Jenn-Air Range ELECTRIC DOWNDRAFT SLIDE-IN RANGE Manuel utilisateur

Catégorie
Cuisinières
Taper
Manuel utilisateur
JENN-AIR
®
ELECTRIC DOWNDRAFT
SLIDE-IN RANGE
Form No. A/05/06 Part No. 8113P630-60 ©2006 Maytag Appliances Sales Co. All rights reserved. Litho U.S.A .
Important Safety Instructions.....................................1-4
Ducting Information...........................................................4
Care & Cleaning..............................................................5-8
Maintenance.....................................................................8-9
Troubleshooting .........................................................10-11
Surface Cooking.........................................................12-16
Oven Cooking..............................................................17-23
Options ..........................................................................24-28
Favorites...............................................................................29
Setup ..............................................................................30-32
Cartridges & Accessories ..............................................33
Warranty & Service...........................................................35
Guide d’utilisation et d’entretien.................................36
Guía de uso y cuidado....................................................72
USE & CARE
GUIDE
TABLE OF CONTENTS
®
8113P630-60 5/3/06, 8:59 AM1
1
Installer: Please leave this guide with this appliance.
Consumer: Please read and keep this guide for future
reference. Keep sales receipt and/or cancelled check as
proof of purchase.
Model Number__________________________________
Serial Number __________________________________
Date of Purchase ________________________________
If you have questions, call:
Jenn-Air Customer Assistance
1-800-JENNAIR (1-800-536-6247)
1-800-688-2080 (U.S. TTY for hearing or speech impaired)
(Mon.-Fri., 8 am-8 pm Eastern Time)
Internet: http://www.jennair.com
In our continuing effort to improve the quality and
performance of our cooking products, it may be necessary
to make changes to the appliance without revising this
guide.
For service information, see page 35.
IMPORTANT SAFETY
INSTRUCTIONS
Warning and Important Safety Instructions appearing
in this guide are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution, and care must be exercised when
installing, maintaining, or operating the appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
WARNING – Hazards or unsafe practices which
COULD result in severe personal injury or death.
CAUTION – Hazards or unsafe practices which
COULD result in minor personal injury.
WARNING
CAUTION
Read and follow all instructions before using this
appliance to prevent the potential risk of fire, electric
shock, personal injury or damage to the appliance as a
result of improper usage of the appliance. Use appliance
only for its intended purpose as described in this guide.
To ensure proper and safe operation: Appliance
must be properly installed and grounded by a qualified
technician. Do not attempt to adjust, repair, service,
or replace any part of your appliance unless it is
specifically recommended in this guide. All other
servicing should be referred to a qualified servicer.
Always disconnect power to appliance before servicing.
To check if device is properly installed, look underneath
range with a flashlight to make sure one of the rear
leveling legs is properly engaged in the bracket slot. The
anti-tip device secures the rear leveling leg to the floor
when properly engaged. You should check this anytime
the range has been moved.
To Prevent Fire or Smoke
Damage
Be sure all packing materials are removed from the
appliance before operating it.
Keep area around appliance clear and free from
combustible materials. Flammable materials should not
be stored in an oven.
Many plastics are vulnerable to heat. Keep plastics away
from parts of the appliance that may become warm or
hot.
To prevent grease fires, do not let cooking grease or
other flammable materials accumulate in or near the
appliance.
General Instructions
WARNING: To reduce risk of
tipping of the appliance from
abnormal usage or by excessive loading of the
oven door, the appliance must be secured by a
properly installed anti-tip device.
WARNING
ALL RANGES CAN TIP AND
CAUSE INJURIES TO PERSONS
INSTALL ANTI-TIP DEVICE
PACKED WITH RANGE
FOLLOW ALL INSTALLATION
INSTRUCTIONS
8113P630-60 5/3/06, 8:59 AM2
2
In Case of Fire
Turn off appliance and ventilating hood to avoid
spreading the flame. Extinguish flame, then turn on
hood to remove smoke and odor.
Cooktop: Smother fire or flame in a pan with a lid or
cookie sheet.
NEVER pick up or move a flaming pan.
Oven: Smother fire or flame by closing the oven door.
Do not use water on grease fires. Use baking soda, a
dry chemical or foam-type extinguisher to smother fire
or flame.
Child Safety
CAUTION
3
Use care when opening the oven door. Let hot air or
steam escape before removing or replacing food.
PREPARED FOOD WARNING: Follow food
manufacturer’s instructions. If a plastic frozen food
container and/or its cover distorts, warps, or is otherwise
damaged during cooking, immediately discard the food
and its container. The food could be contaminated.
Do not allow aluminum foil or meat probe to contact
heating element.
Always turn off all controls when cooking is completed.
Utensil Safety
Follow the manufacturer’s directions when using oven
cooking bags.
This appliance has been tested for safe performance
using conventional cookware. Do not use any devices
or accessories that are not specifically recommended in
this guide. Do not use add-on oven convection systems.
The use of devices or accessories that are not expressly
recommended in this guide can create serious safety
hazards, result in performance problems, and reduce the
life of the components of the appliance.
If pan is smaller than element, a portion of the element
will be exposed to direct contact and could ignite
clothing or potholder.
Only certain types of glass, glass/ceramic, ceramic,
earthenware, or other glazed utensils are suitable for
cooktop or oven service without breaking due to the
sudden change in temperature. Follow utensil
manufacturer’s instructions when using glass.
Turn pan handle toward center of cooktop, not out into
the room or over another surface element. This reduces
the risk of burns, ignition of flammable materials, or
spillage if pan is accidently bumped or reached by small
children.
Cooktop
NEVER leave surface units unattended, especially when
using high heat. An unattended boilover could cause
smoking and a greasy spillover can cause a fire.
This appliance is equipped with different size surface
elements. Select pans with flat bottoms large enough to
cover element. Fitting pan size to element will improve
cooking efficiency.
GLASS-CERAMIC SURFACE: NEVER cook on broken
cooktop. If cooktop should break, cleaning solutions and
spillovers may penetrate the broken cooktop and create
a risk of electric shock. Contact a qualified technician
immediately.
Deep Fat Fryers
Use extreme caution when moving the grease pan or
disposing of hot grease. Allow grease to cool before
attempting to move pan.
Ventilating Hoods
Clean range hood and filters frequently to prevent
grease or other flammable materials from accumulating
on hood or filter and to avoid grease fires.
When flaming foods under the hood, turn the fan on.
Cleaning Safety
Clean cooktop with caution. Turn off all controls and
wait for appliance parts to cool before touching or
cleaning. Use care to avoid steam burns if a wet sponge
or cloth is used to wipe spills on a hot surface. Some
cleaners can produce noxious fumes if applied to a hot
surface.
Clean only parts listed in this guide.
Self-Clean Oven
CAUTION
Before self-cleaning the oven, remove the oven racks,
broiler pan, food and any other utensils. Wipe
spillovers to prevent excessive smoke and flare-ups.
Do not clean door gasket. The door gasket is essential
for a good seal. Care should be taken not to rub,
damage, or move the gasket.
Do not use oven cleaners or oven liners of any kind in
or around any part of the self-clean oven.
8113P630-60 5/3/06, 8:59 AM4
4
Save These Instructions for Future Reference
Important Safety Notice
and Warning
The California Safe Drinking Water and Toxic
Enforcement Act of 1986 (Proposition 65) requires the
Governor of California to publish a list of substances
known to the State of California to cause cancer or
reproductive harm, and requires businesses to warn
customers of potential exposures to such substances.
Users of this appliance are hereby warned that when
the oven is engaged in the self-clean cycle, there may
be some low-level exposure to some of the listed
substances, including carbon monoxide. Exposure to
these substances can be minimized by properly venting
the oven to the outdoors by opening the windows and/
or door in the room where the appliance is located
during the self-clean cycle.
IMPORTANT NOTICE REGARDING PET BIRDS:
Never keep pet birds in the kitchen or in rooms where
the fumes from the kitchen could reach. Birds have a
very sensitive respiratory system. Fumes released during
an oven self-cleaning cycle may be harmful or fatal to
birds. Fumes released due to overheated cooking oil, fat,
margarine and overheated non-stick cookware may be
equally harmful.
Jenn-Air’s ventilation system is designed to capture both
cooking fumes and smoke from the cooktop surface. If
the system does not, here are some ducting installation
situations to check:
6” diameter round or 3
1
/
4
” x 10” rectangular ducting
should be used for duct lengths 10’-60’.
There should be a minimum clearance of 6” for
cooktop installed near a side wall.
If there is not an obvious improper installation, there
may be a concealed problem such as a pinched joint,
obstruction in the pipe, etc. Installation is
the responsibility of the installer and
questions should be addressed first by the
installer. The installer should very carefully
check the ducting installation instructions.
Use the Flow Tester Card provided with
your appliance to check the air flow.
DUCTING INFORMATION
5
CARE & CLEANING
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
Self-Clean Oven
CAUTION
It is normal for parts of the oven to become hot during a
self-clean cycle.
To prevent damage to oven door, do not attempt to open
the door when LOCK is displayed.
Avoid touching door, window or oven vent area during a
clean cycle.
Do not use commercial oven cleaners on the oven finish
or around any part of the oven. They will damage the
finish or parts.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior.
It is normal for flare-ups, smoking, or flaming to occur during
cleaning if the oven is heavily soiled. It is better to clean
the oven regularly rather than to wait until there is a heavy
build-up of soil in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Before Self-Cleaning
1. Turn off the oven light before cleaning. The oven light may
burn out during the clean cycle.
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks will discolor and may not slide
easily after a self-clean cycle if they are not removed.
Important: Remove the air grille from the cooking surface
before self-cleaning.
3. Clean oven frame, door frame, area outside of gasket, and
around the opening in the door gasket with a nonabrasive
cleaner such as Bon Ami* or detergent and water. The
self-cleaning process does not clean these areas. They
should be cleaned to prevent soil from baking on during
the clean cycle. (The gasket is the seal around the oven
door and window.)
4. To prevent damage, do not clean
or rub the gasket around the oven
door. The gasket is designed to
seal in heat during the clean cycle.
5. Wipe up excess grease or
spill-overs from the oven bottom.
This prevents excessive smoking,
flare-ups or flaming during the clean cycle.
6. Wipe up sugary and acidic spillovers such as sweet
potatoes, tomato, or milk-based sauces. Porcelain enamel
is acid-resistant, not acid-proof. The porcelain finish may
To set Self-Clean:
1. Press Clean pad.
2. REMOVE RACKS will be displayed. Remove the racks.
3. Select CONTINUE using the Quickset pad. The Quickset
pads are located on either side of the control panel
display.
4. Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Select MEDIUM soil
level using the Quickset pads.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. CLEAN, TIME, LOCKED and the cleaning time countdown
will be displayed while the oven is cleaning. OVEN
COOLING will appear in the display when the cleaning
time has been completed and the oven is still locked.
Important: The door lock will disengage approximately one
hour after the cleaning time is completed. OVEN COOLING
will go off in the display when the oven door has unlocked.
To Delay a Self-Clean Cycle:
1. Press Clean pad.
2. REMOVE RACKS will be displayed.
Remove the racks.
3. Select CONTINUE using the Quickset pad.
4. Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Select MEDIUM soil
level using the Quickset pads.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. The door will lock. CLEAN, TIME, LOCKED and the
cleaning time countdown will be displayed
6. After door locks, press the More Options pad.
7. Select DELAY using the Quickset pad.
8. Select the number of hours you want to delay the start of the
self-clean cycle.
9. The delay time and cleaning time will be displayed.
6
Notes:
If the oven door is left open, CLOSE DOOR will appear in
the display until the door is closed.
If more than 30 seconds elapse between pressing the
Clean pad and pressing a number pad, the program will
automatically return to the previous display.
The oven door will be damaged if it is forced to open
during cleaning or cooling process.
The first few times the oven is cleaned, some smoke and
odor may be detected. This is normal and will lessen or
disappear with use. If the oven is heavily soiled, or if the
broiler pan was accidently left in the oven, excessive
smoke and odor may occur.
As the oven heats and cools, you may hear sounds of
metal parts expanding and contracting. This is normal
and will not damage your appliance.
After Self-Cleaning
About one hour after the end of the clean cycle, the lock
will disengage and OVEN COOLING will go off in the
display. At this point, the door can be opened.
Some soil may leave a light gray, powdery ash which can be
removed with a damp cloth. If soil remains, it indicates that
the clean cycle was not long enough. The soil will be removed
during the next clean cycle.
If the oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and embossed rack
supports with a small amount of vegetable oil to restore ease
of movement.
A white discoloration may appear after cleaning if acidic or
sugary foods were not wiped up before the clean cycle. This is
normal and will NOT affect performance.
Cont.
PART PROCEDURE
CAUTION
Cleaning Procedures
Be sure appliance is off and all parts are cool before handling
or cleaning. This is to avoid damage and possible burns.
To prevent staining or discoloration, clean appliance after each use.
If a part is removed, be sure it is correctly replaced.
Access Panel The access panel is easily removed. To open panel, grasp sides and pull upward, lifting out.
To close panel, align catches with the studs on the range. Press the access panel
forward onto the studs and drop downward to engage.
Wash with soap and water, a glass cleaner, or mild liquid sprays.
Do not use excessive amounts of water.
To prevent scratching or dulling of the finish, do not use mildly abrasive, harsh or
caustic cleaners such as oven cleaners.
Important: To avoid the possibility of accidentally disconnecting any part of the
ventilation system, do not use the area behind the access panel for storage.
Control Panel To activate control lock for cleaning, see Locking the Control, page 18.
Wipe with damp cloth. Dry thoroughly.
Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on control pads and
display area.
Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel.
Control Knobs Remove knobs in the OFF position by pulling forward.
Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.
Turn on each element to be sure the knobs have been correctly replaced.
* Brand names are registered trademarks of the
respective manufacturers.
** To order call 1-800-JENNAIR (1-800-536-6247).
GREASE
CUP
STUDS
CATCHES
8113P630-60 5/3/06, 8:59 AM7
7
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
** To order direct, call 1-800-JENNAIR (1-800-536-6247).
PART PROCEDURE
Cooktop – Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia.
Glass-Ceramic Important: Call an authorized servicer if the glass-ceramic top should crack, break or if metal or
aluminum foil should melt on the cooktop.
Allow the cooktop to cool before cleaning.
General – Clean cooktop after each use, or when needed, with a damp paper towel and Cooktop Cleaning
Creme* (Part No. 20000001)**. Then buff with a clean, dry cloth.
Important: Permanent stains will develop if soil is allowed to cook on by repeatedly using the cooktop when soiled.
Heavy Soils or Metal Marks – Dampen a “scratchless” or “never scratch” scrubber sponge. Apply
Cooktop Cleaning Creme* and scrub to remove as much soil as possible. Apply a thin layer of the creme over
the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3 hours for very heavy soil). Keep
moist by covering the paper towel with plastic wrap. Scrub again, then buff with a clean, dry cloth.
Important: Only use a CLEAN, DAMP “scratchless” pad that is safe for non-stick cookware. The pattern and
glass will be damaged if the pad is not damp, if the pad is soiled, or if another type of pad is used.
Burned-On or Crusty Soils – Scrub with a “scratchless” or “never scratch” scouring pad and
Cooktop Cleaning Creme*.
Important: Hold a razor blade scraper at 30
°
angle and scrape any remaining soil. Then, clean as described
above. Do not use the razor blade for daily cleaning as it may wear the pattern on the glass.
Melted Sugar or Plastic – Immediately turn element to LOW and scrape sugar or plastic
from hot surface to a cool area. Then turn element OFF and allow to cool. Clean residue
with razor blade scraper and Cooktop Cleaning Creme*.
Oven Window Avoid using excessive amounts of water which may seep under or behind glass causing staining.
and Door - Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a
Glass cloth first.
Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will
scratch glass.
Oven Interior Follow instructions on pages 5-6 to set a self-clean cycle.
Oven Racks Clean with soapy water.
Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.
Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean operation.
If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease
of movement, then wipe off excess oil.
Stainless Steel DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.
(select models) DO NOT USE ABRASIVE OR ORANGE CLEANERS.
ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.
Daily Cleaning/Light Soil –– Wipe with one of the following - soapy water, white vinegar/water solution,
Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse
and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.
20000008)**.
Moderate/Heavy Soil –– Wipe with one of the following - Bon Ami, Smart Cleanser, or Soft Scrub* -
using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi-
purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks,
follow with Stainless Steel Magic Spray*.
Discoloration –– Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse
immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.
8113P630-60 5/3/06, 8:59 AM8
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
** To order direct, call 1-800-JENNAIR (1-800-536-6247).
PART PROCEDURE
Grill
Accessories:
Basin and The basin pan and basin are located under the grill element and/or cartridges. Clean after each use of the grill.
Basin Pan – To remove light soil, clean with soapy water or spray with cleansers such as Fantastik* or Formula 409*. For
Porcelain easier cleanup: a) spray with a household cleanser; b) cover with paper towels; c) add small amount of hot
water to keep the paper towels moist; d) cover and wait 15 minutes; and e) wipe clean.
To remove moderate soil, scrub with Bon Ami*, a soft scrub cleanser or plastic scrubber.
Basin liner pan can be cleaned in the dishwasher.
Important: Check the grease drain after each use of the grill. To clean, pour about
1
/
3
cup of very hot tap
water mixed with 1 teaspoon dish detergent down the drain.
Element Never immerse in water. Most soil will burn off during use. The terminal block may be wiped with warm,
soapy water. Do not use abrasive cleaners or materials. Dry thoroughly before reinserting in the cooktop.
Grates – Cast Wash cool grates (DO NOT IMMERSE HOT GRILL GRATES IN WATER) with detergent in hot water in the
aluminum sink or wash them in the dishwasher. Be sure to remove all food residue before cooking on the grill
coated with grates again.
non-stick Remove stubborn soils with a plastic mesh puff or pad. Use only those cleaning products which state
finish they are recommended for use when cleaning nonstick surfaces.
If grates were washed in the dishwasher, season with oil prior to grilling.
Do not use metal brushes or abrasive scouring pads or other scrubbers intended to clean outdoor charcoal
grills. These will remove the finish as well as scratch the grates. Do not clean in self-cleaning oven or use
oven cleaners on the grates.
Grease Cup The container is located on the left side behind the bottom access panel, underneath
the range. (See page 6 for opening access panel.) It collects grease and other
liquids created while grilling or using some of the accessories. Check each time after
grilling and empty when grease is noticeable. To remove, simply grasp the handle,
and pull from the bracket holding the container.
The container can be washed in hot, soapy water or in the dishwasher.
8
MAINTENANCE
CAUTION
Oven Door
NEVER place excessive weight on or stand on an open
oven door. This could cause the range to tip over, break
the door, or injure the user.
NEVER attempt to open or close door or operate oven until
door is properly replaced.
NEVER place fingers between hinge and front oven frame.
Hinge arms are spring mounted. If accidentally hit, the
hinge will slam shut against oven frame and could injure
your fingers.
To remove:
1. When cool, open the oven door to the broil stop position
(opened about four inches).
2. Grasp door at each side. Do not
use the door handle to lift door.
3. Lift up evenly until door clears
hinge arms.
To replace:
1. Grasp door at each side.
2. Align slots in the door with the hinge arms on the range.
3. Slide the door down onto the hinge arms until the door is
completely seated on the hinges. Push down on the top
corners of the door to completely seat door on hinges.
Door should not appear crooked.
Important: The oven door on a new range may feel “spongy”
when it is closed. This is normal and will decrease with use.
Cont.
8113P630-60 5/3/06, 8:59 AM9
9
Oven Window
Leveling Legs
ANTI-TIP BRACKET
LEVELING LEG
Be sure the anti-tip bracket secures one of the rear
leveling legs to the floor. This bracket prevents the range
from accidentally tipping.
Be sure the range is leveled when installed. If
the range is not level, turn the leveling legs,
located at each corner of the range, until range
is level.
ANTI-TIP BRACKET
LEVELING LEG
CAUTION
To assure the proper replacement bulb is used, order bulb
from Jenn-Air. Call 1-800-JENNAIR (1-800-536-6247), ask for
part number 74004458 - halogen bulb.
To Replace Oven Light Bulb:
1. Disconnect power to the appliance.
2. When oven is cool, use fingertips to grasp edge of bulb
cover. Pull out and remove.
3. Carefully remove old bulb by pulling straight out of
ceramic base.
4. To avoid damaging or decreasing the life of the new bulb,
do not touch the bulb with bare hands or fingers. Hold
with a dry cloth or paper towel. Push new bulb prongs
straight into small holes of ceramic base.
5. Replace bulb cover by snapping into place.
6. Reconnect power to the oven. Reset clock.
Oven Light
CAUTION
10
TROUBLESHOOTING
For most concerns, try these first. Check if oven controls have been properly set.
Check to be sure plug is securely inserted into receptacle.
Check or re-set circuit breaker. Check or replace fuse.
Check power supply.
Part or all of appliance does Check if surface and/or oven controls have been properly set. See pgs. 12 & 19.
not work. Check if oven door is unlocked after self-clean cycle. See pg. 5.
Check if oven is set for a delayed cook or clean program. See pgs. 19 & 5.
Check if Control Lock is activated. See pg. 18.
Check if control is in Sabbath Mode. See pg. 31.
Clock, indicator words, and/or Oven may be set for a Cook & Hold or delay function.
lights operate but oven does Control Lock may have been set. See pg. 18.
not heat.
Baking results are not as Make sure the oven vent has not been blocked. See pg. 23 for location.
expected or differ from Check to make sure range is level.
previous oven. Temperatures often vary between a new oven and an old one. As ovens age, the oven
temperature often “drifts” and may become hotter or cooler. See pg. 31 for
instructions on adjusting the oven temperature. Important: It is not recommended
to adjust the temperature if only one or two recipes are in question.
Food is not broiling properly or Check oven rack positions. Food may be too close to element.
smokes excessively. Broil element was not preheated.
Aluminum foil was incorrectly used. Never line the broiler insert with foil.
Oven door was closed during broiling. Leave the door open to the first stop position
(about 4 inches).
Trim excess fat from meat before broiling.
A soiled broiler pan was used.
Voltage in house may be low.
Oven will not self-clean. Check to make sure the cycle is not set for a delayed start. See pg. 5.
Check if door is closed.
Check if control is in Sabbath Mode. See pg. 31.
Oven may be over 400° F. Oven temperature must be below 400° F to program a
clean cycle.
Oven did not clean properly. Longer cleaning time may be needed.
Excessive spillovers, especially sugary and/or acidic foods, were not removed prior
to the self-clean cycle.
Oven door will not unlock after Oven interior is still hot. Allow about one hour for the oven to cool after the
self-clean cycle. completion of a self-clean cycle. The door can be opened when the LOCK indicator
word is not displayed.
The control and door may be locked. See pg. 18.
There are no beeps and Oven may be in Sabbath Mode. See pg. 31.
no display.
PROBLEM SOLUTION
Cont.
8113P630-60 5/3/06, 8:59 AM11
11
Smoothtop surface 1.Tiny scratches or abrasions.
shows wear. Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans
across top. Make sure pan bottom is not rough. Use the recommended cleaning
agents. See page 7.
2.Metal marks.
Do not slide metal pans across top. When cool, clean with Cooktop Cleaning Creme.
See page 7.
3.Brown streaks and specks.
Remove spills promptly. Never wipe with a soiled cloth or sponge. Make sure cooktop
and pan bottom are clean.
4.Areas with a metallic sheen.
Mineral deposits from water and food. Use recommended cleaning agents. See page 7.
5.Pitting or flaking.
Remove sugary boilovers promptly. See page 7.
Moisture collects on oven This is normal when cooking foods high in moisture.
window or steam comes from Excessive moisture was used when cleaning the window.
oven vent.
There is a strong odor or light This is normal for a new range and will disappear after a few uses. Initiating a clean
smoke when oven is turned on. cycle will “burn off” the odors more quickly.
Turning on a ventilation fan will help remove the smoke and/or odor.
Excessive food soils on the oven bottom. Use a self-clean cycle.
Grill heating element or Surface controls may not be set properly.
cooktop does not get Voltage to house may be low.
hot enough.
Ventilation system is not Check on cross ventilation in room or make up air.
capturing smoke efficiently. Excessive amount of smoke is being created; check instructions for grilling, trimming
meats. See pg. 14.
Outside wall cap may be trapped shut.
Range may be improperly installed; check ducting information. See pg. 4.
Air filter may be improperly installed. See pg. 15.
Fault Codes The oven may detect a fault during programming or during operation. If a fault is
detected, the message FAULT DETECTED - PRESS POWER TO CLEAR or FAULT
DETECTED - PRESS ENTER TO TRY AGAIN may appear. Follow directions in the display.
If the fault reappears or does not clear, call an authorized servicer or the toll-free number
in the display.
If the same operation is attempted before having the wall oven repaired, the message
FEATURE NOT AVAILABLE will appear. The feature will remain inoperable until service
is obtained.
If the oven is heavily soiled, excessive flareups may result in a fault code during cleaning.
Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then
reset the clean cycle. If the fault code reappears, contact an authorized servicer.
Noises may be heard. The oven makes several low-level noises. You may hear the oven relays as they go on
and off. This is normal.
As the oven heats and cools, you may hear sounds of metal parts expanding and
contracting. This is normal and will not damage your appliance.
SAb flashing and then Oven is in Sabbath Mode. To cancel, press and hold the Setup pad for five
displayed continuously. seconds.
PROBLEM SOLUTION
8113P630-60 5/3/06, 8:59 AM12
12
SURFACE COOKING
Surface Controls
Use to turn on the surface elements. An infinite choice of
heat settings is available from Low to High. The knobs can
be set on or between any of the settings.
Medium (5): Use to
maintain slow boil for
large amounts of liquids
and for most frying
operations.
BEFORE COOKING
Always place a pan on the surface unit before you turn it
on. To prevent damage to range, never operate surface
unit without a pan in place.
NEVER use the cooktop as a storage area for food or
cookware.
DURING COOKING
Be sure you know which knob controls which surface
unit. Make sure you turned on the correct surface unit.
Begin cooking on a higher heat setting then reduce to a
lower setting to complete the operation. Never use a
high heat setting for extended cooking.
NEVER allow a pan to boil dry. This could damage the
pan and the appliance.
NEVER touch cooktop until it has cooled. Expect some
parts of the cooktop, especially around the surface units,
to become warm or hot during cooking. Use potholders
to protect hands.
CAUTION
Suggested Heat Settings
The size, type of cookware and cooking operation will affect
the heat setting.
AFTER COOKING
Make sure surface unit is turned off.
Clean up messy spills as soon as possible.
OTHER TIPS
If cabinet storage is provided directly above cooking
surface, limit it to items that are infrequently used and
can be safely stored in an area subjected to heat.
Temperatures may be unsafe for items such as volatile
liquids, cleaners or aerosol sprays.
NEVER leave any items, especially plastic items, on the
cooktop. The hot air from the vent may ignite flammable
items, melt or soften plastics, or increase pressure in
closed containers, causing them to burst.
NEVER allow aluminum foil, meat probes or any other
metal object, other than a pan on a surface element, to
contact heating elements.
NEVER store heavy items above the cooktop that could fall
and damage it.
Low (1): Use to keep foods
warm and melt chocolate
and butter.
High (9): Use to bring
liquid to a boil. Always
reduce setting to a lower
heat when liquids begin to
boil or foods begin to cook.
Med. Low (3):
Use to
continue
cooking
covered foods
or steam foods.
Med. High (7): Use to
brown meat, heat oil for
deep fat frying or
sauteing. Maintain fast
boil for large amounts
of liquids.
Setting the Controls
1. Place pan on surface element.
2. Push in and turn the knob in either direction to the desired
heat setting.
The control panel is marked to identify which
element the knob controls. For example, the
graphic at right indicates right front element.
3. There is an element indicator light on the control panel.
When any surface control knob is turned on, the light will
turn on. The light will turn off when all the surface
elements are turned off.
When a control is turned on, a glow can be seen through
the smoothtop surface. The element will cycle on and off
to maintain the preset heat setting, even on High.
4. After cooking, turn knob to OFF. Remove pan.
Setting the controls for grilling:
Knob A - Exhaust fan only. Knob will not operate the grill
element.
Knob B - Exhaust fan and grill element.
Setting the controls for cartridges:
Knob A - Left front element.
Knob B - Left rear element.
A B
8113P630-60 5/3/06, 8:59 AM13
13
Cooktop cartridges, either conventional coil or radiant
element, can be installed on either side of the range. (See
page 33 for all available cartridges and accessories, and their
model numbers.)
To Install Cartridges:
1. If the grill grates, element, and/or basin pan are in place,
remove before installing a cooktop cartridge. Clean
porcelain basin of any grease accumulation. (See page 8
for cleaning recommendations.)
2. To install any of the optional cooktop cartridges, be sure
controls are turned off and the cartridge is cool. Position
the cartridge terminal plug toward the terminal receptacle.
This receptacle is located at the front of the left side and at
the back of the right side of the range.
3. Slide the cartridge toward the receptacle until the
cartridge terminal plug is completely engaged.
4. Lower the opposite end of the cartridge into the rangetop
until it is flush with the surface. Your range is now ready
to use.
To Remove Cartridges:
1. Controls must be off and the cartridge should be cool.
2. Lift up the edge of the cartridge until top of cartridge
clears the opening on the range by about 2 inches.
Important: Lifting the cartridge too high while still
engaged in the receptacle could damage the terminal
plug.
3. To disengage terminal, hold cartridge by the sides and pull
away from the terminal receptacle. Lift out when fully
unplugged.
4. Do not stack cartridges where they may fall or be
damaged. Never store other materials on top of the glass-
ceramic cartridges since this could damage or scratch the
surface.
Home Canning
Canning should be done on the conventional coil cartridge
only. Canning element accessory, Model A145A, makes it
possible to use large oversized canners with the conventional
coil cartridge.
For additional information, refer to the Use and Care Guide
packaged with your cartridge.
14
Using the Grill
Grilling Tips
Be sure to follow directions for using the grill.
Suggested cooking times and control settings (see page
15) are approximate due to variations in the foods and
electrical voltage.
For best results, buy top grade meat. Meat that is at least
3
/
4
inch will grill better than thinner cuts.
Score fat on edges of steak, but do not cut into meat, to
prevent curling while cooking.
For the attractive “branded” look on steaks, be sure grill is
preheated. Allow one side of meat to cook to desired
doneness, or until juices appear on the top surface, before
turning. Turn steaks and hamburgers just once.
Manipulating food causes loss of juices.
When basting meats or applying sauces to foods,
remember that excessive amounts accumulate inside your
grill and do not improve the food flavor.
Apply sauces during the last 15 to 20 minutes of cooking
time unless recipe specifies otherwise. Plus, anytime a
sugar-based marinade (for example barbecue sauce) is
going to be used, the grates should be “seasoned” prior to
preheating. (See Using the Grill section.)
There are many meat marinades which will help tenderize
less expensive cuts of meat for cooking on the grill.
Certain foods, such as poultry and non-oily fish, may need
some extra fat. Brush with oil or melted butter occasionally
while grilling.
Use tongs with long handles or spatulas for turning meats.
Do not use forks as these pierce the meat, allowing juices
to be lost.
Before the first use, wash your new grill grates in hot
soapy water, rinse and dry. Then “season” the surface by
wiping on a thin coating of cooking oil. Remove excess oil
by wiping with paper towel.
This procedure should be repeated when either:
a)cleaning in the dishwasher since the detergent may
remove seasoning or
b)anytime a sugar-based marinade (for example,
barbecue sauce) is going to be used.
Preheat the grill on High for 5 minutes. Preheating
improves the flavor and appearance of meats and quickly
sears the meat to help retain the juices.
Use nonmetallic spatulas or utensils to prevent damaging
the nonstick grill grate finish.
Excessive amounts of fat should be trimmed from meats.
Only a normal amount is necessary to produce the smoke
needed for that smoked, “outdoor” flavor. Excessive fat can
create cleaning and flare-up problems.
Allowing excessive amounts of grease or drippings to
constantly flare-up voids the warranty on the grill grates.
Excessive flare-ups indicate that either the grill interior
needs to be cleaned, that excessive amounts of fat are in
the meat or the meat was not properly trimmed.
Grease drippings will occasionally ignite to produce
harmless puffs of flame for a second or two. This is a
normal part of the cooking process. Important: For
information on the grease cup, see page 8.
NEVER LEAVE GRILL UNATTENDED DURING
GRILL OPERATION.
Should excess grease cause sustained flare-ups:
1. Turn on the fan manually.
2. Immediately turn grill controls to OFF.
3. Remove meat from grill.
Notes:
Do not use aluminum foil inside the grill
area.
Do not use charcoal or wood chips in
the grill area.
Do not allow grill basin pan to
become overloaded with grease.
Clean frequently.
Do not cover grates completely with meat. Leave air
space between each steak, etc. to allow proper
ventilation as well as prevent flare-ups.
Ventilation System
The built-in ventilation system removes cooking vapors, odors
and smoke from foods prepared on your cooktop and grill.
To operate the ventilation
system manually, push the
Vent Fan pad located on the
electronic control. Push once
for Low, push again for High
and a third time to turn the
fan Off.
The ventilation system will operate automatically when the
grill element is in use.
The fan can be used to remove strong odors from the
kitchen, as when chopping onions near the fan.
Cont.
8113P630-60 5/3/06, 8:59 AM15
15
Care and Cleaning of the
Ventilation System
Air Grille: The air grille lifts off easily. Wipe clean or wash in
dishwasher or sink with mild household detergents. To
prevent scratching the surface, do not use abrasive
cleaners or scrubbing pads.
Filter: Turn off ventilation system before removing. The filter
is a permanent type and should be cleaned when soiled.
Clean in sink with warm water and detergent or in
dishwasher.
IMPORTANT: DO NOT OPERATE SYSTEM WITHOUT
FILTER. Filter should always be placed at an angle. As you
face the front of the range, the top of the filter should rest
against the left side of the vent opening. The bottom should
rest against the right side of the vent chamber at the
bottom. Important: If filter is flat against the fan wall,
ventilation effectiveness is reduced.
AIR FILTER
Ventilation Chamber: This area, which houses the filter,
should be cleaned in the event of spills or whenever it
becomes coated with a film of grease. It can be cleaned with
paper towel, damp cloth, or sponge and mild household
detergent or cleanser.
Important: The oven vent is located under the right side of
the air grille. When using or cleaning the oven, hot and
moist air may be noticed in this area. The area near the vent
may become hot enough to cause burns. Be careful not to
spill anything into this vent. The air grille must be
removed before the self-clean cycle.
Preheat grill on High 5 minutes, for best flavor.
FOODS SETTING COOKING TIME PROCEDURE
Steak: (1 - 1
1
/
4
”) Rare High 10 to 17 minutes Turn after 8 to 10 minutes.
Medium High 20 to 25 minutes Turn after 13 to 15 minutes.
Well High 25 to 32 minutes Turn after 15 to 17 minutes.
Hamburgers: (3-4 oz.) 9 15 to 25 minutes Turn after half the time.
Pork Chops: (
1
/
2
-
3
/
4
”) 9 25 to 40 minutes Turn occasionally.
Ham Slices: (
1
/
2
”) High 10 to 15 minutes Turn once.
Fully-cooked Sausages: Hot Dogs High 5 to 15 minutes Turn occasionally.
Polish High 10 to 20 minutes Turn once.
Fresh Sausage: Links & Patties 9 15 to 20 minutes Turn occasionally.
Chicken: Boneless Breasts 9 25 to 35 minutes Turn occasionally.
Bone-in Breasts, Drumsticks 9 45 to 60 minutes Turn occasionally. Brush with marinade
and Thighs or glaze during last 10 minutes.
Fish: Steaks (1”) 9 20 to 30 minutes Brush with butter. Turn after half the time.
Shrimp: (Skewered) 9 8 to 12 minutes Turn and brush with butter or marinade
frequently.
Garlic Bread, Bruschetta High 2 to 4 minutes Turn after half the time.
Hot Dog Buns, Hamburger Buns 9 2 to 3 minutes
Fruits & Vegetables: Pineapple Rings High 8 to 10 minutes Turn after half the time.
Pepper Rings High 7 to 9 minutes Brush with oil. Turn after half the time.
(
1
/
2
” Rings) High 8 to 12 minutes Brush with butter. Turn occasionally.
(
1
/
2
” Lengthwise
Slices)
Grill Guide
Important: This chart is a suggested guide. Cooking times and control settings are approximate due to variations in meats,
control switches, and voltage.
8113P630-60 5/3/06, 8:59 AM16
16
Canning and Oversize Cookware
All canners and large pots must have flat bottoms and
must be made from heavy-gauge materials. This is critical
on smoothtop surfaces. The base must not be more than
1 inch larger than the element.
When canners and pots do not meet these standards, cooking
times may be longer, and cooktops may be damaged.
Some canners are designed with smaller bases for use on
smoothtop surfaces.
When canning, use the High heat setting only until the
water comes to a boil or pressure is reached in the canner.
Reduce to the lowest heat setting that maintains the boil or
pressure. If the heat is not turned down, the cooktop may be
damaged.
Tips to Protect the
Smoothtop Cartridge Surface
Cleaning (see page 7 for more information)
Before first use, clean the cooktop.
Clean your cooktop daily or after each use. This will keep your
cooktop looking good and can prevent damage.
If a spillover occurs while cooking, immediately clean the spill
from the cooking area while it is hot to prevent a tough
cleaning chore later. Using extreme care, wipe spill with a
clean, dry towel.
Do not allow spills to remain on the cooking area or the
cooktop trim for a long period of time.
Never use abrasive cleansing powders or scouring pads
which will scratch the cooktop.
Never use chlorine bleach, ammonia or other cleansers not
specifically recommended for use on glass-ceramic.
To Prevent Marks & Scratches
Do not use glass pans. They may scratch the surface.
Never place a trivet or wok ring between the surface and pan.
These items can mark or etch the top.
Do not slide aluminum pans across a hot surface. The pans
may leave marks which need to be removed promptly. (See
Cleaning, page 7.)
Make sure the surface and the pan bottom are clean before
turning on to prevent scratches.
To prevent scratching or damage to the glass-ceramic top, do
not leave sugar, salt or fats on the cooking area. Wipe the
cooktop surface with a clean cloth or paper towel before
using.
Never slide heavy metal pans across the surface since these
may scratch.
To Prevent Stains
Never use a soiled dish cloth or sponge to clean the cooktop
surface. A film will remain which may cause stains on the
cooking surface after the area is heated.
Continuously cooking on a soiled surface may/will result in a
permanent stain.
To Prevent Other Damage
Do not allow plastic, sugar or foods with high sugar content
to melt onto the hot cooktop. Should this happen, clean
immediately. (See Cleaning, page 7.)
Never let a pan boil dry as this will damage the surface and
pan.
Never use cooktop as a work surface or cutting board.
Never cook food directly on the surface.
Do not use a small pan on a large element. Not only does this
waste energy, but it can also result in spillovers burning onto
the cooking area, which requires extra cleaning.
Cookware Recommendations
Do not use non-flat specialty items that are oversized or
uneven such as round bottom woks, rippled bottom and/or
oversized canners and griddles.
Do not use foil or foil-type containers. Foil may melt onto the
glass. If metal melts on the cooktop, do not use. Call an
authorized Jenn-Air Servicer.
Select Avoid
Flat, smooth-bottom Pans with grooved or warped bottoms.
pans. Pans with uneven bottoms do not cook
efficiently and sometimes may not
boil liquid.
Heavy-gauge pans. Very thin-gauge metal or glass pans.
Pans that are the Pans smaller or larger than the
same size as the element by 1 inch.
element.
Secure handles. Cookware with loose or broken handles.
Heavy handles that tilt the pan.
Tight-fitting lids. Loose-fitting lids.
Flat bottom woks. Woks with a ring-stand bottom.
Using the right cookware can prevent many problems, such as
food taking longer to cook or achieving inconsistent results.
Proper pans will reduce cooking times, use less energy, and
cook food more evenly.
Flat Pan Tests
The Ruler Test:
1. Place a ruler across the bottom of the pan.
2. Hold it up to the light.
3. Little or no light should be visible under the ruler.
The Bubble Test:
1. Put 1 inch of water in the pan. Place on cooktop and turn
control to High.
2. Watch the formation of the bubbles as the water heats.
Uniform bubbles mean good performance, and uneven
bubbles indicate hot spots and uneven cooking.
8113P630-60 5/3/06, 8:59 AM17
17
OVEN COOKING
A Rapid Preheat Use to decrease preheating time.
B Convect Use for convection baking and roasting.
C Bake Use for baking and roasting.
D Broil Use for broiling and top browning.
E TIMER 1 Sets timer.
F Display Displays oven functions, options and
window time of day.
G TIMER 2 Sets timer.
H Number Pads Use to enter time and temperature,
or to enter Favorites names.
I Favorites Use to access, program or save
baking cycles.
J More Options Use to access additional features.
K Clean Use to set self-clean cycle.
L Setup Use to view or change factory
default settings.
M Vent Fan Activates the ventilation fan on
the cooktop.
N Oven Light Use to turn the oven light on or off.
O CANCEL Cancels all operations except Timer,
Clock, Favorites, Setup and Vent Fan.
P Quickset pads Use to select options in display
window (next to display window
on both sides).
The control panel is designed for ease in programming. The display window shows options for each function and moves from step
to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake
operation.
A B C D E F G H
Control Panel
Quickset Pads
Quickset pads are located on each side of the display window
and are used to select the desired function or option in the
display window. To select the option or function, press the
Quickset pad next to the word.
Important: Four seconds after entering the function,
option, number or letter, the function will automatically be
entered. If more than 30 seconds elapse between steps in
programming, the function will be canceled and the
display will return to the previous display.
Clock
Setting the Clock:
1. Press the Setup pad.
2. Select CLOCK using the Quickset pads.
3. Select TIME.
4. Enter the time using the number pads.
5. Press Enter pad.
6. Select AM or PM in 12 hour mode. (For 24 hour clock, see
page 18.)
7. To exit the Setup mode, press Setup pad.
If you need to back out of a function or option in the display,
press the Back pad. When your programming is complete,
press the Enter pad or wait four seconds and the function will
start automatically.
Up arrows indicate additional screens with additional options.
Press the Quickset pads next to the arrows to scroll through
the display.
I J K L M N O P
8113P630-60 5/3/06, 8:59 AM18
18
Activating and canceling the clock/day
of week display:
1. Press Setup pad.
2. Select CLOCK.
3. Press the arrow to scroll until DISABLE is displayed.
4. Select DISABLE.
5. Select OFF to turn the clock display off, or select ON to turn
the clock display on.
6. Select OFF to turn the day of the week display off. Select
ON to turn the weekday display on.
7. To exit the Setup mode, press Setup pad.
Entering the day of the week:
1. Press Setup pad.
2. Select CLOCK.
3. Press the arrow to scroll until DAY is displayed.
4. Use Quickset arrow to scroll through the days.
5. To exit the Setup mode, press Setup pad.
To set the clock for a 12 or 24 hour format:
The clock can be set to display time in either a 12 hour or 24
hour format.
1. Press the Setup pad.
2. Select CLOCK.
3. Use the arrow to scroll to the next screen.
4. Select 12/24 HOUR.
5. Select 12 HR or 24 HR.
6. To exit Setup mode, press Setup pad.
Timers
Setting the Timers (Timer 1 or Timer 2):
1. Press TIMER 1 or TIMER 2 pad.
2. Press one of the displayed times using the
Quickset pads, or press the number pads to
enter the desired time.
Important: Each press of the displayed time choices adds
additional time. For example, pressing “10 MIN” three
times provides 30 minutes on the timer (0:30).
3. Press Enter pad.
Changing the amount of time entered once the
Timer starts:
1. Press the TIMER 1 or TIMER 2 pad once.
2. Press the displayed times on the Quickset
pads until the desired time is entered.
OR
3. Press the number pads to enter the new desired time.
4. Press Enter pad.
Canceling the Timer:
Press the TIMER 1 or TIMER 2 pad twice.
If both Timers are active:
If the desired Timer is already in the foreground, press once
for edit mode and twice to cancel the Timer. If the desired
Timer is not in the foreground, follow the steps below.
1. Press the desired TIMER pad once. The selected Timer will
come to the foreground.
2. Press the TIMER pad a second time to access the edit
mode in order to make changes.
3. Pressing the TIMER pad a third time will cancel the Timer.
Changing the Timer beeps:
The signal beeps for TIMER 1 and TIMER 2 can be changed.
The options available are two beeps every thirty seconds, two
beeps every sixty seconds or one beep only. The default
setting is one beep.
1. Press the Setup pad.
2. Select the arrow to scroll until TONES
is displayed.
3. Select TONES.
4. Select TIMERS TONES.
5. Select the desired timer beep format (2-30 SEC, 2-60 SEC
or 1 BEEP).
6. Press Setup pad to exit Setup mode.
Locking the Control and Oven Door
The oven control and oven door can be locked to prevent
accidental programming. If an oven function is currently
being used, the control and door cannot be locked.
To lock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds or until CONTROL LOCKED appears in the
display.
To unlock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds. UNLOCKING DOOR will appear in the display
when the control and door are unlocking.
8113P630-60 5/3/06, 8:59 AM19
19
Notes:
If more than thirty seconds elapse between pressing a
pad and pressing a number pad, the display will return
to the previous display.
Whenever the temperature appears in the display, the
oven is heating.
To change the oven temperature during cooking, press
the Bake pad and select a displayed temperature or use
the number pads to enter the desired temperature.
The oven will automatically shut off after 12 hours if it is
accidentally left on. To set a Sabbath Mode, see Sabbath
Mode, page 31.
time. When that time has elapsed, the oven will automatically
reduce temperature to 170° F and keep the food warm for up
to an hour and then automatically turn off.
When using Delay, the oven begins to cook later in the day.
Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time. When that time has elapsed, the oven will keep the food
warm for up to an hour then automatically turn off.
To set Cook & Hold (select models):
The temperature in the display will increase in 1°
increments until the oven reaches the preset
temperature. Allow about 15 minutes for the oven
to preheat.
When the oven is preheated, the oven will beep and
PREHEAT will no longer be displayed.
3. At the end of cooking, turn the oven off by
pressing the CANCEL pad. Remove food
from the oven. The oven will continue
operating until the CANCEL pad is pressed.
Baking
To set Bake:
1. Press the Bake pad.
2. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
The temperature can be set from 170° F to 550° F
in 5° increments.
After three seconds, the oven will begin to preheat.
BAKE and PREHEAT will appear in the display along
with 100° or the actual oven temperature, whichever
is higher.
To set a Delay:
1. After Bake has been programmed, press
the More Options pad.
2. Select DELAY.
3. Select the amount of time you want to delay the start of
cooking using the displayed times or the number pads.
4. Select the amount of time you want to cook using the
displayed times or the number pads.
5. The display will show BAKE, the temperature, the delay
time and the cook time countdown.
6. When the delay time has expired, the oven will begin
heating. COOK TIME, the cook time countdown, PREHEAT,
BAKE and the actual oven temperature will be displayed.
CAUTION
Do not use delayed baking for highly perishable foods such
as dairy products, pork, poultry or seafood.
Bake Options
Cook & Hold (select models) and Delay options are available
when baking. When using the Cook & Hold option (select
models), the oven begins to heat immediately after the control
has been set. Then, the oven cooks for a specified length of
1. After Bake has been programmed, press
the More Options pad.
2. Select COOK/HLD.
3. Select the amount of time you want to bake by pressing
the Quickset pads or the number pads.
4. Press Enter pad.
5. COOK TIME, the cook time countdown, PREHEAT, BAKE
and the actual temperature will be displayed.
The oven will cook for the selected time, then keep food warm
for one hour.
8113P630-60 5/3/06, 8:59 AM20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108

Jenn-Air Range ELECTRIC DOWNDRAFT SLIDE-IN RANGE Manuel utilisateur

Catégorie
Cuisinières
Taper
Manuel utilisateur