Iee CELLT126DD2 Manuel utilisateur

Iee
Marque
Iee
Modèle
CELLT126DD2
Catégorie
Machines à laver
Taper
Manuel utilisateur
CELLT126DD2
User Manual
EN
Washing
Machine
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 5
Programme Chart 6
Consumption values 9
Options 10
Before first use 11
Daily use 11
Hints and tips 13
Care and cleaning 14
Technical Data 16
Troubleshooting 17
Installation 19
Fiche Product 20
Subject to change without notice.
SAFETY INFORMATION
This machine is only for domestic use and is designed to
wash, rinse and spin machine-washable textiles. You must
observe the following instructions. We refuse to accept any
liability and the guarantee if you do not observe these
recommendations since this could result in damage to
equipment or physical injury.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Do not let children play with the appliance.
• Children aged 3 years and under must be kept away from
this appliance when it is in operation at all times.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the
door is open.
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
2
General Safety
• This appliance is intended to be used in household and
similar applications such as:
– farm houses; staff kitchen areas in shops, offices and
other working environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments.
• Do not change the specification of this appliance.
• Obey the maximum load volume of 6 kg (refer to the
“Programme chart” chapter).
• The operating water pressure (minimum and maximum)
must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).
• The ventilation opening in the base (if applicable) must not
be covered by a carpet, mat, or any floor covering.
• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to
clean the appliance.
• Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
SAFETY INSTRUCTIONS
Installation
• Remove all the packaging and the
transit bolts.
• Keep the transit bolts in a safe place. If
the appliance is to be moved in future
they must be reattached to lock the
drum to prevent internal damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use a damaged
appliance.
• Follow the installation instruction
supplied with the appliance.
• Do not install or use the appliance
where the temperature can be less
3
than 0°C or where it is exposed to the
weather.
• The floor area where the appliance is to
be installed must be flat, stable, heat
resistant and clean.
• Make sure that there is air circulation
between the appliance and the floor.
• Adjust the feet to have the necessary
space between the appliance and the
flooring.
• Do not install the appliance where the
appliance lid cannot be fully opened.
• Do not put a container to collect
possible water leakage under the
appliance. Contact the Authorised
Service Centre to ensure which
accessories can be used.
Electrical connection
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by
our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not touch the mains cable or the
mains plug with wet hands.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let
the water flow until it is clean and clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
Use
WARNING! Risk of injury,
electrical shock, fire, burns or
damage to the appliance.
• Obey the safety instructions on the
detergent packaging.
• Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
• Make sure that you remove all metal
objects from the laundry.
• Do not put a container to collect
possible water leakage under the
appliance. Contact the Authorised
Service Centre to ensure which
accessories can be used.
• Do not use with an external remote-
control system or any other device that
switches on automatically.
Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable close
to the appliance and dispose of it.
• Remove the door catch to prevent
children or pets from becoming trapped
in the drum.
• Dispose of the appliance in accordance
with local requirements for the disposal
of Waste Electrical and Electronic
Equipment (WEEE).
4
PRODUCT DESCRIPTION
Appliance overview
3
1
4
5
2
1
Control panel
2
Lid
3
Lid handle
4
Feet for levelling the appliance
5
Rating plate
CONTROL PANEL
Control panel description
120090°
60°
30°
700
40°
900
1
10 9 8 7 6 5
2 43
1
Programme knob
2
Display
3
Delay Start button
4
Lid locked indicator
5
Start/Pause button
6
Extra Rinse button
7
Super Quick button
8
Rinse Hold button
9
Spin reduction button
5
10
Temperature button
Display
A B
• A
The delay start .
When you press the delay start button,
the display shows the delay start time.
• B
This area shows:
- Programme duration
• - Programme is completed
• - Delay start hours
• - Alarm codes (refer to the
chapter 'Troubleshooting')
• - Message of error. Incorrect
option selection: the display shows this
message for some seconds if:
– You set a option that is not suitable
for the programme.
– You change the programme while it
operates.
PROGRAMME CHART
Programme
Temperature range
Maxi‐
mum
load
Maxi‐
mum
spin
speed
Programme description
(Type of load and soil level)
90°C - Cold
6 kg
1200 rpm
White cotton and coloured cotton. Normal soil
and light soil.
90°C - Cold
6 kg
1200 rpm
White cotton and coloured cotton. Heavy soil
and normal soil.
1)
60°C - 40°C
6 kg
1200 rpm
White cotton and fast-coloured cotton. Normal
soil. The energy consumption decreases and the
time of the washing programme is extended.
60°C - Cold
2,5 kg
1200 rpm
Synthetic items or mixed fabric items. Normal
soil.
40°C - Cold
2,5 kg
700 rpm
Delicate fabrics such as acrylics, viscose, poly‐
ester items. Normal soil.
6
Programme
Temperature range
Maxi‐
mum
load
Maxi‐
mum
spin
speed
Programme description
(Type of load and soil level)
40°C - Cold
1 kg
1200 rpm
Machine washable wool, hand washable wool
and delicate fabrics with «hand washing» care
symbol.
2)
20°C
2,5 kg
1200 rpm
Special programme for cotton, synthetic and mixed
fabrics lightly soiled. Select this programme to re‐
duce the energy consumption. Make sure that the
detergent is suitable for low temperatures in order
to have good washing results
3)
.
2,5 kg
1200
rpm
4)
To rinse and spin the laundry. All fabrics, except
woollens and very delicate fabrics. Reduce the
spin speed accordingly to the type of laundry.
6 kg To drain the water in the drum. All fabrics.
6 kg
1200 rpm
To spin the laundry and to drain the water in the
drum. All fabrics, except woollens and delicate
fabrics.
60°C - Cold
1 kg
900 rpm
Synthetic items requiring a gentle wash. Normal
and light soil.
5)
30°C
1 kg
900 rpm
Synthetic and delicate items. Light soil items or
items to refresh.
60°C - Cold
3 kg
1200 rpm
Items in denim and jersey. Also for dark coloured
items.
7
Programme
Temperature range
Maxi‐
mum
load
Maxi‐
mum
spin
speed
Programme description
(Type of load and soil level)
30°C
1 kg
700 rpm
A short cycle for synthetic and delicate items
with light soil level or for items to freshen up.
1)
Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,
these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐
gramme». They are the most efficient programmes in terms of combined energy and water consumption for
washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the se‐
lected programme.
2)
During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or
doesn't rotate properly, but this is normal for this programme.
3)
The appliance performs the short heating phase if the water temperature is below 20°C. The appliance can
show the temperature setting as “cold”.
4)
The default spin speed is 700 rpm.
5)
To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin phase. The
appliance adds some rinses.
Programme options compatibility
Programme
1)
■ ■ ■ ■ ■
■ ■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■ ■
■ ■ ■ ■
■ ■ ■
■ ■ ■ ■
■ ■ ■ ■
■
8
Programme
1)
■ ■
■ ■ ■ ■
■ ■
■ ■ ■
■
1)
When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep
the full load but the washing results can be unsatisfactory. Recommended load: cotton: 3 kg, synthetics and deli‐
cates: 1,5 kg.
CONSUMPTION VALUES
The data in this table are approximate. Different variables can affect the
data: the quantity and type of laundry, the water and ambient tempera‐
ture.
Programmes Load
(kg)
Energy
consump‐
tion (kWh)
Water
consump‐
tion (litre)
Approxi‐
mate pro‐
gramme
duration
(minutes)
Remain‐
ing mois‐
ture (%)
1)
60 °C
6 1,10 56 180 53
40 °C
6 0,65 54 150 53
40 °C
2,5 0,45 46 105 35
40 °C
2,5 0,55 46 90 35
30 °C
2)
1 0,35 50 65 30
Standard cotton programmes
Standard 60°C cot‐
ton
6 0,80 47 246 53
Standard 60°C cot‐
ton
3 0,54 38 174 53
Standard 40°C cot‐
ton
3 0,49 39 175 53
1)
At the end of spin phase.
2)
Not available for some models.
9
Off Mode [W] Left On Mode [W]
0,48 0,48
The information given in the chart above is compliant with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC
OPTIONS
Température
With this option you can change the
default temperature.
Indicator = cold water
The indicator of the set temperature
comes on.
Essorage
With this option you can set the spin
speed. For the maximum spin speeds see
"Programmes".
The indicator of the set speed comes on.
To drain the water refer to ‘At
the end of the programme’.
Anti-froissage
Select this option to reduce creasing:
• The washing programme ends with
water in the drum. The drum turns
regularly to reduce creasing.
• The door stays locked. You must drain
the water to unlock the door.
To drain the water refer to
"Draining water out after the
end of the cycle".
Rapide
With this option you can decrease the
programme duration.
Use this option for items with light soil or
items to refresh.
The related indicator comes on.
Rinçage Plus
With this option you can add some rinses
to a washing programme.
Use this option for persons allergic to
detergents and in areas where the water
is soft.
The related indicator comes on.
Départ Différé
With this option you can delay the start of
a programme from 30 minutes to 20
hours.
The related indicator comes on and the
display shows the delay time.
Acoustic signals
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic
signals, press
and at the same
time for 6 seconds.
If you deactivate the acoustic
signals, they continue operate
when the appliance has a
malfunction.
10
BEFORE FIRST USE
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton
at the highest temperature without
laundry.
This removes all possible dirt from the
drum and the tub.
DAILY USE
WARNING! Refer to Safety
chapters.
Loading the laundry
1. Open the appliance lid.
2. Push the button A.
The drum opens automatically.
3. Put the laundry in the drum, one item
at a time.
4. Shake the items before you put them
in the appliance.
Make sure not to put too much laundry in
the drum.
5. Close the drum and the lid.
A
CAUTION! Before you close
the lid of your appliance, make
sure that you close the drum
correctly.
Using detergent and additives
1. Measure out the detergent and the
fabric conditioner.
2. Put the detergent and the fabric
conditioner into the compartments.
Detergent compartments
Detergent compartment for
washing phase.
Compartment for liquid addi‐
tives (fabric conditioner, starch).
CAUTION! Do
not exceed the
MAX level.
When you set a prewash option, put the de‐
tergent for prewash phase directly into the
drum.
Setting a programme
1. Turn the programme knob to switch
the appliance on and set the
programme:
• The indicator of the button
flashes.
• The display shows the programme
duration.
2. If necessary, change the spin speed or
add available options. When you
activate an option, the indicator of the
set option comes on.
11
If you set something incorrect,
the display shows the message
.
Starting a programme without
the delay start
Press the button .
• The indicator of the button
stops to flash and stays on.
• The programme starts, the lid locks,
the indicator Verrouillage is on.
• The programme time decreases
with steps of one minute.
The drain pump can operate for
a short time at the beginning of
the washing cycle.
Starting a programme with the
delay start option
1. Press the button again and again
until the display shows the delay you
want to set. The delay start indicator
comes on.
2. Press the button
:
• The door is locked and the indicator
is on.
• The appliance starts the
countdown.
• When the countdown is completed,
the programme starts automatically.
You can cancel or change the
set of the option before you
press the button . After
pressing the button you can
only cancel the option.
To cancel the option:
a. Press the button to set the
appliance to pause. The indicator
of button flashes.
b. Press the button until the
display shows '.
Press the button again to start
the programme immediately.
Changing the options
You can change only some option before
they operate.
1. Press the button . The indicator
flashes.
2. Change the options.
3. Press the button . The programme
continues.
Opening the lid
While a programme operates or the delay
start operates, the appliance lid is locked.
CAUTION! If the temperature
and level of the water in the
drum are too high, you cannot
open the lid.
Open the lid during the first 10 minutes
of the cycle and when the delay start
operates:
1. Press the button to pause the
appliance.
2. Wait a couple of minutes and then you
can open a lid.
3. Close the lid and press button
again. The programme (or the delay
start) continues.
Open the lid when the programme
operates:
1. Turn the programme knob to position
Arrêt to deactivate the appliance.
2. Wait for some minutes and then open
the appliance lid.
3. Close the lid and set the programme
again.
Cancelling a running
programme
1. Turn the programme knob to position
to cancel the programme and to
deactivate the appliance.
12
2. Turn the programme knob again to
activate the appliance. Now, you can
set a new washing programme.
Before starting the new
programme the appliance could
drain the water. In this case,
make sure that the detergent is
still in the detergent
compartment, if not fill the
detergent again.
At the end of the programme
• The appliance stops automatically. The
acoustic signal operates (if it is
activated).
• The indicator of the button goes off
and in the display comes on.
• After a couple of minutes the door lock
indicator goes off.
• You can open the lid.
• Remove the laundry from the
appliance. Make sure that the drum is
empty. Close the water tap.
• Turn the programme knob to position
Arrêt to deactivate the appliance.
Unplug the appliance.
• Keep the lid ajar, to prevent the mildew
and odours.
The washing programme is completed,
but there is water in the drum:
• The drum turns regularly to prevent the
creases in the laundry.
• The indicator of button flashes. The
lid stays locked.
• You must drain the water to open the
lid.
To drain the water:
1. Set a "Drain" or a "Spin" programme. If
necessary, decrease the spin speed.
2. Press the button
. The appliance
drains the water and spins.
3. When the programme is completed,
after a couple of minutes, you can
open the lid.
4. Turn the programme knob to position
Arrêt to deactivate the appliance.
Stand by
Some minutes after the end of the
washing programme, if you do not
deactivate the appliance, the energy
saving status activates. The energy saving
status decreases the energy consumption
when the appliance is on the standby.
Press one of the buttons to deactivate the
energy saving status.
HINTS AND TIPS
The laundry load
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are
on the laundry care labels.
• Do not wash white and coloured items
together.
• Some coloured items can discolour
with the first wash. We recommend that
you wash them separately for the first
times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty the pockets and unfold the
items.
• Turn multilayered fabrics, wool and
items with painted illustrations inside
out.
• Remove hard stains with a special
detergent.
• Wash and pre-treat heavy soil stains
before putting items in drum
• Be careful with the curtains. Remove
the hooks and put the curtains in a
washing bag or pillowcase.
• Do not wash laundry without hems or
with cuts. Use a washing bag to wash
small and/or delicate items (e.g.
underwired bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase. If this
occurs, adjust manually the items in the
tub and start the spin phase again.
13
Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you pre-treat these
stains before you put the items in the
appliance.
Special stain removers are available. Use
the special stain remover that is applicable
to the type of stain and fabric.
Detergents and additives
• Only use detergents and additives
specially made for washing machines:
– powder detergents for all types of
fabric,
– powder detergents for delicate
fabrics (40 °C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60
°C max) for all types of fabric, or
special for woollens only.
• Do not mix different types of
detergents.
• To help the environment, do not use
more than the correct quantity of
detergent.
• Obey the instructions that you find on
the on packaging of these products.
• Use the correct products for the type
and colour of the fabric, the programme
temperature and the level of soil.
• If your appliance does not have the
detergent dispenser with the flap
device, add the liquid detergents with a
dosing ball (supplied by the detergent's
manufacturer).
Ecological hints
• Set a programme without the prewash
phase to wash laundry with normal soil.
• Always start a washing programme
with the maximum load of laundry
allowed.
• If necessary, use a stain remover when
you set a programme with a low
temperature.
• To use the correct quantity of
detergent, check the water hardness of
your domestic system. Refer to "Water
hardness".
Water hardness
If the water hardness in your area is high
or moderate, we recommend that you use
a water softener for washing machines. In
areas where the water hardness is soft it
is not necessary to use a water softener.
To know the water hardness in your area,
contact your local water authority.
Use the correct quantity of the water
softener. Obey the instructions that you
find on the packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
External cleaning
Clean the appliance with soap and warm
water only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
Descaling
If the water hardness in your area is high
or moderate, we recommend that you use
a water descaling product for washing
machines.
Regularly examine the drum to prevent
limescale and rust particles.
To remove rust particles use only special
products for washing machines. Do this
separately from the laundry wash.
Always obey the instructions
that you find on the packaging
of the product.
14
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the
drum. Perform a maintenance wash
regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the
highest temperature with a small
quantity of detergent.
Lid seal
Regularly examine the seal. Clean it when
needed, using ammonia cream cleanser
agent without scratching the seal surface,
Always obey the instructions
that you find on the packaging
of the product.
Cleaning the detergent dispenser
1.
1
2
2.
3.
2
1
4.
15
Cleaning the inlet hose and the valve filter
1.
1
2
3
2.
3. 4.
90˚
Frost precautions
If the appliance is installed in an area
where the temperature can be less than 0°
C, remove the remaining water from the
inlet hose and the drain pump.
1. Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of
the hose.
4. Empty the drain pump. Refer to the
emergency drain procedure.
5. When the drain pump is empty, install
the inlet hose again.
WARNING! Make sure that the
temperature is higher than 0 °C
before you use the appliance
again.
The manufacturer is not
responsible for damages
caused by low temperatures.
TECHNICAL DATA
Dimension Width/ Height/ Depth/ To‐
tal depth
400 mm/ 890 mm/ 600 mm/ 600 mm
Electrical connection Voltage
Overall power
Fuse
Frequency
230 V
2200 W
10 A
50 Hz
16
Level of protection against ingress of solid particles
and moisture ensured by the protective cover, except
where the low voltage equipment has no protection
against moisture
IPX4
Water supply pressure Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Water supply
1)
Cold water
Maximum Load Cotton 6 kg
Energy Efficiency Class A++
Spin Speed Maximum 1200 rpm
1)
Connect the water inlet hose to a water tap with a 3/4'' thread.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
Introduction
The appliance does not start or it stops
during operation.
First try to find a solution to the problem
(refer to the table). If the problem persists,
contact the Authorised Service Centre.
With some problems, the acoustic
signals operate and the display shows
an alarm code:
• - The appliance does not fill with
water properly.
• - The appliance does not drain
the water.
• - The appliance lid or drum doors
are open or not closed correctly.
Please check both!
• - The mains supply is unstable.
Wait until the mains supply is stable.
WARNING! Deactivate the
appliance before you do the
checks.
Possible failures
Problem Possible solution
The programme does
not start.
• Make sure that the mains plug is connected to the mains
socket.
• Make sure that the appliance lid and drum doors are closed
properly.
• Make sure that there is not a damaged fuse in the fuse box.
• Make sure that the Start/Pause has been pressed.
• If the delay start is set, cancel the setting or wait for the end of
countdown.
• Deactivate the Child Lock function if it is on (if available).
17
Problem Possible solution
The appliance does not
fill with water properly.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low.
For this information, contact your local water authority.
• Make sure that the water tap is not clogged.
The appliance does not
drain the water.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the drain hose is in the correct position. The
hose may be too low.
• Set the drain programme if you set a programme without drain
phase.
• Set the drain programme if you set an option which ends with
water in the tub.
The spin phase does not
operate or the washing
cycle lasts longer than
usually.
• Set the spin programme.
• Adjust manually the items in the tub and start the spin phase
again. This problem may be caused by balance problems.
There is water on the
floor.
• Make sure that the couplings of the water hoses are tight and
there is not water leakages.
• Make sure that the drain hose have no damages.
• Make sure you use the correct detergent and the correct
quantity of it.
You cannot open the ap‐
pliance lid.
• Make sure that the washing programme is finished.
• Set the drain or the spin programme if there is water in the
drum.
The appliance makes an
unusual noise.
• Make sure the levelling of the appliance is correct. Refer to
'Installation'.
• Make sure that the packaging and/or the transit bolts are re‐
moved. Refer to 'Installation'.
• Add more laundry in the drum. The load may be too small.
The washing results are
not satisfactory.
• Increase the detergent quantity or use a different detergent.
• Use special products to remove the stubborn stains before
you wash the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
You cannot set an op‐
tion.
• Make sure that you press only the wanted button(s).
After the check, activate the appliance.
The programme continues from the point
of interruption.
If the problem occurs again, contact the
Authorised Service Centre.
If the display shows other alarm codes.
Deactivate and activate the appliance. If
the problem continues, contact the
Service.
18
INSTALLATION
WARNING! Refer to Safety
chapters.
Unpacking
1.
2
1
2.
1
2
1
2
3.
19
Positioning Water supply
3/4”
3/4”
1/2”
3/4”
FI
SE
NO
DK
90
O
90
O
1
1
22
Drainage
min.600 mm
max.1000 mm
FICHE PRODUCT
FICHE PRODUIT
1)
Marque Continental Edison
Référence du modèle CELLT 126DD2
Capacité de lavage nominale (coton) 6 kg
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Iee CELLT126DD2 Manuel utilisateur

Iee
Marque
Iee
Modèle
CELLT126DD2
Catégorie
Machines à laver
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents