Whirlpool WDF550SAHW Guide d'installation

INSTALLATION INSTRUCTIONS

UNDERCOUNTER DISHWASHER

LAVAVAJILLAS EMPOTRADA CON TINA

INSTRUCTIONS D’INSTALLATION

LAVE-VAISSELLE ENCASTRÉ

Table of Contents ........................................................2

Indice

........................................................................21

Table des matières

....................................................40

W11160365C

2

TABLE OF CONTENTS

DISHWASHER SAFETY ................................................... 3

INSTALLATION REQUIREMENTS ................................... 4

Tools and Parts .........................................................................4

18" Product and Cabinet Opening Dimensions ........................6

24" Product and Cabinet Opening Dimensions ........................7

Location Requirements ............................................................. 8

Drain Requirements ..................................................................8

Water Supply Requirements .....................................................8

Electrical Requirements ............................................................8

INSTALLATION INSTRUCTIONS ..................................... 9

Prepare Cabinet Opening—NewUtilities ..................................9

Moisture Barrier—Recommended for Wood Countertops .......9

Direct Wire Routing .................................................................10

Prepare Dishwasher ................................................................10

Remove Access Panel ............................................................11

Connect Elbow to Valve .......................................................... 11

Connect Fill Hose to Elbow ....................................................11

Power Cord Connection .........................................................12

Utility Routing Channel Location ............................................13

Choose Anchor Attachment Method ......................................14

Direct Wire Electrical Connection ...........................................17

Connect Water Line to House Shutoff Valve...........................18

Connect Drain Hose ...............................................................18

Complete Installation ..............................................................20

Reinstall Access Panel ............................................................20

Check Operation .....................................................................20

If Dishwasher Does Not Operate ............................................20

Additional Tips ........................................................................20

3

DISHWASHER SAFETY

You Need to:

■ Slowly open dishwasher door while someone grasps the rear

of the dishwasher. Remove shipping materials and drainhose.

Close dishwasher door until latched.

NOTE: Each dishwasher is tested at the factory and may

contain some residual water in the tub as a result of the test.

■ Observe all governing codes and ordinances.

■ Install this dishwasher as specied in these instructions.

■ Installation should be performed by a qualied servicetechnician.

■ The dishwasher must be installed to meet all electrical

andplumbing national and local codes and ordinances.

Care shall be exercised when the appliance is installed

orremoved, to reduce the likelihood of damage to the

powercord.

WARNING: To reduce the risk of electric shock, re, or injury

to persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

4

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with

thetools listed here.

All Installations

Tools Needed:

Pliers Flat-blade screwdriver

Phillips screwdriver Utility knife

Nipper Small level

Measuring tape or ruler Hex L-wrenches

10" adjustable wrench that

opens to 1

1

/

8

" (29 mm)

Torx

®†

T20

®

screwdriver

†

®

TORX, T15, and T20 are registred trademarks of Acument Intellectual Properties, LLC.

Other Useful Items You May Need:

Flashlight Shallow pan

Bath towel Masking, electrical,

or duct tape

Parts Supplied:

Provided with the dishwasher. Check when you unbox the

dishwasher.

Kick plate

Moisture barrier strip

Cable tie

(for drain hose)

Undercounter mounting

brackets (2)

Adjustment cap (2) ST4 x 14(2)

(for installation bracket)

ST3.9 x 9(2)

(for installation bracket)

ST3.9 x 13(2) (for kick plate)

Make sure all parts are included in the literature package.

If parts are not included, call us at our toll-free number or visit

our website listed in the User Guide.

5

Other Parts Needed (not provided):

Household Wiring (Metallic)

Strain Relief

to t 7/8" (22mm) hole

(required to properly secure

household wiring to the

dishwasher terminal box)

(Whirlpool Part

Number 4396672)

NOTE: Use only UL Listed/

CSA Approved part.

Twist-On Wire Connectors

NOTES:

■ Conrm proper size for

connecting your gauge

of household wiring to

the 16-gauge wiring in

the dishwasher.

■ Use only UL Listed/CSA

Approved parts.

TEFLON

®†

Tape or Sealing

Compound

90° elbow

Tube ttings

(for copper tubing)

Call us at our toll-free number, visit our website listed in the

User Guide for part numbers above, orsee local electrical/

plumbing supply retailer for equivalent.

First-Time Installations

Check local codes. Check existing electrical supply. See the

“Electrical Requirements” section. It is recommended that

electrical connections be made by a licensed electrical installer.

Additional Tools Needed:

Small tubing cutter Wire stripper

†

®

TEFLON is a registered trademark of Chemours.

Cordless drill 1/2", 3/4", and 1

1

/

2

" hole

saw bits

Additional Parts Needed (not provided):

Copper Tubing (3/8" O.D.

suggested) or Flexible

Braided WaterSupply

Line Kit (Whirlpool Part

Number W10278635RP).

Kitincludes braided hose

and 3/8" compression x

3/4"hosetting.

Hose Clamps 1

1

/

2

"- 2"

(38-50 mm) (3maximum)

Call us at our toll-free number, visit our website listed in the

User Guide for part numbers above, orsee local plumbing supply

retailer for equivalent.

NOTE: If using a exible braided hose, replace inlet hose after

5years to reduce the risk of hose failure. Record hoseinstallation

or replacement dates on the hose for futurereference.

For Direct Wire For Power Cord

Cabinet G

rommet

For 1

1

/

2

" (38 mm) hole

in cabinet. (Whirlpool

PartNumber302797)

NOTE: Required for metal

cabine

ts

Power Cord Ki

t

Kit typically includes

power cord, metallic strain

relief,grommet, and twist-on

wi

re connectors. (Whirlpool Part

Number 4317824)

Call us at our toll-free number, visit our website listed in the User

Guide for part numbers above, orsee local electrical supply

retailer for equivalent.

6

32

1

/2"

(82.5 cm) min.

(87.5 cm) max

21

9

/16"

(54.7 cm)

Side View 18" Custom Wood Panel

32

1

/2"

(82.5 cm) min.

(87.5 cm) max

17

5

/8"

(44.7 cm) max

Front View

NOTE: Route the water supply line and power cable through

the channels provided under the dishwasher (circled above).

32

1

/2"

(82.5 cm) min.

(87.5 cm) max

22

7

/16"

(57.0 cm)

22

5

/16"

(56.6 cm)

Side View 18" Metal Door Panel

18"

(45.7 cm) min.

24"

(61 cm)

min.

32

1

/2"

(82.5 cm) min.

Cutout Dimensions

Underside of countertop to oor

The enclosure must be at least 18" (45.7 cm) wide, 24"

(61 cm) deep, and 32½" (82.5 cm) high.

For the front door of the dishwasher to be ush with the

leading edge of the counter top, the counter top must be

at least 24" (61 cm) deep.

This dishwasher is designed to be enclosed on the top and

on both sides by a standard residential kitchen cabinet unit.

The installation enclosure must be clean and free of any

obstructions.

NOTE: ADA installation, 32½" (82.5 cm) beneath 34"

(86.4 cm) high countertops may be accomplished by

adjusting the toekick and leveling legs.

18" PRODUCT AND CABINET OPENING DIMENSIONS:

21

5

/8"

(55.0 cm)

34

1

/2"

34

1

/2

"

34

1

/

2"

7

32

1

/2"

(82.5 cm) min.

(87.

5 cm) max

21

9

/16"

(54.7 cm)

Side View 24" Custom Wood Panel

32

1

/2"

(82.5 cm) min.

(87.

5 cm) max

23

1

/2"

(59.6 cm)

Front View

NOTE: Route the water supply line and power cable through

the channels provided under the dishwasher (circled above).

32

1

/2"

(82.5 cm) min.

(87.5 cm) max

22

7

/16

"

(57.0 cm)

22

5

/16"

(56.6 cm)

Side View 24" Metal Door Panel

24"

(61 cm) min.

24"

(61 cm)

min.

32

1

/2"

(82.5 cm) min.

Cutout Dimensions

Underside of countertop to oor

The enclosure must be at least 24" (61 cm) wide, 24" (61 cm)

deep, and

32½" (82.5 cm)

high.

For the front door of the dishwasher to be ush with the

leading edge of the counter top, the counter top must be

at least 24" (61 cm) deep.

This dishwasher is designed to be enclosed on the top and

on both sides by a standard residential kitchen cabinet unit.

The installation enclosure must be clean and free of any

obstructions.

NOTE: ADA installation, 32½" (82.5 cm) beneath 34" (86.4 cm)

high countertops may be accomplished by adjusting the toekick

and leveling legs.

24" PRODUCT AND CABINET OPENING DIMENSIONS:

21

5

/8"

(55.0 cm)

34

1

/

2"

34

1

/

2"

34

1

/2"

8

LOCATION REQUIREMENTS

Do not run drain lines, water lines or electrical wiring where they

can interfere with or contact dishwasher motors or legs.

The dishwasher installation location must provide clearance

between motors and ooring. Motors should not touch the oor.

Do not install dishwasher over carpeted ooring.

Protect dishwasher and the water lines leading to dishwasher

against freezing. Damage from freezing is not covered by the

warranty.

Check dishwasher installation location. The location must provide:

■ Easy access to water, electricity, and drain.

■ Convenient access for loading and unloading dishes. Corner

locations require a 2" (5 cm) minimum clearance between

the side of the dishwasher door and the wall or cabinet.

Countertop

Dishwasher

25

5

/

8

"

(65.1 cm)

2" (5.1 cm) min.

clearance for

door opening

■ Full enclosure on both sides, back, and top.

■ Square opening for proper operation and appearance.

■ Cabinet front perpendicular to oor.

■ Level oor. (If oor at front of opening is not level with oor

at

rear of opening, shims may be needed to level dishwasher.)

NOTE: To prevent shifting during dishwasher operation, shims

must be securely attached to the oor.

If dishwasher will be left unused for a period of time or in a location

where it may be subject to freezing, have it winterized by authorized

service personnel.

Make sure pipes, wires, and drain hose are within the area shown

in the “Cutout dimensions” section.

Helpful Tip: If the oor in the dishwasher opening is uneven,

(example: tile ooring only partway into opening) you will need

to take special care in measuring dimensions and in leveling

dishwasher.

DRAIN REQUIREMENTS

■ Use the new drain hose supplied with your dishwasher. If this

is not long enough, use a new drain hose with a maximum

length of 9.8 ft (3 m) from the sink that meets all current AHAM/

IAPMO test standards, is resistant to heat and detergent.

■ Connect drain hose to waste tee or disposer inlet above the

drain trap in the house plumbing and 20" (50.8 cm) minimum

above the oor. It is recommended that the drain hose be

either looped up and securely fastened to the underside of the

counter, or be connected to an air gap.

■ Use an air gap if the drain hose is connected to house

plumbing lower than 18" (45.7 cm) above the oor.

Use of air gap

■ Use 1/2" (1.3 cm) minimum I.D. drain line ttings.

WATER SUPPLY REQUIREMENTS

■ This dishwasher has a water heating feature and also requires

a connection to a hot water supply line.

■ A hot water line with 20-120 psi (138-862 kPa) water pressure.

■ 120°F (49°C) water at dishwasher.

■ 3/8" (.95 cm) O.D. copper tubing with compression tting or

exible stainless steel braided ll line (1/2" minimum plastic

tubing is not recommended).

■ A 90° elbow with 3/8" (.95 cm) N.P.T. external pipe threads

on one end.

NOTE: Do not solder within 6" (15.2 cm) from ll valve.

ELECTRICAL REQUIREMENTS

Contact a qualied electrician.

Assure that the electrical installation is adequate and in

conformance with all national and local codes and ordinances.

You must have:

■ 120 volt, 60 Hz, AC only, 15 or 20 amp., fused electrical supply.

■ Wiring must be 2 wire with ground.

We recommend:

■ A time-delay fuse or circuit breaker.

■ A separate circuit.

If direct wiring dishwasher:

■ Use exible, armored or non-metallic sheathed, copper wire

with grounding wire that meets the wiring requirements for your

home and local codes and ordinances.

If connecting dishwasher with a power supply cord:

■ Use Power Supply Cord Kit (Part No. 4317824) marked for use

with dishwashers. Kit contents include:

• UL listed 16 gauge 3 wire power supply

cord with 3 prong grounded plug.

• Neer C-500 7/8" (2.2 cm) strain relief.

• 3 wire connectors.

• Part No. 302797 grommet.

Follow the kit instructions for installing the power supply cord.

■ Power supply cord must plug into a mating three prong,

grounded outlet, located in the cabinet next to the dishwasher

opening. Outlet must meet all local codes and ordinances.

Air Gap

9

INSTALLATION INSTRUCTIONS

WARNING

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Electrical Shock Hazard

1. Disconnect power

2. Shut off water supply

Shut off the water supply to the dishwasher.

PREPARE CABINET OPENING—

NEW UTILITIES

3. Drill hole locations—new construction

NOTE: Refer to the “Product and Cabinet Opening Dimensions”

section for the correct hole placement and dimensions of the

shaded area.

Drill a 1½" (38 mm) drain hose hole in the side or rear of cabinet,

depending on location of drain hose routing and drain hose

connection location.

Drill a 1/2" (12.7 mm) water supply hose hole in the side or rear

of cabinet, depending on location of water supply routing and

connection location

Drill a 1½" (38 mm) electrical conduit hole in the right-hand side

or rear of cabinet.

4. Sand holes smooth

Wood

Cabinet

Metal

Cabinet

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover edges of hole with grommet included with

power cord kit. See the “Tools and Parts” section part details.

Helpful Tip: Wiring the dishwasher will be easier if you route

the cable into the cabinet opening from the right-hand side.

MOISTURE BARRIER - RECOMMENDED FOR

WOOD COUNTERTOPS

5. Moisture barrier/wood shims

Moisture

barrier

Make sure the area under the cabinet is clean and dry for

installation of the moisture barrier. Remove the backing of the

moisture barrier, and apply to underside of the countertop along

the front edge of the counter.

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

11/2"

(38 mm)

1/2"

(12.7 mm)

Optional

location

Preferred

location

10

DIRECT WIRE ROUTING

4"

6. Direct Wire—route cable

Direct wire

location

If direct wire, route the cable 4" (10.2 cm) from the right side of

the cabinet to align with channel in the bottom of the dishwasher.

Tape cable to the oor in the area shown. This will help secure

the cable in place when the dishwasher is moved into the cabinet

opening during direct wire connection.

PREPARE DISHWASHER

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

7. Put the dishwasher on its back

Dishwasher bottom

Helpful Tip: Place cardboard under dishwasher until installed

in cabinet opening to avoid damaging oor covering.

Using two or more people, grasp sides of dishwasher door frame,

and place the dishwasher on its back.

Do not use the door panel as a worktable without rst covering

it with a towel to avoid scratching the door panel.

11

REMOVE ACCESS PANEL

8. Remove access panel

Using a 1/4" nut driver or Phillips screwdriver, remove the two

screws attaching access panel to dishwasher.

9. Measure cabinet opening

Measure the height of cabinet opening from the underside of

the countertop to the oor where dishwasher will be installed.

Be sure to measure the lowest point on the underside of the

countertop and the highest point on the oor.

10. Leveling leg adjustment

Extend leveling legs out from the dishwasher base, 1/4" less than

the shortest opening height measured in cabinet opening.

Turn leg counter clockwise to raise the dishwasher or clockwise

to lower the diswasher.

CONNECT ELBOW TO VALVE

11. Connect elbow to ll valve

Elbow

Tighten elbow until snug, and be sure that it faces toward

channel in bottom of base.

12. Fill valve location

Fill valve location

CONNECT FILL HOSE TO ELBOW

13. Flexible line

Flexible braided line: Conrm the exible braided line is long

enough.

Attach exible line to elbow then route hose out the bottom left

channel under the dishwasher. Secure in channel with tape or

wire ties.

12

POWER CORD CONNECTION

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

NOTE: If removing a previous dishwasher with a power cord,

you will need to transfer the power cord to the new dishwasher.

14. Remove terminal box cover

Remove the screw holding the terminal box cover. Remove the

cover by sliding it up and lifting the hooks out of the slot. Keep

the cover for later use.

15. Install strain relief

Install a UL Listed/CSA Approved metallic strain relief. Make

sure screw heads are facing up when tightening conduit nut.

Strain relief is provided with the power cord kit. See the “Tools

and Parts” section for part details and ordering information.

16. Power cord—route cord into

terminal box

White

Black

Select UL Listed/CSA Approved twist-on wire connectors of the

proper size. See the “Tools and Parts” section for part details.

Connect wires, black-to-black and white-to-white, using the

twist-on wire connectors.

NOTE: Do not pre-twist stranded wire. Twist on wire connector.

Gently tug on wires to be sure both are secured.

Route cord so that it does not touch dishwasher motor or lower part

of dishwasher tub. Pull cord through strain relief in terminal box.

NOTE: A maximum of two power cord supply conductors

(12 AWG largest size) plus one grounding conductor are

permitted in the terminal box.

Remove the ground connector screw on the raised oor inside

the box and place it through the ring terminal of the green ground

wire of power cord. Reattach and tighten the ground connector

screw to the raised oor of the box. Tighten strain relief screws

to secure cord.

Wiring conguration

17. Power cord—reinstall terminal box

cover and wires

Place wires inside terminal box. Replace the cover by inserting

the hooks of the terminal cover into the slots in the oor of the

terminal box and sliding the cover tight against the back wall

where wires come in. Make sure wires are tucked inside the box

and not pinched by the cover.

NOTE: Route power cord out the bottom rear channel provided.

Do not plug cord into an outlet until instructed to do so.

Terminal

box cover

Terminal

box cover

13

UTILITY ROUTING CHANNEL LOCATON

18. Water supply hose, power cord

channel routing locations

Route water supply hose

and electrical supply through

the channels in the bottom

of base as shown.

Fill valve

Junction box

Electical cord

Hose

Channels

Route the water supply and electrical supply to the back of the

unit through the bottom base channels provided. Secure utilites

in channel using tape or wire ties.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

19. Stand dishwasher upright

Using two or more people, stand the dishwasher up.

NOTE: Do not install kick plate until instructed to do so.

Dishwasher may t tightly into cabinet opening. Do not remove

insulation blanket—the blanket reduces the sound level.

NOTE: Route water supply, drain hose, and power cord out the

rear of the dishwasher.

20. Move dishwasher close

to cabinet opening

Route the utilities through the holes in the cabinet, and pull

the slack out at the same time as the dishwasher is pushed into

the cabinet

21. Route power cord

If using a power cord, make sure to route the end through hole

in cutout before sliding dishwasher into the cabinet opening.

22. Secure insulation blanket

NOTE: Make sure insulation blanket is secured at both left and

right rear corners before pushing into cabinet opening to keep

the blanket from bunching up in a tight tting cabinet.

Water

line

Drain

Cable

Insulation

blanket

Secure

blanket

14

6"

(152 mm)

23. Move dishwasher all but 6" (152 mm)

into cabinet opening

NOTE: Leave unit about 6" (152 mm) out from cabinet in order

to install anchor brackets and adjust door tension if needed.

24. Pull slack from utilities

NOTE: Pull slack out of utilities at the same time the dishwasher

is pushed into the cabinet opening to avoid any kinks.

CHOOSE ANCHOR ATTACHMENT METHOD

OPTION #1 INSTALL ANCHOR BRACKETS FOR

UNDERCOUNTER ATTACHMENT

25. Top anchor brackets

The dishwasher must be secured to the countertop by the two

brackets located on top of the dishwasher

26. Install bracket into slots

Install both top brackets into slots on tub collar.

27. Attach bracket screws

Secure bracket to tub collar with provided screw.

OPTION #2 INSTALL SIDE MOUNTING BRACKETS

IF SIDEMOUNTING

28. Side mount bracket location

15

29. Break tab off

Break tab off at score line for side mounting.

30. Insert bracket into slot

Insert brackets into slot on either side of tub collar.

31. Secure sidemount with screw

Secure brackets into slot with proviced screws.

32. Slide completely into cut out

With top or side mount anchers attached, slide unit into cut

out until ush with cabinets.

33. Level front to back side to side

Using a level, adjust legs If needed.

Use a level to check if the dishwasher is level front to back. If the

dishwasher is not level front to back, adjust the height of the rear

leg until the dishwasher is level. Open the door of the dishwasher

and check that both the tub and door clearances are correct. If

not, rotate the leveling legs on the bottom front of the dishwasher.

You can also check this by placing a level against an inside front

vertical surface of the tub.

34. Leveling Leg adjustment

Turn leg counter clockwise to raise the dishwasher or clockwise

to lower the diswasher.

16

35. Open and close door

Open and close the door to check spring tension of door.

36. Adjust door spring tension

If needed adjust spring tension by using a Phillips-head screw

driver. Turn screws clockwise to increase tension or counter

clockwise to decrease door tension.

Screw to side

cabinet

37. Secure dishwasher

Open dishwasher door to prepare for securing the dishwasher

to the countertop or side cabinet.

NOTES:

■ The dishwasher must be secured to keep it from shifting when

the door is opened or closed.

■ Do not drop screws into bottom of dishwasher.

■ Locate brackets installed in the “Choose Anchor Attachment

Method” section, either on top or on the sides of the dishwasher.

■ If countertop anchoring: Secure dishwasher to the countertop

with two Phillips-head screws (included).

■ If side anchoring: Drill pilot holes in cabinet to avoid splitting

the wood. Secure dishwasher to cabinet with two Philips-head

screws (included). Remove upper rack for easier access. See

the User Guide for instructions on how to remove the upper

rack if needed.

Adjustment cap

Screw to side wall

38. Sidemount attachement method

Remove plastic caps covering screw holes on either side.

–

39. Drill pilot holes

If side anchoring: Drill pilot holes in cabinet to avoid splitting wood.

40. Install screws

Secure dishwasher to cabinet with two Phillips-head screws

(included). Remove upper rack for easier access. See the

User Guide for instructions how to remove the upper rack

if needed.

Adjustment cap

Screw to side wall

Door spring

adjustment screws

17

41. Reinstall plastic caps

Reinstall plastic caps to cover screw heads.

DIRECT WIRE ELECTRICAL CONNECTION

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Terminal

box cover

42. Remove terminal box cover

Remove the screw holding the terminal box cover. Remove the

cover by sliding it up and lifting its hooks out of the slot. Retain

cover for later use.

43. Install strain relief

Install a UL Listed/CSA Approved metallic strain relief. Make sure

screw heads are facing up when tightening conduit nut. Strain

relief is provided with the power cord kit. See the “Tools and Parts”

section for part details and ordering information.

black

white

ground

44. Direct Wire—Route cable into

terminal box

Select UL Listed/CSA Approved twist-on wire connectors of

the proper size. See the “Tools and Parts” section at the front

of the guide for part details. Connect wires, black-to-black and

white-to-white, using the twist-on wire connectors.

NOTE: Do not pre-twist stranded wire. Twist on the wire

connector. Gently tug on wires to be sure both are secured.

Route cable so that it does not touch dishwasher motor or lower

part of dishwasher tub. Pull cable through UL Listed/CSA Approved

strain relief in terminal box.

NOTE: A maximum of two field wiring supply conductors (12

AWG largest size) plus one grounding conductor are permitted in

the terminal box.

Form bare ground wire into a U-shaped hook. Wrap ground wire

hook clockwise around the ground connector screw on the

raised floor inside the box and under the washer. Securely

tighten ground connector.

Tighten strain relief screws to secure cable. Make sure screw

heads are facing up when tightening conduit nut.

Wiring conguration

18

Terminal

box cover

45. Power cord—reinstall terminal box

cover and wires

Place wires inside terminal box. Replace the cover by inserting

the hooks of the terminal cover into the slots in the oor of the

terminal box and sliding the cover tight against the back wall

where wires come in. Make sure wires are tucked inside the

box and not pinched by the cover.

CONNECT WATER LINE TO HOUSE

SHUT-OFF VALVE

NOTE: If using a exible braided hose, replace inlet hose after

5 years to reduce the risk of hose failure. Record hose installation

or replacement dates on the hose for future reference.

46. Attach water supply line

Attach the water supply line (copper tubing or exible braided

line) to the hot water line using a connection conguration that is

in compliance with local codes and ordinances. The water supply

to the dishwasher should have a manual shut-off valve located

under the sink.

CONNECT DRAIN HOSE

47. Connect drain hose

Connect drain hose to waste tee or waste disposer using

one of the following options:

■ Option A: Waste disposer – no air gap

■ Option B: No waste disposer – no air gap

■ Option C: Waste disposer – with air gap

■ Option D: No waste disposer – with air gap

Helpful Tip: To reduce vibration of the hose, keep the hose away

from the oor.

Drain hose

IMPORTANT: The drain hose connection to the disposer or a

waste tee must be made before the drain trap and at least 20"

(508 mm) above the oor where the dishwasher will be installed.

The drain hoes needs to be secured min of 30" off the oor and

fastened to cabinet or underside of the counter top.

Option A: Waste disposer—no air gap

Disposer inlet

Large drain

hose clamp

Drain hose

Drain trap

Helpful Tip: Remove disposer knockout plug.

1

1. Using a hammer and screwdriver, knock

plug into disposer.

2

2. Use needle-nose pliers to remove plug.

3

3. Attach drain hose to disposer inlet with

large 1" to 1½" drain hose clamp

(not provided).

19

Option B: No Waste disposer—no air gap

Waste tee

Large drain

hose clamp

Drain hose

Drain trap

1

Rubber

end

1. Fit rubber end of drain hose

towastetee.

2

2. Attach rubber end of drain hose to

waste tee with a hose clamp. Use a 1"

to 1

1

/

2

" (25 to 38mm) screw-type clamp

(not provided).

Helpful Tip: Remove disposer knockout plug.

1. Using a hammer and screwdriver, knock

plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Connect rubber end of drain hose

toairgap.

Option C: Waste disposer – with air gap

Large drain

hose clamp

Drain hose

Screw-type clamps

Air gap

Rubber hose

connector

Drain trap

Disposer inlet

1

2

Rubber

end

3

4

4. Attach rubber end of drain hose to air

gap with a hose clamp. Use a1" to 1

1

/

2

"

(25 to 38 mm) screw-type clamp

(not provided).

5

5. Use a rubber hose (not provided) with

screw-type clamps to connect from air

gap to disposer inlet.

1. Connect rubber end of drain hose

toairgap.

2. Attach drain hose to air gap. Use a

1" to 1

1

/

2

" (25 to 38 mm) screw-type

clamp.

3. Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from waste tee to air gap.

Option D: No waste disposer –

withairgap

Large drain

hose clamp

Drain hose

Screw-type clamps

Air gap

Rubber hose

connector

Drain trap

Waste tee

1

Rubber

end

2

3

COMPLETE INSTALLATION

Check that the power supply wire or cord does not touch

dishwasher motor or the lower part of the dishwasher tub.

48. Power supply cord—Plug into

a grounded 3 prong outlet

Plug into a grounded 3 prong outlet.

49. Reconnect power

Reconnect electrical power at the fuse box or circuit

breaker box.

NOTE: With the access panel off, start the dishwasher and allow

it to complete the shortest wash cycle. After the rst 2 minutes,

unlatch door, wait 5 seconds, then open door. Check that there is

water in the bottom of the dishwasher tub. Check that dishwasher

is working properly.

REINSTALL ACCESS PANEL

50. Reinstall panel

Place the panel against dishwasher legs. Using a Phillips

screwdriver or 1/4" nut driver, reinstall the screws through

the holes in the access panel.

51. Secure with screws

Check that the lower edge of the access panel touches the oor.

Adjust if necessary.

Tighten access panel screws.

CHECK OPERATION

■ Read the dishwasher User Guide that came with your

dishwasher.

■ Check that all parts have been installed and no steps were

skipped. Check that you have used all tools.

If the dishwasher is not working properly, disconnect power

or unplug dishwasher and refer to the “If Dishwasher Does Not

Operate” section.

IF DISHWASHER DOES NOT OPERATE

First try the solutions suggested here to possibly avoid the cost

of a service call.

■ Has the circuit breaker tripped or the house fuse blown?

■ Is the door closed tightly and latched?

■ Has the cycle been set correctly to start the dishwasher?

■ Is the water turned on?

If none of these possible solutions work, please see the User

Guide for service contact information.

ADDITIONAL TIPS

Expect longer wash times. Your new dishwasher will average 2-5

hours per load but use nearly 40% less energy than older models.

Designed with a low wattage, low energy consumption motor,

your dishwasher washes longer to ensure exceptional cleaning.

Certain models are equipped with an optical water sensor, so

the rst cycle will run longer to calibrate to the optical sensor.

Selecting certain options could increase cycle time past 3.5 hours.

Rinse aid is necessary for good drying results. This dishwasher

is designed to be used with rinse aid for good drying performance

and controlling hard water deposit buildup. Energy efcient

dishwashers use less water and energy, so they depend on the

water sheeting action of rinse aid for good drying performance.

La page charge ...

Whirlpool WDF550SAHW Guide d'installation

Whirlpool WDF550SAHW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents