Hotpoint HSH25GFBBB Le manuel du propriétaire
- Catégorie
- Frigos
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
Hotpoint.com
Refrigerators
Side by Side
162D6746P013 39-60516-2 09-10 GE
Write your model and serial numbers here:
Model # _____________________
Serial # _____________________
Find these numbers on a label inside the
refrigerator compartment at the top on the
right side behind the controls.
Réfrigérateurs
Côte à côte
Manuel d’utilisation
et d’installation
La section française commence à la page 23
Safety Information
Connect Electricity . . . . . . . . . . . . . . .3
Extension Cords . . . . . . . . . . . . . . . . .2
Proper Disposal . . . . . . . . . . . . . . . . .2
Safety Precautions . . . . . . . . . . . . . . .2
Operating Instructions
Automatic Icemaker . . . . . . . . . . . .7–8
Controls . . . . . . . . . . . . . . . . . . . . . . .6
Crispers and Pans . . . . . . . . . . . . . . . .5
How to Install Features . . . . . . . . . . . .4
Ice and Water Dispenser . . . . . . . . . .8
Shelves and Bins . . . . . . . . . . . . . . . . .4
Water Filter Cartridge . . . . . . . . . . . .7
Care and Cleaning
Cleaning . . . . . . . . . . . . . . . . . . . . . . .9
Light Bulbs . . . . . . . . . . . . . . . . . . . .9
Installation Instructions
Preparing to Install . . . . . . . . . . . . .10
Water Line Installation . . . . . . . .11–13
Troubleshooting Tips
Before You Call
For Service . . . . . . . . . . . . . . . . .14–16
Normal Operating Sounds . . . . . . . .14
Consumer Support
Consumer Support . . . . . .Back Cover
Performance Data Sheet . . . . . . . . .19
Product Registration
(Canadian) . . . . . . . . . . . . . . . . .21, 22
Product Registration
(U.S.) . . . . . . . . . . . . . . . . . . . . . .20, 21
State of California Water
Treatment Device Certificate . . . . . .19
Warranty (Canadian) . . . . . . . . . . . .17
Warranty (U.S.) . . . . . . . . . . . . . . . . .18
Refrigeradores
Lado a lado
Models 20, 22, 25
Owner’s Manual and
Installation Instructions
Manual del propietario e
instalación
La sección en español empieza en la página 42
Refrigerators
Side by Side
Mesures de sécurité
Comment vous débarrasser
convenablement de votre
ancien réfrigérateur . . . . . . . . . . . . . . . . . . .23
Cordons prolongateurs . . . . . . . . . . . . . . . .23
Mesures de sécurité . . . . . . . . . . . . . . . . . . .23
Raccordement électrique . . . . . . . . . . . . . .24
Fonctionnement
Bacs à légumes . . . . . . . . . . . . . . . . . . . . . . .26
Cartouche du filtre à eau . . . . . . . . . . . . . . .28
Clayettes et bacs . . . . . . . . . . . . . . . . . . . . . .25
Installation des accessoires . . . . . . . . . . . . . .25
Le distributeur d’eau et de glaçons . . . . . . . .29
Les commandes . . . . . . . . . . . . . . . . . . . . . .27
Machine à glaçons automatique . . . . . . . .28–29
Entretien et nettoyage
Nettoyage . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Remplacement des ampoules . . . . . . . . . . .30
Installation
Installation de la
conduite d’eau . . . . . . . . . . . . . . . . . . . .32–34
Préparation . . . . . . . . . . . . . . . . . . . . . . . . . .31
Conseils de dépannage
Avant d’appeler un réparateur . . . . . . . .35–38
Bruits de fonctionnement
normaux . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Service à la clientèle
Feuillet de données relatives à la
performance de la
cartouche HWF . . . . . . . . . . . . . . . . . . . . . .40
Garantie pour la
clientèle au Canada . . . . . . . . . . . . . . . . . . .39
Service à la clientèle . . . . . . . . . . . . . . . . . . .41
Información de seguridad
Cables de extensión . . . . . . . . . . . . . . . . . . . 42
Conectar la electricidad. . . . . . . . . . . . . . . . 43
Deshacerse debidamente
de su refrigerador. . . . . . . . . . . . . . . . . . . . . 42
Precauciones de seguridad . . . . . . . . . . . . . 42
Instrucciones de operación
Cartucho del filtro de agua . . . . . . . . . . . . . 47
Controles del refrigerador . . . . . . . . . . . . . . 46
Dispensador . . . . . . . . . . . . . . . . . . . . . . . . . 48
Dispositivo automático
para hacer hielo . . . . . . . . . . . . . . . . . . . 47–48
Entrepaños y recipientes . . . . . . . . . . . 44–45
Gavetas de almacenamiento . . . . . . . . . . . . 45
Instalación de las características . . . . . . . . . 44
Cuidado y limpieza
Limpieza. . . . . . . . . . . . . . . . . . . . . . . . . 49–50
Reemplazo de bombillas. . . . . . . . . . . . . . . 50
Instrucciones de instalación
Instalación de la línea
de agua . . . . . . . . . . . . . . . . . . . . . . . . . . 53–56
Preparación para
instalar el refrigerador . . . . . . . . . . . . . . 51–52
Solucionar problemas
Antes de solicitar un servicio . . . . . . . . 57–60
Sonidos normales
de la operación. . . . . . . . . . . . . . . . . . . . . . . 57
Servicio al consumidor
Garantía para consumidores
en los Estados Unidos . . . . . . . . . . . . . . . . . 61
Hoja de datos de
funcionamiento . . . . . . . . . . . . . . . . . . . . . . 62
Servicio al consumidor . . . . . . . . . . . . . . . . 63
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigerators are still
dangerous…even if they will sit for “just a few days.” If
you are getting rid of your old refrigerator, please follow
the instructions below to help prevent accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
Take off the doors.
Leave the shelves in place so that children may not
easily climb inside.
Refrigerants
All refrigeration products contain refrigerants, which
under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the company
handling the disposal about what to do.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend
against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a
CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet
and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could damage
the refrigerator and seriously injure themselves.
Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet. Skin may
stick to these extremely cold surfaces.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
NOTE: Turning the refrigerator off via the controls on
the touch panel does not shut off electrical power to
the refrigerator.
Do not refreeze frozen foods which have thawed
completely.
In refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating element that
releases the cubes. Do not place fingers or hands on
the automatic icemaking mechanism while the
refrigerator is plugged in.
Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
Unplug the refrigerator before cleaning and making
repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
3
www.Hotpoint.com
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For
personal safety, this appliance must
be properly grounded.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock
hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is
properly grounded.
If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong wall outlet.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
INSURE PROPER GROUND EXISTS
BEFORE USE
The refrigerator should always be plugged into its own
individual electrical outlet which has a voltage rating that
matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a fire
hazard from overheated wires.
Never unplug your refrigerator by pulling on the power cord.
Always grip plug firmly and pull straight out from the outlet.
Repair or replace immediately all power cords that have
become frayed or otherwise damaged. Do not use a cord that
shows cracks or abrasion damage along its length or at either
end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
4
How to install features. (Not all features are on all models.)
Top Freezer Shelf
➀ TOP FREEZER SHELF
Make sure the shelf front locks into
position.
Lower Door Bin
➅ LOWER FIXED DOOR BINS
Make sure the bin fronts lock into position.
➄ ADJUSTABLE
DOOR BINS
DOOR BIN SNUGGERS
➂ DAIRY COVER
➃ BOTTLE RETAINER
Door
Shelf Front
Door
Shelf
➁ FILTER CARTRIDGE
➆
FREEZER DOOR SHELF FRONTS
Make sure that the shelf front locks
into position.
NOTE: On dispenser models, the
longer shelf fronts go in the top
two positions.
Remove Bypass Plug Install Filter Cartridge
To remove: Lift the front
of the bin up, then pull
out.
To replace or relocate:
Engage the bin in the
molded supports of the
door, and push in. Bin
will lock in place.
To remove: Lift the shelf extender
straight up, then pull out.
To replace: Engage the shelf
extender in the molded supports of
the door and push in. It will lock in
place.
About the shelves and bins. (Not all features are on all models.)
Rearranging the Shelves
To Remove
To Replace
Refrigerator Shelves:
Lift up and out
Tilt up
Insert
top hook
Lower to
lock in
place
To Remove
Freezer Shelves:
To Remove
Freezer Pan:
Remove the pan by pulling it
forward, lifting up the front and
sliding it past the stop location.
5
Slide-Out Spillproof Shelf
(on some models)
The slide-out spillproof shelf allows you to
reach items stored behind others. The special
edges are designed to help prevent spills from
dripping to lower shelves.
NOTE: Make sure you push the shelves all the
way back in before you close the door.
Spillproof Shelves (on some models)
Spillproof shelves have special edges
to help prevent spills from dripping to
lower shelves.
www.Hotpoint.com
About the crispers and pans. (Not all features are on all models.)
Adjustable Humidity Crispers and Snack Pan (on some models)
Slide the control all the way to the
High setting to provide high humidity
recommended for most vegetables.
Slide the control all the way to the Low setting
to provide lower humidity levels recommended
for most fruits.
LOW
HIGH
LOW
HIGH
Convertible Meat Pan (on some models)
The convertible meat pan has its own cold air
duct to allow a stream of cold air from the
freezer compartment to flow around
the pan.
The variable temperature control regulates the air
flow from the freezer compartment.
Set control lever up to convert the pan
to normal refrigerator temperature and provide
extra vegetable storage space. Cold air duct is
turned off. Variable settings between these
extremes can be selected.
Set control lever down to the coldest setting to
store fresh meats. If lever is left in meat position
for a long period of time, some frost may form
on the inside of the pan.
Normal
Coldest
Crisper Removal
Crispers can easily be removed by tilting up
slightly and pulling past stop location.
If the door prevents you from taking out
the crispers, the refrigerator will need to
be rolled forward until the door opens enough
to slide the crispers out. In some cases, when
you roll the refrigerator out, you will need to
move the refrigerator to
the left as you roll it out.
When replacing the crispers, make
sure you slide them through the
crisper guides.
6
About the controls on the refrigerator.
9 IS COLDES
T
0 IS OFF
5
8
9
4
3
2
1
0
6
7
5
8
9
4
3
2
1
6
7
9 IS COLDEST
0 IS OFF
FREEZER FRESH FOOD
5
8
9
4
3
2
1
0
6
7
5
8
9
4
3
2
1
6
7
Your controls will look like one of the following:
Startup Steps for Proper Temperature Control
STEP 1—Set Fresh Food Control on “5.”
STEP 2—Set Freezer Control on “5.”
STEP 3—WAIT 12 HOURS for temperature to stabilize.
STEP 4—If a change is needed, move the control one number at a time and allow 12 hours for
temperature to stabilize.
NOTE: Turning the refrigerator to the
0
(off) setting via the controls does not shut off electrical
power to the refrigerator.
Control settings will vary based on personal preferences, usage and operating
conditions and may require more than one adjustment.
0 IS OFF
9 IS COLDEST
FREEZER
REFRIGERATOR
To Change Temperature Control Setting with Touch Pads:
• Freezer setting is on the left side of the display.
• Refrigerator setting is on the right side of the display.
— Press the Warmer or Colder pad for compartment and direction desired.
— Present control setting number will illuminate.
— Each time the pad is touched, compartment setting changes one number.
A display of 1 is warmest and 9 is the coldest setting.
To Turn Cooling Off:
To stop cooling in the refrigerator and freezer compartments, first repeatedly press
the Warmer pad for the freezer until its display continuously flashes “1”. Then, using
the refrigerator control, repeatedly press Warmer until both displays flash “0”. “0” in both displays
turns off the cooling system. On some models, it may be necessary to set only
one control to
0
to turn off cooling in both compartments.
NOTE: Turning the refrigerator to the
0
(off) setting via the controls does not shut off electrical
power to the refrigerator.
Control settings will vary based on personal preferences, usage and operating
conditions and may require more than one adjustment.
About the water filter cartridge. (On some models.) www.Hotpoint.com
Water Filter Cartridge
The water filter cartridge is located in the back upper right
corner of the refrigerator compartment.
When to Replace the Filter on Models With a
Replacement Indicator Light
There is a replacement indicator light for the water filter
cartridge on the dispenser. This light will turn orange to tell you
that you need to replace the filter soon.
The filter cartridge should be replaced when the replacement
indicator light turns red or if the flow of water to the dispenser or
icemaker decreases.
When to Replace the Filter on Models Without a
Replacement Indicator Light
The filter cartridge should be replaced every six months
or earlier if the flow of water to the water dispenser or icemaker
decreases.
Removing the Filter Cartridge
If you are replacing the cartridge, first remove the old one by
slowly turning it to the left. Do not pull down on the cartridge. A
small amount of water may drip down.
Installing the Filter Cartridge
If you are replacing a
SmartWater cartridge
with an adapter, it must
be removed before
installing the cartridge.
To remove the adapter,
turn it to the left about
1/4 turn.
If you are replacing a
Water by Culligan cartridge,
leave the adapter in place.
This adapter will stay in the refrigerator when you replace
future cartridges.
On models without a replacement indicator light,
apply the month and year sticker to the new cartridge to
remind you to replace the filter in six months.
Fill the replacement cartridge with water from the tap to
allow for better flow from the dispenser immediately after
installation.
Line up the arrow on the cartridge and the cartridge holder.
Place the top of the new cartridge up inside the holder. Do
not push it up into the holder.
Slowly turn it to the right until
the filter cartridge stops. DO
NOT OVERTIGHTEN. As you turn
the cartridge, it will
automatically raise itself into
position. The cartridge will
move about 1/2 turn.
R
un water from the dispenser
for 1-1/2 gallons (about three
minutes) to clear the system and prevent sputtering.
Press and hold the RESET WATER FILTER pad (on
some models) on the dispenser for three seconds.
Filter Bypass Plug
You must use the filter bypass plug when a replacement filter
cartridge is not available. The dispenser and the icemaker will not
operate without the filter or filter bypass plug.
To use the filter bypass plug on Water by Culliganmodels, you must first remove
the filter adapter from the cartridge holder by turning it to the left.
For the maximum benefit of your filtration system, GE
recommends the use of GE branded SmartWater filters only.
Using GE branded filters in GE and Hotpoint refrigerators
provides optimal performance and reliability. GE branded
SmartWater filters are always the right choice because they are
patented and designed specifically for GE products. GE
SmartWater filters meet rigorous industry NSF standards for
safety and quality that are important for products that are
filtering your water. GE has not qualified non-GE branded filters
for use in GE and Hotpoint refrigerators and there is no
assurance that non-GE branded filters meet GE’s standards for
quality, performance and reliability.
If you have questions—visit our Website
at www.hotpoint.com,
or call 1.800.GE.CARES (1.800.432.2737).
Replacement filters:
To order additional filter cartridges in the United States,
visit our Website at www.hotpoint.com, or call GE Parts and
Accessories, 800.626.2002.
MWF
Suggested Retail $38.95–47.95
Customers in Canada should consult the yellow pages for the
nearest Mabe Service Center.
Customers outside of the United States or Canada should
contact the local distributor.
Cartridge
Holder
Filter
Bypass
Plug
Filter
Bypass
Plug
SmartWater
Water by Culligan
(appearance may vary)
With adapter
Without adapter
About the automatic icemaker.
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Icemaker
Feeler Arm
Power Switch
Automatic Icemaker(on some models)
When the refrigerator has been connected to
the water supply, slide the power switch to the
ON position.
The icemaker will fill with water when
it cools to 15°F. When the bin fills to the level
of the feeler arm, the icemaker will stop
producing ice.
Be sure nothing interferes with the sweep of the
feeler arm.
Throw away the first few batches of ice to allow
the water line to clear.
The icemaker will produce seven cubes per
cycle—approximately 100–130 cubes in a 24-
hour period, depending on freezer
compartment temperature, room
temperature, number of door openings and
other use conditions.
You will hear a buzzing sound each time the
icemaker fills with water.
7
About the automatic icemaker.
It is normal for several cubes to be joined together.
If ice is not used frequently, old ice cubes will become
cloudy, taste stale, and shrink.
Icemaker Accessory Kit
If your refrigerator did not come already equipped
with an automatic icemaker, an icemaker accessory kit
is available at extra cost. Check the back of the
refrigerator for the specific icemaker kit needed for
your model.
Select or
Press the glass gently against the top of the
dispenser cradle.
The spill shelf is not self-draining. To reduce
water spotting, the shelf and its grille should be
cleaned regularly.
Locking the Dispenser (on some models)
Press the Lock pad
for 3 seconds to lock the
dispenser and control panel. To
unlock, press and hold
the pad again for 3 seconds.
If no water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser arm for at least two
minutes to remove trapped air from the water line
and to fill the water system. To flush out impurities
in the water line, throw away the first six glassfuls
of water.
CAUTION: Never put fingers or any other
objects into the ice crusher discharge opening.
Dispenser Light
This pad turns the night light in
the dispenser on and off. The
light also comes on when the
dispenser cradle is pressed. If this
light burns out, it should be
replaced with a 6 watt maximum,
12 volt DC bulb.
About the ice and water dispenser. (On some models.)
To Use the Dispenser
Important Facts About Your Dispenser
Do not add ice from trays or bags to the storage bin. It may
not crush or dispense well.
Avoid overfilling glass with ice and use of narrow glasses.
Backed-up ice can jam the chute or cause the door in the
chute to freeze shut. If ice is blocking the chute, poke it
through with a wooden spoon.
Beverages and foods should not be quick-chilled in the ice
storage bin. Cans, bottles or food packages in the storage bin
may cause the icemaker or auger to jam.
To keep dispensed ice from missing the glass, put the glass
close to, but not touching, the dispenser opening.
Some crushed ice may be dispensed even though you selected
Cubed. This happens occasionally when a few cubes have been
left in the crusher.
After crushed ice is dispensed, some water may drip from the
chute.
Sometimes a small mound of snow will form on the door in
the ice chute. This condition is normal and usually occurs
when you have dispensed crushed ice repeatedly. The snow
will eventually evaporate.
The first glass of water dispensed may be warmer than the
following ones. This is normal.
Dispensed water is not ice cold. For colder water, simply add
crushed ice or cubes before dispensing water.
Ice Storage Drawer on Dispenser Models
To remove:
Slide the icemaker power switch to the OFF position. Pull
the drawer straight out and then lift past the stop position.
To replace:
When replacing the drawer, make sure to push it firmly
into place. If it does not go all the way back, remove it and
rotate the drive mechanism 1/4 turn. Then push the
drawer back again.
Drive
Mechanism
Rotate
Spill Shelf
8
Care and cleaning of the refrigerator. www.Hotpoint.com
Cleaning the Outside
The dispenser drip area, (on some models)
beneath the grille, should be wiped dry. Water left
in this area may leave deposits. Remove the
deposits by adding undiluted vinegar to the
well. Soak until the deposits disappear or
become loose enough to rinse away.
The dispenser cradle (on some models). Before
cleaning, lock the dispenser by pressing and
holding the Lock pad for
3 seconds. Clean with warm water and baking
soda solution—about a tablespoon (15 ml) of
baking soda to a quart (1 l)
of water. Rinse thoroughly and wipe dry.
The door handles and trim. Clean with a
cloth dampened with soapy water. Dry
with a soft cloth.
Keep the outside clean. Wipe with a clean cloth
lightly dampened with kitchen appliance wax or
mild liquid dish detergent. Dry and polish with
a clean, soft cloth.
Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box of
baking soda in the refrigerator and freezer
compartments.
Unplug the refrigerator before cleaning. If this is
not practical, wring excess moisture out of
sponge or cloth when cleaning around switches,
lights or controls.
Use warm water and baking soda solution—
about a tablespoon (15 ml) of baking soda to a
quart (1 l) of water. This both cleans and
neutralizes odors. Rinse and wipe dry.
After cleaning the door gaskets, apply a thin
layer of petroleum jelly to the door gaskets at
the hinge side. This helps keep the gaskets from
sticking and bending out
of shape.
Drain opening in freezer compartment.
During yearly cleaning, remove bottom freezer
pan and flush a solution of baking soda—1
teaspoon (5 ml) and 2 cups (500 ml) of hot (not
boiling) water— through the drain line with the
help of a meat baster. This will help eliminate
odor and reduce the likelihood of a clogged
drain line. If drain becomes clogged, use a
meat baster and baking soda solution to force
the clog through the drain line.
Avoid cleaning cold glass shelves with hot water
because the extreme temperature difference may
cause them to break. Handle glass shelves carefully.
Bumping tempered glass can cause it to shatter.
Do not wash any plastic refrigerator parts in the
dishwasher.
For long vacations or absences, remove food and unplug the
refrigerator. Clean the interior with a baking soda solution of
one tablespoon (15 ml) of baking soda to one quart (1 l) of water.
Leave the doors open.
Slide the icemaker power switch to the OFF position and shut off
the water supply to the refrigerator.
Behind the Refrigerator
Be careful when moving the refrigerator away from the wall. All
types of floor coverings can be damaged, particularly cushioned
coverings and those with embossed surfaces.
Pull the refrigerator straight out and return it to position by
pushing it straight in. Moving the refrigerator in a side direction
may result in damage to the floor covering or refrigerator.
When pushing the refrigerator back, make sure you don’t roll over
the power cord or icemaker supply line (on some models).
Preparing for Vacation
Preparing to Move
Secure all loose items such as grille, shelves and drawers by taping them securely in place to prevent damage.
Be sure the refrigerator stays in an upright position during moving.
NOTE: Turning the refrigerator to the 0 (off) setting via the controls does not shut off electrical power to the refrigerator.
Replacing the Light Bulbs
Unplug the refrigerator.
Remove the shelf just below the light shield.
Replace with an appliance bulb of the same
or lower wattage.
Reinstall the shelf and plug the refrigerator
back in.
9
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT
–
Save these instructions
for local inspector’s use.
•
IMPORTANT
–
Observe all governing
codes and ordinances.
•
Note to Installer
–
Be sure to leave these
instructions with the Consumer.
•
Note to Consumer
–
Keep these instructions for
future reference.
•
Skill level
– Installation of this appliance requires basic
mechanical skills.
•
Completion time
– Refrigerator Installation
15 minutes
• Proper installation is the responsibility of installer.
• Product failure due to improper installation is not
covered under the Warranty.
REFRIGERATOR LOCATION
• Do not install the refrigerator where the temperature will
go below 60°F (16°C) because it will not run often enough
to maintain proper temperatures.
• Install it on a floor strong enough to support it fully
loaded.
Installation Instructions
Models 20, 22, 25
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical connections.
•
Sides
1/8”(4 mm) •
Top
1” (25 mm) •
Back
1” (25 mm)
A door clearance of 3/4” (19 mm) is needed for a 90º door
opening which provides better access to food storage area.
CLEARANCES
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. A GE water supply kit is
available at extra cost from your dealer, by visiting our
Website at
www.Hotpoint.com
(in Canada, at
www.geappliances.ca
), or from Parts and Accessories,
800.626.2002.
WATER SUPPLY TO THE ICEMAKER (on
some models)
Questions? Call 800.GE.CARES (800.432.2737)
or
Visit our Website at: www.Hotpoint.com
Questions? In Canada, call 1.800.561.3344
or
Visit our Website at: www.geappliances.ca
10
The rollers have 3 purposes:
Rollers adjust so the door closes easily when opened about
halfway.
Rollers adjust so the refrigerator is firmly positioned on the
floor and does not wobble.
Rollers allow you to move the refrigerator away from the
wall for cleaning.
To adjust the rollers,
remove the base grille by pulling it out at
the bottom.
Turn the roller adjusting screws
clockwise to raise
the
refrigerator,
counterclockwise to lower
it. Use an adjustable
wrench (3/8”hex head bolt) or pliers.
To replace base grille,
line up the clips on back of grille
between the bar and the bottom of the cabinet. Push forward
until grille snaps into place.
ROLLERS
To remove the base
grille, open the doors
and then pull the
grille straight out.
5/16”Socket
Wrench
Raise
DOOR ALIGNMENT
After leveling, make sure that doors are even at the top.
To make the doors even,
adjust the refrigerator door.
Using a 5/16” socket wrench, turn the door adjusting screw
to the right to raise the door, to the left to lower it. (A nylon
plug, embedded in the threads of the pin, prevents the pin
from turning unless a wrench is used.)
After one or two turns of the wrench, open and close the
refrigerator compartment door and check the alignment at
the top of the doors.
Installation Instructions
11
INSTALLING THE WATER LINE
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are GE
SmartConnect
™
Refrigerator Tubing (WX08X10002,
WX08X10006, WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse Osmosis
Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water systems,
follow the manufacturer’s recommendations.
If the water supply to the refrigerator is from a Reverse
Osmosis Water Filtration System AND the refrigerator also
has a water filter, use the refrigerator’s filter bypass plug.
Using the refrigerator’s water filtration cartridge in
conjunction with the RO filter can result in hollow ice cubes
and slower water flow from the water dispenser.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive water
damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and lead to
water leakage or flooding. Call a qualified plumber to correct
water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the water line,
make sure the icemaker power switch is in the OFF position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
All installations must be in accordance with local plumbing
code requirements.
WARNING –
Connect to potable water
supply only.
BEFORE YOU BEGIN
•
Copper or GE SmartConnect
™
Refrigerator Tubing kit
,
1/4” outer diameter to connect the refrigerator to the
water supply. If using copper, be sure both ends of the
tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Be sure there is
sufficient extra tubing to allow the refrigerator to move out
from the wall after installation.
GE SmartConnect
™
Refrigerator Tubing Kits are available
in the following lengths:
2′ (0.6 m) – WX08X10002
6′ (1.8 m) – WX08X10006
15′ (4.6 m) – WX08X10015
25′ (7.6 m) – WX08X10025
WHAT YOU WILL NEED
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect™ Refrigerator Tubing kits.
Do not use any other plastic water supply line because the
line is under pressure at all times. Certain types of plastic
will crack or rupture with age and cause water damage to
your home.
•
A GE water supply kit
(containing tubing, shutoff valve
and fittings listed below) is available at extra cost from
your dealer or from Parts and Accessories,
800.626.2002.
•
A cold water supply
. The water pressure must be between
20 and 120 p.s.i. (1.4–8.2 bar) on models without a water
filter and between 40 and 120 p.s.i. (2.8–8.2 bar) on
models with a water filter.
•
Power drill.
•
1/2
”
or adjustable wrench.
•
Straight and Phillips blade screwdriver.
•
Two 1/4
”
outer diameter compression nuts and
2 ferrules (sleeves)
—to connect the copper tubing
to the shutoff valve and the refrigerator water valve.
OR
• If you are using a GE SmartConnect™ Refrigerator
Tubing kit, the necessary fittings are preassembled to the
tubing.
• If your existing copper water line has a flared fitting at
the end, you will need an
adapter
(available at plumbing
supply stores) to connect the water line to the refrigerator
OR
you can cut off the flared fitting
with a
tube cutter
and then use a compression fitting. Do
not cut formed end from GE SmartConnect™
Refrigerator tubing.
•
Shutoff valve
to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32” at the point of
connection to the
COLD WATER LINE
. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve complies
with your local plumbing codes. Install the shutoff valve
on the nearest frequently used drinking water line.
WHAT YOU WILL NEED (CONT.)
Installation Instructions
12
SHUT OFF MAIN WATER SUPPLY
1
Choose a location for the valve that is easily accessible.
It is best to connect into the side of a vertical water
pipe. When it is necessary to connect into a horizontal
water pipe, make the connection to the top or side,
rather than at the bottom,
to avoid drawing off any sediment from the
water pipe.
Drill a 1/4” hole in the water pipe (even if using a self-
piercing valve) using a sharp bit. Remove any burrs
resulting from drilling the hole in the pipe.
Take care not
to allow water to drain into the drill.
Failure to drill a
1/4” hole may result in reduced ice production or
smaller cubes.
DRILL THE HOLE FOR THE VALVE
2
Fasten the shutoff valve to the cold water pipe with the
pipe clamp.
Tighten the clamp screws until the sealing washer begins
to swell.
NOTE:
Do not overtighten or you may crush the
tubing.
NOTE:
Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts. Consult
with your licensed plumber.
FASTEN THE SHUTOFF VALVE
3
Vertical Cold
Water Pipe
Saddle-Type
Shutoff Valve
Pipe Clamp
Clamp Screw
Washer
Inlet End
Route the tubing between the cold water line and the
refrigerator.
Route the tubing through a hole drilled in the wall or
floor (behind the refrigerator or adjacent base cabinet)
as close to the wall as possible.
NOTE:
Be sure there is sufficient extra tubing
to allow the refrigerator to move out from the wall after
installation.
ROUTE THE TUBING
4
Place the compression nut and ferrule (sleeve) for copper
tubing onto the end of the tubing and connect it to the
shutoff valve.
Make sure the tubing is fully inserted into the valve.
Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then tighten one
additional turn with a wrench. Overtightening may
cause leaks.
CONNECT THE TUBING TO THE VALVE
5
Turn the main water supply on and flush out the tubing
until the water is clear.
FLUSH OUT THE TUBING
6
NOTE:
Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts. Consult
with your licensed plumber.
Saddle-Type
Shutoff Valve
Compression Nut
SmartConnect™
Tubing
Packing Nut
Outlet Valve
Ferrule (sleeve)
NOTES:
• Before making the connection to the refrigerator, be
sure the refrigerator power cord is not plugged into
the wall outlet.
• If your refrigerator does not have a water filter, we
recommend installing one if your water supply has
sand or particles that could clog the screen of the
refrigerator’s water valve. Install it in the water line
near the refrigerator. If using a GE SmartConnect™
Refrigerator Tubing kit, you
will need an additional tube (WX08X10002)
to connect the filter. Do not cut plastic tube
to install filter.
CONNECT THE TUBING TO THE
REFRIGERATOR
7
Installation Instructions
13
Place the compression nut and ferrule (sleeve) onto the
end of the tubing as shown. On a GE SmartConnect
™
Refrigerator Tubing kit, the nuts
are already assembled to the tubing.
Insert the end of the tubing into the refrigerator
connection as far as possible. While holding the tubing,
tighten the fitting.
For plastic tubing from a GE SmartConnect
™
Refrigerator Tubing kit, insert the molded end of the
tubing into the refrigerator connection and tighten the
compression nut until it is hand tight, then tighten one
additional turn with a wrench. Overtightening may
cause leaks.
Fasten the tubing into the clamp provided as shown to
keep it in position. You may need to pry open the
clamp.
One of the illustrations below will look like the
connection on your refrigerator.
On models using the refrigeration connection at the
water valve, remove the plastic flexible cap.
CONNECT THE TUBING TO THE
REFRIGERATOR
(CONT.)
7
Some models have the refrigerator connection at the
end of tubing located outside the compressor
compartment access cover. On other models, the
compressor compartment access cover must be removed
in order to access the refrigerator connection at the
water valve.
1/4”
Compression
Nut
Tubing
Clamp
1/4”
Tubing
Refrigerator
Connection
SmartConnect™
Tubing
Ferrule
(sleeve)
Tighten any connections that leak.
TURN THE WATER ON AT THE
SHUTOFF VALVE
CONNECT THE TUBING TO THE
REFRIGERATOR
(CONT.)
Reattach the access cover.
SmartConnect™
Tubing
1/4”
Compression
Nut
1/4”
Tubing
8
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the wall.
Push the refrigerator back to the wall.
PLUG IN THE REFRIGERATOR
9
START THE ICEMAKER
Slide the icemaker power switch to the ON position. The
icemaker will not begin to operate until it reaches its
operating temperature of 15°F (-9°C)
or below. It will then begin operation automatically if
the icemaker power switch is in the ON position.
10
Tubing
Clamp
Refrigerator
Connection
Ferrule
(sleeve)
7
Normal operating sounds.
The new high efficiency compressor runs faster and will have a higher pitch hum or
pulsating sound while operating.
The fan circulating air inside the freezer which keeps the temperatures throughout.
Water dropping on the defrost heater causing a sizzling, hissing or popping
sound during the defrost cycle.
The flow of refrigerant through the freezer cooling coils sounds like boiling
water or a gurgling noise.
Cracking or popping of cooling coils caused by expansion and contraction
during defrost and refrigeration following defrost.
Water dripping as it melts from the evaporator and flows to the drain pan
during the defrost cycle.
Icemaker (on some models)
The icemaker water valve will buzz when the icemaker fills with water. If the
power switch is in the ON position it will buzz even if it has not yet been hooked up to
water. Keeping the power switch in the ON position before it is hooked
up to water can damage the icemaker. To prevent this, slide the power switch to the OFF
position. This will stop the buzzing.
The sound of cubes dropping into the bin and water running in pipes as
icemaker refills.
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem Possible Causes What To Do
Refrigerator does not
Refrigerator in defrost cycle.
•Wait about 30 minutes for defrost cycle to end.
operate
Freezer control
•Move the freezer control to a lower temperature setting.
in
0 (off)
position.
Refrigerator is unplugged.
•Push the plug completely into the outlet.
The fuse is blown/circuit
•Replace fuse or reset the breaker.
breaker is tripped.
Refrigerator or freezer
Temperature control not set
•See About the controls.
compartment too warm
cold enough.
Warm weather or frequent
•Set the temperature control one step colder.
door openings.
See About the controls.
Door left open.
•Check to see if package is holding door open.
These sounds are normal and are due mostly to highly efficient operation.
14
Before you call for service…
Newer refrigerators sound different from older refrigerators. Modern refrigerators have
more features and use newer technology.
Do you hear what I hear? These sounds are normal.
Problem Possible Causes What To Do
Vibration or rattling
Front rollers need adjusting. •
See Rollers. Slight vibration is normal.
Motor operates for
Normal when refrigerator
•Wait 24 hours for the refrigerator to completely
long periods or cycles
is first plugged in.
cool down.
on and off frequently.
Often occurs when large
•This is normal.
(Modern refrigerators
amounts of food are
with more storage
placed in refrigerator.
space and a larger
Door left open.
•Check to see if package is holding door open.
freezer require more
Hot weather or frequent
•This is normal.
operating time. They
door openings.
start and stop often
Temperature controls
•See About the controls.
to maintain even
set at the coldest
temperatures.)
setting.
Frost or ice crystals
Door left open.
•Check to see if package is holding door open.
on frozen food
Too frequent or too long
(frost within package
door openings.
is normal)
Divider between
Automatic energy saver
•This helps prevent condensation on the outside.
refrigerator and freezer
system circulates warm
compartments
liquid around front edge
feels warm
of freezer compartment.
Automatic icemaker
Icemaker power switch
•Slide the power switch to the ON position.
does not work
is in the
OFF
position.
(on some models)
Water supply turned off or
•See Installing the water line.
not connected.
Freezer compartment
•Wait 24 hours for the refrigerator to completely
too warm.
cool down.
Piled up cubes in the storage
•Level cubes by hand.
bin cause icemaker to shut off.
Ice cubes stuck in icemaker.
•Turn off the icemaker, remove cubes and turn the
icemaker back on.
Ice cubes have
Ice storage bin needs cleaning.
•Empty and wash bin. Discard old cubes.
odor/taste
Food transmitting odor/taste
•Wrap foods well.
to ice cubes.
Interior of refrigerator
•See Care and cleaning.
needs cleaning.
Small or hollow cubes
Water filter clogged.
•Replace filter cartridge with new cartridge or with plug.
Slow ice cube freezing
Door left open.
•Check to see if package is holding door open.
Temperature control not set
•See About the controls.
cold enough.
Door not closing
Door gasket on hinge side
•Apply petroleum jelly on face of gasket.
properly
sticking or folding over.
Orange glow in freezer
Defrost heater is on.
•This is normal.
Cube dispenser does not
Icemaker or water supply
•Turn on icemaker or water supply.
work (on some models)
turned off.
Ice cubes are frozen to
•Remove cubes.
icemaker feeler arm.
Irregular ice clumps in
•Break up with fingertip pressure and discard
storage container.
remaining clumps.
•Freezer may be too warm. Adjust the freezer control
to a colder setting, one position at a time, until clumps
do not form.
Dispenser is
LOCKED
.
• Press and hold the Lock pad for 3 seconds.
15
www.Hotpoint.com
Problem Possible Causes What To Do
Water has poor taste/odor
Water dispenser has not been
•Dispense water until all water in system is replenished.
(on some models)
used for a long time.
Water in first glass is
Normal when refrigerator
•Wait 24 hours for the refrigerator to completely
warm (on some models)
is first installed.
cool down.
Water dispenser has not been
•Dispense water until all water in system is replenished.
used for a long time.
Water system has been drained.
•Allow several hours for replenished supply to chill.
Water dispenser does
Water supply line turned
•See Installing the water line.
not work (on some models)
off or not connected.
Water filter clogged.
•Replace filter cartridge or remove filter and install plug.
Air may be trapped in the
•Press the dispenser arm for at least two minutes.
water system.
Dispenser is
LOCKED
.
• Press and hold the Lock pad for 3 seconds.
Water spurting from
Newly-installed filter cartridge.
•Run water from the dispenser for 3 minutes (about
dispenser
1
1
2 gallons).
Water is not dispensed
Water in reservoir is frozen.
• Call for service.
No water or ice cube
Supply line or shutoff
•Call a plumber.
production
valve is clogged.
Water filter clogged.
•Replace filter cartridge or remove filter and install plug.
Dispenser is
LOCKED
.
• Press and hold the Lock pad for 3 seconds.
Refrigerator has odor
Foods transmitting
•Foods with strong odors should be tightly wrapped.
odor to refrigerator.
•Keep an open box of baking soda in the refrigerator;
replace every three months.
Interior needs cleaning.
•See Care and cleaning.
Defrost water drainage
•See Care and cleaning.
system needs cleaning.
Moisture forms on
Not unusual during
•Wipe surface dry.
outside of refrigerator
periods of high humidity.
Moisture collects inside
Too frequent or too
long door openings.
Interior light does
No power at outlet.
•Replace fuse or reset the breaker.
not work
Light bulb burned out.
•See Replacing the light bulbs.
Water on kitchen floor or
Drain in the bottom of
•See Care and cleaning.
on bottom of freezer
the freezer clogged.
Cubes jammed in chute.
•Poke ice through with a wooden spoon.
Hot air from bottom
Normal air flow cooling motor.
of refrigerator
In the refrigeration process,
it is normal that heat be expelled
in the area under the refrigerator.
Some floor coverings are sensitive
and will discolor at these normal
and safe temperatures.
Cubed Ice was selected
Last setting was
Crushed Ice
.
•A few cubes were left in the crusher from the previous
but Crushed Ice was setting. This is normal.
dispensed (
on some models)
Frequent “buzzing” sound
Icemaker power switch is in the
•Slide the power switch to the OFF position. Keeping it
ON
position but the water supply
in the ON position will damage the water valve.
to the refrigerator has not been
connected.
Before you call for service…
16
17
TERMS AND CONDITIONS:
This warranty applies only for single family domestic use in
Canada when the Refrigerator has been properly installed
according to the instructions supplied by Mabe and is
connected to an adequate and proper utility service.
Damage due to abuse, accident, commercial use, and alteration
or defacing of the serial plate cancels all obligations of this
warranty.
Service during this warranty period must be performed by an
Authorized Mabe Service Agent.
Neither Mabe nor the Dealer is liable for any claims or
damages resulting from failure of the Refrigerator or from
service delays beyond their reasonable control.
To obtain warranty service, purchaser must present the original
Bill of Sale. Components repaired or replaced are warranted
through the remainder of the original warranty period only.
This warranty is extended to the original purchaser and any
succeeding owner for products purchased for home use within
Canada. In home warranty service will be provided in areas
where it is available and deemed reasonable by Mabe
to provide.
This warranty is in addition to any statutory warranty.
WHAT IS NOT COVERED:
• Owner is responsible to pay for service calls related to
product installation and/or teaching how to use the product.
• Damage to finish must be reported within 48 hours following
the delivery of the appliance.
• Damage to finish after delivery.
• Improper installation—proper installation includes adequate
air circulation to the refrigeration system, adequate electrical,
plumbing and other connecting facilities.
• Replacement of house fuses or resetting of circuit breakers.
• Replacement of light bulbs.
• Damage to product caused by accident, fire, floods or acts
of God.
• Loss of food due to spoilage.
• Proper use and care of product as listed in the owner’s
manual, proper setting of controls.
• Product not accessible to provide required service.
• Damage caused by a non-GE brand water filter.
• WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL
DAMAGES.
IMPORTANT
Keep this warranty and your bill of sale as proof of original purchase and purchase date.
Please have serial number and model number available when calling for service.
Mabe Service is available coast to coast. If further help is
needed concerning this warranty, contact:
Manager, Consumer Relations
Mabe Canada Inc., Consumer Service
1 Factory Lane, Suite 310
Moncton, New Brunswick E1C 9M3
1.800.561.3344
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
What is covered How Long Warranted Parts Labour
(From Date of Sale) Repair or Replace
at Mabe’s Option
Compressor GE Profile: Ten (10) Years GE Profile: Ten (10) Years GE Profile: Five (5) Years
GE and All Other GE and All Other GE and All Other
Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year
Sealed System (including GE Profile: Five (5) Years GE Profile: Five (5) Years GE Profile: Five (5) Years
evaporator, condenser GE and All Other GE and All Other GE and All Other
tubing and refrigerant) Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year
All Other Parts One (1) Year One (1) Year One (1) Year
CUSTOMER WARRANTY
(for customers in Canada)
Your refrigerator is warranted to be free of defects in material and workmanship.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any
implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the
shortest period allowed by law.
18
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available,
you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service
location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
Refrigerator Warranty. (For customers in the United States)
All warranty service provided by our Factory Service Centers,
or an authorized Customer Care
®
technician. To schedule service,
on-line, visit us at www.Hotpoint.com, or call 800.GE.CARES
(800.432.2737). Please have serial number and model number
available when calling for service.
For The Period Of: We Will Replace:
One Year Any part of the refrigerator which fails due to a defect in materials or workmanship.
From the date of the During this limited one-year warranty, we will also provide, free of charge, all labor and
original purchase related service to replace the defective part.
Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or workmanship.
(Water filter, if included) During this limited thirty-day warranty, we will also provide, free of charge, a replacement water
From the original filter cartridge.
purchase date of
the refrigerator
Service trips to your home to teach you how to use
the product.
Improper installation, delivery or maintenance.
Failure of the product if it is abused, misused, or used for other
than the intended purpose or used commercially.
Loss of food due to spoilage.
Replacement of house fuses or resetting of circuit breakers.
Damage caused after delivery.
Replacement of the water filter cartridge, if included, due to
water pressure that is outside the specified operating range or
due to excessive sediment in the
water supply.
Replacement of the light bulbs, if included, or water filter
cartridge, if included, other than as noted above.
Damage to the product caused by accident, fire, floods
or acts of God.
Incidental or consequential damage caused by possible defects
with this appliance.
Product not accessible to provide required service.
Damage caused by a non-GE brand water filter.
What Is Not Covered:
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,
are limited to one year or the shortest period allowed by law.
Performance Data Sheet
SmartWater Filtration System-GE
®
MWF Cartridge
This system has been tested and certi¿ed in ¿lter model GE MWF according to NSF/ANSI Standards 42 and 53 for reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water
leaving the system, as speci¿ed in NSF/ANSI Standards 42 and 53.* (Safety factors built in for unmetered usage)
Standard No. 42: Aesthetic effects
Substance
Reduction Average Influent
NSF Specified Challenge
Concentration
Average %
Reduction
Average Product
Water Concentration
Max Permissible Product
Water Concentration
NSF Reduction
Requirements
NSF Test
Report
Chlorine Taste
& Odor
2.0 mg/L 2.0mg/L ± 10% 97.5% 0.05 mg/L N/A ≥50% J-00077703
Nominal Particulate
Class I, ≥0.5 to <1.0 μm
7,833,333 pts/mL At least 10,000 particles/mL 99.7% 18,617 pts/mL N/A ≥85% J-00077704
Standard No. 53: Health effects
Substance
Reduction Average Influent
NSF Specified Challenge
Concentration
Average %
Reduction
Average Product
Water Concentration
Max Permissible Product
Water Concentration
NSF Reduction
Requirements
NSF Test
Report
Cyst* 147,5000 cysts/L Minimum 50,000 cysts/L 99.99% 1 cyst/L N/A ≥99.95% J-00077721
Asbestos 47 MF/L 10
7
to 10
8
fibers/L; fibers
greater than 10 μm in length
>99% <1 MF/L N/A ≥99% J-00077707
Atrazine 0.009 mg/L 0.009 mg/L ± 10% 94.5% 0.0005 mg/L 0.003 mg/L N/A J-00077708
Benzene 0.016 mg/L 0.015 mg/L ± 10% 96.7% 0.0005 mg/L 0.005 mg/L N/A J-00077717
Carbofuran 0.08 mg/L 0.08 mg/L ± 10% 98.7% 0.001 mg/L 0.04 mg/L N/A J-00077718
Endrin 0.006 mg/L 0.006 mg/L ± 10% 95.6% 0.0003 mg/L 0.002 mg/L N/A J-00082185
Lead @ pH 6.5 0.152 mg/L 0.15 mg/L ± 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00077722
Lead @ pH 8.5 0.148 mg/L 0.15 mg/L ± 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00077723
Lindane 0.002 mg/L 0.002 mg/L ± 10% 99% 0.00002 mg/L 0.0002 mg/L N/A J-00077726
Mercury @ pH 6.5 0.0058 mg/L 0.006 mg/L ± 10% 93.2% 0.0004 mg/L 0.002 mg/L N/A J-00077727
Mercury @ pH 8.5 0.0061 mg/L 0.006 mg/L ± 10% 93.2% 0.0004 mg/L 0.002 mg/L N/A J-00077728
P-Dichlorobenzene 0.222 mg/L 0.225 mg/L ± 10% 99.7% 0.005 mg/L 0.075 mg/L N/A J-00077729
Tetrachloroethylene 0.015 mg/L 0.015 mg/L ± 10% 96.6% 0.0005 mg/L 0.005 mg/L N/A J-00082184
Toxaphene 0.015 mg/L 0.015 mg/L ± 10% 93.2% 0.001 mg/L 0.003 mg/L N/A J-00077730
2, 4-D 0.218 mg/L 0.210 mg/L ± 10% 99.5% 0.0009 mg/L 0.07 mg/L N/A J-00077705
*Based on the use of Cryptosporidium parvum oocysts
Capacity 300 gallons (1,135 liters). Contaminant reduction determined by NSF testing.
It is essential that the manufacturer's recommended installation, maintenance and filter replacement requirements be carried out for the product to perform as advertised.
See Installation Manual for Warranty information.
Application Guidelines/Water Supply Parameters
Service Flow 0.5 gpm (1.9 lpm)
Water Supply Potable Water
Water Pressure 40–120 psi (2.8–8.2 bar)
Water Temperature 33ºF–100ºF (0.6ºC–38ºC)
Operating Speci¿cations
Pressure requirement: 40–120 psi (2.8–8.2 bar), non-shock
Temperature: 33–100°F (0.6–38°C)
Flow rate: 0.5 gpm (1.9 lpm)
General Installation/Operation/Maintenance Requirements
trapped air.
expected to drop below 33°F (1°C). Do not install systems in areas where
ambient temperatures may go above 100ºF or below 40°F. Do not install
on a hot water supply.
Special Notices
Installation instructions are included with the product when shipped.
This drinking water system must be maintained according to manufacturer’s
instructions, including replacement of ¿lter cartridges.
Do not use with water that is microbiologically unsafe or of unknown quality
without adequate disinfection before or after the system. Systems certi¿ed for
cyst reduction may be used on disinfected water that may contain ¿lterable cysts.
Standard No. 42: Aesthetic Effects
Chemical
– Chlorine Taste and Odor
Tested and Certi¿ed by NSF International against ANSI/NSF Standards 42 and 53 in model GE MWF for the reduction of:
Mechanical Filtration
– Particulate Reduction, Class I
Standard No. 53: Health Effects
Chemical Reduction
– Atrazine Reduction
– Endrin Reduction
– Benzene and Carbofuran Reduction
– 1,4 Dichlorobenzene and
2,4-D Reduction
– Lead and Lindane Reduction
– Mercury and Toxaphene Reduction
Mechanical Filtration
– Cyst and Asbestos Reduction
The contaminants or other substances removed or reduced by this water
treatment system are not necessarily in your water.
Check for compliance with the applicable state and local laws and regulations.
Note that while the testing was performed under standard laboratory conditions,
actual performance may vary. Systems must be installed and operated in
accordance with manufacturer’s recommended procedures and guidelines.
Installation and use MUST comply with all state and local plumbing codes. Do not
install if water pressure exceeds 120 psi. If your water pressure exceeds 80 psi
(552 kPa), you should install a pressure-limiting valve. Contact a plumbing
professional if you are uncertain how to check your water pressure.
Do not install where water hammer conditions may occur. If water hammer
conditions exist you must install a water hammer arrester. Contact a plumbing
professional if you are uncertain how to check for this condition.
controlling pressure due to thermal expansion must be installed.
GE
Appliances
Appliance Park
Louisville, KY 40225
geapplianceparts.com
© 2010 GE Company PC61278B
REPLACEMENT
ELEMENT
19
State of California
Department of Public Health
Water Treatment Device
Certificate Number
Date Issued: February 2, 2010
Trademark/Model Designation
Replacement Elements
169805
-
GE MWF
MWF
Manufacturer:
General Electric Company
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section
116830 of the Health and Safety Code for the following health related contaminants:
Cysts Asbestos
Lead
Mercury
Atrazine
Benzene
Carbofuran
Endrin
Lindane
Tetrachloroethylene
Toxaphene
1,4-dichlorobenzene
2, 4-D
Microbiological Contaminants and Turbidity
Inorganic/Radiological Contaminants
Organic Contaminants
Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified
for cyst reduction may be used on disinfected waters that may contain filterable cysts.
300 gal
Rated Service Capacity:
0.5 gpm
Rated Service Flow:
Conditions of Certification:
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
Hotpoint HSH25GFBBB Le manuel du propriétaire
- Catégorie
- Frigos
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
GE HSS25GFPWW Le manuel du propriétaire
-
GE HSS25IFPWW Le manuel du propriétaire
-
-
GE HSS25GFTWW Le manuel du propriétaire
-
Hotpoint HSM22IFTASA Le manuel du propriétaire
-
-
-
GE HSS22BDMWH Manuel utilisateur