Marvel MO24FAS1LS1 Mode d'emploi

Marque: Marvel

Modèle: MO24FAS1LS1

Taper: Mode d'emploi

Outdoor Freezers

Congélateurs

d'extérieur

MO24FA

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

NOTE

CAUTION

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product Dimensions ...........................................................8

Starting your appliance ..................................................10

Using your Electronic control ............................................10

Turning your appliance "ON" or "OFF" ..........................10

Setting the temperature ................................................10

Alarms ...........................................................................10

Door ajar ...................................................................10

Temperature sensor fault ..........................................10

High and Low Temperature alarm ............................10

Alarm mute ...................................................................11



Care and cleaning .............................................................14

Stainless steel maintenance ............................................16

Energy saving tips ............................................................16

Obtaining service .............................................................17

Troubleshooting ................................................................18

Warranty ...........................................................................19

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

Death or serious injury could result if...

NOTE

CAUTION

XXXXXXXXXXXX

UNPACKING YOUR APPLIANCE

WARNING

WARNING - Help Prevent Tragedies



the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• 

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can



MARVEL

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left



WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

Online registra-

tion available at

www.marvelrefrig-

eration.com

CAUTION

Front Grille

Do not obstruct the front grille. The openings within the

-



energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use





Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

-

mended installation location temperature range is from 55



Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed.

Leveling Legs

Adjustable legs at the front and rear corners of the appli-



-

all height of your Marvel appliance may be adjusted be-

tween the minimum, 33

4

leg in (CW ↷

4

the leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid





lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete



INSTALLING YOUR APPLIANCE

NOTE

Figure 6

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power



• 

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-



not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Front grille screw

Front grille

Figure 5

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

CAUTION

NOTE

Floor Mount Installation



right rear corner of the freezer as shown in Figure 7.

Step by step instructions for locating the

position of the bracket:







anti-tip bracket.





allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.





where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then



of the cabinet, excluding the door. Slide the freezer out of

the way. From the temporary line extend the sidewall line

back 21

2



the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

2









cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW



material to avoid damage when moving the unit.





Anti-Tip Device

WARNING

If your freezer is not located under a counter top (free



per these instructions. If the freezer is removed from

its location for any reason, make sure that the device

is properly engaged with the anti-tip bracket when

you push the freezer back into the original location. If

the device is not properly engaged, there is a risk of

the freezer tipping over, with the potential for property

damage or personal injury.

Bottom View of

Freezer

Anti-Tip

Bracket

Leveling Leg

Front of cabinet

2"



Figure 7

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

2"



"V" notches

in bracket

"V" notches

in bracket

Side of cabinet line

Figure 8

Front of cabinet line

Rear of cabinet line

Rear Leveling leg

Screw

Figure 8a

NOTE

-

mum adjusted height of the cabinet is increased by

8

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for



PRODUCT DIMENSIONS

Figure 9

Figure 9a

Figure 10

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MO24FAS

24"



**34" to 35"



8"



4" to 34

4"



32"



32"



32"



4"



"F"

2"



* Depth dimension of rough-in opening may vary depend-

ing on each individual installation. To recess entire door "F"



is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 11

WARNING

Floor mount Anti-tip Bracket must be installed for freestand-

ing applications. Not required for built in applications.

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MO24FAS 115V/60Hz/15A

140 lbs



USING YOUR ELECTRONIC CONTROL

Starting your freezer

Plug the freezer power cord into a wall outlet. Your freezer

will begin cooling after power is applied.

If your freezer does not start, check that the freezer is

turned on and the set temperature is cold enough.

Turning your freezer ON or OFF

If the freezer is on, the freezer temperature will be shown





on the display.

If the freezer is not on, "OFF" will be shown on the display.

To turn the freezer on, press and hold the "ON/OFF" but-



shown on the display.

Set temperature

To set the freezer temperature, press and hold the "SET"

button. When the "SET" button is pressed, the display will

show the set temperature. While holding the "SET" button,

press the "WARMER" or "COLDER" buttons to adjust set

temperature.

Freezer operation

The available temperature range of the freezer is -10°F

 to 10°F 

It may take up to 24 hours for your freezer to reach desired

temperature. This will depend on amount of content loaded

and number of door opening and closings.

For best results allow freezer to "pull down" to desired set

temperature before loading. Once contents are loaded,

allow at least 48 hours for temperature to stabilize before

making any adjustments to the set temperature.

Set

Colder Warmer

ON/OFF

Press and Hold Press and Hold

Alarm

Figure 12

close-up of

control

• Temperature Sensor Fault: If the control-

ler detects that the temperature sensor is

not properly functioning, a temperature





at the top left of the display below the word "Alarm" will be

illuminated. Please call Marvel Customer Service or your

dealer if this error code is displayed.

• High and Low Temperature Alarm: If the

storage compartment temperature deviates

excessively from the set-point temperature, the



-

pending upon the condition and the Alarm LED

light at the top left of the display below the word

"Alarm" will be illuminated. The alarm will remain active

until the condition is corrected.

Alarms

Your electronic control will monitor freezer function and

alert you with a series of audible and visual alarms.

• Door Ajar Alarm: If the door has been left







the top left of the display below the word "Alarm" will be il-

luminated. This will stop as soon as the door is closed.

Figure 13

USING YOUR ELECTRONIC CONTROL

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

NOTE

Alarm Mute

Press any key to mute the audible portion of an alarm.

This action will only mute the alarm. If the condition that

caused the alarm continues, the alarm code will continue to



Figure 14

SHELVING CONFIGURATIONS

Freezer:

Loading Tips and Suggestions

Your appliance is equipped with a cantilever shelf and

basket system which provides maximum adjustability and

customizing of the storage arrangements listed below.

24" (61 cm) Wide Models:

Shown with a solid door. Figure 14.





metal shelf.

Figure 15

Perforated metal shelf

To remove the basket:

Press this tab on each

side of the basket slide

and pull the basket out

of the slides.

To install the basket:

Insert the basket slides into the ends of the cabinet

slides and push the basket completely closed. The

slide members will automatically lock together.

Figure 16

Figure 16a

To install or remove a shelf:

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure



insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Rear tang



shelf

Shelf support

slot

Installed shelf

tang

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

CAUTION

Grasp the shelf by the front with

both hands and rotate the front

of the shelf up, then lift the shelf

up and remove the shelf from the

shelf ladders.

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

SHELVING CONFIGURATIONS

Figure 17a

Figure 17

Figure 17b

CARE AND CLEANING

Front Grille

-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see



SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the



temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one



of the LED.

CAUTION

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

CARE AND CLEANING

Outdoor Product Long-Term Storage / Winter-

ization:

1. Time to Winterize, when the daily low ambient tempera-



CAUTION

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

2. 

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

6. It is also recommended that the power to the outlet be



during the Winter season.

7. When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

8. 

brush and vacuum to clean dirt and debris from be-

neath the unit.

9. Thoroughly clean the toe-grille and re-install on the



10. 

use a brush and vacuum to clean dirt and debris from

the machine compartment.

11. Thoroughly clean the rear access cover and re-install

on the unit.

12. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

13. Leave the door open and allow to completely dry out

before closing the door.

14. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

15. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners or

scouring pads. See "Stainless Steel Maintenance" on

page 16.

16. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

17. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

Start-Up After Long-Term Storage:

1. If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

2. Connect the unit to electrical power.

3. 

4. Allow 24-hrs for the unit to stabilize before loading

contents.

Figure 18

Grille

Spacer

Clean out

behind

grille

Figure 19

Soak up

water from

plastic drain

pan if

necessary

Clean out

debris

Remove screws

around perimeter

of access cover.

18. Do not place a cover on the unit, as this can trap con-

densation.

After completion of the above, you may choose to store the

unit indoors, although this is not required.

Remove screw from

each end of grille

Access cover

Background

Stainless steel does not stain, corrode, or rust as easily as

ordinary steel, but it is not stain or corrosion proof. Stain-

less steels can discolor or corrode if not maintained prop-

erly.



amount of chromium present. It is this chromium that





surface can be damaged or contaminated, which may

result in discoloration, staining, or corrosion of the base

metal.

Care & Cleaning

Routine cleaning of the stainless steel surfaces will serve to

greatly extend the life of your product by removing contami-

nants. This is especially important in coastal areas which

can expose the stainless to severe contaminants such as



It is strongly recommended to periodically inspect and thor-

oughly clean crevices, weld points, under gaskets, rivets,

bolt heads, and any locations where small amounts of liquid

could collect, become stagnant, and concentrate contami-

nates. Additionally, any mounting hardware that is showing

signs of corrosion should be replaced.

Frequency of cleaning will depend upon the installation

location, environmental, and usage conditions.

Choosing a Cleaning Product

The choice of a proper cleaning product is ultimately that

of the consumer, and there are many products from which

to choose. Depending upon the type of cleaning and the

degree of contamination, some products are better than

others.



cleaning of most stainless steel products is to give the sur-

faces a brisk rubbing with a soft cloth soaked in warm water

and a gentle detergent, or mild mixture of ammonia. Rub-

bing should, to the extent possible, follow the polish lines of

the steel, and always insure thorough rinsing after cleaning.

Although some products are called "stainless steel clean-

ers," some may contain abrasives which could scratch the



and some many contain chlorine bleach which will dull,

tarnish or discolor the surface if not completely removed.

After the stainless surfaces have been thoroughly cleaned,

a good quality car wax may be applied to help maintain the



Stainless steel products should never be installed, or stored

in close proximity to chlorine chemicals.

Whichever cleaning product you chose, it should be used

in strict accordance with the instructions of the cleaner

manufacturer.

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance



heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not



5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.



appliance requires the door to be open for an extended

period of time.

Energy saving tips:

NOTE

STAINLESS STEEL MAINTENANCE AND ENERGY SAVING TIPS

If Service is Required:

• 

please contact your dealer or call Marvel Customer

Service at 800.223.3900 for directions on how to obtain

warranty coverage in your area.

• 

Marvel Customer Service can provide recommenda-

tions of service centers in your area. A listing of autho-

rized service centers is also available at www.marvelre-

frigeration.com under the service and support section.

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "A" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service Number

Date Warranty Card Sent (Must



Table A

OBTAINING SERVICE

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read through

-

shooting guide below. Locate the problem in the guide and

refer to the cause and its remedy before calling for service.

The problem may be something very simple that can be

solved without a service call. However, it may be required



TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough



• Control set too warm

• Content temperature not stabilized.

• Excessive usage or prolonged door open-

ings.

• 

• Door gasket not sealing properly.

• Adjust temperature colder. Allow 24 hours

for temperature to stabilize.

• Allow temperature to stabilize for at least

24 hours.

• 



page 4.

• Replace door gasket.

Appliance too cold



• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Replace door gasket.

No interior light. • Failed LED light assembly or light switch. • 

Light will not go out when door is closed • Door not activating light switch.

• Failed light switch

• Appliance not level, level appliance, (See



• 

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• 

page 4.

• 

Appliance will not run. • 

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting your ap-



• Plug in power cord.

• Check house circuit.

NOTE



Because of this the storage compartment has an almost air

tight seal. Therefore when accessing contents and closing

the door, the warm air intrusion will collapse due to the cold

compartment temperature creating a slight vacuum inside

the unit. This may make the door harder to open for about

10 seconds until the internal pressure equalizes with the

exterior.

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call



that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused





NOTE

Your product has an automatic defrost feature that utilizes

an electric heater element. Periodically during defrost you

may observe the following:

• Water dripping and running sounds as a result of the

frost melt.

• Sizzling and popping sounds from water dripping on

the heater element.

• A faint reddish glow in the freezer compartment from

the electric heater element.



refrigeration product incorporating automatic defrost. They

do not represent any product fault or safety issue.

Marvel Refrigeration (Marvel) Limited Warranty

ONE YEAR LIMITED PARTS & LABOR WARRANTY

For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the

product that proves to be defective in materials or workmanship. For products installed and used for normal residential use,

material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.

All service provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless



TWO YEAR LIMITED PARTS & LABOR WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For two years from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the

product that proves to be defective in materials or workmanship. For products installed and used for normal residential use,

material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.

All service provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless

AVAILABLE THIRD YEAR LIMITED WARRANTY (MARVEL PROFESSIONAL PRODUCTS)



of purchase, free of charge. To take advantage of this third year warranty, you must register your product with Marvel within 60

days from the date of purchase at marvelrefrigeration.com and provide proof of purchase.

LIMITED FIVE YEAR SEALED SYSTEM WARRANTY



to be defective in materials or workmanship: compressor, condenser, evaporator, drier, and all connecting tubing. All service

provided by Marvel under the above warranty must be performed by a Marvel factory authorized servicer, unless otherwise



WARRANTY TERMS



or the ten provinces of Canada. The warranties do not cover any parts or labor to correct any defect caused by negligence,



product must be installed, operated, and maintained in accordance with the Marvel User Guide.

The remedies described above for each warranty are the only ones that Marvel will provide, either under these warranties or

under any warranty arising by operation of law. Marvel will not be responsible for any consequential or incidental damages

arising from the breach of these warranties or any other warranty, whether express, implied, or statutory. Some states do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to



Any warranty that may be implied in connection with your purchase or use of the product, including any warranty of





limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

• The warranties only apply to the original purchaser and are non-transferable.

• These warranties cover products installed and used for normal residential use only.

• The warranties apply to units operated outside only if designed for outdoor use by model and serial number.

 

• The start of Marvel’s obligation is limited to four years after the shipment date from Marvel.

• In-home instruction on how to use your product is not covered by these warranties.

• Food, beverage, and medicine loss are not covered by these warranties.

• If the product is located in an area where Marvel factory authorized service is not available, you may be responsible for a

trip charge or you may be required to bring the product to a Marvel factory authorized service location at your own cost and

expense.

 

only and no coverage is provided for cosmetic defects.

• Signal issues related to Wi-Fi connectivity are not covered by these warranties.

For parts and servi

MarvelRefrigeration.com • [email protected] • +616.754.5601

1260 E. Van Deinse St., Greenville, MI 48838

HOUSEHOLD PRODUCT WARRANTY



the buyer to corresponding changes, improvements, additions, replacements or compensation for

previously purchased products.

www.marvelrefrigeration.com

1260 E. VanDeinse St.

Greenville MI 48838

800.223.3900

41014505-EN Rev D

1/15/20

Marvel Refrigeration

La page est en cours de chargement...

Marvel MO24FAS1LS1 Mode d'emploi

Marque: Marvel

Modèle: MO24FAS1LS1

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel MO24FAS1LS1 User guide

Marvel MO24FAS1LS1 Mode d'emploi

Marvel MO24FAS1LS1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents