Generac iX800 0057912 Manuel utilisateur

Marque: Generac

Modèle: iX800 0057912

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

www.generac.com or 1-888-GENERAC

iX 800

Digital Inverter Generator Operator's Manual

MODEL: 005791-2

Accessory Box .....................................Inside Front Cover

Introduction .....................................................................1

Read this Manual Thoroughly .........................................1

Safety Rules ...................................................................1

Standards Index.........................................................3

General Information ........................................................4

1.1 Specifications ........................................................4

1.1.1 Emissions Information ...................................4

1.2 Unit Identification ...................................................4

1.2.1 Control Panel .................................................5

Operation ........................................................................5

2.1 Pre-Use Check and Set-up .....................................5

2.2 Starting the Generator ............................................6

2.3 Adding Loads .........................................................6

2.4 Using the FlexPower

™

Switch ................................7

2.5 Shutting Down .......................................................7

2.6 Low Oil Level Shutdown .........................................7

2.7 Fueling the Generator .............................................7

2.7.1 To Fill the Fuel Tank .......................................8

2.8 Adding Engine Oil ...................................................8

2.8.1 To Add Engine Oil to the Crankcase ...............8

Maintenance ...................................................................9

3.1 Generator Maintenance...........................................9

3.2 Generator Maintenance Schedule ...........................9

3.3 Cleaning the Generator ...........................................9

3.4 Engine Maintenance ...............................................9

3.5 Changing the Engine Oil .......................................10

3.6 Changing the Fuel Filter ........................................10

3.7 Changing the Spark Plug ......................................10

3.8 Transportation and Storage ..................................11

Section 4 - Troubleshooting ..........................................12

4.1 Troubleshooting Guide ..........................................12

Notes ............................................................................13

Warranty .......................................................................14

iX 800 Manual del operador del

Generador Inversor Digital .......................................17

iX 800 Manuel d'utilisation du

générateur inverseur numérique ..............................35

ACCESSORY BOX

Check all contents. If any parts are missing or damaged locate an

authorized dealer at 1-888-436-3722.

Contents include:

1 bottle SAE 30 Oil • • Oil Funnel

Spark Plug Wrench • Screwdriver•

Table of Contents

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems,

Inc. This model is a compact, high performance, air-cooled,

engine driven generator designed to supply electrical power to

operate electrical loads where no utility power is available or in

place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the

nearest Authorized Dealer for starting, operating and servicing

procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using the

equipment. We also strongly recommend instructing other users to

properly start and operate the unit. This prepares them if they need

to operate the equipment in an emergency.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

Become familiar with and strictly adhere to all local, state and •

national codes and regulations.

Study all safety warnings in this manual and on the product •

carefully.

Become familiar with this manual and the unit before use.•

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as

follows:

Indicates a hazardous situation or action which, if

not avoided, will result in death or serious injury.

Indicates a hazardous situation or action which, if

not avoided, could result in death or serious injury.

Indicates a hazardous situation or action which,

if not avoided, could result in minor or moderate

injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:

n

This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property of

others.





This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.

GENERAL HAZARDS

Never operate in an enclosed area or indoors. •

For safety reasons, the manufacturer recommends that the •

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

Operate generator only on level surfaces and where it will not be •

exposed to excessive moisture, dirt, dust or corrosive vapors.

Keep hands, feet, clothing, etc., away from drive belts, fans, •

and other moving parts. Never remove any fan guard or shield

while the unit is operating.

Certain parts of the generator get extremely hot during •

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

Do NOT operate generator in the rain.•

Do not alter the construction of the generator or change controls •

which might create an unsafe operating condition.

Never start or stop the unit with electrical loads connected •

to receptacles AND with connected devices turned ON. Start

the engine and let it stabilize before connecting electrical

loads. Disconnect all electrical loads before shutting down the

generator.

When working on this equipment, remain alert at all times. •

Never work on the equipment when physically or mentally

fatigued.

Safety Rules

Never use the generator or any of its parts as a step. Stepping •

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

EXHAUST & LOCATION HAZARDS

Never operate in an enclosed area or indoors! • NEVER use in

the home, or in partly enclosed areas such as garages, even

if doors and windows are open! ONLY use outdoors and far

from open windows, doors, vents, and in an area that will not

accumulate deadly exhaust.

The engine exhaust fumes contain carbon monoxide, which •

can you cannot see or smell. This poisonous gas, if breathed

in sufficient concentrations, can cause unconsciousness or

even death.

Adequate, unobstructed flow of cooling and ventilating air •

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

This exhaust system must be properly maintained. Do nothing •

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

The manufacturer recommends installing a battery operated •

carbon monoxide alarm indoors, according to the manufacturers

instructions.

If you start to feel sick, dizzy, or weak after the generator has •

been running, move to fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poisoning.

ELECTRICAL HAZARDS

The generator produces dangerously high voltage when in •

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected

to the generator. Ensure all appropriate covers, guards and

barriers are in place before operating the generator.

Never handle any kind of electrical cord or device while •

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

The National Electric Code (NEC) requires the frame and external •

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

Use a ground fault circuit interrupter in any damp or highly •

conductive area (such as metal decking or steel work).

Do not use worn, bare, frayed or otherwise damaged electrical •

cord sets with the generator.

In case of accident caused by electric shock, immediately shut •

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE. •

Do not permit smoking, open flames, sparks or heat in the

vicinity while handling gasoline.

Never add fuel while unit is running or hot.• Allow engine to

cool completely before adding fuel.

Never fill fuel tank indoors. • Comply with all laws regulating

storage and handling of gasoline.

Do not overfill the fuel tank. Always allow room for fuel •

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

Wipe up any fuel or oil spills immediately. Ensure that no •

combustible materials are left on or near the generator. Keep the

area surrounding the generator clean and free from debris and

keep a clearance of five (5) feet on all side to allow for proper

ventilation of the generator.

n

Save These Instructions – The manufacturer suggests that these rules for safe operation be copied and

posted near the unit's installation site. Safety should be stressed to all operators and potential operators of

this equipment.

Safety Rules

Do not insert objects through unit’s cooling slots.•

Do not • operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

Keep a fire extinguisher near the generator at all times. •

STANDARDS INDEX

In the absence of pertinent standards, codes, regulations and laws,

the published information listed below may be used as a guideline

for operation of this equipment. Always reference the latest revision

available for the standards listed.

1. NFPA No. 70, NFPA HANDBOOK OF NATIONAL ELECTRIC

CODE.

2. Article X, NATIONAL BUILDING CODE, available from the

American Insurance Association, 85 John Street, New York,

N.Y. 10038.

3. AGRICULTURAL WIRING HANDBOOK, available from the Food

and Energy Council, 909 University Avenue, Columbia, MO

65201.

4. ASAE EP-3634, INSTALLATION AND MAINTENANCE OF

FARM STANDBY ELECTRICAL SYSTEMS, available from the

American Society of Agricultural Engineers, 2950 Niles Road,

St. Joseph, MI 49085.

MODEL NO:

SERIAL NO:

Figure 1 - Generator ID Plate

ID PLATE

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the

State of California to cause cancer, birth defects and

other reproductive harm.

Safety Rules

1.1 SPECIFICATIONS

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . Single Cylinder, 4-Stroke

Engine Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 cc

Starter Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recoil

Fuel Capacity/Type . . . . . . . . . . . . . . . . . . . .0.5 Gal (1.9L)/Unleaded

Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.18 Qt (0.17L)

Runtime Full/Half Load . . . . . . . . . . . . . . . . . . . . . . . . 2.1/3.6 Hours

Spark Plug Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . NGK CR7HSA

Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..030”

Dimensions L x W x H (in) . . . . . . . . . . . . . . . . . . . . . . 18 x 10 x 15

Weight Lb/kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29/13.2

Maximum AC Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800W

Surge AC Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850W

AC Volts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 VAC

Rated AC Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.6 A

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz

THD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0%

Insulation Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class B

Outlets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2) 5-15R

NOTE:

Power output and runtime are influenced by many factors,

some of which are fuel quality, ambient temperature and engine

condition. Output decreases approximately 3.5% for each 1,000

feet above sea level and 1% for every 10 degrees above 60°F.

1.1.1 EMISSIONS INFORMATION

The Environmental Protection Agency (EPA) requires that your

generator comply with exhaust emission standards. This generator

is certified to meet the applicable EPA emission levels. Additional

information regarding the requirements set by EPA is as follows:

The maintenance specifications provided in this manual must be

followed to ensure that your engine complies with the applicable

emission standards for the duration of the engine’s life. This engine

is certified to operate on gasoline. The emission control system on

your generator consists of the following:

Fuel Metering System • Ignition System•

~ Carburetor ~ Spark plug

~ Fuel Pump ~ Ignition module

~ Fuel Lines

Air Induction System•

~ Intake pipe / manifold

~ Air cleaner

The Emissions Compliance Period referred to on the Emissions

Compliance Label indicates the number of operating hours for

which the engine has been shown to meet Federal emission

requirements.

1.2 UNIT IDENTIFICATION (Figure 2)

1. Carrying Handle: Lift the generator by this handle only.

2. Spark Plug Cover: Allows access to the engine spark plug.

3. Fuel System Primer: Used to prime the fuel system for

starting.

4. Fuel Cap Pressure Valve: Allows air to enter the fuel tank to

equalize pressure.

5. Fuel Tank Cap: Access to fuel tank for filling.

6. Control Panel: location of generator controls and output

receptacles.

7. Air Intake Slats: Allows for cooling air to enter the housing.

8. Muffler: Lowers engine exhaust noise.

9. Choke: Cold engine starting aid

10. Left Side Service Cover: Allows access to air filter, fuel filter

and oil fill.

11. Vent Hoses: Hoses allow venting of the crankcase and

carburetor.

12. Fuel Shutoff: Controls fuel supply to the carburetor.

13. Starter Rope: Pull rope for starting engine.

Figure 2 - Unit Identification

General Information

1.2.1 CONTROL PANEL (Figure 3)

14. READY LED (green): Indicates output from the generator

unless there is a low oil or overload condition.

15. OVERLOAD LED (red): Lights up if the generator experiences

a load greater than the rated output, low voltage, overheats or

the powered circuit experiences a short. The output is stopped

even though the engine keeps running.

16. LOW OIL LEVEL LED (yellow): Lights up when oil level is below

safe operating level and the engine shuts down..

17. FlexPower™ Switch: This switch slows the engine speed when

the load is reduced to save fuel and engine wear.

18. 120 VAC Receptacles: Two (2) receptacles for connecting

accessories.

19. Ground (Earth) Connection Lug: Grounding point for the

generator; consult state and local electrical codes before use

(floating ground).

NOTE:

Do not exceed the rated output of the generator.

Figure 3 - Control Panel

2.1 PRE-USE CHECK AND SET-UP

Prior to starting the generator and adding loads, perform the following

tasks:

1. Make sure the generator in on a firm, level, non-combustible surface

with at least five (5) feet of clearance on all sides.

n

Never operate in an enclosed area or indoors!

NEVER use in the home, or in partly enclosed

areas such as garages, even if doors and

windows are open! ONLY use outdoors and far

from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

n

The engine exhaust fumes contain carbon

monoxide, which can you cannot see or smell.

This poisonous gas, if breathed in sufficient

concentrations, can cause unconsciousness or

even death.

n

Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or permit

even partial blockage of ventilation provisions,

as this can seriously affect safe operation of

the generator. The generator MUST be operated

outdoors.

n

This exhaust system must be properly

maintained. Do nothing that might render the

exhaust system unsafe or in noncompliance

with any local codes and/or standards.

n

The manufacturer recommends installing

a battery operated carbon monoxide alarm

indoors, according to the manufacturers

instructions.

n

NEVER use in the home, or in partly enclosed areas

such as garages, campers or trailers. ONLY use

outdoors and far from open windows, doors, vents.

2. Remove the fuel cap and check the fuel level. If fuel is needed, see

the section “FUELING THE GENERATOR”.

3. Remove the left side service cover and check the oil level by

removing the oil filler cap. The oil level should be to the bottom of the

threads on the oil fill pipe. If oil is needed, see the section “ADDING

ENGINE OIL”.

4. Replace and secure the left side service cover.

5. Make sure there are no loads connected to the generator.

6. The National Electric Code (NEC) requires the frame and external

electrically conductive parts of the generator be properly connected

to an approved earth ground. Proper grounding of the generator will

prevent electrical shock in the event of a ground fault condition in the

generator or in connected electrical devices. Proper grounding also

helps dissipate static electricity, which often builds up in unguarded

devices.

7. Local electrical codes may also require proper grounding of the

generator.

Operation

n

Starting the generator with accessories connected

to the 120 VAC outlets will damage the generator

and the connected accessories.

2.2 STARTING THE GENERATOR

Once the fuel and oil levels have been checked and it has been

verified there are no loads connected, the generator may be

started. Turn the FlexPower Switch OFF (O).

1. Open the fuel valve (Figure 4), located below the starter rope

pull, by turning the valve 90° counter-clockwise to the “ON”

(I) position.

Figure 4 - Fuel Valve

TURNING THE FUEL ON

2. Pull up on the center of the fuel fill cap and prime the fuel

system by depressing the plunger up to five (5) times with the

vent closed (Figure 5).

Figure 5 - Prime Fuel System

FUEL

SYSTEM

VENT

PLUNGER

VENT

3. Open the fuel tank vent on the top of the fuel fill cap by turning

the center portion to the “ON” mark (Figure 5).

4. If the engine is cold or has not been run for some time, engage

the choke by pushing the choke lever to the right.

5. Grip the handle for the pull starter and brace your other hand

against the generator. Pull the rope slowly until resistance is

felt, then pull the rope rapidly.

6. If the engine does not start, repeat steps 2-5 until the engine

fires and begins to run.

7. Carefully adjust the choke to approximately the ½ position

until the engine begins to run smoothly, then push the lever all

the way to the left (Figure 6).

8. Make sure the bottom of the generator is not blocked by sand,

leaves, grass, etc. as the cooling vents are located on the

bottom of the unit.

Figure 6 - Adjust Choke

ENGINE CHOKE

OPERATION

OFF

2.3 ADDING LOADS

Once the generator has been running smoothly for 2-3 minutes,

electrical loads can be added.



Do not use worn, bare, frayed or otherwise

damaged electrical cord sets with the

generator. Do not handle any kind of electrical

device while standing in water, while barefoot,

or while hands or feet are wet.

1. There are two grounded 120 VAC duplex outlets on the front

of the generator.

2. DO NOT overload the generator; if the red “overload” LED

lights up and the accessories attached to the generator

stop operating, stop the engine and reduce the load to the

generator. Restart and apply reduced loads.

3. Consult the following table to estimate what can be powered

by the generator.

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Running Watts

*Air Conditioner (12,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . . .1700

*Air Conditioner (24,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . . .3800

*Air Conditioner (40,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6000

Battery Charger (20 Amp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

Circular Saw (6-1/2"). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700

*Clothes Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1750

*Compressor (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000

*Compressor (3/4 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1800

*Compressor (1/2 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1400

Operation

Curling Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 700

*Dehumidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .650

Disc Sander (9") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

Edge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500

Electric Blanket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400

Electric Nail Gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

Electric Range (per element) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1500

Electric Skillet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1250

*Freezer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700

*Furnace Fan (3/5 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .875

*Garage Door Opener. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 to 750

Hair Dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

Hand Drill. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 to 1100

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450

Impact Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500

Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800

Lawn Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

Light Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Microwave Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700 to 1000

*Milk Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1100

Oil Burner on Furnace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . .400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . .225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . .150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .600

Paint Sprayer, Airless (handheld) . . . . . . . . . . . . . . . . . . . . . . . . . . .150

Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 to 200

*Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700

Slow Cooker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . .2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000

*Submersible Pump (1/2 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . .1500

*Sump Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 to 1050

* Allow three (3) times the listed running watts for starting theses devices.

NOTE:

When an electric motor is started, the "OVERLOAD" LED may

light up for up to five (5) seconds (this is normal). If it stays on,

a fault has occured. Remove all loads and shut down generator

to reset the alarm. Restart the generator. If the "OVERLOAD"

LED remains lit, contact a Generac Dealer for assistance.

2.4 USING THE FLEXPOWER™ SWITCH

When the accessories connected to the generator are going to

be used intermittently (such as a hand drill), the FlexPower™

switch can be pushed to the “ON” (I) position. This will lower the

generator engine speed when loads are not being applied, saving

fuel, reducing engine wear and extending runtime.

2.5 SHUTTING DOWN

Once the generator is no longer needed it can be shut down.

1. Switch off any accessories connected to the generator. Unplug

any cords to the 120 VAC duplex outlets.

2. Turn the fuel valve to the “OFF” (O) position (Figure 7). A

switch behind the fuel valve grounds the ignition system,

stopping the engine and the fuel supply is shut off.

3. Close the vent on the fuel cap.

4. Allow the generator to cool before moving or storing.

n

Always allow the generator to cool off before

storing. High temperatures will be present

at the rear of the unit for some time after

shutdown.

Figure 7 - Turn Off Fuel

TURNING THE FUEL OFF

2.6 LOW OIL LEVEL SHUTDOWN

This generator is equipped with a low oil level shut down. If the

oil level in the engine crankcase drops below a pre-determined

level, the engine will stop automatically and the “LOW OIL” LED

will light up.

Remove the Left Side Service Cover and check the oil level of the

engine. Add oil as necessary; refer to see the section “ADDING

ENGINE OIL”.

2.7 FUELING THE GENERATOR

Use care when fueling the generator. Only fill the fuel tank when

the generator is cool and use fresh unleaded gasoline with a

minimum Research Octane Number (RON) of 87.

NOTE:

Do not use any gasoline containing more than 10% Ethanol.

NEVER fill the fuel tank with E85 or a mixture of oil and gasoline

designated for two-cycle engines.





Gasoline is highly FLAMMABLE and its vapors

are EXPLOSIVE. Do not permit smoking, open

flames, sparks or heat in the vicinity while

handling gasoline.

n

Never add fuel while unit is running or hot.

Allow unit to cool entirely before adding fuel.





Do not overfill the fuel tank. Always allow

room for fuel expansion. If tank is over-filled,

fuel can overflow onto a hot engine and cause

FIRE or an EXPLOSION. Wipe up fuel spills

immediately!

Operation

2.7.1 TO FILL THE FUEL TANK

1. Remove the fuel tank cap.

Figure 8 - Fuel Tank Cap

FUEL

TANK

CAP

FILL TANK UNTIL

FUEL IS TWO (2)

INCHES BELOW

THE TOP

2. Add fuel slowly, stopping about 2 inches below the top of the

filler neck.

3. Replace the fuel tank cap. Make sure the valve on the fuel cap

is in the “OFF” position.

4. If the generator is going to be started, refer to the section

“STARTING THE GENERATOR” for additional directions on

priming the fuel system.

2.8 ADDING ENGINE OIL

All oil should meet minimum American Petroleum Institute (API)

Service Class SJ, SL or better. Do not use any aftermarket

additives.

Select the oil's viscosity grade according to the expected operating

temperature, only a little more than one-half quart is needed.

Above 40° F, use SAE 30•

Below 40° F to 10° F, use 10W-30•

Below 10° F, use synthetic 5W-30•

10W-30

10W - 30

SAE 30

Synthetic 5W-30

Synt het i c 5 W-3 0

2.8.1 TO ADD ENGINE OIL TO THE CRANKCASE

1. Place the unit on a firm, level surface.

2. Remove the Left Side Service Cover.

3. Remove the oil fill cap, located on the bottom of the engine

crankcase.

4. Add the recommended engine oil slowly, stopping frequently

to check the level. The full level is the base of the threads in

the filler neck.

5. Replace the oil fill cap and tighten.

6. Always check the oil level before starting the generator

engine.

Figure 9 - Oil Fill

FULL OIL LEVEL

IS THE BOTTOM

OF THESE

THREADS

OIL FILL CAP

n

DO NOT overfill the engine crankcase with

oil. High oil pressure may result, causing

premature engine wear and damage.

Operation

3.1 GENERATOR MAINTENANCE

Proper care will ensure maximum performance of your generator.

Generator maintenance consists of keeping the unit clean and dry.

Operate and store the unit in a clean dry environment where it will

not be exposed to excessive dust, dirt, moisture or any corrosive

vapors.

Cooling air slots in the generator must not become clogged with

snow, leaves, or any other foreign material.

Check the cleanliness of the generator frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible on

its exterior surface.

NOTE:

Never insert any object or tool through the air cooling slots,

even if the engine is not running.

NOTE:

DO NOT use a garden hose to clean generator. Water can enter

the engine fuel system and cause problems. In addition, if water

enters the generator through cooling air slots, some water will

be retained in voids and crevices of the rotor and stator winding

insulation. Water and dirt buildup on the generator internal

windings will eventually decrease the insulation resistance of

these windings.

3.2 GENERATOR MAINTENANCE

SCHEDULE

Follow the recommended service schedule; to order replacement

parts call 1-888-436-3722.

Each

Use

Every 100

Hours

Every 6

Months

Each

Year

Fuel Level X

Oil Level X

Check Air Filter X

*Change Engine Oil X

**Clean Air Filter X

Check Spark Plug X

Check Muffler X

Replace Spark Plug X

Replace Fuel Filter X

* Perform initial oil change after the first five (5) hours of operation

** Clean the air filter more often if operating in dusty or sandy

conditions. Replace as necessary.

3.3 CLEANING THE GENERATOR

1. Use a damp cloth to wipe exterior surfaces clean.

2. A soft, bristle brush may be used to loosen caked on dirt, oil,

etc.

3. A vacuum cleaner may be used to pick up loose dirt and

debris.

4. Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and openings

on the generator. These openings must be kept clean and

unobstructed.

5. Inspect the vent hoses on the left side of the generator. Make

sure the hoses protrude through the slots below the door and

that the ends are open and free of debris.

3.4 ENGINE MAINTENANCE

NOTE:

Only work on a generator that has cooled completely.

n

Hot oil may cause burns. Allow engine to cool

entirely before draining oil. Avoid prolonged

or repeated skin exposure with used oil.

Thoroughly wash exposed areas with soap.

Inspect the oil level and air filter condition each time you are going

to use the generator. To check the air filter and oil level the left side

service cover must be removed; use a screwdriver to loosen the

screw securing the cover and remove.

The air filter is located behind a cover for the air box (Figure 10).

Push the tab on the bottom of the air box upwards to release the

cover. To service the air cleaner:

1. Remove the air cleaner. Tap the element to shake loose any

large particles.

2. Wash the element in soapy water. Squeeze the filter dry in

clean cloth (DO NOT TWIST).

Figure 10 - Air Filter

AIR

FILTER

HOUSING

COVER

LEFT SIDE

SERVICE COVER

SCREW

LEFT SIDE

SERVICE

COVER

Maintenance

3. Soak the filter element in clean engine oil. Squeeze the excess

oil from the filter, leaving a light coating.

4. Clean air cleaner housing and cover before re-installing the

filter element.

3.5 CHANGING THE ENGINE OIL

Change the engine oil after the first five (5) hours of operation.

Change the engine oil every 100 hours thereafter. To change the

engine oil:

1. Run the generator briefly to warm the engine oil; this also

loosens any engine deposits and makes the used oil flow

easier.

n

Change the oil only when the fuel tank is low

or nearly empty. Tipping the generator with a

full fuel tank may cause fuel leakage.

2. Place the generator over a drain pan and remove the drain

plug. Tip the generator on its side to drain the used oil from

the crankcase.

NOTE:

To make draining the oil easier, a 6” length of vinyl (PVC) hose

with an inside diameter of 1.25” (32mm) may be placed over

the drain lip.

3. Tip the generator upright once the oil has finished draining.

Replace the engine oil with the proper grade called out in

Section “ADDING ENGINE OIL”, then replace the drain plug.

3.6 CHANGING THE FUEL FILTER

Locate the fuel filter, just below the engine intake housing (Figure

11). Make sure the Fuel Shutoff is in the “OFF” (O) position.

1. Remove the pinch clamps securing the fuel filter. Pull the

hoses free.

Figure 11 - Fuel Filter

FUEL

FILTER

OIL FILL PLUG/

OIL DRAIN

CRANKCASE

VENT HOSE

CARBURETOR

VENT HOSE

n

Wipe up any fuel spills immediately! Do not

smoke or replace the fuel filter near sparks or

open flame!

2. Replace the used filter with a new one. Push the fuel hoses

onto the barbed filter fittings until they are seated completely.

3. Replace the clamps, making sure they are seated on the

fittings.

3.7 CHANGING THE SPARK PLUG

Replace the spark plug each year, regardless of how many hours

the generator has been run. Use a NGK CR7HSA that has been

gapped to .030” (.76mm). To replace the spark plug:

1. Remove the spark plug cover on the top right side of the

generator, just below the handle (Figure 12).

2. Carefully pull the spark plug lead from the spark plug. Use a

socket wrench to remove the spark plug.

3. Install the new spark plug into the cylinder head. Tighten the

spark plug to 15 ft/lb.

4. Replace the spark plug lead, making sure it is fully seated.

5. Replace the spark plug cover.

Figure 12 - Replace Spark Plug

SPARK PLUG

LOCATION

Maintenance

3.8 TRANSPORTATION AND STORAGE

Transport or store the generator only if it has cooled completely.

Make sure the fuel valve and the vent on the fuel cap are both in

the OFF (“O”) position.

It is important to prevent gum deposits from forming in essential

fuel system parts such as the carburetor, fuel hose or tank during

long-term storage. Also, experience indicates that alcohol-blended

fuels (called gasohol, ethanol or methanol) can attract moisture,

which leads to separation and formation of acids; these acids can

damage the fuel system of an engine while in storage.

To avoid engine problems, the use of a commercial fuel stabilizer

prior to storage is recommended. Follow the manufacturer’s

instructions when adding the fuel stabilizer.

If the generator is going to be stored for more than six (6) months,

the generator should be prepared as follows:

1. Remove all gasoline from the fuel tank.

2. Start and run engine until engine stops from lack of fuel or open

the valve on carburetor bowl (Figure 13), and allow gasoline

to drain down tube into a receptacle. Discard appropriately. Be

sure to close the valve once the gasoline has drained.

Figure 13 - Carburetor Drain Valve

CARBUREATOR DRAIN

VALVE LOCATED BEHIND

AIR INTAKE

TURN VALVE COUNTER-

CLOCKWISE TO DRAIN FUEL,

CLOCKWISE TO CLOSE

3. While engine is still warm, drain oil from crankcase. Refill with

recommended grade.

4. Remove spark plugs and pour about 1/2 ounce (15 ml) of

engine oil into the cylinders. Cover spark plug hole with rag.

Pull the starting rope several times to coat the cylinder walls

with engine oil.

5. Install and tighten the spark plug.

6. Clean the generator outer surfaces. Check that cooling air

slots and openings on generator are open and unobstructed.

7. Store the unit in a clean, dry place.

Do not store gasoline from one season to another.

If possible, store the unit indoors and cover it to give protection

from dust and dirt.

Maintenance

4.1 TROUBLESHOOTING GUIDE

PROBLEM CAUSE CORRECTIVE ACTION

Engine won't start. 1. No fuel in tank.

2. Fuel valve turned off.

3. Defective spark plug.

4. Plugged fuel filter.

5. Defective or stuck engine stop switch.

1. Add fuel to tank.

2. Turn fuel valve on.

3. Replace spark plug.

4. Replace fuel filter.

5. Replace engine start switch.

Engine starts, then shuts down. 1. Low fuel level.

2. Fuel tank vent closed.

3. Incorrect engine oil level.

4. Contaminated fuel.

5. Defective low oil level switch.

6. Defective ignition coil.

1. Add fuel to tank.

2. Open fuel tank vent.

3. Check engine oil level, add or drain as needed.

4. Replace fuel filter.

5. Replace Low Oil Level switch.

6. Replace ignition coil.

Engine starts, then runs rough. 1. Choke is stuck or left on.

2. Dirty or clogged air filter.

3. Defective or dirty spark plug.

4. Dirty fuel filter.

5. Defective FlexPower switch.

1. Turn choke off.

2. Clean or replace the air filter element.

3. Replace spark plug.

4. Replace fuel filter.

5. Replace FlexPower switch.

No AC output. 1. Generator is overloaded (OVERLOAD LED is on).

2. AC voltage is low (OVERLOAD LED is on).

3. Inverter module is overheated (OVERLOAD LED is

on).

4. Short circuit in load (OVERLOAD LED is on).

5. Defective inverter assembly.

1. Shut down generator to reset module. Reduce

loads and restart generator.

2. Verify vent is open and choke is OFF.

3. Verify service door is ON. Let cool for 15 minutes

and restart generator.

4. Verify condition of any extension cords and all

loads being powered.

5. Replace inverter assembly.

Fuel leaks from drain hoses. 1. Fuel system over primed (flooded).

2. Carburetor drain in bowl is not closed.

1. Turn vent in cap ON and let generator sit 15

minutes before restarting.

2. Turn valve clockwise to close.

* Engine speed increases and decreases — This is normal as the generator starts up and as loads vary.

Troubleshooting

Notes

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The United States Environmental Protection Agency (EPA) and Generac Power Systems, Inc. (Generac) are pleased to explain the

Emission Control System warranty on your new 2008 and later equipment. New equipment that use small spark-ignited engines

must be designed, built, and equipped to meet stringent anti-smog standards for the federal government. Generac will warrant

the emission control system on your generator for the period of time listed below provided there has been no abuse, neglect,

unapproved modification or improper maintenance of your equipment.

Your emission control system may include parts such as the: carburetor, ignition system, fuel system, catalytic converter, and other

associated emission-related components (if equipped).

MANUFACTURER’S WARRANTY COVERAGE:

This emission control system is warranted for two years. If, during such warranty period, any emission-related part on your

equipment is found to be defective in materials or workmanship, repairs or replacement will be performed by a Generac

Authorized Warranty Service Dealer.

OWNER'S WARRANTY RESPONSIBILITIES:

As the generator owner, you are responsible for the completion of all required maintenance as listed in your factory supplied

Owner's Manual. For warranty purposes, Generac recommends that you retain all receipts covering maintenance on your

generator, but Generac cannot deny warranty solely due to the lack of receipts.

As the generator owner, you should be aware that Generac may deny any and/or all warranty coverage or responsibility if your

generator, or a part/component thereof, has failed due to abuse, neglect, improper maintenance or unapproved modifications, or

the use of counterfeit and/or "grey market" parts not made, supplied or approved by Generac.

You are responsible for contacting a Generac Authorized Warranty Dealer as soon as a problem occurs. The warranty

repairs should be completed in a reasonable amount of time, not to exceed 30 days.

Warranty service can be arranged by contacting either your selling dealer or a Generac Authorized Warranty Service Dealer. To

locate the Generac Authorized Warranty Service Dealer nearest you, call our toll free number:

1-800-333-1322

IMPORTANT NOTE: This warranty statement explains your rights and obligations under the Emission Control System Warranty

(ECS Warranty), which is provided to you by Generac pursuant to federal law. See also the "Generac Limited Warranties for

Generac Power Systems, Inc.," which is enclosed herewith on a separate sheet, also provided to you by Generac. Note that this

warranty shall not apply to any incidental, consequential or indirect damages caused by defects in materials or workmanship or

any delay in repair or replacement of the defective part(s). This warranty is in place of all other warranties, expressed or implied.

Specifically, Generac makes no other warranties as to the merchantability or fitness for a particular purpose. Some states do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

The ECS Warranty applies only to the emission control system of your new equipment. If there is any conflict in terms between the

ECS Warranty and the Generac Warranty, the Generac Warranty shall apply. Both the ECS Warranty and the Generac Warranty

describe important rights and obligations with respect to your new engine.

Warranty service can be performed only by a Generac Authorized Warranty Service Facility. When requesting warranty service,

evidence must be presented showing the date of the sale to the original purchaser/owner.

If you have any questions regarding your warranty rights and responsibilities, you should contact Generac at the following

address:

ATTENTION WARRANTY DEPARTMENT

GENERAC POWER SYSTEMS, INC.

P.O. BOX 297 • WHITEWATER, WI 53190

Part 1

Part No. 0H1911 Rev. A 01/09

Warranty

EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (ECS warranty) for equipment using small spark-ignited engines:

(a) Applicability: This warranty shall apply to equipment that uses small off-road engines. The ECS Warranty period shall begin

on the date the new equipment is purchased by/delivered to its original, end-use purchaser/owner and shall continue for 24

consecutive months thereafter.

(b) General Emissions Warranty Coverage: Generac warrants to the original, end-use purchaser/owner of the new engine or

equipment and to each subsequent purchaser/owner that the ECS when installed was:

(1) Designed, built and equipped so as to conform with all applicable regulations; and

(2) Free from defects in materials and workmanship which cause the failure of a warranted part at any time during the ECS

Warranty Period.

(1) Any warranted part that is not scheduled for replacement as required maintenance in the Owner's Manual shall be

warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or

replaced by Generac according to Subsection (4) below. Any such part repaired or replaced under the ECS Warranty shall

be warranted for the remainder of the ECS Warranty Period.

(2) Any warranted part that is scheduled only for regular inspection as specified in the Owner's Manual shall be warranted

for the ECS Warranty Period. A statement in the Owner’s Manual to the effect of "repair or replace as necessary" shall not

reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the

remainder of the ECS Warranty Period.

(3) Any warranted part that is scheduled for replacement as required maintenance in the Owner's Manual shall be warranted

for the period of time prior to first scheduled replacement point for that part. If the part fails prior to the first scheduled

replacement, the part shall be repaired or replaced by Generac according to Subsection (4) below. Any such emissions-

related part repaired or replaced under the ECS warranty shall be warranted for the remainder of the period prior to the

first scheduled replacement point for that part.

(4) Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be performed at no charge

to the owner at a Generac Authorized Warranty Service Facility.

(5) Notwithstanding the provisions of subsection (4) above, warranty services or repairs must be provided at Generac

Authorized Service Facilities.

(6) When the engine is inspected by a Generac Authorized Warranty Service Facility, the purchaser/owner shall not be held

responsible for diagnostic costs if the repair is deemed warrantable.

(7) Throughout the ECS Warranty Period, Generac shall maintain a supply of warranted emission-related parts sufficient to

meet the expected demand for such parts.

(8) Any Generac authorized and approved emission-related replacement parts may be used in the performance of any ECS

warranty maintenance or repairs and will be provided without charge to the purchaser/owner. Such use shall not reduce

Generac ECS Warranty obligations.

(9) Unapproved, add-on, modified, counterfeit and/or "grey market" parts may not be used to modify or repair a Generac

engine. Such use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. Generac

shall not be held liable hereunder for failures of any warranted parts of Generac equipment caused by the use of such an

unapproved, add-on, modified, counterfeit and/or "grey market" part.

EMISSION RELATED PARTS MAY INCLUDE THE FOLLOWING (IF EQUIPPED):

1) FUEL METERING SYSTEM

A. CARBURETOR AND INTERNAL PARTS

B. PRESSURE REGULATOR

2) AIR INDUCTION SYSTEM

A. INTAKE MANIFOLD

B. AIR FILTER

3) IGNITION SYSTEM

A. SPARK PLUGS

B. IGNITION COILS / MODULE

4) AIR INJECTION SYSTEM

A. PULSE AIR VALVE

5) EXHAUST SYSTEM

A. CATALYST

B. THERMAL REACTOR

C. EXHAUST MANIFOLD

Part 2

Part No. 0H1911 Rev. A 01/09

Warranty

Manual Part No. 0H8108 Rev. B (09/14/10) Printed in China

Warranty

GENERAC POWER SYSTEMS “TWO YEAR” LIMITED WARRANTY FOR

iX SERIES PORTABLE GENERATORS

For a period of two years from the date of original sale, Generac Power Systems, Inc. (Generac) warrants its iX Series generators will be free from defects in materials and

workmanship for the items and period set forth below. Generac will, at its option, repair or replace any part which, upon examination, inspection and testing by Generac or a

Generac Authorized Warranty Service Dealer, is found to be defective. Any equipment that the purchaser/owner claims to be defective must be returned to and examined by the

nearest Generac Authorized Warranty Service Dealer. All transportation costs under the warranty, including return to the factory, are to be borne and prepaid by the purchaser/

owner. This warranty applies only to Generac iX Series portable generators and is not transferable from original purchaser. Save your proof-of-purchase receipt. If you do not

provide proof of the initial purchase date, the manufacturer’s shipping date of the product will be used to determine the warranty period.

** This warranty only applies to units sold for use in the U.S.A. and Canada.**

WARRANTY SCHEDULE

Consumer applications are warranted for two (2) years. Commercial and Rental applications are warranted for six (6) months.

CONSUMER APPLICATION

YEAR ONE - Limited Comprehensive coverage on Labor and Part(s) listed (proof of purchase and maintenance is required):

• Engine- All Components

• Alternator- All Components

YEAR TWO - Limited Comprehensive coverage on Part(s) listed (proof of purchase and maintenance is required):

• Engine- All Components

• Alternator- All Components

COMMERCIAL/RENTAL APPLICATION

FIRST SIX MONTHS – Limited Comprehensive coverage on Labor and Part(s) listed (proof of purchase and maintenance is required):

• Engine- All Components

• Alternator- All Components

NOTE: For the purpose of this warranty “consumer use” means personal residential household or recreational use by original purchaser. This warranty does not apply to

units used for Prime Power in place of utility where utility power service is present or where utility power service does not normally exist. Once a generator has

experienced commercial or rental use, it shall thereafter be considered a non-consumer use generator for the purpose of this warranty.

All warranty expense allowances are subject to the conditions defined in Generac’s Service Policy Manual.

THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING:

Generac portable generators that utilize non-Generac replacement parts.•

Costs of normal maintenance and adjustments.•

Failures caused by any contaminated fuels, oils or lack of proper oil levels.•

Repairs or diagnostics performed by individuals other than Guardian/Generac authorized dealers not authorized in writing by Generac Power Systems.•

Failures due, but not limited, to normal wear and tear, accident, misuse, abuse, negligence or improper use. As with all mechanical devices, the Generac engines need periodic •

part(s) service and replacement to perform as designed. This warranty will not cover repair when normal use has exhausted the life of a part(s) or engine.

Failures caused by any act of God and other force majeure events beyond the manufactures control.•

Damage related to rodent and/or insect infestation.•

Products that are modified or altered in a manner not authorized by Generac in writing.•

Any incidental, consequential or indirect damages caused by defects in materials or workmanship, or any delay in repair or replacement of the defective part(s).•

Failure due to misapplication.•

Telephone, cellular phone, facsimile, internet access or other communication expenses.•

Living or travel expenses of person(s) performing service, except as specifically included within the terms of a specific unit warranty period.•

Expenses related to “customer instruction” or troubleshooting where no manufacturing defect is found.•

Rental equipment used while warranty repairs are being performed.•

Overnight freight or special shipping costs for replacement part(s).•

Overtime, holiday or emergency labor.•

Starting batteries, fuses, light bulbs and engine fluids.•

THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, SPECIFICALLY, GENERAC POWER SYSTEMS MAKES NO OTHER WARRANTIES AS TO

THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Any implied warranties which are allowed by law, shall be limited in duration to the terms of the express

warranty provided herein. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to purchaser/owner.

GENERAC POWER SYSTEMS ONLY LIABILITY SHALL BE THE REPAIR OR REPLACEMENT OF PART(S) AS STATED ABOVE. IN NO EVENT SHALL GENERAC POWER SYSTEMS

BE LIABLE FOR ANY INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF GENERAC POWER SYSTEMS, INC. NEGLIGENCE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to purchaser/owner. Purchaser/owner

agrees to make no claims against Generac Power Systems, Inc. based on negligence. This warranty gives purchaser/owner specific legal rights. Purchaser/owner also may

have other rights that vary from state to state.

GENERAC POWER SYSTEMS, INC.

P.O. BOX 8 • Waukesha, WI 53187

Ph: (888) GENERAC (436-3722) • Fax: (262) 544-4851

To locate the nearest Authorized Dealer visit our website www.generac.com

Part No. 0H4535 Revision D (09/14/10) Printed in China

www.generac.com or 1-888-GENERAC

iX 800

Manual del operador del Generador

Inversor Digital

MODELO: 005791-2

Caja de accesorios ................................................................18

Introducción ...........................................................................19

Lea este manual completamente ...........................................19

Reglas de seguridad ..............................................................19

Índice de estándares ......................................................21

Información General ..............................................................22

1.1 Especificaciones ............................................................22

1.1.1 Información sobre las emisiones .........................22

1.2 Identificación de la unidad ..............................................22

1.2.1 Tablero de control ...............................................23

Operación ..............................................................................23

2.1 Revisión antes de usar ...................................................23

2.2 Arranque del generador ..................................................24

2.3 Agregar cargas...............................................................24

2.4 Uso del interruptor FlexPower

™

...................................... 25

2.5 Apagado ........................................................................25

2.6 Apagado por bajo nivel de aceite ....................................26

2.7 Echando combustible al generador .................................26

2.7.1 Para llenar el tanque de combustible ...................26

2.8 Agregando aceite de motor ............................................26

2.8.1 Para agregar aceite de motor al cárter .................26

Mantenimiento .......................................................................27

3.1 Mantenimiento del generador .........................................27

3.2 Programa de mantenimiento del generador .....................27

3.3 Limpiando el generador ..................................................27

3.4 Mantenimiento del motor ................................................28

3.5 Cambio de aceite de motor ............................................28

3.6 Cambio del filtro de combustible ....................................28

3.7 Cambio de bujía .............................................................29

3.8 Transporte y almacenamiento .........................................29

Detección de problemas ........................................................30

4.1 Guía de detección de problemas ....................................30

Notas .....................................................................................31

Garantía .................................................................................32

CAJA DE ACCESORIOS

Revise todo el contenido. Si alguna parte no se encuentra o está

dañada, ubique a un concesionario autorizado en el telf. 1-888-

436-3722.

El contenido incluye:

1 botella de aceite SAE 30 • • Chimenea de aceite

Llave de bujías • Destornillador•

Cable de carga de la batería•

Tabla de contenidos

La page charge ...

Generac iX800 0057912 Manuel utilisateur

Marque: Generac

Modèle: iX800 0057912

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac iX800 0057912 User manual
español: Generac iX800 0057912 Manual de usuario

Generac iX800 0057912 Manuel utilisateur

Generac iX800 0057912 Manuel utilisateur

dans d''autres langues

Documents connexes