Schumacher BRP 715005061 Automatic Battery Charger Le manuel du propriétaire
- Catégorie
- Chargeurs de batterie de voiture
- Taper
- Le manuel du propriétaire
MODEL / MODÈLE:
715005061
Automatic Battery Charger
Chargeur de batterie automatique
OWNER’S MANUAL /MANUEL D’UTILISATION
NOTICE
This product is for usage ON the vehicle for: Can-Am off-road, Can-Am Spyder
and Ski-Doo only. For Sea-Doo, this product must be used outside of the vehicle.
Ce produit est pour une utilisation SUR le véhicule pour : Can-Am hors-route,
Spyder et Ski-Doo seulement. Ce produit doit être utilisé à l’extérieur du véhicule
pour un Sea-Doo ou autre embarcation nautique.
PLEASE SAVE THIS OWNER’S MANUAL AND READ BEFORE EACH USE.
This manual will explain how to use the charger safely and effectively. Please
read and follow these instructions and precautions carefully.
VEUILLEZ CONSERVER LE MANUEL D’INSTRUCTIONS ET LE LIRE AVANT
CHAQUE UTILISATION. Ce manuel explique comment utiliser l’unité d’une façon
sûre et efficace. Veuillez lire et suivre attentivement ces instructions et précautions.
0099001920-03
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .................................................................................4
PERSONAL SAFETY PRECAUTIONS ...................................................................................5
PREPARING TO CHARGE ......................................................................................................5
CHARGER LOCATION ............................................................................................................6
DC CONNECTION PRECAUTIONS .......................................................................................6
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE ...........................6
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE ...................................7
GROUNDING AND AC POWER CORD CONNECTIONS .....................................................7
ASSEMBLY INSTRUCTIONS ..................................................................................................8
FEATURES ...............................................................................................................................8
CONTROL PANEL ...................................................................................................................8
OPERATING INSTRUCTIONS ................................................................................................9
DISPLAY MESSAGES .......................................................................................................... 12
MAINTENANCE AND CARE ................................................................................................ 13
TROUBLESHOOTING .......................................................................................................... 13
SPECIFICATIONS ................................................................................................................. 14
REPLACEMENT PARTS....................................................................................................... 15
BEFORE RETURNING ......................................................................................................... 15
LIMITED WARRANTY ........................................................................................................... 15
WARRANTY CARD............................................................................................................... 33
TABLE DES MATIÈRES
CONSIGNES DE SÉCURITÉ IMPORTANTES ................................................................... 17
MESURES DE SÉCURITÉ PERSONNELLE ...................................................................... 18
PRÉPARATION POUR LA CHARGE ................................................................................... 19
EMPLACEMENT DU CHARGEUR ...................................................................................... 19
PRÉCAUTIONS SUR LA CONNEXION C.C. ...................................................................... 19
ÉTAPES À SUIVRE LORSQUE LA BATTERIE EST INSTALLÉE DANS UN VÉHICULE . 20
ÉTAPES À SUIVRE LORSQUE LA BATTERIE EST INSTALLÉE HORS DU VÉHICULE 20
MISE À LA TERRE ET CORDON D’ALIMENTATION CA................................................... 21
DIRECTIVES D’ASSEMBLAGE ........................................................................................... 21
CARACTÉRISTIQUES ......................................................................................................... 22
PANNEAU DE CONTRÔLE.................................................................................................. 22
CONSIGNES D’UTILISATION ..............................................................................................23
AFFICHAGE DES MESSAGES ........................................................................................... 27
SOINS ET ENTRETIEN ........................................................................................................ 28
TABLEAU DE DÉPANNAGE ................................................................................................29
CARACTÉRISTIQUES ......................................................................................................... 30
PIÈCES DE RECHANGE ..................................................................................................... 30
AVANT DE RETOURNER ..................................................................................................... 30
GARANTIE LIMITÉE ............................................................................................................. 31
CARTE DE GARANTIE......................................................................................................... 34
• 4 •
487802781
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
1.1 SAVE THESE INSTRUCTIONS – This manual contains important safety and
operating instructions.
1.2 This charger is not intended for use by children.
1.3 Do not expose the charger to rain or snow.
1.4 Use of an attachment not recommended or sold by the battery charger
manufacturer may result in a risk of fire, electric shock or injury to persons.
1.5 To reduce the risk of damage to electric plug and cord, pull by the plug rather
than the cord when disconnecting charger.
1.6 An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If an
extension cord must be used, make sure:
• That the pins on plug of extension cord are the same number, size and shape
as those of plug on charger.
• That extension cord is properly wired and in good electrical condition; and
• That wire size is large enough for AC ampere rating of charger, as specified in
section 8.
1.7 Do not operate charger with damaged cord or plug – replace the cord or plug
immediately.
1.8 Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it to a qualified serviceman.
1.9 Do not disassemble charger; take it to a qualified serviceman when service or repair
is required. Incorrect reassembly may result in a risk of electric shock or fire.
1.10 To reduce risk of electric shock, unplug charger from outlet before attempting any
maintenance or cleaning. Turning off controls will not reduce this risk.
1.11 WARNING: RISK OF EXPLOSIVE GASES.
a.
WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY
OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT
YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER.
b.
To reduce risk of battery explosion, follow these instructions and those
published by battery manufacturer and manufacturer of any equipment you
intend to use in vicinity of battery. Review cautionary markings on these
products and on the engine.
• 5 •
487802781
2. PERSONAL SAFETY PRECAUTIONS
2.1 Consider having someone close enough by to come to your aid when you work
near a lead-acid battery.
2.2 Have plenty of fresh water and soap nearby in case battery acid contacts skin,
clothing, or eyes.
2.3 Wear complete eye protection and clothing protection. Avoid touching eyes while
working near battery.
2.4 If battery acid contacts skin or clothing, wash immediately with soap and water.
If acid enters eye, immediately flood eye with running cold water for at least 10
minutes and get medical attention immediately.
2.5 NEVER smoke or allow a spark or flame in vicinity of battery or engine.
2.6 Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark
or short-circuit battery or other electrical part that may cause explosion.
2.7 Remove personal metal items such as rings, bracelets, necklaces, and watches
when working with a lead-acid battery. A lead-acid battery can produce a short-
circuit current high enough to weld a ring or the like to metal, causing a severe burn.
2.8 Use the charger for charging only 6 and 12V LEAD-ACID, GEL and AGM-type
rechargeable batteries with recommended rated capacities of 12Ah (6V) and 12-59Ah
(12V). It is not intended to supply power to a low voltage electrical system other
than in a starter-motor application. Do not use battery charger for charging dry-
cell batteries that are commonly used with home appliances. These batteries may
burst and cause injury to persons and damage to property.
2.9 NEVER charge a frozen battery.
2.10 WARNING: This product contains one or more chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
3. PREPARING TO CHARGE
3.1
If necessary to remove battery from vehicle to charge, always remove grounded
terminal from battery first. Make sure all accessories in the vehicle are off, so as
not to cause an arc.
3.2
Be sure area around battery is well ventilated while battery is being charged.
3.3
Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.
3.4
Add distilled water in each cell until battery acid reaches level specified by battery
manufacturer. Do not overfill. For a battery without removable cell caps, such as valve
regulated lead acid batteries, carefully follow manufacturer’s recharging instructions.
3.5
Study all battery manufacturer’s specific precautions while charging and
recommended rates of charge.
• 6 •
487802781
3.6
Determine voltage of battery by referring to car owner’s manual and make
sure that output voltage selector switch is set at correct voltage. If charger has
adjustable charge rate, charge battery initially at lowest rate.
4. CHARGER LOCATION
4.1
Locate charger as far away from battery as DC cables permit.
4.2
Never place charger directly above battery being charged; gases from battery will
corrode and damage charger.
4.3
Never allow battery acid to drip on charger when reading electrolyte specific
gravity or filling battery.
4.4
Do not operate charger in a closed-in area or restrict ventilation in any way.
4.5
Do not set a battery on top of charger.
5. DC CONNECTION PRECAUTIONS
5.1 Connect and disconnect DC output clips only after setting any charger switches
to “off” position and removing AC cord from electric outlet. Never allow clips to
touch each other.
5.2 Attach clips to battery and chassis, as indicated in the sections 6 and 7.
6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE
NOTE: A marine (boat/PWC) battery must be removed and charged on shore.
To charge it on board requires equipment specially designed for marine use.
WARNING: A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:
6.1
Position AC and DC cords to reduce risk of damage by hood, door, or moving
engine part.
6.2
Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.
6.3
Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has
larger diameter than NEGATIVE (NEG, N,–) post.
6.4
Determine which post of battery is grounded (connected) to the chassis. If
negative post is grounded to chassis (as in most vehicles), see (6.5). If positive
post is grounded to the chassis, see (6.6).
6.5
For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger
to POSITIVE (POS, P, +) ungrounded post of battery. Connect NEGATIVE (BLACK)
clip to vehicle chassis or engine block away from battery. Do not connect clip to
carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal
part of the frame or engine block.
6.6
For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery
• 7 •
487802781
charger to NEGATIVE (NEG, N, –) ungrounded post of battery. Connect POSITIVE
(RED) clip to vehicle chassis or engine block away from battery. Do not connect clip
to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge
metal part of the frame or engine block.
6.7
When disconnecting charger, turn switches to off, disconnect AC cord, remove clip
from vehicle chassis, and then remove clip from battery terminal.
6.8
See Operating Instructions for length of charge information.
7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE
WARNING: A SPARK NEAR THE BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:
7.1
Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a
larger diameter than NEGATIVE (NEG, N, –) post.
7.2
Attach at least a 24-inch-long 6-gauge (AWG) insulated battery cable to
NEGATIVE (NEG, N, –) battery post.
7.3
Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery.
7.4
Position yourself and free end of cable as far away from battery as possible –
then connect NEGATIVE (BLACK) charger clip to free end of cable.
7.5
Do not face battery when making final connection.
7.6
When disconnecting charger, always do so in reverse sequence of connecting
procedure and break first connection while as far away from battery as practical.
8. GROUNDING AND AC POWER CORD CONNECTIONS
8.1
This battery charger is for use on a nominal 120 volt circuit. The plug must be
plugged into an outlet that is properly installed and grounded in accordance with
all local codes and ordinances. The plug pins must fit the receptacle (outlet). Do
not use with an ungrounded system.
8.2
DANGER: Never alter the AC cord or plug provided – if it does not fit the outlet,
have a proper grounded outlet installed by a qualified electrician. An improper
connection can result in a risk of an electric shock or electrocution.
NOTE: Pursuant to Canadian Regulations, use of an adapter plug is not allowed
in Canada. Use of an adapter plug in the United States is not recommended and
should not be used.
8.3
USING AN EXTENSION CORD
The use of an extension cord is not recommended. If you must use an extension
cord, follow these guidelines:
• Pins on plug of extension cord must be the same number, size, and shape as
those of plug on charger.
• 8 •
487802781
• Ensure that the extension cord is properly wired and in good electrical condition.
• Wire size must be large enough for the AC ampere rating of charger, as specified below:
Length of cord (feet)
25
50
100
150
AWG* size of cord
18
18
16
14
*AWG-American Wire Gauge
9. ASSEMBLY INSTRUCTIONS
9.1 Remove all cord wraps and uncoil the cables prior to using the battery charger.
10. FEATURES
2
3
4
5
1. AC Power cord
2. Digital display
3. Display/ON button
4. Charging/Charged/Maintaining
LED indicator
5. Hook attachment
6. 12V accessory plug
quick-connect
7. Battery clamp quick-connect
8. Ring terminal quick-connect
11. CONTROL PANEL
DIGITAL DISPLAY
The digital display indicates the status of the battery and charger. See the Display
Messages section for a complete list of messages.
NOTE: During charging, the display will go into sleep mode and will not display any
messages. To turn the display back on, press the display button.
DISPLAY/ON BUTTON
The digital display will show the battery’s voltage and percentage of charge.
Press the display button to show the charge progress.
LED DISPLAY
GREEN LED solid (CHARGING): The charger is charging the battery.
GREEN LED pulsing (CHARGED/MAINTAINING): The battery is fully charged
and the charger is in maintain mode.
GREEN LED flashing: The charge has aborted (see Aborted Charge section).
• 9 •
487802781
12. OPERATING INSTRUCTIONS
IMPORTANT: Do not start the vehicle with the charger connected to the AC
outlet, or it may damage the charger and your vehicle.
NOTE: This charger is equipped with an auto-start feature. Current will not be
supplied to the battery clamps until a battery is properly connected. The clamps
will not spark if touched together.
NOTE:
A marine (boat/PWC) battery must be removed and charged on shore.
CHARGING A BATTERY IN THE VEHICLE
1. Turn off all the vehicle’s accessories.
2. Keep the hood open.
3. Clean the battery terminals.
4. Place the charger on a dry, non-flammable surface, or use the convenient hook
attachment to hang the unit safely outside the work area.
5. Lay the AC/DC cables away from any fan blades, belts, pulleys and other
moving parts.
6. Connect the battery, following the precautions listed in sections 6 and 7.
7. Connect the charger to an electrical outlet.
8. When the charger starts, the GREEN LED will be solid, and the display will show
ANALYZING BATTERY while the charger determines that the battery is properly
connected, the condition of the battery, and whether the battery is 6V or 12V.
9. Monitor the progress of the charge by pressing the display button on the front
of the unit. When the battery is fully charged, the GREEN LED will pulse.
10. When charging is complete, disconnect the charger from the AC power,
remove the clamps from the vehicle’s chassis, and then remove the clamp
from the battery terminal.
CHARGING A BATTERY OUTSIDE OF THE VEHICLE
1. Place battery in a well-ventilated area.
2. Clean the battery terminals.
3. Connect the battery, following the precautions listed in sections 6 and 7.
4. Connect the charger to the electrical outlet.
5. When the charger starts, the GREEN LED will be solid, and the display will show
ANALYZING BATTERY while the charger determines if the battery is properly
connected, the condition of the battery, and whether the battery is 6V or 12V.
6. Monitor the progress of the charge by pressing the display button on
the front of the unit. When the battery is fully charged, the GREEN LED will pulse.
7. When charging is complete, disconnect the charger from the AC power,
disconnect the negative clamp, and finally the positive clamp.
• 10 •
487802781
USING THE QUICK-CONNECT CABLE CONNECTORS
Connect any of the three output cable assemblies to the charger in a matter
of seconds.
IMPORTANT: Never connect the clamp and ring terminal connectors together
for use in other applications, such as external battery or other power source
charging, or to extend the output cable length, as reverse polarity and/or
overcharge conditions will occur.
BATTERY CLAMP QUICK-CONNECT
1. Connect the end of the charger output cable to the end of the battery clamp
quick-connect.
2. Follow the steps in previous sections to connect the output clamps to the battery.
3. After a good electrical connection is made to the battery, plug the power cord
into a grounded 120V AC electrical wall outlet.
RING TERMINAL QUICK-CONNECT
The ring connectors permanently attach to the battery, providing easy access
to quickly connect the charger to your battery. This application is appropriate for
motorcycles, lawn tractors, ATVs and snowmobiles.
1.
To permanently attach to a battery, loosen and remove each nut from the bolt
at the battery terminal.
2.
Connect the red POSITIVE connector ring to the POSITIVE battery terminal.
3.
Connect the black NEGATIVE connector ring to the NEGATIVE battery terminal.
4.
Replace and tighten the nuts to secure.
5.
Connect the cable to the end of the charger output cord.
Take care to keep the wires and plug away from metal and moving parts.
6.
Plug the charger power cord into a grounded 120V AC electrical wall outlet.
12V ACCESSORY PLUG QUICK-CONNECT
Charge or maintain your battery without lifting the hood.
1.
Connect the end of the 12V accessory plug quick-connect to the charger.
2.
Insert the 12V accessory plug into the 12V accessory outlet.
3.
Route the power cord from the charger through the vehicle’s open window.
4.
Plug the charger power cord into a grounded 120V AC electrical wall outlet.
5.
If the vehicle’s ignition key has to be on in order for the accessory outlet to
supply/receive power, turn the key, without starting the engine.
• 11 •
487802781
BATTERY CHARGING TIMES
CCA = Cold Cranking Amps RC = Reserve Capacity
Ah = Amp Hour NR = Not Recommended
BATTERY SIZE/RATING
CHARGE TIME (3A)
SMALL BATTERIES
Motorcycle, garden tractor, etc.
6-12 Ah
1½-2½ h
12-32 Ah
2½-7 h
CARS AND TRUCKS
200-315 CCA
40-60 RC
7½-9½ h
315-550 CCA
60-85 RC
MAINTAIN ONLY
550-1000 CCA
85-190 RC
MAINTAIN ONLY
MARINE/DEEP-CYCLE
80 RC
MAINTAIN ONLY
140 RC
MAINTAIN ONLY
160 RC
MAINTAIN ONLY
180 RC
MAINTAIN ONLY
Times are based on a 50% discharged battery and may change, depending on age and condition of battery.
AUTOMATIC CHARGING MODE
When an automatic charge is performed, the charger switches to the maintain
mode automatically after the battery is charged.
BATTERY CONNECTION INDICATOR
If the charger does not detect a properly connected battery, charging will not
start and the digital display will show one of two messages. If the display shows
CONNECT CLAMPS, make sure the charger is connected to the battery and the
connection points are clean and making a good connection. If the display shows
WARNING CLAMPS REVERSED, unplug the charger from the AC outlet, reverse
the connections at the battery, and then plug the charger back in.
CHARGE COMPLETION AND MAINTAIN MODE
(FLOAT MODE MONITORING)
Charge completion is indicated by the GREEN LED pulsing and the digital
display showing FULLY CHARGED AUTO MAINTAINING. This means that
the charger has stopped charging and has switched to the Maintain Mode of
operation. NOTE: If the charger has to provide its maximum maintain current
for a continuous 12 hour period, it will go into Abort Mode (see Aborted Charge
section). This is usually caused by a drain on the battery, or the battery could be
bad. Make sure there are no loads on the battery. If there are, remove them. If
there are none, have the battery checked or replaced.
• 12 •
487802781
MAINTAINING A BATTERY
The 715005061 maintains both 6 and 12 volt batteries, keeping them at full charge.
It can charge small batteries and maintain both small and large batteries. If you are
maintaining a fully charged large battery, you are properly utilizing the battery charger.
However, if you use this battery charger to charge a large battery, such as a marine
deep-cycle battery that was not fully charged, you may not get the battery’s full capacity.
Therefore, we do not recommend charging a large battery with this unit.
NOTE: The maintain mode technology allows you to safely charge and maintain a
healthy battery for extended periods of time. However, problems with the battery,
electrical problems in the vehicle, improper connections or other unanticipated
conditions could cause excessive current draws. As such, occasionally monitoring
your battery and the charging process is required.
DESULFATION MODE
If the battery is left discharged for an extended period of time, it could become sulfated
and not accept a normal charge. If the charger detects a sulfated battery, the charger
will switch to a special mode of operation designed for such batteries. If successful,
normal charging will resume after the battery is desulfated. Desulfation could take up
to 8 hours. If desulfation fails, charging will abort, the GREEN LED will flash, and the
display will show CHARGE ABORTED-BAD BATTERY.
ABORTED CHARGE
If charging cannot be completed normally, charging will abort. When charging aborts,
the charger’s output is shut off, the GREEN LED will flash, and the display will show
CHARGE ABORTED-BAD BATTERY. To reset after an aborted charge, unplug the
charger from the outlet, wait a few moments and plug it back in.
13. DISPLAY MESSAGES
CONNECT CLAMPS (No LED lit) – Plugged into the AC outlet without the clamps
connected to a battery.
WARNING CLAMPS REVERSED (No LED lit) – Plugged into the AC outlet and
the clamps are connected backwards to a 6V or 12V battery.
ANALYZING BATTERY (Green LED lit) – Plugged into the AC outlet, and when
first connected to a 6V or 12V battery correctly.
CHARGING 12V – XX% (Green LED lit) – Plugged into the AC outlet and
correctly connected to a discharged 12V battery.
CHARGING 6V – XX% (Green LED lit) – Plugged into the AC outlet and correctly
connected to a discharged 6V battery.
FULLY CHARGED AUTO MAINTAINING (Green LED pulsing) – Plugged into the AC
outlet and correctly connected to a fully charged 6V or 12V battery.
• 13 •
487802781
CHARGE ABORTED-BAD BATTERY (Green LED flashing) –
Circumstances that could cause an Abort situation during charging:
• The battery is severely sulfated or has a shorted cell and can’t reach a full charge.
• The battery is too large or there is a bank of batteries and it doesn’t reach full
charge within a set time period.
Circumstances that could cause an Abort situation during maintain:
• The battery is severely sulfated or has a weak cell and will not hold a charge.
• There is a large draw on the battery and the charger has to supply its maximum
maintain current for a 12 hour period to keep the battery at full charge.
14. MAINTENANCE AND CARE
A minimal amount of care can keep your battery charger working properly for years.
• Clean the clamps each time you are finished charging. Wipe off any battery fluid
that may have come in contact with the clamps, to prevent corrosion.
• Occasionally cleaning the case of the charger with a soft cloth will keep the finish
shiny and help prevent corrosion.
• Coil the input and output cords neatly when storing the charger. This will help
prevent accidental damage to the cords and charger.
• Store the charger unplugged from the AC power outlet in an upright position.
• Store inside, in a cool, dry place. Do not store the clamps clipped together, on or
around metal, or clipped to the cables.
15. TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
REASON/SOLUTION
Battery clamps do not
spark when touched
together.
The charger is equipped
with an auto-start feature. It
will not supply current to the
battery clamps until a battery
is properly connected. The
clamps will not spark if
touched together.
No problem; this is a normal
condition.
The charger will not
turn on when properly
connected.
AC outlet is dead.
Poor electrical connection.
Check for open fuse or circuit
breaker supplying AC outlet.
Check power cord and
extension cord for loose
fitting plug.
• 14 •
487802781
PROBLEM
POSSIBLE CAUSE
REASON/SOLUTION
I cannot select a 6V
or 12V setting.
The charger is equipped
with Auto Voltage Detection,
which automatically detects
the voltage and charges the
battery.
No problem; this is normal.
Green LED is solid
and the display
shows ANALYZING
BATTERY.
The charger needs to check
the condition of the battery.
The Green LED will be solid
when the charger is checking
the condition of the battery.
This is normal.
Green LED is flashing
and the display shows
CHARGE ABORTED-
BAD BATTERY.
The battery is sulfated.
The battery is too large for
the charger.
Reset the charger by briefly
unplugging it.
You need a charger with a
higher amp rate.
The display shows
CONNECT CLAMPS.
The clamps are not making a
good connection.
The fuse is bad.
Check for poor connection at
battery and frame.
Replace the in-line fuse for
the ring connector.
16. SPECIFICATIONS
Input Voltage ................................................................120V AC @ 60Hz, 0.91A
Output Voltage .......................................6V or 12V, with Auto Voltage Detection
Output Current Rating ..........................................................2A @ 6V; 3A @12V
• 15 •
487802781
17. REPLACEMENT PARTS
Battery clamps (quick-connect)..................................................... 3899002636Z
Ring connectors (quick-connect) .................................................. 2299002042Z
12V accessory plug (quick-connect) ............................................. 3899001401Z
18. BEFORE RETURNING
For information about troubleshooting,
contact customer service for assistance:
services@schumacherelectric.com
www.batterychargers.com
or call 1-800-621-5485, Monday-Friday
7:00am to 5:00pm CST
19. LIMITED WARRANTY
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO
THE ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED
WARRANTY IS NOT TRANSFERABLE OR ASSIGNABLE.
Schumacher Electric Corporation (the “Manufacturer”) warrants this charger for
five (5) years from the date of purchase at retail against defective material or
workmanship that may occur under normal use and care. If your unit is not free from
defective material or workmanship, Manufacturer’s obligation under this warranty is
solely to repair or replace your product with a new or reconditioned unit at the option
of the Manufacturer. It is the obligation of the purchaser to forward the unit, along
with proof of purchase and mailing charges prepaid to the retailer from which it was
purchased for free replacement.
• 16 •
487802781
Manufacturer does not provide any warranty for any accessories used with this
product that are not manufactured by Schumacher Electric Corporation and
approved for use with this product. This Limited Warranty is void if the product is
misused, subjected to careless handling, repaired, or modified by anyone other
than Manufacturer or if this unit is resold through an unauthorized retailer.
Manufacturer may void this Limited Warranty if a “warranty void if removed” label
is removed from the product.
Manufacturer makes no other warranties, including, but not limited to, express, implied
or statutory warranties, including without limitation, any implied warranty of
merchantability or implied warranty of fitness for a particular purpose. Further,
Manufacturer shall not be liable for any incidental, special or consequential damage
claims incurred by purchasers, users or others associated with this product, including,
but not limited to, lost profits, revenues, anticipated sales, business opportunities,
goodwill, business interruption and any other injury or damage. Any and all such
warranties, other than the limited warranty included herein, are hereby expressly
disclaimed and excluded. Some states do not allow the exclusion or limitation of
incidental or consequential damages or length of implied warranty, so the above
limitations or exclusions may not apply to you. This warranty gives you specific legal
rights and it is possible you may have other rights which vary from this warranty.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND
THE MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO
ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT
OTHER THAN THIS WARRANTY.
Schumacher
®
and the Schumacher logo are registered
trademarks of Schumacher Electric Corporation.
Bombardier Recreational Products Inc.
726 St. Joseph, Valcourt (QC), Canada JOE 2L0
www.brp.com
• 17 •
487802781
1. CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS.
1.1 CONSERVER CES INSTRUCTIONS – Ce manuel contient des instructions
importantes concernant la sécurité et le fonctionnement.
1.2 Ne pas laisser à la portée des enfants.
1.3 Ne pas exposer le chargeur à la pluie ou la neige.
1.4 N’utilisez que les accessoires recommandés. L’utilisation d’accessoires non
recommandés ou vendus par le fabricant du chargeur de batterie peut engendrer
un risque d’incendie, un choc électrique ou des blessures.
1.5 Pour réduire le risque d’endommager le cordon électrique, tirez sur la prise plutôt
que sur le cordon quand vous débranchez le chargeur.
1.6 Une rallonge ne devrait pas être utilisée sauf en cas de nécessité absolue.
L’utilisation d’une rallonge inadéquate peut causer un risque de feu ou de choc
électrique. Si vous devez utiliser une rallonge assurez-vous que :
• Les broches sur la prise de la rallonge sont du même nombre, de la même
taille et forme que celles de la prise du chargeur.
• La rallonge est bien câblée et en bonne condition électrique.
• La taille du câble est assez grosse pour l’intensité CC du chargeur tel que
spécifié dans la section 8.
1.7 Ne pas faire fonctionner le chargeur avec un cordon ou une prise endommagé –
remplacer immédiatement.
1.8 Ne pas faire fonctionner le chargeur s’il a reçu un choc violent, est tombé par
terre ou a été endommagé d’une autre façon; apportez-le à un technicien qualifié.
1.9 Ne pas démonter le chargeur; apportez-le chez un technicien qualifié lorsque vous
devez l’entretenir ou le réparer. Un mauvais remontage pourrait causer un risque
d’incendie ou de choc électrique.
1.10 Pour réduire le risque de choc électrique, débranchez le chargeur de la prise
murale avant de faire tout entretien ou nettoyage. Le fait de simplement éteindre
l’appareil ne réduira pas les risques.
1.11 AVERTISSEMENT : RISQUE DE GAZ EXPLOSIFS.
a.
IL EST DANGEREUX DE TRAVAILLER À PROXIMITÉ D’UNE BATTERIE AU PLOMB.
LES BATTERIES PRODUISENT DES GAZ EXPLOSIFS LORS DU
FONCTIONNEMENT NORMAL.
IL EST AUSSI IMPORTANT DE TOUJOURS RELIRE LES INSTRUCTIONS AVANT
D’UTILISER LE CHARGEUR ET DE LES SUIVRE À LA LETTRE.
b.
Pour réduire le risque d’explosion de la batterie, suivez ces directives et celles
publiées par le fabricant de la batterie et du fabricant de tout autre appareil que vous
pensez utiliser à proximité de la batterie. Examinez les avertissements inscrits sur
• 18 •
487802781
ces produits et sur le moteur.
2. MESURES DE SÉCURITÉ PERSONNELLE
2.1
Envisagez qu’une personne soit près de vous lorsque vous travaillez près d’un
accumulateur au plomb afin qu’elle puisse vous venir en aide en cas d’urgence.
2.2
Ayez assez d’eau fraîche et du savon à proximité au cas ou votre peau, vos yeux
ou vos vêtements viendraient en contact avec l’acide de la batterie.
2.3
Portez une protection complète des yeux et du corps, comprenant des lunettes
de sécurité et des vêtements protecteurs. Évitez de toucher vos yeux lorsque
vous travaillez près de la batterie.
2.4
Si l’acide de la batterie entre en contact avec votre peau ou vos vêtements, lavez
l’endroit immédiatement avec de l’eau et du savon. Si l’acide entre en contact
avec vos yeux, rincez immédiatement l’œil avec de l’eau courante froide pour au
moins 10 minutes, puis allez voir le médecin aussitôt.
2.5
Ne jamais fumer ou allumer des flammes à proximité de la batterie ou du moteur.
2.6
Soyez très prudent pour réduire le risque de laisser tomber un outil en métal sur la
batterie. Cela pourrait faire une étincelle ou produire un court-circuit à la batterie ou
à d’autres pièces électriques et pourrait produire une explosion.
2.7
Enlevez vos objets personnels en métal comme les bagues, les bracelets, les
colliers et les montres lorsque vous travaillez avec une batterie d’accumulateurs
au plomb. Une batterie d’accumulateurs au plomb peut produire un court-circuit
thermique assez fort pour souder une bague ou autre objet métallique
similaire, causant de graves brûlures.
2.8
Utilisez le chargeur pour les batteries 6 V et 12 V rechargeable au plomb-
acide, GEL et AGM avec une capacité recommandée de 12 Ah (6 V) et 12-59
Ah (12 V).
Il n’est pas conçu pour alimenter un système électrique à basse tension autre
que dans une application d’un démarreur. Ne pas utiliser ce chargeur de batterie
pour recharger des piles sèches qui sont couramment utilisées dans les
appareils électroménagers. Ces piles peuvent exploser et causer des blessures
et des dommages matériels.
2.9
NE JAMAIS charger une batterie gelée.
2.10
AVERTISSEMENT : Ce produit contient un ou plusieurs produits chimiques reconnus
par l’État de Californie pour causer le cancer, des malformations congénitales ou
d’autres troubles de la reproduction.
• 19 •
487802781
3. PRÉPARATION POUR LA CHARGE
3.1
S’il est nécessaire de retirer la batterie du véhicule pour la charger, toujours
débrancher la borne de mise à la masse en premier. S’assurer que le courant aux
accessoires du véhicule est coupé afin d’éviter la formation d’un arc.
3.2
Assurez-vous que la zone autour de la batterie est bien ventilée lorsque la
batterie est en charge.
3.3
Nettoyez les bornes de la batterie avant de la charger. Lors du nettoyage,
ne laissez pas les particules de corrosion entrer en contact avec vos yeux.
3.4
Ajoutez de l’eau distillée dans chaque élément de batterie jusqu’à que le
niveau d’acide atteigne celui spécifié par le fabricant de la batterie. Ne pas faire
déborder. Pour une batterie dont les éléments n’ont pas de bouchons, comme
les « VRLA » (accumulateur au plomb – acide à régulation par soupape) suivez
attentivement les directives de recharge du fabricant.
3.5
Étudiez toutes les précautions spécifiques du fabricant de la batterie pour l
charge et les taux de charge recommandés.
3.6
Si le chargeur comporte un sélecteur de tension de sortie, consultez le manuel
du propriétaire du véhicule pour déterminer la tension de la batterie et pour
s’assurer que la tension de sortie est appropriée. Si le chargeur n’est pas muni
d’un sélecteur, ne pas utiliser le chargeur à moins que la tension de la batterie ne
soit identique à la tension de sortie nominale du chargeur.
4. EMPLACEMENT DU CHARGEUR
4.1
Placez le chargeur aussi loin que possible de la batterie que les câbles CC le permettent.
4.2
Ne jamais placer le chargeur directement sous la batterie à charger; les gaz
ou les fluides qui s’échappent de la batterie peuvent entraîner la corrosion du
chargeur ou l’endommager.
4.3
Ne jamais laisser l’électrolyte de la batterie s’écouler sur le chargeur lors de
l’analyse hydrométrique ou en remplissant la batterie.
4.4
Ne pas faire fonctionner le chargeur dans un espace clos et/ou ne pas gêner la ventilation.
4.5
Ne pas poser la batterie sur le chargeur.
5. PRÉCAUTIONS SUR LA CONNEXION C.C.
5.1 Mettre les interrupteurs du chargeur hors circuit et retirer le cordon C.A. de la
prise avant de mettre et d’enlever les pinces du cordon C.C. S’assurer que les
pinces ne se touchent pas.
5.2 Attachez les pinces à la batterie et au châssis, comme indiqué dans les sections 6 et 7.
• 20 •
487802781
6. ÉTAPES À SUIVRE LORSQUE LA BATTERIE EST INSTALLÉE DANS UN VÉHICULE
NOTE : Une batterie marine (bateau/Motomarine) doit être retirée du véhicule
pour être chargée. Pour la recharge à bord, un équipement spécialement conçu
pour utilisation marine doit être utilisé.
AVERTISSEMENT : UNE ÉTINCELLE PRÈS DE LA BATTERIE POURRAIT LA
FAIRE EXPLOSER. POUR RÉDUIRE LES RISQUES D’ÉTINCELLE PRÈS DE LA
BATTERIE :
6.1
Placer les cordons C.A. et C.C. de manière à éviter qu’ils soient endommagés par le
capot, une portière ou les pièces en mouvement du moteur.
6.2
Faire attention aux pales, aux courroies et aux poulies du ventilateur ainsi qu’à
toute autre pièce susceptible de causer des blessures.
6.3
Vérifier la polarité des bornes de la batterie. Le diamètre de la borne POSITIVE
(POS, P, +) est généralement supérieur à celui de la borne NÉGATIVE (NÉG, N, –).
6.4
Déterminer quelle borne est mise à la masse (raccordée au châssis). Si la borne
négative est raccordée au châssis (comme dans la plupart des cas), voir l’étape
6.5. Si la borne positive est raccordée au châssis, voir l’étape 6.6.
6.5
Si la borne négative est mise à la masse, raccorder la pince POSITIVE (ROUGE)
du chargeur à la borne POSITIVE (POS, P, +) non mise à la masse de la batterie.
Raccorder la pince NÉGATIVE (NOIRE) au châssis du véhicule ou au moteur,
loin de la batterie. Ne pas raccorder la pince au carburateur, aux canalisations
d’essence ni aux pièces de la carrosserie en tôle. Raccorder à une pièce du cadre
ou du moteur en tôle de forte épaisseur.
6.6
Si la borne positive est mise à la masse, raccorder la pince NÉGATIVE (NOIRE)
du chargeur à la borne NÉGATIVE (NÉG, N, –) non mise à la masse de la
batterie. Raccorder la pince POSITIVE (ROUGE) au châssis du véhicule ou
au moteur, loin de la batterie. Ne pas raccorder la pince au carburateur, aux
conduits d’essence ni aux pièces de la carrosserie en tôle. Raccorder à une
pièce du cadre ou du moteur en tôle de forte.
6.7
Pour interrompre l’alimentation du chargeur, mettre les interrupteurs hors circuit,
retirer le cordon C.A. de la prise, enlever la pince raccordée au châssis et, en
dernier lieu, celle raccordée à la batterie.
6.8 Voir Consignes d’utilisation pour des renseignements sur la durée de charge.
7. ÉTAPES À SUIVRE LORSQUE LA BATTERIE EST INSTALLÉE HORS DU VÉHICULE
AVERTISSEMENT : UNE ÉTINCELLE PRÈS DE BATTERIE POURRAIT LA FAIRE
EXPLOSER. POUR RÉDUIRE LES RISQUES D’ÉTINCELLE PRÈS DE LA BATTERIE :
7.1
Vérifier la polarité des bornes de la batterie. Le diamètre de la borne POSITIVE
(POS, P, +) est généralement supérieur à celui de la borne NÉGATIVE (NÉG, N, –).
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
Schumacher BRP 715005061 Automatic Battery Charger Le manuel du propriétaire
- Catégorie
- Chargeurs de batterie de voiture
- Taper
- Le manuel du propriétaire
dans d''autres langues
Documents connexes
-
Schumacher Schumacher 715005061 Le manuel du propriétaire
-
-
-
-
-
Schumacher SP1297 Automatic Battery Charger Le manuel du propriétaire
-
-
-
-