Iee ETL2370DIP2A Manuel utilisateur

Marque: Iee

Modèle: ETL2370DIP2A

Catégorie: Machines à laver

Taper: Manuel utilisateur

ETL2370DIP2A

User Manual

Washing

Machine

CONTENTS

Safety information 2

Safety instructions 3

Product description 5

Control panel 5

Programme Chart 6

Consumption values 8

Options 9

Before first use 10

Daily use 10

Hints and tips 13

Care and cleaning 14

Technical Data 16

Troubleshooting 16

Installation 18

Fiche Product 20

Subject to change without notice.

SAFETY INFORMATION

This machine is only for domestic use and is designed to

wash, rinse and spin machine-washable textiles. You must

observe the following instructions. We refuse to accept any

liability and the guarantee if you do not observe these

recommendations since this could result in damage to

equipment or physical injury.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Do not let children play with the appliance.

• Children aged 3 years and under must be kept away from

this appliance when it is in operation at all times.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• This appliance is intended to be used in household and

similar applications such as:

– farm houses; staff kitchen areas in shops, offices and

other working environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

• Do not change the specification of this appliance.

• Obey the maximum load volume of 7 kg (refer to the

“Programme chart” chapter).

• The operating water pressure (minimum and maximum)

must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).

• The ventilation opening in the base (if applicable) must not

be covered by a carpet, mat, or any floor covering.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service

Centre or similarly qualified persons to avoid an electrical

hazard.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to

clean the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging and the

transit bolts.

• Keep the transit bolts in a safe place. If

the appliance is to be moved in future

they must be reattached to lock the

drum to prevent internal damage.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not install or use a damaged

appliance.

• Follow the installation instruction

supplied with the appliance.

• Do not install or use the appliance

where the temperature can be less

than 0°C or where it is exposed to the

weather.

• The floor area where the appliance is to

be installed must be flat, stable, heat

resistant and clean.

• Make sure that there is air circulation

between the appliance and the floor.

• Do not install the appliance directly

over the floor drain.

• Adjust the feet to have the necessary

space between the appliance and the

flooring.

• Do not install the appliance where the

appliance lid cannot be fully opened.

• Do not put a container to collect

possible water leakage under the

appliance. Contact the Authorised

Service Centre to ensure which

accessories can be used.

Electrical connection

• The appliance must be earthed.

• Always use a correctly installed

shockproof socket.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not touch the mains cable or the

mains plug with wet hands.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• This appliance complies with the E.E.C.

Directives.

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let

the water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of

the appliance.

Use

WARNING! Risk of injury,

electrical shock, fire, burns or

damage to the appliance.

• Obey the safety instructions on the

detergent packaging.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

• Make sure that you remove all metal

objects from the laundry.

• Do not put a container to collect

possible water leakage under the

appliance. Contact the Authorised

Service Centre to ensure which

accessories can be used.

• Do not use with an external remote-

control system or any other device that

switches on automatically.

Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains electrical and water supplies.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Remove the door catch to prevent

children or pets from becoming trapped

in the drum.

• Dispose of the appliance in accordance

with local requirements for the disposal

of Waste Electrical and Electronic

Equipment (WEEE).

PRODUCT DESCRIPTION

Appliance overview

Control panel

Lid

Lid handle

Feet for levelling the appliance

Rating plate

CONTROL PANEL

Control panel description

RINÇAGE

PLUS

TEMPS RESTANT

1300

900

700

ANTI-

FROISSAGE

RAPIDE

DÉPART / PAUSE

DÉPART DIFFÉRÉ

VERROUILLAGE

90°

60°

40°

30°

TEMPÉRATURE ESSORAGE

COTON

LAVAGE

SYNTH

TIQUE

RINÇAGE

LICAT

VIDANGE

LAINE

REPASSAGE

FACILE PLUS

MIX 20

COTON ECO

ARRÊT

JEANS

RAFRAÎCHIR

20 MIN

MINI 30

ESSORAGE

10 9 8 7 6 5

2 43

Programme knob

Display

Départ Différé button

Verrouillage lid indicator

Départ/Pause button

Rinçage Plus button

Rapide button

Anti-froissage button

Essorage reduction button

Température button

Display

A B

• A

The delay start .

When you press the delay start button,

the display shows the delay start time.

• B

This area shows:

- Programme duration

• - Programme is completed

• - Delay start hours

• - Alarm codes (refer to the

chapter 'Troubleshooting')

• - Message of error. Incorrect

option selection: the display shows this

message for some seconds if:

– You set a option that is not suitable

for the programme.

– You change the programme while it

operates.

PROGRAMME CHART

Programme

Temperature range

Maxi‐

mum

load

Maxi‐

mum

spin

speed

Programme description

(Type of load and soil level)

Coton

90°C - Cold

7 kg

1300 rpm

White cotton and coloured cotton. Normal soil

and light soil.

Coton+Prélavage

90°C - Cold

7 kg

1300 rpm

White cotton and coloured cotton. Heavy soil

and normal soil.

Coton Eco

60°C - 40°C

7 kg

1300 rpm

White cotton and fast-coloured cotton. Normal

soil. The energy consumption decreases and the

time of the washing programme is extended.

Synthétique

60°C - Cold

3 kg

900 rpm

Synthetic items or mixed fabric items. Normal

soil.

Délicat

40°C - Cold

2,5 kg

700 rpm

Delicate fabrics such as acrylics, viscose and

mixed fabrics requiring a mild washing. Normal

soil.

Laine

40°C - Cold

1 kg

900 rpm

Machine washable wool, hand washable wool

and other fabrics with «hand washing» care sym‐

bol

Programme

Temperature range

Maxi‐

mum

load

Maxi‐

mum

spin

speed

Programme description

(Type of load and soil level)

Mix 20°

20°C

2,5 kg

900 rpm

Special programme for cotton, synthetic and mixed

fabrics lightly soiled. Select this programme to re‐

duce the energy consumption. Make sure that the

detergent is suitable for low temperatures in order

to have good washing results

Rinçage 2,5 kg

1300

rpm

To rinse and spin the laundry. All fabrics, except

woollens and very delicate fabrics. Reduce the

spin speed accordingly to the type of laundry.

Vidange 7 kg To drain the water in the drum. All fabrics.

Essorage 7 kg

1300 rpm

To spin the laundry and to drain the water in the

drum. All fabrics, except woollens and delicate

fabrics.

Repassage Facile Plus

60°C - Cold

1 kg

900 rpm

Synthetic items requiring a gentle wash. Normal

and light soil.

Rafraîchir 20 min

30°C

1 kg

900 rpm

Synthetic and delicate items. Light soil items or

items to refresh.

Jeans

60°C - Cold

3 kg

900 rpm

Items in denim and jersey. Also for dark coloured

items.

Mini 30

30°C

1 kg

700 rpm

A short cycle for synthetic and delicate items

with light soil level or for items to freshen up.

Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,

these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐

gramme». They are the most efficient programmes in terms of combined energy and water consumption for

washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the se‐

lected programme.

During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or

doesn't rotate properly, but this is normal for this programme.

The appliance performs the short heating phase if the water temperature is below 20°C. The appliance can

show the temperature setting as “cold”.

The default spin speed is 700 rpm.

To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin phase. The

appliance adds some rinses.

Programme options compatibility

Programme

Essorage

Anti-froissage

Rapide

Rinçage Plus

Départ Différé

Coton ■ ■ ■ ■ ■

Coton+Prélavage ■ ■ ■ ■ ■

Coton Eco

■ ■ ■ ■

Synthétique ■ ■ ■ ■ ■

Délicat ■ ■ ■ ■

Laine ■ ■ ■

Mix 20° ■ ■ ■ ■

Rinçage ■ ■ ■ ■

Vidange ■

Essorage ■ ■

Repassage Facile Plus ■ ■ ■ ■

Rafraîchir 20 min ■ ■

Jeans ■ ■ ■

Mini 30 ■

When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep

the full load but the washing results can be unsatisfactory. Recommended load: cotton: 3,5 kg, synthetics and

delicates: 1,5 kg.

CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant stand‐

ards. Different causes can change the data: the quantity and type of laun‐

dry and ambient temperature. Water pressure, the supply voltage and the

temperature of inlet water may also affect the washing programme dura‐

tion.

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

Cottons 60°C 7 1,16 58 197 53

Cottons 40°C 7 0,61 56 192 53

Synthetics 40°C 3 0,45 46 105 35

Delicates 40°C 2,5 0,55 46 90 35

Wool/Handwash

30°C

1 0,35 50 65 30

Standard cotton programmes

Standard 60°C cot‐

ton

7 1,08 47 259 53

Standard 60°C cot‐

ton

3,5 0,70 39 179 53

Standard 40°C cot‐

ton

3,5 0,65 39 179 53

At the end of spin phase.

Not available for some models.

Off Mode [W] Left On Mode [W]

0,48 0,48

The information given in the chart above is compliant with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC

OPTIONS

Température

With this option you can change the

default temperature.

Indicator = cold water

The indicator of the set temperature

comes on.

Essorage

With this option you can set the spin

speed. For the maximum spin speeds see

"Programmes".

The indicator of the set speed comes on.

To drain the water refer to ‘At

the end of the programme’.

Anti-froissage

Select this option to reduce creasing:

• The washing programme ends with

water in the drum. The drum turns

regularly to reduce creasing.

• The door stays locked. You must drain

the water to unlock the door.

To drain the water refer to

"Draining water out after the

end of the cycle".

Rapide

With this option you can decrease the

programme duration.

Use this option for items with light soil or

items to refresh.

The related indicator comes on.

Rinçage Plus

With this option you can add some rinses

to a washing programme.

Use this option for persons allergic to

detergents and in areas where the water

is soft.

The related indicator comes on.

Départ Différé

With this option you can delay the start of

a programme from 30 minutes to 20

hours.

The related indicator comes on and the

display shows the delay time.

Acoustic signals

The acoustic signals operate when:

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic

signals, press Anti-froissage and Rapide

at the same time for 6 seconds.

If you deactivate the acoustic

signals, they continue operate

when the appliance has a

malfunction.

BEFORE FIRST USE

1. Put a small quantity of detergent in the

compartment for washing phase.

2. Set and start a programme for cotton

at the highest temperature without

laundry.

This removes all possible dirt from the

drum and the tub.

DAILY USE

WARNING! Refer to Safety

chapters.

Loading the laundry

1. Open the appliance lid.

2. Push the button A.

The drum opens automatically.

3. Put the laundry in the drum, one item

at a time.

4. Shake the items before you put them

in the appliance.

Make sure not to put too much laundry in

the drum.

5. Close the drum and the lid.

CAUTION! Before you close

the lid of your appliance, make

sure that you close the drum

correctly.

Using detergent and additives

Measure out the detergent and the fabric

conditioner.

Detergent compartments

Detergent compartment for

washing phase.

Compartment for liquid addi‐

tives (fabric conditioner, starch).

CAUTION! Do

not exceed the

MAX level.

When you set a prewash option, put the de‐

tergent for prewash phase directly into the

drum.

Setting a programme

1. Turn the programme knob to switch

the appliance on and set the

programme:

• The indicator of the button Départ/

Pause flashes.

• The display shows the programme

duration.

2. If necessary, change the spin speed or

add available options. When you

activate an option, the indicator of the

set option comes on.

If you set something incorrect,

the display shows the message

Starting a programme without

the delay start

Press the button Départ/Pause.

• The indicator of the button Départ/

Pause stops to flash and stays on.

• The programme starts, the lid locks,

the indicator Verrouillage is on.

• The programme time decreases

with steps of one minute.

The drain pump can operate for

a short time at the beginning of

the washing cycle.

Starting a programme with the

delay start option

1. Press the button Départ Différé again

and again until the display shows the

delay you want to set.

2. Press the button Départ/Pause:

• The lid is locked and the indicator

Verrouillage is on.

• The appliance starts the

countdown.

• When the countdown is completed,

the programme starts automatically.

You can cancel or change the

set of the Départ Différé option

before you press the button

Départ/Pause. After pressing

the button Départ/Pause you

can only cancel the Départ

Différé option.

To cancel the Départ Différé option:

a. Press the button Départ/Pause to

set the appliance to pause. The

indicator of button Départ/Pause

flashes.

b. Press the button Départ Différé

until the display shows '.

Press the button Départ/Pause

again to start the programme

immediately.

Changing the options

You can change only some option before

they operate.

1. Press the button Départ/Pause. The

indicator flashes.

2. Change the options.

3. Press the button Départ/Pause. The

programme continues.

Opening the lid

While a programme operates or the delay

start operates, the appliance lid is locked.

CAUTION! If the temperature

and level of the water in the

drum are too high, you cannot

open the lid.

Open the lid during the first 10 minutes

of the cycle and when the delay start

operates:

1. Press the button Départ/Pause to

pause the appliance.

2. Wait a couple of minutes and then you

can open a lid.

3. Close the lid and press button Départ/

Pause again. The programme (or the

delay start) continues.

Open the lid when the programme

operates:

1. Turn the programme knob to position

Arrêt to deactivate the appliance.

2. Wait for some minutes and then open

the appliance lid.

3. Close the lid and set the programme

again.

Cancelling a running

programme

1. Turn the programme knob to position

Arrêt to cancel the programme and to

deactivate the appliance.

2. Turn the programme knob again to

activate the appliance. Now, you can

set a new washing programme.

Before starting the new

programme the appliance could

drain the water. In this case,

make sure that the detergent is

still in the detergent

compartment, if not fill the

detergent again.

At the end of the programme

• The appliance stops automatically. The

acoustic signal operates (if it is

activated).

• The indicator of the button Départ/

Pause goes off and in the display

comes on.

• After a couple of minutes the door lock

indicator Verrouillage goes off.

• You can open the lid.

• Remove the laundry from the

appliance. Make sure that the drum is

empty. Close the water tap.

• Turn the programme knob to position

Arrêt to deactivate the appliance.

Unplug the appliance.

• Keep the lid ajar, to prevent the mildew

and odours.

The washing programme is completed,

but there is water in the drum:

• The drum turns regularly to prevent the

creases in the laundry.

• The indicator of button Départ/Pause

flashes. The lid stays locked.

• You must drain the water to open the

lid.

To drain the water:

1. Set a "Drain" or a "Spin" programme. If

necessary, decrease the spin speed.

2. Press the button Départ/Pause. The

appliance drains the water and spins.

3. When the programme is completed,

after a couple of minutes, you can

open the lid.

4. Turn the programme knob to position

Arrêt to deactivate the appliance.

Stand by

Some minutes after the end of the

washing programme, if you do not

deactivate the appliance, the energy

saving status activates. The energy saving

status decreases the energy consumption

when the appliance is on the standby:

• The brightness of the display reduces.

• The indicator of button Start flashes

slowly.

Press one of the buttons to deactivate the

energy saving status.

HINTS AND TIPS

The laundry load

• Divide the laundry in: white, coloured,

synthetics, delicates and wool.

• Obey the washing instructions that are

on the laundry care labels.

• Do not wash white and coloured items

together.

• Some coloured items can discolour

with the first wash. We recommend that

you wash them separately for the first

times.

• Button up pillowcases, close zippers,

hooks and poppers. Tie up belts.

• Empty the pockets and unfold the

items.

• Turn multilayered fabrics, wool and

items with painted illustrations inside

out.

• Remove hard stains with a special

detergent.

• Wash and pre-treat heavy soil stains

before putting items in drum

• Be careful with the curtains. Remove

the hooks and put the curtains in a

washing bag or pillowcase.

• Do not wash laundry without hems or

with cuts. Use a washing bag to wash

small and/or delicate items (e.g.

underwired bras, belts, tights, etc. ).

• A very small load can cause balance

problems with the spin phase. If this

occurs, adjust manually the items in the

tub and start the spin phase again.

Stubborn stains

For some stains, water and detergent is

not sufficient.

We recommend that you pre-treat these

stains before you put the items in the

appliance.

Special stain removers are available. Use

the special stain remover that is applicable

to the type of stain and fabric.

Detergents and additives

• Only use detergents and additives

specially made for washing machines:

– powder detergents for all types of

fabric,

– powder detergents for delicate

fabrics (40 °C max) and woollens,

– liquid detergents, preferably for low

temperature wash programmes (60

°C max) for all types of fabric, or

special for woollens only.

• Do not mix different types of

detergents.

• To help the environment, do not use

more than the correct quantity of

detergent.

• Obey the instructions that you find on

the on packaging of these products.

• Use the correct products for the type

and colour of the fabric, the programme

temperature and the level of soil.

• If your appliance does not have the

detergent dispenser with the flap

device, add the liquid detergents with a

dosing ball (supplied by the detergent's

manufacturer).

Ecological hints

• Set a programme without the prewash

phase to wash laundry with normal soil.

• Always start a washing programme

with the maximum load of laundry

allowed.

• If necessary, use a stain remover when

you set a programme with a low

temperature.

• To use the correct quantity of

detergent, check the water hardness of

your domestic system. Refer to "Water

hardness".

Water hardness

If the water hardness in your area is high

or moderate, we recommend that you use

a water softener for washing machines. In

areas where the water hardness is soft it

is not necessary to use a water softener.

To know the water hardness in your area,

contact your local water authority.

Use the correct quantity of the water

softener. Obey the instructions that you

find on the packaging of the product.

CARE AND CLEANING

WARNING! Refer to Safety

chapters.

External cleaning

Clean the appliance with soap and warm

water only. Fully dry all the surfaces.

CAUTION! Do not use alcohol,

solvents or chemical products.

Descaling

If the water hardness in your area is high

or moderate, we recommend that you use

a water descaling product for washing

machines.

Regularly examine the drum to prevent

limescale and rust particles.

To remove rust particles use only special

products for washing machines. Do this

separately from the laundry wash.

Always obey the instructions

that you find on the packaging

of the product.

Maintenance wash

With the low temperature programmes it is

possible that some detergent stays in the

drum. Perform a maintenance wash

regularly. To do this:

• Remove all laundry from the drum.

• Select the cotton programme with the

highest temperature with a small

quantity of detergent.

Lid seal

Regularly examine the seal. Clean it when

needed, using ammonia cream cleanser

agent without scratching the seal surface,

Always obey the instructions

that you find on the packaging

of the product.

Cleaning the detergent

dispenser

Cleaning the inlet hose and the

valve filter

90˚

Frost precautions

If the appliance is installed in an area

where the temperature can be less than 0°

C, remove the remaining water from the

inlet hose and the drain pump.

1. Disconnect the mains plug from the

mains socket.

2. Close the water tap.

3. Put the two ends of the inlet hose in a

container and let the water flow out of

the hose.

4. Empty the drain pump. Refer to the

emergency drain procedure.

5. When the drain pump is empty, install

the inlet hose again.

WARNING! Make sure that the

temperature is higher than 0 °C

before you use the appliance

again.

The manufacturer is not

responsible for damages

caused by low temperatures.

TECHNICAL DATA

Dimension Width/ Height/ Depth/ To‐

tal depth

400 mm/ 890 mm/ 600 mm/ 600 mm

Electrical connection Voltage

Overall power

Fuse

Frequency

230 V

2200 W

10 A

50 Hz

Level of protection against ingress of solid particles

and moisture ensured by the protective cover, except

where the low voltage equipment has no protection

against moisture

IPX4

Water supply pressure Minimum

Maximum

0,5 bar (0,05 MPa)

8 bar (0,8 MPa)

Water supply

Cold water

Maximum Load Cotton 7 kg

Energy Efficiency Class A++

Spin Speed Maximum 1300 rpm

Connect the water inlet hose to a water tap with a 3/4'' thread.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

Introduction

The appliance does not start or it stops

during operation.

First try to find a solution to the problem

(refer to the table). If the problem persists,

contact the Authorised Service Centre.

With some problems, the acoustic

signals operate and the display shows

an alarm code:

• - The appliance does not fill with

water properly.

• - The appliance does not drain

the water.

• - The appliance lid or drum doors

are open or not closed correctly.

Please check both!

• - The mains supply is unstable.

Wait until the mains supply is stable.

WARNING! Deactivate the

appliance before you do the

checks.

Possible failures

Problem Possible solution

The programme does

not start.

• Make sure that the mains plug is connected to the mains

socket.

• Make sure that the appliance lid and drum doors are closed

properly.

• Make sure that there is not a damaged fuse in the fuse box.

• Make sure that the Start/Pause has been pressed.

• If the delay start is set, cancel the setting or wait for the end of

countdown.

• Deactivate the Child Lock function if it is on (if available).

The appliance does not

fill with water properly.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low.

For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• This problem may be caused by the filter of the inlet hose or

the valve drain filter which may be clogged. Refer to “Care

and cleaning”. If problem remains please contact the Author‐

ised Service Centre.

• This problem may be caused by the filter of the inlet hose or

the valve drain filter which may be kinks or bends. Refer to

“Care and cleaning”. If problem remains please contact the

Authorised Service Centre.

The appliance does not

drain the water.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or bends.

• This problem may be caused by the clogged drain filter.

Please contact the Authorised Service Centre.

• Make sure that the drain hose is in the correct position. The

hose may be too low.

• Set the drain programme if you set a programme without drain

phase.

• Set the drain programme if you set an option which ends with

water in the tub.

The spin phase does not

operate or the washing

cycle lasts longer than

usually.

• Set the spin programme.

• Make sure that the drain filter is not clogged. Clean the filter, if

necessary. Refer to 'Care and cleaning'.

• This problem may be caused by the clogged drain filter.

Please contact the Authorised Service Centre.

• Adjust manually the items in the tub and start the spin phase

again. This problem may be caused by balance problems.

There is water on the

floor.

• Make sure that the couplings of the water hoses are tight and

there is not water leakages.

• Make sure that the drain hose have no damages.

• Make sure you use the correct detergent and the correct

quantity of it.

Problem Possible solution

You cannot open the ap‐

pliance lid.

• Make sure that the washing programme is finished.

• Set the drain or the spin programme if there is water in the

drum.

The appliance makes an

unusual noise.

• Make sure the levelling of the appliance is correct. Refer to

'Installation'.

• Make sure that the packaging and/or the transit bolts are re‐

moved. Refer to 'Installation'.

• Add more laundry in the drum. The load may be too small.

The washing results are

not satisfactory.

• Increase the detergent quantity or use a different detergent.

• Use special products to remove the stubborn stains before

you wash the laundry.

• Make sure that you set the correct temperature.

• Decrease the laundry load.

You cannot set an op‐

tion.

• Make sure that you press only the wanted button(s).

After the check, activate the appliance.

The programme continues from the point

of interruption.

If the problem occurs again, contact the

Authorised Service Centre.

If the display shows other alarm codes.

Deactivate and activate the appliance. If

the problem continues, contact the

Service.

INSTALLATION

WARNING! Refer to Safety

chapters.

Unpacking

Positioning Water supply

3/4”

1/2”

3/4”

Drainage

min.600 mm

max.1000 mm

FICHE PRODUCT

FICHE PRODUIT

Marque Curtiss

Référence du modèle ETL2370DIP2A

Capacité de lavage nominale (coton) 7 kg

La page charge ...

Iee ETL2370DIP2A Manuel utilisateur

Marque: Iee

Modèle: ETL2370DIP2A

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Iee ETL2370DIP2A User manual

Iee ETL2370DIP2A Manuel utilisateur

Iee ETL2370DIP2A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents