Samsung BD-J5500 Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Blu-ray
Disc Player
user manual
BD-J5500
ENGLISH
2
Safety Information
Warning
~
The slots and openings in the cabinet and
in the back or bottom are provided for
necessary ventilation. To ensure reliable
operation of this apparatus, and to protect it
from overheating, these slots and openings
must never be blocked or covered.
- Do not place this apparatus in a
confined space, such as a bookcase,
or built-in cabinet, unless proper
ventilation is provided.
- Do not place this apparatus near or
over a radiator or heat register, or
where it is exposed to direct sunlight.
- Do not place vessels (vases etc.)
containing water on this apparatus. A
water spill can cause a fire or electric
shock.
~
Do not expose this apparatus to rain or place
it near water (near a bathtub, washbowl,
kitchen sink, or pool, etc.). If this apparatus
accidentally gets wet, unplug it and contact
an authorized dealer immediately
.
~
This apparatus uses batteries. In your
community, there might be environmental
regulations that require you to dispose of
these batteries properly. Please contact
your local authorities for disposal or
recycling information.
~
Do not overload wall outlets, extension
cords or adaptors beyond their capacity,
since this can result in fire or electric
shock.
~
Route power-supply cords so that they
are not likely to be walked on or pinched
by items placed on or against them. Pay
particular attention to cords at the plug
end, at wall outlets, and the point where
they exit from the apparatus.
~
To protect this apparatus from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug
it from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the set due to lightning and
power line surges.
~
Before connecting the AC power cord
to the DC adaptor outlet, make sure the
voltage designation of the DC adaptor
corresponds to the local electrical supply.
~
Never insert anything metallic into the
open parts of this apparatus. Doing so
may create a danger of electric shock.
~
To avoid electric shock, never touch the
inside of this apparatus. Only a qualified
technician should open this apparatus.
~
Make sure to plug the power cord in until
it is firmly seated. When unplugging the
power cord from a wall outlet, always pull
on the power cord’s plug. Never unplug
by pulling on the power cord. Do not
touch the power cord with wet hands.
~
If this apparatus does not operate
normally - in particular, if there are any
unusual sounds or smells coming from
it - unplug it immediately and contact an
authorized dealer or service center.
~
Maintenance of Cabinet.
- Before connecting other components to
this product, be sure to turn them off.
- If you move your product suddenly
from a cold place to a warm place,
condensation may occur on the
operating parts and lens and cause
abnormal disc playback. If this occurs,
unplug the product, wait for two hours,
and then connect the plug to the
power outlet. Then, insert the disc, and
try to play back again.
~
Be sure to pull the power plug out of the
outlet if the product is to remain unused
or if you are leaving the house for an
extended period of time (especially when
children, elderly, or disabled people will be
left alone in the house).
- Accumulated dust can cause an
electric shock, an electric leakage,
or a fire by causing the power cord
to generate sparks and heat or the
insulation to deteriorate.
~
Contact an authorized service center for
information if you intend to install your
product in a location with heavy dust, high
or low temperatures, high humidity, chemical
substances, or where it will operate 24
hours a day such as in an airport, a train
station, etc. Failing to do so may lead to
serious damage of your product.
~
Use only a properly grounded plug and
wall outlet.
- An improper ground may cause electric
shock or equipment damage. (Class l
Equipment only.)
~
To turn this apparatus off completely, you
must disconnect it from the wall outlet.
Consequently, the wall outlet and power
plug must be readily accessible at all times.
~
Do not allow children to hang on the
product.
~
Store the accessories (battery, etc.) in a
location safely out of the reach of children.
~
Do not install the product in an unstable
location such as a shaky self, a slanted
floor, or a location exposed to vibration.
~
Do not drop or strike the product. If the
product is damaged, disconnect the
power cord and contact a service center.
~
To clean this apparatus, unplug the power
cord from the wall outlet and wipe the
product using a soft, dry cloth. Do not
use any chemicals such as wax, benzene,
alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals
can damage the appearance of the product
or erase the printing on the product.
~
Do not expose this apparatus to dripping
or splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
~
Do not dispose of batteries in a fire.
~
Do not plug multiple electric devices into
the same wall socket. Overloading a socket
can cause it to overheat, resulting in a fire.
~
There is danger of an explosion if you
replace the batteries used in the remote
with the wrong type of battery. Replace
only with the same or equivalent type.
~
WARNING - TO PREVENT
THE SPREAD OF FIRE,
KEEP CANDLES AND
OTHER ITEMS WITH
OPEN FLAMES AWAY
FROM THIS PRODUCT
AT ALL TIMES.
This symbol indicates that
high voltage is present inside.
It is dangerous to make any
kind of contact with any inter-
nal part of this product.
This symbol indicates that
important literature concerning
operation and maintenance has
been included with this product.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL
SERVICING TO QUALIFIED PERSONNEL.
3
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product. Use of controls,
adjustments or performance of procedures
other than those specified herein may result
in hazardous radiation exposure.
CAUTION :
~
THIS PRODUCT USES AN INVISIBLE
LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE
IF DIRECTED. BE SURE TO OPERATE
PRODUCT CORRECTLY AS INSTRUCTED.
~
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVERS
AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
This product satisfies CE regulations
when shielded cables and connectors
are used to connect the unit to other
equipment. To prevent electromagnetic
interference with electric appliances, such
as radios and televisions, use shielded
cables and connectors for connections.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
NOTES
If the Region number of a Blu-ray Disc/DVDs
does not correspond to the Region number of
this product, the product cannot play the disc.
IMPORTANT NOTE
The mains lead on this equipment is supplied
with a molded plug incorporating a fuse. The
value of the fuse is indicated on the pin face of
the plug.
If it requires replacing, a fuse approved to
BS1362 of the same rating must be used.
Never use the plug with the fuse cover
omitted if the cover is detachable. If a
replacement fuse cover is required, it must
be of the same colour as the pin face of the
plug. Replacement covers are available from
your dealer.
If the fitted plug is not suitable for the power
points in your house or the cable is not long
enough to reach a power point, you should
obtain a suitable safety approved extension
lead or consult your dealer for assistance.
However, if there is no alternative to cutting
off the plug, remove the fuse and then safely
dispose of the plug. Do not connect the plug
to a mains jack, as there is a risk of shock
hazard from the bared flexible cord.
To disconnect the apparatus from the mains,
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
readily operable.
The product unit accompanying this user
manual is licenced under certain intellectual
property rights of certain third parties.
Precautions
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below.
Keep these operating instructions handy for
future reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.
Do not use this apparatus near water.
6. Clean only with a dry cloth.
7.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including AV
receivers) that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or
the third prong are provided for your
safety. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where it exits the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only
with the cart,
stand, tripod,
bracket, or table
specified by the
manufacturer,
or sold with the
apparatus. When
a cart is used, use caution when moving
the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as when the power-supply
cord or plug is damaged, liquid has
been spilled or objects have fallen into
the apparatus, the apparatus has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
4
SAFETY INFORMATION
Warning ..................................................... 2
Precautions ............................................... 3
Using the 3D function ................................ 4
GETTING STARTED
Before using the User Manual .................... 5
Logos of Discs the player can play ............5
Accessories ............................................... 7
Front Panel ................................................ 7
Rear Panel .................................................7
Remote Control ......................................... 8
CONNECTIONS
Connecting to a TV ....................................8
Connecting to an Audio System ................9
Connecting to a Network Router ...............9
SETTINGS
The Setup Procedure ............................... 10
Menu Navigation ...................................... 10
Accessing the Settings Menu ..................10
Picture Settings ....................................... 10
Sound Settings ........................................ 12
Network Settings ..................................... 13
System Settings ......................................14
Language Settings ................................... 15
Security Settings......................................15
General Settings ......................................15
Support Settings .....................................15
MEDIA PLAY
Playing a Commercially Recorded Disc ....16
Playing Files on a USB Device ................. 16
Playing a Disc with User Recorded
Content ................................................... 17
Using DLNA ............................................. 17
Controlling Video Playback ...................... 18
Controlling Music Playback ......................18
Playing Photo Contents ........................... 20
APPENDIX
Troubleshooting ....................................... 20
Specifications .......................................... 22
Contents
Using the 3D function
IMPORTANT HEALTH AND SAFETY
INFORMATION FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
~
Some viewers may experience discomfort
while viewing 3D TV such as dizziness,
nausea, and headaches.
If you experience any such symptom,
stop viewing 3D TV, remove the 3D Active
Glasses, and rest.
~
Watching 3D images for an extended
period of time may cause eye strain. If
you feel eye strain, stop viewing 3D TV,
remove your 3D Active Glasses, and rest.
~
A responsible adult should frequently
check on children who are using the 3D
function.
If there are any reports of tired eyes,
headaches, dizziness, or nausea, have
the child stop viewing 3D TV and rest.
~
Do not use the 3D Active Glasses
for other purposes (Such as general
eyeglasses, sunglasses, protective
goggles, etc.).
~
Do not use the 3D function or 3D Active
Glasses while walking or moving around.
Using the 3D function or 3D Active
Glasses while moving around may cause
you to bump into objects, trip, and/or fall,
and cause serious injury.
~
If you want to enjoy 3D content, connect
a 3D device (3D compliant AV receiver or
TV) to the player's HDMI OUT port using
a high-speed HDMI cable. Put on 3D
glasses before playing the 3D content.
~
The player outputs 3D signals only
through HDMI cable connected to the
HDMI OUT port.
~
As the video resolution in 3D play mode
is fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
~
Some functions such as BD Wise,
screen size adjustment, and resolution
adjustment may not operate properly in
3D play mode.
~
You must use a high-speed HDMI cable
for proper output of the 3D signal.
~
Stay at least three times the width of the
screen from the TV when watching 3D
images. For example, if you have a 46-
inch screen, stay 138 inches (11.5 feet)
from the screen.
~
Place the 3D video screen at eye level for
the best 3D picture.
~
When the player is connected to some 3D
devices, the 3D effect may not function
properly.
~
This player does not convert 2D content
into 3D.
~
"Blu-ray 3D" and "Blu-ray 3D" logo
are trademarks of the Blu-ray Disc
Association.
5
Getting Started
Before using the User Manual
Disc Types and Contents your player can play
Media Disc Type Details
VIDEO
Blu-ray Disc
3D Blu-ray Disc
BD-ROM or BD-RE/-R recorded in the BD-RE format.
DVD-VIDEO
DVD-RW
DVD-R
DVD+RW
DVD+R
DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have
been recorded and finalized, or a USB storage media containing DivX,
MKV or MP4 contents.
MUSIC
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing MP3 or WMA contents.
PHOTO
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing JPEG contents.
NOTES
The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.
Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.
Your player will not play content that has been recorded on a BD-R or USB device at a bit rate that
exceeds 25 Mbps.
Playback may not work for some types of discs, or when you use specific functions, such as angle
change and aspect ratio adjustment. Information about the discs is written in detail on the disc box.
Please refer to this if necessary.
When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Disc types your player cannot play
~
HD DVD
~
DVD-ROM/PD/
MV, etc
~
DVD-RAM
~
Super Audio CD
(except CD layer)
~
DVD-RW (VR mode)
~
CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-
Gs play audio only,
not graphics.)
~
3.9 GB DVD-R
for Authoring.
Region Code
Both players and discs are coded by
region.
These regional codes must match for a disc
to play. If the codes do not match, the disc
will not play.
The Region Number for this player is
displayed on the rear panel of the player.
Disc
Type
Region
Code
Area
Blu-ray
Disc
A
North America, Central
America, South America,
Korea, Japan, Taiwan, Hong
Kong and South East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
C
India, China, Russia, Central
and South Asia.
DVD-
VIDEO
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle
East, Egypt, Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America, Central
America, Australia, New Zealand,
Pacific Islands, Caribbean
5
Russia, Eastern Europe, India,
North Korea, Mongolia
6
China
Logos of Discs the player
can play
Blu-ray Disc BD-LIVE
3D Blu-ray Disc DivX
PAL broadcast System in U.K., France, Germany, etc.
Supported File Formats
Notes on the USB connection
~
Y
our player supports USB storage media,
MP3 players, digital cameras, and USB card
readers.
~
The player does not support folder or file
names longer than 128 characters.
~
Some USB/External HDD/digital camera
devices may not be compatible with the
player.
~
Your player supports the FAT16, FAT32, and
NTFS file systems.
~
Connect USB devices directly to the player’s
USB port. Connecting through a USB cable
may cause compatibility problems.
~
Inserting more than one memory device
into a multi-card reader may cause the
reader to operate improperly.
~
The player does not support the PTP
protocol.
6
~
Do not disconnect a USB device during a "loading" process.
~
The bigger the image resolution, the longer the image takes to display.
~
This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from
commercial sites.
~
Your player only supports video with a frame rate under 30fps (frames per second).
~
Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives
and USB HDD. (HUB is not supported.)
~
Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible
with this player.
~
If some USB devices require excessive power, they may be limited by the circuit safety
device.
~
If playback from a USB HDD is unstable, provide additional power by plugging the HDD
into a wall socket.
If the problem continues, contact the USB HDD manufacturer.
~
SAMSUNG is not responsible for any data file damage or data loss.
~
Your player does not support NTFS compressed files, sparse files, or encrypted files.
~
You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)
Video File Support
File Extension Container Video Codec Audio Codec Resolution
*.avi
AVI
DivX 3.11/4/5/6
MP3
Dolby Digital
DTS
WMA
PCM
1920x1080
MP4v3
H.264 BP/MP/HP
1920x1080
*.mkv
MKV
VC-1 AP MP3
Dolby Digital
DTS
1920x1080
H.264 BP/MP/HP
1920x1080
*.wmv
WMV (wmv9)
VC-1 AP
WMA
1920x1080
VC-1 SM
1920x1080
*.mp4
MP4
MP4 (mp4v)
AAC
1920x1080
H.264 BP/MP/HP
1920x1080
*.mpg
*.mpeg
MPEG
MPEG1
MP1, 2
Dolby Digital
DTS
1920x1080
MPEG2
1920x1080
H.264 BP/MP/HP
1920x1080
Limitations
- Even when a file is encoded by a supported codec listed above, the file might not be
played if its content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file
itself is corrupted.
- Files having a higher Bit rate/frame rate than standard may stutter during sound/video
playback.
- The Seek (skip) function is not available if the file’s index table is damaged.
Video decoder
- Supports up to H.264 Level 4.1 and AVCHD
- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4
- MPEG4 SP, ASP :
Below 1280 x 720 : 60 frames max
Above 1280 x 720 : 30 frames max
- Does not support GMC 2 or higher
Audio decoder
- Supports WMA 7, 8, 9 and STD
- Does not support WMA sampling rate of 22050Hz mono.
- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)
Max bit rate: 320kbps
Supported DivX subtitle file formats
*.ttxt, *.smi, *.srt, *.sub, *.txt
NOTES
Playback of some DivX, MKV or MP4 file may not be supported depending on their video resolution and
frame rate.
Music File Support
File
Extension
Container
Audio
Codec
Support Range
*.mp3
MP3 MP3
-
*.wma
WMA WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48
* Bit rates - All bit-rates from 5kbps to 355kbps
7
Picture File Support
File Extension Type Resolution
*.jpg
*.jpeg
*.jpe
JPEG
15360x8640
*.png
PNG
15360x8640
AVCHD (Advanced Video Codec High Definition)
~
This player can play back AVCHD format discs. These discs are normally recorded and
used in camcorders.
~
The AVCHD format is a high definition digital video camera format.
~
The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the
conventional image compressing format.
~
Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs
that use "x.v.Color" format.
~
"x.v.Color" is a trademark of Sony Corporation.
~
"AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.
and Sony Corporation.
NOTES
Some AVCHD format discs may not play, depending on the recording condition.
AVCHD format discs need to be finalized.
"x.v.Color" offers a wider colour range than normal DVD camcorder discs.
Accessories
Check for the supplied accessories shown below.
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
HDMI Cable
Batteries for Remote
Control (AAA Size)
User Manual Remote Control
Front Panel
DISC TRAY
POWER BUTTON
OPEN/CLOSE BUTTON
USB HOST
REMOTE CONTROL SENSOR
NOTES
You can perform software upgrades using the USB Host jack with a USB flash memory stick only.
Please open and pull out the USB cover before inserting USB device.
Rear Panel
HDMI OUT LAN DIGITAL AUDIO OUT
8
Remote Control
Tour of the Remote Control
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
Turn the player on and off.
Allows you to repeat A-B disc.
Press numeric buttons to operate options.
Press to open and close the disc tray.
Use to enter the disc menu.
Press to skip backwards or forwards.
Press to stop a disc.
Press to use Bonusview function.
Return to the previous menu.
These buttons are used both for menus on the
player and also several Blu-ray Disc functions.
Use to select menu items and change menu
values.
Press to use Tools menu.
Use to access various audio functions on a
disc (Blu-ray Disc/DVD).
Press to play a disc.
Press to pause a disc.
Turn the TV on and off.
Press to switch the Blu-ray Disc/DVD's
subtitle language.
Use to enter the popup menu/title menu.
Press to search a disc backwards or
forwards.
Press to move to the home menu.
Press to see the full screen on a TV.
During Blu-ray or DVD disc playback, the
Full screen button does not operate.
Press to exit the menu.
Use to display the playback information.
Allows you to repeat a title, chapter, track or
disc.
TV volume adjustment.
After setup, allows you to set the input
source on your TV.
Installing batteries
NOTES
If the remote does not operate properly:
•
Check the polarity (+/–) of the batteries.
Connections
Connecting to a TV
Connect an HDMI cable from the HDMI OUT jack on the back of the product to
the HDMI IN jack on your TV.
- Do not connect the power cord to the wall outlet until you have made all the
other connections.
- When you change the connections, turn off all devices before you start.
Audio
Video
NOTES
If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital
Audio Out on the player to an audio system to hear audio.
An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of
your TV.
When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the
first time, the player automatically sets the HDMI output resolution to the highest supported by the TV.
A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Colour to Off in the menu.
To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable.
HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on
the screen.
•
Check if the batteries are drained.
•
Check if the remote sensor is blocked by obstacles.
•
Check if there is any fluorescent lighting nearby.
!
CAUTION
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash
Do not dispose of batteries in a fire.
Do not short circuit, disassemble or overheat the batteries.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
9
Connecting to an Audio System
You can connect the Blu-ray player to an audio system using one of the
methods illustrated below.
- Do not connect the power cord to the wall outlet until you have made all the
other connections.
- When you change the connections, turn off all devices before you start.
Method 1 Connecting to an HDMI compatible AV receiver
~
Connect an HDMI cable from the HDMI OUT jack on the back of the product
to the HDMI IN jack on your receiver.
~
Best quality (Recommended)
Method 2 Connecting to an AV receiver with a Digital Coaxial Cable
~
Using a digital Coaxial cable (Not supplied), connect the Coaxial Digital Audio
Out jack on the product to the Digital Coaxial In jack of the receiver.
~
Good quality
~
You will hear sound only through the front two speakers with Digital Output
set to PCM.
AudioAudio
Method 2Method 1
Connecting to a Network Router
You can connect your player to your network router using one of the methods
illustrated below.
To use the DLNA network functionality, you must connect your PC to your
network as shown in the illustration.
Wired Network
Broadband
service
Broadband
service
Broadband modem
(with integrated router)
Broadband
modem
Router
Or
NOTES
Internet access to Samsung's software update server may not be allowed, depending on the router you use or
your ISP's policy. For more information, contact your ISP (Internet Service Provider).
DSL users, please use a router to make a network connection.
10
Settings
The Setup Procedure
~
The Home screen will not appear if you do
not configure the setup.
~
The OSD (On Screen Display) may change
in this player after you upgrade the
software version.
~
The access steps may differ depending on
the menu you selected.
~
After the setup process is complete, the panel
buttons and remote control can be operated.
After you have connected the player
to your TV, turn on the TV and player.
When you turn on the player the first
time, the player's Setup screen appears
on the TV. The Setup procedure lets you
set the On Screen Display (OSD) and
menu languages, the aspect ratio (screen
size), the network type, and connect the
player to your network.
NOTES
The Home menu will not appear if you do not
configure the setup except as noted below.
If you press the BLUE (D) button during
network setup, you can access the Home menu
even if the network setup is not completed yet.
When you return to the Home menu, the full
screen mode is cancelled automatically.
If you want to display the Setup screen again
to make changes, press the
^
button on
the front panel of the player for more than 5
seconds with no disc inserted. This resets the
player to its default settings.
After the setup process is complete. you can
operate the HDMI-CEC function.
If you want to use the Anynet+(HDMI-CEC)
function to aid in the initial set up process,
please follow the instructions below.
1)
Connect the player to an Anynet+(HDMI-CEC)
compliant Samsung TV using HDMI Cable.
2) Set the Anynet+(HDMI-CEC) feature to On
in both the TV and the player.
3) Set the TV to the Setup Procedure.
If you leave the player in the stop mode
for more than 5 minutes without using it,
a screen saver will appear on your TV. If
the player is left in the screen saver mode
for more than 25 minutes, the power will
automatically turn off.
Menu Navigation
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
4
3
1
HOME Button : Press to move to the Home
menu.
2
RETURN Button : Return to the previous menu.
3
v
(Enter) / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
4
EXIT Button : Press to exit the current menu.
Accessing the Settings
Menu
To access the Settings menu and sub-
menus, follow these steps:
1. Press the POWER button.
The Home Menu appears.
2.
Press the ▲▼◄► buttons to select
Settings, and then press the
v
button.
3. Press the ▲▼ buttons to select
the desired submenu, and then
press the
v
button.
4.
Press the ▲▼ buttons to select the
desired item, and then press the
v
button.
5. Press the EXIT button to exit the
menu.
NOTES
The access steps may differ depending on
the menu you selected. The OSD (On Screen
Display) may change in this player after you
upgrade the software version.
Picture Settings
You can configure various display
options such as the TV Aspect Ratio,
Resolution, etc.
3D Settings
Select whether to play a Blu-ray Disc
with 3D contents in 3D Mode.
~
Home Menu
App 1 App 2 App 3 App 4
App 5
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
2
3
6
5
7
1
4
1
Selects VIDEOS.
2
Selects MUSIC.
3
Selects Settings.
4
Selects Change Device.
5
Selects PHOTOS.
6
Selects PLAY DISC.
7
Selects applications.
NOTES
The Videos, Photos, and Music options
require that you have an appropriate disc
inserted into the player or a USB flash device
attached to the player.
11
NOTES
For some 3D discs, to stop a movie during
3D playback, press the
5
button once.
The movie stops and the 3D mode option is
de-activated.
To change a 3D option selection when you are
playing a 3D movie, press the
5
button once.
The Blu-ray menu appears. Press the
5
button again, then select 3D Settings in the
Blu-ray menu.
Depending on the content and the position of the
picture on your TV screen, you may see vertical
black bars on the left side, right side, or both sides.
TV Aspect Ratio
Depending on the type of television
you have, you may want to adjust the
screen size setting.
NOTES
Depending on the disc type, some aspect
ratios may not be available.
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
the picture might appear to be distorted.
BD Wise (Samsung TVs only)
BD Wise is Samsung’s latest inter-
connectivity feature.
When you connect a Samsung player
and a Samsung TV with BD Wise to
each other via HDMI, and BD Wise
is on in both the player and TV, the
player outputs video at the video
resolution and frame rate of the Blu-
ray Disc/DVDs.
NOTES
When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD
Wise appears in the Resolution menu.
If the player is connected to a device that does not
support BD Wise, you cannot use the BD Wise function.
For proper operation of BD Wise, set the BD
Wise menu of both the player and the TV to On.
Resolution
Lets you set the output resolution of
the HDMI video signal to Auto, 1080p,
1080i, 720p or 576p/480p. The number
indicates the number of lines of video
per frame. The i and p indicate interlaced
and progressive scan, respectively. The
more lines, the higher the quality.
Resolution according to the output
mode
~
Blu-ray Disc/E-contents/Digital
Contents playback
Output
Setup
HDMI / connected
HDMI Mode
Blu-ray
Disc
E-contents/
Digital
contents
BD Wise
Resolution of
Blu-ray Disc
1080p
Auto
Max. Resolution
of TV input
Max. Resolution
of TV input
1080p@60F
(Movie Frame : Off)
1080p@60F 1080p@60F
Movie Frame :
Auto (24 fps)
1080p@24F 1080p@24F
1080i 1080i 1080i
720p 720p 720p
576p/480p 576p/480p 576p/480p
~
DVD playback
Output
Setup
HDMI / connected
HDMI Mode
BD Wise 576i/480i
Auto Max. Resolution of TV input
1080p 1080p
1080i 1080i
720p 720p
576p/480p 576p/480p
NOTES
If the TV you connected to the player does
not support Movie Frame or the resolution
you selected, the message "If no pictures are
shown after selecting ‘Yes’, please wait for 15
seconds to return to the previous resolution."
appears. If you select Yes, the TV’s screen
will go blank for 15 seconds, and then the
resolution will revert to the previous resolution
automatically.
If the screen stays blank after you have
changed the resolution, remove all discs,
and then press and hold the
^
button on the
front of the player for more than 5 seconds.
All settings are restored to the factory default.
Follow the steps on the previous page to
access each mode and select the Display
Setup that your TV will support.
When the factory default settings are
restored, all stored user BD data is deleted.
The Blu-ray Disc must have the 24 frame feature for
the player to use the Movie Frame (24 fps) mode.
Movie Frame (24 fps)
Setting the Movie Frame (24 fps)
feature to Auto allows you to adjust
the player’s HDMI output to 24 frames
per second for improved picture
quality.
You can enjoy the Movie Frame (24
fps) feature only on a TV supporting
this frame rate. You can select Movie
Frame only when the player is in the
HDMI 1080p output resolution modes.
HDMI Colour Format
Lets you set the colour space
format for HDMI output to match the
capabilities of the connected device
(TV, monitor, etc).
HDMI Deep Colour
Lets you output video from the HDMI
OUT jack with Deep Colour. Deep
Colour provides more accurate colour
reproduction with greater colour depth.
Progressive Mode
Lets you improve picture quality when
viewing DVDs.
12
Sound Settings
Digital Output
Lets you select the digital audio output format that is suitable for your TV or AV
Receiver. For more details, please refer to the Digital Output Selection table.
Digital Output Selection
Setup PCM
Bitstream
(Unprocessed)
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded
Dolby D)
Connection
HDMI
Receiver
Coaxial
HDMI
Receiver
Coaxial
HDMI Receiver or
Coaxial
HDMI supported
AV receiver or
Coaxial
Audio
Stream on
Blu-ray Disc
PCM Up to 7.1ch PCM 2ch PCM PCM 2ch Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital PCM 2ch PCM 2ch
Dolby
Digital
Dolby
Digital
Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital
Plus
PCM 2ch PCM 2ch
Dolby Digital
Plus
Dolby
Digital
Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby TrueHD PCM 2ch PCM 2ch
Dolby
TrueHD
Dolby
Digital
Re-encoded DTS
Re-encoded
Dolby Digital *
DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD High
Resolution
Audio
PCM 2ch PCM 2ch
DTS-
HD High
Resolution
Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD
Master Audio
PCM 2ch PCM 2ch
DTS-HD
Master
Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
Audio
Stream on
DVD
PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch
Dolby Digital PCM 2ch PCM 2ch
Dolby
Digital
Dolby
Digital
Dolby Digital Dolby Digital
DTS PCM 2ch PCM 2ch DTS DTS DTS DTS
Definition for
Blu-ray Disc
Any
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio and
add Navigation Sound
Effects.
Outputs only main
feature audio stream
so that your AV receiver
can decode the audio
bitstream.
You will not hear
BONUSVIEW audio
and Navigation Sound
Effects.
Decodes main
feature audio and
BONUSVIEW audio
stream together into
PCM audio and add
Navigation Sound
Effects, then re-
encodes the PCM
audio into DTS
bitstream
Decodes main
feature audio and
BONUSVIEW audio
stream together into
PCM audio and add
Navigation Sound
Effects, then re-
encodes the PCM
audio into Dolby
Digital bitstream
* If Source Stream is 2ch, "Re-encoded
Dolby D" Settings are not applied.
Blu-ray Discs may include three audio
streams :
- Main Feature Audio : The audio
soundtrack of the main feature.
- BONUSVIEW audio : An additional
soundtrack such as the director or actor’s
commentary.
- Navigation Sound Effects : When you
choose a menu navigation selection, a
Navigation Sound Effect may sound.
Navigation Sound Effects are different on
each Blu-ray Disc.
NOTES
Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
If the HDMI device (AV receiver, TV) is not
compatible with compressed formats (Dolby
Digital, DTS), the audio signal outputs as PCM.
Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
If your TV is not compatible with compressed
multi-channel formats (Dolby Digital, DTS), the
player may output PCM 2ch downmixed audio
even though you selected Bitstream (either Re-
encoded or Unprocessed) in the setup menu.
If your TV is not compatible with PCM
sampling rates over 48kHz, the player may
output 48kHz downsampled PCM audio even
though you set PCM Downsampling to Off.
PCM Downsampling
Lets you choose to have 96KHz PCM
signals downsampled to 48KHz before
they are outputted to an amplifier.
Choose On if your amplifier or receiver
is not compatible with a 96KHz signal.
Dynamic Range Control
Lets you apply dynamic range control
to Dolby Digital, Dolby Digital Plus,
and Dolby TrueHD audio.
~
Auto : Automatically controls the dynamic
range of Dolby TrueHD audio, based
on information in the Dolby TrueHD
soundtrack.
Also turns dynamic range control on for
Dolby Digital and Dolby Digital Plus.
~
Off :
Leaves the dynamic range
uncompressed, letting you hear the original
sound.
~
On : Turns dynamic range control on for
all three Dolby formats. Quieter sounds
are made louder and the volume of loud
sounds is reduced.
Downmixing Mode
Lets you select the multi-channel
downmix method that is compatible
with your stereo system. You can
choose to have the player downmix
to normal stereo or to surround
compatible stereo.
13
Network Settings
Please contact your ISP to find out if
your IP address is static or dynamic.
If it is dynamic - and most are - we
recommend using the Auto procedure
for network setup. This is easiest and
will work in the majority of cases. If it
is static, you must use the manual set
up procedure.
Network setup directions start below.
NOTES
This unit can only be connected to a Network
via a wired connection.
Wired Network Settings
1. In the Home menu, press the ▲▼
◄► buttons to select Settings,
and then press the
v
button.
2. Press the ▲▼ buttons to select
Network, and then press the
v
button.
3. Press the ▲▼ buttons to select
Wired Network Settings, and
then press the
v
button. The
Wired Network Settings screen
appears.
Picture
Sound
Network
System
Language
Security
General
Support
Settings
Wired Network Settings
Internet Protocol Setup : Auto
\
IP Address :
0
0
0
0
Subnet Mask :
0
0
0
0
Gateway :
0
0
0
0
DNS : Auto
DNS Server :
0
0
0
0
>
Move
"
Select
'
Return
4. In the Internet Protocol Setup field,
select Auto if it is not selected.
(Press
v
select Auto, and then
press
v
.)
5. The Auto Function acquires and
fills in the values for IP Address,
Subnet Mask, etc., automatically.
NOTES
This process can take up to five minutes.
6. After the Network Function has
acquired the network values, press
the RETURN button.
7. Select Network Test, and then
press
v
to ensure the player has
connected to your network.
8. When the Network Test is
complete, press the RETURN
twice to return to the Main Menu.
9. If the Network Function does not
acquire the network values, go to
the directions for Manual Setup.
Manual Network Setup
Before you start manual network setup,
you need the network setting values.
To enter the Network Settings into
your player, follow these steps:
1. In the Home menu, press the ▲▼
◄► buttons to select Settings,
and then press the
v
button.
2. Press the ▲▼ buttons to select
Network, and then press the
v
button.
3. Press the ▲▼ buttons to select
Wired Network Settings, and
then press the
v
button. The
Wired Network Settings screen
appears.
4. Select the Internet Protocol Setup
field, and then press the
v
button.
5. Press the ▲▼ buttons to select
Manual, and then press the
v
button.
6. Press the ▼ button to go to the
first entry field (IP Address).
7. Use the number buttons on your
remote to enter numbers.
8. When done with each field, use
the ► button to move to the next
field. You can also use the other
arrow buttons to move up, down,
and back.
9. Enter the IP Address, Subnet
Mask, and Gateway values in the
same way.
10. Press the ▼ button to go to DNS.
11. Press the ▼ button to go to the
first DNS entry field.
12. Enter the numbers as above.
13. Press the RETURN button on
your remote.
14. Run a Network Test to ensure
the player has connected to your
network.
Network Test
Use this menu item to check whether
your network connection is working or
not.
Network Status
Use to check whether a connection to
a network and the Internet has been
established.
Device Name
Device Name function allows you to
change player's name by selecting
from device name list.
BD-Live Internet Connection
Set to allow or prohibit an Internet
connection when you use the BD-LIVE
service.
~
Allow (All) : The Internet connection
is allowed for all BD-LIVE contents.
~
Allow (Valid Only) : The Internet
connection is allowed only for BD-
LIVE contents containing a valid
certificate.
~
Prohibit : No Internet connection is
allowed for any BD-LIVE content.
14
NOTES
What is a valid certificate?
When the player uses BD-LIVE to send the
disc data and a request to the server to certify
the disc, the server uses the transmitted data
to check if the disc is valid and sends the
certificate back to the player.
The Internet connection may be restricted
while you are using BD-LIVE contents.
Using BD-LIVE™
Once the player is connected to the
network, you can enjoy various movie-
related service contents using a BD-
LIVE compliant disc.
1.
Attach a USB memory stick to
the USB jack on the front of the
player, and then check its remaining
memory. The memory device must
have at least 1GB of free space
to accommodate the BD-LIVE
services.
2. Insert a Blu-ray Disc that supports
BD-LIVE.
3. Select an item from various BD-
LIVE service contents provided by
the disc manufacturer.
NOTES
The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
The DLNA Function
DLNA lets you play music, video, and
photo files located in your PC on the
player.
To use DLNA with your player, you must
connect the player to your network.
(See page 13-14).
To use DLNA with your PC, you must
install DLNA software on your PC.
System Settings
Setup
By using the Setup function, you can
set the language, Network Settings,
etc.
For more information about the Setup
function, refer to the Setup section of
this user manual (See page 10).
Quick Start
You can turn on the power quickly by
decreasing the boot time.
NOTES
If this function is set to On, Standby power
consumption will be increased.
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function
that offers linked operations with
other Samsung players that have the
Anynet+ feature.
To operate this function, connect this
player to an Anynet+ Samsung TV with
an HDMI cable.
With Anynet+ on, you can operate this
player using a Samsung TV remote
control and start disc playback simply
by pressing the PLAY (
) button
on the TV’s remote control.
For more information, please see the
TV user manual.
NOTES
This function is not available if the HDMI
cable does not support CEC.
If your Samsung TV has an Anynet+ logo,
then it supports the Anynet+ function.
Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
After the product was turned off,
disconnecting and connecting the power
cable turns it on automatically. At the moment,
it automatically turns off in about 15 seconds
for re-establishing Anynet+ connection.
For some TV products, if connected to this
product with Anynet+ function, turning the
TV on may display a warning popup message
saying no connection was found. Still,
Anynet+ connection is properly established
and available to use.
BD Data Management
Enables you to manage the
downloaded contents you accessed
through a Blu-ray disc that supports
the BD-LIVE service and stored on a
flash drive.
You can check the device’s information
including the storage size, delete the
BD data, or change the Flash memory
device.
NOTES
In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
Your player supports the FAT16, FAT32, and
NTFS file systems. We recommend you use
USB devices that support USB 2.0 protocol
with 4 MB/sec or faster read/write speed.
The Resume Play function may not work after
you format the storage device.
The total memory available to BD Data
Management may differ, depending on the
conditions.
DivX® Video On Demand
View DivX® VOD Registration Codes
to purchase and play DivX® VOD
contents.
15
Support Settings
Software Upgrade
The Software Upgrade menu allows
you to upgrade the player’s software
for performance improvements or
additional services.
By Online
To upgrade By Online, follow these
steps:
1. In the player’s menu, go to
Settings > Support > Software
Upgrade.
2. Select By Online, and then press
the
v
button. The Connecting to
Server message appears.
3. A popup message will appear if an
update is available.
4. If you select Yes, download
process started. (Never turn the
player on during an upgrade.)
5. When the update is completed,
the player will restart automatically.
NOTES
The upgrade is complete when the player
turns off, and then turns on again by itself.
Never turn the player off or back on manually
during the update process.
Samsung Electronics takes no legal
responsibility for player malfunction caused
by an unstable Internet connection or
consumer negligence during a software
upgrade.
No disc should be in the product when you
upgrade the software By Online.
By USB
To upgrade by USB, follow these
steps:
1. Visit www.samsung.com/
bluraysupport.
2. Download the latest USB software
upgrade zip archive to your
computer.
3. Unzip the zip archive to your
computer. You should have a
single RUF file with the same name
as the zip file.
4. Copy the RUF file to a USB flash
drive.
5. Make sure there is no disc in the
player, and then insert the USB
flash drive into the USB port of the
player.
6. In the player’s menu, go to
Settings > Support > Software
Upgrade.
7. Select By USB.
NOTES
No disc should be in the product when you
upgrade the software using the USB Host
jack.
When the software upgrade is done, check
the software details in the software Upgrade
menu.
Do not turn off the player during the software
upgrade. It may cause the player to malfunction.
Software upgrades using the USB Host jack
must be performed with a USB flash memory
stick only.
Language Settings
You can select the language you
prefer for the On-Screen menu, disc
menu, audio, and subtitles.
NOTES
The selected language will only appear if it is
supported on the disc.
Security Settings
The default security PIN is 0000. Enter
the default PIN to access the security
function if you haven't created your
own PIN. After you have accessed the
security function for the first time, change
the PIN using the Change PIN function.
BD Parental Rating
Prevents playback of Blu-ray Discs
with specific age ratings unless the 4
digit PIN is entered.
DVD Parental Rating
This function works in conjunction with
DVDs that have been assigned an age
rating or numeric rating that indicates
the maturity level of the content. These
numbers help you control the types of
DVDs that your family can watch.
Select the rating level you want to set.
For example, if you select Level 6,
discs rated above 6 - Level 7 and 8 -
will not play.
A larger number indicates more
mature content.
Change PIN
Change the 4-digit password used to
access security functions.
If you forget your password
1. Remove any discs.
2. Press and hold the
^
button on
the front panel for 5 seconds or
more.
All settings will revert to the factory
settings.
NOTES
When the factory default settings are
restored, all the user stored BD data will be
deleted.
General Settings
Time Zone
Lets you specify the time zone that is
applicable to your area.
16
Auto Upgrade Notification
If you have connected the player
to your network, and then set Auto
Upgrade Notification on, the player
automatically notifies you when a new
software version is available for the
player.
To set Auto Upgrade Notification on,
follow these steps:
1. Select Auto Upgrade
Notification, and then press the
v
button.
2. Use the ▲▼ buttons to select On,
and then press the
v
button.
If there is a new software version
available, the player notifies you with a
popup message.
1. To upgrade the firmware, select
Yes in the Pop-up. The player
turns off automatically, then
restarts, and begins the download.
(Never turn the player on or off
manually during an upgrade.)
2. The update progress popup
appears.
3. When the update is completed,
the player will restart automatically.
NOTES
The upgrade is complete when the player
turns off, and then turns on again by itself.
Never turn the player off or on manually
during the update process.
Samsung Electronics takes no legal
responsibility for player malfunction caused
by an unstable Internet connection or
consumer negligence during software
upgrade.
Contact Samsung
Provides contact information for
assistance with your player.
Terms of Service Agreement
Lets you view the general disclaimer
regarding third party contents and
services.
Reset
Returns all settings to their factory
defaults except for the network
settings.
Media Play
Playing a Commercially
Recorded Disc
1. Press the
8
button to open the
disc tray.
2. Place a disc gently into the disc
tray with the disc's label facing up.
3. Press the
8
button to close
the disc tray. Playback starts
automatically.
Playing Files on a USB
Device
There are two methods you can use
to play or view multimedia files located
on a USB device through your player.
Method 1
1. Turn the player on.
2. Connect the USB device to the
USB port on the front panel of the
player. The New Device Connected
pop-up appears.
App 1 App 2 App 3 App 4 App 5
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
New device connected.
Photos
Videos
Music
123
>
Move
"
Enter
'
Return
NOTES
If the pop-up does not appear, go to Method 2.
3. Use the ▲▼ buttons to select
Photos, Videos or Music, and
then press the
v
button. The
Photos, Videos & Music screen
appears listing the content of the
device. Depending on how the
contents is arranged, you will see
either folders, individual files, or
both.
NOTES
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change
this selection by returning to the Photos,
Videos & Music screen and going to Step 3 in
Method 2 below.
4. If necessary, use the ▲▼◄►
buttons to select a folder, and then
press the
v
button.
5. Select a file to view or play, and
then press the
v
button.
6. Press the RETURN button to exit
a folder or the EXIT button to
return to the Home screen.
7. Go to pages 18~20 for instructions
that explain how to control
playback of videos, music, and
pictures on a USB device.
17
Method 2
1. Turn the player on.
2. Connect the USB device to the
USB port on the front panel of the
player. Select Change Device
and then press the ▲▼ button to
select USB. Press the
v
button.
App 1 App 2 App 3 App 4 App 5
Change Device
Settings
PLAY DISC PHOTOS VIDEOS
MUSIC
No Disc
Change Device
No Disc
123
a
Close
3. Use the ▲▼◄► buttons to select
PHOTOS, VIDEOS or MUSIC
on the Home screen, and then
press the
v
button. The Photos,
Videos & Music screen appears
listing the content of the device.
Depending on how the contents
is arranged, you will see either
folders, individual files, or both.
NOTES
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change
this selection by returning to the Photos,
Videos & Music screen and repeating Step 3.
4. If necessary, use the ▲▼◄►
buttons to select a folder, and then
press the
v
button.
5. Use the ▲▼◄► buttons to select
a file to view or play, and then
press the
v
button.
6. Press the RETURN button to exit
a folder or the EXIT button to
return to Home screen.
7. Go to pages 18~20 for instructions
that explain how to control
playback of videos, music, and
pictures on a USB device.
NOTES
If you insert a disc when playing a USB
device, the device mode changes to "Disc"
automatically.
Playing a Disc with User
Recorded Content
You can play multimedia files you have
recorded on Blu-ray, DVD, or CD discs.
1. Place a user recorded disc into
the disc tray with the disc’s label
facing up, and then close the tray.
2.
Use the ◄► buttons to select the
type of content you want to view
or play - VIDEOS, PHOTOS, or
MUSIC - and then press the
v
button.
NOTES
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 2. For
example, if you selected music, you will only
be able to see music files. You can change
this selection by returning to the Home
screen and repeating Step 2.
3. A screen appears listing the
contents of the disc. Depending
on how the contents are arranged,
you will see either folders,
individual files, or both.
4. If necessary, use the
▲▼◄►buttons to select a folder,
and then press the
v
button.
5. Use the ◄►▲▼ buttons to select
a file to view or play, and then
press the
v
button.
6. Press the RETURN button one
or more times to exit a current
screen, exit a folder, or to return to
the Home screen. Press the EXIT
button to return directly to the
Home Screen.
7. Go to pages 18~20 for instructions
that explain how to control
playback of videos, music, and
pictures on a disc.
Using DLNA
DLNA Connection
PC
Blu-ray Disc Player
Play back PC's
files
1. Connect the Blu-ray Disc Player,
your PC, and/or your DLNA
compatible device to the same
network.
2. Follow the directions in the DLNA
software Installation/Instruction
manual to set up devices and files
for playing or viewing.
3. Select Change Device on the
player's Home screen, and then
press the
v
button. In the list
of DLNA connected devices that
appears, select your PC or other
DLNA compatible device, and then
press the
v
button.
4. Use the ◄► buttons to select the
type of content you want to view
or play - VIDEOS, PHOTOS, or
MUSIC - and then press the
v
button.
NOTES
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 4. For
example, if you selected music, you will only
be able to see music files. You can change
this selection by returning to the Home
screen and repeating Step 4.
5. A screen appears listing the
contents of the PC or DLNA
device. Depending on how the
contents are arranged, you will see
either folders, individual files, or
both.
6. If necessary, use the ▲▼◄►
buttons to select a folder, and then
press the
v
button.
7. Use the ◄►▲▼ buttons to select
a file to view or play, and then
press the
v
button.
18
8. Press the RETURN button one
or more times to exit a current
screen, exit a folder, or to return to
the Home screen. Press the EXIT
button to return directly to the
Home Screen.
9. Go to pages 18~20 for instructions
that explain how to control
playback of videos, music, and
pictures on a disc.
Controlling Video Playback
You can control the playback of
video content located on a Blu-ray
disc, DVD, CD, USB device, or your
computer. Depending on the media,
some of the functions described in this
manual may not be available.
During Blu-ray or DVD disc playback,
the Full screen button does not
operate.
Buttons on the Remote Control
used for Video Playback
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
Playback related buttons
The player does not play sound in
Search, Slow or Step mode.
~
To return to normal speed playback, press
the
6
button.
6
button
Starts playback.
5
button
Stops playback.
7
button
Pauses playback.
Fast Motion
Play
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button, the playback speed will
change.
Slow Motion
Play
In pause mode, press the
4
button.
Each time you press the
4
button,
the playback speed will change.
Step Motion
Play
In pause mode, press the
7
button.
Each time you press the
7
button,
a new frame appears.
Skip Motion
Play
During playback, press the
1
or
2
button.
Each time you press the
1
or
2
button, the disc moves to the
previous or next chapter or file.
Using the disc menu, title menu,
popup menu, and title list
DISC MENU
button
During playback, press this button
to start the disc menu function.
TITLE MENU
button
During playback, press this button
to start the title menu function.
POPUP MENU
button
During playback, press this button
to start the popup menu function.
Controlling Music Playback
You can control the playback of music
located on a Blu-ray disc, DVD, CD,
USB device, or your computer.
Buttons on the Remote Control
used for Music Playback
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
4
6
3
2
5
1
NUMBER buttons (Audio CD (CD-DA) only) :
During Playlist playback, press the desired
track number.
The selected track is played.
2
Skip : During playback, press the
1
or
2
button to move to the previous or next file of
the playlist.
3
5
button : Stops a track.
4
Fast Play (Audio CD (CD-DA) only)
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button,
the playback speed will change.
5
Pause : Pauses a track.
6
6
button : Plays the currently selected
track.
Repeat an Audio CD (CD-DA)/
MP3
1. During Playlist playback, press the
TOOLS button.
"
Pause c Select Tools
'
Return
+
00:08 / 05:57
1/6
TRACK 001
05:57
TRACK 002
04:27
TRACK 003
04:07
TRACK 004
03:41
TRACK 005
03:17
TRACK 006
03:35
Playlist
TRACK 001
CD
Tools
Repeat Mode ? Off \
Rip
>
Move
<
Adjust
'
Return
2. Press the ◄► buttons to select
Track, All, Shuffle, or Off.
3. Press the
v
button.
Off
Songs are played in the order in
which they were recorded.
(
) Track
The current song is repeated.
(
) All
All songs are repeated.
(
) Shuffle
Shuffle plays songs in random
order.
19
Playlist
1. To move to the Music List, press
the
5
or RETURN button.
The Music List screen appears.
c Select Tools ( ) Jump to Page ' Return
1/2 Page
Music
TRACK 001
TRACK 001
02:38
TRACK 003
02:38
TRACK 005
02:38
TRACK 007
02:38
TRACK 009
02:38
TRACK 004
02:38
TRACK 002
02:38
TRACK 006
02:38
TRACK 008
02:38
TRACK 010
02:38
CD a Change Device
2.
Press the ▲▼◄► buttons to move
to a desired track, and then press
the YELLOW (C) button. A check
appears on the track.
Repeat this procedure to select
additional tracks.
3. To remove a track from the list,
move to the track, and then press
the YELLOW (C) button again.
The check on the track is
cancelled.
4. When done, press the
v
button.
The tracks you selected are
displayed on the right side of the
screen. The player plays the first
track.
5. To change the play list, press the
5
button or RETURN button to
return to the Music List. Repeat
Steps 2, 3, and 4.
6. To cancel the play list and return
to the Home screen, press the
RETURN or EXIT button.
NOTES
You can create a playlist with up to 99 tracks
on Audio CDs (CD-DA).
If you remove all the tracks from a play list
and then press the
v
button, the player
lists and plays all the tracks on the disc.
Ripping
Lets you copy audio files contents
from an Audio CD (CD-DA) to USB/
HDD device.
1. Open the disc tray. Place the audio
(CD-DA) disc on the tray, and
close the tray. Insert a USB device
into the USB jack on the front of
the product.
2. In Stop mode,
press the ▲▼◄►
buttons to move to a desired track,
and then press the YELLOW (C)
button. A check appears on the
track.
Repeat this procedure to select
additional tracks.
3. To remove a track from the list,
move to the track, and then press
the YELLOW (C) button again.
The check on the track is
cancelled.
4. When done, press the TOOLS
button and then select the Rip
using the ▲▼ buttons. and then
press the
v
button. The Rip
pop-up appears.
5. Use the ▲▼ buttons to select the
device to store the ripped files,
and then press the
v
button.
NOTES
Do not disconnect the device while ripping is
in progress.
6. If you want to cancel ripping, press
the
v
button and then select
Yes. Select No to continue ripping.
7. When ripping is complete, the
"Ripping completed." message
appears. Press the
v
button to
go back to the Playback screen.
NOTES
This function may not be supported by some
discs.
On the Ripping screen, you can also choose
Select All and Deselect All.
-
Use Select All to select all tracks. This
cancels your individual track selections.
-
Use Deselect All to deselect all
selected tracks at once.
Disc Copy to USB
Lets you copy video/photo/music
contents from data Disc to USB/HDD
device.
1. Open the disc tray. Place the data
disc on the tray, and close the tray.
Insert a USB device into the USB
jack on the front of the product.
The new device pop-up appears.
2. Press the ▲ button, and then
press the ◄► buttons to select
Blu-ray, DVD or CD.
3. Use the ▲▼ buttons to select
Photos, Videos or Music, and
then press the
v
button. The
Photos, Videos & Music screen
appears listing the content of the
device. Depending on how the
contents is arranged, you will see
either folders, individual files, or
both.
NOTES
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change
this selection by returning to the Photos,
Videos & Music screen and repeating Step 3.
4. In Stop mode, use the ▲▼◄►
buttons to select the VIDEOS,
PHOTOS, or MUSIC, and then
press the YELLOW (C) button. A
check appears to the left of the
desired item.
5. Repeat Step 4 to select and check
additional desired item.
6. To remove the desired item from
the list, press the YELLOW (C)
again.
The check on the desired item is
removed.
20
7. When done, press the TOOLS
button and then select the Copy
to USB using the ▲▼ buttons.
and then press the
v
button.
The Copy to USB pop-up appears.
8. Use the ▲▼ buttons to select the
device to store the copied files,
and then press the
v
button.
NOTES
Do not disconnect the device while copying is
in progress.
9. If you want to cancel copying,
press the
v
button and then
select Yes. Select No to continue
copying.
10. When copying is complete, the
"Copying completed." message
appears. Press the
v
button to
go back to the Playback screen.
NOTES
This function may not be supported by some
discs.
On the Copying screen, you can also choose
Select All and Deselect All.
-
Use Select All to select all item. This
cancels your individual item selections.
-
Use Deselect all to deselect all selected
item at once.
Playing Photo Contents
You can control the playback of
photo content located on a Blu-ray
disc, DVD, CD, USB device, or your
computer.
Using the Tools Menu
During playback, press the TOOLS
button.
Start Slide
Show/ Stop
Slide Show
Select to start or stop the slide
show.
Slide Show
Speed
Select to set a slide show's
speed.
Background
Music
Select to listen to music while
viewing a slide show.
Zoom
Select to enlarge the current
picture. (Enlarge up to 4 times)
Rotate
Select to rotate the picture. (This
will rotate the picture either
clockwise or counter clockwise.)
Information
Shows the picture information.
NOTES
Depending on the disc or storage device, the
Tools menu may differ.
To enable the background music function, the
photo file must be in the same storage media
as the music file.
However, the sound quality can be affected
by the bit rate of the MP3 file, the size of the
photo, and the encoding method.
You can't enlarge the subtitle and PG graphic
in the full screen mode.
Appendix
Troubleshooting
Before requesting service, please try the following solutions.
PROBLEM SOLUTION
No operation can be
performed with the
remote control.
~
Check the batteries in the remote control. They may need replacing.
~
Operate the remote control at a distance of no more than 6.1m from the player.
~
Remove batteries and hold down one or more buttons for several minutes
to drain the microprocessor inside the remote control to reset it. Reinstall
batteries and try to operate the remote control again.
Disc does not play.
~
Ensure that the disc is installed with the label side facing up.
~
Check the region number of the Blu-ray Disc/DVD.
Disc Menu does not appear.
~
Ensure that the disc has disc menus.
The prohibition message
appears on the screen.
~
This message appears when an invalid button is pressed.
~
The Blu-ray Disc/DVD’s software doesn’t support the feature (e.g., angles).
~
You’ve requested a title or chapter number or search time that is out of
range.
Play mode differs from
the Setup Menu selection.
~
Some of the functions selected in the Setup Menu may not work properly if the disc is not
encoded with the corresponding function.
The screen ratio cannot
be changed.
~
The Screen Ratio is fixed on your Blu-ray Disc/DVD.
~
This is not a problem with the player.
No audio.
~
Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blank.
~
If the HDMI output is set to a resolution your TV cannot support (for
example, 1080p), you may not see a picture on your TV.
~
Press the
^
button (on the front panel) for more than 5 seconds with no
disc inside. All settings will revert to the factory settings.
~
When the factory default settings are restored, all stored user BD data is deleted.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Samsung BD-J5500 Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur

dans d''autres langues