MOUSER ELECTRONICS RM-2450 Manuel utilisateur

Marque: MOUSER ELECTRONICS

Modèle: RM-2450

Catégorie: Des ponts

Taper: Manuel utilisateur

Doodle Labs Smart Radio – RM-2450

Advanced MIMO Mesh Router

Smart Radio Overview

The Smart Radio is an advanced 2×2 MIMO mesh router designed for easy plug & play

integration. The tiny module carries all bi-directional communication (e.g. Telemetry, Video) in a

single high-speed broadband RF channel.

Due to its very low SWaP-C (Space, Weight and Power and Cost), the Smart Radio is very popular

for mobile IIoT (Industrial Internet of Things) applications like drones, autonomous vehicles, and

mobile robotics applications across various industries.

Embedded

Technical Specifications (RM-2450)

Model Category Xtreme

ORDERING CODES

Radio Configuration 2x2 MIMO

Model #

(v3 hardware)

RM-2450-2J-XM (Embedded, Industrial temp)

RM-2450-2J-XM-C (Embedded, Commercial temp)

Evaluation Kit EK-2450-2J (Ethernet board for Embedded model)

Design-In Documentation https://www.doodlelabs.com/technologies/technical-library/

PERFORMANCE OVERVIEW

Protocol Compatibility Fully compatible with 2.4GHz (IEEE 802.11g,n)

Max Operating Range

(Indicative)

>20 Km (Recommended), (Max field demonstrated range >100km)

Max Data Throughput at

10-meter range

(Indicative)

100 Mbps (40 MHz Channel)

80 Mbps (20 MHz Channel)

Over the Air Data

Encryption

256-bit AES software encryption

(12 Mbps max throughput)

(FIPS140-2, Level 2 compliant)

Operating Modes Mesh, Relay, Routed Client, AP, Transparent Bridge, Internet Gateway

Command & Control

Channel Ultra-Reliable Low Latency Channel (URLLC). Latency 3-30 ms

Video Channel Optimized video streaming with Unicast and Multicast transmission

Spectrum Scan Automatic spectrum scan on boot up.

Mesh Automatic Transmit

Power Control

Intelligently adjusts Tx output power based on signal strength. Allows

the device to be utilized in a dispersed and dynamic mesh.

Model Category Xtreme

RF SPECIFICATIONS

Frequency Range 2400-2482 MHz

Model Category Xtreme

Channel Sizes

(Software Selectable) 20, 40 MHz

Radio Data Rate

(Modulation Coding

Scheme

–

MCS)

Dynamic Link Auto Adaptation

Antenna Signal Strength -25 to -85 dBm (Recommended), Absolute Maximum= +12 dBm

Receiver LNA Gain >10 dB

RF Power Control In 1dB steps, Tolerance +/-1dB

Integrated Antenna Port

Protection

Able to withstand open port, >10 KV (contact) and >15KV (open air

discharge) as per IEC-61000-4-2

Wireless Error Correction FEC, ARQ

Frequency Accuracy ±10 ppm max over life

Control for External

Power Amp DC biased signal over RF port

Automatic Transmit

Power Control (ATPC)

Automatic adjustment of Tx power based on signal level, which ensures

optimal link health at both short and long distances

NETWORKING SPECIFICATIONS

Mesh Router Self-Forming/Self-Healing, Peer to Peer

Video Multicast High Rate

Custom Software

Package Manager OPKG

Device Management SSH, RPC-JSON, LuCI, GUI

Access control Password, MAC, IP, Port filtering

Network Security VPN, L2TP, GRE, STP

Supported Protocols IPv6, QoS, DNS, HTTPS, IP, ICMP, NTP, DHCP

Integrate with 3rd Party

Apps Integrate with various apps e.g. ATAK, QGroundControl, and more

Software Upgrade Over the air software upgrade supported

HARDWARE SPECIFICATIONS

Case Material Aluminum (Embedded)

Operating Voltage 6~42V DC

Model Category Xtreme

Dimensions 65 x 57 x 12 mm, 78 grams (Embedded)

Interfaces 2x RJ45, UART, USB, 2x GPIO

Antenna Connection 2x MMCX-Female (Embedded)

Host Interface

(Embedded)

2x Ethernet (100 Base-T) and UART (3.3V FT234XD chipset) OR USB

2.0 Hub

Temperature range

(Operating)

Industrial: -40°C to +85°C, Commercial: -10°C to +65°C

System’s thermal design should ensure that the radio’s case

temperature is maintained within these specifications.

Ingress Protection

(Embedded) IP 50 (Embedded), Dust Protected, No Liquids

Shock and Vibration

Resistance Compliant to MIL-STD-810H for high shock and vibration

DC Power Consumption  14W @ Max RF power in UDP data Tx mode

 2W in data Rx mode

 1.2W in Sleep mode

Reliability Extreme Reliability, IPC Class 2 standard with Class 3 options

Integrated GPS (Optional)

Simultaneous multiple constellations

(GPS/Galileo/Glonass/BeiDou/QZSS), 1.5 meter CEP position

accuracy, -163 dBm tracking sensitivity

Integrated CPU MIPS 24K, 540 MHz, 32MB Flash, 64MB DDR2 RAM

MTBF >235k hours (25 years)

Temper Evident Seal Yes

Humidity (Operating) 0% – 95% (Non-condensing)

Life Cycle Planning

Extended lifespan with 7 years guaranteed availability

REGULATORY INFORMATION

FCC ID 2AG87RM2450-2J (In Progress)

Industry Canada (IC) 21411-RM24502J (In Progress)

Model Category Xtreme

Regulatory Requirements

Designed and verified to meet various regulatory requirements. Formal

testing and approval are required for the Integrator’s antenna type. The

Integrator is responsible for obtaining all regulatory approvals in target

markets for the finished product.

RoHS/WEEE Compliance Yes. 100% Recyclable/Biodegradable packaging

* Specifications are subject to change without prior notice.

FCC Regulatory Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy, and if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

The antenna used with this transmitter must be installed to provide a minimum separation distance of at least

20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or

transmitter, except in accordance with FCC multi- transmitter product procedures.

Country Code selection feature to be disabled for products marketed to the US/Canada.

This device is intended only for OEM integrators under the following conditions:

1. The antenna must be installed such that 20cm is maintained between the antenna and users, and

2. The transmitter module may not be co-located with any other transmitter or antenna,

Important Note:

In the event that these conditions cannot be met (for example certain laptop configurations or co-location

with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be

used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating

the end product (including the transmitter) and obtaining a separate FCC authorization.

Labeling and Notice to OEM Integrator

If the FCC ID is not visible when the module is installed inside another device, then the outside of the

finished product into which the module is installed must display a label referring to the enclosed module. This

exterior label can use wording as follows:

For the RM-2450-2J:

Contains Transmitter Module FCC ID: 2AG87RM2450-2J

Contains FCC ID: 2AG87RM2450-2J

A transmitter with a modular grant can be installed in different end-use products (referred to as a host, host

product, or host device) by the grantee or other equipment manufacturer, then the host product may not

require additional testing or equipment authorization for the transmitter function provided by that specific

module or limited module device.

A host product itself is required to comply with all other applicable FCC equipment authorization

regulations, requirements, and equipment functions that are not associated with the transmitter module

portion. For example, compliance must be demonstrated: to regulations for other transmitter components

within a host product; to requirements for unintentional radiators (Part 15 Subpart B), such as digital

devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for the

non-transmitter functions on the transmitter module (i.e., Verification or Declaration of Conformity) as

appropriate (e.g.,Bluetooth and Wi-Fi transmitter modules may also contain digital logic functions).

Reference to KDB Publication 996369 D04 Module Integration Guide (which is available at the FCC Office of

Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB)

https://apps.fcc.gov/oetcf/kdb/index.cfm ), any manufacturer of the host device which installs this modular

with unlimited modular approval should perform the test of radiated and conducted emission and spurious

emission, etc. according to FCC CFR Title 47 Part 15.247 requirement, only if the tests result comply with

FCC CFR Title 47 Part 15.247 requirement, then the host can be sold legally.

A user's manual for the finished product should include the following statement: