ARTHUR MARTIN ELECTROLUX AWT1274AOW Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 5
Programme Chart 6
Consumption values 9
Options 10
Settings 12
Before first use 12
Daily use 12
Hints and tips 16
Care and cleaning 17
Troubleshooting 20
Technical Data 22
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damages that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
unless continuously supervised.
• Children of less than 3 years of age should be kept away
unless continuously supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the
door is open.
• If the appliance has a child safety device, it should be
activated.
2
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
• Do not change the specification of this appliance.
• Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
• The operating water pressure at the water entry point from
the outlet connection must be between 0.5 bar (0.05 MPa)
and 8 bar (0.8 MPa).
• The ventilation opening in the base must not be covered
by a carpet, mat, or any floor covering.
• The appliance must be connected to the water mains using
the new supplied hose sets, or other new hose sets
supplied by the Authorised Service Centre.
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to
clean the appliance.
• Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
SAFETY INSTRUCTIONS
Installation
The installation must comply
with relevant national
regulations.
• Remove all the packaging and the
transit bolts including rubber bush with
plastic spacer.
• Keep the transit bolts in a safe place. If
the appliance is to be moved in the
future they must be reattached to lock
the drum to prevent an internal
damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
3
• Do not install or use the appliance
where the temperature can be less
than 0°C or where it is exposed to the
weather.
• The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
• Make sure that there is air circulation
between the appliance and the floor.
• Do not install the appliance directly
above a floor drain.
• Adjust the feet to have the necessary
space between the appliance and the
flooring.
• Do not install the appliance where the
appliance lid cannot be fully opened.
• Do not put a container to collect
possible water leakage under the
appliance. Contact the Authorised
Service Centre to ensure which
accessories can be used.
Electrical connection
WARNING! Risk of fire and
electric shock.
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by
our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not touch the mains cable or the
mains plug with wet hands.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let
the water flow until it is clean and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
• Do not use an extension hose if the
inlet hose is too short. Contact the
service centre for the replacement of
the inlet hose.
• You can extend the drain hose to
maximum 400 cm. Contact the service
centre for the other drain hose and the
extension.
Use
WARNING! Risk of injury,
electric shock, fire, burns or
damage to the appliance.
• This appliance is for household use
only.
• Follow the safety instructions on the
detergent packaging.
• Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
• Make sure that all metal objects are
removed from the laundry.
• Do not wash fabrics which are heavily
soiled with oil, grease or other greasy
substances. It can damage rubber
parts of the washing machine. Prewash
such fabrics by hand before loading
them into the washing machine.
Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
4
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable close
to the appliance and dispose of it.
• Remove the door catch to prevent
children or pets from becoming trapped
in the drum.
• Dispose of the appliance in accordance
with local requirements for the disposal
of Waste Electrical and Electronic
Equipment (WEEE).
PRODUCT DESCRIPTION
Appliance overview
2
3
1
4
5
6
1
Control panel
2
Lid
3
Lid handle
4
Drain pump filter
5
Feet for levelling the appliance
6
Rating plate
CONTROL PANEL
Control panel description
Essorage
Température
Rinçage
Plus
Départ
Différé
Départ/Pause
Pré-
lavage
Rinçage
Essorage
Vidange
Blanc/Couleurs
Coton Eco
Synthétiques
Chemises
Sport
Rideaux
Jeans
Couette
Soie
Laine/Lavage
à la main
Délicats
90° 60° 40°
30° 20°
1200 800 400
Repassage
Facile
1 2 3 4
910
7
6
8
5
1
Programme knob
5
2
Spin reduction touchpad
(Essorage)
3
Temperature touchpad
(Température)
4
Display
5
Prewash touchpad (Prélavage)
6
Delay start touchpad (Départ
Différé)
7
Extra rinse touchpad (Rinçage
Plus)
8
Easy iron touchpad (Repassage
Facile)
9
Start/Pause touchpad (Départ/
Pause)
10
Time Manager touchpads
Display
A B
E D
C
A. The time area:
• Programme time.
• The alarm codes. Refer to the
chapter “Troubleshooting” for their
description.
• The level of the Time Manager
.
B. The Delay Start indicator.
C. The Child Lock indicator.
D. The Lid Lock indicator:
• It is on, you cannot open the lid.
• It is off, you can open the lid.
• It flashes, you cannot open the lid.
Wait for some minutes until the
indicator is off.
E. Washing phase indicators.
• : the washing phase
• : the rinses phase
• : the spin phase
PROGRAMME CHART
Programme
Temperature
range
Maximum
load
Maximum
spin speed
Programme description
(Type of load and soil level)
Blanc/
Couleurs
90°C - Cold
7 kg
1200 rpm
White cotton and coloured cotton. Normal soil and
light soil.
6
Programme
Temperature
range
Maximum
load
Maximum
spin speed
Programme description
(Type of load and soil level)
Coton
Eco
1)
60°C- 40°C
7 kg
1200 rpm
White cotton and fast-coloured cotton. Normal soil.
The energy consumption decreases and the time of
the washing programme is extended.
Synthé‐
tiques
60°C - Cold
3 kg
1200 rpm
Synthetic items or mixed fabric items. Normal soil.
Délicats
40°C - Cold
2,5 kg
1200 rpm
Delicate fabrics such as acrylics, viscose and
mixed fabrics requiring gentler washing. Normal
soil.
Laine/
Lavage à la
main
40°C - Cold
1 kg
1200 rpm
Machine washable wool, hand washable wool and
other fabrics with «hand washing» care symbol
2)
.
Soie
30°C
1 kg
800 rpm
Special programme for silk and mixed synthetic
items.
Couette
60°C- 30°C
2 kg
800 rpm
Special programme for one synthetic blanket, du‐
vet, bedspread and so on.
Rinçage
Cold
7 kg
1200 rpm
To rinse and spin the laundry. All fabrics, except
woollens and very delicate fabrics. Reduce the spin
speed accordingly to the type of laundry.
Vidange
7 kg To drain the water in the drum. All fabrics.
Essorage
7 kg
1200 rpm
To spin the laundry and to drain the water in the
drum. All fabrics, except woollens and delicate
fabrics.
Jeans
60°C- Cold
3 kg
1200 rpm
Items in denim and jersey. Also for dark coloured
items.
Rideaux
40°C - Cold
3 kg
800 rpm
Special programme for curtains. The prewash phase
is activated automatically.
3)
Sport
30°C
2,5 kg
800 rpm
Synthetic and delicate items. Light soil items or
items to refresh.
7
Programme
Temperature
range
Maximum
load
Maximum
spin speed
Programme description
(Type of load and soil level)
Chemises
30°C
1,5 kg
800 rpm
Synthetic and mixed fabric items. Light soil items
and items to freshen up. For 5 - 6 shirts.
1)
Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,
these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐
gramme». They are the most efficient programmes in terms of combined energy and water consumption for
washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the se‐
lected programme.
2)
During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or
doesn't rotate properly, but this is normal for this programme.
3)
Do not use any detergent for prewash phase to rinse only with water.
Programme options compatibility
Programme
■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■
■ ■ ■
■ ■
■ ■ ■ ■ ■
■
■ ■
■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■
■ ■ ■
■ ■ ■
8
Woolmark Apparel Care - Blue
The wool wash cycle of this machine has been
approved by The Woolmark Company for the
washing of wool garments labelled as «hand
wash» provided that the garments are washed
according to the instructions issued by the
manufacturer of this washing machine. Follow
the garment care label for drying and other
laundry instructions. M1145
The Woolmark symbol is a Certification mark
in many countries.
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant stand‐
ards. Different causes can change the data: the quantity and type of laun‐
dry and ambient temperature. Water pressure, the supply voltage and the
temperature of inlet water may also affect the washing programme dura‐
tion.
Technical specifications may be changed without prior notice to improve
the quality of product.
At the start of the programme, the display shows the programme duration
for the maximum load capacity.
During the washing phase the programme duration is automatically cal‐
culated and can be greatly reduced if the laundry load is lower than the
maximum load capacity (e.g. Cotton 60°C, maximum load capacity 7 kg,
the programme duration exceeds 2 hours; actual load 1 kg, the pro‐
gramme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot
flashes in the display.
Programmes Load
(kg)
Energy
consump‐
tion (kWh)
Water
consump‐
tion (litre)
Approxi‐
mate pro‐
gramme
duration
(minutes)
Remain‐
ing mois‐
ture (%)
1)
Blanc/Couleurs
60°C
7 1,16 58 197 53
Blanc/Couleurs
40°C
7 0,61 56 192 53
Synthétiques
40°C
3 0,45 46 105 35
9
Programmes Load
(kg)
Energy
consump‐
tion (kWh)
Water
consump‐
tion (litre)
Approxi‐
mate pro‐
gramme
duration
(minutes)
Remain‐
ing mois‐
ture (%)
1)
Délicats
40°C
2,5 0,55 46 90 35
Laine/Lavage à la
main
2)
30°C
1 0,35 50 65 30
Standard cotton programmes
Standard 60°C cot‐
ton
7 1,08 46 259 53
Standard 60°C cot‐
ton
3,5 0,70 39 179 53
Standard 40°C cot‐
ton
3,5 0,65 39 179 53
1)
At the end of spin phase.
2)
Not available for some models.
Off Mode (W) Left On Mode (W)
0.48 0.48
The information given in the chart above is compliant with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC
OPTIONS
Température
Set this option to change the default
temperature.
Indicator = cold water.
The indicator of the set temperature
comes on.
Essorage
With this option you can change the
default spin speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
• Set this option to deactivate all spin
phases. Only the drain phase is
available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for
some washing programmes.
Rinse Hold
• Set this option to prevent the laundry
creases.
• The related indicator comes on.
10
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the
laundry creases.
• The lid stays locked. You must drain
the water to unlock the lid.
To drain the water refer to ‘At
the end of the programme’.
Night Cycle
• Set this option to remove all spin
phases and to perform a silent
washing.
• The rinse phase uses more water for
some washing programmes.
• The related indicator comes on.
• The washing programme stops with the
water in the drum. The drum turns
regularly to prevent the laundry
creases.
• The lid stays locked. You must drain
the water to unlock the lid.
To drain the water refer to ‘At
the end of the programme’.
Prélavage
With this option you can add a prewash
phase to a washing programme.
Use this option for heavy soil.
When you set this option the programme
duration increases.
The related indicator comes on.
Départ Différé
With this option you can delay the start of
a programme from 30 minutes to 20
hours.
The display shows the related indicator.
Rinçage Plus
With this option you can add some rinses
to a washing programme.
Use this option for persons allergic to
detergents and in areas where the water
is soft.
The related indicator comes on.
Repassage Facile
The appliance carefully washes and spins
the laundry to prevent the creases.
The appliance decreases the spin speed,
uses more water and adapts the
programme duration to the type of
laundry.
The related indicator comes on.
Time Manager
When you set a washing programme, the
display shows the default duration.
Press or to decrease or increase the
programme duration.
The Time Manager is available only with
the programmes in the table.
indica‐
tor
1
)
1
)
2)
■
■ ■ ■ ■
■ ■ ■ ■ ■ ■
■
■ ■ ■ ■
3)
■
4
)
■
4)
■
4
)
■
4
)
■
4
)
■
4
)
1)
If available.
2)
Shortest: to freshen the laundry.
3)
Longest: Increasing the programme duration gradu‐
ally decreases the energy consumption. The optimized
heating phase saves energy and the longer duration
maintains the same washing results (specially for nor‐
mal soil).
4)
Defaullt duration for all programmes.
11
SETTINGS
Child Lock
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate this option,
press and at the same time
until the indicator comes on/goes
off.
You can activate this option:
• After you press : the options and
the programme knob are locked.
• Before you press : the appliance
cannot start.
Acoustic signals
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic
signals, press and at the same
time for 6 seconds.
If you deactivate the acoustic
signals, they continue operate
when the appliance has a
malfunction.
BEFORE FIRST USE
1. Connect the mains plug to the mains
socket.
2. Open the water tap.
3. Put 2 litre of water in the detergent
compartment for washing phase.
This activates the drain system.
4. Put a small quantity of detergent in the
compartment for washing phase.
5. Set and start a programme for cotton
at the highest temperature without
laundry.
This removes all possible dirt from the
drum and the tub.
DAILY USE
WARNING! Refer to Safety
chapters.
Loading the laundry
1. Open the appliance lid.
2. Push the button A.
The drum opens automatically.
3. Put the laundry in the drum, one item
at a time.
4. Shake the items before you put them
in the appliance.
Make sure not to put too much laundry in
the drum.
5. Close the drum and the lid.
A
CAUTION! Before you close
the lid of your appliance, make
sure that you close the drum
correctly.
12
Detergent compartments. Using
detergent and additives
1. Measure out specified detergents for
washing machine the detergent and the
fabric conditioner.
2. Put the detergent and the fabric
conditioner into the proper compartments.
Always obey the instructions
that you find on the packaging
of the detergent products.
Detergent compartment for prewash
phase.
The marks MAX are the maximum
levels of the quantity of detergent
(powder or liquid).
Detergent compartment for washing
phase.
The marks MAX are the maximum
levels of the quantity of detergent
(powder or liquid).
Compartment for liquid additives
(fabric conditioner, starch).
The mark
M
is the maximum level
for the quantity liquid additives.
Flap for powder or liquid detergent.
Liquid or powder detergent
1.
CLICK
2.
A
13
3.
CLICK
4.
B
• Position A for powder detergent (factory setting).
• Position B for liquid detergent.
When you use the liquid detergent:
• Do not use gelatinous or thick liquid detergents.
• Do not put more liquid then the maximum level.
Setting a programme
1. Turn the programme knob and set the
programme:
• The indicator flashes.
• The display shows the level of the
Time Manager, the programme
duration and the indicators of the
phases of the programme.
2. If necessary, change the temperature
and the spin speed or add available
options. When you activate an option,
the indicator of the set option comes
on.
If you set something incorrect,
the display shows the message
.
Starting a programme without
the delay start
Press .
• The indicator of stops to flash
and stays on.
• The indicator starts to flash on
the display.
• The programme starts, the lid locks,
the display shows the indicator .
• The drain pump can operate for a
short time when the appliance fills
water.
After approximately 15 minutes
from the start of the
programme:
• The appliance adjusts
automatically the
programme duration agree
with the laundry load.
• The display shows the new
value.
Starting a programme with the
delay start
1. Press again and again until the
display shows the delay you want to
set.
The related indicator comes on the
display.
2. Press :
• The appliance starts the
countdown.
• The door locks, the display shows
the indicator .
• When the countdown is completed,
the programme starts automatically.
14
You can cancel or change the
set of the delay start before you
press the . To cancel the
delay start:
• Press to set the
appliance to pause.
• Press until the
display shows '.
• Press again to start
the programme
immediately.
Interrupting a programme and
changing the options
You can change only some options before
they operate.
1. Press .
The indicator flashes.
2. Change the options.
3. Press again.
The programme continues.
Cancelling a running
programme
1. Turn the programme knob to position
to cancel the programme and to
deactivate the appliance.
2. Turn the programme knob again to
activate the appliance. Now, you can
set a new washing programme.
Before starting the new
programme the appliance could
drain the water. In this case,
make sure that the detergent is
still in the detergent
compartment, if not fill the
detergent again.
Opening the lid
While a programme or the delay start
operates, the appliance lid is locked. The
display shows the indicator .
CAUTION! If the temperature
and level of the water in the
drum are too high, you cannot
open the lid.
Open the lid when the delay start
operates:
1. Press the to pause the appliance.
2. Wait until the lid lock indicator
goes off.
3. You can open the lid.
4. Close the lid and press the again.
The delay start continues to operate.
Open the lid when the programme
operates:
1. Turn the programme knob to position
to deactivate the appliance.
2. Wait for some minutes and then open
the appliance lid.
3. Close the lid and set the programme
again.
At the end of the programme
• The appliance stops automatically.
• The acoustic signal operates (if it is
activated).
• In the display comes on.
• The indicator of the goes off.
• The lid lock indicator goes off.
• You can open the lid.
• Remove the laundry from the
appliance. Make sure that the drum is
empty.
• Close the water tap.
• Turn the programme knob to position
to deactivate the appliance.
• Keep the lid ajar, to prevent the mildew
and odours.
The washing programme is completed,
but there is water in the drum:
• The drum turns regularly to prevent the
creases in the laundry.
• The lid lock indicator is on. The
indicator flashes. The lid stays
locked.
15
• You must drain the water to open the
lid.
To drain the water:
1. If necessary, decrease the spin speed.
If you set , the appliance only
drains.
2. Press . The appliance drains the
water and spins.
3. When the programme is completed
and the lid lock indicator goes off,
you can open the lid.
4. Turn the programme knob to position
to deactivate the appliance.
The appliance drains and spins
automatically after
approximately 18 hours (except
for Wool programme).
Stand-by
Some minutes after the end of the
washing programme, if you do not
deactivate the appliance, the energy
saving status activates.
The energy saving status decreases the
energy consumption when the appliance
is on the stand by.
• All indicators and the display go off.
• The indicator of the flashes slowly
• Press one of the options to deactivate
the energy saving status.
If you set a programme or an
option that ends with water in
the drum, the energy saving
status function doesn't
activate to remind you to drain
the water.
HINTS AND TIPS
The laundry load
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are
on the laundry care labels.
• Do not wash white and coloured items
together.
• Some coloured items can discolour
with the first wash. We recommend that
you wash them separately for the first
times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty the pockets and unfold the
items.
• Turn multilayered fabrics, wool and
items with painted illustrations inside
out.
• Remove hard stains with a special
detergent.
• Wash and pre-treat heavy soil stains
before putting items in drum
• Be careful with the curtains. Remove
the hooks and put the curtains in a
washing bag or pillowcase.
• Do not wash laundry without hems or
with cuts. Use a washing bag to wash
small and/or delicate items (e.g.
underwired bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase. If this
occurs, adjust manually the items in the
tub and start the spin phase again.
Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you pre-treat these
stains before you put the items in the
appliance.
Special stain removers are available. Use
the special stain remover that is applicable
to the type of stain and fabric.
16
Detergents and additives
• Only use detergents and additives
specially made for washing machines:
– powder detergents for all types of
fabric,
– powder detergents for delicate
fabrics (40 °C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60
°C max) for all types of fabric, or
special for woollens only.
• Do not mix different types of
detergents.
• To help the environment, do not use
more than the correct quantity of
detergent.
• Obey the instructions that you find on
the on packaging of these products.
• Use the correct products for the type
and colour of the fabric, the programme
temperature and the level of soil.
• If your appliance does not have the
detergent dispenser with the flap
device, add the liquid detergents with a
dosing ball (supplied by the detergent's
manufacturer).
Ecological hints
• Set a programme without the prewash
phase to wash laundry with normal soil.
• Always start a washing programme
with the maximum load of laundry
allowed.
• If necessary, use a stain remover when
you set a programme with a low
temperature.
• To use the correct quantity of
detergent, check the water hardness of
your domestic system. Refer to "Water
hardness".
Water hardness
If the water hardness in your area is high
or moderate, we recommend that you use
a water softener for washing machines. In
areas where the water hardness is soft it
is not necessary to use a water softener.
To know the water hardness in your area,
contact your local water authority.
Use the correct quantity of the water
softener. Obey the instructions that you
find on the packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
External cleaning
Clean the appliance with soap and warm
water only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
Descaling
If the water hardness in your area is high
or moderate, we recommend that you use
a water descaling product for washing
machines.
Regularly examine the drum to prevent
limescale and rust particles.
To remove rust particles use only special
products for washing machines. Do this
separately from the laundry wash.
Always obey the instructions
that you find on the packaging
of the product.
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the
drum. Perform a maintenance wash
regularly. To do this:
• Remove all laundry from the drum.
17
• Select the cotton programme with the
highest temperature with a small
quantity of detergent.
Cleaning the detergent dispenser
1. 2.
3.
Cleaning the drain filter
Do not clean the drain filter if the water in the appliance is hot.
1. 2.
18
3. 4.
5.
Cleaning the inlet hose and the valve filter
1.
1
2
3
2.
19
3. 4.
90˚
Frost precautions
If the appliance is installed in an area
where the temperature can be less than 0
°C, remove the remaining water from the
inlet hose and the drain pump.
Do this procedure also when
you want to do the emergency
drain.
1. Close the water tap and disconnect the
water inlet hose.
2. Disconnect the drain hose from a sink
or spigot.
3. Put the ends of the drain and inlet
hose in a container. Let the water flow
out of the hoses.
4. Set the Drain programme and let it
operate until the end of the cycle.
5. Turn the programme knob to Stop to
disconnect the appliance from the
power supply.
6. Disconnect the appliance.
WARNING! Make sure that the
temperature is more than 0°C
before you use the appliance
again. The manufacturer is not
responsible for damages
caused by low temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
Introduction
The appliance does not start or it stops
during operation.
First try to find a solution to the problem
(refer to the table). If the problem persists,
contact the Authorised Service Centre.
With some problems, the acoustic
signals operate and the display shows
an alarm code:
• - The appliance does not fill with
water properly. Start the appliance
again by pressing Départ/Pause button.
After 10 seconds the door will be
unlocked.
• - The appliance does not drain
the water.
• - The appliance lid or drum doors
are open or not closed correctly.
Please check both!
• - The mains supply is unstable.
Wait until the mains supply is stable.
WARNING! Deactivate the
appliance before you do the
checks.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
ARTHUR MARTIN ELECTROLUX AWT1274AOW Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
dans d''autres langues
Documents connexes
Autres documents
-
Zanussi ZWY61024CI Manuel utilisateur
-
Electrolux EWT1264SS1 Manuel utilisateur
-
-
Zanussi ZWQ61025CI Manuel utilisateur
-
Zanussi ZWQ71235SI Manuel utilisateur
-
Zanussi ZWY51024CI Manuel utilisateur
-
Zanussi ZWY50924CI Manuel utilisateur
-
-
-
Electrolux EWT2066EEW Manuel utilisateur