Beko MWOTR24100SS Guide d'installation
- Catégorie
- Hottes
- Taper
- Guide d'installation
MWOTR24100SS
TINSEB---MRR0
Over The Range
Microwave Oven
Installation Manual
CONTENTS
1 IMPORTANT SAFETY INSTRUCTIONS .................3
2 GENERAL INFORMATION .....................................4
HOOD EXHAUST ....................................................4
OUTSIDE TOP EXHAUST .....................................4
OUTSIDE REAR EXHAUST ...................................4
EXHAUST CONNECTION ......................................5
MAXIMUM DUCT LENGTH .....................................5
ELBOWS, TRANSITIONS, WALL AND
ROOF CAPS, ETC. ................................................5
PARTS INCLUDED .................................................6
INSTALLATION ACCESSORIES .............................6
TOOLS YOU WILL NEED .......................................6
MOUNTING SPACE ................................................7
3 STEP-BY-STEP INSTALLATION GUIDE ................ 8
PLACEMENT OF THE MOUNTING PLATE ............ 8
INSTALLATION TYPES (CHOOSE A, B OR C) ....12
2 / 24 EN Over The Range Microwave Oven / Installation Manual
BEFORE YOU BEGIN
Read all instructions thoroughly before installing the
Over-the-Range Microwave Oven.
Note to Installer – Leave these instructions with the
consumer.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills. We recommend that two
people install this microwave oven.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered
under the warranty.
• If a new electrical outlet is required, its installation should
be completed by a qualied electrician before the Over-
the-Range Microwave oven is installed. See ELECTRICAL
GROUNDING INSTRUCTIONS section.
Note to Consumer – Keep these instructions for future
reference.
• Save these instructions for local inspector’s use.
• Observe all governing codes and ordinances.
ELECTRICAL
GROUNDING
INSTRUCTIONS
THIS APPLIANCE MUST BE PROPERLY GROUNDED TO
AVOID SEVERE OR FATAL SHOCK. PLEASE READ
CAREFULLY.
This appliance must be grounded. This oven is equipped with
a cord having a grounding wire with a grounding plug. It must
be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical
Code and local codes and
ordinances. In the event of
an electrical short circuit,
grounding reduces risk of
electric shock by providing
an escape wire for the electric
current.
Ensure proper
ground before
use
WARNINGWARNING Improper use of the grounding plug can result
in risk of electric shock.
The oven is equipped with a 3-prong grounding plug. NEVER
cut or remove the grounding pin from the plug.
The Power Supply Cord and plug must be connected to
a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch
circuit, single grounded receptacle. The receptacle should
be located inside the cabinet directly above the Microwave
Oven/Hood mounting location.
Note: If you have any questions about the grounding or
electrical instructions, consult a qualied electrician or
serviceperson. Neither Beko nor the dealer can accept any
liability for damage to the oven or personal injury resulting
from failure to observe the correct electrical connection
procedures.
CAUTIONCAUTION FOR PERSONAL SAFETY
• Remove the house fuse or open the circuit breaker before
beginning installation to avoid severe or fatal shock injury.
• The mounting surface must be capable of supporting
the cabinet load, in addition to the added weight of this
50–70 lb (22.6–31.7 kg) product, plus additional oven
loads of up to 50 lb (22.6 kg) for a total weight of 100–120
lb (45.2–54.3 kg).
• This product cannot be installed in cabinet arrangements
such as an island or a peninsula. It must be mounted to
BOTH a top cabinet AND a wall.
• For easier installation and personal safety, we recommend
that two people install this microwave oven.
IMPORTANT SAFETY INSTRUCTIONS
1
3 / 24 ENOver The Range Microwave Oven / Installation Manual
HOOD EXHAUST
Note: Read the next two pages only if you plan to vent your
exhaust to the outside. If you plan to recirculate the air back
into the room, proceed to page 5.
All ductwork must be metal. DO NOT use plastic duct. Check
that all connections are made securely.
OUTSIDE TOP EXHAUST
(EXAMPLE ONLY)
The following chart describes an example of one possible
ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH X
NUMBER USED
EQUIVALENT
LENGTH
Roof Cap
24 ft (7.3 m)
x 1
24 ft
(7.3 m)
12 ft (3.7 m)
Straight Duct
(6"/15.24 cm
Round)
12 ft (3.7 m)
x 1
12 ft
(3.7 m)
Rectangular-to-
Round
Transition
Adapter*
5 ft (1.5 m)
x 1
5 ft
(1.5 m)
Total Length 41 ft (12.5 m)
Equivalent lengths of duct pieces are based on actual tests
and reect requirement for good venting performance with
any vent hood.
*IMPORTANT: If a rectangular-to-round transition adapter
is used, cut the corners of the damper with tin snips to allow
free movement of the damper.
OUTSIDE REAR EXHAUST
(EX AMPLE ONLY)
The following chart describes an example of one possible
ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH X
NUMBER USED
EQUIVALENT
LENGTH
Wall Cap
40 ft (12.2 m)
x 1
40 ft
(12.2 m)
3 ft (91.4 cm)
Straight Duct
(31/4" x 6"/
8.25 x 15.24 cm
Round)
3 ft (91.4 cm)
x 1
3 ft
(91.4 cm)
90˚ Elbow
10 ft (4 m)
x 2
20 ft
(6.1 m)
Total Length 63 ft (19.2
m)
Equivalent lengths of duct pieces are based on actual tests
and reect requirement for good venting performance with
any vent hood.
Note: To ensure adequate space for the exhaust, align
exhaust between wall-studs or designate a space to
accommodate exhaust between studs at the time of wall
construction.
GENERAL INFORMATION
2
4 / 24 EN Over The Range Microwave Oven / Installation Manual
If you need to install ducts, note that the total duct length
of 3 1/4" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm)
diameter round duct should not exceed 140 equivalent
feet (42.7 m).
Outside ventilation requires a HOOD EXHAUST DUCT.
Read the following carefully.
It is important that venting be installed using the most
direct route and with as few elbows as possible. This
ensures clear venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
EXHAUST CONNECTION
The hood exhaust has been designed to connect with a
standard 3 1/4" x 10" (8.3 x 25.4 cm) rectangular duct.
If a round duct is required, a rectangular-to-round transiting
adapter must be used. Do not use less than a 6" (15.2 cm)
diameter duct.
MAXIMUM DUCT LENGTH
For satisfactory air movement, the total duct length of
3 1/4" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm)
diameter round duct should not exceed 140 equivalent feet.
ELBOWS, TRANSITIONS, WALL AND ROOF
CAPS, ETC.
Elbows, adapters, wall and roof caps, etc. present additional
resistance to air ow and are equivalent to a section of
straight duct which is longer than their actual physical size.
When calculating the total length, add the equivalent lengths
of all transitions and adapters plus the length of all straight
duct sections. The chart on the right shows the approximate
measurement of equivalent length of some typical ductwork
parts.
Use the values in the chart for calculating total ductwork,
which should be less than 140 equivalent feet (42.7 m).
Equivalent lengths of duct pieces are based on actual tests
and reect requirements for good venting performance with
any vent hood.
IMPORTANT: If a rectangular-to-round transition adapter is
used, cut the corners of the damper with tin snips to allow
free movement of the damper.
DUCT PIECES
EQUIVALENT
LENGTH X
NUMBER USED
EQUIVALENT
LENGTH
EXAMPLE ONLY (VALUES)
Rectangular-to-Round
Transition Adapter
5 ft (1.5 m)
x 1
5 ft
(1.5 m)
Wall Cap
40 ft (12.19 m)
x 1
40 ft
(12.19 m)
90˚ Elbow
10 ft (3 m)
x 1
10 ft
(3 m)
45° Elbow
5 ft (1.5 m)
x 1
5 ft
(1.5 m)
90° Elbow
25 ft (7.6 m)
x 1
25 ft
(7.6 m)
45° Elbow
5 ft (1.5 m)
x 1
5 ft
(1.5 m)
Roof Cap
24 ft (7.3 m)
x 1
24 ft
(7.3 m)
Straight Duct
3 ¼" x 6" (8.3 x 15 cm)
Round
1 ft (30.5 cm)
x 5
5 ft
(1.5 m)
Example Total Ductwork 119 ft (36.3 m)
GENERAL INFORMATION
2
5 / 24 ENOver The Range Microwave Oven / Installation Manual
PARTS INCLUDED
PART NAME & PART CODE QTY.
Mounting Plate
213259000685 1
Exhaust Adapter
213999001159 1
Top Cabinet Template
525049000030 1
Rear Wall Template
525049000042 1
Installation
Instructions
Installation Instructions
TINSKB315MRR0 1
Separately Packed Grease
Filter
213999001028
2
Charcoal Filter
213999001066 1
INSTALLATION ACCESSORIES
PART NAME
PART CODE 203129000066 QTY.
Lag Screw
1/4" x 2" (0.63 x 5.1 cm) 2
Wing Nut 2
Toggle Bolt
3/16" x 3" (0.5 x 7.6 cm) 2
Cabinet Mounting Bolt
1/4" x 3" (0.6 x 7.6 cm) 2
Nylon Grommet
(for metal cabinets) 1
Washer 2
Sheet Metal Screw 2
You will nd the installation accessories contained in a
packet with the unit. Check to make sure you have all these
parts.
Note: Some extra parts are included.
TOOLS YOU WILL NEED
#1 and #2 Phillips
screwdrivers
Pencil Ruler or tape
measure
straight edge
Tin snips
(to cut damper,
if needed)
Scissors
(to cut template,
if needed)
Electric drill with
3⁄16" (4.8 mm),
1⁄2" (1.23 mm) and
5⁄8" (16 mm) bits
Gloves Safety goggles Duct and masking
tape
Saw level
(saber, hole or
keyhole)
Carpenter
square
(optional)
Filler blocks or
scrap wood pieces
(for top cabinet
spacing in recessed
bottom
cabinet installations,
if needed)
Level Edge-to-edge stud
nder or Hammer
(optional)
GENERAL INFORMATION
2
6 / 24 EN Over The Range Microwave Oven / Installation Manual
MOUNTING SPACE
Backsplash
17 1/8"
(43.49 cm) 33"
(83.82 cm)
min.
24" (61 cm)
Bottom edge of cabinet
needs to be 33" (83.82 cm)
or more from the cooking surface
15" (38.1 cm) max.*
69" (1.5 m)
or more
from the floor
to the top of
the microwave
Notes:
• The space between the cabinets must be 24" (61 cm) wide and free of obstructions.
• The maximum depth of the cabinets or wall on either side of the Microwave Oven is 15" (38.1 cm). If the depth is greater
than 15" (38.1 cm), the door will not open properly and the door handle opening may not be accessible.
• If you are going to vent your microwave oven to the outside, see Hood Exhaust Section for exhaust duct preparation.
• When installing the microwave oven beneath smooth, at cabinets, be careful to follow the instruction for power cord clear-
ance. Make sure that you leave enough space for the power cord clearance.
* The maximum depth of the cabinets or wall on either side of the Microwave Oven is 15" (38.1 cm). If the depth is greater
than 15" (38.1 cm), the door will not open properly and the door handle opening may not be accessible.
GENERAL INFORMATION
2
7 / 24 ENOver The Range Microwave Oven / Installation Manual
PLACEMENT OF THE MOUNTING PLATE
A. REMOVE THE MICROWAVE OVEN AND MOUNTING
PLATE FROM CARTON
1. Open the carton and remove the upper foam from the box,
but remember to keep the accessories.
2. Pull the oven out of the carton and remove the plastic
bag carefully.
3. Take the mounting bracket out from the upper foam.
The upper foam
Carton
Oven
Plastic bag
B. FIND THE WALL STUDS
THE MICROWAVE MUST BE MOUNTED TO AT LEAST
ONE WALL STUD.
1. Find the wall studs using either a wall stud nder (a
magnetic device for locating nails) or a hammer to tap
lightly across the mounting surface to nd a solid sound
indicating a wall stud location.
Wall studs
Wall studs center
2. After locating the stud(s), nd the center by probing the
wall with a small nail to nd the edges of the wall stud.
3. Place a mark halfway between the edges. The center of
any adjacent wall studs should be 16" (40.6 cm) or 24"
(61 cm) from this mark.
4. Draw a line down the center of the wall studs.
STEP-BY-STEP INSTALLATION GUIDE
3
8 / 24 EN Over The Range Microwave Oven / Installation Manual
C. DETERMINE TOP LINE OF REAR WALL TEMPLATE LOCATION UNDER YOUR CABINET
The bottom of the cabinet has three types:
BENEATH FLAT BOTTOM CABINET
Front
Rear
TOP LINE OF REAR WALL TEMPLATE
TOP LINE OF REAR WALL TEMPLATE
At least 24"
STEP-BY-STEP INSTALLATION GUIDE
3
9 / 24 ENOver The Range Microwave Oven / Installation Manual
BENEATH FRAMED RECESSED CABINET
TOP LINE OF REAR WALL TEMPLATE
Front
Rear
TOP LINE OF REAR WALL TEMPLATE
Must align with the back frame
of cabinet boom
STEP-BY-STEP INSTALLATION GUIDE
3
10 / 24 EN Over The Range Microwave Oven / Installation Manual
BENEATH FRAMED RECESS BOTTOM CABINET WITH FRONT OVERHANG
TOP LINE OF REAR WALL TEMPLATE
Front
Rear
TOP LINE OF REAR WALL TEMPLATE
distance as the front overhang
STEP-BY-STEP INSTALLATION GUIDE
3
11 / 24 ENOver The Range Microwave Oven / Installation Manual
THE MICROWAVE MUST BE LEVEL
Use a level to make sure the cabinet bottom is level. If
the cabinets have a front overhang only, with no back or
side frame, the top line of Rear Wall Template must align
with below cabinet bottom, the same distance as the front
overhang depth. This will keep the microwave level.
1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall, an equal distance
below the cabinet bottom as the inside depth of the front
overhang.
3. For this type of installation with front overhang only, align
top line of Rear Wall Template with this horizontal line,
not touching the cabinet bottom as described in step D.
Note: Your cabinets may have decorative trim that interferes
with the microwave installation. Remove the decorative trim
to install the microwave properly and to make it level.
D. ALIGN TOP LINE OF REAR WALL TEMPLATE
Area E
Center line
CAUTION
Wear gloves to avoid cutting ngers on sharp
edges.
1. Using tape measure, draw a vertical line on the wall at the
center of the 24" (61 cm) wide space.
2. Tape the Rear Wall Template on the cabinet wall, align the
center markers on the Rear Wall Template to the center
line on wall, making sure it is level and that the top line of
the Rear Wall Template is butted up against the bottom
edge of the upper cabinet.
3. While taping the Rear Wall Template on the wall, draw
circles on the wall at hole A, B, C (see illustration above/
actual plate marked with arrows). THREE HOLES MUST
BE USED FOR MOUNTING. (If there are 2 wall studs in
right and left side based on center line, four holes must
be used for mounting.)
4. Remove the Rear Wall Template and check the marking
based on the actual mounting plate (center line, holes
A, B, C).
5. Drill holes on the circle marks (A, B, C). Drill a 3/16" (4.7
mm) hole at C for lag screw and two 5/8" (15.88 mm) holes
at A and B for toggle bolts.
Note: DO NOT MOUNT THE PLATE AT THIS TIME.
6. If the Rear Wall Template is damaged or unusable, mea-
sure and mark the wall with the dimensions described in
step E.
E. MARK REAR WALL OF THE CABINET WITHOUT
REAR WALL TEMPLATE
1. The bottom edge line of Mounting Plate must be 17 1/8"
(435 mm) from the bottom edge line of upper cabinet and
must be level.
2. Mounting plate end holes must be 16 11/16" (423.8 mm)
from the bottom edge line of upper cabinet and must be
on a equal line with each other. They must each be 9 3/8"
(237.8 mm) from the center line.
Bottom edge line of upper cabinet
Mounting plate end hole
(right/left)
16 11/16"
(423.8 mm)
17 1/8"
(435 mm)
Bottom edge line of
mounting plate
9 3/8"
(237.8 mm)
9 3/8"
(237.8 mm)
INSTALLATION TYPES
(CHOOSE A, B OR C)
This microwave oven is designed for adaptation to the fol-
lowing three types of ventilation:
A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)
See page 12.
Adapter in place
for outside top exhaust
B. OUTSIDE REAR EXHAUST (HORIZONTAL DUCT)
See page 14.
STEP-BY-STEP INSTALLATION GUIDE
3
12 / 24 EN Over The Range Microwave Oven / Installation Manual
C. RECIRCULATING (NON-VENTED DUCTLESS)
See page 18.
A. OUTSIDE TOP EXHAUST (VERTICAL DUCT) DEFAULT
Installation overview
A1. Attach the mounting plate to the wall
A2. Use Top Cabinet Template for preparation of top cabinet
A3. Check for proper damper operation
A4. Mount the microwave oven
A5. Adjust the exhaust adapter
A6. Connect ductwork
A1.
ATTACH MOUNTING PLATE TO THE WALL
Attach the mounting plate to the wall using the wing nuts and
toggle bolts. At least one lag screw must be used to attach
the mounting plate to a wall stud.
1. Insert the toggle bolts into the mounting plate through the
holes designed to go into drywall and attach the wing nuts
to 3⁄4" (1.9 cm) onto each toggle bolt.
2. Place the mounting plate against the wall and insert the
wing nuts into the holes in the wall to mount the plate.
CAUTION
Be careful to avoid pinching ngers
between the back of the mounting plate and the wall.
3. Tighten all bolts. Pull the mounting plate away from the
wall to help tighten the bolts.
5/8"
Wall
Toggle
Bolt
Wing nut
Bolt end
Spacing for toggles more
than wall thickness
STEP-BY-STEP INSTALLATION GUIDE
3
13 / 24 ENOver The Range Microwave Oven / Installation Manual
A2.
USE TOP CABINET TEMPLATE FOR PREPARATION
OF TOP CABINET
Drill holes for the top support screws, a hole large enough
for the power cord to t through and a cutout large enough
for the exhaust adapter.
1. Read the instructions on the Top Cabinet Template.
2. Tape the template underneath the top cabinet bottom.
3. Drill the holes, following the instructions on the Top
Cabinet Template.
CAUTION
Wear safety goggles when drilling holes in
the cabinet bottom.
A3.
CHECK FOR PROPER DAMPER OPERATION
1. Place the microwave in its upright position with the top of
the unit facing up.
2. The exhaust adapter is only used for top exhaust and
rear outside exhaust. The exhaust adapter is not used on
models vented for recirculation exhaust.
3. Make sure tape securing damper is removed and damper
pivots easily before mounting microwave.
Back of microwave
Damper
Blower plate
Exhaust adapter (not included on models shipped for recirculation exhaust)
4. Attach the exhaust adapter to the blower plate by sliding
it into the guides. Secure the adapter with one provided
Sheet Metal Screw.
Sheet metal screw
Guide
Blower plate
Guide
5. You will need to make adjustment to ensure proper align-
ment with your house exhaust duct after the microwave
is installed.
A4.
MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL SAFETY,
WE RECOMMEND THAT TWO PEOPLE INSTALL THIS
MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during installation.
If ller blocks are not used, outer case damage may occur
from over tightening screws.
Note: If your cabinet is metal, use the nylon grommet
around the power cord hole to prevent cutting of the cord.
We recommend using ller blocks if the cabinet front hangs
below the cabinet bottom shelf.
When mounting the microwave oven, thread power cord
through hole in bottom of top cabinet. Keep it tight throughout
steps 1–4. Do not pinch cord or lift oven by pulling cord.
1. Lift microwave, tilt it forward and hook slots at back bottom
edge onto four lower tabs of mounting plate.
2. Rotate front of oven up against cabinet bottom.
3. Attach the microwave oven to the top cabinet.
4. Insert two cabinet mounting bolts through outer top cabinet
holes. Temporarily secure the oven by turning the screw
at least two full turns after the threads have engaged (it
will be completely tightened later). Be sure to keep power
cord tight. Be careful not to pinch the cord, especially when
mounting ush to the bottom of cabinet.
Nylon grommet
Metal cabinet
Power cord
Power cord
hole
Turn two full turns on each screw
Cabinet mounting bolt
Washer
STEP-BY-STEP INSTALLATION GUIDE
3
14 / 24 EN Over The Range Microwave Oven / Installation Manual
The Filler Block is only used for recessed cabinet and
front overhang cabinet (see the type of the cabinet on on
pages 8–10). Place the Filler Block to the cabinet bottom
before installing the oven.
5. Tighten the outer two screws to the top of the microwave
oven. While tightening screws, hold the microwave oven
in place against the wall and the top cabinet.
Cabinet front
Equivalent to
depth of cabinet
recess
Cabinet bottom
Filler block
Cabinet mounting bolt
Microwave oven top
Washer
6. Install grease lters. See the Use & Care Manual packed
with the microwave.
A5.
ADJUST THE EXHAUST ADAPTER
Open the top cabinet and adjust the exhaust adapter to
connect to the house duct.
Damper
Blower Plate
Back of
microwave
For front-to-back or
side-to-side adjustment,
slide the exhaust
adapter as needed
A6.
CONNECT DUCTWORK
1. Extend the house duct down to connect to the exhaust
adapter.
2. Seal exhaust duct joints using duct tape.
House duct
B. OUTSIDE REAR EXHAUST (HORIZONTAL DUCT)
Installation overview
B1. Prepare the Rear Wall Template for outside back exhaust
B2. Attach the mounting plate to the wall
B3. Use Top Cabinet Template for preparation of top cabinet
B4. Adapt microwave blower for outside back exhaust
B5. Mount the microwave oven
STEP-BY-STEP INSTALLATION GUIDE
3
15 / 24 ENOver The Range Microwave Oven / Installation Manual
B1.
PREPARE THE REAR WALL TEMPLATE FOR
OUTSIDE BACK EXHAUST
You need to cut a 12" x 4" (30.5 x 10.2 cm) rectangular
opening in the Rear Wall Template for outside exhaust.
1. Read the instructions on the Rear Wall Template.
2. Tape it to the rear wall, lining up with the holes previously
drilled for holes A and B in the wall plate.
3. Cut the opening, following the instructions of the Rear
Wall Template.
B2.
ATTACH MOUNTING PLATE TO THE WALL
Attach the mounting plate to the wall using the wing nuts and
toggle bolts. At least one lag screw must be used to attach
the mounting plate to a wall stud.
1. Insert the toggle bolts into the mounting plate through the
holes designed to go into drywall and attach the wing nuts
to 3⁄4" (1.9 cm) onto each toggle bolt.
2. Place the mounting plate against the wall and insert the
wing nuts into the holes in the wall to mount the plate.
CAUTIONCAUTION Be careful to avoid pinching ngers between
the back of the mounting plate and the wall.
3. Tighten all bolts. Pull the mounting plate away from the
wall to help tighten the bolts.
TO USE TOGGLE BOLT
Mounting
plate
Wall
Toggle
Bolt
Wing nut
Bolt end
Spacing for toggles more
than wall thickness
5/8"
B3.
USE TOP CABINET TEMPLATE FOR PREPARATION
OF TOP CABINET
You need to drill holes for the top support screws and a hole
large enough for the power cord to t through.
• Read the instructions on the Top Cabinet Template.
• Tape it underneath the top cabinet bottom.
• Drill the holes, following the instructions on the Top
Cabinet Template.
CAUTION
Wear safety goggles when drilling holes in
the cabinet bottom.
STEP-BY-STEP INSTALLATION GUIDE
3
16 / 24 EN Over The Range Microwave Oven / Installation Manual
B4.
ADAPT MICROWAVE BLOWER FOR OUTSIDE REAR
EXHAUST
1. Remove and save screw that holds blower motor to
microwave. Lift up the blower plate.
Back of
Blower plate screw
Blower motor screw
microwave
Blower motor
2. Carefully pull out the blower unit. The wires will extend far
enough to allow you to adjust the blower unit.
BEFORE: Fan blade
openings facing UP
3. Remove Part A with tin snips.
Part A
4. Rotate blower unit counterclockwise 90°.
Before rotation After rotation
Back of microwave Back of microwave
5. Place the blower unit back into the opening.
End A
End B
AFTER: Fan blade
openings facing BACK
CAUTIONCAUTION Do not pull or stretch the blower unit wiring.
Make sure the wires are not pinched.
Note: The blower unit exhaust openings should match
exhaust openings on rear of microwave oven.
6. Replace the blower plate in the same position.
7. Attach the exhaust adapter to the rear of the oven by
sliding it into the guides at the top center of the back of
the oven.
Push in securely until it is in the lower blower motor screw.
Take care to assure that the damper hinge is installed
so that it is at the top and that the damper swings freely.
Blower motor screws
Adapter
Back of
microwave
Guide
Guide
8. Secure the blower motor unit to the microwave with screws
as before.
Blower plate
Adapter
Back of
microwave
Blower motor screws
9. Secure the blower plate to the microwave with screws.
Replace the blower plate in the same position.
Blower plate screw
Adapter
Blower Plate
Back of
microwave
Blower plate &
adapter screw
STEP-BY-STEP INSTALLATION GUIDE
3
17 / 24 ENOver The Range Microwave Oven / Installation Manual
B5.
MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL SAFETY,
WE RECOMMEND THAT TWO PEOPLE INSTALL THIS
MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during installation.
If ller blocks are not used, outer case damage may occur
from over tightening screws.
Note: If your cabinet is metal, use the nylon grommet
around the power cord hole to prevent cutting of the cord.
We recommend using ller blocks if the cabinet front hangs
below the cabinet bottom shelf.
When mounting the microwave oven, thread power cord
through hole in bottom of top cabinet. Keep it tight throughout
steps 1–4. Do not pinch cord or lift oven by pulling cord.
1. Lift microwave, tilt it forward and hook slots at back bottom
edge onto four lower tabs of mounting plate.
2. Rotate front of oven up against cabinet bottom.
3. Attach the microwave oven to the top cabinet.
4. Insert two cabinet mounting bolts through outer top cabinet
holes. Temporarily secure the oven by turning the screw
at least two full turns after the threads have engaged (it
will be completely tightened later). Be sure to keep power
cord tight. Be careful not to pinch the cord, especially when
mounting ush to the bottom of cabinet.
Nylon grommet
Metal cabinet
Power cord
Power cord
hole
Turn two full turns on each screw
Cabinet mounting bolt
Washer
The Filler Block is only used for recessed cabinet and
front overhang cabinet (see the type of the cabinet on
pages 8–10). Place the Filler Block to the cabinet bottom
before installing the oven.
5. Tighten the outer two screws to the top of the microwave
oven. While tightening screws, hold the microwave oven
in place against the wall and the top cabinet.
Cabinet front
Equivalent to
depth of cabinet
recess
Cabinet bottom
Filler block
Cabinet mounting bolt
Microwave oven top
Washer
6. Install grease lters. See the Use & Care Manual packed
with the microwave.
STEP-BY-STEP INSTALLATION GUIDE
3
18 / 24 EN Over The Range Microwave Oven / Installation Manual
C. RECIRCULATING (NON-VENTED DUCTLESS)
Installation overview
C1. Attach the mounting plate to the wall
C2. Use Top Cabinet Template for preparation of top cabinet
C3. Adapt blower for recirculation
C4. Mount the microwave oven
C5. Change the charcoal lter
C1.
ATTACH MOUNTING PLATE TO THE WALL
Attach the mounting plate to the wall using the wing nuts and
toggle bolts. At least one lag screw must be used to attach
the mounting plate to a wall stud.
1. Insert the toggle bolts into the mounting plate through the
holes designed to go into drywall and attach the wing nuts
to 3⁄4" (1.9 cm) onto each toggle bolt.
2. Place the mounting plate against the wall and insert the
wing nuts into the holes in the wall to mount the plate.
CAUTIONCAUTION Be careful to avoid pinching ngers between
the back of the mounting plate and the wall.
3. Tighten all bolts. Pull the mounting plate away from the
wall to help tighten the bolts.
5/8"
Wall
Toggle
Bolt
Wing nut
Bolt end
Spacing for toggles more
than wall thickness
C2.
USE TOP CABINET TEMPLATE FOR PREPARATION
OF TOP CABINET
You need to drill holes for the top support screws and a hole
large enough for the power cord to t through.
• Read the instructions on the Top Cabinet Template.
• Tape the template underneath the top cabinet bottom.
• Drill the holes, following the instructions on the Top
Cabinet Template.
CAUTIONCAUTION Wear safety goggles when drilling holes in the
cabinet bottom.
STEP-BY-STEP INSTALLATION GUIDE
3
19 / 24 ENOver The Range Microwave Oven / Installation Manual
C3. ADAPT BLOWER FOR RECIRCULATION
1. Remove and save screw that holds blower motor to
microwave. Lift up the blower plate.
Back of
Blower plate screw
Blower motor screw
microwave
Blower motor
2. Carefully pull out the blower unit. The wires will extend far
enough to allow you to adjust the blower unit.
BEFORE: Fan blade
openings facing UP
3. Rotate blower unit counterclockwise 90°.
Before rotation After rotation
Back of microwave Back of microwave
4. Place the blower unit back into the opening.
AFTER: Fan blade
openings facing FRONT
Back of microwave
CAUTIONCAUTION Do not pull or stretch the blower unit wiring.
Make sure the wires are not pinched.
Note: The blower unit exhaust openings should match
exhaust openings on rear of microwave oven.
5. Replace the blower plate in the same position.
C4.
MOUNT THE MICROWAVE OVEN
FOR EASIER INSTALLATION AND PERSONAL SAFETY,
WE RECOMMEND THAT TWO PEOPLE INSTALL THIS
MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during installation.
If ller blocks are not used, case damage may occur from
over tightening screws.
Note: If your cabinet is metal, use the nylon grommet
around the power cord hole to prevent cutting of the cord.
We recommend using ller blocks if the cabinet front hangs
below the cabinet bottom shelf.
When mounting the microwave oven, thread power cord
through hole in bottom of top cabinet. Keep it tight throughout
steps 1–4. Do not pinch cord or lift oven by pulling cord.
1. Lift microwave, tilt it forward and hook slots at back bottom
edge onto four lower tabs of mounting plate.
2. Rotate front of oven up against cabinet bottom.
3. Attach the microwave oven to the top cabinet.
4. Insert two cabinet mounting bolts through outer top cabinet
holes. Temporarily secure the oven by turning the screw
at least two full turns after the threads have engaged (it
will be completely tightened later). Be sure to keep power
cord tight. Be careful not to pinch the cord, especially when
mounting ush to the bottom of cabinet.
Nylon grommet
Metal cabinet
Power cord
Power cord
hole
STEP-BY-STEP INSTALLATION GUIDE
3
20 / 24 EN Over The Range Microwave Oven / Installation Manual
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Beko MWOTR24100SS Guide d'installation
- Catégorie
- Hottes
- Taper
- Guide d'installation
dans d''autres langues
- English: Beko MWOTR24100SS Installation guide
Autres documents
-
Samsung SMH1816B/XAC Guide d'installation
-
-
-
Samsung ME21M706BAG/AC Guide d'installation
-
-
Samsung ME17H703SHS/AC Guide d'installation
-
Samsung 1133098 Guide d'installation
-