Chief KRA235B Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
KRA235 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the KRA235 does not exceed 25 lbs
(11.34 kg) or the weight limit of the mount to which it is
attached. All K3 and K4 Series mounts have a weight limit of
15 lbs (6.8 kg) per display.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
The KRA235 accessory is designed to be an
accessory for the following K3 and K4 Series array mounts:
K3F220, K3F310, K3G220, K3G310, K3G320, K4W210,
K4W310, K4G210, K4G310, K4G220, K4G320, K4S210,
K4S310, K4G410, K4G510, K4G610, K4G420, K4G520 and
K4G620. Do NOT attempt to use the KRA235 accessory with
any other type of mount!
--SAVE THESE INSTRUCTIONS--
Installation Instructions KRA235
3
DIMENSIONS
4.72
120.0
3.94
100.0
3.94
100.0
DIMENSIONS: INCHES
[MILLIMETERS]
KRA235 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions KRA235
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
A (1)
[Height adjustable accessory]
B (4)
1/2"
M4 x 20mm
C (4)
KRA235 Installation Instructions
6
ASSEMBLY AND INSTALLATION
IMPORTANT ! :
The KRA235 accessory is designed to be an
accessory for the following K3 and K4 Series array mounts:
K3F220, K3F310, K3G220, K3G310, K3G320, K4W210,
K4W310, K4G210, K4G310, K4G220, K4G320, K4S210,
K4S310, K4G410, K4G510, K4G610, K4G420, K4G520 and
K4G620. Do NOT attempt to use the KRA235 accessory with
any other type of mount!
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the KRA235 does not exceed 25 lbs
(11.34 kg) or the weight limit of the mount to which it is
attached. All K3 and K4 Series mounts have a weight limit of
15 lbs (6.8 kg) per display.
1. Carefully place display face down on protective surface.
2. Use four M4 x 20mm Phillips flat head screws (C) and four
1/2" spacers (B) to secure KRA235 to back of display. (See
Figure 1)
Figure 1
3. Remove lower two pre-installed Phillips screws from
KRA235. Set screws aside for re-use. (See Figure 2)
IMPORTANT ! : Make sure washers under removed
screws stay in position over mounting holes. (See Figure
2)
4. Loosen upper two pre-installed Phillips screws on KRA235.
(See Figure 2)
Figure 2
5. Place K3 or K4 head assembly on back of KRA235 mount
and slide until the two upper screws are positioned in the
upper 75mm x 75mm mounting holes of the K3/K4 head
assembly. (See Figure 3)
Figure 3
2
(A)
(C) x 4
2
(B) x 4
x 2
3
4
x 2
(A)
washers must stay
in position
(A)
K3/K4 mounting
head assembly
5
5
mounting
75mm x 75mm
holes
Installation Instructions KRA235
7
6. Tighten upper two screws. (See Figure 4)
7. Re-install two Phillips screws that were removed in Step 4
through lower inside mounting holes on K3/K4 head
assembly. (See Figure 4)
Figure 4
8. Re-install K3/K4 mounting head to array arm.
Height Adjustment
1. Turn height adjustment knob clockwise to raise display
level. (See Figure 5)
2. Turn height adjustment knob counter-clockwise to lower
display level. (See Figure 5)
Figure 5
(A)
K3/K4 mounting
head assembly
6
x 2
x 2
7
2
1
1
2
KRA235 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002752 Rev00
2015 Milestone AV Technologies
www.chiefmfg.com
08/15
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief KRA235B Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief KRA235B Installation guide
Documents connexes
-
Chief KRA231W Guide d'installation
-
-
-
-
-
-
-
-
Chief FCA651B Guide d'installation
-