GE HSM25GFBSA Le manuel du propriétaire

Marque: GE

Modèle: HSM25GFBSA

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Hotpoint.com

Refrigerators

Side by Side

162D6746P013 39-60516-2 09-10 GE

Write your model and serial numbers here:

Model # _____________________

Serial # _____________________

Find these numbers on a label inside the

refrigerator compartment at the top on the

right side behind the controls.

Réfrigérateurs

Côte à côte

Manuel d’utilisation

et d’installation

La section française commence à la page 23

Safety Information

Connect Electricity . . . . . . . . . . . . . . .3

Extension Cords . . . . . . . . . . . . . . . . .2

Proper Disposal . . . . . . . . . . . . . . . . .2

Safety Precautions . . . . . . . . . . . . . . .2

Operating Instructions

Automatic Icemaker . . . . . . . . . . . .7–8

Controls . . . . . . . . . . . . . . . . . . . . . . .6

Crispers and Pans . . . . . . . . . . . . . . . .5

How to Install Features . . . . . . . . . . . .4

Ice and Water Dispenser . . . . . . . . . .8

Shelves and Bins . . . . . . . . . . . . . . . . .4

Water Filter Cartridge . . . . . . . . . . . .7

Care and Cleaning

Cleaning . . . . . . . . . . . . . . . . . . . . . . .9

Light Bulbs . . . . . . . . . . . . . . . . . . . .9

Installation Instructions

Preparing to Install . . . . . . . . . . . . .10

Water Line Installation . . . . . . . .11–13

Troubleshooting Tips

Before You Call

For Service . . . . . . . . . . . . . . . . .14–16

Normal Operating Sounds . . . . . . . .14

Consumer Support

Consumer Support . . . . . .Back Cover

Performance Data Sheet . . . . . . . . .19

Product Registration

(Canadian) . . . . . . . . . . . . . . . . .21, 22

Product Registration

(U.S.) . . . . . . . . . . . . . . . . . . . . . .20, 21

State of California Water

Treatment Device Certificate . . . . . .19

Warranty (Canadian) . . . . . . . . . . . .17

Warranty (U.S.) . . . . . . . . . . . . . . . . .18

Refrigeradores

Lado a lado

Models 20, 22, 25

Owner’s Manual and

Installation Instructions

Manual del propietario e

instalación

La sección en español empieza en la página 42

Refrigerators

Side by Side

Mesures de sécurité

Comment vous débarrasser

convenablement de votre

ancien réfrigérateur . . . . . . . . . . . . . . . . . . .23

Cordons prolongateurs . . . . . . . . . . . . . . . .23

Mesures de sécurité . . . . . . . . . . . . . . . . . . .23

Raccordement électrique . . . . . . . . . . . . . .24

Fonctionnement

Bacs à légumes . . . . . . . . . . . . . . . . . . . . . . .26

Cartouche du filtre à eau . . . . . . . . . . . . . . .28

Clayettes et bacs . . . . . . . . . . . . . . . . . . . . . .25

Installation des accessoires . . . . . . . . . . . . . .25

Le distributeur d’eau et de glaçons . . . . . . . .29

Les commandes . . . . . . . . . . . . . . . . . . . . . .27

Machine à glaçons automatique . . . . . . . .28–29

Entretien et nettoyage

Nettoyage . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Remplacement des ampoules . . . . . . . . . . .30

Installation

Installation de la

conduite d’eau . . . . . . . . . . . . . . . . . . . .32–34

Préparation . . . . . . . . . . . . . . . . . . . . . . . . . .31

Conseils de dépannage

Avant d’appeler un réparateur . . . . . . . .35–38

Bruits de fonctionnement

normaux . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Service à la clientèle

Feuillet de données relatives à la

performance de la

cartouche HWF . . . . . . . . . . . . . . . . . . . . . .40

Garantie pour la

clientèle au Canada . . . . . . . . . . . . . . . . . . .39

Service à la clientèle . . . . . . . . . . . . . . . . . . .41

Información de seguridad

Cables de extensión . . . . . . . . . . . . . . . . . . . 42

Conectar la electricidad. . . . . . . . . . . . . . . . 43

Deshacerse debidamente

de su refrigerador. . . . . . . . . . . . . . . . . . . . . 42

Precauciones de seguridad . . . . . . . . . . . . . 42

Instrucciones de operación

Cartucho del filtro de agua . . . . . . . . . . . . . 47

Controles del refrigerador . . . . . . . . . . . . . . 46

Dispensador . . . . . . . . . . . . . . . . . . . . . . . . . 48

Dispositivo automático

para hacer hielo . . . . . . . . . . . . . . . . . . . 47–48

Entrepaños y recipientes . . . . . . . . . . . 44–45

Gavetas de almacenamiento . . . . . . . . . . . . 45

Instalación de las características . . . . . . . . . 44

Cuidado y limpieza

Limpieza. . . . . . . . . . . . . . . . . . . . . . . . . 49–50

Reemplazo de bombillas. . . . . . . . . . . . . . . 50

Instrucciones de instalación

Instalación de la línea

de agua . . . . . . . . . . . . . . . . . . . . . . . . . . 53–56

Preparación para

instalar el refrigerador . . . . . . . . . . . . . . 51–52

Solucionar problemas

Antes de solicitar un servicio . . . . . . . . 57–60

Sonidos normales

de la operación. . . . . . . . . . . . . . . . . . . . . . . 57

Servicio al consumidor

Garantía para consumidores

en los Estados Unidos . . . . . . . . . . . . . . . . . 61

Hoja de datos de

funcionamiento . . . . . . . . . . . . . . . . . . . . . . 62

Servicio al consumidor . . . . . . . . . . . . . . . . 63

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous…even if they will sit for “just a few days.” If

you are getting rid of your old refrigerator, please follow

the instructions below to help prevent accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

 Take off the doors.

 Leave the shelves in place so that children may not

easily climb inside.

Refrigerants

All refrigeration products contain refrigerants, which

under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend

against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a

CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet

and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:



 This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.



 Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could damage

the refrigerator and seriously injure themselves.



 Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin may

stick to these extremely cold surfaces.



 Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

NOTE: Turning the refrigerator off via the controls on

the touch panel does not shut off electrical power to

the refrigerator.



 Do not refreeze frozen foods which have thawed

completely.



 In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element that

releases the cubes. Do not place fingers or hands on

the automatic icemaking mechanism while the

refrigerator is plugged in.



 Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.



 Unplug the refrigerator before cleaning and making

repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

www.Hotpoint.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must

be properly grounded.



 The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock

hazard from this appliance.



 Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is

properly grounded.



 If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong wall outlet.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

INSURE PROPER GROUND EXISTS

BEFORE USE



 The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating that

matches the rating plate.



 This provides the best performance and also prevents

overloading house wiring circuits which could cause a fire

hazard from overheated wires.



 Never unplug your refrigerator by pulling on the power cord.

Always grip plug firmly and pull straight out from the outlet.



 Repair or replace immediately all power cords that have

become frayed or otherwise damaged. Do not use a cord that

shows cracks or abrasion damage along its length or at either

end.



 When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

How to install features. (Not all features are on all models.)

Top Freezer Shelf

➀ TOP FREEZER SHELF

Make sure the shelf front locks into

position.

Lower Door Bin

➅ LOWER FIXED DOOR BINS

Make sure the bin fronts lock into position.

➄ ADJUSTABLE

DOOR BINS

DOOR BIN SNUGGERS

➂ DAIRY COVER

➃ BOTTLE RETAINER

Door

Shelf Front

Door

Shelf

➁ FILTER CARTRIDGE

➆

FREEZER DOOR SHELF FRONTS

Make sure that the shelf front locks

into position.

NOTE: On dispenser models, the

longer shelf fronts go in the top

two positions.

Remove Bypass Plug Install Filter Cartridge

To remove: Lift the front

of the bin up, then pull

out.

To replace or relocate:

Engage the bin in the

molded supports of the

door, and push in. Bin

will lock in place.

To remove: Lift the shelf extender

straight up, then pull out.

To replace: Engage the shelf

extender in the molded supports of

the door and push in. It will lock in

place.

About the shelves and bins. (Not all features are on all models.)

Rearranging the Shelves

To Remove

To Replace

Refrigerator Shelves:

Lift up and out

Tilt up

Insert

top hook

Lower to

lock in

place

To Remove

Freezer Shelves:

To Remove

Freezer Pan:

Remove the pan by pulling it

forward, lifting up the front and

sliding it past the stop location.

Slide-Out Spillproof Shelf

(on some models)

The slide-out spillproof shelf allows you to

reach items stored behind others. The special

edges are designed to help prevent spills from

dripping to lower shelves.

NOTE: Make sure you push the shelves all the

way back in before you close the door.

Spillproof Shelves (on some models)

Spillproof shelves have special edges

to help prevent spills from dripping to

lower shelves.

www.Hotpoint.com

About the crispers and pans. (Not all features are on all models.)

Adjustable Humidity Crispers and Snack Pan (on some models)

Slide the control all the way to the

High setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the Low setting

to provide lower humidity levels recommended

for most fruits.

LOW

HIGH

LOW

HIGH

Convertible Meat Pan (on some models)

The convertible meat pan has its own cold air

duct to allow a stream of cold air from the

freezer compartment to flow around

the pan.

The variable temperature control regulates the air

flow from the freezer compartment.

Set control lever up to convert the pan

to normal refrigerator temperature and provide

extra vegetable storage space. Cold air duct is

turned off. Variable settings between these

extremes can be selected.

Set control lever down to the coldest setting to

store fresh meats. If lever is left in meat position

for a long period of time, some frost may form

on the inside of the pan.

Normal

Coldest

Crisper Removal

Crispers can easily be removed by tilting up

slightly and pulling past stop location.

If the door prevents you from taking out

the crispers, the refrigerator will need to

be rolled forward until the door opens enough

to slide the crispers out. In some cases, when

you roll the refrigerator out, you will need to

move the refrigerator to

the left as you roll it out.

When replacing the crispers, make

sure you slide them through the

crisper guides.

About the controls on the refrigerator.

9 IS COLDES

0 IS OFF

9 IS COLDEST

0 IS OFF

FREEZER FRESH FOOD

Your controls will look like one of the following:

Startup Steps for Proper Temperature Control

STEP 1—Set Fresh Food Control on “5.”

STEP 2—Set Freezer Control on “5.”

STEP 3—WAIT 12 HOURS for temperature to stabilize.

STEP 4—If a change is needed, move the control one number at a time and allow 12 hours for

temperature to stabilize.

NOTE: Turning the refrigerator to the

(off) setting via the controls does not shut off electrical

power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating

conditions and may require more than one adjustment.

0 IS OFF

9 IS COLDEST

FREEZER

REFRIGERATOR

To Change Temperature Control Setting with Touch Pads:

• Freezer setting is on the left side of the display.

• Refrigerator setting is on the right side of the display.

— Press the Warmer or Colder pad for compartment and direction desired.

— Present control setting number will illuminate.

— Each time the pad is touched, compartment setting changes one number.

A display of 1 is warmest and 9 is the coldest setting.

To Turn Cooling Off:

To stop cooling in the refrigerator and freezer compartments, first repeatedly press

the Warmer pad for the freezer until its display continuously flashes “1”. Then, using

the refrigerator control, repeatedly press Warmer until both displays flash “0”. “0” in both displays

turns off the cooling system. On some models, it may be necessary to set only

one control to

to turn off cooling in both compartments.

NOTE: Turning the refrigerator to the

(off) setting via the controls does not shut off electrical

power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating

conditions and may require more than one adjustment.

About the water filter cartridge. (On some models.) www.Hotpoint.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right

corner of the refrigerator compartment.

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter

cartridge on the dispenser. This light will turn orange to tell you

that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement

indicator light turns red or if the flow of water to the dispenser or

icemaker decreases.

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced every six months

or earlier if the flow of water to the water dispenser or icemaker

decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by

slowly turning it to the left. Do not pull down on the cartridge. A

small amount of water may drip down.

Installing the Filter Cartridge

If you are replacing a

SmartWater cartridge

with an adapter, it must

be removed before

installing the cartridge.

To remove the adapter,

turn it to the left about

1/4 turn.

If you are replacing a

Water by Culligan cartridge,

leave the adapter in place.

This adapter will stay in the refrigerator when you replace

future cartridges.

On models without a replacement indicator light,

apply the month and year sticker to the new cartridge to

remind you to replace the filter in six months.

Fill the replacement cartridge with water from the tap to

allow for better flow from the dispenser immediately after

installation.

Line up the arrow on the cartridge and the cartridge holder.

Place the top of the new cartridge up inside the holder. Do

not push it up into the holder.

Slowly turn it to the right until

the filter cartridge stops. DO

NOT OVERTIGHTEN. As you turn

the cartridge, it will

automatically raise itself into

position. The cartridge will

move about 1/2 turn.

un water from the dispenser

for 1-1/2 gallons (about three

minutes) to clear the system and prevent sputtering.

Press and hold the RESET WATER FILTER pad (on

some models) on the dispenser for three seconds.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter

cartridge is not available. The dispenser and the icemaker will not

operate without the filter or filter bypass plug.

To use the filter bypass plug on Water by Culliganmodels, you must first remove

the filter adapter from the cartridge holder by turning it to the left.

For the maximum benefit of your filtration system, GE

recommends the use of GE branded SmartWater filters only.

Using GE branded filters in GE and Hotpoint refrigerators

provides optimal performance and reliability. GE branded

SmartWater filters are always the right choice because they are

patented and designed specifically for GE products. GE

SmartWater filters meet rigorous industry NSF standards for

safety and quality that are important for products that are

filtering your water. GE has not qualified non-GE branded filters

for use in GE and Hotpoint refrigerators and there is no

assurance that non-GE branded filters meet GE’s standards for

quality, performance and reliability.

If you have questions—visit our Website

at www.hotpoint.com,

or call 1.800.GE.CARES (1.800.432.2737).

Replacement filters:

To order additional filter cartridges in the United States,

visit our Website at www.hotpoint.com, or call GE Parts and

Accessories, 800.626.2002.

MWF

Suggested Retail $38.95–47.95

Customers in Canada should consult the yellow pages for the

nearest Mabe Service Center.

Customers outside of the United States or Canada should

contact the local distributor.

Cartridge

Holder

Filter

Bypass

Plug

Filter

Bypass

Plug

SmartWater

Water by Culligan

(appearance may vary)

With adapter

Without adapter

About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Icemaker

Feeler Arm

Power Switch

Automatic Icemaker(on some models)

When the refrigerator has been connected to

the water supply, slide the power switch to the

ON position.

The icemaker will fill with water when

it cools to 15°F. When the bin fills to the level

of the feeler arm, the icemaker will stop

producing ice.

Be sure nothing interferes with the sweep of the

feeler arm.

Throw away the first few batches of ice to allow

the water line to clear.

The icemaker will produce seven cubes per

cycle—approximately 100–130 cubes in a 24-

hour period, depending on freezer

compartment temperature, room

temperature, number of door openings and

other use conditions.

You will hear a buzzing sound each time the

icemaker fills with water.

About the automatic icemaker.

It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become

cloudy, taste stale, and shrink.

Icemaker Accessory Kit

If your refrigerator did not come already equipped

with an automatic icemaker, an icemaker accessory kit

is available at extra cost. Check the back of the

refrigerator for the specific icemaker kit needed for

your model.

Select or

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To reduce

water spotting, the shelf and its grille should be

cleaned regularly.

Locking the Dispenser (on some models)

Press the Lock pad

for 3 seconds to lock the

dispenser and control panel. To

unlock, press and hold

the pad again for 3 seconds.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water line

and to fill the water system. To flush out impurities

in the water line, throw away the first six glassfuls

of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Dispenser Light

This pad turns the night light in

the dispenser on and off. The

light also comes on when the

dispenser cradle is pressed. If this

light burns out, it should be

replaced with a 6 watt maximum,

12 volt DC bulb.

About the ice and water dispenser. (On some models.)

To Use the Dispenser

Important Facts About Your Dispenser

 Do not add ice from trays or bags to the storage bin. It may

not crush or dispense well.

 Avoid overfilling glass with ice and use of narrow glasses.

Backed-up ice can jam the chute or cause the door in the

chute to freeze shut. If ice is blocking the chute, poke it

through with a wooden spoon.

 Beverages and foods should not be quick-chilled in the ice

storage bin. Cans, bottles or food packages in the storage bin

may cause the icemaker or auger to jam.

 To keep dispensed ice from missing the glass, put the glass

close to, but not touching, the dispenser opening.

 Some crushed ice may be dispensed even though you selected

Cubed. This happens occasionally when a few cubes have been

left in the crusher.

 After crushed ice is dispensed, some water may drip from the

chute.

 Sometimes a small mound of snow will form on the door in

the ice chute. This condition is normal and usually occurs

when you have dispensed crushed ice repeatedly. The snow

will eventually evaporate.

 The first glass of water dispensed may be warmer than the

following ones. This is normal.

 Dispensed water is not ice cold. For colder water, simply add

crushed ice or cubes before dispensing water.

Ice Storage Drawer on Dispenser Models

To remove:

Slide the icemaker power switch to the OFF position. Pull

the drawer straight out and then lift past the stop position.

To replace:

When replacing the drawer, make sure to push it firmly

into place. If it does not go all the way back, remove it and

rotate the drive mechanism 1/4 turn. Then push the

drawer back again.

Drive

Mechanism

Rotate

Spill Shelf

Care and cleaning of the refrigerator. www.Hotpoint.com

Cleaning the Outside

The dispenser drip area, (on some models)

beneath the grille, should be wiped dry. Water left

in this area may leave deposits. Remove the

deposits by adding undiluted vinegar to the

well. Soak until the deposits disappear or

become loose enough to rinse away.

The dispenser cradle (on some models). Before

cleaning, lock the dispenser by pressing and

holding the Lock pad for

3 seconds. Clean with warm water and baking

soda solution—about a tablespoon (15 ml) of

baking soda to a quart (1 l)

of water. Rinse thoroughly and wipe dry.

The door handles and trim. Clean with a

cloth dampened with soapy water. Dry

with a soft cloth.

Keep the outside clean. Wipe with a clean cloth

lightly dampened with kitchen appliance wax or

mild liquid dish detergent. Dry and polish with

a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning. If this is

not practical, wring excess moisture out of

sponge or cloth when cleaning around switches,

lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda to a

quart (1 l) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin

layer of petroleum jelly to the door gaskets at

the hinge side. This helps keep the gaskets from

sticking and bending out

of shape.

Drain opening in freezer compartment.

During yearly cleaning, remove bottom freezer

pan and flush a solution of baking soda—1

teaspoon (5 ml) and 2 cups (500 ml) of hot (not

boiling) water— through the drain line with the

help of a meat baster. This will help eliminate

odor and reduce the likelihood of a clogged

drain line. If drain becomes clogged, use a

meat baster and baking soda solution to force

the clog through the drain line.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference may

cause them to break. Handle glass shelves carefully.

Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the

dishwasher.

For long vacations or absences, remove food and unplug the

refrigerator. Clean the interior with a baking soda solution of

one tablespoon (15 ml) of baking soda to one quart (1 l) of water.

Leave the doors open.

Slide the icemaker power switch to the OFF position and shut off

the water supply to the refrigerator.

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All

types of floor coverings can be damaged, particularly cushioned

coverings and those with embossed surfaces.

Pull the refrigerator straight out and return it to position by

pushing it straight in. Moving the refrigerator in a side direction

may result in damage to the floor covering or refrigerator.

When pushing the refrigerator back, make sure you don’t roll over

the power cord or icemaker supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as grille, shelves and drawers by taping them securely in place to prevent damage.

Be sure the refrigerator stays in an upright position during moving.

NOTE: Turning the refrigerator to the 0 (off) setting via the controls does not shut off electrical power to the refrigerator.

Replacing the Light Bulbs

Unplug the refrigerator.

Remove the shelf just below the light shield.

Replace with an appliance bulb of the same

or lower wattage.

Reinstall the shelf and plug the refrigerator

back in.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT

–

Save these instructions

for local inspector’s use.

•

IMPORTANT

–

Observe all governing

codes and ordinances.

•

Note to Installer

–

Be sure to leave these

instructions with the Consumer.

•

Note to Consumer

–

Keep these instructions for

future reference.

•

Skill level

– Installation of this appliance requires basic

mechanical skills.

•

Completion time

– Refrigerator Installation

15 minutes

• Proper installation is the responsibility of installer.

• Product failure due to improper installation is not

covered under the Warranty.

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will

go below 60°F (16°C) because it will not run often enough

to maintain proper temperatures.

• Install it on a floor strong enough to support it fully

loaded.

Installation Instructions

Models 20, 22, 25

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical connections.

•

Sides

1/8”(4 mm) •

Top

1” (25 mm) •

Back

1” (25 mm)

A door clearance of 3/4” (19 mm) is needed for a 90º door

opening which provides better access to food storage area.

CLEARANCES

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A GE water supply kit is

available at extra cost from your dealer, by visiting our

Website at

www.Hotpoint.com

(in Canada, at

www.geappliances.ca

), or from Parts and Accessories,

800.626.2002.

WATER SUPPLY TO THE ICEMAKER (on

some models)

Questions? Call 800.GE.CARES (800.432.2737)

Visit our Website at: www.Hotpoint.com

Questions? In Canada, call 1.800.561.3344

Visit our Website at: www.geappliances.ca

The rollers have 3 purposes:

 Rollers adjust so the door closes easily when opened about

halfway.

 Rollers adjust so the refrigerator is firmly positioned on the

floor and does not wobble.

 Rollers allow you to move the refrigerator away from the

wall for cleaning.

To adjust the rollers,

remove the base grille by pulling it out at

the bottom.

Turn the roller adjusting screws

clockwise to raise

the

refrigerator,

counterclockwise to lower

it. Use an adjustable

wrench (3/8”hex head bolt) or pliers.

To replace base grille,

line up the clips on back of grille

between the bar and the bottom of the cabinet. Push forward

until grille snaps into place.

ROLLERS

To remove the base

grille, open the doors

and then pull the

grille straight out.

5/16”Socket

Wrench

Raise

DOOR ALIGNMENT

After leveling, make sure that doors are even at the top.

To make the doors even,

adjust the refrigerator door.

Using a 5/16” socket wrench, turn the door adjusting screw

to the right to raise the door, to the left to lower it. (A nylon

plug, embedded in the threads of the pin, prevents the pin

from turning unless a wrench is used.)

After one or two turns of the wrench, open and close the

refrigerator compartment door and check the alignment at

the top of the doors.

Installation Instructions

INSTALLING THE WATER LINE

Recommended copper water supply kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of tubing

you need. Approved plastic water supply lines are GE

SmartConnect

™

Refrigerator Tubing (WX08X10002,

WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis

Water System, the only approved installation

is with a GE RVKit. For other reverse osmosis water systems,

follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse

Osmosis Water Filtration System AND the refrigerator also

has a water filter, use the refrigerator’s filter bypass plug.

Using the refrigerator’s water filtration cartridge in

conjunction with the RO filter can result in hollow ice cubes

and slower water flow from the water dispenser.

This water line installation is not warranted by the

refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive water

damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and lead to

water leakage or flooding. Call a qualified plumber to correct

water hammer before installing

the water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the water line,

make sure the icemaker power switch is in the OFF position.

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

All installations must be in accordance with local plumbing

code requirements.

WARNING –

Connect to potable water

supply only.

BEFORE YOU BEGIN

•

Copper or GE SmartConnect

™

Refrigerator Tubing kit

1/4” outer diameter to connect the refrigerator to the

water supply. If using copper, be sure both ends of the

tubing are cut square.

To determine how much tubing you need: measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Be sure there is

sufficient extra tubing to allow the refrigerator to move out

from the wall after installation.

GE SmartConnect

™

Refrigerator Tubing Kits are available

in the following lengths:

2′ (0.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

WHAT YOU WILL NEED

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect™ Refrigerator Tubing kits.

Do not use any other plastic water supply line because the

line is under pressure at all times. Certain types of plastic

will crack or rupture with age and cause water damage to

your home.

•

A GE water supply kit

(containing tubing, shutoff valve

and fittings listed below) is available at extra cost from

your dealer or from Parts and Accessories,

800.626.2002.

•

A cold water supply

. The water pressure must be between

20 and 120 p.s.i. (1.4–8.2 bar) on models without a water

filter and between 40 and 120 p.s.i. (2.8–8.2 bar) on

models with a water filter.

•

Power drill.

•

1/2

”

or adjustable wrench.

•

Straight and Phillips blade screwdriver.

•

Two 1/4

”

outer diameter compression nuts and

2 ferrules (sleeves)

—to connect the copper tubing

to the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect™ Refrigerator

Tubing kit, the necessary fittings are preassembled to the

tubing.

• If your existing copper water line has a flared fitting at

the end, you will need an

adapter

(available at plumbing

supply stores) to connect the water line to the refrigerator

you can cut off the flared fitting

with a

tube cutter

and then use a compression fitting. Do

not cut formed end from GE SmartConnect™

Refrigerator tubing.

•

Shutoff valve

to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32” at the point of

connection to the

COLD WATER LINE

. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve complies

with your local plumbing codes. Install the shutoff valve

on the nearest frequently used drinking water line.

WHAT YOU WILL NEED (CONT.)

Installation Instructions

SHUT OFF MAIN WATER SUPPLY

Choose a location for the valve that is easily accessible.

It is best to connect into the side of a vertical water

pipe. When it is necessary to connect into a horizontal

water pipe, make the connection to the top or side,

rather than at the bottom,

to avoid drawing off any sediment from the

water pipe.

Drill a 1/4” hole in the water pipe (even if using a self-

piercing valve) using a sharp bit. Remove any burrs

resulting from drilling the hole in the pipe.

Take care not

to allow water to drain into the drill.

Failure to drill a

1/4” hole may result in reduced ice production or

smaller cubes.

DRILL THE HOLE FOR THE VALVE

Fasten the shutoff valve to the cold water pipe with the

pipe clamp.

Tighten the clamp screws until the sealing washer begins

to swell.

NOTE:

Do not overtighten or you may crush the

tubing.

NOTE:

Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves are

illegal and use is not permitted in Massachusetts. Consult

with your licensed plumber.

FASTEN THE SHUTOFF VALVE

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Pipe Clamp

Clamp Screw

Washer

Inlet End

Route the tubing between the cold water line and the

refrigerator.

Route the tubing through a hole drilled in the wall or

floor (behind the refrigerator or adjacent base cabinet)

as close to the wall as possible.

NOTE:

Be sure there is sufficient extra tubing

to allow the refrigerator to move out from the wall after

installation.

ROUTE THE TUBING

Place the compression nut and ferrule (sleeve) for copper

tubing onto the end of the tubing and connect it to the

shutoff valve.

Make sure the tubing is fully inserted into the valve.

Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand tight, then tighten one

additional turn with a wrench. Overtightening may

cause leaks.

CONNECT THE TUBING TO THE VALVE

Turn the main water supply on and flush out the tubing

until the water is clear.

FLUSH OUT THE TUBING

NOTE:

Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves are

illegal and use is not permitted in Massachusetts. Consult

with your licensed plumber.

Saddle-Type

Shutoff Valve

Compression Nut

SmartConnect™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

NOTES:

• Before making the connection to the refrigerator, be

sure the refrigerator power cord is not plugged into

the wall outlet.

• If your refrigerator does not have a water filter, we

recommend installing one if your water supply has

sand or particles that could clog the screen of the

refrigerator’s water valve. Install it in the water line

near the refrigerator. If using a GE SmartConnect™

Refrigerator Tubing kit, you

will need an additional tube (WX08X10002)

to connect the filter. Do not cut plastic tube

to install filter.

CONNECT THE TUBING TO THE

REFRIGERATOR

Installation Instructions

Place the compression nut and ferrule (sleeve) onto the

end of the tubing as shown. On a GE SmartConnect

™

Refrigerator Tubing kit, the nuts

are already assembled to the tubing.

Insert the end of the tubing into the refrigerator

connection as far as possible. While holding the tubing,

tighten the fitting.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end of the

tubing into the refrigerator connection and tighten the

compression nut until it is hand tight, then tighten one

additional turn with a wrench. Overtightening may

cause leaks.

Fasten the tubing into the clamp provided as shown to

keep it in position. You may need to pry open the

clamp.

One of the illustrations below will look like the

connection on your refrigerator.

On models using the refrigeration connection at the

water valve, remove the plastic flexible cap.

CONNECT THE TUBING TO THE

REFRIGERATOR

(CONT.)

Some models have the refrigerator connection at the

end of tubing located outside the compressor

compartment access cover. On other models, the

compressor compartment access cover must be removed

in order to access the refrigerator connection at the

water valve.

1/4”

Compression

Nut

Tubing

Clamp

1/4”

Tubing

Refrigerator

Connection

SmartConnect™

Tubing

Ferrule

(sleeve)

Tighten any connections that leak.

TURN THE WATER ON AT THE

SHUTOFF VALVE

CONNECT THE TUBING TO THE

REFRIGERATOR

(CONT.)

Reattach the access cover.

SmartConnect™

Tubing

1/4”

Compression

Nut

1/4”

Tubing

Arrange the coil of tubing so that it does not vibrate

against the back of the refrigerator or against the wall.

Push the refrigerator back to the wall.

PLUG IN THE REFRIGERATOR

START THE ICEMAKER

Slide the icemaker power switch to the ON position. The

icemaker will not begin to operate until it reaches its

operating temperature of 15°F (-9°C)

or below. It will then begin operation automatically if

the icemaker power switch is in the ON position.

Tubing

Clamp

Refrigerator

Connection

Ferrule

(sleeve)

Normal operating sounds.

The new high efficiency compressor runs faster and will have a higher pitch hum or

pulsating sound while operating.

The fan circulating air inside the freezer which keeps the temperatures throughout.

Water dropping on the defrost heater causing a sizzling, hissing or popping

sound during the defrost cycle.

The flow of refrigerant through the freezer cooling coils sounds like boiling

water or a gurgling noise.

Cracking or popping of cooling coils caused by expansion and contraction

during defrost and refrigeration following defrost.

Water dripping as it melts from the evaporator and flows to the drain pan

during the defrost cycle.

Icemaker (on some models)

The icemaker water valve will buzz when the icemaker fills with water. If the

power switch is in the ON position it will buzz even if it has not yet been hooked up to

water. Keeping the power switch in the ON position before it is hooked

up to water can damage the icemaker. To prevent this, slide the power switch to the OFF

position. This will stop the buzzing.

The sound of cubes dropping into the bin and water running in pipes as

icemaker refills.

Troubleshooting Tips

Save time and money! Review the charts on the following

pages first and you may not need to call for service.

Problem Possible Causes What To Do

Refrigerator does not

Refrigerator in defrost cycle.

•Wait about 30 minutes for defrost cycle to end.

operate

Freezer control

•Move the freezer control to a lower temperature setting.

0 (off)

position.

Refrigerator is unplugged.

•Push the plug completely into the outlet.

The fuse is blown/circuit

•Replace fuse or reset the breaker.

breaker is tripped.

Refrigerator or freezer

Temperature control not set

•See About the controls.

compartment too warm

cold enough.

Warm weather or frequent

•Set the temperature control one step colder.

door openings.

See About the controls.

Door left open.

•Check to see if package is holding door open.

These sounds are normal and are due mostly to highly efficient operation.

Before you call for service…

Newer refrigerators sound different from older refrigerators. Modern refrigerators have

more features and use newer technology.

Do you hear what I hear? These sounds are normal.

Problem Possible Causes What To Do

Vibration or rattling

Front rollers need adjusting. •

See Rollers. Slight vibration is normal.

Motor operates for

Normal when refrigerator

•Wait 24 hours for the refrigerator to completely

long periods or cycles

is first plugged in.

cool down.

on and off frequently.

Often occurs when large

•This is normal.

(Modern refrigerators

amounts of food are

with more storage

placed in refrigerator.

space and a larger

Door left open.

•Check to see if package is holding door open.

freezer require more

Hot weather or frequent

•This is normal.

operating time. They

door openings.

start and stop often

Temperature controls

•See About the controls.

to maintain even

set at the coldest

temperatures.)

setting.

Frost or ice crystals

Door left open.

•Check to see if package is holding door open.

on frozen food

Too frequent or too long

(frost within package

door openings.

is normal)

Divider between

Automatic energy saver

•This helps prevent condensation on the outside.

refrigerator and freezer

system circulates warm

compartments

liquid around front edge

feels warm

of freezer compartment.

Automatic icemaker

Icemaker power switch

•Slide the power switch to the ON position.

does not work

is in the

OFF

position.

(on some models)

Water supply turned off or

•See Installing the water line.

not connected.

Freezer compartment

•Wait 24 hours for the refrigerator to completely

too warm.

cool down.

Piled up cubes in the storage

•Level cubes by hand.

bin cause icemaker to shut off.

Ice cubes stuck in icemaker.

•Turn off the icemaker, remove cubes and turn the

icemaker back on.

Ice cubes have

Ice storage bin needs cleaning.

•Empty and wash bin. Discard old cubes.

odor/taste

Food transmitting odor/taste

•Wrap foods well.

to ice cubes.

Interior of refrigerator

•See Care and cleaning.

needs cleaning.

Small or hollow cubes

Water filter clogged.

•Replace filter cartridge with new cartridge or with plug.

Slow ice cube freezing

Door left open.

•Check to see if package is holding door open.

Temperature control not set

•See About the controls.

cold enough.

Door not closing

Door gasket on hinge side

•Apply petroleum jelly on face of gasket.

properly

sticking or folding over.

Orange glow in freezer

Defrost heater is on.

•This is normal.

Cube dispenser does not

Icemaker or water supply

•Turn on icemaker or water supply.

work (on some models)

turned off.

Ice cubes are frozen to

•Remove cubes.

icemaker feeler arm.

Irregular ice clumps in

•Break up with fingertip pressure and discard

storage container.

remaining clumps.

•Freezer may be too warm. Adjust the freezer control

to a colder setting, one position at a time, until clumps

do not form.

Dispenser is

LOCKED

• Press and hold the Lock pad for 3 seconds.

www.Hotpoint.com

Problem Possible Causes What To Do

Water has poor taste/odor

Water dispenser has not been

•Dispense water until all water in system is replenished.

(on some models)

used for a long time.

Water in first glass is

Normal when refrigerator

•Wait 24 hours for the refrigerator to completely

warm (on some models)

is first installed.

cool down.

Water dispenser has not been

•Dispense water until all water in system is replenished.

used for a long time.

Water system has been drained.

•Allow several hours for replenished supply to chill.

Water dispenser does

Water supply line turned

•See Installing the water line.

not work (on some models)

off or not connected.

Water filter clogged.

•Replace filter cartridge or remove filter and install plug.

Air may be trapped in the

•Press the dispenser arm for at least two minutes.

water system.

Dispenser is

LOCKED

• Press and hold the Lock pad for 3 seconds.

Water spurting from

Newly-installed filter cartridge.

•Run water from the dispenser for 3 minutes (about

dispenser

2 gallons).

Water is not dispensed

Water in reservoir is frozen.

• Call for service.

No water or ice cube

Supply line or shutoff

•Call a plumber.

production

valve is clogged.

Water filter clogged.

•Replace filter cartridge or remove filter and install plug.

Dispenser is

LOCKED

• Press and hold the Lock pad for 3 seconds.

Refrigerator has odor

Foods transmitting

•Foods with strong odors should be tightly wrapped.

odor to refrigerator.

•Keep an open box of baking soda in the refrigerator;

replace every three months.

Interior needs cleaning.

•See Care and cleaning.

Defrost water drainage

•See Care and cleaning.

system needs cleaning.

Moisture forms on

Not unusual during

•Wipe surface dry.

outside of refrigerator

periods of high humidity.

Moisture collects inside

Too frequent or too

long door openings.

Interior light does

No power at outlet.

•Replace fuse or reset the breaker.

not work

Light bulb burned out.

•See Replacing the light bulbs.

Water on kitchen floor or

Drain in the bottom of

•See Care and cleaning.

on bottom of freezer

the freezer clogged.

Cubes jammed in chute.

•Poke ice through with a wooden spoon.

Hot air from bottom

Normal air flow cooling motor.

of refrigerator

In the refrigeration process,

it is normal that heat be expelled

in the area under the refrigerator.

Some floor coverings are sensitive

and will discolor at these normal

and safe temperatures.

Cubed Ice was selected

Last setting was

Crushed Ice

•A few cubes were left in the crusher from the previous

but Crushed Ice was setting. This is normal.

dispensed (

on some models)

Frequent “buzzing” sound

Icemaker power switch is in the

•Slide the power switch to the OFF position. Keeping it

position but the water supply

in the ON position will damage the water valve.

to the refrigerator has not been

connected.

Before you call for service…

TERMS AND CONDITIONS:

This warranty applies only for single family domestic use in

Canada when the Refrigerator has been properly installed

according to the instructions supplied by Mabe and is

connected to an adequate and proper utility service.

Damage due to abuse, accident, commercial use, and alteration

or defacing of the serial plate cancels all obligations of this

warranty.

Service during this warranty period must be performed by an

Authorized Mabe Service Agent.

Neither Mabe nor the Dealer is liable for any claims or

damages resulting from failure of the Refrigerator or from

service delays beyond their reasonable control.

To obtain warranty service, purchaser must present the original

Bill of Sale. Components repaired or replaced are warranted

through the remainder of the original warranty period only.

This warranty is extended to the original purchaser and any

succeeding owner for products purchased for home use within

Canada. In home warranty service will be provided in areas

where it is available and deemed reasonable by Mabe

to provide.

This warranty is in addition to any statutory warranty.

WHAT IS NOT COVERED:

• Owner is responsible to pay for service calls related to

product installation and/or teaching how to use the product.

• Damage to finish must be reported within 48 hours following

the delivery of the appliance.

• Damage to finish after delivery.

• Improper installation—proper installation includes adequate

air circulation to the refrigeration system, adequate electrical,

plumbing and other connecting facilities.

• Replacement of house fuses or resetting of circuit breakers.

• Replacement of light bulbs.

• Damage to product caused by accident, fire, floods or acts

of God.

• Loss of food due to spoilage.

• Proper use and care of product as listed in the owner’s

manual, proper setting of controls.

• Product not accessible to provide required service.

• Damage caused by a non-GE brand water filter.

• WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL

DAMAGES.

IMPORTANT

Keep this warranty and your bill of sale as proof of original purchase and purchase date.

Please have serial number and model number available when calling for service.

Mabe Service is available coast to coast. If further help is

needed concerning this warranty, contact:

Manager, Consumer Relations

Mabe Canada Inc., Consumer Service

1 Factory Lane, Suite 310

Moncton, New Brunswick E1C 9M3

1.800.561.3344

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

What is covered How Long Warranted Parts Labour

(From Date of Sale) Repair or Replace

at Mabe’s Option

Compressor GE Profile: Ten (10) Years GE Profile: Ten (10) Years GE Profile: Five (5) Years

GE and All Other GE and All Other GE and All Other

Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year

Sealed System (including GE Profile: Five (5) Years GE Profile: Five (5) Years GE Profile: Five (5) Years

evaporator, condenser GE and All Other GE and All Other GE and All Other

tubing and refrigerant) Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year

All Other Parts One (1) Year One (1) Year One (1) Year

CUSTOMER WARRANTY

(for customers in Canada)

Your refrigerator is warranted to be free of defects in material and workmanship.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any

implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the

shortest period allowed by law.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available,

you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service

location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

Refrigerator Warranty. (For customers in the United States)

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

technician. To schedule service,

on-line, visit us at www.Hotpoint.com, or call 800.GE.CARES

(800.432.2737). Please have serial number and model number

available when calling for service.

For The Period Of: We Will Replace:

One Year Any part of the refrigerator which fails due to a defect in materials or workmanship.

From the date of the During this limited one-year warranty, we will also provide, free of charge, all labor and

original purchase related service to replace the defective part.

Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or workmanship.

(Water filter, if included) During this limited thirty-day warranty, we will also provide, free of charge, a replacement water

From the original filter cartridge.

purchase date of

the refrigerator



Service trips to your home to teach you how to use

the product.



Improper installation, delivery or maintenance.



Failure of the product if it is abused, misused, or used for other

than the intended purpose or used commercially.



Loss of food due to spoilage.



Replacement of house fuses or resetting of circuit breakers.



Damage caused after delivery.



Replacement of the water filter cartridge, if included, due to

water pressure that is outside the specified operating range or

due to excessive sediment in the

water supply.



Replacement of the light bulbs, if included, or water filter

cartridge, if included, other than as noted above.



Damage to the product caused by accident, fire, floods

or acts of God.



Incidental or consequential damage caused by possible defects

with this appliance.



Product not accessible to provide required service.



Damage caused by a non-GE brand water filter.

What Is Not Covered:

Staple your receipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited

Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,

are limited to one year or the shortest period allowed by law.

Performance Data Sheet

SmartWater Filtration System-GE

MWF Cartridge

This system has been tested and certi¿ed in ¿lter model GE MWF according to NSF/ANSI Standards 42 and 53 for reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water

leaving the system, as speci¿ed in NSF/ANSI Standards 42 and 53.* (Safety factors built in for unmetered usage)

Standard No. 42: Aesthetic effects

Substance

Reduction Average Inﬂuent

NSF Speciﬁed Challenge

Concentration

Average %

Reduction

Average Product

Water Concentration

Max Permissible Product

Water Concentration

NSF Reduction

Requirements

NSF Test

Report

Chlorine Taste

& Odor

2.0 mg/L 2.0mg/L ± 10% 97.5% 0.05 mg/L N/A ≥50% J-00077703

Nominal Particulate

Class I, ≥0.5 to <1.0 μm

7,833,333 pts/mL At least 10,000 particles/mL 99.7% 18,617 pts/mL N/A ≥85% J-00077704

Standard No. 53: Health effects

Substance

Reduction Average Inﬂuent

NSF Speciﬁed Challenge

Concentration

Average %

Reduction

Average Product

Water Concentration

Max Permissible Product

Water Concentration

NSF Reduction

Requirements

NSF Test

Report

Cyst* 147,5000 cysts/L Minimum 50,000 cysts/L 99.99% 1 cyst/L N/A ≥99.95% J-00077721

Asbestos 47 MF/L 10

to 10

ﬁbers/L; ﬁbers

greater than 10 μm in length

>99% <1 MF/L N/A ≥99% J-00077707

Atrazine 0.009 mg/L 0.009 mg/L ± 10% 94.5% 0.0005 mg/L 0.003 mg/L N/A J-00077708

Benzene 0.016 mg/L 0.015 mg/L ± 10% 96.7% 0.0005 mg/L 0.005 mg/L N/A J-00077717

Carbofuran 0.08 mg/L 0.08 mg/L ± 10% 98.7% 0.001 mg/L 0.04 mg/L N/A J-00077718

Endrin 0.006 mg/L 0.006 mg/L ± 10% 95.6% 0.0003 mg/L 0.002 mg/L N/A J-00082185

Lead @ pH 6.5 0.152 mg/L 0.15 mg/L ± 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00077722

Lead @ pH 8.5 0.148 mg/L 0.15 mg/L ± 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00077723

Lindane 0.002 mg/L 0.002 mg/L ± 10% 99% 0.00002 mg/L 0.0002 mg/L N/A J-00077726

Mercury @ pH 6.5 0.0058 mg/L 0.006 mg/L ± 10% 93.2% 0.0004 mg/L 0.002 mg/L N/A J-00077727

Mercury @ pH 8.5 0.0061 mg/L 0.006 mg/L ± 10% 93.2% 0.0004 mg/L 0.002 mg/L N/A J-00077728

P-Dichlorobenzene 0.222 mg/L 0.225 mg/L ± 10% 99.7% 0.005 mg/L 0.075 mg/L N/A J-00077729

Tetrachloroethylene 0.015 mg/L 0.015 mg/L ± 10% 96.6% 0.0005 mg/L 0.005 mg/L N/A J-00082184

Toxaphene 0.015 mg/L 0.015 mg/L ± 10% 93.2% 0.001 mg/L 0.003 mg/L N/A J-00077730

2, 4-D 0.218 mg/L 0.210 mg/L ± 10% 99.5% 0.0009 mg/L 0.07 mg/L N/A J-00077705

*Based on the use of Cryptosporidium parvum oocysts

Capacity 300 gallons (1,135 liters). Contaminant reduction determined by NSF testing.

It is essential that the manufacturer's recommended installation, maintenance and ﬁlter replacement requirements be carried out for the product to perform as advertised.

See Installation Manual for Warranty information.

Application Guidelines/Water Supply Parameters

Service Flow 0.5 gpm (1.9 lpm)

Water Supply Potable Water

Water Pressure 40–120 psi (2.8–8.2 bar)

Water Temperature 33ºF–100ºF (0.6ºC–38ºC)

Operating Speci¿cations

 Pressure requirement: 40–120 psi (2.8–8.2 bar), non-shock

 Temperature: 33–100°F (0.6–38°C)

 Flow rate: 0.5 gpm (1.9 lpm)

General Installation/Operation/Maintenance Requirements



trapped air.



expected to drop below 33°F (1°C). Do not install systems in areas where

ambient temperatures may go above 100ºF or below 40°F. Do not install

on a hot water supply.

Special Notices

 Installation instructions are included with the product when shipped.

 This drinking water system must be maintained according to manufacturer’s

instructions, including replacement of ¿lter cartridges.

 Do not use with water that is microbiologically unsafe or of unknown quality

without adequate disinfection before or after the system. Systems certi¿ed for

cyst reduction may be used on disinfected water that may contain ¿lterable cysts.

Standard No. 42: Aesthetic Effects

 Chemical

– Chlorine Taste and Odor

Tested and Certi¿ed by NSF International against ANSI/NSF Standards 42 and 53 in model GE MWF for the reduction of:

 Mechanical Filtration

– Particulate Reduction, Class I

Standard No. 53: Health Effects

 Chemical Reduction

– Atrazine Reduction

– Endrin Reduction

– Benzene and Carbofuran Reduction

– 1,4 Dichlorobenzene and

2,4-D Reduction

– Lead and Lindane Reduction

– Mercury and Toxaphene Reduction

 Mechanical Filtration

– Cyst and Asbestos Reduction

 The contaminants or other substances removed or reduced by this water

treatment system are not necessarily in your water.

 Check for compliance with the applicable state and local laws and regulations.

 Note that while the testing was performed under standard laboratory conditions,

actual performance may vary. Systems must be installed and operated in

accordance with manufacturer’s recommended procedures and guidelines.

 Installation and use MUST comply with all state and local plumbing codes. Do not

install if water pressure exceeds 120 psi. If your water pressure exceeds 80 psi

(552 kPa), you should install a pressure-limiting valve. Contact a plumbing

professional if you are uncertain how to check your water pressure.

 Do not install where water hammer conditions may occur. If water hammer

conditions exist you must install a water hammer arrester. Contact a plumbing

professional if you are uncertain how to check for this condition.



controlling pressure due to thermal expansion must be installed.

Appliances

Appliance Park

Louisville, KY 40225

geapplianceparts.com

REPLACEMENT

ELEMENT

State of California

Department of Public Health

Water Treatment Device

Certificate Number

Date Issued: February 2, 2010

Trademark/Model Designation

Replacement Elements

169805

GE MWF

MWF

Manufacturer:

General Electric Company

The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section

116830 of the Health and Safety Code for the following health related contaminants:

Cysts Asbestos

Lead

Mercury

Atrazine

Benzene

Carbofuran

Endrin

Lindane

Tetrachloroethylene

Toxaphene

1,4-dichlorobenzene

2, 4-D

Microbiological Contaminants and Turbidity

Inorganic/Radiological Contaminants

Organic Contaminants

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified

for cyst reduction may be used on disinfected waters that may contain filterable cysts.

300 gal

Rated Service Capacity:

0.5 gpm

Rated Service Flow:

Conditions of Certification:

La page charge ...

GE HSM25GFBSA Le manuel du propriétaire

Marque: GE

Modèle: HSM25GFBSA

Catégorie: Frigos

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: GE HSM25GFBSA Owner's manual
español: GE HSM25GFBSA El manual del propietario

GE HSM25GFBSA Le manuel du propriétaire

Ce manuel convient également à

GE HSM25GFBSA Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents