Rinnai RUCS65i series Guide d'installation

Catégorie
Chauffe-eau
Taper
Guide d'installation

Ce manuel convient également à

Direct Vent Tankless Water Heater
Installaon and Operaon Manual










WARNING

This manual provides informaon on the installaon, operaon, and maintenance of the water heater. For proper
operaon and , it is important to follow the instrucons and adhere to the safety precauons.
A licensed professional must install the water heater according to the exact instrucons in this manual.
The consumer must read the enre manual to properly operate the water heater and to have regular maintenance
performed.

FOR INDOOR APPLICATIONS ONLY
RUCS65i ................ --
RUCS75i ................ --
FOR OUTDOOR APPLICATIONS ONLY
RUS65e ................. --
RUS75e ................. --



C US
U328-0700
2 KCM Series Manual

This is the safety alert symbol. This symbol alerts you to potenal hazards that can kill or hurt you
and others.
Indicates an imminently hazardous situaon which, if not avoided, will result in personal
injury or death.
Indicates a potenally hazardous situaon which, if not avoided, could result in personal
injury or death.
Indicates a potenally hazardous situaon which, if not avoided, could result in minor or
moderate injury. It may also be used to alert against unsafe pracces.
DANGER
CAUTION
WARNING
Table of Contents ..................................................... 2
Safety Behaviors and Pracces for the
Consumer and Installer ............................................ 3

 .............................
Prepare for Installaon ...................................... 5
Determine Installaon Locaon ........................ 6
Freeze Protecon ............................................. 10
Checklist to Determine Installaon Locaon ... 11
Mount to Wall .................................................. 11
Remove the Front Panel .................................. 11
Installaon of Venng (indoor models only) ... 12
Determining Vent Conguraon ...................... 13
Twin Pipe PVC/CPVC Vent Installaon ............. 20
Condensate ...................................................... 37
Checklist for Venng and Condensate
(indoor models only) ........................................ 37
Installaon of Plumbing ................................... 38
Checklist for Plumbing ..................................... 41
Installaon of Gas Supply ................................ 41
Connect Electricity ........................................... 43
Adjustment for High Altude Installaons ...... 43
Adjustment for Vent Length
(indoor models only) ........................................ 43
Checklist for Gas and Electricity ....................... 43
Installaon of Temperature Controller ............ 44
Final Checklist ................................................... 46
Technical Data ........................................................ 47
Specicaons ................................................... 47
Dimensions ....................................................... 48
Pressure Drop and Water Flow Curves ............ 49
Ladder Diagram ................................................ 50
 ....................................... 
Consumer Operaon Guidelines for the
Safe Operaon of your Water Heater .................... 52
How to set the Temperature ................................. 53
How to use the Oponal Temperature
Controller ........................................................ 54
Diagnosc Codes .................................................... 56
Required Maintenance ........................................... 59
Freeze Protecon and Winterizaon ............... 60
Flushing the Heat Exchanger ............................ 61
Manual Draining of the Water Heater ............. 62
State Regulaons .................................................... 63
Replacement Parts ................................................. 64
Warranty ................................................................. 65
French Version ........................................................ 67


NOTICE: Rinnai somemes shares customer contact informaon with businesses that we believe provide
products or services that may be useful to you. By providing this informaon, you agree that we can
share your contact informaon for this purpose. If you prefer not to have your informaon shared with
these businesses, please contact customer service and ask not to have your informaon shared. We
will however, connue to contact you with informaon relevant to the product(s) you registered and/
or your account with us.
If you have any quesons or feel that the manual is incomplete contact Rinnai at 1-800-621-9419.
KCM Series Manual 3
CAUTION
BURN HAZARD. Hot exhaust and vent may cause
serious burns. Keep away from the water heater
unit. Keep small children and animals away from
the unit.
Hot water outlet pipes leaving the unit can be hot
to touch. In residenal applicaons, insulaon
must be used for hot water pipes below 36” due to
burn risk to children.

Before operang, smell all around the appliance
area for gas. Be sure to smell next to the oor
because some gas is heavier than air and will sele
on the oor.
Keep the area around the appliance clear and free
from combusble materials, gasoline, and other
ammable vapors and liquids.
Combusble construcon refers to adjacent walls
and ceiling and should not be confused with
combusble or ammable products and materials.
Combusble and/or ammable products and
materials should never be stored in the vicinity of
this or any gas appliance.
Always check the water temperature before
entering a shower or bath.
To protect yourself from harm, before performing
maintenance:
Turn o the electrical power supply by
unplugging the power cord or by turning o the
electricity at the circuit breaker. (The
temperature controller does not control the
electrical power.)
Turn o the gas at the manual gas valve, usually
located immediately below the water heater.
Turn o the incoming water supply. This can be
done at the isolaon valve immediately below
the water heater or by turning o the water
supply to the building.
WARNING
Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it; call a
licensed professional. Force or aempted repair
may result in a re or explosion.
Do not use this appliance if any part has been under
water. Immediately call a licensed professional to
inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
Do not use substute materials. Use only parts
cered for the appliance.
Should overheang occur or the gas supply fail to
shut o, turn o the manual gas control valve to the
appliance.
Do not adjust the DIP switch unless specically
instructed to do so.
Do not use an extension cord or an adapter plug
with this appliance.
Any alteraon to the appliance or its controls can be
dangerous and will void the warranty.
Proper venng is required for the safe operaon of
this appliance.
California law requires this noce to be provided:

This product contains chemicals known to the state of California to cause cancer, birth defects, or other
reproducve harm.
WARNING
4 KCM Series Manual
A licensed professional must install the appliance,
inspect it, and leak test it before use. The warranty
will be voided due to any improper installaon.
The installer should have skills such as:
Gas sizing.
Connecng gas lines, water lines, valves, and
electricity.
Knowledge of applicable naonal, state, and
local codes.
Installing venng through a wall or roof.
Training in installaon of tankless water heaters.
(Training can be accessed on-line at
www.trainingevents.rinnai.us)

Prepare for Installaon ...................................... 5
Determine Installaon Locaon ......................... 6
Freeze Protecon ............................................. 10
Checklist to Determine Installaon Locaon ... 11
Mount to Wall .................................................. 11
Remove the Front Panel .................................. 11
Installaon of Venng (indoor models only) ... 12
Condensate (indoor models only) .................... 37
Checklist for Venng and Condensate ............ 37
Installaon of Plumbing ................................... 38
Checklist for Plumbing ..................................... 41
Installaon of Gas Supply ................................. 41
Connect Electricity ........................................... 43
Adjustment for High Altude Installaons ...... 43
Adjustment for Vent Length
(indoor models only) ........................................ 43
Checklist for Gas and Electricity ....................... 43
Installaon of Temperature Controller ............ 44
Final Checklist................................................... 46
 

Do not install the RUCS65i, or the RUCS75i
outdoors.
Do not install the RUS65e, or the RUS75e indoors.
Do not install the appliance in an area where water
leakage of the unit or connecons will result in
damage to the area adjacent to the appliance or to
lower oors of the structure. When such locaons
cannot be avoided, it is recommended that a
suitable drain pan, adequately drained, be installed
under the appliance. The pan must not restrict
combuson air ow.
Do not obstruct the ow of combuson and
venlaon air. Combuson air shall not be
supplied from occupied spaces.
Do not use this appliance in an applicaon such as
a pool or spa heater that uses chemically treated
water . (This appliance is suitable for lling large or
whirlpool spa tubs with potable water.)
Do not use substute parts that are not authorized
for this appliance.

The installaon must conform with local codes or,
in the absence of local codes, with the Naonal
Fuel Gas Code, ANSI Z223.1/NFPA 54, or the
Natural Gas and Propane Installaon Code, CSA
B149.1. If installed in a manufactured home, the
installaon must conform with the Manufactured
Home Construcon and Safety Standard, Title 24
CFR, Part 3280 and/or CAN/SCA Z240 MH Series,
Mobile Homes.
The appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the Naonal Electrical
Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1.
The appliance and its appliance main gas valve
must be disconnected from the gas supply piping
system during any pressure tesng of that system
at test pressures in excess of 1/2 psi (3.5 kPa)
(13.84 in W.C.).

For installaon in residenal applicaons only.
Cered for installaon in manufactured (mobile)
homes.


KCM Series Manual 5

Parts included
Tools needed
Materials needed
The appliance must be isolated from the gas supply
piping system by closing its individual manual
shuto valve during any pressure tesng of the gas
supply piping system at test pressures equal to or
less than 1/2 psi (3.5 kPa) (13.84 in W.C.).
You must follow the installaon instrucons and
those in Care and Maintenance for adequate
combuson air intake and exhaust.

If a water heater is installed in a closed water
supply system, such as one having a backow
preventer in the cold water supply line, means
shall be provided to control thermal expansion.
Contact the water supplier or local plumbing
inspector on how to control thermal expansion.
Should overheang occur or the gas supply fail to
shut o, turn o the manual gas control valve to
the appliance.
Keep the air intake locaon free of chemicals, such
as chlorine or bleach, that produce fumes. These
fumes can damage components and reduce the life
of your appliance.
Tankless water heater
Self Tapping Screws (Qty - 2)
Pipe wrenches (2)
Adjustable pliers
Screwdrivers (2)
Wire cuers
Gloves
Safety glasses
Level
Tools that might be needed
Hammer drill with
concrete bits
Saw
Threading machine with
heads and oiler
Core drill with diamond
head
Torch set
Copper tubing cuer
Steel pipe cuer
Materials that may be needed
Soap or gas leak
detector soluon
Approved venng
Teon tape
(recommended) or pipe
compound
Pressure Relief Valve
Heat tape
Pipe insulaon
Electrical wire and
conduit per local code
Concrete wall anchors
Oponal pipe cover
Oponal temperature
controller (MC-91-2)
PVC glue/cement
5/8” ID PVC exible
tubing
2 conductor 22 AWG
wire for controller
Single gang electrical
box
Wire nuts
Unions and drain valves
Isolaon Valve Kit

6 KCM Series Manual
Consideraon of care for your water heater should
include evaluaon of water quality.









Total Hardness Up to 200 mg / L
Aluminum * Up to 0.2 mg / L
Chlorides * Up to 250 mg / L
Copper * Up to 1.0 mg / L
Dissolved Carbon Dioxide (CO2) Up to 15.0 mg / L or PPM
Iron * Up to 0.3 mg / L
Manganese * Up to 0.05 mg / L
pH * 6.5 to 8.5
TDS (Total Dissolved Solids) * Up to 500 mg / L
Zinc * Up to 5 mg / L

Environment
Air surrounding the water heater, venng, and vent
terminaon(s) is used for combuson and must be free
of any compounds that cause corrosion of internal
components. These include corrosive compounds that
are found in aerosol sprays, detergents, bleaches,
cleaning solvents, oil based paints/ varnishes, and
refrigerants. The air in beauty shops, dry cleaning
stores, photo processing labs, and storage areas for pool
supplies oen contains these compounds. Therefore it
is recommended that outdoor models be used for these
locaons where possible.
The water heater, venng, and vent terminaon(s)
should not be installed in any areas where the air may
contain these corrosive compounds. If it is necessary for
a water heater to be located in areas that may contain
corrosive compounds, the following instrucons are
strongly recommended.

Indoor/Internal Water Heaters
DO NOT Install in areas where air for combuson
might be contaminated with chemicals.
Before installaon, consider where air has the
ability to travel within the building to the water
heater.
Where possible, install the water heater in a sealed
closet so that it is protected from the potenal of
contaminated indoor air.
Chemicals that are corrosive in nature should not
be stored or used near the water heater.
Outdoor/External Water Heaters and Vent
Terminaons of Indoor/Internal Water Heaters
Install the water heater as far away as possible
from exhaust vent hoods.
Install as far away as possible from any air inlet
vents. Corrosive fumes may be released through
these vents when air is not being brought in
through them.
Chemicals that are corrosive in nature should not
be stored or used near the water heater or vent
terminaon.
Damage and repair due to corrosive compounds in the
air is not covered by warranty.
Water Quality
* Source: Part 143 Naonal Secondary Drinking Water Regulaons
If you install this water heater in an area that is known
to have hard water or that causes scale build-up the
water must be treated and may require more frequent
heat exchanger ushing schedule.
When scale build-up in the heat exchanger begins to
aect the performance of the water heater, a diagnosc
code “LC#” will display. Flush the heat exchanger to
prevent damage to it. Scale build up is caused by hard
water and can be accelerated if the unit is set at a high
temperature.
Rinnai oers Southeastern Filtraon’s “ScaleCuer
Water Condioning System” that oers superior lime
scale prevenon and corrosion control by feeding a
blend of control compounds into the cold water supply.
You must ensure that clearances will be met and that
the vent length will be within required limits. Consider
the installaon environment, water quality, and need
for freeze protecon. Requirements for the gas line,
water lines, electrical connecon, and condensate
disposal can be found in their respecve installaon
secons of this manual.
Part Number Descripon
103000038
Southeastern Filtratrion
ScaleCuer System 3/4” Feed
103000039
ScaleCuer Rell
KCM Series Manual 7
INSIDE
CORNER DETAIL
FIXED
CLOSED
OPERABLE
FIXED
CLOSED
OPERABLE
B
B
B
A
J
B
M
C
F
B
B
E
D
L
G
A
H
K
I
[1] A vent shall not terminate directly above a sidewalk or paved driveway
that is located between two single family dwellings and serves both
dwellings.
[2] Permied only if veranda, porch, deck, or balcony is fully open on a
minimum of two sides beneath the oor.
For clearances not specied in ANSI Z223.1/NFPA 54, clearances are in
accordance with local installaon codes and the requirements of the gas
supplier.
Clearance to opposite wall is 24 inches (60 cm).
X
V
AIR SUPPLY INLET
VENT TERMINAL
AREA WHERE TERMINAL
IS NOT PERMITTTED
For indoor models, you must install a vent terminaon to bring in combuson air and expel exhaust to the outside.
SNOW
TERMINATION
Clearance in
Ref. A also
applies to
anticipated
snow line


 
A Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm)
B Clearance to window or door that may be opened 36 inches (91 cm) 12 inches (30 cm)
C Clearance to permanently closed window * *
D
Vercal clearance to venlated sot, located above the terminal within
a horizontal distance of 2 feet (61 cm) from the center line of the
terminal
* *
E Clearance to unvenlated sot * *
F Clearance to outside corner * *
G Clearance to inside corner * *
H
Clearance to each side of center line extended above meter/regulator
assembly
3 feet (91 cm) within a height 15
feet (4.5 m) above the meter/
regulator assembly
*
I Clearance to service regulator vent outlet 36 inches (91 cm) *
J
Clearance to nonmechanical air supply inlet to building or the
combuson air inlet to any other appliance
36 inches (91 cm) 12 inches (30 cm)
K Clearance to a mechanical air supply inlet 6 feet (1.83 m)
3 feet (91 cm) above if within 10
feet (3 m) horizontally
L
Clearance above paved sidewalk or paved driveway located on public
property
7 feet (2.13 m) *
M Clearance under veranda, porch, deck, or balcony 12 inches (30 cm) *
Direct Vent Terminal Clearances (Indoor Units)
8 KCM Series Manual
Other Than Direct Vent Terminal Clearances (Outdoor Units)
INSIDE
CORNER DETAIL
FIXED
CLOSED
OPERABLE
FIXED
CLOSED
OPERABLE
B
B
B
A
J
B
M
C
F
B
B
E
D
L
G
A
H
K
I
[1] A vent shall not terminate directly above a sidewalk or paved driveway
that is located between two single family dwellings and serves both
dwellings.
[2] Permied only if veranda, porch, deck, or balcony is fully open on a
minimum of two sides beneath the oor.
For clearances not specied in ANSI Z223.1/NFPA 54, clearances are in
accordance with local installaon codes and the requirements of the gas
supplier.
Clearance to opposite wall is 24 inches (60 cm).
X
V
AIR SUPPLY INLET
VENT TERMINAL
AREA WHERE TERMINAL
IS NOT PERMITTTED






A Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm)
B Clearance to window or door that may be opened
6 in (15 cm) for appliances ≤ 10,000 Btuh (3
kW), 12 in (30 cm) for appliances > 10,000
Btuh (3 kW) and ≤ 100,000 Btuh (30 kW), 36 in
(91 cm) for appliances >100,000 Btuh (30 kW)
4  (1.2 m) below or to side of opening;
1  (300 mm) above opening
C Clearance to permanently closed window * *
D
Vercal clearance to venlated sot, located above the terminal within a
horizontal distance of 2 feet (61 cm) from the center line of the terminal
* *
E Clearance to unvenlated sot * *
F Clearance to outside corner * *
G Clearance to inside corner * *
H
Clearance to each side of center line extended above meter/regulator
assembly
3 feet (91 cm) within a height 15 feet (4.5 m)
above the meter/regulator assembly
*
I Clearance to service regulator vent outlet 36 inches (91 cm) *
J
Clearance to non-mechanical air supply inlet to building or the combuson
air inlet to any other appliance
6 in (15 cm) for appliances ≤ 10,000 Btuh (3
kW), 12 in (30 cm) for appliances > 10,000
Btuh (3 kW) and ≤ 100,000 Btuh (30 kW), 36 in
(91 cm) for appliances >100,000 Btuh (30 kW)
4  (1.2 m) below or to side of opening;
1  (300 mm) above opening
K Clearance to a mechanical air supply inlet 6 feet (1.83 m)
3 feet (91 cm) above if within 10 feet (3
m) horizontally
L
Clearance above paved sidewalk or paved driveway located on public
property
7 feet (2.13 m) *
M Clearance under veranda, porch, deck, or balcony 12 inches (30 cm) *
Clearance in
Ref. A also
applies to
ancipated
snow line
KCM Series Manual 9
Addional clearances
Check to determine whether local codes supersede
these clearances.
Avoid terminaon locaons near a dryer vent.
Avoid terminaon locaons near commercial
cooking exhaust.
Avoid terminaon locaons near any air inlets.
You must install a vent terminaon at least 12
inches above the ground or ancipated snow
level.
(0.30 m) between
terminals at same
level
(1.52 m)
vercally
between
terminals
60"
V
V
(1.52 m)
between
terminals at
dierent levels
24"
V
(0.61 m) to wall or parapet
12"
V V
V
60"
V
RUS65e, RUS75e
RUCS65i, RUCS75i
The vent for this appliance shall not terminate
Over public walkways; or
Near sot vents or crawl space vents or other
area where condensate or vapor could create a
nuisance or hazard or cause property damage; or
Where condensate or vapor could cause damage
or could be detrimental to the operaon of
regulators, relief valves, or other equipment.
for locang vent
terminaon under a sot (venlated or unvenlated
or eave vent; or to a deck or porch)
Do not install vent terminaon under a sot vent
such that exhaust can enter the sot vent
Install vent terminaon such that exhaust and rising moisture
will not collect under eaves. Discoloraon to the exterior of
the building could occur if installed too close.
Do not install the vent terminaon too close under the sot
where it could present recirculaon of exhaust gases back
into the combuson air intake part of the terminaon.
2"
12 "
60"
36"
(0.91 m) to
venlated or
unvenlated sot
or eve vent; or to a
deck or porch
(1.52 m) vercally
between terminals
(50 mm) between
terminals at same level
(0.30 m) to an
inside corner
(0.30 m) between
terminals at same
level
(0.30 m ) to
an inside
corner
10 KCM Series Manual
Unit clearances





-


 6 * (152) 2 *(51)
 0 (zero) 0 (zero)
 6 (152) 6 (152)
 2 (51) 1/2 (13)
 12 (305) 12 (305)

0 (zero) 0 (zero)
* 0 inches from vent components and condensate drain
line.
The clearance for servicing is 24 inches in front of the
water heater.
For closet installaon, clearance is 6 inches (152 mm from
the front of the water heater.




-


 12 (305) 2 (51)
 0 (zero) 0 (zero)
 24 (610) 0 (zero)
 24 (610) 24 (610)
 6 (152) 1/8 (3.2)
 12 (305) 2 (51)
The clearance for servicing is 24 inches in front of the
water heater.
Freeze Protecon
Make sure that in case of freezing weather the water
heater and its water lines are protected to prevent
freezing. Damage due to freezing is not covered by
the warranty.
With electrical power and gas supplied, the water
heater will not freeze when the outside air
temperature is as cold as –22°F (-30°C) for indoor
models or is as cold as –4°F (-20°C) for outdoor
models, when protected from direct wind exposure.
Because of the “wind-chill” eect, any wind or
circulaon of the air on the unit will reduce its ability
to protect itself from freezing.
In the event of a power failure and/or gas
interrupon at temperatures below freezing the
water heater should be drained of all water to
prevent freezing damage. In addion, drain the
condensate trap and drain line.
Loss of freeze protecon may result in water damage
from a burst heat exchanger or water lines.
The unit may be drained manually. However, it is
highly recommended to:
drain down solenoid valves be purchased and
installed that will automacally drain the unit if
power is lost. These are available in a kit,
104000059. (The condensate trap is not aected
by the auto drain down solenoid valves and will
have to be manually drained.)
a surge protector with terminals be purchased
and installed which allows the solenoid valves to
operate if the unit is disabled due to a diagnosc
code. This is available as 104000057.
In addion, the solenoid valves should be connected
electrically to a surge protector with terminals. This
allows the solenoid valves to operate if the water
heater is disabled due to a diagnosc code.
The freeze protecon features of the water heater
will not prevent the external piping from freezing. It
is recommended that hot and cold water pipes be
insulated. Pipe cover enclosures may be packed with
insulaon for added freeze protecon.
It is recommended that the condensate trap drain line
be insulated. A frozen condensate trap results in a
diagnosc code 25.
KCM Series Manual 11

wall installaon
brackets
1. Idenfy the installaon locaon and conrm that
the installaon will meet all required clearances.
2. Securely aach the water heater to the wall
using any of the holes in the wall installaon
brackets which are at the top and boom of the
water heater. Ensure that the aachment
strength is sucient to support the weight of the
water heater. Refer to the weight of the water
heater in the Specicaons secon of this
manual.
Use a leveling tool to ensure that the water
heater is level. Proper operaon requires that
the water heater be level.


The water heater is not exposed to corrosive
compounds in the air.
The water heater locaon complies with all
required clearances.
For indoor models, the planned venng will not
exceed the maximum length for the number of
elbows used.
The planned venng terminaon/air intake
locaon meets all required clearances.
Indoor air is not being used for combuson.
The water supply does not contain chemicals or
exceed total hardness that will damage the heat
exchanger.
A standard 3 prong 120 VAC, 60 Hz properly
grounded wall outlet (for indoor models) or other
120 VAC, 60 Hz source is available.
The installaon must conform with local codes or,
in the absence of local codes, with the Naonal
Fuel Gas Code, ANSI Z223.1/NFPA 54, or the
Natural Gas and Propane Installaon Code, CSA
B149.1. If installed in a manufactured home, the
installaon must conform with the Manufactured
Home Construcon and Safety Standard, Title 24
CFR, Part 3280 and/or CAN/SCA Z240 MH Series,
Mobile Homes.




Slide the plasc trim pieces on each side of the water
heater to expose the screws.
Remove the 4 screws and pull o the front panel.
NOTICE
The water heater must be installed in an upright
posion. Do not install upside down or on its side.
12 KCM Series Manual

Install the correct venng for your model according to the venng manufacturer’s instrucons and the guidelines
below. Refer to the vent manufacturer’s technical literature for specic part numbers and instrucons.
   
Ubbink Rolux 184162PP 223176PP, 223177PP
Centrotherm InnoFlue ICRT3539 ISELL0387UV
Heat-Fab Saf-T Vent
Saf-T Vent CI Plus Wall
Terminaon
Saf-T Vent CI Plus Rain Cap
Metal-Fab Corr/Guard 3CGRVDK 3CGRVT
Ipex Concentric Kit
3”- 196006 /197009
4”-196021 /197021
3”- 196006 / 197009
4”-196021 / 197021
Ipex Low Prole Terminaon Kit
3”- 196985
4”- 196986
Various
Manufacturers
Schedule 40 PVC DWV Solid
Core Pipe (or approved equal)
CPVC schedule 40
Reference “Approved PVC/CPVC
Vent Conguraons” Table
Reference “Approved PVC/
CPVC Vent Conguraons”
Table



  
Ubbink
Rolux Condensing
Vent System
800-621-9419 678-829-1666 www.rinnai.us
Centrotherm
InnoFlue Vent System (single
wall SW, 3 inch diameter)
877-434-3432 518-618-3166
info@centrotherm.us.com
www.centrotherm.us.com
Heat-Fab Saf-T Vent SC system 800-772-0739 413-863-4803
custsvc@heat-fab.com,
www.heaab.com
Metal-Fab
Corr/Guard Vent/Air Intake
System
800-835-2830 316-943-2717
www.metal-fabinc.com
Ipex
Concentric Kit / Low Prole
Terminaon Kit
U.S. - 800-463-9572
CA. - 866-473-9462
www.ipexamerica.com
www.ipexinc.com
Various
Manufacturers
Schedule 40 PVC DWV Solid Core
Pipe (or approved equal)
CPVC schedule 40
Approved Vent Manufacturers
Approved Vent Products

KCM Series Manual 13
Venng Guidelines

Do not use cellular core PVC/CPVC.
Do not use Radel, ABS, or galvanized material to
vent this appliance.
Do not cover non-metallic vent pipe and ngs
with thermal insulaon.
Do not combine vent components from dierent
manufacturers.
Vent diameter must not be reduced.
Do not connect the venng system with an
exisng vent or chimney.
Do not common vent.

This water heater is a direct vent water heater and
therefore is cered and listed with the vent
system. You must use vent components that are
cered and listed with the water heater model.
The vent system must vent directly to the outside
of the building and use outside air for combuson.
Avoid dips or sags in horizontal vent runs by
installing supports per the vent manufacturer’s
instrucons.
Support horizontal vent runs every four feet and
all vercal vent runs every six feet or in
accordance with local codes.
Venng should be as direct as possible with a
minimum number of pipe ngs.
Vent connecons must be rmly pressed together
so that the gaskets form an air ght seal.
The vent piece connected to the water heater
must be secured with one self-tapping screw.

Refer to the instrucons of the vent system
manufacturer for component assembly
instrucons.
If the vent system is to be enclosed, it is suggested
that the design of the enclosure permit inspecon
of the vent system. The design of such enclosure
shall be deemed acceptable by the installer or the
local inspector.

If it becomes necessary to access an enclosed vent
system for service or repairs, Rinnai is not responsible
for any costs or dicules in accessing the vent
system. The warranty does not cover obtaining
access to a vent system in an enclosed environment.

 
Concentric OFF
Twin Pipe ON

Prior to the installaon of the vent system, the dip
switches on the PCB board must be properly set for
the venng conguraon selected for the applicaon.
(Unit comes defaulted for concentric applicaons)

-
-


14 KCM Series Manual

Prior to the installaon of the vent system, the
unit must be properly adjusted for the venng
conguraon selected for the applicaon.
Any issues resulng from improper installaon
will not be covered by warranty.
Ducted outside air is mandatory for all twin pipe
conguraons.
NOTICE
Exhaust Adapter
Ring to be removed
and discarded for
concentric vent
conguraon
Concentric Vent Conguraon
(Same procedure to be used for Twin Pipe with
Centrotherm Adapter Conguraon)
Removal of Exhaust Adapter Ring
1. Remove fastener from concentric ue
connecon.
2. Remove exhaust adapter ring.
3. Install the concentric vent. Ensure it is properly
seated.
4. Secure the vent pipe to the unit with a screw
KCM Series Manual 15
Intake Cap to be removed and discarded
for twin pipe PVC/CPVC conguraon.

Removal of Intake Cap
1. Remove the fastener from intake connecon.
2. Remove the intake cap.
Twin Pipe PVC/CPVC Conguraon
(3”or 4”)
3. Install the intake pipe. Ensure it is properly
seated.
4. Secure the intake pipe to the unit with the
supplied screw (in the carton box).
5. Install the exhaust pipe. Ensure it is properly
seated.
6. Secure the exhaust pipe to the unit with the
supplied screw (in the carton box).

apply PVC glues, solvents, or cleaners
to the water heaters intake or exhaust gasket
connecons. Failure to correctly assemble the
components according to these instrucons
may result in property damage, personal injury,
or death.
Intake Gasket Connecon
Exhaust Gasket Connecon
16 KCM Series Manual
Maximum vent length

1. Determine the number of 90 degree elbows in
the vent system. (Two 45 degree elbows count as
one 90 degree elbow.)
2. Refer to the table to nd the maximum vent
length based on the number of elbows.
3. Adjust SW1 in DIPSW 1 (tan switches) if required
by the applicable note.
If the length is greater than 21  (6.4 m) then
move SW1 to OFF.
If the length is greater than 15  (4.6 m) then
move SW1 to OFF.
If the length is greater than 9  (2.7 m) then move
SW1 to OFF.
Move SW1 to OFF.
Example: If you have one elbow then your maximum
vent length is 35 feet (10.7 m). If your
actual length is greater than 15  (4.6 m)
then move SW1 in DIPSW 1 to OFF.
If you have a longer vent length (see number 3
regarding max. vent length), SW1 in DIPSW 1 is
required to be in the OFF posion. This ensures the
water heater will run properly. Blocked ue
diagnosc codes and shutdowns may result if SW1 in
DIPSW 1 is not in the correct posion.


(Intake is the short UV protected 90° elbow)








If length is greater
than:
0 41  (12.50 m)
18  (5.49 m) move
SW1 to OFF
1 26  (7.93 m)
3  (0.91 m) move SW1
to OFF
2 11  (3.35 m)
move SW1 to OFF for
any length








If length is greater
than:
0 41  (12.50 m) 21  (6.40 m) move
1 35  (10.67 m) 15  (4.57 m) move
2 29  (8.84 m) 9  (2.74 m) move
3 23  (7.01m) 3  (0.91 m) move
4 17  (5.18 m)
move SW1 to OFF
for any length
5 11  (3.35 m)
6 5  (1.52 m)

(Intake is the long UV protected 90° elbow)

InnoFlue Vent System (single wall SW, 3 inch diameter)

(90° elbow is equivalent to 6 feet; 45° elbow is equivalent to 3 feet.)




0 41 (12.5)
1
1 35 (10.7)
2
2 29 (8.8)
3
3 23 (7.0)
4
4 17 (5.2)
4
5 11 (3.4)
4
6 5 (1.5)
4
KCM Series Manual 17
Maximum vent length

(90° elbow is equivalent to 5 feet; 45° elbow is equivalent to 2.5 feet.)




0 41 (12.5)**
1 36 (11.0) **
2 31 (9.4) **
3 26 (7.9) **
4 21 (6.4) **
5 16 (4.9) **
6 11 (3.4) **
**SW 1 in DIPSW 1 is “OFF” for lengths greater than
or equal to 21 feet.

(90° elbow is equivalent to 5 feet; 45° elbow is equivalent to 2.5 feet.)




0 100 (30.5)**
1 95 (29.0) **
2 90 (27.4) **
3 85 (25.9) **
4 80 (24.4) **
5 75 (22.9) **
6 70 (21.3) **

(See Twin Pipe PVC/CPVC Vent Installaon secon for
more informaon regarding equivalent vent length
calculaons.)
18 KCM Series Manual
Flue Installaon with Concentric Venng (indoor models only)
Install the venng terminaon according to the diagrams and instrucons below.
Secure the first vent component to the water heater
with one self-tapping screw at the hole.


Slope the venting 1/4” per foot toward the
appliance according to the vent manufacturers
installation instructions.
Dispose of condensate per local codes.
Securing Screw
Slope the venting 1/4” per foot toward the
appliance according to the vent manufacturers
installation instructions.
Dispose of condensate per local codes.
KCM Series Manual 19
Comply with the exhaust clearances found in this Rinnai Installaon and Operaon Manual.
Only one appliance can be aached to the vent system.
Install the system according to the Centrotherm installaon instrucons included with the vent system.
The vent terminaon and air intake must be in the same pressure zone.
Do not exceed the maximum straight vent length with number of elbows as shown in the tables in the
following secon.
Maintain the clearances shown in the gures below.

The following vent materials are for use with this appliance:
Cellular core PVC/CPVC
Radel, ABS, and/or Galvanized ducts.
Failure to use approved vent materials can result in property damage, personal injury, or death.

Flue Installaon with Centrotherm Venng (indoor models only)
Install the venng terminaon according to the diagrams and instrucons below.

11
5”
Intake
Oponal
Vent
Slope horizontal exhaust run towards the water heater 1/4” per foot. slope combuson air pipe towards unit. Be
sure to dispose of condensate per local codes.
20 KCM Series Manual
Installaons must comply with local requirements and with the Naonal Fuel Gas Code, ANSI Z223.1/NFPA 54 for U.S.
installaons or CSA B149.1 for Canadian installaons.  use cellular core PVC, CPVC, or Radel based pipe materials
for the exhaust vent. Vents  be of solid core pipes ONLY.

Use only the materials listed in this secon for vent, air intake pipe, and ngs (See vent and air piping materials table).
Failure to comply with this warning could result in property damage, personal injury, or death.

Twin Pipe PVC/CPVC Vent Installaon
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132

Rinnai RUCS65i series Guide d'installation

Catégorie
Chauffe-eau
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues