AIRTAME Airtame 2 Guide d'installation
- Catégorie
- Séparateurs vidéo
- Taper
- Guide d'installation
Airtame 2
Content
Whats in the box
Safety precautions
Legal, warranty and regulatory info
How to setup and use
For more information, visit airtame.com/support
What’s in the box?
Airtame2
The Airtame2 is connected with the Aircord USB-C.
Aircord
The Aircord is a y-shaped cable that connects the
Airtame 2 through USB-C to an HDMI port on a TV
/ projector as well as the Airtame 2 power supply
through USB-A.
Power supply
The power supply is required to power the Airtame2.
Use only the power supply provided with the Airtame
2, or other approved Airtame powering accessories.
Important: The Airtame2 should not be powered by
plugging the USB A into the TV / projector. It is not an
adequate power source and is not recommended.
Magnetic wall mount
The magnetic wall mount can be magnetically xed
to the back of the Airtame2, and is used for mounting
the Airtame2.
For exible mounting, attach the magnetic wall
mount to a magnetic area without removing the
protective seal.
For permanent mounting, use the non-removable
adhesive on the back of the magnetic wall mount, and
attach it to a hard, clean surface, such as a wall.
Non-removable adhesive
On the back of the Aircord cable splitter the magnetic
wall mount, are protective seals covering a non-re-
movable adhesive.
Each non-removable adhesive is optional and can be
used to stick to a clean surface, such as a wall, and
other non-magnetic areas.
Important: We advise that you only use the
non- removable adhesive once you have chosen a
permanent location for the Airtame2.
Safety precautions
The Airtame2 has been designed with high attention
to the safety of the user. However, if used improperly,
the Airtame2 can potentially cause re, electrical
shock or personal injury. To avoid any accidents,
please pay attention to these guidelines:
• Use only the power supply and Aircord provided in
the box, or the Airtame PoE Adapter or Extension
Cord accesories (bought seperetarely) commended
by Airtame. Using other cables or power supplies
can inuence or potentially damage the perfor-
mance of the device.
• Do not extend the USB part of the Aircord (the
power cable) e.g. by means of USB extender, USB
hubs or similar. To extend the reach of the power
cable use the Airtame Extension Cord accesory or a
standard power extension cable.
• Note: The Airtame 2 has been approved for use with
power extension cables up to of 3m (9’10”).
Non-removable adhesive
Cable splitter
Power cable
Main cable
Video cable
Aircord
USB-A
HDMI
USB-C
Kensington Lock Slot
USB-C
Micro USB
Reset button
Magnetic wall mount
Airtame 2
Non-removable adhesive
UK power adapter
Power supply and US power adapter
EU power adapter
OC/AU power adapter
Power supply
• Be careful when using the power supply and only
use this in combination with the Airtame2 in dry
locations to avoid the risk of electric shock.
• Do not use the Airtame 2 outdoors.
• Do not place the Airtame 2 in direct sunlight.
• Do not expose the Airtame2 including the Aircord
or power supply to water or extreme conditions
(moisture, heat, cold, dust) as it could potentially
damage or cause it to malfunction.
• Stop the use of the Airtame2 immediately if it (i)
functions in an abnormal manner, (ii) produces
unusual sounds, or (iii) produces unusual odors.
• Do not attempt to disassemble or repair the
Airtame2 yourself. Doing so voids the limited
warranty and could harm you, your TV/projector,
and/or the Airtame2.
• The non-removable adhesives on the magnetic wall
mount and the Aircord may leave marks or detach
from the plastic.
• The Airtame 2 generates heat during use which
results in a temperature increase on the surface
as it leads the heat away, especially when running
at full capacity. Handle with caution as the surface
can feel hot to the touch. If you wish to remove it,
unplug the Airtame 2 from the power source and let
it cool down before touching it.
• Do not mount the Airtame2 on a hot surface or
near a ventilation or hot air exhaust as this can in-
crease its temperature and cause it to malfunction
or shut down.
• The recommended ambient operating temperature
of the Airtame2 is: 5 to 30 °C (41 to 86 °F).
• The recommended Operating Humidity is
20-90%RH non-condensing.
• WARNING: Choking hazard. Some Airtame 2
accessories may present a choking hazard to small
children. Keep these accessories away from small
children.
• WARNING: Strong magnetism. Avoid placing any
media that contains magnets or is sensitive to
magnetism, such as bank cards, audio/video, tapes,
or magnetic memory devices, near the magnetic
wall mount. Media containing information sensitive
to magnets should be kept at least 5 cm (2 inches)
away from the product. Similarly, magnet-sensitive
devices, such as a mechanical watch or measuring
device, can be damaged if they come too close to
the magnetic wall mount.
Legal notices
Model: AT-DG2
FCC ID: 2ADEFAT-DG2
IC: 12460A-ATDG2
Legal entities
Airtame Inc.
109 S 5th St.
Brooklyn, NY 11249
United States
Airtame ApS
Kuglegårdsvej 17
1434 København K
Denmark
License agreement and general terms
The use of any software related to Airtame 2 or any
products by Airtame ApS / Airtame Inc are governed
by the Terms of Service and End User License Agree-
ment which can be found at airtame.com/terms
When using the Airtame 2 or any products of Airtame
ApS / Airtame Inc you acknowledge and accept those
terms.
Warranty information
As warranty is region-dependant please check
warranty information at airtame.com/terms
The latest versions of this manual
Please nd the latest version of this manual on the
company website: airtame.com/setup
Federal Communication Commission
(FCC) Interference Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device compli es with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
FCC Caution
Any changes or modications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate this equipment.
IEEE 802.11g/n operation of this product in the U.S.A.
is rmware-limited to channels 1 through 11.
Wireless Radio Use
This device is restricted to indoor use when operating
in the 5.15 to 5.25 GHz frequency band.
FCC Radiation Exposure Statement
To satisfy FCC and IC exposure requirements, a sepa-
ration distance of at least 20 cm (8 inches) should be
maintained between the antenna of this device and
persons during device operation. Operations at closer
than this distance are not recommended.
The antenna used for this transmitter must not be
co-located in conjunction with any other antenna or
transmitter.
Note to US model owner
To comply with US FCC regulation, the country
selection function has been completely removed from
all US models.
The availability of some specic channels and/or
operational frequency bands are country dependent
and are rmware programmed at the factory to match
the intended destination. The rmware setting is not
accessible by the end user.
Industry Canada (IC) notices
English
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the Equivalent Isotropically Radiated Power
(EIRP) is not more than that necessary for successful
communication.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
French
Conformément à la réglementation d’Industrie
Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou
inférieur) approuvé pour l’émetteur par Industrie
Canada.
Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il
faut choisir le type d’antenne et son gain de sorte que
la Puissance Isotrope Rayonnée Équivalente (PIRE) ne
dépasse pas l’intensité nécessaire à l’établissement
d’une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux con-
ditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le
fonctionnement.
IC Radiation Exposure Statement
Cet appareil est conforme aux limites d’exposition aux
rayonnements de la IC CNR-102 dénies pour un en-
vironnement non contrôlé. An d’éviter la possibilité
de dépasser les limites d’exposition aux fréquences
radio de la IC CNR-102, la proximité humaine à l’an-
tenne ne doit pas être inférieure à 20cm (8 pouces)
pendant le fonctionnement normal.
Wireless Radio Use
Cet appareil est restreint à usage en interieur pour la
bande de fréquence 5.15-5.25 Ghz.
European union
Airtame ApS declares that this equipment is in com-
pliance with the essential requirements and other
provisions of Directive 2014/53/EU.
The full Declaration of Conformity can be found at
airtame.com/compliance
Waste management of Airtame follows the WEEE
Directive 2012/19/EU and the RoHS recast Directive
2011/65/EU. More information can be found at
airtame.com/compliance
Airtame2isdesignedby
Airtame ApS / Airtame Inc
FVIN: cyw89342-dfs_IIIg.clm_blob
www.airtame.com
Installation guide
The optimal installation is only a few steps away
1. Plug in the Aircord
Do not power Airtame 2
through the TV.
Do not extend the Aircord
power cable with USB extension
HDMI
Connect the video cable (HDMI) to the TV.
Powering Airtame 2
Connect the power cable (USB-A) to the power supply. Use the
provided power supply to power the Airtame 2, or the Airtame PoE
Adapter accesory (bought seperately).
USB-A
HDMI
USB-C
Aircord
Power cable
Video cable
USB extension
Approx.
10 cm /
4 inch
2. Mount the Airtame 2
For optimal streaming, mount the Airtame 2 on the wall
approx. 10 cm / 4 inches from the edge of the TV using the
non-removable adhesive.
Permanent mounting
The non-removable adhesive is optional and can be stuck
to a hard surface, such as a wall. Use the non-removable
adhesive for permanent installation.
Optional: Flexible mounting
Fix the magnetic wall mount to the
back of the Airtame 2 and attach it to
a magnetic area without removing the
protective seal.
The backs of many TVs are magnetic.
The magnet will not damage the TV or
projector.
Wi-Fi signal may be weaker when
mounting behind the TV.
Weak WiFi zone
3. Cable management
Hold Airtame 2 onto the magnetic
wall mount while plugging in the
USB-C cable.
Remove the protective seal
and expose the non-removable
adhesive on the cable splitter.
Keep the Aircord straight
and stick the cable splitter
to a surface behind the TV.
Press gently to ensure that
the non-removable adhesive
sticks to the surface.
Remove the protective seal
and expose the non- removable
adhesive on the back of the
magnetic wall mount.
4. Download the Airtame app (and join the cloud)
3. Create an organization at airtame.cloud and add the
Airtame 2 for easy management and more.
2. Install app and follow the instructions.
1. Go to airtame.com/setup and download the Airtame
app that ts the operating system.
To connect to your Airtame, users need to download the
Airtame app.
Airtame - Helpcenter
+
airtame.com/setuphttps://
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
AIRTAME Airtame 2 Guide d'installation
- Catégorie
- Séparateurs vidéo
- Taper
- Guide d'installation
dans d''autres langues
- English: AIRTAME Airtame 2 Installation guide
Documents connexes
Autres documents
-
Samsung n100sp Manuel utilisateur
-
Ubiquiti AmpliFi Protect Manuel utilisateur
-
LG 43LF5100 Le manuel du propriétaire
-
LG 49LF5400 Le manuel du propriétaire
-
Samsung NP400B2YI Manuel utilisateur
-
Samsung NP305V4ZD Manuel utilisateur
-
-
-