US Stove Company 5501S Manuel utilisateur

Marque: US Stove Company

Modèle: 5501S

Catégorie: Poêles

Taper: Manuel utilisateur

852473E-3604H

Report No. 0215PS052S

U.S. Environmental Protection Agency

Certied to comply with 2015 particulate

emissions standards.

• Please read this entire manual before installation and use

of this appliance. Failure to follow these instructions could

result in property damage, bodily injury, or even death.

• Contact your local building or re ofcials about

obtaining permits, restrictions and installation inspection

requirements in your area.

• Save these instructions.

• If your heater is not properly installed, a house re may

result. For everyone’s safety, follow all Installation and

Operating Directions. Never use makeshift compromises

during the installation of this appliance. Contact your

local building or re ofcials about restrictions and

installation inspection requirements in your area. These

Pellet Stove Room Heaters have been designed for use in

the US and Canada and are suitable for mobile homes.

Certied to ASTM E 1509-12, and Certied to ULC

S627-00, and(UM) 84-HUD

This unit is not intended to be used as

a primary source of heat.

United States Stove Company

227 Industrial Park Road

South Pittsburg, TN 37380

MODEL: 5501S

Owner’s Operation and Instruction Manual

SAVE THESE INSTRUCTIONS

THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU TO ORDER

REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon monoxide, which

is known to the State of California to cause cancer, birth defects and/or other

reproductive harm. For more information, go to www.P65warnings.ca.gov

Ce produit peut vous exposer à des produits chimiques, y compris le

monoxyde de carbone, qui est connu dans l'État de Californie pour causer

le cancer, des malformations congénitales et / ou d'autres problèmes de

reproduction. Pour plus d'informations, visitez www.P65warnings.ca.gov

This manual describes the installation and operation of the U.S. Stove, 5501S wood heater. This heater meets the 2015 U.S.

Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2015. Under specic test

conditions this heater has been shown to deliver heat at rates ranging from 8,606 to 20,076 Btu/hr. This heater achieved a

particulate emissions rate of 1.03 g/hr when tested to method ASTM E2779-10 (*and an efciency of 68.53 %).

• IMPORTANT: Read this entire manual before installing

and operating this product. Failure to do so may

result in property damage, bodily injury, or even

death. Proper installation of this stove is crucial for

safe and efcient operation.

• Install vent at clearances specied by the vent

manufacturer.

• Do not connect the pellet vent to a vent serving any

other appliance or stove.

• Do not install a ue damper in the exhaust venting

system of this unit.

• Use of outside air is not required for this unit.

• Contact your local building ofcials to obtain a

permit and information on any additional installation

restrictions or inspection requirements in your area.

• Do not throw this manual away. This manual has

important operating and maintenance instructions

that you will need at a later time. Always follow the

instructions in this manual.

• This appliance is designed for the use of pelletized fuel

that meet or exceed the standard set by the Pellet

Fuel Institute(PFI).

• Never use gasoline, gasoline-type lantern fuel,

kerosene, charcoal lighter uid, or similar liquids to

start or ’freshen up’ a re in this stove. Keep all such

liquids well away from the stove while it is in use.

• A working smoke detector must be installed in the

same room as this product.

• Install a smoke detector on each oor of your home;

incase of accidental re from any cause it can

provide time for escape.

• The smoke detector must be installed at least 15 feet

(4,57 M) from the appliance in order to prevent undue

triggering of the detector when reloading.

• Do not unplug the stove if you suspect a malfunction.

Turn the ON/OFF SWITCH to ”OFF’ and contact your

dealer.

• Your stove requires periodic maintenance and

cleaning (see ”MAINTENANCE ”). Failure to maintain

your stove may lead to improper and/or unsafe

operation.

• Disconnect the power cord before performing any

maintenance! NOTE: Turning the ON/OFF Switch to

”OFF” does not disconnect all power to the electrical

components of the stove.

• Never try to repair or replace any part of the stove

unless instructions for doing so are given in this

manual. All other work should be done by a trained

technician.

• Do not operate your stove with the viewing door

open. The auger will not feed pellets under these

circumstances and a safety concern may arise from

sparks or fumes entering the room.

• Allow the stove to cool before performing any

maintenance or cleaning. Ashes must be disposed

in a metal container with a tight tting lid. The closed

container of ashes should be placed on a non-

combustible surface or on the ground, well away from

all combustible materials, pending nal disposal.

• The exhaust system should be checked monthly

during the burning season for any build-up of soot or

creosote.

• Do not touch the hot surfaces of the stove. Educate

all children on the dangers of a high-temperature

stove. Young children should be supervised when they

are in the same room as the stove.

• The hopper and stove top will be hot during

operation; therefore, you should always use some

type of hand protection when refueling your stove.

• A power surge protector is required. This unit must be

plugged into a 110 - 120V, 60 Hz grounded electrical

outlet. Do not use an adapter plug or sever the

grounding plug. Do not route the electrical cord

underneath, in front of, or over the heater. Do not

route the cord in foot trafc areas or pinch the cord

under furniture.

• The heater will not operate during a power outage.

If a power outage does occur, check the heater for

smoke spillage and open a window if any smoke spills

into the room.

• The feed door must be closed and sealed during

operation.

• Never block free airow through the open vents of the

unit.

• Keep foreign objects out of the hopper.

• The moving parts of this stove are propelled by high

torque electric motors. Keep all body parts away

from the auger while the stove is plugged into an

electrical outlet. These moving parts may begin to

move at any time while the stove is plugged in.

• Do not place clothing or other ammable items on or

near this stove.

• When installed in a mobile home, the stove must be

grounded directly to the steel chassis and bolted

to the oor. WARNING—THIS UNIT MUST NOT BE

INSTALLED IN THE BEDROOM (per HUD requirements).

CAUTION—The structural integrity of the mobile home

oor, wall, and ceiling/roof must be maintained.

• This appliance is not intended for commercial use.

• CAUTION: Burning fuel creates carbon monoxide

and can be hazardous to your health if not properly

vented.

*This appliance is a freestanding heater. It is not intended to be attached to any type of ducting. It is not a furnace.

Safety Precautions

Note: Register your product on line at www.usstove.com. Save your receipt with your records for any

claims.

Specications

* Pellet size may effect the actual rate of fuel feed and burn times. Fuel feed rates may vary by as much as 20%. Use PFI

listed fuel for best results.

FUEL CONSIDERATIONS

Your pellet stove is designed to burn premium hardwood pellets that comply with the Pellet Fuels Institute(PFI) standard

(minimum of 40 lbs density per cubic ft, 1/4” to 5/16” diameter, length no greater than 1.5”, not less than 8,200 BTU/lb,

moisture under 8% by weight, ash under 1% by weight, and salt under 300 parts per million). Pellets that are soft, contain

excessive amounts of loose sawdust, have been, or are wet, will result in reduced performance.

Store your pellets in a dry place. DO NOT store the fuel within the installation clearances of the unit or within the space

required for refuelling and ash removal. Doing so could result in a house re.

Do not over re or use volatile fuels or combustibles, doing so may cause a personal and property damage hazards.

SAFETY AND EPA COMPLIANCE

Your pellet stove has been approved for installation in the USA and Canada. It may also be installed in a manufactured

or mobile home. Your stove is Certied to ASTM E 1509-12, and Certied to ULC S627-00, and(UM) 84-HUD.

Electrical Specications

Electrical Rating 110-120 volts ac, 60 HZ, 3.0 Amps

Watts (operational) 125

Watts (igniter running) 310

Dimensions

Height 30.125” (76.5cm)

Width 18.5” (47mm)

Depth 20.375” (51.75mm)

Weight 128lbs

Flue Size 3” or 4”

Heating Specications

Fuel Burn Rate* (lowest setting) 1.5 lbs./hr. (0.7 kg/hr)

Burn Time (lowest setting) 13 hrs. (approximate)

Hopper Capacity 20 lbs. (9.1kg)

Flue Size 3” or 4”

WARNING: It is against federal regulations to operate this wood heater in a manner inconsistent with the

operating instructions in the owner’s manual.

INSTALLATION OPTIONS

Read this entire manual before you install and use your

pellet stove. Failure to follow instructions may result in

property damage, bodily injury, or even death!

(See specic installation details for clearances and other

installation requirements)

A Freestanding Unit—supported by pedestal/legs and

placed on a non-combustible oor surface in compliance

with clearance requirements for a freestanding stove

installation.

Your pellet stove may be installed to code in either a

conventional or mobile home (see SPECIAL MOBILE HOME

REQUIREMENTS). The installation must comply with the

Manufactured Home and Safety Standard (HUD), CFR3280,

Part 24.

It is recommended that only a authorized technician install

your pellet stove, preferably an NFI certied specialist.

DO NOT CONNECT THIS UNIT TO ANY AIR DISTRIBUTION DUCT

OR SYSTEM.

The use of other components other than stated herein

could cause bodily harm, heater damage, and void your

warranty.

IMPROPER INSTALLATION: The manufacturer will not be held

responsible for damage caused by the malfunction of a

stove due to improper venting or installation. Call (800) 750-

2723 and/or consult a professional installer if you have any

questions.

CLEARANCES

Your pellet stove has been tested and listed for installation

in residential, mobile home in accordance with the

clearances given below. For safety reasons, please adhere

to the installation clearances and restrictions. Any reduction

in clearance to combustibles may only be done by means

approved by a regulatory authority.

FLOOR PROTECTION

This heater must have a non-combustible oor protector

(UL1618 ember protection) installed beneath it if the oor is

of combustible material. US: Floor protector should be UL

listed or equal too, needs to extend 6” to the front, 6” to

each side, 1” to the rear of the unit. Under and 2” beyond

each side of the cleanout tee if an interior vertical instillation.

Canada: Floor protector should comply with CAN/

ULC standards. Needs to extend 18” to the front, 8” beyond

each side of the unit.

ADJACENT WALL

Installation

CLEARANCES

A Side Wall to Stove 10 in (254 mm)

B Side Wall to Vent Pipe 11.5 in (292 mm)

C Back Wall to Stove 11.875 in (302 mm)

D Back Wall to Vent Pipe 3 in (76 mm)

E Ceiling to Floor 84 in (2134 mm)

F Ceiling to Stove 53.875 in (1434 mm)

CORNER CLEARANCES

G Side Wall to Stove 7.5 in (191 mm)

H Side Wall to Vent Pipe 11.25 in (286 mm)

I Back Wall to Stove 7.5 in (191 mm)

J Back Wall to Vent Pipe 3 in (76 mm)

FLOOR PROTECTOR CLEARANCES

K Back to Stove

U.S. 1 in (26 mm)

Canada 8 in (204 mm)

L Side to Stove

U.S. 6 in (153 mm)

Canada 8 in (204mm)

M Front to Stove

U.S. 6 in (153 mm)

Canada 8 in (204 mm)

N Back to Flue 2 in (51 mm)

O Overall Length 31 in (788 mm)

P Overall Width 38 in (966 mm)

THROUGH THE WALL

INSTALLATION

INTERIOR VERTICAL

INSTALLATION

VENTING REQUIREMENTS

• Install vent at clearances specied by the vent manufacturer.

• Do not connect the pellet vent to a vent serving any other appliance or stove.

• Do not install a ue damper in the exhaust venting system of this unit.

The following installation guidelines must be followed to ensure conformity with both the safety listing of this stove and to

local building codes. Do not use makeshift methods or compromise in the installation.

MAXIMUM VENTING DISTANCE

Installation MUST include at least 3-feet of vertical pipe outside the home. This will create some natural draft to reduce

the possibility of smoke or odor during appliance shutdown and keep exhaust from causing a nuisance or hazard by

exposing people or shrubs to high temperatures. The maximum recommend vertical venting height is 12-feet for 3-inch

type “PL” vent. Total length of horizontal vent must not exceed 4-feet. This could cause back pressure. Use no more than

180 degrees of elbows (two 90-degree elbows, or two 45-degree and one 90-degree elbow, etc.) to maintain adequate

draft.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your chimney

depends on the length of the chimney, local geography, nearby obstructions and other factors. Too much draft may

cause excessive temperatures in the appliance. Inadequate draft may cause backpufng into the room and ‘plugging’

of the chimney.

Inadequate draft will cause the appliance to leak smoke into the room through appliance and chimney connector

joints. An uncontrollable burn or excessive temperature indicates excessive draft.

Take into account the chimney’s location to insure it is not too close to neighbours or in a valley which may cause

unhealthy or nuisance conditions.

PELLET VENT TYPE

A UL listed 3-inch or 4-inch type “PL” pellet vent exhaust system must be used for installation and attached to the pipe

connector provided on the back of the stove (use a 3-inch to 4-inch adapter for 4-inch pipe). Connection at back of

stove must be sealed using Hi-Temp RTV. Use 4-inch vent if the vent height is over 12-feet or if the installation is over 2,500

feet above sea level. We recommend the use of Simpson Dura-Vent® or Metal-Fab® pipe (if you use other pipe, consult

your local building codes and/or building inspectors). Do not use Type-B Gas Vent pipe or galvanized pipe with this unit.

The pellet vent pipe is designed to disassemble for cleaning and should be checked several times during the burning

season. Pellet vent pipe is not furnished with the unit and must be purchased separately.

PELLET VENT INSTALLATION

The installation must include a clean-out tee to enable collection of y ash and to permit periodic cleaning of the

exhaust system. 90-degree elbows accumulate y ash and soot thereby reducing exhaust ow and performance of the

stove. Each elbow or tee reduces draft potential by 30% to 50%.

All joints in the vent system must be fastened by at least 3 screws, and all joints must be sealed with Hi-Temp RTV silicone

sealant to be airtight. The area where the vent pipe penetrates to the exterior of the home must be sealed with silicone

or other means to maintain the vapor barrier between the exterior and the interior of the home. Vent surfaces can get

hot enough to cause burns if touched by children. Noncombustible shielding or guards may be required.

PELLET VENT TERMINATION

Do not terminate the vent in an enclosed or semi-enclosed area, such as; carport, garage, attic, crawl space, under

a sun deck or porch, narrow walkway, or any other location that can build up a concentration of fumes. Termination in

one of these areas can also lead to unpredictable pressure situations with the appliance, and could result in improper

performance and/or malfunction. The termination must exhaust above the outside air inlet elevation. The termination

must not be located where it will become plugged by snow or other materials. Do not terminate the venting into an

existing steel or masonry chimney.

IMPORTANT: This unit is equipped with a negative draft system that pulls air through the burn pot and

pushes the exhaust out of the dwelling. If this unit is connected to a ue system other than the way

explained in this manual, it will not function properly.

Installation

VENT TERMINATION CLEARANCES

A. Minimum 4-foot (1.22m) clearance below or beside any door or window that opens.

B. Minimum 1-foot (0.3m) clearance above any door or window that opens.

C. Minimum 3-foot (0.91m) clearance from any adjacent building.

D. Minimum 7-foot (2.13m) clearance from any grade when adjacent to public walkways.

E. Minimum 2-foot (0.61m) clearance above any grass, plants, or other combustible materials.

F. Minimum 3-foot (0.91m) clearance from an forced air intake of any appliance.

G. Minimum 2-foot (0.61m) clearance below eves or overhang.

H. Minimum 1-foot (0.3m) clearance horizontally from combustible wall.

I. Must be a minimum of 3 foot (0.91m) above the roof and 2 foot (0.61m) above the highest point or the roof within

10 feet (3.05m).

VENT TERMINATION

CLEARANCES

Installation

THROUGH THE WALL INSTALLATION

(RECOMMENDED INSTALLATION)

Canadian installations must conform to CAN/CSA-B365.

To vent the unit through the wall, connect the pipe adapter

to the exhaust motor adapter. If the exhaust adapter is at

least 18 in.(457mm) above ground level, a straight section of

pellet vent pipe can be used through the wall.

Your heater dealer should be able to provide you with a kit

that will handle most of this installation, which will include a

wall thimble that will allow the proper clearance through a

combustible wall. Once outside the structure, a 3 in.(76mm)

clearance should be maintained from the outside wall and a

clean out tee should be placed on the pipe with a 90-degree

turn away from the house. At this point, a 3ft (0.91m)

(minimum) section of pipe should be added with a horizontal

cap, which would complete the installation.

A support bracket should be placed just below the

termination cap or one every 4ft (1.22m) to make the system

more stable. If you live in an area that has heavy snowfall, it is

recommended that the installation be taller than 3ft (0.91m)

to get above the snowdrift line. This same installation can be

used if your heater is below ground level by simply adding the

clean-out section and vertical pipe inside until ground level

is reached. With this installation you have to be aware of the

snowdrift line, dead grass, and leaves. We recommend a 3ft

(0.91m) minimum vertical rise on the inside or outside of the

house.

The “through the wall” installation is the least expensive and

simplest installation. Never terminate the end vent under a

deck, in an alcove, under a window, or between two windows.

We recommend Simpson Dura-Vent® or Metal-Fab® kits.

THROUGH THE ROOF/CEILING INSTALLATION

When venting the heater through the ceiling, the pipe is connected the same as through the wall, except the clean-out

tee is always on the inside of the house, and a 3 in.(76mm) adapter is added before the clean-out tee.

You must use the proper ceiling support anges and roof ashing (supplied by the pipe manufacturer; follow the pipe

manufacturer’s directions). It is important to note that if your vertical run of pipe is more than 12ft (3.7m), the pellet vent

pipe size should be increased to 4 in. (102mm) in diameter.

Do not exceed more than 4ft (1.22m) of pipe on a horizontal run and use as few elbows as possible. If an offset is

required, it is better to install 45-degree elbows rather than 90-degree elbows.

Installation

TYPICAL THROUGH THE WALL

INSTALLATION

ATTENTION: DO NOT vent under any porch, deck, awning, or in any semi enclosed or roofed area. Doing

so may result in unpredictable airow at the vent cap under certain conditions and can affect the

performance of your stove, as well as, other unforeseeable issues.

SPECIAL MOBILE HOME REQUIREMENTS

• WARNING! - Do not install in a sleeping room

• CAUTION! - The structural integrity of the mobile

home oor, wall, and ceiling/roof must be

maintained.

NOTE: Installation should be in accordance with the

Manufactured Home and Safety Standard (HUD), CFR

3280, Part 24.

In addition to the previously detailed installation

requirements, mobile home installations must meet the

following requirements:

• This stove must be securely fastened to the oor

of the mobile home through the two holes in the

rear of the stove using 2, ¼” lag bolts that are long

enough to go through both a hearth pad, if used,

and the oor of the home.

• The heater must be electrically grounded to the

steel chassis of the mobile home with 8 GA copper

wire using a serrated or star washer to penetrate

paint or protective coating to ensure grounding.

• Vent must be 3 or 4-inch “PL” Vent and must extend

a minimum or 36 in.(914mm) above the roof line of the mobile home and must be installed using a UL listed ceiling

re stop and rain cap.

• When moving your mobile home, all exterior venting must be removed while the mobile home is being relocated.

After relocation, all venting must be reinstalled and securely fastened.

• Outside Air is mandatory for mobile home installation. See Outside Air Supply section and your dealer for purchasing.

• Check with your local building ofcials as other codes may apply.

NOTE: Dimensions from the oor

to your stoves inlet/exhaust pipes

are approximate and may vary

depending on your installation.

8.14

8.10

30.20

5.55

Exhaust Outlet

Fresh Air Intake

TYPICAL FRESH AIR

TERMINATION

EXHAUST/INLET

LOCATIONS

OUTSIDE AIR SUPPLY (OPTIONAL, UNLESS INSTALLING IN A MOBILE HOME)

Adequate ventilation air is required to operate this heater. During operation, the heater draws air for combustion which

can be assisted by the installation of outside combustion air inlets. However, certain weather conditions such as icing

or use of kitchen exhaust fans may impact and reduce the effectiveness of vents. It is important to note that room air

starvation will negatively impact the operation of the heater.

Depending on your location and home construction, outside air may be necessary for optimal performance. Metal pipe

(solid or exible) must be used for the outside air installation. PVC pipe is NOT approved and should NEVER be used. A

wind shield over the termination of the outside air pipe or a 90-degree elbow or bend away from the prevailing winds

MUST be used when an outside air pipe is installed through the side of a building. The outside air termination MUST be at

least 1ft (0.305m) away from the exhaust system termination.

The outside air pipe on your heater is 2” (50.8mm) OD. The outside air connecting pipe must be at least 2” (50.8mm) ID.

The outside air connection used MUST NOT restrict the amount of air available to your heater. The outside air connecting

pipe must be as short and free of bends as possible, and it must t over, not inside, the outside air connection to the

heater.

MOBILE HOME

MOUNTING BOLT HOLES

Installation

Assembly Instructions

STEP 1

Pull the factory installed wires out of the top of the

stove. There will be two wire harnesses, as shown.

STEP 2

Unpack the top mount controls and ensure that

the wiring harness shown is attached securely.

STEP 3

Connect the factory installed wiring harnesses to

the control panel as shown.

STEP 4

Attach the control panel to the top of the stove,

as shown.

STEP 5

Secure with two sheet metal screws.

PANEL CONTROLS

The blowers and automatic fuel supply are controlled from a panel on the top of this unit. The control panel functions

are a follows.

A. ON/OFF SWITCH (“POWER” BUTTON)

• When pushed, the stove will automatically ignite. No other re starter is necessary. The igniter will stay on for at

least 10 and up to 12 minutes, depending on when Proof of Fire is reached. The re should start in approximately

5 minutes.

• The red light located above the “POWER” button will turn green when pressed and remain green until the stove

is turned off.

• After pushing “POWER”, the auger motor is on for 3.5 minutes, off for 1 minute. During the remainder of the start-

up period, the auger motor operates on the heat range “1” setting.

• During start up the heat level advance (Up and Down keys) will change the heat range indicator level

accordingly, but there is no change in the stoves operating conditions until start-up is completed.

• During start-up ignition must occur within 12 minutes or the stove will error out and show E4.

• During the start-up phase, the Mode key does not function.

Control Panel

A. LEVEL / TEMP ARROW BUTTONS

• These buttons when pushed will set the pellet feed rate, hence the heat output or heat range of your stove.

• The levels of heat output will incrementally change on the bar graph starting from heat range “1” to heat range

“5”.

B. °C / °F Button

• The °C / °F button changes the two digit display from degrees Celsius to degrees Fahrenheit.

C. MODE (M/T) BUTTON

• The Mode of the stove can be switched between manual and controlled with a Thermostat. Separate LEDs to

the left of the two digit display indicate the mode of operation – Manual or T-Stat. The stove has to be in normal

operation to be switched from Manual to T-Stat mode.

• Manual mode operates according to the 5 set levels of feed on the bar graph from heat range “1” to heat

range “5”.

• T-Stat mode works as follows:

• The stove has a built in Thermostat into the controls of the appliance. The temperature sensor for the T-Stat is

located on the back of the stove behind the display board.

• Once the stove has gone into run mode the stove can be switch into T-Stat mode.

• The Up and Down Level / Temp Arrow buttons are used to change the desired set-point temperature. Once

the desired temperature is reached the two digit display will ash for four seconds and reset to the actual room

temperature.

• Once the stove reaches within 3°F of the desired temperature set point, it returns to the heat range that the

stove was set on before it was switched to T-Stat mode (if the stove was running on heat range “5” when

switched to T-stat mode when it gets within 3°F of the set point it will return to heat range “5”).

• Once the stove reaches the desired set-point, the stove will drop to heat range “1”.

• When room temperature drops below desired set-point the stove will ramp back up until it reaches the desired

temperature.

Level / Temp

Manual

T-Stat

CONTROLS

It is a common occurrence in the pellet

industry for the average pellet size to vary.

Due to the varying sizes of pellets, this

appliance utilizes a fuel adjuster to adjust

the amount of fuel allowed to pass into the

auger assembly. The fuel adjuster is located

inside the hopper.

Note: To increase the ow of pellets move

the fuel adjuster up. To decrease the ow of

pellets move the fuel adjuster down.

HOW TO ADJUST THE FUEL ADJUSTER

1. Turn off and unplug the appliance.

2. Loosen the two wing-nuts.

3. Adjust up to increase, or down to

reduce the fuel usage based on the

size of the pellets.

4. Tighten the two wing-nuts.

Wing Nuts

UP - Increase

Pellet Flow

Down - Decrease

Pellet Flow

• DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE - Never use gasoline, gasoline-type lantern fuel, kerosene,

charcoal lighter uid, or similar liquids to start or “freshen up” a re in this stove. Keep all such liquids well away from

the stove while it is in use.

• HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS.

This heater is designed to burn only PFI Premium grade pellets. This appliance can also burn pellets rated as standard

after May 16, 2015.

DO NOT BURN:

1. Garbage;

2. Lawn clippings or yard waste;

3. Materials containing rubber, including tires;

4. Materials containing plastic;

5. Waste petroleum products, paints or paint thinners, or

asphalt products;

6. Materials containing asbestos;

7. Construction or demolition debris;

8. Railroad ties or pressure-treated wood;

9. Manure or animal remains;

10. Salt water driftwood or other previously salt water

saturated materials;

11. Unseasoned wood; or

12. Paper products, cardboard, plywood, or

particleboard. The prohibition against burning these

materials does not prohibit the use of re starters

made from paper, cardboard, saw dust, wax and

similar substances for the purpose of starting a re in

an affected wood heater.

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

PROPER FUEL

THIS STOVE IS APPROVED FOR BURNING PELLETIZED WOOD FUEL ONLY ! Factory-approved pellets are those 1/4” or 5/16” in

diameter and not over 1” long. Longer or thicker pellets sometimes bridge the auger ights, which prevents proper pellet

feed. Burning wood in forms other than pellets is not permitted. It will violate the building codes for which the stove has

been approved and will void all warranties. The design incorporates automatic feed of the pellet fuel into the re at a

carefully prescribed rate. Any additional fuel introduced by hand will not increase heat output but may seriously impair

the stoves performance by generating considerable smoke. Do not burn wet pellets. The stove’s performance depends

heavily on the quality of your pellet fuel. Avoid pellet brands that display these characteristics:

1. Excess Fines – “Fines” is a term describing crushed pellets or loose material that looks like sawdust or sand. Pellets can

be screened before being placed in hopper to remove most nes.

2. Binders – Some pellets are produced with materials to hold the together, or “bind” them.

3. High ash content – Poor quality pellets will often create smoke and dirty glass. They will create a need for more

frequent maintenance. You will have to empty the burn pot plus vacuum the entire system more often. Poor quality

pellets could damage the auger. We cannot accept responsibility for damage due to poor quality pellet.

PRE-START-UP CHECK

Remove burn pot, making sure it is clean and none of the air holes are plugged. Clean the rebox, and then reinstall burn

pot. Clean door glass if necessary (a dry cloth or paper towel is usually sufcient). Never use abrasive cleaners on the glass

or door. Check fuel in the hopper, and rell if necessary.

BUILDING A FIRE

Never use a grate or other means of supporting the fuel. Use only the burn pot supplied with this heater.

Hopper lid must be closed in order for the unit to feed pellets.

During the start-up period:

1. Make sure burn pot is free of pellets.

2. DO NOT open the viewing door.

3. Damper may need to be closed during start up.

4. DO NOT add pellets to the burn pot by hand.

NOTE: During the rst few res, your stove will emit an odor as the high temperature paint cures or becomes seasoned to

the metal. Maintaining smaller res will minimize this. Avoid placing items on stove top during this period because paint

could be affected.

Attempts to achieve heat output rates that exceed heater design specications can result in permanent damage to

the heater.

AUTOMATIC IGNITOR

Fill hopper and clean burn pot.

1. Press “On/Off” button. Make sure green light comes on.

2. The damper should be completely closed or open no more than ¼ of the way during start-up. This will vary depending

on your installation and elevation. Once re is established adjust for desired ame increasing the amount the damper

is open as the heat setting is increased. (See “DAMPER CONTROL”)

3. Adjust feed rate to desired setting by pressing “Heat Level Advance” button.

If re doesn’t start in 12 minutes, press “On/Off”, wait a few minutes, clear the burn pot, and start procedure again.

Operation

DAMPER CONTROL

The damper control lever is located on the back of the stove on the lower left side. The damper adjusts the combustion

air. This control is necessary due to the varied burn characteristics of individual installations, different pellet brands and

pellet feed rates. It allows you to improve the efciency of your stove. Providing correct combustion air will reduce the

frequency of cleaning your glass door and prevent the rapid buildup of creosote inside your stove and chimney.

You should adjust the damper based on the re’s appearance. A low, reddish, dirty re can be improved by turning the

damper slightly to the right. A “blow torch” re can be improved by turning the dampener to the left a little bit.

As a general rule, on lower feed rate settings, the damper should be farther to the left closing it off. On higher feed rates,

the damper should be open more by having it set more towards the right. Through trial and error, you will nd the best

setting. Consult your dealer if you need help.

NOTE: On heat range “1”, damper should be either completely closed or open no more than a ¼ of the way. If damper

is open to far, it can cause the re to go out.

OPENING DOOR

If the door is opened while the stove is in operation it must be closed within 30 seconds or the stove will shut down. If the

stove shuts down push the “On/Off” button to re-start your stove. The stove will have to fully shut down and turn off before

you will be able to restart the stove.

ROOM AIR FAN

When starting your stove the Room Air Fan will not come on until the stove’s heat exchanger warms up. This usually takes

about 10 minutes from start-up.

IF STOVE RUNS OUT OF PELLETS

The re goes out and the auger motor and blowers will run until the stove cools. This will take 30 minutes or longer

depending on the heat remaining in the appliance. After the stove components stop running all lights on the display will

go out and the two digit display will begin ashing “E3”

REFUELLING

• The hopper and stove top will be hot during operation; therefore, you should always use some type of hand

protection when refuelling your stove.

• Never place your hand near the auger while the stove is in operation.

We recommend that you not let the hopper drop below ¼ full.

TAMPER WARNING

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal regulations

to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating instructions in this

manual.

KEEP HOPPER LID CLOSED AT ALL TIMES EXCEPT WHEN REFILLING.

DO NOT OVERFILL HOPPER.

SHUTDOWN PROCEDURE

Turning your stove off is a matter of pressing the “POWER” button on the display board. The green light will turn back to

red when the “POWER” button is pushed. The auger motor will stop, and the blowers will continue to operate until the

internal rebox temperatures have fallen to a preset level.

1. Your stove is equipped with a high temperature thermodisc. This unit has a manual reset thermodisc. This safety

switch has two functions.

A. To recognize an overheat situation in the stove and shut down the fuel feed or auger system.

B. In case of a malfunctioning convection blower, the high-temperature thermodisc will automatically shut down

the auger, preventing the stove from overheating.

NOTE: On some units, once tripped, like a circuit breaker, the reset button will have to be pushed before restarting your

stove. On other units the thermodisc has no reset button and will reset itself once the stove has cooled. The manufacturer

recommends that you call your dealer if this occurs as this may indicate a more serious problem. A service call may be

required.

2. If the combustion blower fails, an air pressure switch will automatically shut down the auger.

NOTE: Opening the stove door for more than 30 seconds during operation will cause enough pressure change to activate

the air switch, shutting the fuel feed off. The stove will shut down and show “E2” on the two digit display. The stove has

to fully shut down before restarting.

WARNING: Never shut down this unit by unplugging it from the power source.

WARNING: FAILURE TO PROPERLY MAINTENANCE THE CLEAN OUTS

WILL RESULT IN POOR PERFORMANCE OF THIS STOVE.

INTERIOR CHAMBERS

• Burn Pot: Periodically remove and clean the burn pot and the area inside the burn pot housing. In particular, it is

advisable to clean out the holes in the burn pot to remove any build up that may prevent air from moving through

the burn pot freely.

• Heat Exchanger: There is a clean out plate on both sides of the heat exchanger that need to be removed to clean

y ash out of the heat exchanger. The cleanouts are located inside the cabinet doors, on the lower front corners of

the heat exchanger. To access these clean outs, you must remove both side panels. The clean outs are secured

to the rebox with (2) 5/16” screws. Remove the clean outs and vacuum out any accumulated ash. This should be

done at least once per month or more frequently if large amounts of ash are noticed while cleaning or if the stove

does not seem to be burning properly.

If a vacuum is used to clean your stove, we suggest using a vacuum designed for ash removal. Some regular vacuum

cleaner (i.e. shop vacs) may leak ash into the room.

DO NOT VACUUM HOT ASH

Clean-Out

Plate

Clean-Out

Plate

• Failure to clean and maintain this unit as indicated can result in poor performance, safety hazards, re, and even

death.

• Unplug your stove’s electrical cord prior to removing the back panel or opening the exhaust system for any inspection,

cleaning, or maintenance work.

• Never perform any inspections, cleaning, or maintenance on a hot stove.

• Do not operate stove with broken glass, leakage of ue gas may result.

EXHAUST SYSTEM

Creosote Formation – When any wood is burned slowly, it produces tar and other organic vapors, which combine with

expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney ue or a newly started

re or from a slow-burning re. As a result, creosote residue accumulates on the ue lining. When ignited, this creosote

makes an extremely hot re, which may damage the chimney or even destroy the house. Despite their high efciency,

pellet stoves can accumulate creosote under certain conditions.

Fly Ash – This accumulates in the horizontal portion of an exhaust run. Though non-combustible, it may impede the

normal exhaust ow. It should therefore be periodically removed.

Inspection and Removal – The chimney connector and chimney should be inspected by a qualied person annually or

per ton of pellets to determine if a creosote or y ash build-up has occurred. If creosote has accumulated, it should be

removed to reduce the risk of a chimney re. Inspect the system at the stove connection and at the chimney top. Cooler

surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from the

bottom. The creosote should be removed with a brush specically designed for the type of chimney in use. A qualied

chimney sweep can perform this service. It is also recommended that before each heating season the entire system be

professionally inspected, cleaned and, if necessary, repaired. To clean the chimney, disconnect the vent from the stove.

ASH REMOVAL

Remove the ashes periodically to avoid unnecessary ash build up. Ash removal is as follows:

1. Let re burn out and allow unit cool to room temperature.

2. Clean the heat exchanger tubes (see Heat Exchanger Cleaning section) – Make sure Pellet Stove is at room

temperature before touching .

3. Open the ash pan door, remove the burn pot and empty into metal container.

4. Vacuum to remove ashes from the rebox.

5. BE SURE THAT ASHES ARE COOL TO THE TOUCH BEFORE VACUUMING. Some vacuum cleaners may leak ash into the

room. Your vacuum cleaner should have a special lter or bag to eliminate leakage.

6. Remove ash pan and dispose of ashes into metal container.

7. Reinstall ash pan.

8. Reinstall burn pot.

ASH DISPOSAL

Remove ashes when unit has cooled. Ashes should be placed in a metal container with a tight tting lid. The closed

container of ashes should be placed on a noncombustible oor or on the ground, well away from all combustible

materials, pending nal disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be

retained in the closed container until all embers have been thoroughly cooled. The container shall not be used for other

trash or waste disposal. If combined with combustible substances, ashes and embers may ignite.

SMOKE AND CO MONITORS

Burning wood naturally produces smoke and carbon monoxide(CO) emissions. CO is a poisonous gas when exposed to

elevated concentrations for extended periods of time. While the modern combustion systems in heaters drastically reduce

the amount of CO emitted out the chimney, exposure to the gases in closed or conned areas can be dangerous. Make

sure you stove gaskets and chimney joints are in good working order and sealing properly to ensure unintended exposure.

It is recommended that you use both smoke and CO monitors in areas having the potential to generate CO.

CHECK AND CLEAN THE HOPPER

Check the hopper periodically to determine if there is any sawdust (nes) that is building up in the feed system or pellets

that are sticking to the hopper surface. Clean as needed.

DOOR AND GLASS GASKETS

Inspect the main door and glass window gaskets periodically. The main door may need to be removed to have frayed,

broken, or compacted gaskets replaced by your authorized dealer. This unit’s door uses a 5/8” diameter rope gasket.

BLOWER MOTORS

Clean the air holes on the motors of both the exhaust and distribution blowers annually. Remove the exhaust blower from

the exhaust duct and clean out the internal fan blades as part of your fall start-up. If you have indoor pets your power

motors should be inspected monthly to make sure they are free of animal hair build up. Animal hair build up in blowers

can result in poor performance or unforeseen safety hazards.

Maintenance

PAINTED SURFACES

Painted surfaces may be wiped down with a damp cloth. If scratches appear, or you wish to renew your paint, contact

your authorized dealer to obtain a can of suitable high-temperature paint.

GLASS - CLEANING, REMOVAL, AND REPLACEMENT OF BROKEN DOOR GLASS

Cleaning - We recommend using a high quality glass cleaner. Should a buildup of creosote or carbon accumulate, you

may wish to use 000 steel wool and water to clean the glass. DO NOT use abrasive cleaners. DO NOT perform the cleaning

while the glass is HOT. ,

In the event you need to replace the glass, Do not attempt to operate the unit with broken glass. Replacement glass may

be purchased from your U.S. Stove Pellet Burning Room Heater Dealer. If glass is broken, follow these removal procedures:

Replacement glass must be 0.197” thick tempered ceramic glass with a working service temperature of 1400

deg. F.

1. Remove the four (4) screws and glass retainers.

2. While wearing leather gloves (or any other gloves suitable for handling broken glass), carefully remove

any loose pieces of glass from the door frame. Dispose of all broken glass properly. ONLY high temperature

ceramic glass of the correct size and thickness may be used. DO NOT substitute alternative materials for

the glass. Contact your authorized dealer to obtain this glass.

3. Re-install the new glass by re-attaching the retainers and screws, be careful not to over tighten the

screws for this could damage the glass.

DO NOT abuse the door glass by striking, slamming, or similar trauma. Do not operate the stove with the glass

removed, cracked, or broken.

FALL START UP

Prior to starting the rst re of the heating season, check the outside area around the exhaust and air intake systems for

obstructions. Clean and remove any y ash from the exhaust venting system. Clean any screens on the exhaust system

and on the outside air intake pipe. Turn all of the controls on and make sure that they are working properly. This is also a

good time to give the entire stove a good cleaning throughout.

SPRING SHUTDOWN

After the last burn in the spring, remove any remaining pellets from the hopper and the auger feed system. Scoop out

the pellets and then run the auger until the hopper is empty and pellets stop owing (this can be done by pressing the

“ON” button with the viewing door open). Vacuum out the hopper. Thoroughly clean the burn pot, and rebox. It may be

desirable to spray the inside of the cleaned hopper with an aerosol silicone spray if your stove is in a high humidity area.

The exhaust system should be thoroughly cleaned.

MAINTENANCE SCHEDULE

Use the following as a guide under average use conditions.

Gaskets around door and door glass should be inspected and repaired or replaced when necessary.

Daily Weekly Monthly or as needed

Burn Pot Stirred Empty

Combustion Chamber Brushed

Ashes Check Empty

Interior Chambers Vacuumed

Combustion Blower Blades Vacuumed / Brushed

Convection Blower Impeller Vacuumed / Brushed

Vent System Cleaned

Gaskets Inspected

Glass Wiped Cleaned

Hopper (end of season) Empty and vacuumed

Maintenance

When your stove acts out of the ordinary, the rst reaction is to call for help. This guide may save time and money by

enabling you to solve simple problems yourself. Problems encountered are often the result of only ve factors: 1) poor

fuel; 2) poor operation or maintenance; 3) poor installation; 4) component failure; 5) factory defect. You can usually solve

those problems related to 1 and 2. Your dealer can solve problems relating to 3, 4 and 5. Refer to diagrams on page 25

to help locate indicated parts.

For the sake of troubleshooting and using this guide to assist you, you should look at your heat level setting to see which

light is ashing.

• Disconnect the power cord before performing any maintenance! NOTE: Turning the ON/OFF Switch to ”OFF” does

not disconnect all power to the electrical components of the stove.

• Never try to repair or replace any part of the stove unless instructions for doing so are given in this manual. All other

work should be done by a trained technician.

Display is Flashing “E1”

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. The convection blower is overheating and

tripping the internal temperature shutoff.

Clean any dust off of the windings and fan blade. If

oiling the blower does not help, the blower may be

bad.

2. The stove is being left on the highest setting for

extended periods of time.

If operating the heater on the highest heat setting,

the room temperature could increase enough

and lead to potential overheating situations. If this

happens try operating at a lower heat setting.

3. Fuel other than wood pellets is being burned in

the stove.

This pellet stove is designed and tested to use wood

pellets. Check for signs of fuel other than wood

pellets. No other types of fuel have been approved

for this pellet stove. If there are signs of other types of

fuel being used, stop using them immediately.

4. Power surge or brown out situation.

A power surge, spike, or voltage drop could cause

the high limit switch to trip. Check to see if a

surge protector is being used on the stove. If not,

recommend one to the customer.

5. High Limit Switch is malfunctioning.

If the other items check out OK, replace the high limit

switch.

ATTENTION: This wood heater needs periodic inspection and repair for proper operation. It is against federal

regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual.

Trouble Shooting Guide

Display is Flashing “E2”

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. Airow switch hose or stove attachment

pipes for hose are blocked.

Unhook air hose from the air switch and blow through it.

If air ows freely, the hose and tube are ne. If air will not

ow throw the hose, use a wire coat hanger to clear the

blockage.

2. The air inlet, burnpot, interior combustion air

chambers, combustion blower, or exhaust

pipe are blocked with ash or foreign material.

Follow all cleaning procedures in the maintenance

section of the owner’s manual.

3. The rebox is not properly sealed.

Make sure the door is closed and that the gasket is in

good shape.

4. Vent pipe is incorrectly installed.

Check to make sure vent pipe installation meets criteria

in owner’s manual.

5. The airow switch wire connections are bad.

Check the connectors that attach the gray wires to the

air switch.

6. Combustion blower failure.

With the stove on, check to see if the combustion blower

is running. If it is not, you will need to check for power

going to the combustion blower. It should be a full

current. If there is power, the blower is bad. If there is

not, see #8.

7. Control board not sending power to

combustion blower.

If there is no current going to the combustion blower,

check all wire connections. If all wires are properly

connected, you have a bad control board.

8. Control board not sending power to air

switch.

There should be a 5-volt current (approximately) going to

the air switch after the stove has been on for 30 seconds.

9. Air switch has failed.

To test the air switch, you will need to disconnect the

air hose from the body of the stove. With the other end

still attached to the air switch, very gently suck on the

loose end of the hose (you may want to remove the

hose entirely off the stove and the air switch rst and

make sure it is clear). If you hear a click, the air switch

is working. BE CAREFUL TOO MUCH VACUUM CAN

DAMAGE THE AIR SWITCH.

Trouble Shooting Guide

Display is Flashing “E3”

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. The hopper is out of pellets Rell the hopper.

2. The air dampener is too far open for a low

feed setting

If on the low setting, you may need to close the

dampener all the way.

3. The burnpot holes are blocked. Remove the burnpot and thoroughly clean it.

4. The air inlet, the interior chambers, or exhaust

system has a partial blockage.

Follow all cleaning procedures in the maintenance

section of the owner's manual

5. The hopper safety switch has failed or hopper

is open.

When operating the unit, be sure the hopper lid is

closed so that the hopper safety switch will activate.

Check the wires leading from the hopper safety switch

to the control panel and auger motor for secure

connections. Use a continuity tester to test the hopper

safety switch; replace if necessary.

6. The auger shaft is jammed.

"Start by emptying the hopper. Then remove the auger

motor by removing the auger pin, then remove the two

bolts that hold the auger bracket to the auger tube.

The auger bracket will now be able to be removed

form the auger tube. Remove the two bolts on the side

of the auger tube to remove the lower bearing of the

auger. Pull the auger out of the tube to free the jam.

7. The auger motor has failed.

Remove the auger motor from the auger shaft and try

to run the unit. If the motor will turn the shaft is jammed

on something. If the motor will not turn, the motor is

bad.

8. The Proof of Fire (POF) thermodisc has

malfunctioned.

Temporarily bypass the POF thermodisc by

disconnecting the two wires and connecting them

with a short piece of wire. Then plug the stove back

up. If the stove comes on and works, you need to

replace the POF thermodisc. This is for testing only. DO

NOT LEAVE THE THERMODISC BYPASSED. Your blowers

will never shut off and if the re went out the auger will

continue to feed pellets until the hopper is empty if

you leave the POF thermodisc bypassed.

9. The control board is not sending power to

the POF thermodisc or other auger system

components.

There should be a 5-volt (approximately) current going

to the POF thermodisc after the stove has been on for

10 minutes.

Trouble Shooting Guide

Display is Flashing “E4”

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. The air inlet, burnpot, interior combustion air

chambers, combustion blower, or exhaust pipe

are blocked with ash or foreign material.

Follow all cleaning procedures in the maintenance

section of the owner’s manual.

2. The Proof of Fire (POF) thermodisc has came

unplugged

Check the (POF) thermodisc to see if the wires are

connected properly.

3. The Proof of Fire (POF) thermodisc has

malfunctioned.

Temporarily bypass the POF thermodisc by

disconnecting the two wires and connecting them

with a short piece of wire. Then plug the stove back

up. If the stove comes on and works, you need to

replace the POF thermodisc. This is for testing only.

DO NOT LEAVE THE THERMODISC BYPASSED. Your

blowers will never shut off and if the re went out the

auger will continue to feed pellets until the hopper

is empty if you leave the POF thermodisc bypassed.

4. The hopper is out of Pellets. Rell the hopper.

5. The hopper safety switch has failed or hopper is

open.

When operating the unit, be sure the hopper lid is

closed so that the hopper safety switch will activate.

Check the wires leading from the hopper safety

switch to the control panel and auger motor for

secure connections. Use a continuity tester to test

the hopper safety switch; replace if necessary.

6. The auger shaft is jammed.

Start by emptying the hopper. Then remove the

auger motor by removing the auger pin. Remove

the auger shaft inspection plate in the hopper so that

you can see the auger shaft. Gently lift the auger

shaft straight up so that the end of the auger shaft

comes up out of the bottom auger bushing. Next,

remove the two nuts that hold the top auger biscuit

in. Then rotate the bottom end of the auger shaft

up towards you until you can lift the shaft out of the

stove. After you have removed the shaft, inspect it

for bent ights, burrs, or broken welds. Remove any

foreign material that might have caused the jam.

Also, check the auger tube for signs of damage

such as burrs, rough spots, or grooves cut into the

metal that could have caused a jam.

7. The auger motor has failed.

Remove the auger motor from the auger shaft and

try to run the unit. If the motor will turn the shaft is

jammed on something. If the motor will not turn, the

motor is bad.

Display is Flashing “E5”

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. The stove automatically ashes "E5" when turned

The T-stat sensor has come unplugged form

the control board. Check to see if the sensor is

unplugged. If the sensor is not unplugged then the

sensor is damaged or has a short. If the sensor is

damaged or has a short it will need to be replaced.

Trouble Shooting Guide

Stove Feeds Pellets, But Will Not Ignite

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. Air damper open too far for ignition.

Push the air damper in closer to the side of the stove

for startup. In some situations it may be necessary to

have the damper completely closed for ignition to

take place. After there is a ame, the damper can

then be adjusted for the desired feed setting.

2. Blockage in igniter tube or inlet for igniter tube.

Find the igniter housing on the backside of the rewall.

The air intake hole is a small hole located on bottom

side of the housing. Make sure it is clear. Also, look

from the front of the stove to make sure there is not any

debris around the igniter element inside of the igniter

housing.

3. The burnpot is not pushed completely to the

rear of the rebox.

Make sure that the air intake collar on the burnpot is

touching the rear wall of the rebox.

4. Bad igniter element.

Put power directly to the igniter element. Watch the

tip of the igniter from the front of the stove. After

about 2 minutes the tip should glow. If it does not, the

element is bad.

5. The control board is not sending power to the

igniter.

Check the voltage going to the igniter during startup.

It should be a full current. If the voltage is lower than

full current, check the wiring. If the wiring checks out

good, the board is bad.

Smoke Smell Coming Back Into The Home

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. There is a leak in the vent pipe system.

Inspect all vent pipe connections. Make sure they are

sealed with RTV silicone that has a temperature rating

on 500 degree F or higher. Also, seal joints with UL-

181-AP foil tape. Also, make sure the square to round

adapter piece on the combustion blower has been

properly sealed with the same RTV.

2. The gasket on the combustion blower has

gone bad.

Inspect both gaskets on the combustion blower to

make sure they are in good shape.

Because it is a wood-burning device, your pellet heater may emit a faint wood-burning odor. If this

increases beyond normal, or if you notice an unusual soot build-up on walls or furniture, check your exhaust

system carefully for leaks. All joints should be properly sealed. Also clean your stove, following instructions in

“MAINTENANCE”. If problem persists, contact your dealer.

Convection Blower Shuts Off And Comes Back On

Possible Causes Possible Remedies: (Unplug stove rst when possible)

1. The convection blower is overheating and

tripping the internal temperature shutoff.

Clean any dust off of the windings and fan blades. If

cleaning the blower does not help, the blower may be

bad.

2. Circuit board malfunction.

Test the current going to the convection blower. If

there is power being sent to the blower when it is

shut off, then the control board is ne. If there is NOT

power being sent to the blower when it shuts off during

operation, then you have a bad control board.

Trouble Shooting Guide

La page charge ...

US Stove Company 5501S Manuel utilisateur

Marque: US Stove Company

Modèle: 5501S

Catégorie: Poêles

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: US Stove Company 5501S User manual

Documents connexes

US Stove Company 5501S Le manuel du propriétaire

US Stove Company 5501S Manuel utilisateur

US Stove Company 5501S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents