Samsung NE63T8111SG Guide d'installation

Electric Range

Installation manual

NE63*8*****

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 1 2020-03-26  6:27:49

2 English

Contents

Before you begin 2

Anti-tip device 2

About this manual 2

For your safety 3

Preparing to install the range 3

Prepare tools & Parts 3

Checking the installation site 4

To avoid breakage 6

Connecting the power 7

Step 1. Meeting electrical connection requirements 7

Step 2. Accessing the power cord connection 8

Step 3. Installing the power cord 9

Step 4. Installing the conduit 11

Step 5. Replacing the access cover 13

Installing the range 13

Installing the anti-tip device 13

Finalizing the installation 15

Before you begin

Anti-tip device

WARNING

To reduce the risk of tipping the appliance, the appliance must be secured by

properly installed anti-tip devices packed with the appliance.

A. A child or adult can tip the range and be killed.

B. Install the anti-tip device to the structure and/or the

range at rear right (or rear left) of the range bottom.

C. Engage the range to the anti-tip device by leveling leg

at rear right (or rear left) of the range bottom.

D. Re-engage the anti-tip device if the range is moved.

E. See installation instructions for details.

F. Failure to do so can result in death or serious burns to

children or adults.

About this manual

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

Important note to the installer

• Read all instructions contained in these installation instructions before

installing the range.

• Remove all packing materials from the oven compartments before connecting

the electrical supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 2 2020-03-26  6:27:49

English 3

Before you begin

Important note to the consumer

Keep these instructions for the local electrical inspector’s use.

• As when using any appliance generating heat, there are certain safety

precautions you should follow.

• Be sure your range is installed and grounded properly by a qualied installer

or service technician.

• For the range to ventilate properly, make sure the range’s vents are not

blocked or covered, and that there is enough clearance at the top, back, sides,

and underneath the range. The vents allow the necessary exhaust for the

range to operate properly with correct combustion and get the good cooking

result.

• Make sure the wall coverings around the range can withstand the heat

generated by the range.

• To eliminate the need to reach over the surface elements, avoid having cabinet

storage space above the cooktop.

• The range should not be placed on a base.

For your safety

WARNING

• If the information in this manual is not followed exactly, a re or electrical

shock may result causing property damage, personal injury, or death.

• Before beginning the installation, switch the power off at the service panel and

lock the service disconnecting switch to prevent power from being switched

on accidentally. When the service disconnecting switch cannot be locked,

securely fasten a prominent warning device, such as a tag, to the service panel.

• This appliance must be properly grounded.

Preparing to install the range

Prepare tools & Parts

The tools you will need

Drill Adjustable Wrench Pliers

1

⁄4" Nut Driver

Phillips Screwdriver Flat Screwdriver Pencil Level

What’s included with your range

Anti-tip Bracket

Template

Anti-Tip Bracket Screws (short:2 ea,

long:2 ea)

Filler Kit

Additional materials you may need

4-Wire Cord or 3-Wire Cord

(UL Approved 40 or 50 AMP)

Strain Relief

(For Conduit Installation Only)

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 3 2020-03-26  6:27:50

4 English

Preparing to install the rangePreparing to install the range

Preparing to install the range

36 in

(914.4 mm) Min.

36

3

/4 in

(933.45 mm) Max.

29

15

/16 in

(761.0 mm)

26

7

/

16

in

(671.7 mm)

49

1

/

4

in (1250.3 mm)

Door fully open

28

11

/

16

in

(728.6 mm)

With handle

Checking the installation site

Clearances and dimensions

To install the range, refer to the following gure.

CAUTION

This range has been designed to comply with the maximum allowable wood

cabinet temperatures of 194 °F. Make sure the wall covering, countertops, and

cabinets around the range can withstand the heat (up to 194 °F) generated by the

range. If not, discoloration, delamination, or melting may occur.

A

B

36"-36

3

⁄4"

29

3

⁄4"

26

7

⁄16"

49

1

⁄4"

28

11

⁄16"

29

15

⁄16"

35

7

⁄8"

25"

24"

6"

3"

24"

3"

A : Cabinet opening min 30" (76.2 cm)

B : Acceptable electrical outlet area

IMPORTANT: If your cabinets are over 36

3

⁄4" high, you must install this range on a

hard, heat resistant support that raises the surface of the range so that it is about

even with the countertop.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 4 2020-03-26  6:27:50

English 5

Preparing to install the range

CAUTION

You must use the rear ller kit to install the range in a freestanding cutout cabinet.

For more information, see “Optional rear ller kit” as shown below.

NOTE

If you install the product in a kitchen island, you must maintain minimum 2-1/2"

from cutout to back edge of the countertop and minimum 3" from cutout to side

edges of the countertop.

Optional rear ller kit

Used to ll gap between the range back and wall. Adds a ller strip to the rear

of the range. This kit can only be used when the opening in the countertop is 25"

deep.

1. Unscrew the screws afxing the vent cover.

2. Assemble the ller strip to the back of the range using the removed screws.

NOTE

If the countertop depth is greater than 25", there will be a gap between the ller

kit and the back wall.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 5 2020-03-26  6:27:50

6 English

Preparing to install the rangePreparing to install the range

Preparing to install the range

To avoid breakage

CAUTION

Do NOT lift or handle the unit by the cooktop glass or door handle.

Fig. 1

C1

C3

C2

C4

1. The counter top around the cut-out should be at and leveled.

2. Before installing the unit, measure the heights of the two cabinet sides (C1-C4),

front and back (See Fig. 1) from the oor to the top of the counter.

3. Level the range using the four leveling legs so that the height from the oor

to the underside of the cooktop glass frame is greater than the tallest cabinet

measurement by at least

1

⁄16".

4. Slide the unit into the cabinet (DO NOT PUSH THE UNIT HARD). Make sure the

center of the unit aligns with the center of the cabinet cut-out.

Minimum dimensions

IMPORTANT: To eliminate the risk of burns or re caused by reaching over heated

surface units, avoid having cabinet storage space located above the surface units.

If you have cabinet storage space over the heating elements, you can reduce the

risk by installing a range hood that projects horizontally a minimum of 5 inches

beyond the bottom of the cabinets.

30"

* 30"

** 15"

* A minimum of 30" is required between the top of the cooking surface and the

bottom of an unprotected wood or metal cabinet; a minimum of 24" is required

if the bottom of the wood or metal cabinet is protected by not less than

1

⁄4" of

ame retardant millboard covered with not less than no.28 MSG of sheet steel,

0.015" of stainless steel, 0.024" of aluminum, or 0.020" of copper.

** A minimum of 15" is required between the countertop and the adjacent cabinet

bottom.

CAUTION

Vapors may come out from the vent. It is normal, but be careful as it may be hot.

Depending on the material of your wall, hot vapors may leave stains on it.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 6 2020-03-26  6:27:50

English 7

Connecting the power

Step 1. Meeting electrical connection requirements

CAUTION

For personal safety, do not use an extension cord with this appliance. Remove the

house fuse or open the circuit breaker before beginning installation.

This appliance must be supplied with the proper voltage and frequency, and be

connected to an individual, properly grounded branch circuit, protected by a

circuit breaker or fuse having amperage as specied on the rating plate. The rating

plate is located on the bottom side of the control panel.

We recommend you have the electrical wiring and hookup of your range

connected by a qualied electrician. After installation, have the electrician show

you where your main range disconnect is located.

Check with your local utilities for electrical codes which apply in your area. Failure

to wire your oven according to governing codes could result in a hazardous

condition. If there are no local codes, your range must be wired and fused to meet

the requirements of the National Electrical Code, ANSI/NFPA No. 70–Latest Edition.

You can get a copy by writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National Electrical Code requires that new

construction (not existing) utilize a 4-conductor connection to an electric range.

When installing an electric range in new construction, follow Steps 2 and 3 for a

4-wire connection.

You must use a 3-wire or 4-wire, single-phase A.C. 208Y/120 Volt or

240/120 Volt, 60 hertz electrical system.

If the electrical service provided does not meet the above specications, have a

licensed electrician install an approved outlet.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be

provided with ring terminals on the wire and a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range is required.

A 50 amp range cord is not recommended but if used, it should be marked for

use with nominal 1

3

⁄8" diameter connection openings. Care should be taken to

center the cable and strain relief within the knockout hole to keep the edge from

damaging the cable.

• Because range terminals are not accessible after the range is in position, a

exible service conduit or cord must be used.

NOTE

If the power connection is plugged in improperly, the following message appears

on the display.

• LCD, PMOLED : Wire installation fail

• LED : bAd LinE

Reconnect the power connection properly, and the message disappears.

ALL NEW BRANCH-CIRCUIT CONSTRUCTIONS, MOBILE HOMES,

RECREATIONAL VEHICLES, AND INSTALLATIONS WHERE LOCAL

CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL, REQUIRE

A 4-CONDUCTOR UL-LISTED RANGE CORD.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 7 2020-03-26  6:27:50

8 English

Connecting the powerConnecting the power

Connecting the power

Step 2. Accessing the power cord connection

Loosen and then remove the rear access cover screw with a screwdriver. Remove

the rear access cover by pull right and then out. The terminal block will then be

accessible.

Terminal block

Access cover

Specied rating of power-supply-cord kit and circuit protection

Range rating, watts

Specied rating

of power-supply-

cord kit and

circuit protection,

Amps

Diameter (inches) of range

connection opening

120/240 volts

3-wire

120/208 volts

3-wire

Power cord Conduit

8750-16500 7801-12500 40 or 50 A 1

3

⁄8" 1

1

⁄8"

This appliance must be supplied with the proper voltage at the proper frequency

and must be connected to a dedicated, properly grounded branch circuit protected

by a 40 amp or larger circuit breaker.

NOTE

For power cord installations, go to Step 3. For conduit installations, go to Step 4 on

page 11.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 8 2020-03-26  6:27:51

English 9

Connecting the power

Step 3. Installing the power cord

For power cord installations, hook the strain relief over the power cord hole (1

3

⁄8")

located below the rear of the drawer body. Insert the power cord through the

strain relief and tighten the device.

Conduit

connection

plate

Power

cord

Strain relief

• You must install the power cord with a strain relief.

• Attach the strain relief to the 1

3

⁄8" opening in the conduit connection plate.

Installing a 3-wire power cord

WARNING

The neutral or ground wire of the power cord must be connected to the neutral

terminal located in the center of the terminal block. The power leads must be

connected to the lower left and the lower right terminals of the terminal block.

1. Remove the 3 lower terminal screws from the terminal block.

2. Insert the 3 terminal screws through each power cord terminal ring and into

the lower terminals of the terminal block. Be certain that the center wire

(white/neutral) is connected to the center lower position of the terminal block.

3. Tighten screws securely to the terminal block. DO NOT remove the ground

strap connection.

4. Go to Step 5 on page 13 to continue with the installation.

Neutral terminal

Live 1

Ground strap

Live 2

Black

White

Red

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 9 2020-03-26  6:27:51

10 English

Connecting the powerConnecting the power

Connecting the power

CAUTION

You must check voltage after connecting power cord.

Live 1 - Neutral 120 V

Live 2 - Neutral 120 V

Live 1 - Live 2 208 V / 240 V

Installing a 4-wire power cord

WARNING

The neutral wire of the supply circuit must be connected to the neutral terminal

located in the lower center of the terminal block. The power leads must be

connected to the lower left and the lower right terminals of the terminal block. The

4th grounding lead must be connected to the frame of the range with the ground

plate and the ground screw.

1. Remove the 3 lower terminal screws from the terminal block. Remove the

ground screw and ground plate and retain them.

2. Cut and discard the ground strap. Do not discard any screws.

3. Insert the ground screw into the power cord ground wire terminal ring,

through the ground plate, and into the frame of the range.

4. Insert the 3 terminal screws (removed earlier) through each power cord

terminal ring and into the lower terminals of the terminal block. Be certain that

the center wire (white/neutral) is connected to the center lower position of the

terminal block. Tighten screws securely to the terminal black.

5. Go to Step 5 on page 13 to continue with the installation.

Neutral

terminal

Live 2

Ground wire

(Green)

Ground

screw

Live 1

Ground strap

Ground plate

Black

White

Red

CAUTION

You must check voltage after connecting power cord.

Live 1 - Neutral 120 V

Live 2 - Neutral 120 V

Live 1 - Live 2 208 V / 240 V

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 10 2020-03-26  6:27:51

English 11

Connecting the power

Step 4. Installing the conduit

Remove the conduit connection plate and rotate it as shown below.

The conduit hole (1

1

⁄8") must be used.

1

⁄8"

1

⁄8"1

3

⁄8"

1

3

⁄8"

1. Prepare the conduit cord as shown in Figure 1.

2. Install the conduit cord as shown in Figure 2.

Knockout surface

Conduit connection plate

Strain relief

Ring

Body

Figure 1

3 wire 4 wire

Figure 2

1" 1"

3

⁄8"

3

⁄8"

3

1

⁄2" 3

1

⁄2"

For conduit installations, insert the strain relief (not included) into the conduit

hole (1

1

⁄8"). Then thread the conduit cord through the body of the strain relief and

fasten the ring. Reinstall the bracket.

Installing a 3-wire conduit

• Aluminum building wire may be used but it must be rated for the correct

amperage and voltage. Connect the wires as described below.

• The wire you use, the location and enclosure of splices, etc., must conform to

good wiring practices and local codes.

1. Loosen the 3 lower terminal screws from the terminal block.

2. Insert the center bare wire (white/neutral) tip through the bottom center

terminal block opening. On certain models, the wire will need to be inserted

through the ground strap opening and then into the bottom center block

opening.

3. Insert the two side bare wire tips into the lower left and the lower right

terminal block openings.

4. Tighten the screws until the wire is rmly secured (35 to 50 inch-lbs.). Do not

over-tighten the screws since it could damage the wires.

5. Go to Step 5 on page 13 to continue with the installation.

Ground strap

Live 2

Wire tips

Neutral terminal

Live 1

Black

White

Red

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 11 2020-03-26  6:27:51

12 English

Connecting the powerConnecting the power

Connecting the power

CAUTION

You must check voltage after connecting power cord.

Live 1 - Neutral 120 V

Live 2 - Neutral 120 V

Live 1 - Live 2 208 V / 240 V

Installing a 4-wire conduit

• Aluminum building wire may be used but it must be rated for the correct

amperage and voltage to make the connection. Connect the wires as described

below.

• The wire you use, the location and enclosure of splices, etc., must conform to

good wiring practices and local codes.

1. Loosen the 3 lower terminal screws from the terminal block. Remove the

ground screw and ground plate and retain them.

2. Cut and discard the ground strap. Do not discard any screws.

3. Insert the ground bare wire tip between the range frame and the ground

plate (removed earlier) and secure it in place with the ground screw (removed

earlier).

4. Insert the bare wire (white/neutral) tip through the bottom center of the

terminal block opening.

5. Insert the two side bare wire tips into the lower left and the lower right

terminal block openings.

6. Tighten the screws until the wire is rmly secured (35 to 50 inch-lbs.). Do not

over-tighten the screws since it could damage the wires.

7. Go to Step 5 on page 13 to continue with the installation.

Neutral

terminal

Live 2

Ground

wire (Green)

Wire tips

Ground strap

Ground plate

Black

White

Red

Live 1

CAUTION

You must check voltage after connecting power cord.

Live 1 - Neutral 120 V

Live 2 - Neutral 120 V

Live 1 - Live 2 208 V / 240 V

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 12 2020-03-26  6:27:51

English 13

Installing the range

Installing the anti-tip device

WARNING

To reduce the risk of tipping, you must secure the appliance by properly installing

the Anti-Tip device packed with the appliance.

• Refer to the installation instructions supplied with the bracket.

• If the anti-tip device is not installed properly, an adult or child stepping on or

sitting on the range door could tip the range and suffer serious injuries caused

by spilled hot liquids or by the range itself.

*approximately

21

⁄32" (16.5 mm)

Screw must enter wood or concrete

Anti-Tip

bracket

NOTE

To install the Anti-Tip bracket, release the leveling leg. A minimum clearance of

21

⁄32" (16.5 mm) is required between the range bottom and the kitchen oor.

Step 5. Replacing the access cover

To replace the rear access cover on the range back. Insert the double projections

on the bottom of the cover into the pockets located below the opening, and then

insert and tighten the rear access cover screw.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 13 2020-03-26  6:27:52

14 English

Installing the range

1. Install the bracket using the template

The Anti-Tip bracket is packaged with a template. The instructions include

information necessary to complete the installation. Read and follow the

instructions on the sheet (template) for range installation.

2. Level the range

Level the range by adjusting the leveling legs with a wrench.

Leveling leg

Raise range

Lower range

3. Check your adjustments

Use a spirit level to check your adjustments. Place the level diagonally on the oven

rack or surface cooktop, and conrm the range is level in the two directions shown

below.

1. Check direction 1.

2. Check direction 2.

If the spirit level indicates that the range is not level, adjust the leveling legs with

a wrench.

Ground

CAUTION

For your safety, do not attempt to modify

or straighten front legs. Front leveling legs

on the range are designed to be slanted to

prevent accidental tipping.

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 14 2020-03-26  6:27:52

English 15

Installing the range

Finalizing the installation

• Move range close enough to the opening to plug into the receptacle.

• Slide the range into position ensuring that the rear left (or rear right) leg slides

under the Anti-Tip bracket.

• Carefully tip the range forward to insure that the Anti-Tip bracket engages the

back brace and prevents tip-over.

• Turn on the electrical power. Check the range for proper operation as

described in the user manual.

Anti-Tip

bracket

Leveling leg

Memo

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 15 2020-03-26  6:27:52

Scan the QR code* or visit

www.samsung.com/spsn

to view our helpful

How-to Videos and Live Shows

* Requires reader to be installed on

your smartphone

Please be advised that the Samsung warranty does NOT cover service calls to explain product operation, correct improper installation, or perform normal cleaning or

maintenance.

QUESTIONS OR COMMENTS?

COUNTRY CALL OR VISIT US ONLINE AT

U.S.A

Consumer Electronics

1-800-SAMSUNG (726-7864) www.samsung.com/us/support

CANADA 1-800-SAMSUNG (726-7864)

www.samsung.com/ca/support (English)

www.samsung.com/ca_fr/support (French)

DG68-01257A-00

Install_NE63T8911_AA_DG68-01257A-00_EN.indd 16 2020-03-26  6:27:52

Estufa eléctrica

Manual de instalación

NE63*8*****

Install_NE63T8911_AA_DG68-01257A-00_MES.indd 1 2020-03-26  6:27:38

2 Español

Contenido

Antes de comenzar 2

Dispositivo anti inclinación 2

Acerca de este manual 2

Para su seguridad 3

Preparación para instalar la estufa 3

Prepare las herramientas y las piezas 3

Control del sitio de instalación 4

Para evitar la rotura 6

Cómo conectar la corriente eléctrica 7

Paso 1. Cumplimiento de los requisitos de conexión eléctrica 7

Paso 2. Acceso a la conexión del cable de alimentación 8

Paso 3. Instalación del cable de alimentación 9

Paso 4. Instalación del conducto 11

Paso 5. Colocación de la cubierta de acceso 13

Instalación de la estufa 13

Instalación del dispositivo anti inclinación 13

Finalización de la instalación 15

Antes de comenzar

Dispositivo anti inclinación

ADVERTENCIA

Para reducir el riesgo de inclinaciones, el artefacto debe quedar correctamente jado mediante la

instalación de los dispositivos anti inclinación que vienen con el equipo.

A. Un niño o un adulto podrían inclinar la estufa y morir.

B. Instale el dispositivo anti inclinación en la estructura y/o en la

parte posterior derecha (o posterior izquierda) de la base de la

estufa.

C. Acople la estufa en el dispositivo anti inclinación nivelando las

patas en la parte posterior derecha (o posterior izquierda) de la

base de la estufa.

D. Vuelva a acoplar el dispositivo anti inclinación en caso de mover

la estufa.

E. Consulte las instrucciones de instalación para obtener más

información.

F. No hacerlo puede provocar la muerte o quemaduras serias a niños

o adultos.

Acerca de este manual

LEA ESTAS INSTRUCCIONES EN SU TOTALIDAD Y CUIDADOSAMENTE.

Nota importante para el instalador

• Lea todas las instrucciones contenidas en este manual antes de instalar la estufa.

• Retire de la estufa todos los materiales de empaque de los compartimientos del horno antes de

conectar la alimentación eléctrica a la estufa.

• Cumpla todos los códigos y ordenanzas exigidos por las autoridades pertinentes.

• Asegúrese de dejar estas instrucciones al usuario.

Install_NE63T8911_AA_DG68-01257A-00_MES.indd 2 2020-03-26  6:27:38

Español 3

Antes de comenzar

Nota importante para el usuario

Guarde estas instrucciones para que puedan ser consultadas por el inspector del servicio eléctrico de

su localidad.

• Como con cualquier artefacto que genera calor, existen ciertas precauciones de seguridad que se

deben cumplir.

• Asegúrese de que su electrodoméstico sea correctamente instalado y conectado a tierra por un

técnico calicado.

• Para que la estufa pueda ventilarse correctamente, asegúrese de que las ventilaciones no estén

bloqueadas ni cubiertas, y de que haya suciente espacio libre arriba, atrás, a los lados y por

debajo de la estufa. Las ventilaciones permiten la salida de aire necesaria para que la estufa

funcione adecuadamente con la combustión correcta y se obtengan buenos resultados de

cocción.

• Asegúrese de que los revestimientos de las paredes alrededor de la estufa pueden soportar el

calor que ésta genera.

• Para eliminar la necesidad de alcanzar objetos por encima de los elementos de la supercie,

evite tener gabinetes de almacenamiento sobre la cubierta.

• La estufa no debe colocarse sobre una base.

Para su seguridad

ADVERTENCIA

• Si la información de este manual no es seguida con exactitud, se podrían producir incendios o

descargas eléctricas que causen daños a la propiedad, lesiones personales o la muerte.

• Antes de comenzar la instalación, corte la alimentación eléctrica desde el panel de servicio y

cierre con llave el interruptor de desconexión del servicio para evitar que la corriente eléctrica

sea conectada accidentalmente. Cuando el interruptor de desconexión del servicio no se pueda

bloquear, coloque un dispositivo de advertencia prominente, tal como una etiqueta, en el panel

de servicio.

• Este electrodoméstico debe conectarse a tierra correctamente.

Preparación para instalar la estufa

Prepare las herramientas y las piezas

Las herramientas que necesitará

Taladro Llave ajustable Pinza Llave para tuercas de

1

/4"

Destornillador Phillips Destornillador plano Lápiz Nivel

Elementos incluidos con su estufa

Plantilla de ménsula anti

inclinación

Ménsula anti inclinación Tornillos (cortos: 2,

largos: 2)

Kits de relleno

Materiales adicionales que puede necesitar

Cable de 4 conductores o cable de 3 conductores

(de 40 o 50 AMP aprobados por United

Laboratories, Inc. ("UL")

Sujetador de cables con amortiguador de esfuerzo

(únicamente para instalación con conducto)

Install_NE63T8911_AA_DG68-01257A-00_MES.indd 3 2020-03-26  6:27:39

4 Español

Preparación para instalar la estufaPreparación para instalar la estufa

Preparación para instalar la estufa

36 pulgadas

(914.4 mm) mín.

36

3

/4

pulgadas

(933.45 mm) máx.

29

15

/16 pulgadas

(761.0 mm)

26

7

/

16

pulgadas

(671.7 mm)

49

1

/

4

pulgadas

(1250.3 mm)

Puerta completamente

abierta

28

11

/

16

pulgadas

(728.6 mm)

Con manija

Control del sitio de instalación

Distancias, espacios libres y dimensiones

Para instalar la estufa, observe la gura a continuación.

PRECAUCIÓN

Esta estufa ha sido diseñada para cumplir con la temperatura máxima admisible para gabinetes

de madera de 194 °F. Asegúrese de que los revestimientos de paredes, supercies de mesada y

gabinetes alrededor de la estufa puedan soportar el calor (hasta 194 °F) generado por la estufa. De

lo contrario, se podrían producir alteraciones de color, deslaminación o derretimiento.

A

B

36"-36

3

⁄4"

29

3

⁄4"

26

7

⁄16"

49

1

⁄4"

28

11

⁄16"

29

15

⁄16"

35

7

⁄8"

25"

24"

6"

3"

24"

3"

A: Abertura del gabinete mín. 30" (76.2 cm)

B: Área admisible para toma de corriente

IMPORTANTE: Si sus gabinetes tienen una altura superior a 36

3

⁄4", debe instalar la estufa en un

soporte duro y resistente al calor que levante la supercie de la estufa hasta que quede a nivel con

la mesada.

Install_NE63T8911_AA_DG68-01257A-00_MES.indd 4 2020-03-26  6:27:39

La page est en cours de chargement...

Samsung NE63T8111SG Guide d'installation

Samsung NE63T8111SG Guide d'installation

dans d''autres langues

Documents connexes

Autres documents