Legrand GEN3 Guide d'installation

Marque: Legrand

Modèle: GEN3

Taper: Guide d'installation

Ce manuel convient également à

Gen3 Low Voltage 4 - Shade Power Panel

LOW VOLTAGE ROLLER SHADE

DISTRIBUTION PANEL

INSTALLATION INSTRUCTIONS

IMPORTANT

Read and understand all instructions before installing.

This document assumes that you have already installed roller

shade brackets.

We do not recommend installing the shade’s wired end in the

locking bracket. Read and understand all instructions before

installing. Always wear personal protection equipment including

safety glasses and gloves. Use a ladder per its manufacturer’s

instructions. Work safely!

Tools Required

• Measuring Tape

• Wire Strippers

• Ladder

• 1/8” Flat Head Screwdriver

Materials Required

• Wire (See table on next page)

Recommended Items

• Wire Management Clips

PARTS LIST

Part Quantity

Power Distribution Panel 1

Male Quick Connector 1 (per shade)

Female Quick Connector 1 (per shade)

INSTALLATION

1. Lay out the Power Distribution Panel and the shades.

Ensure that cords and wires are of sufficient length and

that Distribution Panel is located away from water and

flammable materials.

IMPORTANT: Do not connect power to the Distribution

Panel.

2. Place the shade in the brackets and route the shade’s

wires in such a way that they are hidden from view, but

still accessible. Use wire clips as needed for routing.

3. Terminate the Power Supply’s Quick Connector to

shade’s connector.

4. Please see Qadvanced Roller Shade Gen. 3

Programming Instructions for pairing the remote and

learning shade limits.

Around Back Through Keyhole

Pub #9000146 Revised: 09/2018

For more information visit us at qmotionshades.com or call 877.849.6070

Motorized Roller Shades

QLVS-433, QMLV-433FM

LOW VOLTAGE SHADE

CAN RSS-Gen/CNR-Gen.

FCC Regulatory Statements:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this device not expressly approved by QMotion Advanced Shading Systems could void the user’s authority to

operate the equipment.

Industry Canada Regulatory Statements:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada

This Class B digital apparatus meets all requirements of the Canadian Intereference Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel bouilleur.

Do not operate at temperatures below 32° F or above 130° F. End user must ensure that shade being used is fire resistant. Keep transmitter away

from children. Periodically examine assembly and brackets for signs of wear and discontinue use if repair is necessary. The controller and transmitter

assemblies contain no serviceable parts.

Ton de Zeeuw

Contact for QMotion

Raritan Europe B.V.

Jan van Galenstraat 59

3115 JG Schiedam

The Netherlands

Tel: +31.(0)10.2844040 • Fax: +31.(0)10.2844049

VAT: NL803738614B01 / KvK-CoC: 24256806 / EORI: NL803738614