Ericsson Wi-Fi AP 5117U Manuel utilisateur

BelAir20EO and AP 511x Series Quick

Install Guide

QUICK GUIDE

1/006 92-LZA 101 803 Uen D

Copyright

reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to

continued progress in methodology, design and manufacturing. Ericsson shall

have no liability for any error or damage of any kind resulting from the use

of this document.

Trademark List

Wi-Fi

®

Wi-Fi

®

is a registered trademark of the Wi-Fi Alliance.

Wi-Fi Certified Logo

The Wi-Fi CERTIFIED logo is a registered trademark

of the Wi-Fi Alliance.

Ericsson

Ericsson is the trademark or registered trademark of

Telefonaktiebolaget LM Ericsson. All other product or

service names mentioned in this manual are trademarks

of their respective companies.

1/006 92-LZA 101 803 Uen D | 2013-12-13

Getting Started

1 Getting Started

1.1 Package Contents

External antennas are ordered and shipped separately.

For AP 5115 to AP 5118:

• Customers supply their own power cable and use the power cable

connector kit to terminate the cable.

• Units can be powered either by AC power or by Power over Ethernet (PoE).

2

1/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide

1.2 AC Power (AP 5115 to AP 5118 Only)

These units accept AC input power in the range of 100–240 V AC. The units do

not have a power switch. They are powered on when connected to a power

source. Maximum AC power consumption is 14.5 W.

Warning!

The unit contains a 5-A fuse and relies on the rated fuse or circuit breaker of

the wall outlet (15 A in North America, 10 A in Europe).

Warning!

Use ONLY the Ericsson power cable connector supplied with the unit. Use of

any other power cable connector can damage the unit and voids the Ericsson

product warranty.

1.3 Internet Port and Power

The unit can be powered with IEEE 802.3af or IEEE 802.3at Power over

Ethernet (PoE). Use IEEE 802.3af PoE for most applications. IEEE 802.3af

PoE supplies a maximum of 12.95 W to the powered device.

Table 1 PoE Power Consumption Table

State PoE Port Only

PoE Port and One LAN

Port

Idle 3.6 W 4.05 W

Medium Traffic 8.4 W 8.85 W

High Traffic 10.8 W 11.25 W

Max. Traffic 11.76 W 12.21 W

The PoE switch or power injector must meet local and national regulatory

requirements.

802.3at Power Source Equipment (PSE) Specification:

• 50.0 to 57 V DC, with 30 W output power from the PSE

3

1/006 92-LZA 101 803 Uen D | 2013-12-13

Getting Started

802.3at Powered Device (PD) Specification:

• 42.5 to 57 V DC at the PD, with 25.5 W maximum input power to the PD

802.3at Cable Specification:

• 100 m maximum length

• Maximum cable pair resistance of 12.5 Ohms, satisfied by using CAT5

or CAT5e as specified by ANSI/TIA/EIA-568 or Class D as specified by

ISO/IEC 11801:1995

• 600 mA maximum current per pair

1.4 Functional Earth Ground and Lightning Protection

Units are not designed to survive a direct lightning hit. However, they are

intended to withstand the voltage and current surges induced from nearby

lightning activity.

The level of required lightning protection depends on regional lightning

conditions and location of installation. For example, an AP installed on a roof

top requires greater lightning protection than an AP installed on the side of a

building. The following is a list of recommended installation practices to mitigate

the voltage and current surges induced from lightning activity. If there is a

conflict between these recommendations and local or national electrical codes,

the local or national electrical codes must be followed.

• For streetlight or hydro/telecom pole mounting the AC power adapter

should be protected with a lightning surge protector. AC power routed to

the power adapter must be routed inside the pole. If power is routed on the

pole exterior, the power must be routed through a metal conduit grounded

at the base of the pole.

• For rooftop installations, the unit must not be mounted at the highest point

on the building. If the building has installed lightning arrestors, the unit must

be located within the umbrella protection zone—a 60 degree zone under

the lighting arrestor, but if possible, the unit should not be located closer

than 30 feet (approx. 10 m) from the lightning arrestor. Power and Ethernet

cables must be routed through independent grounded metal conduits.

• For lightning surge protection, the installer must connect a separate ground

wire between the external chassis of the unit and a ground on the pole. The

ground point on the AP accepts a

1

/4” screw.

• It is recommended for areas susceptible to lightning activity, such as on

poles, rooftops, or on or near any tall structures, that shielded CAT 5e or

CAT 6 Ethernet cable be employed.

• The external antennas ports of the unit require lightning arrestors to be

employed whenever the external antenna is located more than 3 feet

4

1/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide

(approx. 1 m) from the unit. When lightning arrestors are used, they must

be located within 3 feet (approx. 1 m) of the unit and must be grounded

to both the unit and protective earth ground. The

1

/4” GND screw of the

unit can be used for this application.

5

1/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series AP

2 Installing the BelAir20EO and AP 511x

Series AP

2.1 Step 1—Select Location

Choose a proper place for the unit. In general, the best location is at the

center of the intended wireless coverage area, within line of sight of all wireless

devices. For optimum performance, consider these guidelines:

• Mount the unit as high as possible above any obstructions in the coverage

area.

• Avoid mounting next to or near building support columns or other

obstructions that can cause reduced signal or null zones in parts of the

coverage area.

• Mount away from any signal absorbing or reflecting structures (such as

those containing metal).

The unit can be mounted on any wall or on a pole.

Warning!

Do not install the unit in any areas where blasting (blasting caps, radio

controlled equipment) or explosive gases can be present.

Warning!

To comply with FCC radio frequency (RF) exposure limits (FCC OET 65C) for

the general population, antennas must be located a minimum distance of 12

inches (approx. 30 cm) or more from the body of all persons.

61/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide

2.2 Step 2—Mount Unit

Wall or Large Pole Mounting

Large poles have an outer diameter greater than 3 inches (7.6 cms). If mounted

on a flat surface, the unit must be mounted to a surface that is at least 1/2-inch

plywood or its equivalent. Poles must have the equivalent rigidity.

1. Attach the mounting plate to the wall or pole.

• For walls, use up to four 1/4 inch (M6) anchoring bolts. Use the plate as

a drill hole template. The outer edges of the plate must be elevated from

the wall surface while the center channel must touch the wall surface.

• For large poles, use through bolts or use the pairs of slots for stainless

steel strapping. The center channel must touch the pole surface.

2. Connect ground wire to unit.

7 1/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series AP

3. Attach four mounting screws to unit back.

Note: Ground wire not shown.

4. Attach unit to mounting plate:

a Insert mounting screws on the back of the unit into shoulder screw holes

on mounting plate. Slide unit down until screws are into the slots. Tighten

screws snug.

b Screw in the remaining mounting screw at base of unit into the mounting

plate hole.

8

1/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide

Note: Ground wire not shown.

Small Pole Mounting

Small poles have an outer diameter less than 3 inches (7.6 cms).

1. Connect ground wire to unit.

2. Use two stainless steel straps to secure unit to pole.

9

1/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series AP

Note: Ground wire not shown. Strap mounting applies to all units except

the AP 5115 to AP 5118.

2.3 Step 3—Mount and Attach External Antennas

This step applies only to the following APs:

Table 2 APs and Required Antennas

APs

Required

Antennas

Ericsson Description

and Part Number

BelAir20EO-11C,

BelAir20EO-11CR2,

AP 5117R, AP 5117U

Two 5 GHz

External 11.5 dBi

5 GHz 11.5 dBi Dual

Feed Directional Antenna

(BNCKH0091 or INE 105

2162)

BelAir20EO-11D,

BelAir20EO-11DR2,

AP 5118R, AP 5118U

Two 2.4 GHz

External 8 dBi

2.4 GHz 8 dBi Dual

Feed Directional Antenna

(BNCKH0007 or INE 105

2159)

AP 5113 One 2.4 GHz

External 12 dBi

Dual Polarization 2.4–2.5

GHz Flat Panel Antenna

12 dBi (KRE 105 217)

Mounting Kit (KRY 901

293)

The external antennas must be approved by Ericsson specifically for the APs.

The antennas are ordered and shipped separately.

1. Attach the 5 GHz or 2.4 GHz antennas to their mounting surface.

Ericsson provides several different types of 5 GHz and 2.4 GHz antennas,

each with its own requirements and procedures for attaching to a mounting

surface. For details on attaching the antennas to their mounting surface,

10

1/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide

refer to the mounting procedures supplied with the antennas that were

ordered.

2. Connect external 5 GHz or 2.4 GHz antennas to connectors. See the

figure. Connect only antennas that are approved specifically for the units.

Either antenna can connect to either connector. Use thread-locker and

self-amalgamating tape to keep connection tight and waterproof.

• Connect external 5 GHz or 2.4 GHz antennas here.

• Connect only antennas that are approved specifically for the units.

• Either antenna can connect to either connector.

• Use thread-locker and self-amalgamating tape to keep connection tight

and waterproof.

Note: Ground wire and mounting hardware not shown.

2.4 Step 4—Prepare Power Cable (AP 5115 to AP 5118

Only)

Refer to Figure 1.

11

1/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series AP

Figure 1 Power Cable Connector Assembly

1. Place compression nut (4), grommet (3), and body (2) over power cable

as shown in Figure 1.

2. Strip outer jacket and inner conductors as shown in Figure 1.

3. Secure conductors to appropriate terminals by tightening screws on insert

assembly (1). Refer to the following table.

Conductor

Type

North American

Color

European Color

Terminal ID

Ground Green/Yellow Green/Yellow

1

Power Black Brown

2

Neutral White Blue

3

4. Attach body (2) to insert assembly (1) by rotating black knurled ring on

insert assembly in a clockwise direction.

5. Secure compression nut (4) to body (2) by rotating in a clockwise direction.

12

1/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide

2.5 Step 5—Connect and Power On

BelAir20EO and All AP 511x Series: Power over Ethernet

The AP gets its operating power from the PoE port when connected to a device

that provides IEEE 802.3af or 802.3at compliant Power over Ethernet (PoE).

Figure 2 Power Connection for BelAir20EO and All AP 511x Series Power

over Ethernet

Note: Ground wire and mounting hardware not shown.

Warning!

The BelAir20EO and AP 511x series AP must be connected to a power source

that complies to IEEE 802.3af or 802.3at.

Caution!

The PoE connection to the BelAir20EO and AP 511x series AP must use the

supplied Ethernet gland to ensure a waterproof connection. Failure to use the

Ethernet gland voids the Ericsson product warranty.

AP 5115 to AP 5118 Only

The AP can get its operating power directly from an AC power source or from

the Internet port when connected to a device that provides IEEE 802.3af or

802.3at compliant Power over Ethernet (PoE). If the AP is connected to both a

PoE source device and an AC power source, the AP automatically adjusts to

use the most suitable power source.

13

1/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series AP

Figure 3 Power Connections for AP 5115 to AP 5118

Note: Ground wire and mounting hardware not shown.

2.6 Step 6—Check Indicators

After powering on, wait 2 minutes and check the indicators on the unit.

If the indicators are not as shown, refer to the BelAir20EO and AP 511x Series

Technical Description, 1/1550-LZA 101 803.

2.7 Step 7—Configure Unit

In most cases, the unit configures itself automatically after powering on. To

configure the unit manually through its local web interface or Command Line

Interface (CLI), refer to the Access Point User Guide, 1/1553-LZA 101 806.

14

1/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide

document may be reproduced in any form without the written

permission of the copyright owner.

The contents of this document are subject to revision without

notice due to continued progress in methodology, design and

manufacturing. Ericsson shall have no liability for any error or

damage of any kind resulting from the use of this document.

1/006 92-LZA 101 803 Uen D

BelAir20EO and AP 511x Series Conformity

and Regulatory Statements

STATEMENT OF COMPLIANCE

1/174 02-LZA 101 803 Uen C

Copyright

reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to

continued progress in methodology, design and manufacturing. Ericsson shall

have no liability for any error or damage of any kind resulting from the use

of this document.

Trademark List

Wi-Fi

®

Wi-Fi

®

is a registered trademark of the Wi-Fi Alliance.

Wi-Fi Certified Logo

The Wi-Fi CERTIFIED logo is a registered trademark

of the Wi-Fi Alliance.

Ericsson

Ericsson is the trademark or registered trademark of

Telefonaktiebolaget LM Ericsson. All other product or

service names mentioned in this manual are trademarks

of their respective companies.

1/174 02-LZA 101 803 Uen C | 2013-12-13

Contents

1 About this Document 1

1.1 Scope 1

1.2 Target Group 1

1.3 Comments About the Documentation 1

2 Regulatory Information and Disclaimers 2

3 Manufacturer’s US Federal Communication

Commission Conformity Statement 3

3.1 FCC Interference Statement 3

4 Manufacturer’s Industry Canada Conformity Statement 5

5 Manufacturer’s European Community Conformity

Statement 9

6 Declaration of Conformity for RF Exposure 12

7 Product Disposal 13

7.1 Mise au rebut du produit 13

7.2 Produktentsorgung 13

7.3 Verwijdering van het product 13

7.4 Tuotteen hävittäminen 14

7.5 Smaltimento del prodotto 14

7.6 Produktbortskaffelse 14

7.7 Eliminação do produto 14

7.8 Eliminación del producto 14

1/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory Statements

1/174 02-LZA 101 803 Uen C | 2013-12-13

La page charge ...

Ericsson Wi-Fi AP 5117U Manuel utilisateur

Ericsson Wi-Fi AP 5117U Manuel utilisateur

dans d''autres langues

Autres documents