openings
should match exhaust openings on the rear of
microwave oven.
7. Close the Blower Plate and attach the exhaust
adaptor to the rear of the oven by sliding it into
the guides at the back top center of the oven.
Push in securely until it is in the lower locking
tabs. Take care to ensure that the damper hinge
is installed so that it is at the top and that the
damper swings freely.
Locking Tabs
Adaptor
Guide
Back of
Microwave
Guide
From Blower motor screw
(after attached the exhaust adaptor)
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 14 2017-11-02 2:47:04
15
Step-by-step installation guide
B. ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts. At
least one wood screw must be used to attach the
plate to a wall stud.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through
the holes designated to go into drywall, and
then reattach the toggle wings so that ¾˝ of the
bolt protrudes beyond the wing.
INSTALLATION OVERVIEW
A. Prepare Rear Wall (horizontal duct only)
B. Attach Mounting Plate to Wall
C. Prepare Top Cabinet
D. Mount the Microwave Oven
E. Connecting Ductwork (vertical duct only)
A. PREPARING THE REAR
WALL FOR OUTSIDE BACK
EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
C
L
• Read the instructions for outside back exhaust
on the REAR WALL TEMPLATE.
• Tape the REAR WALL TEMPLATE to the rear
wall.
• Cut the opening, following the instructions on
the REAR WALL TEMPLATE.
CAUTION: Do not cut an opening in the rear wall if
you are installing the microwave with vertical duct or
non-vented ductless ventilation.
3. INSTALLATION
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 15 2017-11-02 2:47:04
16
Step-by-step installation guide
To use toggle bolts:
Wall
Toggle Wings
Toggle
Bolt
Bolt End
Spacing for Toggles More
Than Wall Thickness
Mounting
Plate
Spacing for Toggles More
Than Wall Thickness
Bolt End
Mounting
Plate
Toggle
Bolt
Wall
Toggle Wings
3. Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening the toggle bolts and wood
screw, make sure the bottom of the Mounting plate
runs along the bottom Horizontal line of the “Rear wall
Template” and the Mounting plate is properly centered
under the cabinet.
CAUTION: Be careful to avoid pinching your fingers
between the back of the mounting plate and the wall.
4. Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts. Tighten the screw.
C. USE THE TOP CABINET
TEMPLATE TO PREPARE
THE TOP CABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes in
the cabinet bottom.
D. MOUNT THE MICROWAVE
OVEN
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use the handle
during installation.
NOTE: If your cabinet is metal, use the nylon
grommet in the power cord hole to prevent the cord
from being cut.
NOTE: Filler blocks are required when mounting this
unit under any cabinet with a recessed bottom or
front overhang. (See page 9.)
IMPORTANT: The case damage that will occur
from over tightening screws if you do not use
filler blocks is not covered under warranty.
IMPORTANT: For models with the grease filter
installed, don’t push up on the filter when you
mount the oven.
NOTE: When mounting the microwave oven, thread
the power cord through hole in the bottom of the top
cabinet. Keep it tight throughout Steps 1–3. Do not
pinch the cord or lift the oven by pulling cord.
Grease Filter
Grease Filter
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 16 2017-11-02 2:47:04
17
Step-by-step installation guide
1. Lift the microwave, tilt
it forward, and hook
the slots at the back
bottom edge onto the
four lower tabs of the
mounting plate.
2. Rotate the front of
the oven up against
the cabinet bottom.
3. Insert a self-aligning screw through the top
center cabinet hole. Temporarily secure the oven
by turning the screw at least two full turns after
the threads have engaged. (It will be completely
tightened later.) Be sure to keep the power
cord tight. Be careful not to pinch the cord,
especially when mounting flush to the
bottom of cabinet.
Cabinet Front
Filler Block
Microwave Oven Top
Self-Aligning Screw
Equivalent to
Depth of
Cabinet Recess
Cabinet Bottom Shelf
Equivalent
to Depth of
Cabinet Recess
Cabinet Bottom Shelf
Microwave Oven Top
Cabinet Front
Filler Block
Self-Aligning Screw
4. Attach the microwave oven to the top cabinet.
5. Insert the 2 self-aligning screws through the
cabinet bottom shelf and filler block into the
outer top cabinet of the unit. Continue to
support the unit until both screws are inserted
and engaged at least two full turns, then fully
tighten both screws until the unit is secure.
6. Install the grease filters. See the Owner’s Manual
packed with the microwave for instructions.
NOTE: For models with installed grease filters, you
do not need to install a filter.
E. CONNECTING DUCTWORK
FOR OUTSIDE TOP
EXHAUST
House Duct
House Duct
1. Extend the house duct down to connect to the
exhaust adaptor.
2. Seal the exhaust duct joints using duct tape.
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 17 2017-11-02 2:47:05
18
Before You Use Your Microwave
1. Make sure the microwave oven has been
installed according to instructions.
2. Remove all packing material from the
microwave oven.
3. Install the turntable and ring in cavity.
4. Replace the house fuse or turn the breaker
back on.
Insure proper
ground exists
before use
5. Plug the power cord into a dedicated 15 amp
electrical outlet.
Insure proper
ground exists
before use
Insure proper
ground exists
before use.
6. Read the Owner’s Manual.
7. Keep installation instructions for the local
inspector’s use.
4. BEFORE YOU USE YOUR MICROWAVE
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 18 2017-11-02 2:47:05
19
Memo
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 19 2017-11-02 2:47:05
DE68-04129B-02
Manual-Installation_MC17J8100CS_AC_DE68-04129B-02_EN+CFR.indb 20 2017-11-02 2:47:05
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Samsung ME179KFETSR Guide d'installation
- Catégorie
- Hottes
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Samsung SMH2117S Le manuel du propriétaire
-
Samsung ME21M706BAG/AC Guide d'installation
-
-
-
Samsung 1133098 Guide d'installation
-
Samsung ME17H703SHS/AC Guide d'installation
-
-
-