Jenn-Air Range ELECTRIC DOWNDRAFT SLIDE-IN RANGE Manuel utilisateur

JENN-AIR

®

ELECTRIC DOWNDRAFT

SLIDE-IN RANGE

Important Safety Instructions.....................................1-4

Ducting Information...........................................................4

Care & Cleaning..............................................................5-8

Maintenance.....................................................................8-9

Troubleshooting .........................................................10-11

Surface Cooking.........................................................12-16

Oven Cooking..............................................................17-23

Options ..........................................................................24-28

Favorites...............................................................................29

Setup ..............................................................................30-32

Cartridges & Accessories ..............................................33

Warranty & Service...........................................................35

Guide d’utilisation et d’entretien.................................36

Guía de uso y cuidado....................................................72

USE & CARE

GUIDE

TABLE OF CONTENTS

®

8113P630-60 5/3/06, 8:59 AM1

1

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this guide for future

reference. Keep sales receipt and/or cancelled check as

proof of purchase.

Model Number__________________________________

Serial Number __________________________________

Date of Purchase ________________________________

If you have questions, call:

Jenn-Air Customer Assistance

1-800-JENNAIR (1-800-536-6247)

1-800-688-2080 (U.S. TTY for hearing or speech impaired)

(Mon.-Fri., 8 am-8 pm Eastern Time)

Internet: http://www.jennair.com

In our continuing effort to improve the quality and

performance of our cooking products, it may be necessary

to make changes to the appliance without revising this

guide.

For service information, see page 35.

IMPORTANT SAFETY

INSTRUCTIONS

Warning and Important Safety Instructions appearing

in this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution, and care must be exercised when

installing, maintaining, or operating the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION – Hazards or unsafe practices which

COULD result in minor personal injury.

WARNING

CAUTION

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service,

or replace any part of your appliance unless it is

specifically recommended in this guide. All other

servicing should be referred to a qualified servicer.

Always disconnect power to appliance before servicing.

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

To Prevent Fire or Smoke

Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials. Flammable materials should not

be stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot.

To prevent grease fires, do not let cooking grease or

other flammable materials accumulate in or near the

appliance.

General Instructions

WARNING: To reduce risk of

tipping of the appliance from

abnormal usage or by excessive loading of the

oven door, the appliance must be secured by a

properly installed anti-tip device.

WARNING

• ALL RANGES CAN TIP AND

CAUSE INJURIES TO PERSONS

• INSTALL ANTI-TIP DEVICE

PACKED WITH RANGE

• FOLLOW ALL INSTALLATION

INSTRUCTIONS

8113P630-60 5/3/06, 8:59 AM2

2

In Case of Fire

Turn off appliance and ventilating hood to avoid

spreading the flame. Extinguish flame, then turn on

hood to remove smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

• Oven: Smother fire or flame by closing the oven door.

Do not use water on grease fires. Use baking soda, a

dry chemical or foam-type extinguisher to smother fire

or flame.

Child Safety

CAUTION

3

Use care when opening the oven door. Let hot air or

steam escape before removing or replacing food.

PREPARED FOOD WARNING: Follow food

manufacturer’s instructions. If a plastic frozen food

container and/or its cover distorts, warps, or is otherwise

damaged during cooking, immediately discard the food

and its container. The food could be contaminated.

Do not allow aluminum foil or meat probe to contact

heating element.

Always turn off all controls when cooking is completed.

Utensil Safety

Follow the manufacturer’s directions when using oven

cooking bags.

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices

or accessories that are not specifically recommended in

this guide. Do not use add-on oven convection systems.

The use of devices or accessories that are not expressly

recommended in this guide can create serious safety

hazards, result in performance problems, and reduce the

life of the components of the appliance.

If pan is smaller than element, a portion of the element

will be exposed to direct contact and could ignite

clothing or potholder.

Only certain types of glass, glass/ceramic, ceramic,

earthenware, or other glazed utensils are suitable for

cooktop or oven service without breaking due to the

sudden change in temperature. Follow utensil

manufacturer’s instructions when using glass.

Turn pan handle toward center of cooktop, not out into

the room or over another surface element. This reduces

the risk of burns, ignition of flammable materials, or

spillage if pan is accidently bumped or reached by small

children.

Cooktop

NEVER leave surface units unattended, especially when

using high heat. An unattended boilover could cause

smoking and a greasy spillover can cause a fire.

This appliance is equipped with different size surface

elements. Select pans with flat bottoms large enough to

cover element. Fitting pan size to element will improve

cooking efficiency.

GLASS-CERAMIC SURFACE: NEVER cook on broken

cooktop. If cooktop should break, cleaning solutions and

spillovers may penetrate the broken cooktop and create

a risk of electric shock. Contact a qualified technician

immediately.

Deep Fat Fryers

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before

attempting to move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent

grease or other flammable materials from accumulating

on hood or filter and to avoid grease fires.

When flaming foods under the hood, turn the fan on.

Cleaning Safety

Clean cooktop with caution. Turn off all controls and

wait for appliance parts to cool before touching or

cleaning. Use care to avoid steam burns if a wet sponge

or cloth is used to wipe spills on a hot surface. Some

cleaners can produce noxious fumes if applied to a hot

surface.

Clean only parts listed in this guide.

Self-Clean Oven

CAUTION

Before self-cleaning the oven, remove the oven racks,

broiler pan, food and any other utensils. Wipe

spillovers to prevent excessive smoke and flare-ups.

Do not clean door gasket. The door gasket is essential

for a good seal. Care should be taken not to rub,

damage, or move the gasket.

Do not use oven cleaners or oven liners of any kind in

or around any part of the self-clean oven.

8113P630-60 5/3/06, 8:59 AM4

4

Save These Instructions for Future Reference

Important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that when

the oven is engaged in the self-clean cycle, there may

be some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/

or door in the room where the appliance is located

during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where

the fumes from the kitchen could reach. Birds have a

very sensitive respiratory system. Fumes released during

an oven self-cleaning cycle may be harmful or fatal to

birds. Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Jenn-Air’s ventilation system is designed to capture both

cooking fumes and smoke from the cooktop surface. If

the system does not, here are some ducting installation

situations to check:

• 6” diameter round or 3

1

/

4

” x 10” rectangular ducting

should be used for duct lengths 10’-60’.

• There should be a minimum clearance of 6” for

cooktop installed near a side wall.

If there is not an obvious improper installation, there

may be a concealed problem such as a pinched joint,

obstruction in the pipe, etc. Installation is

the responsibility of the installer and

questions should be addressed first by the

installer. The installer should very carefully

check the ducting installation instructions.

• Use the Flow Tester Card provided with

your appliance to check the air flow.

DUCTING INFORMATION

5

CARE & CLEANING

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

Self-Clean Oven

CAUTION

• It is normal for parts of the oven to become hot during a

self-clean cycle.

• To prevent damage to oven door, do not attempt to open

the door when LOCK is displayed.

• Avoid touching door, window or oven vent area during a

clean cycle.

• Do not use commercial oven cleaners on the oven finish

or around any part of the oven. They will damage the

finish or parts.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

It is normal for flare-ups, smoking, or flaming to occur during

cleaning if the oven is heavily soiled. It is better to clean

the oven regularly rather than to wait until there is a heavy

build-up of soil in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

1. Turn off the oven light before cleaning. The oven light may

burn out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide

easily after a self-clean cycle if they are not removed.

Important: Remove the air grille from the cooking surface

before self-cleaning.

3. Clean oven frame, door frame, area outside of gasket, and

around the opening in the door gasket with a nonabrasive

cleaner such as Bon Ami* or detergent and water. The

self-cleaning process does not clean these areas. They

should be cleaned to prevent soil from baking on during

the clean cycle. (The gasket is the seal around the oven

door and window.)

4. To prevent damage, do not clean

or rub the gasket around the oven

door. The gasket is designed to

seal in heat during the clean cycle.

5. Wipe up excess grease or

spill-overs from the oven bottom.

This prevents excessive smoking,

flare-ups or flaming during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

To set Self-Clean:

1. Press Clean pad.

2. REMOVE RACKS will be displayed. Remove the racks.

3. Select CONTINUE using the Quickset pad. The Quickset

pads are located on either side of the control panel

display.

4. Set LIGHT soil level by entering 200 using the number

pads for two hours of cleaning time. Select MEDIUM soil

level using the Quickset pads.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

5. CLEAN, TIME, LOCKED and the cleaning time countdown

will be displayed while the oven is cleaning. OVEN

COOLING will appear in the display when the cleaning

time has been completed and the oven is still locked.

Important: The door lock will disengage approximately one

hour after the cleaning time is completed. OVEN COOLING

will go off in the display when the oven door has unlocked.

To Delay a Self-Clean Cycle:

1. Press Clean pad.

2. REMOVE RACKS will be displayed.

Remove the racks.

3. Select CONTINUE using the Quickset pad.

4. Set LIGHT soil level by entering 200 using the number

pads for two hours of cleaning time. Select MEDIUM soil

level using the Quickset pads.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

5. The door will lock. CLEAN, TIME, LOCKED and the

cleaning time countdown will be displayed

6. After door locks, press the More Options pad.

7. Select DELAY using the Quickset pad.

8. Select the number of hours you want to delay the start of the

self-clean cycle.

9. The delay time and cleaning time will be displayed.

6

Notes:

• If the oven door is left open, CLOSE DOOR will appear in

the display until the door is closed.

• If more than 30 seconds elapse between pressing the

Clean pad and pressing a number pad, the program will

automatically return to the previous display.

• The oven door will be damaged if it is forced to open

during cleaning or cooling process.

• The first few times the oven is cleaned, some smoke and

odor may be detected. This is normal and will lessen or

disappear with use. If the oven is heavily soiled, or if the

broiler pan was accidently left in the oven, excessive

smoke and odor may occur.

• As the oven heats and cools, you may hear sounds of

metal parts expanding and contracting. This is normal

and will not damage your appliance.

After Self-Cleaning

About one hour after the end of the clean cycle, the lock

will disengage and OVEN COOLING will go off in the

display. At this point, the door can be opened.

Some soil may leave a light gray, powdery ash which can be

removed with a damp cloth. If soil remains, it indicates that

the clean cycle was not long enough. The soil will be removed

during the next clean cycle.

If the oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and embossed rack

supports with a small amount of vegetable oil to restore ease

of movement.

A white discoloration may appear after cleaning if acidic or

sugary foods were not wiped up before the clean cycle. This is

normal and will NOT affect performance.

Cont.

PART PROCEDURE

CAUTION

Cleaning Procedures

• Be sure appliance is off and all parts are cool before handling

or cleaning. This is to avoid damage and possible burns.

• To prevent staining or discoloration, clean appliance after each use.

• If a part is removed, be sure it is correctly replaced.

Access Panel The access panel is easily removed. To open panel, grasp sides and pull upward, lifting out.

To close panel, align catches with the studs on the range. Press the access panel

forward onto the studs and drop downward to engage.

• Wash with soap and water, a glass cleaner, or mild liquid sprays.

• Do not use excessive amounts of water.

• To prevent scratching or dulling of the finish, do not use mildly abrasive, harsh or

caustic cleaners such as oven cleaners.

Important: To avoid the possibility of accidentally disconnecting any part of the

ventilation system, do not use the area behind the access panel for storage.

Control Panel • To activate control lock for cleaning, see Locking the Control, page 18.

• Wipe with damp cloth. Dry thoroughly.

• Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on control pads and

display area.

• Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel.

Control Knobs • Remove knobs in the OFF position by pulling forward.

• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

• Turn on each element to be sure the knobs have been correctly replaced.

* Brand names are registered trademarks of the

respective manufacturers.

** To order call 1-800-JENNAIR (1-800-536-6247).

GREASE

CUP

STUDS

CATCHES

8113P630-60 5/3/06, 8:59 AM7

7

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

** To order direct, call 1-800-JENNAIR (1-800-536-6247).

PART PROCEDURE

Cooktop – Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia.

Glass-Ceramic Important: Call an authorized servicer if the glass-ceramic top should crack, break or if metal or

aluminum foil should melt on the cooktop.

• Allow the cooktop to cool before cleaning.

• General – Clean cooktop after each use, or when needed, with a damp paper towel and Cooktop Cleaning

Creme* (Part No. 20000001)**. Then buff with a clean, dry cloth.

Important: Permanent stains will develop if soil is allowed to cook on by repeatedly using the cooktop when soiled.

• Heavy Soils or Metal Marks – Dampen a “scratchless” or “never scratch” scrubber sponge. Apply

Cooktop Cleaning Creme* and scrub to remove as much soil as possible. Apply a thin layer of the creme over

the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3 hours for very heavy soil). Keep

moist by covering the paper towel with plastic wrap. Scrub again, then buff with a clean, dry cloth.

Important: Only use a CLEAN, DAMP “scratchless” pad that is safe for non-stick cookware. The pattern and

glass will be damaged if the pad is not damp, if the pad is soiled, or if another type of pad is used.

• Burned-On or Crusty Soils – Scrub with a “scratchless” or “never scratch” scouring pad and

Cooktop Cleaning Creme*.

Important: Hold a razor blade scraper at 30

°

angle and scrape any remaining soil. Then, clean as described

above. Do not use the razor blade for daily cleaning as it may wear the pattern on the glass.

• Melted Sugar or Plastic – Immediately turn element to LOW and scrape sugar or plastic

from hot surface to a cool area. Then turn element OFF and allow to cool. Clean residue

with razor blade scraper and Cooktop Cleaning Creme*.

Oven Window • Avoid using excessive amounts of water which may seep under or behind glass causing staining.

and Door - • Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a

Glass cloth first.

• Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will

scratch glass.

Oven Interior • Follow instructions on pages 5-6 to set a self-clean cycle.

Oven Racks • Clean with soapy water.

• Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

• Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean operation.

If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease

of movement, then wipe off excess oil.

Stainless Steel • DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.

(select models) • DO NOT USE ABRASIVE OR ORANGE CLEANERS.

• ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

• Daily Cleaning/Light Soil –– Wipe with one of the following - soapy water, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse

and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.

20000008)**.

• Moderate/Heavy Soil –– Wipe with one of the following - Bon Ami, Smart Cleanser, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi-

purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

• Discoloration –– Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse

immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

8113P630-60 5/3/06, 8:59 AM8

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

** To order direct, call 1-800-JENNAIR (1-800-536-6247).

PART PROCEDURE

Grill

Accessories:

Basin and The basin pan and basin are located under the grill element and/or cartridges. Clean after each use of the grill.

Basin Pan – • To remove light soil, clean with soapy water or spray with cleansers such as Fantastik* or Formula 409*. For

Porcelain easier cleanup: a) spray with a household cleanser; b) cover with paper towels; c) add small amount of hot

water to keep the paper towels moist; d) cover and wait 15 minutes; and e) wipe clean.

• To remove moderate soil, scrub with Bon Ami*, a soft scrub cleanser or plastic scrubber.

• Basin liner pan can be cleaned in the dishwasher.

Important: Check the grease drain after each use of the grill. To clean, pour about

1

/

3

cup of very hot tap

water mixed with 1 teaspoon dish detergent down the drain.

Element • Never immerse in water. Most soil will burn off during use. The terminal block may be wiped with warm,

soapy water. Do not use abrasive cleaners or materials. Dry thoroughly before reinserting in the cooktop.

Grates – Cast • Wash cool grates (DO NOT IMMERSE HOT GRILL GRATES IN WATER) with detergent in hot water in the

aluminum sink or wash them in the dishwasher. Be sure to remove all food residue before cooking on the grill

coated with grates again.

non-stick • Remove stubborn soils with a plastic mesh puff or pad. Use only those cleaning products which state

finish they are recommended for use when cleaning nonstick surfaces.

• If grates were washed in the dishwasher, season with oil prior to grilling.

• Do not use metal brushes or abrasive scouring pads or other scrubbers intended to clean outdoor charcoal

grills. These will remove the finish as well as scratch the grates. Do not clean in self-cleaning oven or use

oven cleaners on the grates.

Grease Cup • The container is located on the left side behind the bottom access panel, underneath

the range. (See page 6 for opening access panel.) It collects grease and other

liquids created while grilling or using some of the accessories. Check each time after

grilling and empty when grease is noticeable. To remove, simply grasp the handle,

and pull from the bracket holding the container.

• The container can be washed in hot, soapy water or in the dishwasher.

8

MAINTENANCE

CAUTION

Oven Door

NEVER place excessive weight on or stand on an open

oven door. This could cause the range to tip over, break

the door, or injure the user.

• NEVER attempt to open or close door or operate oven until

door is properly replaced.

• NEVER place fingers between hinge and front oven frame.

Hinge arms are spring mounted. If accidentally hit, the

hinge will slam shut against oven frame and could injure

your fingers.

To remove:

1. When cool, open the oven door to the broil stop position

(opened about four inches).

2. Grasp door at each side. Do not

use the door handle to lift door.

3. Lift up evenly until door clears

hinge arms.

To replace:

1. Grasp door at each side.

2. Align slots in the door with the hinge arms on the range.

3. Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top

corners of the door to completely seat door on hinges.

Door should not appear crooked.

Important: The oven door on a new range may feel “spongy”

when it is closed. This is normal and will decrease with use.

Cont.

8113P630-60 5/3/06, 8:59 AM9

9

Oven Window

Leveling Legs

ANTI-TIP BRACKET

LEVELING LEG

Be sure the anti-tip bracket secures one of the rear

leveling legs to the floor. This bracket prevents the range

from accidentally tipping.

Be sure the range is leveled when installed. If

the range is not level, turn the leveling legs,

located at each corner of the range, until range

is level.

ANTI-TIP BRACKET

LEVELING LEG

CAUTION

To assure the proper replacement bulb is used, order bulb

from Jenn-Air. Call 1-800-JENNAIR (1-800-536-6247), ask for

part number 74004458 - halogen bulb.

To Replace Oven Light Bulb:

1. Disconnect power to the appliance.

2. When oven is cool, use fingertips to grasp edge of bulb

cover. Pull out and remove.

3. Carefully remove old bulb by pulling straight out of

ceramic base.

4. To avoid damaging or decreasing the life of the new bulb,

do not touch the bulb with bare hands or fingers. Hold

with a dry cloth or paper towel. Push new bulb prongs

straight into small holes of ceramic base.

5. Replace bulb cover by snapping into place.

6. Reconnect power to the oven. Reset clock.

Oven Light

CAUTION

10

TROUBLESHOOTING

For most concerns, try these first. • Check if oven controls have been properly set.

• Check to be sure plug is securely inserted into receptacle.

• Check or re-set circuit breaker. Check or replace fuse.

• Check power supply.

Part or all of appliance does • Check if surface and/or oven controls have been properly set. See pgs. 12 & 19.

not work. • Check if oven door is unlocked after self-clean cycle. See pg. 5.

• Check if oven is set for a delayed cook or clean program. See pgs. 19 & 5.

• Check if Control Lock is activated. See pg. 18.

• Check if control is in Sabbath Mode. See pg. 31.

Clock, indicator words, and/or • Oven may be set for a Cook & Hold or delay function.

lights operate but oven does • Control Lock may have been set. See pg. 18.

not heat.

Baking results are not as • Make sure the oven vent has not been blocked. See pg. 23 for location.

expected or differ from • Check to make sure range is level.

previous oven. • Temperatures often vary between a new oven and an old one. As ovens age, the oven

temperature often “drifts” and may become hotter or cooler. See pg. 31 for

instructions on adjusting the oven temperature. Important: It is not recommended

to adjust the temperature if only one or two recipes are in question.

Food is not broiling properly or • Check oven rack positions. Food may be too close to element.

smokes excessively. • Broil element was not preheated.

• Aluminum foil was incorrectly used. Never line the broiler insert with foil.

• Oven door was closed during broiling. Leave the door open to the first stop position

(about 4 inches).

• Trim excess fat from meat before broiling.

• A soiled broiler pan was used.

• Voltage in house may be low.

Oven will not self-clean. • Check to make sure the cycle is not set for a delayed start. See pg. 5.

• Check if door is closed.

• Check if control is in Sabbath Mode. See pg. 31.

• Oven may be over 400° F. Oven temperature must be below 400° F to program a

clean cycle.

Oven did not clean properly. • Longer cleaning time may be needed.

• Excessive spillovers, especially sugary and/or acidic foods, were not removed prior

to the self-clean cycle.

Oven door will not unlock after • Oven interior is still hot. Allow about one hour for the oven to cool after the

self-clean cycle. completion of a self-clean cycle. The door can be opened when the LOCK indicator

word is not displayed.

• The control and door may be locked. See pg. 18.

There are no beeps and • Oven may be in Sabbath Mode. See pg. 31.

no display.

PROBLEM SOLUTION

Cont.

8113P630-60 5/3/06, 8:59 AM11

11

Smoothtop surface 1.Tiny scratches or abrasions.

shows wear. • Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans

across top. Make sure pan bottom is not rough. Use the recommended cleaning

agents. See page 7.

2.Metal marks.

• Do not slide metal pans across top. When cool, clean with Cooktop Cleaning Creme.

See page 7.

3.Brown streaks and specks.

• Remove spills promptly. Never wipe with a soiled cloth or sponge. Make sure cooktop

and pan bottom are clean.

4.Areas with a metallic sheen.

• Mineral deposits from water and food. Use recommended cleaning agents. See page 7.

5.Pitting or flaking.

• Remove sugary boilovers promptly. See page 7.

Moisture collects on oven • This is normal when cooking foods high in moisture.

window or steam comes from • Excessive moisture was used when cleaning the window.

oven vent.

There is a strong odor or light • This is normal for a new range and will disappear after a few uses. Initiating a clean

smoke when oven is turned on. cycle will “burn off” the odors more quickly.

• Turning on a ventilation fan will help remove the smoke and/or odor.

• Excessive food soils on the oven bottom. Use a self-clean cycle.

Grill heating element or • Surface controls may not be set properly.

cooktop does not get • Voltage to house may be low.

hot enough.

Ventilation system is not • Check on cross ventilation in room or make up air.

capturing smoke efficiently. • Excessive amount of smoke is being created; check instructions for grilling, trimming

meats. See pg. 14.

• Outside wall cap may be trapped shut.

• Range may be improperly installed; check ducting information. See pg. 4.

• Air filter may be improperly installed. See pg. 15.

Fault Codes • The oven may detect a fault during programming or during operation. If a fault is

detected, the message FAULT DETECTED - PRESS POWER TO CLEAR or FAULT

DETECTED - PRESS ENTER TO TRY AGAIN may appear. Follow directions in the display.

If the fault reappears or does not clear, call an authorized servicer or the toll-free number

in the display.

• If the same operation is attempted before having the wall oven repaired, the message

FEATURE NOT AVAILABLE will appear. The feature will remain inoperable until service

is obtained.

• If the oven is heavily soiled, excessive flareups may result in a fault code during cleaning.

Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then

reset the clean cycle. If the fault code reappears, contact an authorized servicer.

Noises may be heard. • The oven makes several low-level noises. You may hear the oven relays as they go on

and off. This is normal.

• As the oven heats and cools, you may hear sounds of metal parts expanding and

contracting. This is normal and will not damage your appliance.

SAb flashing and then • Oven is in Sabbath Mode. To cancel, press and hold the Setup pad for five

displayed continuously. seconds.

PROBLEM SOLUTION

8113P630-60 5/3/06, 8:59 AM12

12

SURFACE COOKING

Surface Controls

Use to turn on the surface elements. An infinite choice of

heat settings is available from Low to High. The knobs can

be set on or between any of the settings.

Medium (5): Use to

maintain slow boil for

large amounts of liquids

and for most frying

operations.

BEFORE COOKING

• Always place a pan on the surface unit before you turn it

on. To prevent damage to range, never operate surface

unit without a pan in place.

• NEVER use the cooktop as a storage area for food or

cookware.

DURING COOKING

• Be sure you know which knob controls which surface

unit. Make sure you turned on the correct surface unit.

• Begin cooking on a higher heat setting then reduce to a

lower setting to complete the operation. Never use a

high heat setting for extended cooking.

• NEVER allow a pan to boil dry. This could damage the

pan and the appliance.

• NEVER touch cooktop until it has cooled. Expect some

parts of the cooktop, especially around the surface units,

to become warm or hot during cooking. Use potholders

to protect hands.

CAUTION

Suggested Heat Settings

The size, type of cookware and cooking operation will affect

the heat setting.

AFTER COOKING

• Make sure surface unit is turned off.

• Clean up messy spills as soon as possible.

OTHER TIPS

• If cabinet storage is provided directly above cooking

surface, limit it to items that are infrequently used and

can be safely stored in an area subjected to heat.

Temperatures may be unsafe for items such as volatile

liquids, cleaners or aerosol sprays.

• NEVER leave any items, especially plastic items, on the

cooktop. The hot air from the vent may ignite flammable

items, melt or soften plastics, or increase pressure in

closed containers, causing them to burst.

• NEVER allow aluminum foil, meat probes or any other

metal object, other than a pan on a surface element, to

contact heating elements.

• NEVER store heavy items above the cooktop that could fall

and damage it.

Low (1): Use to keep foods

warm and melt chocolate

and butter.

High (9): Use to bring

liquid to a boil. Always

reduce setting to a lower

heat when liquids begin to

boil or foods begin to cook.

Med. Low (3):

Use to

continue

cooking

covered foods

or steam foods.

Med. High (7): Use to

brown meat, heat oil for

deep fat frying or

sauteing. Maintain fast

boil for large amounts

of liquids.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

• The control panel is marked to identify which

element the knob controls. For example, the

graphic at right indicates right front element.

3. There is an element indicator light on the control panel.

When any surface control knob is turned on, the light will

turn on. The light will turn off when all the surface

elements are turned off.

When a control is turned on, a glow can be seen through

the smoothtop surface. The element will cycle on and off

to maintain the preset heat setting, even on High.

4. After cooking, turn knob to OFF. Remove pan.

Setting the controls for grilling:

Knob A - Exhaust fan only. Knob will not operate the grill

element.

Knob B - Exhaust fan and grill element.

Setting the controls for cartridges:

Knob A - Left front element.

Knob B - Left rear element.

A B

8113P630-60 5/3/06, 8:59 AM13

13

Cooktop cartridges, either conventional coil or radiant

element, can be installed on either side of the range. (See

page 33 for all available cartridges and accessories, and their

model numbers.)

To Install Cartridges:

1. If the grill grates, element, and/or basin pan are in place,

remove before installing a cooktop cartridge. Clean

porcelain basin of any grease accumulation. (See page 8

for cleaning recommendations.)

2. To install any of the optional cooktop cartridges, be sure

controls are turned off and the cartridge is cool. Position

the cartridge terminal plug toward the terminal receptacle.

This receptacle is located at the front of the left side and at

the back of the right side of the range.

3. Slide the cartridge toward the receptacle until the

cartridge terminal plug is completely engaged.

4. Lower the opposite end of the cartridge into the rangetop

until it is flush with the surface. Your range is now ready

to use.

To Remove Cartridges:

1. Controls must be off and the cartridge should be cool.

2. Lift up the edge of the cartridge until top of cartridge

clears the opening on the range by about 2 inches.

Important: Lifting the cartridge too high while still

engaged in the receptacle could damage the terminal

plug.

3. To disengage terminal, hold cartridge by the sides and pull

away from the terminal receptacle. Lift out when fully

unplugged.

4. Do not stack cartridges where they may fall or be

damaged. Never store other materials on top of the glass-

ceramic cartridges since this could damage or scratch the

surface.

Home Canning

Canning should be done on the conventional coil cartridge

only. Canning element accessory, Model A145A, makes it

possible to use large oversized canners with the conventional

coil cartridge.

For additional information, refer to the Use and Care Guide

packaged with your cartridge.

14

Using the Grill

Grilling Tips

• Be sure to follow directions for using the grill.

• Suggested cooking times and control settings (see page

15) are approximate due to variations in the foods and

electrical voltage.

• For best results, buy top grade meat. Meat that is at least

3

/

4

inch will grill better than thinner cuts.

• Score fat on edges of steak, but do not cut into meat, to

prevent curling while cooking.

• For the attractive “branded” look on steaks, be sure grill is

preheated. Allow one side of meat to cook to desired

doneness, or until juices appear on the top surface, before

turning. Turn steaks and hamburgers just once.

Manipulating food causes loss of juices.

• When basting meats or applying sauces to foods,

remember that excessive amounts accumulate inside your

grill and do not improve the food flavor.

Apply sauces during the last 15 to 20 minutes of cooking

time unless recipe specifies otherwise. Plus, anytime a

sugar-based marinade (for example barbecue sauce) is

going to be used, the grates should be “seasoned” prior to

preheating. (See Using the Grill section.)

• There are many meat marinades which will help tenderize

less expensive cuts of meat for cooking on the grill.

• Certain foods, such as poultry and non-oily fish, may need

some extra fat. Brush with oil or melted butter occasionally

while grilling.

• Use tongs with long handles or spatulas for turning meats.

Do not use forks as these pierce the meat, allowing juices

to be lost.

• Before the first use, wash your new grill grates in hot

soapy water, rinse and dry. Then “season” the surface by

wiping on a thin coating of cooking oil. Remove excess oil

by wiping with paper towel.

This procedure should be repeated when either:

a)cleaning in the dishwasher since the detergent may

remove seasoning or

b)anytime a sugar-based marinade (for example,

barbecue sauce) is going to be used.

• Preheat the grill on High for 5 minutes. Preheating

improves the flavor and appearance of meats and quickly

sears the meat to help retain the juices.

• Use nonmetallic spatulas or utensils to prevent damaging

the nonstick grill grate finish.

• Excessive amounts of fat should be trimmed from meats.

Only a normal amount is necessary to produce the smoke

needed for that smoked, “outdoor” flavor. Excessive fat can

create cleaning and flare-up problems.

• Allowing excessive amounts of grease or drippings to

constantly flare-up voids the warranty on the grill grates.

• Excessive flare-ups indicate that either the grill interior

needs to be cleaned, that excessive amounts of fat are in

the meat or the meat was not properly trimmed.

• Grease drippings will occasionally ignite to produce

harmless puffs of flame for a second or two. This is a

normal part of the cooking process. Important: For

information on the grease cup, see page 8.

• NEVER LEAVE GRILL UNATTENDED DURING

GRILL OPERATION.

• Should excess grease cause sustained flare-ups:

1. Turn on the fan manually.

2. Immediately turn grill controls to OFF.

3. Remove meat from grill.

Notes:

• Do not use aluminum foil inside the grill

area.

• Do not use charcoal or wood chips in

the grill area.

• Do not allow grill basin pan to

become overloaded with grease.

Clean frequently.

• Do not cover grates completely with meat. Leave air

space between each steak, etc. to allow proper

ventilation as well as prevent flare-ups.

Ventilation System

The built-in ventilation system removes cooking vapors, odors

and smoke from foods prepared on your cooktop and grill.

• To operate the ventilation

system manually, push the

Vent Fan pad located on the

electronic control. Push once

for Low, push again for High

and a third time to turn the

fan Off.

• The ventilation system will operate automatically when the

grill element is in use.

• The fan can be used to remove strong odors from the

kitchen, as when chopping onions near the fan.

➞

Cont.

8113P630-60 5/3/06, 8:59 AM15

15

Care and Cleaning of the

Ventilation System

• Air Grille: The air grille lifts off easily. Wipe clean or wash in

dishwasher or sink with mild household detergents. To

prevent scratching the surface, do not use abrasive

cleaners or scrubbing pads.

• Filter: Turn off ventilation system before removing. The filter

is a permanent type and should be cleaned when soiled.

Clean in sink with warm water and detergent or in

dishwasher.

IMPORTANT: DO NOT OPERATE SYSTEM WITHOUT

FILTER. Filter should always be placed at an angle. As you

face the front of the range, the top of the filter should rest

against the left side of the vent opening. The bottom should

rest against the right side of the vent chamber at the

bottom. Important: If filter is flat against the fan wall,

ventilation effectiveness is reduced.

AIR FILTER

• Ventilation Chamber: This area, which houses the filter,

should be cleaned in the event of spills or whenever it

becomes coated with a film of grease. It can be cleaned with

paper towel, damp cloth, or sponge and mild household

detergent or cleanser.

Important: The oven vent is located under the right side of

the air grille. When using or cleaning the oven, hot and

moist air may be noticed in this area. The area near the vent

may become hot enough to cause burns. Be careful not to

spill anything into this vent. The air grille must be

removed before the self-clean cycle.

Preheat grill on High 5 minutes, for best flavor.

FOODS SETTING COOKING TIME PROCEDURE

Steak: (1 - 1

1

/

4

”) Rare High 10 to 17 minutes Turn after 8 to 10 minutes.

Medium High 20 to 25 minutes Turn after 13 to 15 minutes.

Well High 25 to 32 minutes Turn after 15 to 17 minutes.

Hamburgers: (3-4 oz.) 9 15 to 25 minutes Turn after half the time.

Pork Chops: (

1

/

2

-

3

/

4

”) 9 25 to 40 minutes Turn occasionally.

Ham Slices: (

1

/

2

”) High 10 to 15 minutes Turn once.

Fully-cooked Sausages: Hot Dogs High 5 to 15 minutes Turn occasionally.

Polish High 10 to 20 minutes Turn once.

Fresh Sausage: Links & Patties 9 15 to 20 minutes Turn occasionally.

Chicken: Boneless Breasts 9 25 to 35 minutes Turn occasionally.

Bone-in Breasts, Drumsticks 9 45 to 60 minutes Turn occasionally. Brush with marinade

and Thighs or glaze during last 10 minutes.

Fish: Steaks (1”) 9 20 to 30 minutes Brush with butter. Turn after half the time.

Shrimp: (Skewered) 9 8 to 12 minutes Turn and brush with butter or marinade

frequently.

Garlic Bread, Bruschetta High 2 to 4 minutes Turn after half the time.

Hot Dog Buns, Hamburger Buns 9 2 to 3 minutes

Fruits & Vegetables: Pineapple Rings High 8 to 10 minutes Turn after half the time.

Pepper Rings High 7 to 9 minutes Brush with oil. Turn after half the time.

(

1

/

2

” Rings) High 8 to 12 minutes Brush with butter. Turn occasionally.

(

1

/

2

” Lengthwise

Slices)

Grill Guide

Important: This chart is a suggested guide. Cooking times and control settings are approximate due to variations in meats,

control switches, and voltage.

8113P630-60 5/3/06, 8:59 AM16

16

Canning and Oversize Cookware

All canners and large pots must have flat bottoms and

must be made from heavy-gauge materials. This is critical

on smoothtop surfaces. The base must not be more than

1 inch larger than the element.

When canners and pots do not meet these standards, cooking

times may be longer, and cooktops may be damaged.

Some canners are designed with smaller bases for use on

smoothtop surfaces.

When canning, use the High heat setting only until the

water comes to a boil or pressure is reached in the canner.

Reduce to the lowest heat setting that maintains the boil or

pressure. If the heat is not turned down, the cooktop may be

damaged.

Tips to Protect the

Smoothtop Cartridge Surface

Cleaning (see page 7 for more information)

• Before first use, clean the cooktop.

• Clean your cooktop daily or after each use. This will keep your

cooktop looking good and can prevent damage.

• If a spillover occurs while cooking, immediately clean the spill

from the cooking area while it is hot to prevent a tough

cleaning chore later. Using extreme care, wipe spill with a

clean, dry towel.

• Do not allow spills to remain on the cooking area or the

cooktop trim for a long period of time.

• Never use abrasive cleansing powders or scouring pads

which will scratch the cooktop.

• Never use chlorine bleach, ammonia or other cleansers not

specifically recommended for use on glass-ceramic.

To Prevent Marks & Scratches

• Do not use glass pans. They may scratch the surface.

• Never place a trivet or wok ring between the surface and pan.

These items can mark or etch the top.

• Do not slide aluminum pans across a hot surface. The pans

may leave marks which need to be removed promptly. (See

Cleaning, page 7.)

• Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

• To prevent scratching or damage to the glass-ceramic top, do

not leave sugar, salt or fats on the cooking area. Wipe the

cooktop surface with a clean cloth or paper towel before

using.

• Never slide heavy metal pans across the surface since these

may scratch.

To Prevent Stains

• Never use a soiled dish cloth or sponge to clean the cooktop

surface. A film will remain which may cause stains on the

cooking surface after the area is heated.

• Continuously cooking on a soiled surface may/will result in a

permanent stain.

To Prevent Other Damage

• Do not allow plastic, sugar or foods with high sugar content

to melt onto the hot cooktop. Should this happen, clean

immediately. (See Cleaning, page 7.)

• Never let a pan boil dry as this will damage the surface and

pan.

• Never use cooktop as a work surface or cutting board.

• Never cook food directly on the surface.

• Do not use a small pan on a large element. Not only does this

waste energy, but it can also result in spillovers burning onto

the cooking area, which requires extra cleaning.

Cookware Recommendations

• Do not use non-flat specialty items that are oversized or

uneven such as round bottom woks, rippled bottom and/or

oversized canners and griddles.

• Do not use foil or foil-type containers. Foil may melt onto the

glass. If metal melts on the cooktop, do not use. Call an

authorized Jenn-Air Servicer.

Select Avoid

Flat, smooth-bottom Pans with grooved or warped bottoms.

pans. Pans with uneven bottoms do not cook

efficiently and sometimes may not

boil liquid.

Heavy-gauge pans. Very thin-gauge metal or glass pans.

Pans that are the Pans smaller or larger than the

same size as the element by 1 inch.

element.

Secure handles. Cookware with loose or broken handles.

Heavy handles that tilt the pan.

Tight-fitting lids. Loose-fitting lids.

Flat bottom woks. Woks with a ring-stand bottom.

Using the right cookware can prevent many problems, such as

food taking longer to cook or achieving inconsistent results.

Proper pans will reduce cooking times, use less energy, and

cook food more evenly.

Flat Pan Tests

The Ruler Test:

1. Place a ruler across the bottom of the pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put 1 inch of water in the pan. Place on cooktop and turn

control to High.

2. Watch the formation of the bubbles as the water heats.

Uniform bubbles mean good performance, and uneven

bubbles indicate hot spots and uneven cooking.

8113P630-60 5/3/06, 8:59 AM17

17

OVEN COOKING

A Rapid Preheat Use to decrease preheating time.

B Convect Use for convection baking and roasting.

C Bake Use for baking and roasting.

D Broil Use for broiling and top browning.

E TIMER 1 Sets timer.

F Display Displays oven functions, options and

window time of day.

G TIMER 2 Sets timer.

H Number Pads Use to enter time and temperature,

or to enter Favorites names.

I Favorites Use to access, program or save

baking cycles.

J More Options Use to access additional features.

K Clean Use to set self-clean cycle.

L Setup Use to view or change factory

default settings.

M Vent Fan Activates the ventilation fan on

the cooktop.

N Oven Light Use to turn the oven light on or off.

O CANCEL Cancels all operations except Timer,

Clock, Favorites, Setup and Vent Fan.

P Quickset pads Use to select options in display

window (next to display window

on both sides).

The control panel is designed for ease in programming. The display window shows options for each function and moves from step

to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake

operation.

A B C D E F G H

Control Panel

Quickset Pads

Quickset pads are located on each side of the display window

and are used to select the desired function or option in the

display window. To select the option or function, press the

Quickset pad next to the word.

Important: Four seconds after entering the function,

option, number or letter, the function will automatically be

entered. If more than 30 seconds elapse between steps in

programming, the function will be canceled and the

display will return to the previous display.

Clock

Setting the Clock:

1. Press the Setup pad.

2. Select CLOCK using the Quickset pads.

3. Select TIME.

4. Enter the time using the number pads.

5. Press Enter pad.

6. Select AM or PM in 12 hour mode. (For 24 hour clock, see

page 18.)

7. To exit the Setup mode, press Setup pad.

If you need to back out of a function or option in the display,

press the Back pad. When your programming is complete,

press the Enter pad or wait four seconds and the function will

start automatically.

Up arrows indicate additional screens with additional options.

Press the Quickset pads next to the arrows to scroll through

the display.

I J K L M N O P

8113P630-60 5/3/06, 8:59 AM18

18

Activating and canceling the clock/day

of week display:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DISABLE is displayed.

4. Select DISABLE.

5. Select OFF to turn the clock display off, or select ON to turn

the clock display on.

6. Select OFF to turn the day of the week display off. Select

ON to turn the weekday display on.

7. To exit the Setup mode, press Setup pad.

Entering the day of the week:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DAY is displayed.

4. Use Quickset arrow to scroll through the days.

5. To exit the Setup mode, press Setup pad.

To set the clock for a 12 or 24 hour format:

The clock can be set to display time in either a 12 hour or 24

hour format.

1. Press the Setup pad.

2. Select CLOCK.

3. Use the arrow to scroll to the next screen.

4. Select 12/24 HOUR.

5. Select 12 HR or 24 HR.

6. To exit Setup mode, press Setup pad.

Timers

Setting the Timers (Timer 1 or Timer 2):

1. Press TIMER 1 or TIMER 2 pad.

2. Press one of the displayed times using the

Quickset pads, or press the number pads to

enter the desired time.

Important: Each press of the displayed time choices adds

additional time. For example, pressing “10 MIN” three

times provides 30 minutes on the timer (0:30).

3. Press Enter pad.

Changing the amount of time entered once the

Timer starts:

1. Press the TIMER 1 or TIMER 2 pad once.

2. Press the displayed times on the Quickset

pads until the desired time is entered.

OR

3. Press the number pads to enter the new desired time.

4. Press Enter pad.

Canceling the Timer:

Press the TIMER 1 or TIMER 2 pad twice.

If both Timers are active:

If the desired Timer is already in the foreground, press once

for edit mode and twice to cancel the Timer. If the desired

Timer is not in the foreground, follow the steps below.

1. Press the desired TIMER pad once. The selected Timer will

come to the foreground.

2. Press the TIMER pad a second time to access the edit

mode in order to make changes.

3. Pressing the TIMER pad a third time will cancel the Timer.

Changing the Timer beeps:

The signal beeps for TIMER 1 and TIMER 2 can be changed.

The options available are two beeps every thirty seconds, two

beeps every sixty seconds or one beep only. The default

setting is one beep.

1. Press the Setup pad.

2. Select the arrow to scroll until TONES

is displayed.

3. Select TONES.

4. Select TIMERS TONES.

5. Select the desired timer beep format (2-30 SEC, 2-60 SEC

or 1 BEEP).

6. Press Setup pad to exit Setup mode.

Locking the Control and Oven Door

The oven control and oven door can be locked to prevent

accidental programming. If an oven function is currently

being used, the control and door cannot be locked.

To lock the control and door:

Press the Back and Enter pads at the same time, holding for

three seconds or until CONTROL LOCKED appears in the

display.

To unlock the control and door:

Press the Back and Enter pads at the same time, holding for

three seconds. UNLOCKING DOOR will appear in the display

when the control and door are unlocking.

8113P630-60 5/3/06, 8:59 AM19

19

Notes:

• If more than thirty seconds elapse between pressing a

pad and pressing a number pad, the display will return

to the previous display.

• Whenever the temperature appears in the display, the

oven is heating.

• To change the oven temperature during cooking, press

the Bake pad and select a displayed temperature or use

the number pads to enter the desired temperature.

• The oven will automatically shut off after 12 hours if it is

accidentally left on. To set a Sabbath Mode, see Sabbath

Mode, page 31.

time. When that time has elapsed, the oven will automatically

reduce temperature to 170° F and keep the food warm for up

to an hour and then automatically turn off.

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time. When that time has elapsed, the oven will keep the food

warm for up to an hour then automatically turn off.

To set Cook & Hold (select models):

• The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature. Allow about 15 minutes for the oven

to preheat.

• When the oven is preheated, the oven will beep and

PREHEAT will no longer be displayed.

3. At the end of cooking, turn the oven off by

pressing the CANCEL pad. Remove food

from the oven. The oven will continue

operating until the CANCEL pad is pressed.

Baking

To set Bake:

1. Press the Bake pad.

2. Select the oven temperature using the Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 170° F to 550° F

in 5° increments.

• After three seconds, the oven will begin to preheat.

BAKE and PREHEAT will appear in the display along

with 100° or the actual oven temperature, whichever

is higher.

To set a Delay:

1. After Bake has been programmed, press

the More Options pad.

2. Select DELAY.

3. Select the amount of time you want to delay the start of

cooking using the displayed times or the number pads.

4. Select the amount of time you want to cook using the

displayed times or the number pads.

5. The display will show BAKE, the temperature, the delay

time and the cook time countdown.

6. When the delay time has expired, the oven will begin

heating. COOK TIME, the cook time countdown, PREHEAT,

BAKE and the actual oven temperature will be displayed.

CAUTION

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry or seafood.

Bake Options

Cook & Hold (select models) and Delay options are available

when baking. When using the Cook & Hold option (select

models), the oven begins to heat immediately after the control

has been set. Then, the oven cooks for a specified length of

1. After Bake has been programmed, press

the More Options pad.

2. Select COOK/HLD.

3. Select the amount of time you want to bake by pressing

the Quickset pads or the number pads.

4. Press Enter pad.

5. COOK TIME, the cook time countdown, PREHEAT, BAKE

and the actual temperature will be displayed.

The oven will cook for the selected time, then keep food warm

for one hour.

8113P630-60 5/3/06, 8:59 AM20

La page charge ...

Jenn-Air Range ELECTRIC DOWNDRAFT SLIDE-IN RANGE Manuel utilisateur

Jenn-Air Range ELECTRIC DOWNDRAFT SLIDE-IN RANGE Manuel utilisateur

dans d''autres langues

Documents connexes