LG Electronics DLE2701V Manuel utilisateur

Protocol P154

Sanitization Performance of Residential

Clothes dryer

Ejecucion de Saneamiento en la zona

residencial Secadoras

Niveau de sanitisation des séche-linge

résidentiels

P/No. 3828EL3010Y

Before beginning installation, read these

instructions carefully. This will simplify installation

and ensure that the dryer is installed correctly and

safely. Leave these instructions near the dryer

after installation for future reference.

Antes de comenzar la instalación, lea atentamente

estas instrucciones. Esto simpliﬁcará la instalación

y asegurará que la secadora está instalada

en forma correcta y segura. Conserve estas

instrucciones cerca de la secadora luego de la

instalación para futuras consultas.

To contact LG Electronics, 24 hours a day,

7 days a week:

1-800-243-0000

Or visit us on the Web at: us.lge.com

Número telefónico de LG Electronics, las 24

horas del día, 7 días a la semana:

1-800-243-0000

O visítenos en la Web en: us.lge.com

To contact LG Electronics, 24 hours a day,

7 days a week :

1-888-LGCANADA

Or visit us on the Web at : ca.lge.com

Pour contacter LG Electronics, 24 heures

Par jour, 7 jours par semaine :

1-888-LGCANADA

Ou visitez notre site Web a l’addresse :

ca.lge.com

C

E

R

T

I

F

I

E

D

E

S

I

G

N

DLE2701W

DLE2701V

DLG2702W

DLG2702V

Avant de commencer à installer votre sécheuse, lisez

attentivement ces instructions. Cela simpliﬁera votre

installation et assurera que la sécheuse est installée

correctement et en toute sécurité. Conservez ces

instructions à proximité de la sécheuse après son

installation, pour référence future.

Congratulations on your purchase

and welcome to the LG family. Your

new LG Dryer combines the most

advanced drying sensor technology

with simple operation and high

efficiency. By following the

operating and care instructions

in this manual, your dryer will

provide you with many years of

reliable service.

THANK YOU!

INSTALLATION INSTRUCTIONS

IMPORTANT: Read all installation instructions

completely before installing and operating your

dryer! ................................................................... 10

Choose the Proper Location ................................ 10

Clearances ........................................................... 10

Installation With Optional Pedestal Base or

Stacking Kit .......................................................... 11

Optional Accessories ......................................... 11

Leveling the Dryer ................................................ 12

Reversing the Door Swing .................................... 12

Changing the Dryer Vent Location ....................... 13

Venting the Dryer ............................................ 14, 15

Connecting Gas Dryers .................................. 16, 17

Connecting Electric Dryers ............................. 18–22

Special Requirements for Manufactured

or Mobile Homes .................................................. 23

Final Installation Check ....................................... 23

Flow Check (Duct condition test) ......................... 24

HOW TO USE

Sorting Loads ....................................................... 2 5

Loading the Dryer ................................................. 25

Check the Lint Filter Before Every Load ............... 25

Control Panel Features ......................................... 26

Cycle Guide .................................................... 27, 28

The Display ........................................................... 28

Operating the Dryer .............................................. 29

Cycle Setting Buttons .......................................... 30

Cycle Option Buttons .......................................... 31

Special Functions ................................................. 32

Custom Program .................................................. 32

TROUBLESHOOTING

Before Calling for Service ............................... 34–35

USER MAINTENANCE INSTRUCTIONS

Regular Cleaning .................................................. 33

IMPORTANT SAFETY INSTRUCTIONS

What to Do if You Smell Gas .................................. 3

Basic Safety Precautions ....................................... 4

California safe drinking water and toxic

enforcement act .................................................... 4

Grounding Instructions ...........................................5

Safety Instructions for Installation ......................5, 6

Safety Instructions for Connecting Electricity .......7

PARTS AND FEATURES

Special Features ..................................................... 8

Key Parts and Components ................................... 9

OPTIONAL ACCESSORIES/

SPECIFICATIONS

Optional Accessories ........................................... 36

Pedestal Installation ....................................... 37, 38

Stacking Kit Installation .................................. 39, 40

Key Dimensions and Speciﬁcations ..................... 40

WARRANTY ............................................. 41, 42

2

1. Do not try to light a match or cigarette,

or turn on any gas or electrical

appliance.

2. Do not touch any electrical switches.

Do not use any phone in your building.

3. Clear the room, building, or area of all

occupants.

4. Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions carefully.

5. If you cannot reach your gas

supplier, call the ﬁre department.

WHAT TO DO IF YOU SMELL GAS:

READ ALL INSTRUCTIONS BEFORE USE

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read

and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions.

wWARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of

injury, and tell you what can happen if the instructions are not followed.

•Donotinstallaclothesdryerwith

ﬂexible plastic venting materials. If

ﬂexible metal (foil type) duct is in-

stalled, it must be of a speciﬁc type

identiﬁed by the appliance manufac-

turer as suitable for use with clothes

dryers. Flexible venting materials are

known to collapse, be easily crushed,

and trap lint. These conditions will

obstruct clothes dryer airﬂow and

increase the risk of ﬁre.

•Donotstoreorusegasolineorother

ﬂammable vapors and liquids in the

vicinity of this appliance or any other

appliances.

•Installationandservicemustbe

performed by a qualiﬁed installer,

service agency, or the gas supplier.

•Installtheclothesdryeraccordingto

the manufacturer’s instructions and

local codes.

•Savetheseinstructions.

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

3

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT

This act requires the governor of California to publish a list of substances known to the state to cause

cancer, birth defects, or other reproductive harm and requires businesses to warn customers of potential

exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be

minimized further by properly venting the dryer to the outdoors.

BASIC SAFETY PRECAUTIONS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Readallinstructionsbeforeusingthedryer.

•Beforeuse,thedryermustbeproperlyinstalled

as described in this manual.

•Donotplaceitemsexposedtocookingoilsin

your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that

could cause a load to catch ﬁre.

•Donotdryarticlesthathavebeenpreviously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

ﬂammable or explosive substances as they give

off vapors that could ignite or explode.

•Donotreachintothedryerifthedrumorany

other part is moving.

•Donotrepairorreplaceanypartofthedryer

or attempt any servicing unless speciﬁcally

recommended in this Use and Care Guide or

in published user-repair instructions that you

understand and have the skills to carry out.

•Donottamperwithcontrols.

•Beforethedryerisremovedfromserviceor

discarded, remove the door to the drying

compartment.

•Donotallowchildrentoplayonorinthedryer.

Close supervision of children is necessary when

the dryer is used near children.

•Donotusefabricsoftenersorproductsto

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

•Donotuseheattodryarticlescontaining

foam rubber or similarly textured rubber-like

materials.

•Keepareaaroundtheexhaustopeningand

adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

•Theinteriorofthedryerandexhaustvent

should be cleaned periodically by qualiﬁed

service personnel.

•Donotinstallorstorethedryerwhereitwillbe

exposed to the weather.

•Alwayschecktheinsideofthedryerforforeign

objects.

•Cleanlintscreenbeforeoraftereachload.

4

5

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event

of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing

a path of least resistance for electric current.

This appliance must be equipped with a cord

having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into

an appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances.

wWARNING — Improper

connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualiﬁed electrician or service

person if you are in doubt as to whether the

appliance is properly grounded.

Do not modify the plug provided with the

appliance. If it will not ﬁt the outlet, have a proper

outlet installed by a qualiﬁed electrician.

This appliance must be connected to a grounded

metal, permanent wiring system or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the appliance.

Electrical shock can result if the dryer is not

properly grounded.

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

•Properly ground dryer to conform with all

governing codes and ordinances. Follow

details in the installation instructions. Electrical

shock can result if the dryer is not properly

grounded.

•Before use, the dryer must be properly

installed as described in this manual.

Electrical shock can result if the dryer is not

properly grounded.

•Install and store the dryer where it will not be

exposed to temperatures below freezing or

exposed to the weather.

•All repairs and servicing must be performed

by an authorized servicer unless speciﬁcally

recommended in this Owner’s Guide. Use

only authorized factory parts. Failure to follow

this warning can cause serious injury, ﬁre,

electrical shock, or death.

•To reduce the risk of electric shock, do not

install the dryer in humid spaces. Failure to

follow this warning can cause serious injury, ﬁre,

electrical shock, or death.

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Connect to a properly rated, protected,

and sized power circuit to avoid electrical

overload. Improper power circuit can melt,

creating electrical shock and/or ﬁre hazard.

•Remove all packing items and dispose of all

shipping materials properly. Failure to do so

can result in death, explosion, ﬁre, or burns.

•Place dryer at least 18 in. above the ﬂoor

for a garage installation. Failure to do so can

result in death, explosion, ﬁre, or burns.

•Keep all packaging from children. Packaging

material can be dangerous for children. There is

a risk of suffocation.

•Do not install nearby heat item. Such as

stove, cooking oven. Failure to do so can cause

deform, smoke and ﬁre.

•Do not place candle and cigarettes on top of

the product. Failure to do so can cause deform,

smoke and ﬁre.

•Remove all protective vinyl ﬁlm from the

product. Failure to do so can cause deform,

smoke and ﬁre.

6

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

Exhaust/Ducting:

•GasdryersMUSTbeexhaustedtothe

outside. Failure to follow these instructions

can result in ﬁre or death.

•The dryer exhaust system must be exhausted

to the outside of the dwelling. If the dryer is

not exhausted outdoors, some ﬁne lint and

large amounts of moisture will be expelled

into the laundry area. An accumulation of

lint in any area of the home can create a health

and ﬁre hazard.

•Use only rigid metal or ﬂexible metal 4-in.

diameter ductwork inside the dryer cabinet

or for exhausting to the outside. Use of

plastic or other combustible ductwork can

cause a ﬁre. Punctured ductwork can cause

a ﬁre if it collapses or becomes otherwise

restricted in use or during installation.

•Ductwork is not provided with the dryer, and

you should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the dryer

is not in use. Failure to follow these instructions

can result in ﬁre or death.

•The exhaust duct must be 4 in. (10.2 cm) in

diameter with no obstructions. The exhaust

duct should be kept as short as possible.

Make sure to clean any old ducts before

installing your new dryer. Failure to follow

these instructions can result in ﬁre or death.

•Rigid or semi rigid metal ducting is

recommended for use between the

dryer and the wall. In special installations

when it is impossible to make a connection

with the above recommendations, a UL-

listed ﬂexible metal transition duct may be

used between the dryer and wall connection

only. The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁre or death.

•DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁciency

of the exhaust system. Secure all joints with

duct tape. For complete details, follow the

Installation Instructions. Failure to follow these

instructions can result in ﬁre or death.

SAVE THESE INSTRUCTIONS

7

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

•Do not, under any circumstances, cut or

remove the ground prong from the power

cord. To prevent personal injury or damage to

the dryer, the electrical power cord must be

plugged into a properly grounded outlet.

•For personal safety, this dryer must be

properly grounded. Failure to do so can result

in electrical shock or injury.

•Refer to the installation instructions in this

manual for speciﬁc electrical requirements

for your model. Failure to follow these

instructions can create an electrical shock

hazard and/or a ﬁre hazard.

•This dryer must be plugged into a properly

grounded outlet. Electrical shock can result if

the dryer is not properly grounded. Have the

wall outlet and circuit checked by a qualiﬁed

electrician to make sure the outlet is properly

grounded. Failure to follow these instructions

can create an electrical shock hazard and/or a

ﬁre hazard.

•The dryer should always be plugged into

its own individual electrical outlet which

has a voltage rating that matches the rating

plate. This provides the best performance

and also prevents overloading house wiring

circuits which could cause a ﬁre hazard from

overheated wires.

•Never unplug your dryer by pulling on the

power cord. Always grip plug ﬁrmly and pull

straight out from the outlet. The power cord

can be damaged, resulting in a risk of ﬁre and

electrical shock.

•Repair or replace immediately all power

cords that have become frayed or otherwise

damaged. Do not use a cord that shows

cracks or abrasion damage along its length

or at either end. The power cord can melt,

creating electrical shock and/or ﬁre hazard.

•When installing or moving the dryer, be

careful not to pinch, crush, or damage

the power cord. This will prevent injury and

prevent damage to the dryer from ﬁre and

electrical shock.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

SPECIAL FEATURES

1

EASY-TO-USE CONTROL PANEL

Rotate the Cycle Selector Knob to select the

desired dry cycle. Add cycle options or adjust

settings with the touch of a button.

2

3

EASY-ACCESS REVERSIBLE DOOR

Wide-opening door provides easy access for

loading and unloading. Door swing can be

reversed to adjust for installation location.

ULTRA-CAPACITY STAINLESS STEEL DRUM

WITH DRUM LIGHT

The ultra-large stainless steel drum offers

superior durability. The drum is equipped with a

yellow light that illuminates when the dryer door

is open and turns off when the door is closed.

4

1

2

3

4

FLOW SENSE™ DUCT BLOCKAGE SENSING

SYSTEM INDICATOR

The FLOW SENSE™ duct blockage sensing

system detects and alerts you to blockages in

the ductwork that reduce exhaust flow from the

dryer. This improve operating efficiency and help

minimize service calls, saving you money.

8

1

2

LEVELING FEET

Four leveling feet (two in the front, and two in the back)

adjust to improve dryer stability on uneven floors.

FRONT-MOUNT LINT FILTER

Front-mounted lint filter allows for easy access

and cleaning after every load.

Terminal Block

Access Panel

(Electric Models)

Rear of Dryer

Power Cord Location

(Gas Models)

Gas

Connection

Location

(Gas Models)

Exhaust Duct

Outlet

KEY PARTS AND COMPONENTS

In addition to the special features and

components outlined in the Special Features

section, there are several other important

components that are referenced in this manual.

DRYING RACK

Use the drying rack with the RACK DRY cycle

option. The drying rack allows items, such as

sweaters, delicates, and gym shoes, to be placed

in a flat position for drying.

3

Included Accessories

Drying Rack

3

2

1

9

CHOOSE THE PROPER LOCATION

•Storeandinstallthedryerwhereitwillnotbe

exposed to temperatures below freezing or

exposed to outdoor weather conditions.

•Choosealocationwithasolid,leveloor.

•Ifthedryerisbeinginstalledinagarage,

place the dryer at least 18 in. (46 cm) above

the ﬂoor.

CLEARANCES

•Mostinstallationsrequireaminimum5½in.

(14 cm) clearance behind the dryer for the

exhaust ducting.

•Allowminimumclearancesofatleast1in.

(2.5 cm) on the sides and back to minimize

vibration and noise.

•Allowingadditionalclearanceforinstallationand

servicing is recommended.

•Besuretoallowforwall,door,oroormoldings

that may increase the required clearances.

•Allowatleast24in.(61cm)infrontofthedryer

to open the door.

IMPORTANT: Read all installation instructions completely before

installing and operating your dryer!

It is important that you review this entire manual before installing and using your dryer. Detailed instructions

concerning electrical connections, gas connections, and exhaust requirements are provided on the

following pages.

•Properlygrounddryertoconformwithall

governing codes and ordinances.

•Toreducetheriskofelectricshock,donot

install the dryer in damp or wet locations.

•Ifyouareinstallingyourdryerinamanufactured

or mobile home, please refer to the section

Special Requirements for Manufactured or

Mobile Homes.

Additional Instructions for closet installations:

•Theclosetdoormustallowforsufcientairow.

Refer to the diagram above for minimum vent

opening requirements. A louvered door is also

acceptable.

•Makesurethatthereisatleast18in.(46cm)of

clearance above the dryer.

Closet Door Vent

Requirements

4”

(10 cm)

30”

(76.1 cm)

51”

(130 cm)

18”

(45.7 cm)

22.5”

(57.2 cm)

4”

(10 cm)

10

INSTALLATION WITH OPTIONAL

PEDESTAL BASE OR STACKING KIT

IMPORTANT: If you are installing your dryer

using an optional pedestal base or stacking

kit, please refer to Optional Accessories in this

manual or to the instructions for your pedestal

or stacking kit before proceeding with the

installation.

Required Dimensions for Installation

With Pedestal

Required Dimensions for Installation

WithStackingKit

OPTIONAL ACCESSORIES

For these and other LG products, contact your local LG dealer, or visit our Web site at us.lge.com.

Pedestal (sold separately)

Stacking Kit (sold separately)

30”

(76.2 cm)

4”

(10 cm)

77

1

⁄

2

”

(190.5 cm)

1”

(2.5 cm)

1”

(2.5 cm)

27”

(68.6 cm)

11

1 2

Hinge

Screws

Door

Latch

Latch Screws

Hinge

Screws

Latch

Screws

LEVELING THE DRYER

Use an adjustable wrench to turn the leveling

feet. Turn clockwise to raise the dryer or

counterclockwise to lower it. Raise or lower

the leveling feet until dryer is level from

side to side and front to back.

Make sure that all 4 leveling feet are in firm

contact with the floor.

REVERSING THE DOOR SWING

The swing of the dryer door can be reversed to fit your installation location.

Open the dryer door. Using a Phillips

screwdriver, remove the 4 screws that secure

the door hinge to the dryer door opening.

Remove the 6 screws from the latch side of the

dryer door opening, and remove the door latch.

Turn the door around so the hinge is

reversed, and reattach the door using the

4 screws previously removed. Reinstall the

door latch and the 6 screws.

Test the door swing to make sure the door

moves freely and latches securely.

2

Position the dryer in the final location. Place

a level across the top of the dryer.

1

Level

Leveling Feet

•Allfourleveling feet must restsolidlyonthe

floor. Gently push on the top corners of the

dryer to make sure that the dryer does not

rock from corner to corner.

If you are installing the dryer on the optional

pedestal, you must use the leveling feet on the

pedestal to level the dryer. The dryer leveling feet

should be fully retracted.

To ensure that the dryer provides optimal drying

performance, it must be level. To minimize

vibration, noise, and unwanted movement, the

floor must be a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as

necessary to level the dryer. Extending the

leveling feet more than necessary can cause

the dryer to vibrate.

12

WARNING

•Wearglovesduringinstallation.

•Failuretofollowtheseinstructionscanresultininjury.

w

CHANGING THE DRYER VENT LOCATION

Your new dryer is shipped to vent to the rear.

It can also be configured to vent to the bottom

or side (right-side venting is not available on

gas models).

An adapter kit, part number 383EEL9001B,

may be purchased from your LG retailer. This

kit contains the necessary duct components

to change the dryer vent location.

Remove the rear exhaust duct retaining

screw. Pull out the exhaust duct.

1

Rear

Exhaust Duct

Retaining

Screw

Preassemble a 4-in. (10 cm) elbow to the next 4-in. (10 cm)

duct section, and secure all joints with duct tape. Be sure

that the male end of the elbow faces AWAY from the dryer.

Insert the elbow/duct assembly through the side opening

and press it onto the adapter duct. Secure in place with

duct tape.

Besurethatthemaleendoftheductprotrudes1½in.(3.8

cm) to connect the remaining ductwork.

Attach cover plate to the back of the dryer with included

screw.

1

/2"

(3.8 cm)

3

Elbow

Cover

Plate

Insert the 4-in. (10 cm) elbow through the

rear opening and press it onto the adapter

duct. Be sure that the male end of the elbow

faces down through hole in the bottom of the

dryer. Secure in place with duct tape.

Attach the cover plate to the back of the

dryer with included screw.

3

Elbow

Cover

Plate

Press the tabs on the knockout and carefully remove the

knockout for the desired vent opening (right-side venting

is not available on gas models). Press the adapter duct

onto the blower housing and secure to the base of the

dryer as shown.

2

Knockout

Bracket

Adapter

Duct

OPTION 1: Side Venting

Press the adapter duct onto the blower

housing and secure to the base of the dryer

as shown.

2

Bracket

Adapter

Duct

OPTION 2: Bottom Venting

13

WARNING

w

•Useaheavymetalvent.

•Donotuseplasticorthinfoilduct.

•Cleanoldductsbeforeinstallingthisdryer.

•Wearglovesduringinstallation.

•Failuretofollowtheseinstructionscanresultindeath

or ﬁre.

VENTING THE DRYER

•Do not crush or collapse ductwork. Failure

to follow these instructions can result in ﬁre

or death.

•Do not allow ductwork to rest on or

contact sharp objects. Failure to follow these

instructions can result in ﬁre or death.

•If connecting to existing ductwork, make

sure it is suitable and clean before installing

the dryer. Failure to follow these instructions

can result in ﬁre or death.

•Venting must conform to local building

codes. Failure to follow these instructions can

result in ﬁre or death.

•GasdryersMUSTexhausttotheoutdoors.

Failure to follow these instructions can result

in ﬁre or death.

•Use only 4-in. (10.2 cm) rigid or ﬂexible

metal ductwork inside the dryer cabinet and

for venting outside. Failure to follow these

instructions can result in ﬁre or death.

•To reduce the risk of ﬁre, combustion, or

accumulation of combustible gases, DO

NOT exhaust dryer air into an enclosed and

unventilated area, such as an attic, wall,

ceiling, crawl space, chimney, gas vent, or

concealed space of a building. Failure to

follow these instructions can result in ﬁre

or death.

•To reduce the risk of ﬁre, DO NOT exhaust

the dryer with plastic or thin foil ducting.

Failure to follow these instructions can result

in ﬁre or death.

•The exhaust duct must be 4 in. (10.2 cm) in

diameter with no obstructions. The exhaust

duct should be kept as short as possible.

Make sure to clean any old ducts before

installing your new dryer. Failure to follow

these instructions can result in ﬁre or death.

•Rigid or semirigid metal ducting is

recommended for use between the dryer

and the wall. In special installations when

it is impossible to make a connection with

the above recommendations, a UL-listed

ﬂexible metal transition duct may be used

between the dryer and wall connection only.

The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁre or death.

•DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁciency

oftheexhaustsystem.Securealljoints

with duct tape. Failure to follow these

instructions can result in ﬁre or death.

•To maximize operating results, please

observe the duct length limitations noted in

the chart on page 15. Failure to follow these

instructions can result in ﬁre or death.

•Ductwork is not provided with the dryer.

You should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the

dryer is not in use. Failure to follow these

instructions can result in ﬁre or death.

•The Total length of ﬂexible metal duct shall

not exceed 8 ft.(2.4m)

•In Canada, that only those foil-type ﬂexible

ducts, if any, speciﬁcally identiﬁed for use

with the appliance by the manufacturer

shall be used. In the United States, that only

those foil-type ﬂexible ducts, if any, speciﬁcally

identiﬁed for use with the appliance by the

manufacturer and that comply with the Outline

for Clothes Dryer Transition Duct, Subject

2158A, shall be used.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

14

Routing and Connecting Ductwork

Follow the guidelines below to maximize drying

performance and reduce lint buildup and

condensation in the ductwork.

NOTE: Ductwork and fittings are NOT included

and must be purchased separately.

•Use4-in.(10.2cm)diameterrigidorsemirigid

metal ductwork.

•Theexhaustductrunshouldbeasshortas

possible.

•Useasfewelbowjointsaspossible.

•Themaleendofeachsectionofexhaustduct

must point away from the dryer.

•Useducttapeonallductjoints.

•Insulateductworkthatrunsthroughunheated

areas in order to reduce condensation and lint

buildup on duct surfaces.

IMPORTANT: Failure to exhaust the dryer

correctly will void the dryer’s warranty.

VENTING THE DRYER (cont.)

Correct Venting

Incorrect Venting

NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.

65 ft. (19.8 m)

55 ft. (16.8 m)

47 ft. (13.7 m)

36 ft. (11.0 m)

28 ft. (8.5 m)

55 ft. (16.8 m)

47 ft. (13.7 m)

41 ft. (12.5 m)

30 ft. (9.1 m)

22 ft. (6.7 m)

Ductwork

4"

(10.2 cm)

4"

(10.2 cm)

Recommended

2

1

/2"

(6.35 cm)

Use Only for Short

Run Installations

Wall Cap Type

0

1

2

3

4

0

1

2

3

4

Number of 90° Elbows

Max. Length of 4-In. Dia.

Rigid Metal Duct

15

Electrical Requirements for Gas Models Only

• Do not, under any circumstances, cut or

remove the third (ground) prong from the power

cord. Failure to follow this warning can result in

ﬁre, explosion, or death.

• For personal safety, this dryer must be properly

grounded. Failure to follow this warning can result

in ﬁre, explosion, or death.

• The power cord of this dryer is equipped with

a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock

hazard from this appliance. Failure to follow this

warning can result in ﬁre, explosion, or death.

• This dryer must be plugged into a

120-VAC, 60-Hz. grounded outlet protected by

a 15-ampere fuse or circuit breaker. Failure to

follow this warning can result in ﬁre, explosion,

or death.

• Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility

and obligation to have it replaced with a

properly grounded 3-prong wall outlet. Failure

to follow this warning can result in ﬁre, explosion,

or death.

16

CONNECTING GAS DRYERS

•Gas supply requirements:

As shipped from the factory, this dryer is

conﬁgured for use with natural gas. It can be

converted for use with LP (Liqueﬁed Propane)

gas. Gas pressure must not exceed 13 in.

water column.

•A qualiﬁed service or gas company technician

must connect the dryer to the gas service.

Failure to do so can result in ﬁre, explosion,

or death.

•Isolate the dryer from the gas supply system

by closing its individual manual shutoff valve

during any pressure testing of the gas supply.

Failure to do so can result in ﬁre, explosion,

or death.

•Supplylinerequirements:

Your laundry room must have a rigid gas

supplylinetoyourdryer.IntheUnitedStates,

anindividualmanualshutoffvalveMUSTbe

installed within at least 6 ft. (1.8 m) of the dryer,

in accordance with the National Fuel Gas Code

ANSIZ223.1orCanadiangasinstallationcode

CSAB149.1.A1/8-in.NPTpipeplugmust

be installed. Failure to do so can result in ﬁre,

explosion, or death.

•If using a rigid pipe, the rigid pipe should be

1/2-in.IPS.Ifacceptableunderlocalcodes

and ordinances and when acceptable to your

gas supplier, 3/8-in. approved tubing may be

used where lengths are less than 20 ft. (6.1

m). Larger tubing should be used for lengths

in excess of 20 ft. (6.1 m). Failure to do so can

result in ﬁre, explosion, or death.

•Connect the dryer to the type of gas shown on

the nameplate. Failure to do so can result in ﬁre,

explosion, or death.

•To prevent contamination of the gas valve,

purge the gas supply of air and sediment

before connecting the gas supply to the dryer.

Before tightening the connection between the

gas supply and the dryer, purge remaining air

until the odor of gas is detected. Failure to do

so can result in ﬁre, explosion, or death.

•DO NOT use an open ﬂame to inspect for gas

leaks. Use a noncorrosive leak-detection ﬂuid.

Failure to do so can result in ﬁre, explosion, or

death.

•UseonlyanewAGA-orCSA-certiedgas

supply line with ﬂexible stainless steel

connectors. Failure to do so can result in ﬁre,

explosion, or death.

•Securelytightenallgasconnections. Failure

to do so can result in ﬁre, explosion, or death.

•Use Teﬂon

®

tape or a pipe-joint compound that

is insoluble in Liqueﬁed Petroleum (LP) gas on

all pipe threads. Failure to do so can result in ﬁre,

explosion, or death.

•DO NOT attempt any disassembly of the dryer;

any disassembly requires the attention and

tools of an authorized and qualiﬁed service

person or company. Failure to do so can result

in ﬁre, explosion, or death.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Installation and service must be performed

by a qualiﬁed installer, service agency, or the

gas supplier. Failure to do so can result in ﬁre,

explosion, or death.

•Use only a new stainless steel ﬂexible

connector and a new AGA-certiﬁed

connector. Failure to do so can result in ﬁre,

explosion, or death.

•A gas shutoff valve must be installed within

6 ft. (1.8 m) of the dryer. Failure to do so can

result in ﬁre, explosion, or death.

•The dryer is conﬁgured for Natural Gas when

shipped from the factory. Make sure that the

dryer is equipped with the correct burner

nozzle for the type of gas being used (Natural

Gas or Liqueﬁed Petroleum). Failure to do so

can result in ﬁre, explosion, or death.

•If necessary, the correct nozzle (for the LP

nozzle kit order part number 4948EL4002B)

should be installed by a qualiﬁed technician

and the change should be noted on the dryer.

Failure to do so can result in ﬁre, explosion,

or death.

•All connections must be in accordance with

local codes and regulations. Failure to do so

can result in ﬁre, explosion, or death.

•GasdryersMUSTexhausttotheoutdoors.

Failure to do so can result in ﬁre, explosion,

or death.

3/8" NPT Gas

Connection

Gas Supply

Shutoff Valve

Connecting the Gas Supply

Make sure that the gas supply to the laundry

room is turned OFF. Confirm that the type

of gas available in your laundry room is

appropriate for the dryer. The dryer is

prepared for Natural Gas with a 3/8-in. NPT

gas connection.

Remove the shipping cap from the gas

connection at the back of the dryer. Be

careful not to damage the threads of the gas

connector when removing the shipping cap.

Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel

connector with a 3/8-in. NPT fitting.

Securely tighten all connections between the

dryer and your laundry room’s gas supply.

Turn on your laundry room’s gas supply and

check all pipe connections (both internal and

external) for gas leaks with a noncorrosive

leak-detection fluid.

1

2

3

4

High-Altitude Installations

The BTU rating of this dryer is AGA-certified for

elevations below 10,000 feet.

If your gas dryer is being installed at an elevation

above 10,000 feet, it must be derated by a

qualified technician or gas supplier.

Electrical Connection

Plug dryer into a

120-VAC, 60-Hz.

grounded 3-prong

outlet.

CONNECTING GAS DRYERS (cont.)

1/8" NPT Pipe

Plug

AGA/CSA-Certified

Stainless Steel

Flexible Connector

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

17

18

Electrical Requirements for Electric Models Only

•This dryer must be connected to a grounded

metal, permanent wiring system, or an

equipment-grounding conductor must

be run with the circuit conductors and

connected to the equipment-grounding

terminal or lead on the dryer. Failure to do

so can result in ﬁre, explosion, or death.

•The dryer has its own terminal block that

must be connected to a separate 240 VAC,

60-Hertz, single-phase circuit, fused at 30

amperes (the circuit must be fused on both

sidesoftheline).ELECTRICALSERVICE

FORTHEDRYERSHOULDBEOFTHE

MAXIMUMRATEVOLTAGELISTEDONTHE

NAMEPLATE. DO NOT CONNECT DRYER TO

110-, 115-, OR 120-VOLT CIRCUIT. Heating

elements are available for ﬁeld installation

in dryers which are to be connected to an

electrical service of a different voltage than

that listed on the rating plate. Failure to follow

these instructions can result in ﬁre, explosion,

or death.

•If branch circuit to dryer is 15 ft. (4.5 m)

or less in length, use UL (Underwriters

Laboratories) listed No.-10 AWG wire

(copper wire only), or as required by local

codes. If over 15 ft. (4.50 m), use UL-listed

No.-8 AWG wire (copper wire only), or as

required by local codes. Allow sufﬁcient

slack in wiring so dryer can be moved from

its normal location when necessary. Failure

to do so can result in ﬁre, explosion, or death.

•The power cord (pigtail) connection between

wall receptacle and dryer terminal block

ISNOTsuppliedwithdryer.Typeofpigtail

and gauge of wire must conform to local

codes and with instructions on the following

pages. Failure to follow these instructions can

result in ﬁre, explosion, or death.

•A 4-wire connection is required for all mobile

and manufactured home installations, as

well as all new construction after January

1, 1996. A 4-wire connection must be used

where local codes do not permit grounding

through the neutral wire. Failure to do so can

result in ﬁre, explosion, or death.

Special Electrical Requirements for Mobile or Manufactured Homes

•Any installation in a manufactured or mobile

home must comply with the Manufactured

Home Construction and Safety Standards

Title 24 CFR, Part 32-80 or Standard CAN/

CSA0Z240 MH and local codes and ordinances.

•A 4-wire connection is required for all mobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

Failure to do so can result in ﬁre, explosion,

or death.

CONNECTING ELECTRIC DRYERS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To help prevent fire, electric shock, serious injury, or death, the wiring and

grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all

applicable local regulations. Please contact a qualified electrician to check your home’s wiring and

fuses to ensure that your home has adequate electrical power to operate the dryer.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING:

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Donotmodifytheplugandinternalwire

provided with the dryer.

•Thedryershouldbeconnectedto4-holeoutlet.

•Ifitdoesnotttheoutlet,aproperoutletwill

need to be installed by a qualiﬁed electrician.

19

Remove the terminal block access cover

on the upper back of the dryer. Install a

UL-listed strain relief into the power cord

through-hole; then thread a UL-listed, 30A,

240V, 4-wire, #10 AWG-minimum copper

conductor power cord through the

strain relief.

1

Transfer the dryer’s ground wire from behind

the green ground screw to the center screw

of the terminal block. Attach the two hot

leads of the power cord to the outer terminal

block screws. Attach the white neutral wire

to the center terminal block screw. Attach the

power cord ground wire to the green ground

screw. TIGHTEN ALL SCREWS SECURELY.

Reinstall the terminal block access cover.

2

UL-Listed

Strain Relief

UL-Listed

4-Wire

Power Cord

Terminal

Block

Ground Screw

Neutral

(White)

Hot

(Black)

Power Cord

Ground Wire

Hot

(Red)

CONNECTING ELECTRIC DRYERS (cont.)

Four-Wire Connection for Electric Dryers: Power Cord

•A4-wireconnectionisrequiredforallmobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

•AUL-listedstrainreliefisrequired.

•Usea30-amp, 240V, UL-listed power cord

with #10 AWG-minimum copper conductor

and closed loop or forked terminals with

upturned ends.

wWARNING:

•Connect the power cord to the terminal block. Each colored wire should be connected

to same color screw. Wire color indicated on manual is connected to the same color

screw in block. Failure to follow these instructions may result in a short or overload.

•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit

installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local

codes prohibit grounding through the neutral conductor.

USA ONLY

CONNECTING ELECTRIC DRYERS (cont.)

Remove 5 inches (12.7 cm) of the outer

covering from the wire. Remove 5 inches

of insulation from the ground wire. Cut off

approximately 1

1

⁄

2

inches (3.8 cm) from the

other three wires and strip 1 inch (2.5 cm)

insulation from each wire. Bend the ends of

the three shorter wires into a hook shape.

1

Transfer the dryer’s ground wire from behind

the green ground screw to the center screw

of the terminal block. Attach the two hot

leads of the power cable to the outer terminal

block screws. Attach the white neutral wire

to the center terminal block screw. Attach the

power cable ground wire to the green ground

screw. TIGHTEN ALL SCREWS SECURELY.

Reinstall the terminal block access cover.

3

Ground Wire

Ground Screw

Neutral

(White)

Hot

(Black)

Ground Wire

Hot

(Red)

Remove the terminal block access cover

on the upper back of the dryer. Install a

UL-listed strain relief into the power cord

through-hole; then thread the power cable

prepared in Step 1 through the strain relief.

2

UL-Listed

Strain Relief

UL-Listed

4-Wire

Power Cord

Terminal

Block

5"

(12.7 cm)

1" (2.5 cm)

20

Four-Wire Connection for Electric Dryers: Direct Wire

•A4-wireconnectionisrequiredforallmobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

•AUL-listedstrainreliefisrequired.

•UseUL-listed4-wire #10 AWG-minimum

copper conductor cable.

•Allowatleast5ft(1.5m)lengthtoallowfor

removal and reinstallation of the dryer.

wWARNING:

•Connect the power cord to the terminal block. Each colored wire should be connected

to same color screw. Wire color indicated on manual is connected to the same color

screw in block. Failure to follow these instructions may result in a short or overload.

•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit

installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local

codes prohibit grounding through the neutral conductor.

USA ONLY

La page charge ...

LG Electronics DLE2701V Manuel utilisateur

Ce manuel convient également à

LG Electronics DLE2701V Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents