Iee ETL1055D Manuel utilisateur

Iee
Marque
Iee
Modèle
ETL1055D
Catégorie
Machines à laver
Taper
Manuel utilisateur
ETL 1055D
User Manual
EN
Washing
Machine
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 5
Programme Chart 6
Consumption values 8
Options 9
Before first use 9
Daily use 10
Hints and tips 12
Care and cleaning 13
Technical Data 15
Troubleshooting 16
Installation 17
Fiche Produit 19
Subject to change without notice.
SAFETY INFORMATION
This machine is only for domestic use and is designed to
wash, rinse and spin machine-washable textiles. You must
observe the following instructions. We refuse to accept any
liability and the guarantee if you do not observe these
recommendations since this could result in damage to
equipment or physical injury.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision.
•
Keep all packaging away from children.
•
Keep all detergents away from children.
•
Keep children and pets away from the appliance door when
it is open.
General Safety
•
This appliance is intended to be used in household and
similar applications such as:
2
– farm houses; staff kitchen areas in shops, offices and
other working environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments.
• Do not change the specification of this appliance.
• Obey the maximum load volume of 5,5 kg (refer to the
“Programme chart” chapter).
• The operating water pressure (minimum and maximum)
must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).
• The ventilation openings in the base (if applicable) must not
be obstructed by a carpet.
• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• Before maintenance, deactivate the appliance and
disconnect the mains plug from the mains socket.
•
Do not use water spray and steam to clean the appliance.
•
Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move
the appliance again you must block the
drum.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Do not install or use a damaged
appliance.
• Obey the installation instruction supplied
with the appliance.
• Do not install or use the appliance where
the temperature is less than 0 °C or
where it is exposed to the weather.
• Make sure that the floor where you
install the appliance is flat, stable, heat
resistant and clean.
• Make sure that there is air circulation
between the appliance and the floor.
• Adjust the feet to have the necessary
space between the appliance and the
carpet.
• Do not install the appliance where the
appliance lid can not be fully opened.
Electrical connection
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
3
• Make sure that the electrical information
on the rating plate agrees with the
power supply. If not, contact an
electrician.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by our
Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not touch the mains cable or the
mains plug with wet hands.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Only for UK and Ireland: The appliance
has a 13 amp mains plug. If it is
necessary to change the fuse in the
mains plug, use a 13 amp ASTA (BS
1362) fuse.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Make sure not to cause damage to the
water hoses.
• Before you connect the appliance to
new pipes or pipes not used for a long
time, let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
Use
WARNING! Risk of injury,
electrical shock, fire, burns or
damage to the appliance.
• Obey the safety instructions on the
detergent packaging.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Make sure that you remove all metal
objects from the laundry.
• Do not put a container to collect
possible water leakage under the
appliance. Contact the Authorised
Service Centre to ensure which
accessories can be used.
• Do not use with an external remote-
control system or any other device that
switches on automatically.
Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
4
PRODUCT DESCRIPTION
Appliance overview
3
1
4
5
2
1
Control panel
2
Lid
3
Lid handle
4
Feet for the appliance level
5
Rating plate
CONTROL PANEL
Control panel description
RINÇAGE
PLUS
TEMPÉRATURE
RAPIDE
SUPER
RAPIDE
DÉPART / PAUSE
DÉPART DIFFÉRÉ
3H 6H 9H
RINÇAGE/ESSORAGE
PRÉ LAVAGE/LAVAGE
FIN
90°
60°
40°
OPTION
30°
COTON
COTON
+
PR
ÉLAVAGE
COTON ECO
+
PR
ÉLAVAGE
D
É
LICAT
LAINE
MIX 20
°
LAVAGE
À LA MAIN
+
PR
ÉLAVAGE
REPASSAGE
FACILE PLUS
COTON ECO
ARRÊT
VIDANGE
RINÇAGE
ESSORAGE
31
5678
4
1000
900
700
ESSORAGE
500
2
SYNTHÉTIQUE
SYNTH
ÉTIQUE
1
Programme knob
2
Spin speed selection knob
3
Delay start button (Départ Différé)
4
Indicators:
Prewash/Main wash phase (Prélavage/
Lavage)
Rinse/Spin phase (Rinçage/Essorage)
End of cycle (Fin)
5
Start/Pause button (Départ/Pause)
6
Extra rinse button (Rinçage Plus)
7
Options selection button (Option)
5
8
Temperature selection button
(Température)
PROGRAMME CHART
Programme
Temperature range
Maximum
load, Maxi-
mum spin
speed
Programme description (Type of load and soil
level)
Coton
90°C - Cold
5,5 kg
1000 rpm
White cotton and coloured cotton. Normal soil
and light soil.
Coton Eco
1)
90°C - 40°C
5,5 kg
1000 rpm
White cotton and colour-fast cotton. Normal
soil. The energy consumption decreases and the
time of the washing programme is extended.
Coton+Prélavage
90°C - Cold
5,5 kg
1000 rpm
White cotton and coloured cotton. Heavy soil
and normal soil.
Coton Eco+Prélavage
90°C - 40°C
5,5 kg
1000 rpm
White cotton and colour-fast cotton. Normal
soil with stains. The energy consumption decreases
and the time of the washing programme is exten-
ded.
Synthétique
60°C - Cold
2,5 kg
900 rpm
Synthetic items or mixed fabric items. Normal
soil.
Synthétique+Prélavage
60°C - Cold
2,5 kg
900 rpm
Synthetic items or mixed fabric items. Heavy
soil and normal soil.
Repassage Facile Plus
60°C - Cold
1 kg
900 rpm
Synthetic items to be gentle washed. Normal
and light soil.
2)
Délicat
40°C - Cold
2,5 kg
700 rpm
Delicate fabrics as acrylics, viscose, polyester
items. Normal soil.
Laine
30°C - Cold
1 kg
1000 rpm
Machine washable wool and hand washable
wool.
Lavage à la main
40°C - Cold
1 kg
1000 rpm
Delicate fabrics with «hand washing» care sym-
bol.
3)
Mix 20°
20°C
3 kg
900 rpm
Special programme for cotton, synthetic and mixed
fabrics with light soil. Set this programme to de-
crease the energy consumption. Make sure that the
detergent is for low temperature in order to have
good washing results
4)
.
Rinçage
Cold
5,5 kg
1000 rpm
To rinse and spin the laundry. All fabrics.
6
Programme
Temperature range
Maximum
load, Maxi-
mum spin
speed
Programme description (Type of load and soil
level)
Vidange 5,5 kg To drain the water in the drum. All fabrics.
Essorage 5,5 kg
1000 rpm
To rinse and spin the laundry. All fabrics.
1)
Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these
programmes with temperature selected 60°C and with temperature selected 40°C are respectively the «Standard
60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in
terms of combined energy and water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selec-
ted programme.
2)
To reduce the creases of the laundry, this cycle regulates the water temperature and performs a soft wash and
spin phase. The appliance adds some rinses.
3)
During this cycle the drum rotates slowly to ensure a gentle washing. It can seem that the drum doesn't rotate or
doesn't rotate properly. Consider this as a normal functioning of the appliance.
4)
The appliance performs the short heating phase if the water temperature is below 20°C. The appliance can show
the temperature setting as “cold”.
Programme options compatibility
Programme
Essorage
Rapide
Super Rapide
Rinçage Plus
Départ Différé
Coton ■ ■ ■ ■ ■ ■ ■
Coton Eco ■ ■ ■ ■ ■
Coton+Prélavage ■ ■ ■ ■ ■ ■ ■
Coton Eco+Prélavage ■ ■ ■ ■ ■
Synthétique ■ ■ ■ ■ ■ ■ ■
Synthétique+Prélavage ■ ■ ■ ■ ■ ■ ■
Repassage Facile Plus ■ ■ ■ ■ ■
Délicat ■ ■ ■ ■ ■ ■ ■
Laine ■ ■ ■ ■
Lavage à la main ■ ■ ■ ■
Mix 20° ■ ■ ■ ■ ■
7
Programme
Essorage
Rapide
Super Rapide
Rinçage Plus
Départ Différé
Rinçage ■ ■ ■ ■ ■
Vidange
Essorage ■ ■
CONSUMPTION VALUES
The data of this table are approximate. Different causes can change the da-
ta: the quantity and type of laundry, the water and ambient temperature.
Programmes Load
(kg)
Energy
consump-
tion (kWh)
Water
consump-
tion (litre)
Approxi-
mate pro-
gramme
duration
(minutes)
Remain-
ing mois-
ture (%)
1)
Coton 60 °C 5,5 1,15 58 133 60
Coton 40 °C 5,5 0,70 58 131 60
Synthétique 40 °C 2,5 0,55 46 102 37
Délicat 40 °C 2,5 0,55 46 90 37
Laine/Lavage à la
main 30 °C
2)
1 0,35 52 56 32
Standard cotton programmes
Standard 60 °C
cotton
5,5 0,96 47 214 60
Standard 60 °C
cotton
2,75 0,81 33 165 60
Standard 40 °C
cotton
2,75 0,59 33 129 60
1)
At the end of spin phase.
2)
Not available for some models.
Off Mode (W) Left On Mode (W)
0,10 0,98
8
Off Mode (W) Left On Mode (W)
The information given in the chart above are in compliance with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC.
OPTIONS
Essorage
With this knob you can set the spin speed.
For the maximum spin speeds see
"Programmes".
You can also set additional options.
Additional spin options:
No spin
• Set this option to deactivate all spin
phases. Only the drain phase is
available.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for
some washing programmes.
Rinse hold
• Set this option to prevent the laundry
creases.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the
laundry creases.
• The lid stays locked. You must drain the
water to unlock the lid.
To drain the water refer to ‘At
the end of the programme’.
Température
With this option you can change the default
temperature.
Indicator = cold water
The indicator of the set temperature comes
on.
Rapide
With this option you can decrease the
programme duration.
Use this option for items with daily soil.
The related indicator comes on.
Super Rapide
With this option you can decrease the
programme duration.
Use this option for items with light soil or
items to refresh.
The related indicator comes on.
Rinçage Plus
With this option you can add some rinses
to a washing programme.
Use this option for persons allergic to
detergents and in areas where the water is
soft.
The related indicator comes on.
Départ Différé
With this option you can delay the start of a
programme by 9, 6 or 3 hours.
The indicator of the set value is on.
BEFORE FIRST USE
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at
the highest temperature without
laundry.
This removes all possible dirt from the drum
and the tub.
9
DAILY USE
WARNING! Refer to Safety
chapters.
Loading the laundry
1. Open the appliance lid.
2. Push the button A.
The drum opens automatically.
3. Put the laundry in the drum, one item at
a time.
4. Shake the items before you put them in
the appliance.
Make sure not to put too much laundry in
the drum.
5.
Close the drum and the lid.
A
CAUTION! Before you close the
lid of your appliance, make sure
that you close the drum
correctly.
Using detergent and additives
Measure out the detergent and the fabric
conditioner.
Detergent compartments
Detergent compartment for
washing phase.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION! Do
not exceed the
MAX level.
When you set a prewash option, put the de-
tergent for prewash phase directly into the
drum.
Setting a programme
1.
Turn the programme knob and set the
programme:
• The indicator of the button Départ/
Pause flashes.
2.
If necessary, change the spin speed or
add available options. When you
activate an option, the indicator of the
set option comes on.
If you set something incorrect,
the indicator of button Départ/
Pause flashes red.
Starting a programme without
the delay start
Press the button Départ/Pause .
• The indicator of this button stops to
flash and stays on.
• The programme starts, the lid locks,
the indicator of the current cycle
phase is on.
• The drain pump can operate for a
short time at the beginning of the
washing cycle.
Starting a programme with the
delay start
1. Press the button Départ Différé to set
the hours of delay you want to set.
The indicator of the set delay is on.
2. Press the button Départ/Pause:
10
• The appliance starts the countdown.
• When the countdown is completed,
the programme starts automatically.
You can cancel or change the
set of the delay start before you
press the button Départ/Pause.
To cancel the delay start:
1. Press the button Départ/Pause to set
the appliance to pause.
2. Press Départ Différé until the indicator
of the set delay goes off.
Press Départ/Pause again to start the
programme immediately.
Interrupting a programme and
changing the options
You can change only some options before
they operate.
1.
Press the button Départ/Pause . The
indicator flashes.
2.
Change the options.
3.
Press the button Départ/Pause again.
The programme continues.
Opening the lid
While a programme operates or the delay
start operates, the appliance lid is locked.
CAUTION! If the temperature
and level of the water in the
drum are too high, you cannot
open the lid.
Open the lid during the first 10 minutes
of the cycle and when the delay start
operates:
1. Press the button Départ/Pause to
pause the appliance.
2. Wait a couple of minutes and then you
can open a lid.
3. Close the lid and press button Départ/
Pause again. The programme
continues (or the delay start).
Open the lid when the programme
operates:
1. Turn the programme knob to position
Arrêt to deactivate the appliance.
2. Wait for some minutes and then open
the appliance lid.
3. Close the lid and set the programme
again.
Cancelling a running
programme
1. Turn the programme knob to position
Arrêt to cancel the programme and to
deactivate the appliance.
2. Turn the programme knob again to
activate the appliance. Now, you can
set a new washing programme.
Before starting the new
programme the appliance could
drain the water. in this case,
make sure that the detergent is
still in the detergent
compartment, if not fill the
detergent again.
At the end of the programme
• The appliance stops automatically.
• The indicator of the button Départ/
Pause goes off.
• The indicator Fin is on.
• You can open the lid.
• Remove the laundry from the appliance.
Make sure that the drum is empty. Close
the water tap.
• Turn the programme knob to position
Arrêt to deactivate the appliance.
• Keep the lid ajar, to prevent the mildew
and odours.
The washing programme is completed,
but there is water in the drum:
• The drum turns regularly to prevent the
creases in the laundry.
• The indicator of button Départ/Pause
flashes. The lid stays locked.
• You must drain the water to open the lid.
To drain the water:
1. Set a "Drain" or a "Spin" programme. If
necessary, decrease the spin speed.
2. Press the button Départ/Pause. The
appliance drains the water and spins.
3. When the programme is completed,
after a couple of minutes, you can open
the lid.
4. Turn the programme knob to position
Arrêt to deactivate the appliance.
11
Stand by
Some minutes after the end of the washing
programme, if you do not deactivate the
appliance, the energy saving status
activates. The energy saving status
decreases the energy consumption when
the appliance is on the standby:
• All indicators go off.
• The indicator of the button Départ/Pause
flashes slowly.
Press one of the buttons to deactivate the
energy saving status.
HINTS AND TIPS
The laundry load
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are
on the laundry care labels.
• Do not wash together white and
coloured items.
• Some coloured items can discolour with
the first wash. We recommend that you
wash them separately for the first times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn inside out multilayered fabrics, wool
and items with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy soil
stains.
• Be careful with the curtains. Remove the
hooks or put the curtains in a washing
bag or pillowcase.
• Do not wash in the appliance laundry
without hems or with cuts. Use a
washing bag to wash small and/or
delicate items (e.g. underwired bras,
belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase. If this
occurs, adjust manually the items in the
tub and start the spin phase again.
Stubborn stains
For some stains, water and detergent is not
sufficient.
We recommend that you remove these
stains before you put the items in the
appliance.
Special stain removers are available. Use
the special stain remover that is applicable
to the type of stain and fabric.
Detergents and additives
• Only use detergents and additives
specially made for washing machines:
– powder detergents for all types of
fabric,
– powder detergents for delicate
fabrics (40 °C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60
°C max) for all types of fabric, or
special for woollens only.
• Do not mix different types of detergents.
• To help the environment, do not use
more than the correct quantity of
detergent.
• Obey the instructions that you find on
the on packaging of these products.
• Use the correct products for the type
and colour of the fabric, the programme
temperature and the level of soil.
• If your appliance has not the detergent
dispenser with the flap device, add the
liquid detergents with a dosing ball
(supplied by the detergent's
manufacturer).
Ecological hints
• Set a programme without the prewash
phase to wash laundry with normal soil.
• Always start a washing programme with
the maximum load of laundry.
• If necessary, use a stain remover when
you set a programme with a low
temperature.
12
• To use the correct quantity of the
detergent, check the water hardness of
your domestic system
Water hardness
If the water hardness in your area is high or
moderate, we recommend that you use a
water softener for washing machines. In
areas where the water hardness is soft it is
not necessary to use a water softener.
To know the water hardness in your area,
contact your local water authority.
Use the correct quantity of the water
softener. Obey the instructions that you find
on the packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
External cleaning
Clean the appliance only with soap and
warm water. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
Descaling
If the water hardness in your area is high or
moderate, we recommend that you use a
water descaling product for washing
machines.
Regularly examine the drum to prevent
limescale and rust particles.
To remove rust particles use only special
products for washing machine. Do this
separately from the laundry wash.
Always obey the instructions
that you find on the packaging
of the product.
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the
drum. Make regularly a maintenance wash.
To do this:
• Remove the laundry from the drum.
• Set the cotton programme with the
highest temperature with a small
quantity of detergent.
Lid seal
Regularly examine the seal. Clean it when
needed, using ammonia cream cleanser
agent without scratching the seal surface,
Always obey the instructions
that you find on the packaging
of the product.
13
Cleaning the detergent dispenser
1.
1
2
2.
2
1
Cleaning the inlet hose and the valve filter
1.
1
2
3
2.
3. 4.
90˚
14
Cleaning the drain filter
1.
4
3
5
6
2
1
2.
1
2
3
CLACK
4
CLACK
Frost precautions
If the appliance is installed in an area where
the temperature can be less than 0 °C,
remove the remaining water from the inlet
hose and the drain pump.
Do this procedure also when
you want to do the emergency
drain.
1. Close the water tap and disconnect the
water inlet hose.
2. Disconnect the drain hose from a sink
or spigot.
3.
Put the ends of the drain and inlet hose
in a container. Let the water flow out of
the hoses.
4. Set the Drain programme and let it
operate until the end of the cycle.
5. Turn the programme knob to Stop to
disconnect the appliance from the
power supply.
6. Disconnect the appliance.
WARNING!
Make sure that the temperature is more
than 0 °C before you use the appliance
again. The manufacturer is not responsible
for damages caused by low temperatures.
TECHNICAL DATA
Dimension Width/ Height/ Depth/ To-
tal depth
400 mm/ 890 mm/ 600 mm/ 600 mm
Electrical connection Voltage
Overall power
Fuse
Frequency
230 V
2300 W
10 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except
where the low voltage equipment has no protection
against moisture
IPX4
15
Water supply pressure Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Water supply
1)
Cold water
Maximum Load Cotton 5,5 kg
Energy Efficiency Class A+
Spin Speed Maximum 1000 rpm
1)
Connect the water inlet hose to a water tap with a 3/4'' thread.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
Introduction
The start of the appliance does not occur or
it stops during operation.
First try to find a solution to the problem
(refer to the table). If not, contact the
Authorised Service Centre.
The red indicator of button Départ/Pause
flashes.
WARNING! Deactivate the
appliance before you do the
checks.
Possible failures
Problem Possible solution
The programme does not
start.
• Make sure that the mains plug is connected to the mains sock-
et.
• Make sure that the appliance lid is closed.
• Make sure that there is not a damaged fuse in the fuse box.
• Make sure that the Start/Pause has been pressed.
• If the delay start is set, cancel the setting or wait for the end of
countdown.
• Deactivate the Child Lock function if it is on (if available).
The appliance does not
fill with water properly.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low.
For this information, contact your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter of the inlet hose and the filter of the
valve are not clogged. Refer to “Care and cleaning”.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the connection of the water inlet hose is correct.
• Make sure that the drain hose is in the correct position. The
hose may be too low.
16
Problem Possible solution
The appliance does not
drain the water.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the drain filter is not clogged. Clean the filter, if
necessary. Refer to 'Care and cleaning'.
• Make sure that the connection of the drain hose is correct.
• Set the drain programme if you set a programme without drain
phase.
• Set the drain programme if you set an option which ends with
water in the tub.
The spin phase does not
operate or the washing
cycle lasts longer than
usually.
• Set the spin programme.
• Make sure that the drain filter is not clogged. Clean the filter, if
necessary. Refer to 'Care and cleaning'.
• Adjust manually the items in the tub and start the spin phase
again. This problem may be caused by balance problems.
There is water on the
floor.
• Make sure that the couplings of the water hoses are tight and
there is not water leakages.
• Make sure that the drain hose have no damages.
• Make sure you use the correct detergent and the correct quan-
tity of it.
You cannot open the ap-
pliance lid.
• Make sure that the washing programme is finished.
• Set the drain or the spin programme if there is water in the
drum.
The appliance makes an
unusual noise.
• Make sure the levelling of the appliance is correct. Refer to 'In-
stallation'.
• Make sure that the packaging and/or the transit bolts are re-
moved. Refer to 'Installation'.
• Add more laundry in the drum. The load may be too small.
The washing results are
not satisfactory.
• Increase the detergent quantity or use a different detergent.
• Use special products to remove the stubborn stains before you
wash the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
You cannot set an option. • Make sure that you press only the wanted button(s).
After the check, activate the appliance. The
programme continues from the point of
interruption.
If the problem occurs again, contact the
Authorised Service Centre.
If the display shows other alarm codes.
Deactivate and activate the appliance. If the
problem continues, contact the Service.
INSTALLATION
WARNING! Refer to Safety
chapters.
17
Unpacking
1.
2
1
2.
1
2
1
2
3.
18
Positioning Water supply
3/4”
3/4”
1/2”
3/4”
FI
SE
NO
DK
90
O
90
O
1
1
22
Drainage
min.600 mm
max.1000 mm
FICHE PRODUIT
FICHE PRODUIT
1)
Marque
Curtiss
Référence du modèle
ETL 1055 D
Capacité de lavage nominale (coton)
5,5 kg
19
Classe d'efficacité énergétique
A+
Consommation énergétique annuelle pondérée
2)
176 kWh/an
"Consommation énergétique dans le cas du programme
standard Coton (60 °C, pleine charge)"
0,96 kWh
"Consommation énergétique dans le cas du programme
standard Coton (60 °C, demi-charge)"
0,81 kWh
"Consommation énergétique dans le cas du programme
standard Coton (40 °C, demi-charge)"
0,59 kWh
Puissance consommée - mode Arrêt
0,10 W
Puissance consommée - en mode marche
0,98 W
Consommation d'eau annuelle pondérée
2)
9490 l/an
Classe d'efficacité d'essorage
C
Vitesse d'essorage maximale (coton)
1000 tr/min
Taux d'humidité résiduel (programme standard Coton, 60 °C,
pleine charge)
60 %
"Durée du programme standard Coton (60 °C, pleine charge)"
214 min
"Durée du programme standard Coton (60°C, demi-charge)"
165 min
"Durée du programme standard Coton (40°C, demi-charge)"
129 min
Durée en mode marche
5 min
Émissions acoustiques dans l'air en phase lavage
58 dB
Émissions acoustiques dans l'airen phase essorage
75 dB
1)
Les données sont fournies conformément à l'Annexe II de la réglementation (EU) N° 1061/2010
2)
Consommation d’énergie et d'eau sur la base de 220 cycles de lavage standard par an pour les programmes
coton à 60 °C et à 40 °C à pleine charge et à demi-charge, et de la consommation des modes à faible puissance. La
consommation réelle d’énergie dépend des conditions d’utilisation de l’appareil. Information sur les indications
notées sur l’étiquette énergétique : Les programmes correspondants aux tests d’économie d’énergie sont ‘coton
standard 40°C et coton standard 60°C’. Ces programmes conviennent pour nettoyer du linge en coton normale-
ment sale et sont les programmes les plus ef-ficaces en termes de consommation combinée d’eau et d’énergie.
ENVIRONMENT CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable containers
to recycle it. Help protect the environment
and human health and to recycle waste of
electrical and electronic appliances. Do not
dispose appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
20
*
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Iee ETL1055D Manuel utilisateur

Iee
Marque
Iee
Modèle
ETL1055D
Catégorie
Machines à laver
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents