Ericsson AP 6321 Quick Install Manual

Marque: Ericsson

Modèle: AP 6321

Taper: Quick Install Manual

AP 6321 Quick Install Guide

QUICK GUIDE

1/006 92-LZA 101 822 Uen D

reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to

continued progress in methodology, design and manufacturing. Ericsson shall

have no liability for any error or damage of any kind resulting from the use

of this document.

Trademark List

Wi-Fi

is a registered trademark of the Wi-Fi Alliance.

Wi-Fi Certified logo

The Wi-Fi CERTIFIED logo is a registered trademark

of the Wi-Fi Alliance.

Ericsson

Ericsson is the trademark or registered trademark of

Telefonaktiebolaget LM Ericsson. All other product or

service names mentioned in this manual are trademarks

of their respective companies.

1/006 92-LZA 101 822 Uen D | 2013-11-08

Getting Started

1 Getting Started

1.1 Package Contents

Note: Ericsson also offers the following options, which are ordered and

shipped separately:

• AC Power Adapter

• Ceiling Tile Hanger Kit

• Passive PoE Injector

1/006 92-LZA 101 822 Uen D | 2013-11-08

AP 6321 Quick Install Guide

Contact your Ericsson representative for more information.

1.2 Unit Description

1.2.1 Power Connector

The unit does not have a power switch. It is powered on when connected

to a power source. The power adapter, ordered and shipped separately,

automatically adjusts to any voltage between 100~240 volts at 50 Hz or 60 Hz.

The unit draws up to 0.43 A at 48 V DC (20.9 W).

Warning!

The AC Power Adapter relies on the rated fuse or circuit breaker of the wall

outlet (15 A in North America, 10 A in Europe).

Caution!

Use ONLY the Ericsson power adapter for the AP 6321. Use of any other

power adapter can damage the unit and voids the Ericsson product warranty.

1.2.2 Internet Port

Table 1 shows the power consumption for the Internet port.

Table 1 Power Consumption Table

State

Internet Port

Only

Internet Port

and One LAN

Port

Internet Port

and Four LAN

Ports

Idle 5.6 W 6.3 W 8.4 W

Medium Traffic 12 W 12.7 W 14.9 W

High Traffic 16 W 16.7 W 18.9 W

Maximum Traffic 18 W 18.7 W 20.9 W

The PoE switch or power injector must meet local and national regulatory

requirements.

1/006 92-LZA 101 822 Uen D | 2013-11-08

Getting Started

802.3at Power Source Equipment (PSE) Specification:

• 50.0 to 57 V DC, with 30 W output power from the PSE

802.3at Powered Device (PD) Specification:

• 42.5 to 57 V DC at the PD, with 25.5 W maximum input power to the PD

802.3at Cable Specification:

• 100 m maximum length

• Maximum cable pair resistance of 12.5 Ohms, satisfied by using CAT5

or CAT5e as specified by ANSI/TIA/EIA-568 or Class D as specified by

ISO/IEC 11801:1995

• 600 mA maximum current per pair

1.2.3 Reset Button

This button is used to restore the factory default configuration using a paperclip

or pen tip. Hold down the button for 15 seconds or more, until all of the

indicators turn off, to remove any configuration changes and restore the unit

to the factory default configuration.

1/006 92-LZA 101 822 Uen D | 2013-11-08

AP 6321 Quick Install Guide

2 Installing the AP 6321

2.1 Step 1—Select Location

Choose a proper place for the unit. In general, the best location is at the

center of the intended wireless coverage area, within line of sight of all wireless

devices. For optimum performance, consider these guidelines:

• Mount the unit as high as possible above any obstructions in the coverage

area.

• Avoid mounting next to or near building support columns or other

obstructions that can cause reduced signal or null zones in parts of the

coverage area.

• Mount away from any signal absorbing or reflecting structures (such as

those containing metal).

The unit can be mounted on any horizontal surface, on a wall or from a hanging

ceiling.

The unit is UL2043 Certified for Plenum mounting. Installers must use Plenum

rated Ethernet cable for installations in the environmental air space of a

building, such as above suspended ceilings. Installers must follow local and

national codes for above ceiling installations.

Warning!

Do not install the unit in any areas where blasting (blasting caps, radio

controlled equipment) or explosive gases can be present.

Warning!

The unit, its AC power adapter, and its cables are not designed for outdoor

use. They must be located indoors.

5 1/006 92-LZA 101 822 Uen D | 2013-11-08

Installing the AP 6321

2.2 Step 2—Mount on a Flat Surface

Mount the unit only on a flat surface that is at least 1/2-inch (12.7-mm) plywood

or the equivalent. To mount the unit on a ceiling or a wall, use one of the

following options:

• To mount the unit on a wall or on a ceiling that does not have T-rails, use

the pan head Phillips screws provided with the unit.

• To mount the unit on a ceiling that has T-rails, use either a T-rail mounting

bracket or the pan head Phillips screws provided with the unit. T-rail

mounting brackets are included in the Ceiling Tile Hanger Kit (BNCKG0158

or INE 105 3079), which can be ordered separately. The Ceiling Tile

Hanger Kit includes five T-rail mounting brackets and five sets of four

appliance feet.

To mount the unit using the mounting screws provided with the unit, do the

following:

1. Attach the mounting screws to a ceiling or wall.

• Use the included Screw Hole Template as a guide.

• For concrete or brick walls, drill holes and use the included nylon wall

plugs.

• For T-rail installations, drill 3/32-inch (2.4-mm) pilot holes.

• Leave a 5/16-inch (8-mm) gap so the unit can slide over the screw

heads.

2. Attach the appliance feet provided with the unit to the unit.

3. Attach the unit to the mounting screws by doing the following:

a Line up the two mounting slots on the bottom of the unit with the two

mounting screws.

b Slide the unit across into position so that the mounting screws support

the unit.

c Adjust the screw depth as required so that there is a snug fit between

the unit and the mounting screws.

To mount the unit using a T-rail mounting bracket, do the following:

1. Clip the T-rail mounting bracket to a T-rail.

2. Attach the correct appliance feet to the unit:

• For a suspended ceiling with recessed T-rails (this is a ceiling in which

the tiles hang below the T-rails), attach the appliance feet provided

with the unit.

1/006 92-LZA 101 822 Uen D | 2013-11-08

AP 6321 Quick Install Guide

• For a suspended ceiling in which the tiles are flush with the T-rails,

attach the appliance feet provided in the Ceiling Tile Hanger Kit.

3. Attach the unit to the mounting points on the mounting bracket by doing

the following:

a Line up the two mounting slots on the bottom of the unit with the two

mounting points on the mounting bracket.

b Slide the unit across into position so that the mounting points support

the unit.

2.3 Step 3—Connect and Power On

The AP 6321 can get its operating power directly from either of the following

sources:

• An AC wall outlet

• The Internet port when connected to a device that provides IEEE 802.3at

compliant Power over Ethernet (PoE)

If the AP 6321 is connected to both a PoE source device and an AC power

source, AC is disabled.

Figure 1 Wall Outlet Power

1/006 92-LZA 101 822 Uen D | 2013-11-08

Installing the AP 6321

Caution!

Use ONLY the Ericsson power adapter for the AP 6321. Use of any other

power adapter can damage the unit and voids the Ericsson product warranty.

Figure 2 Power over Ethernet

Warning!

If PoE is used, the AP 6321 must be connected to a power source that complies

with IEEE 802.3at, or to an IEC/EN 60950-1 compliant power limited source.

2.4 Step 4—Check Indicators

All indicators are illuminated for about one to two seconds when the unit is

powered on. After powering on, wait 2 minutes and check that the indicators on

the unit match the indicators in Table 2.

Table 2 Indicator Behavior

Indicator Behavior

(FAULT)

Off

81/006 92-LZA 101 822 Uen D | 2013-11-08

AP 6321 Quick Install Guide

Indicator Behavior

(OPERATIONAL)

Green

2.4G Green

5G Green

(INTERNET)

Green

If the indicator behavior does not match Table 2, refer to the AP 6321 Technical

Description, 1/1550-LZA 101 822 for detailed indicator descriptions.

2.5 Step 5—Configure Unit

In most cases, the unit configures itself automatically after powering on. To

configure the unit manually through its local web interface or Command Line

Interface (CLI), refer to the Access Point User Guide, 1/1553-LZA 101 806.

1/006 92-LZA 101 822 Uen D | 2013-11-08

AP 6321 Conformity and Regulatory

Statements

STATEMENT OF COMPLIANCE

1/174 02-LZA 101 822 Uen C

reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to

continued progress in methodology, design and manufacturing. Ericsson shall

have no liability for any error or damage of any kind resulting from the use

of this document.

Trademark List

Wi-Fi

is a registered trademark of the Wi-Fi Alliance.

Wi-Fi Certified Logo

The Wi-Fi CERTIFIED logo is a registered trademark

of the Wi-Fi Alliance.

Ericsson

Ericsson is the trademark or registered trademark of

Telefonaktiebolaget LM Ericsson. All other product or

service names mentioned in this manual are trademarks

of their respective companies.

1/174 02-LZA 101 822 Uen C | 2013-11-25

Contents

1 About this Document 1

1.1 Scope 1

1.2 Target Group 1

1.3 Comments About the Documentation 1

2 Regulatory Information and Disclaimers 2

3 Manufacturer’s US Federal Communication

Commission Conformity Statement 3

3.1 FCC Interference Statement 3

3.2 FCC Radiation Exposure Statement 4

4 Manufacturer’s Industry Canada Conformity Statement 5

5 Manufacturer’s European Community Conformity

Statement 7

6 Declaration of Conformity for RF Exposure 9

7 Product Disposal 10

7.1 Mise au rebut du produit 10

7.2 Produktentsorgung 10

7.3 Verwijdering van het product 10

7.4 Tuotteen hävittäminen 11

7.5 Smaltimento del prodotto 11

7.6 Produktbortskaffelse 11

7.7 Eliminação do produto 11

7.8 Eliminación del producto 11

1/174 02-LZA 101 822 Uen C | 2013-11-25

About this Document

1 About this Document

This section describes the scope and target groups for this document.

1.1 Scope

This document provides the regulatory information, disclaimers, and compliance

statements for the product.

1.2 Target Group

The information in this document is intended for all personnel who want to

learn more about the product.

1.3 Comments About the Documentation

Ericsson encourages you to provide feedback, comments or suggestions so

that we can improve the documentation to better meet your needs. With your

comments provide the following:

• Document title

• Document number and revision

• Page number or section number

Please send your comments to your local Ericsson Support.

1/174 02-LZA 101 822 Uen C | 2013-11-25

AP 6321 Conformity and Regulatory Statements

2 Regulatory Information and Disclaimers

Installation and use of this device must be in strict accordance with the

instructions included in the user documentation provided with the product.

Any changes or modifications to this product not expressly approved by the

party responsible for compliance could void the user’s authority to operate

this equipment.

The manufacturer is not responsible for any interference to radio or television

equipment caused by unauthorized modification of this device, or attachment

of any antennas or equipment other than those specified by the manufacturer.

The manufacturer or its authorized resellers or distributors will assume no

liability for any damage arising from failure to comply with these guidelines, or

failure to comply with local, regional or national safety, electrical or building

codes, or government regulations.

This product is manufactured in China with originating and non-originating

product.

Ce produit est fabriqué en Chine avec des matières originaires et non

originaires du produit.

This device contains the following: FCC ID: RAR40065006; IC:

4674A-40065006 (AP 6321).

1/174 02-LZA 101 822 Uen C | 2013-11-25

Manufacturer’s US Federal Communication Commission Conformity Statement

3 Manufacturer’s US Federal Communication

Commission Conformity Statement

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions (1) this device may not

cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

3.1 FCC Interference Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate

this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

For product available in the USA/Canada market, at 2.4 GHz, only channel 1-11

can be selected. Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operating in

conjunction with any other antenna or transmitter except in accordance with

FCC multi-transmitter product procedures.

1/174 02-LZA 101 822 Uen C | 2013-11-25

AP 6321 Conformity and Regulatory Statements

Operation of this device in the 5.15-5.25 GHz frequency range is restricted

to indoor environments only.

Note: Country code selection is for non-US models only and is not available

to US models. Per FCC regulations, all Wi-Fi products marketed in the

US are fixed to US operating channels only.

3.2 FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 9.8 inches (25 cm) between the radiator and your body.

1/174 02-LZA 101 822 Uen C | 2013-11-25

Manufacturer’s Industry Canada Conformity Statement

4 Manufacturer’s Industry Canada Conformity

Statement

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

For product available in the USA/Canada market, at 2.4 GHz, only channel 1-11

can be selected. Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operating in

conjunction with any other antenna or transmitter except in accordance with IC

multi-transmitter product procedures.

Caution:

The device for the band 5150-5250 MHz is only for indoor usage to reduce

potential for harmful interference to co-channel mobile satellite systems.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and operated

with minimum distance 25 cm between the radiator and your body.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le fonctionnement.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal

1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement

en association avec une autre antenne ou transmetteur.

Avertissement:

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés

uniquement pour une utilisation à l’intérieur afin de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes

canaux.

1/174 02-LZA 101 822 Uen C | 2013-11-25

AP 6321 Conformity and Regulatory Statements

NOTE IMPORTANTE:

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements

IC établies pour un environnement non contrôlé. Cet équipement doit être

installé et utilisé avec un minimum de 25 cm de distance entre la source de

rayonnement et votre corps.

1/174 02-LZA 101 822 Uen C | 2013-11-25

Manufacturer’s European Community Conformity Statement

5 Manufacturer’s European Community

Conformity Statement

Table 1 European Community Conformity Statement

Language Statement

English This equipment is in compliance with the essential

requirements and other relevant provisions of Directive

1999/5/EC.

Deutsch Dieses Gerät entspricht den grundlegenden Anforderungen

und den weiteren entsprecheneden Vorgaben der Richtlinie

1999/5/EU.

Dansk Dette udstyr er i overensstemmelse med de væsentlige krav

og andre relevante bestemmelser i Directiv 1999/5/EF.

Español Este equipo cumple con los requisitos esenciales asi como

con otras disposiciones de la Directiva 1999/5/EC.

Français Cet appareil est conforme aux exigences essentielles et aux

autres dispositions pertinentes de la Directive 1999/5/EC.

Íslenska

Þessi búnaður samrýmist lögboðnum kröfum og öðrum

ákvæðum tilskipunar 1999/5/ESB.

Italiano Questo apparato conforme ai requisiti essenziali ed agli altri

principi sanciti dalla Direttiva 1999/5/EC.

Nederlands Deze apparatuur voldoet aan de belangrijkste eisen en

andere voorzieningen van richtlijn 1999/5/EC.

Norsk Dette utstyret er i samsvar med de grunnleggende krav og

andre relevante bestemmelser i EU-directiv 1999/5/EC.

Português Este equipamento satisfaz os requisitos essenciais e outras

provisões da Directiva 1999/5/EC.

Suomalainen Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset

ja on siinä asetettujen muidenkin ehtojen mukainen.

Svenska Denna utrustning är i överensstämmelse med de väsentliga

kraven och andra relevanta bestämmelser i Direktiv

1999/5/EC.

The Declaration of Conformity related to this product can be found by contacting

Ericsson.

The AP 6321 complies with the following R&TTE Radio standards:

• EN 300 328 v1.8.1 (2012-06) Electromagnetic compatibility and Radio

Spectrum Matters (ERM); Wideband transmission systems; Data

1/174 02-LZA 101 822 Uen C | 2013-11-25

La page charge ...

Ericsson AP 6321 Quick Install Manual

Marque: Ericsson

Modèle: AP 6321

Taper: Quick Install Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Ericsson AP 6321

Documents connexes

Ericsson Wi-Fi AP 5117U Manuel utilisateur

Ericsson AP 6321 Quick Install Manual

Ericsson AP 6321 Quick Install Manual

dans d''autres langues

Documents connexes

Autres documents