ARTHUR MARTIN ELECTROLUX AWT1274AOW Manuel utilisateur

Marque: ARTHUR MARTIN ELECTROLUX

Modèle: AWT1274AOW

Catégorie: Machines à laver

Taper: Manuel utilisateur

AWT1274AOW

EN Washing Machine User Manual 2

FR Lave-linge Notice d'utilisation 24

CONTENTS

Safety information 2

Safety instructions 3

Product description 5

Control panel 5

Programme Chart 6

Consumption values 9

Options 10

Settings 12

Before first use 12

Daily use 12

Hints and tips 16

Care and cleaning 17

Troubleshooting 20

Technical Data 22

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damages that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Children between 3 and 8 years of age and persons with

very extensive and complex disabilities shall be kept away

unless continuously supervised.

• Children of less than 3 years of age should be kept away

unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• Do not change the specification of this appliance.

• Do not exceed the maximum load of 7 kg (refer to the

"Programme chart" chapter).

• The operating water pressure at the water entry point from

the outlet connection must be between 0.5 bar (0.05 MPa)

and 8 bar (0.8 MPa).

• The ventilation opening in the base must not be covered

by a carpet, mat, or any floor covering.

• The appliance must be connected to the water mains using

the new supplied hose sets, or other new hose sets

supplied by the Authorised Service Centre.

• Old hose sets must not be reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service

Centre or similarly qualified persons to avoid an electrical

hazard.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to

clean the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

SAFETY INSTRUCTIONS

Installation

The installation must comply

with relevant national

regulations.

• Remove all the packaging and the

transit bolts including rubber bush with

plastic spacer.

• Keep the transit bolts in a safe place. If

the appliance is to be moved in the

future they must be reattached to lock

the drum to prevent an internal

damage.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Do not install or use the appliance

where the temperature can be less

than 0°C or where it is exposed to the

weather.

• The floor area on which the appliance

is to be installed must be flat, stable,

heat resistant and clean.

• Make sure that there is air circulation

between the appliance and the floor.

• Do not install the appliance directly

above a floor drain.

• Adjust the feet to have the necessary

space between the appliance and the

flooring.

• Do not install the appliance where the

appliance lid cannot be fully opened.

• Do not put a container to collect

possible water leakage under the

appliance. Contact the Authorised

Service Centre to ensure which

accessories can be used.

Electrical connection

WARNING! Risk of fire and

electric shock.

• The appliance must be earthed.

• Always use a correctly installed

shockproof socket.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not touch the mains cable or the

mains plug with wet hands.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• This appliance complies with the E.E.C.

Directives.

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let

the water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of

the appliance.

• Do not use an extension hose if the

inlet hose is too short. Contact the

service centre for the replacement of

the inlet hose.

• You can extend the drain hose to

maximum 400 cm. Contact the service

centre for the other drain hose and the

extension.

Use

WARNING! Risk of injury,

electric shock, fire, burns or

damage to the appliance.

• This appliance is for household use

only.

• Follow the safety instructions on the

detergent packaging.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

• Make sure that all metal objects are

removed from the laundry.

• Do not wash fabrics which are heavily

soiled with oil, grease or other greasy

substances. It can damage rubber

parts of the washing machine. Prewash

such fabrics by hand before loading

them into the washing machine.

Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains electrical and water supplies.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Remove the door catch to prevent

children or pets from becoming trapped

in the drum.

• Dispose of the appliance in accordance

with local requirements for the disposal

of Waste Electrical and Electronic

Equipment (WEEE).

PRODUCT DESCRIPTION

Appliance overview

Control panel

Lid

Lid handle

Drain pump filter

Feet for levelling the appliance

Rating plate

CONTROL PANEL

Control panel description

Essorage

Température

Rinçage

Plus

Départ

Différé

Départ/Pause

Pré-

lavage

Rinçage

Essorage

Vidange

Blanc/Couleurs

Coton Eco

Synthétiques

Chemises

Sport

Rideaux

Jeans

Couette

Soie

Laine/Lavage

à la main

Délicats

90° 60° 40°

30° 20°

1200 800 400

Repassage

Facile

1 2 3 4

910

Programme knob

Spin reduction touchpad

(Essorage)

Temperature touchpad

(Température)

Display

Prewash touchpad (Prélavage)

Delay start touchpad (Départ

Différé)

Extra rinse touchpad (Rinçage

Plus)

Easy iron touchpad (Repassage

Facile)

Start/Pause touchpad (Départ/

Pause)

Time Manager touchpads

Display

A B

E D

A. The time area:

• Programme time.

• The alarm codes. Refer to the

chapter “Troubleshooting” for their

description.

• The level of the Time Manager

B. The Delay Start indicator.

C. The Child Lock indicator.

D. The Lid Lock indicator:

• It is on, you cannot open the lid.

• It is off, you can open the lid.

• It flashes, you cannot open the lid.

Wait for some minutes until the

indicator is off.

E. Washing phase indicators.

• : the washing phase

• : the rinses phase

• : the spin phase

PROGRAMME CHART

Programme

Temperature

range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Blanc/

Couleurs

90°C - Cold

7 kg

1200 rpm

White cotton and coloured cotton. Normal soil and

light soil.

Programme

Temperature

range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Coton

Eco

60°C- 40°C

7 kg

1200 rpm

White cotton and fast-coloured cotton. Normal soil.

The energy consumption decreases and the time of

the washing programme is extended.

Synthé‐

tiques

60°C - Cold

3 kg

1200 rpm

Synthetic items or mixed fabric items. Normal soil.

Délicats

40°C - Cold

2,5 kg

1200 rpm

Delicate fabrics such as acrylics, viscose and

mixed fabrics requiring gentler washing. Normal

soil.

Laine/

Lavage à la

main

40°C - Cold

1 kg

1200 rpm

Machine washable wool, hand washable wool and

other fabrics with «hand washing» care symbol

Soie

30°C

1 kg

800 rpm

Special programme for silk and mixed synthetic

items.

Couette

60°C- 30°C

2 kg

800 rpm

Special programme for one synthetic blanket, du‐

vet, bedspread and so on.

Rinçage

Cold

7 kg

1200 rpm

To rinse and spin the laundry. All fabrics, except

woollens and very delicate fabrics. Reduce the spin

speed accordingly to the type of laundry.

Vidange

7 kg To drain the water in the drum. All fabrics.

Essorage

7 kg

1200 rpm

To spin the laundry and to drain the water in the

drum. All fabrics, except woollens and delicate

fabrics.

Jeans

60°C- Cold

3 kg

1200 rpm

Items in denim and jersey. Also for dark coloured

items.

Rideaux

40°C - Cold

3 kg

800 rpm

Special programme for curtains. The prewash phase

is activated automatically.

Sport

30°C

2,5 kg

800 rpm

Synthetic and delicate items. Light soil items or

items to refresh.

Programme

Temperature

range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Chemises

30°C

1,5 kg

800 rpm

Synthetic and mixed fabric items. Light soil items

and items to freshen up. For 5 - 6 shirts.

Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,

these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐

gramme». They are the most efficient programmes in terms of combined energy and water consumption for

washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the se‐

lected programme.

During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or

doesn't rotate properly, but this is normal for this programme.

Do not use any detergent for prewash phase to rinse only with water.

Programme options compatibility

Programme

■ ■ ■ ■ ■ ■ ■ ■

■ ■ ■ ■ ■ ■

■ ■ ■ ■ ■ ■ ■ ■

■ ■ ■ ■ ■ ■ ■

■ ■ ■ ■ ■

■ ■ ■

■ ■

■ ■ ■ ■ ■

■

■ ■

■ ■ ■ ■ ■ ■

■ ■ ■ ■ ■

■ ■ ■

Woolmark Apparel Care - Blue

The wool wash cycle of this machine has been

approved by The Woolmark Company for the

washing of wool garments labelled as «hand

wash» provided that the garments are washed

according to the instructions issued by the

manufacturer of this washing machine. Follow

the garment care label for drying and other

laundry instructions. M1145

The Woolmark symbol is a Certification mark

in many countries.

CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant stand‐

ards. Different causes can change the data: the quantity and type of laun‐

dry and ambient temperature. Water pressure, the supply voltage and the

temperature of inlet water may also affect the washing programme dura‐

tion.

Technical specifications may be changed without prior notice to improve

the quality of product.

At the start of the programme, the display shows the programme duration

for the maximum load capacity.

During the washing phase the programme duration is automatically cal‐

culated and can be greatly reduced if the laundry load is lower than the

maximum load capacity (e.g. Cotton 60°C, maximum load capacity 7 kg,

the programme duration exceeds 2 hours; actual load 1 kg, the pro‐

gramme duration will be less than 1 hour).

When the appliance is calculating the real programme duration a dot

flashes in the display.

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

Blanc/Couleurs

60°C

7 1,16 58 197 53

Blanc/Couleurs

40°C

7 0,61 56 192 53

Synthétiques

40°C

3 0,45 46 105 35

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

Délicats

40°C

2,5 0,55 46 90 35

Laine/Lavage à la

main

30°C

1 0,35 50 65 30

Standard cotton programmes

Standard 60°C cot‐

ton

7 1,08 46 259 53

Standard 60°C cot‐

ton

3,5 0,70 39 179 53

Standard 40°C cot‐

ton

3,5 0,65 39 179 53

At the end of spin phase.

Not available for some models.

Off Mode (W) Left On Mode (W)

0.48 0.48

The information given in the chart above is compliant with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC

OPTIONS

Température

Set this option to change the default

temperature.

Indicator = cold water.

The indicator of the set temperature

comes on.

Essorage

With this option you can change the

default spin speed.

The indicator of the set speed comes on.

Additional spin options:

No Spin

• Set this option to deactivate all spin

phases. Only the drain phase is

available.

• The related indicator comes on.

• Set this option for very delicate fabrics.

• The rinses phase uses more water for

some washing programmes.

Rinse Hold

• Set this option to prevent the laundry

creases.

• The related indicator comes on.

• There is a water in the drum when the

programme is completed.

• The drum turns regularly to prevent the

laundry creases.

• The lid stays locked. You must drain

the water to unlock the lid.

To drain the water refer to ‘At

the end of the programme’.

Night Cycle

• Set this option to remove all spin

phases and to perform a silent

washing.

• The rinse phase uses more water for

some washing programmes.

• The related indicator comes on.

• The washing programme stops with the

water in the drum. The drum turns

regularly to prevent the laundry

creases.

• The lid stays locked. You must drain

the water to unlock the lid.

To drain the water refer to ‘At

the end of the programme’.

Prélavage

With this option you can add a prewash

phase to a washing programme.

Use this option for heavy soil.

When you set this option the programme

duration increases.

The related indicator comes on.

Départ Différé

With this option you can delay the start of

a programme from 30 minutes to 20

hours.

The display shows the related indicator.

Rinçage Plus

With this option you can add some rinses

to a washing programme.

Use this option for persons allergic to

detergents and in areas where the water

is soft.

The related indicator comes on.

Repassage Facile

The appliance carefully washes and spins

the laundry to prevent the creases.

The appliance decreases the spin speed,

uses more water and adapts the

programme duration to the type of

laundry.

The related indicator comes on.

Time Manager

When you set a washing programme, the

display shows the default duration.

Press or to decrease or increase the

programme duration.

The Time Manager is available only with

the programmes in the table.

indica‐

tor

)

■

■ ■ ■ ■

■ ■ ■ ■ ■ ■

■

■ ■ ■ ■

■

)

■

)

■

)

■

)

■

)

If available.

Shortest: to freshen the laundry.

Longest: Increasing the programme duration gradu‐

ally decreases the energy consumption. The optimized

heating phase saves energy and the longer duration

maintains the same washing results (specially for nor‐

mal soil).

Defaullt duration for all programmes.

SETTINGS

Child Lock

With this option you can prevent that the

children play with the control panel.

• To activate/deactivate this option,

press and at the same time

until the indicator comes on/goes

off.

You can activate this option:

• After you press : the options and

the programme knob are locked.

• Before you press : the appliance

cannot start.

Acoustic signals

The acoustic signals operate when:

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic

signals, press and at the same

time for 6 seconds.

If you deactivate the acoustic

signals, they continue operate

when the appliance has a

malfunction.

BEFORE FIRST USE

1. Connect the mains plug to the mains

socket.

2. Open the water tap.

3. Put 2 litre of water in the detergent

compartment for washing phase.

This activates the drain system.

4. Put a small quantity of detergent in the

compartment for washing phase.

5. Set and start a programme for cotton

at the highest temperature without

laundry.

This removes all possible dirt from the

drum and the tub.

DAILY USE

WARNING! Refer to Safety

chapters.

Loading the laundry

1. Open the appliance lid.

2. Push the button A.

The drum opens automatically.

3. Put the laundry in the drum, one item

at a time.

4. Shake the items before you put them

in the appliance.

Make sure not to put too much laundry in

the drum.

5. Close the drum and the lid.

CAUTION! Before you close

the lid of your appliance, make

sure that you close the drum

correctly.

Detergent compartments. Using

detergent and additives

1. Measure out specified detergents for

washing machine the detergent and the

fabric conditioner.

2. Put the detergent and the fabric

conditioner into the proper compartments.

Always obey the instructions

that you find on the packaging

of the detergent products.

Detergent compartment for prewash

phase.

The marks MAX are the maximum

levels of the quantity of detergent

(powder or liquid).

Detergent compartment for washing

phase.

The marks MAX are the maximum

levels of the quantity of detergent

(powder or liquid).

Compartment for liquid additives

(fabric conditioner, starch).

The mark

is the maximum level

for the quantity liquid additives.

Flap for powder or liquid detergent.

Liquid or powder detergent

CLICK

• Position A for powder detergent (factory setting).

• Position B for liquid detergent.

When you use the liquid detergent:

• Do not use gelatinous or thick liquid detergents.

• Do not put more liquid then the maximum level.

Setting a programme

1. Turn the programme knob and set the

programme:

• The indicator flashes.

• The display shows the level of the

Time Manager, the programme

duration and the indicators of the

phases of the programme.

2. If necessary, change the temperature

and the spin speed or add available

options. When you activate an option,

the indicator of the set option comes

on.

If you set something incorrect,

the display shows the message

Starting a programme without

the delay start

Press .

• The indicator of stops to flash

and stays on.

• The indicator starts to flash on

the display.

• The programme starts, the lid locks,

the display shows the indicator .

• The drain pump can operate for a

short time when the appliance fills

water.

After approximately 15 minutes

from the start of the

programme:

• The appliance adjusts

automatically the

programme duration agree

with the laundry load.

• The display shows the new

value.

Starting a programme with the

delay start

1. Press again and again until the

display shows the delay you want to

set.

The related indicator comes on the

display.

2. Press :

• The appliance starts the

countdown.

• The door locks, the display shows

the indicator .

• When the countdown is completed,

the programme starts automatically.

You can cancel or change the

set of the delay start before you

press the . To cancel the

delay start:

• Press to set the

appliance to pause.

• Press until the

display shows '.

• Press again to start

the programme

immediately.

Interrupting a programme and

changing the options

You can change only some options before

they operate.

1. Press .

The indicator flashes.

2. Change the options.

3. Press again.

The programme continues.

Cancelling a running

programme

1. Turn the programme knob to position

to cancel the programme and to

deactivate the appliance.

2. Turn the programme knob again to

activate the appliance. Now, you can

set a new washing programme.

Before starting the new

programme the appliance could

drain the water. In this case,

make sure that the detergent is

still in the detergent

compartment, if not fill the

detergent again.

Opening the lid

While a programme or the delay start

operates, the appliance lid is locked. The

display shows the indicator .

CAUTION! If the temperature

and level of the water in the

drum are too high, you cannot

open the lid.

Open the lid when the delay start

operates:

1. Press the to pause the appliance.

2. Wait until the lid lock indicator

goes off.

3. You can open the lid.

4. Close the lid and press the again.

The delay start continues to operate.

Open the lid when the programme

operates:

1. Turn the programme knob to position

to deactivate the appliance.

2. Wait for some minutes and then open

the appliance lid.

3. Close the lid and set the programme

again.

At the end of the programme

• The appliance stops automatically.

• The acoustic signal operates (if it is

activated).

• In the display comes on.

• The indicator of the goes off.

• The lid lock indicator goes off.

• You can open the lid.

• Remove the laundry from the

appliance. Make sure that the drum is

empty.

• Close the water tap.

• Turn the programme knob to position

to deactivate the appliance.

• Keep the lid ajar, to prevent the mildew

and odours.

The washing programme is completed,

but there is water in the drum:

• The drum turns regularly to prevent the

creases in the laundry.

• The lid lock indicator is on. The

indicator flashes. The lid stays

locked.

• You must drain the water to open the

lid.

To drain the water:

1. If necessary, decrease the spin speed.

If you set , the appliance only

drains.

2. Press . The appliance drains the

water and spins.

3. When the programme is completed

and the lid lock indicator goes off,

you can open the lid.

4. Turn the programme knob to position

to deactivate the appliance.

The appliance drains and spins

automatically after

approximately 18 hours (except

for Wool programme).

Stand-by

Some minutes after the end of the

washing programme, if you do not

deactivate the appliance, the energy

saving status activates.

The energy saving status decreases the

energy consumption when the appliance

is on the stand by.

• All indicators and the display go off.

• The indicator of the flashes slowly

• Press one of the options to deactivate

the energy saving status.

If you set a programme or an

option that ends with water in

the drum, the energy saving

status function doesn't

activate to remind you to drain

the water.

HINTS AND TIPS

The laundry load

• Divide the laundry in: white, coloured,

synthetics, delicates and wool.

• Obey the washing instructions that are

on the laundry care labels.

• Do not wash white and coloured items

together.

• Some coloured items can discolour

with the first wash. We recommend that

you wash them separately for the first

times.

• Button up pillowcases, close zippers,

hooks and poppers. Tie up belts.

• Empty the pockets and unfold the

items.

• Turn multilayered fabrics, wool and

items with painted illustrations inside

out.

• Remove hard stains with a special

detergent.

• Wash and pre-treat heavy soil stains

before putting items in drum

• Be careful with the curtains. Remove

the hooks and put the curtains in a

washing bag or pillowcase.

• Do not wash laundry without hems or

with cuts. Use a washing bag to wash

small and/or delicate items (e.g.

underwired bras, belts, tights, etc. ).

• A very small load can cause balance

problems with the spin phase. If this

occurs, adjust manually the items in the

tub and start the spin phase again.

Stubborn stains

For some stains, water and detergent is

not sufficient.

We recommend that you pre-treat these

stains before you put the items in the

appliance.

Special stain removers are available. Use

the special stain remover that is applicable

to the type of stain and fabric.

Detergents and additives

• Only use detergents and additives

specially made for washing machines:

– powder detergents for all types of

fabric,

– powder detergents for delicate

fabrics (40 °C max) and woollens,

– liquid detergents, preferably for low

temperature wash programmes (60

°C max) for all types of fabric, or

special for woollens only.

• Do not mix different types of

detergents.

• To help the environment, do not use

more than the correct quantity of

detergent.

• Obey the instructions that you find on

the on packaging of these products.

• Use the correct products for the type

and colour of the fabric, the programme

temperature and the level of soil.

• If your appliance does not have the

detergent dispenser with the flap

device, add the liquid detergents with a

dosing ball (supplied by the detergent's

manufacturer).

Ecological hints

• Set a programme without the prewash

phase to wash laundry with normal soil.

• Always start a washing programme

with the maximum load of laundry

allowed.

• If necessary, use a stain remover when

you set a programme with a low

temperature.

• To use the correct quantity of

detergent, check the water hardness of

your domestic system. Refer to "Water

hardness".

Water hardness

If the water hardness in your area is high

or moderate, we recommend that you use

a water softener for washing machines. In

areas where the water hardness is soft it

is not necessary to use a water softener.

To know the water hardness in your area,

contact your local water authority.

Use the correct quantity of the water

softener. Obey the instructions that you

find on the packaging of the product.

CARE AND CLEANING

WARNING! Refer to Safety

chapters.

External cleaning

Clean the appliance with soap and warm

water only. Fully dry all the surfaces.

CAUTION! Do not use alcohol,

solvents or chemical products.

Descaling

If the water hardness in your area is high

or moderate, we recommend that you use

a water descaling product for washing

machines.

Regularly examine the drum to prevent

limescale and rust particles.

To remove rust particles use only special

products for washing machines. Do this

separately from the laundry wash.

Always obey the instructions

that you find on the packaging

of the product.

Maintenance wash

With the low temperature programmes it is

possible that some detergent stays in the

drum. Perform a maintenance wash

regularly. To do this:

• Remove all laundry from the drum.

• Select the cotton programme with the

highest temperature with a small

quantity of detergent.

Cleaning the detergent dispenser

1. 2.

Cleaning the drain filter

Do not clean the drain filter if the water in the appliance is hot.

1. 2.

3. 4.

Cleaning the inlet hose and the valve filter

3. 4.

90˚

Frost precautions

If the appliance is installed in an area

where the temperature can be less than 0

°C, remove the remaining water from the

inlet hose and the drain pump.

Do this procedure also when

you want to do the emergency

drain.

1. Close the water tap and disconnect the

water inlet hose.

2. Disconnect the drain hose from a sink

or spigot.

3. Put the ends of the drain and inlet

hose in a container. Let the water flow

out of the hoses.

4. Set the Drain programme and let it

operate until the end of the cycle.

5. Turn the programme knob to Stop to

disconnect the appliance from the

power supply.

6. Disconnect the appliance.

WARNING! Make sure that the

temperature is more than 0°C

before you use the appliance

again. The manufacturer is not

responsible for damages

caused by low temperatures.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

Introduction

The appliance does not start or it stops

during operation.

First try to find a solution to the problem

(refer to the table). If the problem persists,

contact the Authorised Service Centre.

With some problems, the acoustic

signals operate and the display shows

an alarm code:

• - The appliance does not fill with

water properly. Start the appliance

again by pressing Départ/Pause button.

After 10 seconds the door will be

unlocked.

• - The appliance does not drain

the water.

• - The appliance lid or drum doors

are open or not closed correctly.

Please check both!

• - The mains supply is unstable.

Wait until the mains supply is stable.

WARNING! Deactivate the

appliance before you do the

checks.

La page charge ...

ARTHUR MARTIN ELECTROLUX AWT1274AOW Manuel utilisateur

Marque: ARTHUR MARTIN ELECTROLUX

Modèle: AWT1274AOW

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: ARTHUR MARTIN ELECTROLUX AWT1274AOW User manual

Documents connexes

Arthur_Martin AWY61013WI Manuel utilisateur

ARTHUR MARTIN ELECTROLUX AWT1274AOW Manuel utilisateur

ARTHUR MARTIN ELECTROLUX AWT1274AOW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents