Arthur_Martin AWY61013WI Manuel utilisateur

Marque: Arthur_Martin

Modèle: AWY61013WI

Catégorie: Machines à laver

Taper: Manuel utilisateur

AWY 61013WI

EN Washing Machine User Manual 2

FR Lave-linge Notice d'utilisation 20

CONTENTS

Safety information 2

Safety instructions 3

Product description 5

Control panel description 5

Indicators 6

Programme Chart 6

Consumption values 8

Options 9

Settings 10

Before first use 10

Daily use 10

Hints and tips 12

Care and cleaning 13

Troubleshooting 15

Technical Data 17

Installation 17

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damages that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Children between 3 and 8 years of age and persons with

very extensive and complex disabilities shall be kept away

unless continuously supervised.

• Children of less than 3 years of age should be kept away

unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• Do not change the specification of this appliance.

• Do not exceed the maximum load of 6 kg (refer to the

"Programme chart" chapter).

• The operating water pressure at the water entry point from

the outlet connection must be between 0.5 bar (0.05 MPa)

and 8 bar (0.8 MPa).

• The ventilation opening in the base must not be covered

by a carpet, mat, or any floor covering.

• The appliance must be connected to the water mains using

the new supplied hose sets, or other new hose sets

supplied by the Authorised Service Centre.

• Old hose sets must not be reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service

Centre or similarly qualified persons to avoid an electrical

hazard.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to

clean the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

SAFETY INSTRUCTIONS

Installation

The installation must comply

with relevant national

regulations.

• Remove all the packaging and the

transit bolts including rubber bush with

plastic spacer.

• Keep the transit bolts in a safe place. If

the appliance is to be moved in the

future they must be reattached to lock

the drum to prevent an internal

damage.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Do not install or use the appliance

where the temperature can be less

than 0°C or where it is exposed to the

weather.

• The floor area on which the appliance

is to be installed must be flat, stable,

heat resistant and clean.

• Make sure that there is air circulation

between the appliance and the floor.

• Do not install the appliance directly

above a floor drain.

• Adjust the feet to have the necessary

space between the appliance and the

flooring.

• Do not install the appliance where the

appliance lid cannot be fully opened.

• Do not put a container to collect

possible water leakage under the

appliance. Contact the Authorised

Service Centre to ensure which

accessories can be used.

Electrical connection

WARNING! Risk of fire and

electric shock.

• The appliance must be earthed.

• Always use a correctly installed

shockproof socket.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not touch the mains cable or the

mains plug with wet hands.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• This appliance complies with the E.E.C.

Directives.

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let

the water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of

the appliance.

• Do not use an extension hose if the

inlet hose is too short. Contact the

service centre for the replacement of

the inlet hose.

• You can extend the drain hose to

maximum 400 cm. Contact the service

centre for the other drain hose and the

extension.

Use

WARNING! Risk of injury,

electric shock, fire, burns or

damage to the appliance.

• This appliance is for household use

only.

• Follow the safety instructions on the

detergent packaging.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

• Make sure that all metal objects are

removed from the laundry.

• Do not wash fabrics which are heavily

soiled with oil, grease or other greasy

substances. It can damage rubber

parts of the washing machine. Prewash

such fabrics by hand before loading

them into the washing machine.

Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains electrical and water supplies.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Remove the door catch to prevent

children or pets from becoming trapped

in the drum.

• Dispose of the appliance in accordance

with local requirements for the disposal

of Waste Electrical and Electronic

Equipment (WEEE).

PRODUCT DESCRIPTION

Appliance overview

Control panel

Lid

Lid handle

Feet for levelling the appliance

Rating plate

CONTROL PANEL DESCRIPTION

Temp. Essorage Départ/PauseRapide

90°

60°

40°

30°

Départ différé

3h 6h 9h

Coton

ECO

Délicats

Laine/

Lavage à la main

Rinçage

Couleurs foncées

Mix 20°

Synthétiques

Coton

Vidange

Essorage

Repassage

facile

Rafraîchir 20'

Jeans

2 3

4567

Programme knob

Départ différé button

Indicators:

Main wash phase

Extra Rinse phase

End of cycle

Départ/Pause button

Rapide button

Essorage selection button

Temp. selection button

INDICATORS

Washing phase

The indicator comes on after pressing

the Start button. This means the appli‐

ance is operating.

Extra rinse

The indicator comes on when the ap‐

pliance performs the extra rinse phase.

End of cycle

The indicator comes on when the pro‐

gramme is completed.

PROGRAMME CHART

Programme

Temperature

range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Coton

90°C - Cold

6 kg

1000 rpm

White cotton and coloured cotton. Normal soil and

light soil.

Coton

Eco

60°C - 40°C

6 kg

1000 rpm

White cotton and fast-coloured cotton. Normal soil.

The energy consumption decreases and the time of

the washing programme is extended.

Synthétiques

60°C - Cold

2,5 kg

1000 rpm

Synthetic items or mixed fabric items. Normal soil.

Délicats

40°C - Cold

2,5 kg

700 rpm

Delicate fabrics such as acrylics, viscose and

mixed fabrics requiring gentler washing. Normal

soil.

Laine/Lavage à

la main

40°C - Cold

1 kg

1000 rpm

Machine washable wool, hand washable wool and

other fabrics with «hand washing» care symbol

Couleurs fon‐

cées

40°C

3 kg

1000 rpm

Cotton items or mixed fabric items in dark col‐

ours. Normal soil.

Mix 20°

20°C

2,5 kg

1000 rpm

Special programme for cotton, synthetic and mixed

fabrics lightly soiled. Select this programme to reduce

the energy consumption. Make sure that the detergent

is suitable for low temperatures in order to have good

washing results

Programme

Temperature

range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Rinçage 6 kg

1000 rpm

To rinse and spin the laundry. All fabrics, except

woollens and very delicate fabrics. Reduce the spin

speed accordingly to the type of laundry.

Vidange 6 kg To drain the water in the drum. All fabrics.

Essorage 6 kg

1000 rpm

To spin the laundry and to drain the water in the drum.

All fabrics, except woollens and delicate fabrics.

Repassage fac‐

ile

60°C - Cold

1 kg

900 rpm

Synthetic items requiring a gentle wash. Normal

and light soil.

Rafraîchir 20'

30°C

1 kg

900 rpm

Synthetic and delicate items. Light soil items or

items to refresh.

Jeans

60°C - Cold

3 kg

1000 rpm

Items in denim and jersey. Normal soil.

30'@ 30°

30°C

2 kg

700 rpm

A short cycle for synthetic and delicate items with

light soil level or for items to freshen up.

Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,

these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐

gramme». They are the most efficient programmes in terms of combined energy and water consumption for

washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the se‐

lected programme.

During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or

doesn't rotate properly, but this is normal for this programme.

The appliance performs the short heating phase if the water temperature is below 20°C. The appliance can

show the temperature setting as “cold”.

The default spin speed is 700 rpm.

To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin phase. The

appliance adds some rinses.

Programme options compatibility

Programme

Rapide

Départ

différé

Coton ■ ■ ■ ■ ■

Coton Eco

■ ■ ■ ■

Synthétiques ■ ■ ■ ■ ■

Programme

Rapide

Départ

différé

Délicats ■ ■ ■ ■ ■

Laine/Lavage à la main ■ ■ ■

Couleurs foncées ■ ■ ■ ■

Mix 20° ■ ■ ■ ■

Rinçage ■ ■ ■ ■

Vidange ■

Essorage ■ ■

Repassage facile ■ ■ ■ ■

Rafraîchir 20' ■ ■

Jeans ■ ■ ■

30'@ 30° ■ ■

When you set the Rapide option, we recommend that you decrease the quantity of the laundry. It is possible to

keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 3 kg, synthetics and

delicates: 1,5 kg.

CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant stand‐

ards. Different causes can change the data: the quantity and type of laun‐

dry and ambient temperature. Water pressure, the supply voltage and the

temperature of inlet water may also affect the washing programme dura‐

tion.

Technical specifications may be changed without prior notice to improve

the quality of product.

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

Coton

60°C

6 1,20 55 150 60

Coton

40°C

6 0,70 55 120 60

Synthétiques

40°C

2,5 0,55 45 103 37

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

Délicats

40°C

2,5 0,50 45 80 37

Laine/Lavage à la

main

30°C

1 0,35 50 68 32

Standard cotton programmes

Standard 60°C cot‐

ton

6 1,09 46 252 60

Standard 60°C cot‐

ton

3 0,80 41 161 60

Standard 40°C cot‐

ton

3 0,67 42 144 60

At the end of spin phase.

Not available for some models.

Off Mode (W) Left On Mode (W)

0.48 0.48

The information given in the chart above is compliant with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC

OPTIONS

Temp.

With this option you can change the

default temperature.

Indicator = cold water.

The indicator of the set temperature

comes on.

Essorage

With this button you can set one of these

options:

The indicator of the set option comes on.

• Automatic spin reduction

Set this option to decrease the

maximum spin speed to a half, but not

less than 400 rpm.

Suitable for very delicate fabrics.

• Rinse Hold

Set this option to prevent the laundry

creases. The drum turns regularly to

prevent the laundry creases.

There is a water in the drum

when the programme is

completed. The lid stays

locked. You must drain the

water to unlock the lid. To

drain the water refer to ‘At

the end of the programme’.

Rapide

With this option you can decrease the

programme duration.

Use this option for items with light soil or

items to refresh.

The related indicator comes on.

Rinçage plus

With this option you can add some rinses

to a washing programme.

Use this option for persons allergic to

detergents and in areas where the water

is soft.

The related indicator comes on.

Départ différé

With this option you can delay the start of

a programme by 9, 6 or 3 hours.

The indicator of the set value is on.

SETTINGS

Permanent Extra Rinse

With this option you can permanently have

an extra rinse when you set a new

programme.

• To activate/deactivate this option

press Essorage and Rapide at the

same time until the indicator comes

on/goes off.

BEFORE FIRST USE

1. Connect the mains plug to the mains

socket.

2. Open the water tap.

3. Put a small quantity of detergent in the

compartment for washing phase.

4. Set and start a programme for cotton

at the highest temperature without

laundry.

This removes all possible dirt from the

drum and the tub.

DAILY USE

WARNING! Refer to Safety

chapters.

Loading the laundry

1. Open the appliance lid.

2. Push the button A.

The drum opens automatically.

3. Put the laundry in the drum, one item

at a time.

4. Shake the items before you put them

in the appliance.

Make sure not to put too much laundry in

the drum.

5. Close the drum and the lid.

CAUTION! Before you close

the lid of your appliance, make

sure that you close the drum

correctly.

See in "Settings" how to activate this option.

Using detergent and additives

Measure out the detergent and the fabric

conditioner.

Detergent compartments

Detergent compartment for

washing phase.

Compartment for liquid addi‐

tives (fabric conditioner, starch).

CAUTION! Do

not exceed the

MAX level.

Setting a programme

1. Turn the programme knob and set the

programme:

• The indicator of the button Départ/

Pause flashes.

2. If necessary, change the spin speed or

add available options. When you

activate an option, the indicator of the

set option comes on.

If you set something incorrect,

the indicator of button Départ/

Pause flashes red.

Starting a programme without

the delay start

Press the button Départ/Pause .

• The indicator of this button stops to

flash and stays on.

• The programme starts, the lid locks,

the indicator of the current cycle

phase is on.

• The drain pump can operate for a

short time at the beginning of the

washing cycle.

Starting a programme with the

delay start

1. Press the button Départ différé to set

the hours of delay you want to set.

The indicator of the set delay is on.

2. Press the button Départ/Pause:

• The appliance starts the

countdown.

• When the countdown is completed,

the programme starts automatically.

You can cancel or change the

set of the delay start before you

press the button Départ/Pause.

To cancel the delay start:

1. Press the button Départ/Pause to set

the appliance to pause.

2. Press Départ différé until the indicator

of the set delay goes off.

Press Départ/Pause again to start the

programme immediately.

Interrupting a programme and

changing the options

You can change only some options before

they operate.

1. Press the button Départ/Pause . The

indicator flashes.

2. Change the options.

3. Press the button Départ/Pause again.

The programme continues.

Cancelling a running

programme

1. Turn the programme knob to position

to cancel the programme and to

deactivate the appliance.

2. Turn the programme knob again to

activate the appliance. Now, you can

set a new washing programme.

Before starting the new

programme the appliance could

drain the water. In this case,

make sure that the detergent is

still in the detergent

compartment, if not fill the

detergent again.

Opening the lid

While a programme operates or the delay

start operates, the appliance lid is locked.

CAUTION! If the temperature

and level of the water in the

drum are too high, you cannot

open the lid.

Open the lid during the first 10 minutes

of the cycle and when the delay start

operates:

1. Press the button Départ/Pause to

pause the appliance.

2. Wait a couple of minutes and then you

can open a lid.

3. Close the lid and press button Départ/

Pause again. The programme

continues (or the delay start).

Open the lid when the programme

operates:

1. Turn the programme knob to position

to deactivate the appliance.

2. Wait for some minutes and then open

the appliance lid.

3. Close the lid and set the programme

again.

At the end of the programme

• The appliance stops automatically.

• The indicator of the button Départ/

Pause goes off.

• The indicator is on.

• You can open the lid.

• Remove the laundry from the

appliance. Make sure that the drum is

empty. Close the water tap.

• Turn the programme knob to position

to deactivate the appliance.

• Keep the lid ajar, to prevent the mildew

and odours.

The washing programme is completed,

but there is water in the drum:

• The drum turns regularly to prevent the

creases in the laundry.

• The indicator of button Départ/Pause

flashes. The lid stays locked.

• You must drain the water to open the

lid.

To drain the water:

1. Set a "Drain" or a "Spin" programme. If

necessary, decrease the spin speed.

2. Press the button Départ/Pause. The

appliance drains the water and spins.

3. When the programme is completed,

after a couple of minutes, you can

open the lid.

4. Turn the programme knob to position

to deactivate the appliance.

HINTS AND TIPS

The laundry load

• Divide the laundry in: white, coloured,

synthetics, delicates and wool.

• Obey the washing instructions that are

on the laundry care labels.

• Do not wash white and coloured items

together.

• Some coloured items can discolour

with the first wash. We recommend that

you wash them separately for the first

times.

• Button up pillowcases, close zippers,

hooks and poppers. Tie up belts.

• Empty the pockets and unfold the

items.

• Turn multilayered fabrics, wool and

items with painted illustrations inside

out.

• Remove hard stains with a special

detergent.

• Wash and pre-treat heavy soil stains

before putting items in drum

• Be careful with the curtains. Remove

the hooks and put the curtains in a

washing bag or pillowcase.

• Do not wash laundry without hems or

with cuts. Use a washing bag to wash

small and/or delicate items (e.g.

underwired bras, belts, tights, etc. ).

• A very small load can cause balance

problems with the spin phase. If this

occurs, adjust manually the items in the

tub and start the spin phase again.

Stubborn stains

For some stains, water and detergent is

not sufficient.

We recommend that you pre-treat these

stains before you put the items in the

appliance.

Special stain removers are available. Use

the special stain remover that is applicable

to the type of stain and fabric.

Detergents and additives

• Only use detergents and additives

specially made for washing machines:

– powder detergents for all types of

fabric,

– powder detergents for delicate

fabrics (40 °C max) and woollens,

– liquid detergents, preferably for low

temperature wash programmes (60

°C max) for all types of fabric, or

special for woollens only.

• Do not mix different types of

detergents.

• To help the environment, do not use

more than the correct quantity of

detergent.

• Obey the instructions that you find on

the on packaging of these products.

• Use the correct products for the type

and colour of the fabric, the programme

temperature and the level of soil.

• If your appliance does not have the

detergent dispenser with the flap

device, add the liquid detergents with a

dosing ball (supplied by the detergent's

manufacturer).

Ecological hints

• Always start a washing programme

with the maximum load of laundry

allowed.

• If necessary, use a stain remover when

you set a programme with a low

temperature.

• To use the correct quantity of

detergent, check the water hardness of

your domestic system. Refer to "Water

hardness".

Water hardness

If the water hardness in your area is high

or moderate, we recommend that you use

a water softener for washing machines. In

areas where the water hardness is soft it

is not necessary to use a water softener.

To know the water hardness in your area,

contact your local water authority.

Use the correct quantity of the water

softener. Obey the instructions that you

find on the packaging of the product.

CARE AND CLEANING

WARNING! Refer to Safety

chapters.

External cleaning

Clean the appliance with soap and warm

water only. Fully dry all the surfaces.

CAUTION! Do not use alcohol,

solvents or chemical products.

Descaling

If the water hardness in your area is high

or moderate, we recommend that you use

a water descaling product for washing

machines.

Regularly examine the drum to prevent

limescale and rust particles.

To remove rust particles use only special

products for washing machines. Do this

separately from the laundry wash.

Always obey the instructions

that you find on the packaging

of the product.

Maintenance wash

With the low temperature programmes it is

possible that some detergent stays in the

drum. Perform a maintenance wash

regularly. To do this:

• Remove all laundry from the drum.

• Select the cotton programme with the

highest temperature with a small

quantity of detergent.

Lid seal

Regularly examine the seal. Clean it when

needed, using ammonia cream cleanser

agent without scratching the seal surface,

Always obey the instructions

that you find on the packaging

of the product.

Cleaning the detergent dispenser

Cleaning the inlet hose and the valve filter

90˚

Frost precautions

If the appliance is installed in an area

where the temperature can be less than

0°C, remove the remaining water from the

inlet hose and the drain pump.

Do this procedure also when

you want to do the emergency

drain.

1. Close the water tap.

2. Remove the water inlet hose.

3. Remove the drain hose from the rear

support and unhook it from sink or

spigot.

4. Put the ends of each drain and inlet

hose in a container. Let the water flow

out of the hoses.

5. Set the Vidange programme and let it

operate until the end of the cycle.

6. Turn the programme knob to position

to deactivate the appliance.

7. Disconnect the appliance from the

mains socket.

WARNING! Make sure that the

temperature is more than 0°C

before you use the appliance

again. The manufacturer is not

responsible for damages

caused by low temperatures.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

Introduction

The start of the appliance does not occur

or it stops during operation.

First try to find a solution to the problem

(refer to the table). If not, contact the

Authorised Service Centre.

The red indicator of button Départ/Pause

flashes.

WARNING! Deactivate the

appliance before you do the

checks.

Possible failures

Problem Possible solution

The programme does

not start.

• Make sure that the mains plug is connected to the mains

socket.

• Make sure that the appliance lid and drum doors are closed

properly.

• Make sure that there is not a damaged fuse in the fuse box.

• Make sure that the Start/Pause has been pressed.

• If the delay start is set, cancel the setting or wait for the end of

countdown.

• Deactivate the Child Lock function if it is on (if available).

The appliance does not

fill with water properly.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low.

For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• This problem may be caused by the filter of the inlet hose or

the valve drain filter which may be clogged. Refer to “Care

and cleaning”. If problem remains please contact the Author‐

ised Service Centre.

• This problem may be caused by the filter of the inlet hose or

the valve drain filter which may be kinks or bends. Refer to

“Care and cleaning”. If problem remains please contact the

Authorised Service Centre.

Problem Possible solution

The appliance does not

drain the water.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or bends.

• This problem may be caused by the clogged drain filter.

Please contact the Authorised Service Centre.

• Make sure that the drain hose is in the correct position. The

hose may be too low.

• Set the drain programme if you set a programme without drain

phase.

• Set the drain programme if you set an option which ends with

water in the tub.

The spin phase does not

operate or the washing

cycle lasts longer than

usually.

• Set the spin programme.

• Make sure that the drain filter is not clogged. Clean the filter, if

necessary. Refer to 'Care and cleaning'.

• This problem may be caused by the clogged drain filter.

Please contact the Authorised Service Centre.

• Adjust manually the items in the tub and start the spin phase

again. This problem may be caused by balance problems.

There is water on the

floor.

• Make sure that the couplings of the water hoses are tight and

there is not water leakages.

• Make sure that the drain hose have no damages.

• Make sure you use the correct detergent and the correct

quantity of it.

You cannot open the ap‐

pliance lid.

• Make sure that the washing programme is finished.

• Set the drain or the spin programme if there is water in the

drum.

The appliance makes an

unusual noise.

• Make sure the levelling of the appliance is correct. Refer to

'Installation'.

• Make sure that the packaging and/or the transit bolts are re‐

moved. Refer to 'Installation'.

• Add more laundry in the drum. The load may be too small.

The washing results are

not satisfactory.

• Increase the detergent quantity or use a different detergent.

• Use special products to remove the stubborn stains before

you wash the laundry.

• Make sure that you set the correct temperature.

• Decrease the laundry load.

You cannot set an op‐

tion.

• Make sure that you press only the wanted button(s).

After the check, activate the appliance.

The programme continues from the point

of interruption.

If the problem occurs again, contact the

Authorised Service Centre.

If the appliance shows other alarm codes

(the indicator of button flashes in red).

Deactivate and activate the appliance. If

the problem continues, contact the

Authorised Service Centre.

Service

We recommend the use of original spare

parts.

When contacting the Authorised Service

Centre, make sure that these data are

available. You can find the information on

the rating plate: model, PNC and Serial

Number. (Mod., Prod. No., Ser. No.)

TECHNICAL DATA

Dimension Width/ Height/ Depth/ To‐

tal depth

400 mm/ 890 mm/ 600 mm/ 600 mm

Electrical connection Voltage

Overall power

Fuse

Frequency

220 - 240 V

2200 W

10 A

50 Hz

Level of protection against ingress of solid particles

and moisture ensured by the protective cover, except

where the low voltage equipment has no protection

against moisture

IPX4

Water supply pressure Minimum

Maximum

0,5 bar (0,05 MPa)

8 bar (0,8 MPa)

Water supply

Cold water

Maximum Load Cotton 6 kg

Energy Efficiency Class A+

Spin Speed Maximum 1000 rpm

Connect the water inlet hose to a water tap with a 3/4'' thread.

INSTALLATION

WARNING! Refer to Safety

chapters.

Unpacking

Positioning

Water supply

3/4”

1/2”

3/4”

Drainage

min.600 mm

max.1000 mm

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put

the packaging in relevant containers to

recycle it. Help protect the environment

and human health by recycling waste of

electrical and electronic appliances. Do

not dispose of appliances marked with the

symbol with the household waste.

Return the product to your local recycling

facility or contact your municipal office.

TABLE DES MATIÈRES

Informations de sécurité 20

Consignes de sécurité 22

Description de l'appareil 23

Description du bandeau de

commande

Voyants 24

Tableau des programmes 25

Valeurs de consommation 27

Options 28

Réglages 29

Avant la première utilisation 29

Utilisation quotidienne 29

Conseils 31

Entretien et nettoyage 33

En cas d'anomalie de fonctionnement 34

Caractéristiques techniques 36

Installation 37

Sous réserve de modifications.

INFORMATIONS DE SÉCURITÉ

Avant d'installer et d'utiliser cet appareil, lisez

soigneusement les instructions fournies. Le fabricant ne

pourra être tenu pour responsable des blessures et dégâts

résultant d'une mauvaise installation ou utilisation.

Conservez toujours les instructions dans un lieu sûr et

accessible pour vous y référer ultérieurement.

Sécurité des enfants et des personnes vulnérables

• Cet appareil peut être utilisé par des enfants de plus de

8 ans, ainsi que des personnes dont les capacités

physiques, sensorielles et mentales sont réduites ou dont

les connaissances et l'expérience sont insuffisantes, à

condition d'être surveillés ou d'avoir reçu des instructions

concernant l'utilisation sécurisée de l'appareil et de

comprendre les risques encourus.

• Les enfants entre 3 et 8 ans et les personnes ayant un

handicap très important et complexe doivent être tenus à

l'écart, à moins d'être surveillés en permanence.

• Les enfants de moins de 3 ans doivent être tenus à l'écart,

à moins d'être surveillés en permanence.

• Ne laissez pas les enfants jouer avec l'appareil.

• Ne laissez pas les emballages à la portée des enfants et

jetez-les convenablement.

• Ne laissez pas les détergents à la portée des enfants.

La page charge ...

Arthur_Martin AWY61013WI Manuel utilisateur

Marque: Arthur_Martin

Modèle: AWY61013WI

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Arthur_Martin AWY61013WI User manual

Arthur_Martin AWY61013WI Manuel utilisateur

Arthur_Martin AWY61013WI Manuel utilisateur

dans d''autres langues

Autres documents