Honeywell RCHT9610WFSW2003/U Guide d'installation

T9 SMART THERMOSTAT

RCHT9510WFW2019

Installation Guide

Online Guides

Resideo.com

2

M38354

Read before installing.

Included in your box:

Thermostat

Literature

Screws and anchors

T9 Smart Thermostat

UWP Wallplate

Wire labels

3

Tools you will need: You may need:

Phillips screwdriver Wire Stripper

Home WiFi Password

Small ﬂat head screwdriver

Needle-nose pliers

Pencil

Drill and drill bit

Level

Flashlight

4

Compatibility Section

• REQUIRED: A CWire (common wire) is needed for 24 VAC power. If you do not have a CWire,

a FREE CWire Adapter offer is included.

This guide will help you determine if you have a CWire or will need to use a CWire Adapter (Step

10). The CWire is a wire that originates from your heating and cooling system and needs to be

connected to the C terminal on your thermostat. There is no universal color used to designate

this type of wire.

• Compatible with most heating/cooling, and heat pump systems

• Does not work with electric baseboard heat (120240V)

• Does not work with millivolt systems

• Does not support S terminals for indoor and outdoor sensors

• Android or iOS smartphone, tablet, or device

C

CU

GY

A

OR

CWire CWire Adapter

(FREE CWire

Adapter offer

included)

5

For help, see:

ONLINE GUIDES AND SUPPORT VIDEOS AT: Resideo.com

SOCIAL Twitter: @Honeywell_Home, Facebook: Honeywell Home

Or contact:

PHONE 18006333991

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before beginning installation.

CAUTION: EQUIPMENT DAMAGE HAZARD

Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the compressor quickly.

CAUTION: MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact

your local waste management authority for instructions regarding recycling and proper disposal.

6

Removing your old thermostat

You will need: Screwdriver, needle-nose pliers

OFF

ON

75

1

2

3

Turn off power

To protect your equipment, turn off the power

at the breaker box or switch that controls you

heating and cooling equipment.

Note: The thermostat off switch will not turn off

the power to the equipment.

Check that your system is off

Change the temperature on your old thermostat so

that your system starts heating or cooling.

If you don’t hear or feel the system turn on within 5

minutes, the power is off.

Note: If you have a digital thermostat that has a blank

display, skip this step.

Remove your existing thermostat from the wall

plate

On most thermostats, you can take off the thermostat

by grasping and gently pulling. Some thermostats

may have screws, buttons, or clasps.

Do not remove any wires from your thermostat at

this time!

OR

OFF

Breaker box

Switch

7

5

4

Take a picture of your existing wall plate’s wiring

In order to capture all of the letters next to the

terminals, be sure to take multiple pictures from

different angles.

You may need to reference this image later.

Do you have a line voltage system?

Line voltage systems have thick black wires with

wire nuts or are labeled high voltage (120V or

higher).

Your system is not compatible. Go to

Resideo.com to ﬁnd a pro installer in your

area.

Continue to the next step.

Wire nut

Thick black wire

Compatibility Check

YES

NO

8

6

7

Remove any jumpers

A jumper is used to connect two terminals. It may look

like a small staple or a colored wire.

Do not discard.

Keep jumpers with your old wallplate.

Label the wires

Use the stickers provided with your new thermostat to

label each wire on your existing wall plate.

Do not label jumpers. Your new thermostat does not

need jumpers.

Example

of a jumper

Terminals

YRRC

8Write down the colors of the wires

Check the boxes and write down the color of the wires connected to terminals that are coming

from the wall. Check all that apply (not all will apply).

Terminal Wire Color Terminal Wire Color

¨A or L/A ¨R

¨CRequired* ¨Rc

¨E¨Rh

¨G¨W

¨K¨W2 or Aux

¨O/B ¨Y

¨U (1 or 2)** ¨Y2

* A C-wire or CWire Power Adapter (see included free offer) is required.

** The T9 Smart thermostat cannot control equipment wired to U1 or U2.

If there are wires in terminals that are not listed, you will need additional wiring support. Visit

Resideo.com to ﬁnd out more.

9

10 Do you have a CWire?

Look at the thermostat wiring checklist from

Step 8, or the photo you took. Is the CTerminal

checked?

This means you will not need to install a

CWire Adapter. Skip to Installing Your New

Thermostat (page 13).

This means you don’t have a C-wire connected

to your thermostat. Continue to next step.

Compatibility Check

YES

NO

9Disconnect the wires and remove the old wall

plate

You may need a screwdriver to release wires from

terminals.

Tip: Wrap the wires around a pencil to prevent them

from falling in the wall.

C

CU

GY

A

10

11

12

Do you have a zoning panel?

You have a zoning panel if you have multiple

thermostats and one furnace or heating system.

CWire Adapter installation is more complicated

on zoned systems. Go to Resideo.com to ﬁnd a

pro installer in your area.

Proceed to the next step.

Do you have an unused wire?

Look at the bundle of wires coming from the wall.

Note: You may have to pull the bundle of wires out

from the wall to ﬁnd the unused wire.

Continue to Step 13.

See the CWire Power Adapter FREE OFFER

included in the thermostat box. Follow the

instructions that come with the CWire Power

Adapter, and then return to page 13 of this

guide to complete the installation.

Compatibility Check

YES

NO

Only complete this section if you answered No to Step 10

Connecting Your Unused CWire

You will need: Screwdriver, ﬂashlight, wire strippers

Thermostat

Furnace

Example of unused C-wire

Zoning

Panel

11

13 Label unused wire

Label your unused wire with the

provided “C” sticker label. You may need

to use a wire stripper to expose at least

1/4 inch of the wire.

Note: If you have multiple unused wires,

then label only one wire and make note

of the color here:

-

Go to your furnace or heating system

This system is often located in your basement, attic or garage.

Bring a ﬂashlight and screwdriver.

14 Remove cover from furnace or heating system

Open the heating and cooling system’s cover to ﬁnd

the control board. You should see the same terminal

labels that are on your thermostat.

Note: You may need to unscrew the cover. The

control board may be at the top or bottom.

G

C

R

W

Y

12

16

15

17

Connect the unused wire to the C-terminal

Note: If there are existing wires in the C-terminal,

make sure they are still connected to the C-terminal

after connecting this wire.

Find the other end of the unused wire

Locate the bundle of wires that are the same as the

ones at your thermostat.

The unused wire should be the same color as the one

near your existing thermostat. See Step 13 for the

color you wrote down.

Close the cover to the furnace or heating system

Be sure the cover is completely closed. Some systems

will not power up if the cover isn’t fully closed.

You’ve connected the C-wire.

You will NOT need to use a CWire Adapter.

G

C

R

W

Y

G

C

R

W

Y

-

Go back to the wall where you are installing your thermostat and continue to “Installing Your

New Thermostat” on the next page.

13

Installing Your New Thermostat

You will need: Level, pencil, drill and a drill bit

Thermostat Screws UWP

wallplate

WallAnchors

14

18

19

Position wall plate

Pull open the wall plate that was included with your

new thermostat. Insert the bundle of wires through

the back of the wall plate.

Make sure at least 1/4-inch of each wire is exposed

for easy insertion into the wire terminals.

Insert recommended wall anchors

It is recommended that you use the wall anchors included in the box to mount your thermostat.

You can use the wall plate to mark where you want to place the wall anchors.

a) Level the wall plate

b) Mark the location of the wall anchors using a pencil

c) Remove the wall plate

d) Drill anchor holes.

If your box contains red anchors, drill 7/32” holes.

If your box contains yellow anchors, drill 3/16” holes.

e) Insert the wall anchors

f) Make sure the anchors are ﬂush with the wall

g) Reposition the wall plate on wall

-

UWP

Anchors Wall

15

1. Ensure the

right R-switch

is in the up

position.

1. Set right

R-switch to the

down position.

UWP

20 Determine Correct RSwitch Position and Insert R-wire or wires

Set the R-switch up or down based on your wiring notes in Step 8. Insert wires into the inner

holes of the terminals on the wall plate. The tabs will stay down once the wire is inserted.

If you have 1 RWire (R, RC, RH):

If you have 2 RWires (R, RC, RH):

2. Insert your

R-wire (R, Rh

or Rc) into

R-terminal.

2. Insert your Rc

wire into Rc-

terminal.

3. Insert your R

or Rh wire into

R-terminal.

OR

16

22

23

Close the door and mount the wall plate

Mount the wall plate using the provided screws.

Install all three screws for a secure ﬁt on your wall.

Tip: Prior to tightening the screws, use a level to

ensure the wall plate is level.

Attach your thermostat

Align the thermostat on the wall plate and ﬁrmly snap

into place.

21 Connect remaining wires from Step 8

Push down on the tabs to put the wires into the inner

holes of their corresponding terminals on the wall

plate (one wire per terminal) until it is ﬁrmly in place.

Gently tug on the wires to verify they are secure.

Tip: If you need to release the wires again, push down

the terminal tabs on the sides of the wall plate.

This wiring is just an example,

actual wiring may vary.

17

24

25

Turn power back on

Turn on the switch that controls your heating and

cooling system.

Complete setup on the thermostat

Remove the protective ﬁlm and conﬁrm that your

thermostat reads “Welcome.”

If you do not see this, visit

Resideo.com or call 18006333991 for more help.

Go back to your circuit breaker box.

Go back to your thermostat.

OFF

ON

Breaker box

Switch

Welcome!

18

Getting the most from the T9 Smart Thermostat

Prioritize Rooms (Requires optional Wireless Room Sensor accessory)

Prioritize a speciﬁc room or multiple rooms, or let comfort follow your move using built-in motion

detection.

Control on the Go

Adjust your thermostat from anywhere using your tablet or smartphone.

Save Energy

With geofencing, you can save money on the most expensive part of your energy bill while you’re

away.

Simple Installation

The thermostat automatically programs itself. Just answer a few simple questions and you’ll be up

and running in no time.

WholeHome Range (Requires optional Wireless Room Sensor accessory)

With up to a 200-foot* range, 20 sensors with temperature, humidity, and occupancy detection can

connect to your thermostat from throughout your home.

*Range can vary based on home construction, wireless interference, and other factors.

Know Your Home Is Safe

Get customizable alerts on your mobile device such as when the basement is so cold a pipe could

burst, or if the baby’s room is getting too hot.

19

Using your thermostat

The screen will wake up by pressing the center area of the displayed temperature.

74

2

18%

Indoor Temperature

Displays the current

indoor temperature.

Adjust Temperature

Touch the up and down

arrows to set your desired

temperature.

Current Priority

Displays the type of priority and

number of rooms being prioritized.

Extend your thermostat’s reach with

additional Wireless Room Sensors.

Menu

Contains features such

as mode, fan, schedule,

priority, and other

thermostat settings.

Indoor Humidity

Displays the current

indoor humidity.

Desired Temperature

Displays the desired

temperature.

20

Using Priority

(Requires optional Wireless Room Sensor accessory)

Priority creates an average temperature in your home based on speciﬁc rooms. This allows you to

prioritize comfort where you want it.

From the Home screen, select MENU, then Priority.

Selected Rooms

Rooms you manually select create an average

temperature in your home.

Unselected Room

Will not contribute to the average temperature.

Selected Room

Will contribute to the average temperature.

72 72

Active Rooms

Rooms with detected motion are automatically

selected to create an average temperature in

your home.

Room without Activity

No motion is detected. Will not contribute to

the average temperature.

Room with Activity

Motion is detected. Will contribute to the

average temperature.

La page charge ...

Honeywell RCHT9610WFSW2003/U Guide d'installation

Ce manuel convient également à

Honeywell RCHT9610WFSW2003/U Guide d'installation

dans d''autres langues

Documents connexes

Autres documents