Hypertherm Powermax30 AIR Field Service Bulletin

Marque: Hypertherm

Modèle: Powermax30 AIR

Taper: Field Service Bulletin

Field Service Bulletin

Bulletin de service sur le terrain

805430 Revision 4 February 2015

Révision 4 Février 2015

Powermax30

, Powermax30 XP, and

Powermax30 AIR Power Cord

Replacement

Remplacement du cordon

d’alimentation des Powermax30,

Powermax30 XP et Powermax30 AIR

Hypertherm Inc.

Etna Road, P.O. Box 5010

Hanover, NH 03755 USA

603-643-3441 Tel (Main Office)

603-643-5352 Fax (All Departments)

[email protected] (Main Office Email)

800-643-9878 Tel (Technical Service)

[email protected] (Technical Service Email)

800-737-2978 Tel (Customer Service)

customer.service@hypertherm.com (Customer Service Email)

866-643-7711 Tel (Return Materials Authorization)

877-371-2876 Fax (Return Materials Authorization)

[email protected] (RMA email)

Hypertherm Plasmatechnik GmbH

Technologiepark Hanau

Rodenbacher Chaussee 6

D-63457 Hanau-Wolfgang, Deutschland

49 6181 58 2100 Tel

49 6181 58 2134 Fax

49 6181 58 2123 (Technical Service)

Hypertherm (S) Pte Ltd.

82 Genting Lane

Media Centre

Annexe Block #A01-01

Singapore 349567, Republic of Singapore

65 6841 2489 Tel

65 6841 2490 Fax

65 6841 2489 (Technical Service)

Hypertherm (Shanghai) Trading Co., Ltd.

Unit 301, South Building

495 ShangZhong Road

Shanghai, 200231

PR China

86-21-60740003 Tel

86-21-60740393 Fax

Hypertherm Europe B.V.

Vaartveld 9

4704 SE

Roosendaal, Nederland

31 165 596907 Tel

31 165 596901 Fax

31 165 596908 Tel (Marketing)

31 165 596900 Tel (Technical Service)

00 800 4973 7843 Tel (Technical Service)

Hypertherm Japan Ltd.

Level 9, Edobori Center Building

2-1-1 Edobori, Nishi-ku

Osaka 550-0002 Japan

81 6 6225 1183 Tel

81 6 6225 1184 Fax

Hypertherm Brasil Ltda.

Rua Bras Cubas, 231 – Jardim Maia

Guarulhos, SP - Brasil

CEP 07115-030

55 11 2409 2636 Tel

55 11 2408 0462 Fax

Hypertherm México, S.A. de C.V.

Avenida Toluca No. 444, Anexo 1,

Colonia Olivar de los Padres

Delegación Álvaro Obregón

México, D.F. C.P. 01780

52 55 5681 8109 Tel

52 55 5683 2127 Fax

Hypertherm Korea Branch

#3904 Centum Leaders Mark B/D,

1514 Woo-dong, Haeundae-gu, Busan

Korea, 612-889

82 51 747 0358 Tel

82 51 701 0358 Fax

Powermax and Hypertherm are trademarks of Hypertherm Inc. and may be registered in the United States and/or other countries. All other trademarks

are the property of their respective holders.

Powermax et Hypertherm sont des marques d’Hypertherm Inc. qui peuvent être déposées aux États-Unis et/ou dans d’autres pays. Toutes les autres

marques commerciales sont la propriété de leurs détenteurs respectifs.

Powermax30/30 XP/30 AIR Field Service Bulletin 805430 3

Power Cord Replacement

Introduction

Purpose

Describes the necessary steps to replace the power cord and strain relief on CSA and CE Powermax30 power supplies.

Powermax30 XP and Powermax30 Air systems: Complete instructions for installing these repair kits, as well as the

CCC power cord repair kit (428231) for the Powermax30 XP and the CE power cord repair kit (428390) for the

Powermax30 Air, are included in the Service Manual. To download the Service Manual, go to www.hypertherm.com

and

click the “Downloads library” link.

 Powermax30 XP Service Manual (808150)

 Powermax30 Air Service Manual (808850)

Tools and materials needed

 Assorted Phillips

and TORX

screwdrivers

 Needle nose pliers

 Adjustable wrench

WARNING!

ELECTRIC SHOCK CAN KILL

Disconnect electrical power before performing any maintenance.

See the Safety and Compliance Manual (80669C) for more safety

precautions.

4 Powermax30/30 XP/30 AIR Field Service Bulletin 805430

Power Cord Replacement

Kit 228210 contents (CSA)



The 120 V/15 A CSA plug adapter (229132) and the 240 V/20 A CSA plug adapter

(229133) must be ordered separately from the power cord kit.

Kit 228140 contents (CE)

Kit 228143 contents

Replace the power cord

Remove the rear panel

1. Set the power switch to OFF (O), disconnect the power cord from the power source, and disconnect the gas supply.

2. Remove the 2 screws from the handle on the top of the power supply.

3. Slightly tip the front and rear panels away from the power supply so that you can get the edges of the handle out from

underneath them. Remove the handle, and set it and the 2 screws aside.

Figure 1

Part number Description Quantity

229135 Power cord assembly: Powermax30, Powermax30 XP, and

Powermax30 Air L6-20P

Part number Description Quantity

229120 Power cord assembly: Powermax30 and Powermax30 XP CE 1

Part number Description Quantity

008389 Strain relief: 0.428 – 0.546 black vinyl 1

Powermax30/30 XP/30 AIR Field Service Bulletin 805430 5

Power Cord Replacement

4. Continue to tilt the panels outward to release the fan side of the cover from its track. Then lift the cover off the power

supply.

5. Remove the component barrier from the power board side of the power supply. The barrier is flexible and can be bent

slightly for removal.

Figure 2

6. Loosen the power cord’s strain relief nut.

7. Lay the power supply on its side.

8. Remove the retaining screw from the bottom of the rear panel.

Figure 3

Component barrier

2 3 4

Rear panel

Snap

Retaining screw

Raised rib

6 Powermax30/30 XP/30 AIR Field Service Bulletin 805430

Power Cord Replacement

9. Insert needle nose pliers into the opening for one of the snaps and use the pliers to squeeze it together.

10. Place a blade screwdriver against the raised rib next to the snap and gently turn the screwdriver to push the panel

away from the base.

Figure 4

11 . Place another screwdriver or similar object into the opening between the panel and the base to keep the first corner

of the panel from re-engaging the snaps when you release the other corner.

Figure 5

12. Repeat step 9 and step 10 on the other corner of the panel.

Powermax30/30 XP/30 AIR Field Service Bulletin 805430 7

Power Cord Replacement

13. Disconnect the ground wire from the ground wire clip near the top of the rear panel. (See Figure 6.)

Figure 6

14. Gently pull the panel away from the power supply.

Ground wire clip

Rear panel

8 Powermax30/30 XP/30 AIR Field Service Bulletin 805430

Power Cord Replacement

Remove the power cord (CSA)

The power cord has a black wire and a white wire that connect to the power switch and a green ground wire that

connects to the heatsink.

1. Remove the black and white wires from the top of the power switch. You can use needle nose pliers or a straight

screwdriver to ease them off, if necessary.

Figure 7

2. Remove the screw that holds the ground wire to the heatsink. A notch in the power board provides access to the

screw. (See Figure 8.)

Figure 8

Powermax30/30 XP/30 AIR Field Service Bulletin 805430 9

Power Cord Replacement

3. On the outside of the power supply, loosen the power

cord’s strain relief nut (see Figure 9) so that the wires

move freely.

4. From outside of the power supply, pull the wires

through the strain relief and through the hole in the rear

panel to remove the power cord.

5. Are you replacing the strain relief?

 If yes, use an adjustable wrench to unscrew the

retention nut on the inside of the power supply.

Remove the strain relief from the rear panel.

 If no, continue with Install the new power cord

(CSA).

Figure 9

Outside

Inside

Strain relief nut (outside the power supply)

Strain relief

Rear panel

Retention nut (inside the power supply)

10 Powermax30/30 XP/30 AIR Field Service Bulletin 805430

Power Cord Replacement

Install the new power cord (CSA)

1. Are you installing a new strain relief?

 If yes, insert the strain relief into the rear panel and tighten the retention nut onto the strain relief. Loosely tighten

the strain relief nut on the outside of the power supply onto the strain relief.

 If no, continue with the next step.

2. Route the power cord wires through the strain relief nut and strain relief.

3. Press the connector for the black wire onto the pin on the upper left side of the power switch. Press the connector

for the white wire onto the pin on the upper right side of the power switch.

4. Tighten the green ground wire to the heatsink with a torque setting of 17.28 kg-cm (15 inch-pounds).

5. Press the wires into the track going up the side of the rear panel.

Powermax30/30 XP/30 AIR Field Service Bulletin 805430 11

Power Cord Replacement

Remove the power cord (CE)

1. Remove the blue and brown wires from the power switch. You can use needle nose pliers or a straight screwdriver to

ease it off, if necessary.

2. Remove the screw that holds the green/yellow ground wire to the heatsink. A notch in the power board provides

access to the screw.

Figure 10

3. On the outside of the power supply, loosen the

power cord’s strain relief nut so that the wires move

freely.

4. Remove the power plug from the old power cord.

5. From the inside of the power supply, pull the wires

through the strain relief and the hole in the rear

panel. (You cannot remove the wires from outside

the power supply because of the ferrite bead

installed on the wires.)

6. Are you replacing the strain relief?

 If yes, use an adjustable wrench to unscrew the

retention nut on the inside of the power supply.

Remove the strain relief from the rear panel.

 If no, continue with Install the new power cord

(CE).

12 Powermax30/30 XP/30 AIR Field Service Bulletin 805430

Power Cord Replacement

Figure 11

Install the new power cord (CE)

1. Are you installing a new strain relief?

 If yes, insert the strain relief into the rear panel and tighten the retention nut onto the strain relief. Loosely tighten

the strain relief nut on the outside of the power supply onto the strain relief.

 If no, continue with the next step.

2. Route the wires for the power cord through the strain relief from the inside of the rear panel.



Because the power cord includes the ferrite bead, you cannot route the power cord

through the strain relief from the outside of the power supply. Do not remove the ferrite

bead from the power cord wires.

3. Press the connector for the brown wire onto the pin on the upper left side of the power switch.

4. Press the connector for the blue wire onto the pin on the upper right side of the power switch.

5. Tighten the green/yellow ground wire to the heatsink with a torque setting of 17.28 kg-cm (15 inch-pounds).

6. Press the wires into the track going up the side of the rear panel.

Outside

Inside

Strain relief nut (outside the power supply)

Strain relief

Rear panel

Retention nut (inside the power supply)

Powermax30/30 XP/30 AIR Field Service Bulletin 805430 13

Power Cord Replacement

Reinstall the rear panel

1. Push the rear panel into the base to re-engage the snaps.

2. Verify the hole in the ground wire clip is aligned with the screw holes in the rear panel and the power supply.

3. Tighten the retaining screw with a torque setting of 8.1 kg-cm (7 inch-pounds).

4. Reconnect the ground wire to the ground wire clip.

5. Tighten the strain relief nut on the power cord.

6. Hold the component barrier so that the edge with the long cutout and the two notches is closest to the rear panel,

and the edge with the three notches is closest to the front panel.

7. A perforated line runs across the top of the barrier, about 25 mm (1 inch) below the top edge. Fold the barrier along

this perforation so that the top edge bends away from you.

8. Position the barrier so that the folded section will cover the top of the power board. The edge with the long cutout

and the two notches should align with the front panel; the edge with the three notches should align with the rear

panel.

9. Put the front-panel edge of the barrier in place first, then the rear-panel edge. The notches on each side of the barrier

should align with the ribs on the inside of the front and rear panels. As you slide the barrier into place, make sure the

bottom edge is in the same track the cover rests in.

10. Being careful not to pinch any wires, slide the cover onto the power supply. Align the bottom edges with the tracks,

and align the slot in the top of the cover with the tab on the front panel so that the louvers in the cover are in front of

the fan.

Figure 12

Cover slot

Front panel

Tab

14 Powermax30/30 XP/30 AIR Field Service Bulletin 805430

Power Cord Replacement

11 . Realign the front panel with the power supply.

12. Realign the rear panel with the power supply, making sure that the hole in the ground clip is aligned with the screw

holes in both the panel and the power supply.

13. Position the handle over the holes in the top of the cover, and position the ends of the handle underneath the edges

of the panels.

14. Reinstall the 2 screws that attach the cover and handle with a torque setting of 23.0 kg-cm (20 inch-pounds).

15. Reconnect the gas supply and power cord, and set the power switch to ON (I).

Powermax30/30 XP/30 AIR Bulletin de service sur le terrain 805430 15

Remplacement du cordon d’alimentation

Introduction

Objet

Décrit les étapes nécessaires au remplacement du cordon d’alimentation et du serre-câble des sources de courant des

Powermax30 CSA et CE.

Systèmes Powermax30 XP et Powermax30 AIR : Les instructions complètes pour l’installation de ces kits de

réparation ainsi que du kit de réparation du cordon d’alimentation CCC (428231) pour le Powermax30 XP et du kit de

réparation du cordon d’alimentation CE (428390) pour le Powermax30 AIR, sont incluses dans le Manuel de service.

Pour télécharger le Manuel de service, se rendre sur www.hypertherm.com

et cliquer sur le lien « Bibliothèque de

téléchargement ».

 Manuel de service Powermax30 XP (808150)

 Manuel de service Powermax30 AIR (808850)

Outils et matériel requis

 Tournevis Phillips

et TORX

assortis.

 Pinces à bec fin

 Clé ajustable

AVERTISSEMENT !

UN CHOC ÉLECTRIQUE PEUT ÊTRE MORTEL

Avant tout entretien, débrancher l’alimentation électrique.

Se reporter au Manuel de sécurité et de conformité (80669C) pour

des mesures de sécurité supplémentaires.

16 Powermax30/30 XP/30 AIR Bulletin de service sur le terrain 805430

Remplacement du cordon d’alimentation

Contenu du kit 228210 (CSA)



Les adaptateurs de fiche 120 V/15 A CSA (229132) et 240 V/20 A CSA (229133)

doivent être commandés séparément du kit de cordon d’alimentation.

Contenu du kit 228140 (CE)

Contenu du kit 228143

Remplacement du cordon d’alimentation

Retirer le panneau d’extrémité arrière.

1. Couper l’alimentation (OFF) (O), débrancher le cordon d’alimentation de la source de courant et débrancher

l’alimentation en gaz.

2. Déposer les deux vis de la poignée en haut de la source de courant.

3. Basculer légèrement les panneaux d’extrémité avant et arrière de la source de courant de façon à en extraire les

bords de la poignée d’en dessous. Enlever la poignée et la mettre de côté avec les deux vis.

Figure 13

Numéro de référence Description Quantité

229135 Ensemble du cordon d’alimentation : Powermax30,

Powermax30 XP et Powermax30 AIR L6-20P

Numéro de référence Description Quantité

229120 Ensemble du cordon d’alimentation : Powermax30 et

Powermax30 XP CE

Numéro de référence Description Quantité

008389 Serre-câble : 0,428 – 0,546 vinyle noir 1

Powermax30/30 XP/30 AIR Bulletin de service sur le terrain 805430 17

Remplacement du cordon d’alimentation

4. Continuer à incliner les panneaux vers l’extérieur pour dégager le couvercle côté ventilateur de ses rails. Retirer

ensuite le couvercle de la source de courant.

5. Retirer la barrière de composant du côté du panneau d’alimentation de la source de courant. Cette barrière est

flexible et peut être pliée légèrement pour être enlevée.

Figure 14

6. Desserrer l’écrou du serre-câble du cordon d’alimentation.

7. Coucher la source de courant sur le côté.

8. Retirer les vis de retenue de la partie inférieure des panneaux avant et arrière.

Figure 15

Barrière de composant

2 3 4

Panneau arrière

Fermoir

Vis de fixation

Nervure en saillie

18 Powermax30/30 XP/30 AIR Bulletin de service sur le terrain 805430

Remplacement du cordon d’alimentation

9. Insérer les pinces à bec fin dans l’orifice d’un des fermoirs et serrer ses deux côtés ensemble à l’aide des pinces.

10. Appuyer un tournevis plat contre la nervure en saillie située à côté du fermoir et tourner doucement le tournevis de

sorte à éloigner le panneau du socle.

Figure 16

11 . Placer un autre tournevis ou autre objet semblable à l’intérieur de l’orifice entre le panneau et le socle, afin

d’empêcher le premier coin du panneau de s’enclencher à nouveau dans le fermoir lorsque l’autre coin est dégagé.

Figure 17

12. Répéter étape 9 et étape 10 à l’autre angle du panneau.

Powermax30/30 XP/30 AIR Bulletin de service sur le terrain 805430 19

Remplacement du cordon d’alimentation

13. Déconnecter le fil de mise à la terre du collier de mise à la terre situé près du dessus du panneau arrière.

(Consulter Figure 18.)

Figure 18

14. Tirer délicatement le panneau loin de la source de courant.

Collier de mise à la terre

Panneau arrière

20 Powermax30/30 XP/30 AIR Bulletin de service sur le terrain 805430

Remplacement du cordon d’alimentation

Retrait du cordon d’alimentation (CSA)

Le cordon d’alimentation possède un fil noir et un fil blanc qui se branchent sur l’interrupteur, ainsi qu’un fil de terre vert

qui se raccorde au dissipateur thermique.

1. Retirer les fils noir et blanc au-dessus de l’interrupteur d’alimentation. Si nécessaire, il est possible d’utiliser une

pince à bec fin ou un tournevis droit pour faciliter leur retrait.

Figure 19

2. Déposer la vis utilisée pour fixer le fil de terre sur le dissipateur thermique. Une encoche dans le circuit imprimé

permet l’accès à la vis. (Consulter Figure 20.)

Figure 20

La page est en cours de chargement...

Hypertherm Powermax30 AIR Field Service Bulletin

Marque: Hypertherm

Modèle: Powermax30 AIR

Taper: Field Service Bulletin

Télécharger le PDF

rapport

dans d''autres langues

English: Hypertherm Powermax30 AIR

Hypertherm Powermax30 AIR Field Service Bulletin

Hypertherm Powermax30 AIR Field Service Bulletin

dans d''autres langues

Documents connexes

Autres documents