Whirlpool Cabrio WTW5500XW3 Mode d'emploi

Marque: Whirlpool

Modèle: Cabrio WTW5500XW3

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

Whir

cabr,d

FABRIC CARE SYSTEM

TOP-LOADING

HIGH EFFICIENCY

LOW-WATER WASHER

USE AND CARE GUIDE

GUIDE D'UTILISATION

ET D'ENTRETIEN DE

LA LAVEUSE HAUTE

EFFICACITI_ A FAIBLE

CONSOMMATION D'EAU

AVEC CHARGEMENT PAR

LE DESSUS

Para una version de estas instrucciones en espafiol, visite www.Whirlpool.com

Table of Contents

WASHER SAFETY ......................................................... 2

WHAT'S NEW UNDER THE LiD? ................................. 3

CONTROL PANEL AND FEATURES ............................ 4

CYCLE GUIDE ............................................................... 5

USING YOUR WASHER ................................................ 6

WASHER MAINTENANCE .................................................9

TROUBLESHOOTING ...................................................... 11

WARRANTY ........................................................................16

ASSISTANCE OR SERVICE ...........................Back Cover

Table des mati6res

SI_CURITi_ DE LA LAVEUSE ...................................... 17

QUOI DE NEUF SOUS LE COUVERCLE? ................ 18

TABLEAU DE COMMANDE

ET CARACTERISTIQUES .......................................... 19

GUIDE DES PROGRAMMES ...................................... 21

UTlUSATION DE LA LAVEUSE .................................. 23

ENTRETIEN DE LA LAVEUSE ........................................ 26

DI_PANNAGE ......................................................................29

GARANTIE ..........................................................................35

ASSISTANCE OU SERVICE ..............Couverture arri_re

Designed to use only HE High Efficiency

detergents.

Congue pour I'utilisation d'un d6tergent haute

efficacit6 seulement.

W10338689B

W10338690B =SP

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry=cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry=cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. Ifthe hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

[]

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach intothe washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where itwill be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

WHAT'S NEW UNDER THE LID?

Cleaning with Less Water Automatic Load Size Sensing

Traditional agitator-style

washer

Washer with low-water

washplate wash system

The most striking difference in your new washer is the low-water

washplate wash system. The washer automatically adjusts the

water level to the load size--no water level selector is needed.

Once you start the cycle, the lid will lock, and the washer will

begin the sensing process to determine the correct water level

for the load. This may take several minutes before water is

added. You will find a step-by-step description in the "Cycle

Status Lights" section.

You will hear the motor turn the basket in short pulses to

thoroughly wet the load. This low-water wash method uses

less water and energy compared to a traditional agitator-style

washer.

Choosing the Right Detergent

Use only High Efficiency detergents. The package will be

marked "HE" or "High Efficiency." Low-water washing creates

excessive sudsing with a regular non-HE detergent. Using

regular detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

failures and noticeable mold or mildew. HE detergents are made

to produce the right amount of suds for the best performance.

Follow the manufacturer's instructions to determine the amount

of detergent to use.

Use only High Efficiency (HE) detergent.

Load garments in loose heaps evenly around the washplate.

Do not load garments directly over the center of the washplate;

when loaded, the center of the washplate should be visible.

As the washer dampens and moves the load, the level of the

garments will settle in the basket. This is normal, and does not

indicate that more garments should be added.

IMPORTANT: You will not see a washer basket full of water

as with your past agitator-style washer. It is normal for some

of the load to be above the water line.

Concentrated Cleaning

Low-water cleaning means concentrated cleaning. Rather

than diluting detergent as done in an agitator-style washer,

this washer delivers the detergent directly to the soils.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds and

noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the cycle, as the lid lock goes through a self-test. There

will be different kinds of humming and whirring sounds as the

washplate moves the load. And sometimes, you may hear

nothing at all, as the washer determines the correct water level

for your load or allows time for clothes to soak.

CONTROL PANEL AND FEATURES

POWER

Fabric

Softener

NORMAL

QUICKWASH

l l Havy

ITEMS Hot Extra

START Warm Heavy igh

PausdUnl_k

w_h _f_ Cool Medium

Cold Light pin

DRAIN & SPIN

L_J

Sensing Wash Spin Done

LL°_COk Extra Temp Soil Spin

Rinse Level Speed

I I

O WASH CYCLE KNOB

Use the Wash Cycle knob to select available cycles on your

washer. Turn the knob to select a cycle for your laundry load.

See "Cycle Guide" for detailed descriptions of cycles.

CYCLE OPTIONS

When you select a cycle, its default settings will light up. Not

all cycles and options are available on all models.

TEMP

Temperature Control senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following

the garment label instructions, use the warmest wash

water safe for your fabric.

• Warm and hot water may be cooler than what your

previous washer provided.

• Even in a Cool water wash, some warm water may

be added to the washer to maintain a minimum

temperature.

SOIL LEVEL

For most loads, use the Soil Level that is preset with the

cycle you have chosen. For heavily soiled and sturdy

fabrics, press Soil Level to select more wash time,

if needed. For lightly soiled and delicate fabrics, press

Soil Level to select less wash time, if needed. Lighter

Soil Level setting will help reduce tangling and wrinkling.

SPIN SPEED

This washer automatically selects the spin speed

based on the cycle selected. The preset speeds can be

changed. Not all spin speeds are available with all cycles.

• Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

• Slower spin speeds mean less wrinkling, but will leave

your load more damp.

You may also add or remove options for each cycle. Not all

options can be used with all cycles, and some are preset to

work with certain cycles.

EXTRA RINSE

This option can be used to automatically add a second rinse

to most cycles.

NOTE: Press and hold EXTRA RINSE button for 6 seconds

to turn the button sounds on or off.

FABRIC SOFTENER

This option must be selected if using fabric softener

during a cycle. It ensures that fabric softener is added

at the correct time in the rinse for even distribution.

NOTE: Press and hold FABRIC SOFTENER button for

6 seconds to turn the cycle signal on or off.

CYCLE STATUS LIGHTS INDICATOR

The Cycle Status Lights show the progress of a cycle.

At each stage of the process, you may notice sounds

or pauses that are different from traditional washers.

Sensing Wash Rinse Spin Done

SENSING Sensing Wash Rinse Spin Done

When the START/Pause/Unlock button is pressed,

the washer will first perform a self-test on the lid lock

mechanism. You will hear a click, the basket will make

a slight turn, then lid will unlock briefly before locking

again.

Once the lid has locked the second time, the washer

will use short, slow spins to estimate the load size. These

sensing spins may take 2 to 3 minutes before water is

added to the load and you may hear the hum of these

spins. If the Sensing light is on, the washer is working

properly. You will hear the motor turn the basket in short

pulses to thoroughly wet the load. The washer will then

move the load briefly, pause to allow water to soak into

the load, and resume adding water. This process may

repeat until the correct amount of water has been added

for the load. You may also hear water flowing through the

dispenser, adding detergent to the load.

NOTE: Avoid opening the lid during sensing. The sensing

process will start over when the washer is restarted. The

Sensing light may also come on during the Wash portion

of the cycle. This is normal.

WASH Sensing Wash Rinse Spin Done

You will hear the motor and washplate moving the load.

Unlike traditional washers, the load is not covered with

water. Low-water cleaning means concentrated cleaning.

Rather than diluting detergent, as clone in an agitator-style

washer, this washer delivers the detergent directly to the

soils. The motor sounds may change at different stages

in the cycle. The wash time is determined by the selected

soil level.

RINSE Sensing Wash Rinse Spin Done

You will hear sounds similar to the wash cycle as the

washer rinses and moves the load. You may hear the

motor turning on briefly (short hum) to move the basket

while filling. Fabric softener will be added if the Fabric

Softener option was selected. Some cycles use spray

rinsing.

SPIN Sensing Wash Rinse Spin Done

The washer spins the load at increasing speeds for proper

water removal, based on selected cycle and spin speed.

LID LOCK

To allow for proper load sensing, the lid will lock and the Lid Lock

light will turn on. This light indicates that the lid is locked and

cannot be opened.

DONE Sensing Wash Rinse Spin Done

Once the cycle is complete, this light will come on.

Remove the load promptly for best results.

CYCLE GUIDE

Ifyou need to open the lid, press START/Pause/

Unlock. The lid will unlock once the washer

movement has stopped. This may take several

minutes if the load was spinning at high speed.

Press START/Pause/Unlock again to resume

the cycle.

START

Pause/Unlock

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best fits the load

being washed. Not all cycles and options are available on all models.

Machine-wash silks,

hand-wash fabrics

Small loads,

cottons, polyester,

perm press

Cottons, linens, and

mixed garment loads

Cottons, linens, and

mixed garment loads

No-iron fabrics,

cottons, perm press,

linens, synthetics

Large items such as

sleeping bags, small

comforters, sheets,

jackets

Sturdy fabrics,

colorfast items,

towels, jeans

Swimsuits and items

requiring rinsing

without detergent

Delicate

Quick

Wash

Normal

Eco

Normal

Casual

Bulky

Items

Heavy

Duty

Rinse &

Spin

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

High

Low

No Spin

High

Low

No Spin

High

No Spin

High

Low

No Spin

High

Low

No Spin

High

Low

No Spin

High

Low

No Spin

Extra Heavy

Heavy

Medium

Light

Extra Heaw

Heavy

Medium

Light

Extra Heavy

Heavy

Medium

Light

Extra Heavy

Heavy

Medium

Light

Extra Heaw

Heavy

Medium

Light

Extra Heavy

Heavy

Medium

Light

Extra Heavy

Heavy

Medium

Light

Extra Rinse

Use this cycle to wash lightly soiled garments

indicating "Machine Washable Silks" or "Gentle"

cycle on the care label. Place small items in mesh

garment bags before washing. This cycle uses a

higher, preset water level.

Use this cycle to wash small, lightly soiled loads

of 2-3 items that are needed in a hurry. This cycle

features a spray rinse.

Use this cycle for normally soiled cottons and

mixed fabric loads. This cycle features a spray

rinse.

The Eco Normal cycle allows you to increase your

energy savings compared to the Normal cycle. When

this cycle is used, the wash cycle will use cooler

wash water temperatures than the Normal cycle.

This cycle features a spray rinse.

Use this cycle to wash loads of no-iron fabrics

such as sport shirts, blouses, casual business

clothes, permanent press, and blends.

Use this cycle to wash large items such as

jackets and small comforters. The washer will fill

with enough water to wet down the load before

the wash portion of the cycle begins. Do not

tightly pack basket.

Use this cycle for heavily soiled or sturdy items.

Water-level sensing process may take longer

for some items than for others because they will

absorb more water than other fabric types.

Combines a rinse and spin for loads requiring an

additional rinse cycle or to complete a load after

power interruption. This cycle uses a higher, preset

water level. Also usefor loads that require rinsing only.

Hand-washed items

or dripping

wet items

Heavily soiled

fabrics

No clothes in

washer

Drain &

Spin

Soak Hot

Warm

Cool

Cold

HotClean

Washer

with

affresh ®

High

Low

No Spin

High

Extra Heavy

Heavy

Medium

Light

Extra Heavy

This cycle uses a spin to shorten drying times

for heavy fabrics or special-care items washed

by hand. Use this cycle to drain washer after

cancelling a cycle or completing a cycle after a

power failure.

Use this cycle to soak small spots of set in

stains on fabrics. The washer will use intermittent

agitation and soaking. After time has expired,

water will drain, but the washer will not spin.

Cycle is complete.

Use this cycle every 30 washes to keep the inside

of your washer fresh and clean. This cycle uses a

higher water level. Use with affresh®washer cleaner

tablet or liquid chlorine bleach to thoroughly clean

the inside of your washer. This cycle should not be

interrupted. See "Washer Care."

IMPORTANT: Do not place garments or other items

in the washer during the Clean Washer with affresh®

cycle. Use this cycle with an empty wash tub.

*All rinses are cold.

USING YOUR WASHER

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Doing so can result in death, explosion, or fire.

1, Sort and prepare your laundry

* Empty pockets. Loose change, buttons, or any small

object can pass under the washplate and become trapped,

causing unexpected sounds.

. Sort items by recommended cycle, water temperature,

and colorfastness.

. Separate heavily soiled items from lightly soiled.

. Separate delicate items from sturdy fabrics.

. Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

. Treat stains promptly.

. Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

. Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

* When washing water-proof or water-resistant items, load

evenly. See "Cycle Guide" for tips and more information on

using the Bulky Items cycle.

. Use mesh garment bags to help avoid tangling when

washing delicate or small items.

. Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Single-dose laundry packet, color-safe bleach, Oxi-type

boosters, or fabric softener crystals can be added to basket

prior to adding laundry.

NOTE: Do not add clothes to washer basket prior to adding

laundry products. Always follow manufacturer's instructions.

Load laundry into washer

Load garments in loose heaps evenly

around the washplate. Do not load

garments directly over the center

of the washplate; when loaded, the

center of the washplate should be

visible. Try mixing different sized

garments to reduce tangling.

IMPORTANT: Garments need to move freely for best cleaning

and to reduce wrinkling and tangling.

to dispenser, if desired

Do not overfill, dilute, or use more than 1 cup (250 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

if desired

Fabric softener tray

Using Laundry Product Dispensers

NOTE: Do not add single-dose laundry packets, color-safe

bleach, Oxi-type boosters, or fabric softener crystals to

dispensers. They will not dispense correctly.

Add HE detergent to dispenser

Detergent tray

Add a measured amount of HE detergent

into detergent tray. This tray holds 3 oz.

(89 mL). Do not overfill tray - adding too much detergent may

cause detergent to be dispensed into the washer too early.

IMPORTANT: Use only High Efficiency detergents. The

package will be marked "HE" or "High Efficiency." Low-water

washing creates excessive sudsing with a regular non-HE

detergent. Using regular detergent will likely result in longer

cycle times and reduced rinsing performance. It may also

result in component failures and noticeable mold or mildew.

HE detergents are made to produce the right amount of

suds for the best performance. Follow the manufacturer's

instructions to determine the amount of detergent to use.

HELPFUL TIP: See "Washer Maintenance" for information

on recommended method of cleaning washer dispenser trays.

Fabric

Softener

Pour a measured amount of liquid fabric softener

into tray, always follow manufacturer's directions

for correct amount of fabric softener based on your load size.

Close dispenser drawer, then select Fabric Softener option.

IMPORTANT: Fabric Softener option must be selected to

ensure proper distribution at correct time in cycle. Do not

overfill or dilute. Overfilling dispenser will cause fabric softener

to immediately dispense into washer.

If Extra Rinse option is selected, fabric softener will be

dispensed into the last rinse.

It is normal for a small amount of water to remain in the

dispenser at the end of a cycle.

7. Press POWER to turn on washer

POWER

Make sure the dispenser drawer is closed completely, then

press POWER to turn on the washer.

8. Select cycle

NORMAL

QUICKWASH E(O ,J():_A

DELICATE CASUAL

BULKY

ITEMS

CLEAI_ tEAVY

WASHEI_ DUTY

with affre_

SOAK _INSE & SPIN

DRAIN & SPIN

Turn cycle knob to choose your wash cycle. For more

information, see "Control Panel."

9, Select cycle settings

I Hot l Extra Heavy

Warm l Heavy IHigh

_i IM_II um l LNoWspin

Temp Soil Spin

Level Speed

Once you select a cycle, the default settings for that cycle

will be lit. Press the cycle settings buttons to change the

Temperature, Soil Level, and Spin Speed, if desired.

NOTE: Always read and follow fabric care label instructions

to avoid damage to your garments.

Wash Temp

energy. This will be cooler than Durable garments

your hot water heater setting. Heavy soils

Warm

Some cold water will be added,

so this will be cooler than what

Bright colors

Moderate to light soils

0, select cycle options

CD CD

Fabric Extra

Softener Rinse

Select any other cycle options you may wish to add, if not

previously set. Some cycles will automatically add certain

options such as Extra Rinse. These can be turned off, if

desired.

NOTE: Not all options are available with all cycles.

1 1. Press START/Pause/Unlock

to begin wash cycle

START

Pause/Unlock

Press the START/Pause/Unlock button to start the wash

cycle. Filling is delayed for several minutes while load balance

is sensed.When the cycle has finished, the DONE indicator

will light. Promptly remove garments after cycle has

completed to avoid odor, reduce wrinkling, and rusting of

metal hooks, zippers, and snaps.

Unlocking the lid to add garments

If you need to open the lid to add 1 or 2 missed garments:

Press START/Pause/Unlock; the lid will unlock once

the washer movement has stopped. This may take several

minutes if the load was spinning at high speed. Then close

the lid and press START/Pause/Unlock again to restart

the cycle.

If lid is left open for more than 10 minutes, water will pump

out.

Delay in water fill

Filling is delayed for 2 to 3 minutes to check for load

unbalance. You will hear the hum of the spin prior to filling.

This is normal operation.

WASHER MAINTENANCE

WATER iNLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of

hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See the

"installation Instructions" for more information.

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always use High Efficiency (HE) detergents and follow the

HE detergent manufacturer's instructions regarding the

amount of HE detergent to use. Never use more than the

recommended amount because that may increase the rate

at which detergent and soil residue accumulate inside your

washer, which in turn may result in undesirable odor.

2. Use warm and hot wash water settings sometimes (not

exclusively cold water washes), because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer lid open between uses to help

dry out the washer and prevent the buildup of odor-

causing residue.

Cleaning Your Top Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This Washer

Maintenance Procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above, and use this recommended monthly cleaning

procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water

volumes in combination with affresh ®Washer Cleaner

or liquid chlorine bleach to clean the inside of the washer.

Begin procedure

1. affresh ®Washer Cleaner Cycle Procedure

{Recommended for Best Performance}:

a. Open the washer lid and remove any clothing or items.

b. Place an affresh ®Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh ®Washer Cleaner tablet

in the detergent dispenser.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid.

f. Select the CLEAN WASHER cycle.

g. Press the START/Pause/Unlock button to begin the

cycle. The Clean Washer Cycle Operation is described

below.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press POWER. (For models with

no Power/Cancel button, press and hold START/Pause/

Unlock for three seconds). After the Clean Washer cycle

has stopped, run a RINSE & SPIN cycle to rinse cleaner

from washer.

WASHER CARE (cont.)

2. Chlorine Bleach Procedure {Alternative}:

a. Open the washer lid and remove any clothing

or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Select the CLEAN WASHER cycle.

f. Press the START/Pause/Unlock button to begin the

cycle. The Clean Washer Cycle Operation is described

below.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press POWER. (For models with

no Power/Cancel button, press and hold START/Pause/

Unlock for three seconds). After the Clean Washer cycle

has stopped, run a RINSE & SPIN cycle to rinse cleaner

from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will fill to a water level higher than in normal

wash cycles to provide rinsing at a level above the water

line for normal wash cycle.

2. During this cycle, there will be some agitation and spinning

to increase the removal of soils.

After this cycle is complete, leave the lid open to allow

for better ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may find some

residue buildup in the washer's dispensers. To remove

residue from the dispensers, wipe them with a damp cloth

and towel dry. Do not attempt to remove the dispensers or

trim for cleaning. The dispensers and trim are not removable.

Ifyour model has a dispenser drawer, however, remove the

drawer and clean it before or after you run the Clean Washer

cycle. Use an all-purpose surface cleaner, if needed.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills.

Use only mild soaps or cleaners when cleaning external

washer surfaces.

iMPORTANT: To avoid damaging the washer's finish, do not

use abrasive products.

f CLEANING YOUR DISPENSER TRAY -"

You may find laundry product residue in your dispenser

trays. To remove residue, follow this recommended cleaning

procedure:

1. Pull tray out until you feel resistance.

2. Lift up slightly, and then continue pulling out.

3. Wash in warm, soapy water, using a mild detergent.

4. Rinse with warm water.

5. Air dry, or dry with a towel, then place back into slot.

iMPORTANT: Dispenser trays are dishwasher safe.

NON=USE AND VACATION CARE

Operate your washer only when you are home. If moving,

or not using your washer for a period of time, follow these

steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid flooding due

to water pressure surge.

WINTER STORAGE CARE

iMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on RINSE & SPIN cycle for about 30 seconds to

mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

WINTER STORAGE CARE directions before moving.

3. Disconnect drain from drain system and drain any

remaining water into a pan or bucket. Disconnect drain

hose from back of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer basket.

6. Drape power cord over edge and into washer basket.

7. Place packing tray from original shipping materials back

inside washer. If you do not have packing tray, place

heavy blankets or towels into basket opening. Close lid

and place tape over lid and down front of washer. Keep

lid taped until washer is placed in new location.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong,

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

RE! NSTALLING/USI NG WASHER AGAI N

To reinstall washer after non-use, vacation, winter storage,

or moving:

Refer to Installation Instructions to locate, level, and

connect washer.

Before using again, run washer through the following

recommended procedure:

use washer again:

Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

Plug in washer or reconnect power.

Run washer through BULKY ITEMS cycle to clean

washer and remove antifreeze, if used. Use only HE

High Efficiency detergent. Use half the manufacturer's

recommended amount for a medium-size load.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

if you experience I Possible Causes Solution

Check the following for

proper installation or see

"Using Your Washer"

section.

Feet may not be in contact

with the floor and locked.

Washer may not be level.

Load could be unbalanced.

Front and rear feet must be in firm contact with floor, and washer

must be level to operate properly. Jam nuts must be tight

against the bottom of the cabinet.

Check floor for flexing or sagging, if flooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See "Level the Washer" in the "installation Instructions".

Load garments in loose heaps evenly around the washplate.

Do not load garments directly over the center of the washplate.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Wash smaller loads to reduce imbalance.

Use Bulky Item cycle for oversized, non-absorbent items such as

jackets and small comforters.

See "Cycle Guide" and "Using Your Washer" in this "Use and

Care Guide".

Clicking or metallic

noises

Gurgling or humming

Humming

Check the following for

proper installation:

Not enough water

in washer

Objects caught in washer

drain system.

Washer may be draining water.

The sensing light is on.

Washer not level.

Fill hoses not attached tightly.

Fill hose washers

Drain hose connection

Check household plumbing

for leaks or clogged sink or drain.

Washer not loaded properly.

Load not completely covered

in water.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump.

it may be necessary to call for service to remove items.

it is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

it is normal to hear the pump making a continuous humming sound

with periodic gurgling or surging asfinal amounts of water are

removed during the spin/drain cycles.

You may hear the hum of the sensing spins after you have started

the washer. This is normal. Sensing spins will take several minutes

before water is added to the washer.

Water may splash off basket if washer is not level.

Tighten fill-hose connection.

Make sure all four fill hose flat washers are properly seated.

Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Water can back up out of a clogged sink or drainpipe. Check

all household plumbing for leaks (laundry tubs, drain pipe,

water pipes, and faucets.)

Unbalanced loading can cause basket to be out of alignment

and cause water to splash off tub. See "Using Your Washer"

for loading instructions.

This is normal operation for an HE low-water washer. The load will

not be completely under water. The washer senses load sizes and

adds correct amount of water for optimal cleaning. See "What's

New under the Lid."

IMPORTANT: Do not add more water to washer. Adding water lifts

the garments off the washplate, resulting in lesseffective cleaning, j

TROUBLESHOOTING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to fogow these instructions can result in death,

fire, or electrical shock.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

if you experience j

Washer won't run or fill,

washer stops working

or wash light remains

on (indicating that the

washer was unable to

fill appropriately)

Possible Causes

Check for proper water supply.

Check proper electrical supply.

Normal washer operation.

Washer may be tightly packed.

Not using HE detergent or using too

much HE detergent.

Solution

Both hoses must be attached and have water flowing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water flow.

Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Lid must be closed for washer to run.

Washer will pause during certain phases of cycle.

Do not interrupt cycle.

Washer may be stopped to reduce suds.

The washer senses the dry load with short spins that may take

2 to 3 minutes before the water is added. You may hear the

hum of the spins. This is normal.

Remove several items, rearrange load evenly around the

washplate. Do not load garments directly over the center of the

washplate. Close lid and press Start/Pause.

Add only 1 or 2 additional garments after washer has started.

Do not add more water to the washer.

Only use HE detergent. Suds from regular detergents can slow

or stop the washer. Always measure detergent and follow

detergent directions based on your load requirements.

To remove suds, cancel cycle. Select RINSE & SPIN. Press

START/Pause/Unlock. Do not add more detergent, j

TROUBLESHOOTING

if you experience

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Possible causes _ Solution

Washer not draining/

spinning, loads are

still wet or spin light

remains on (indicating

that the washer was

unable to pump out

water within ten

minutes)

Dry spots on load

after cycle

Incorrect or wrong

wash or rinse

temperatures

Empty pockets and use garment bags

for small items.

Use a cycle with a low spin speed.

The washer may be tightly packed

or unbalanced.

Check plumbing for correct drain

hose installation. Drain hose extends

into standpipe farther than 4.5"

(114 mm).

Wrong or too much detergent

causing suds to slow or stop

draining and spinning.

High speed spins extract more

moisture than traditional top-load

washers.

Check for proper water supply.

Small items may have been caught in pump or between basket

and tub, which can slow draining.

Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed spin

for your garment. To remove extra water in the load, select

DRAIN & SPIN. Load may need to be rearranged to allow even

distribution of the load in the basket.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select DRAIN &

SPIN to remove excess water. See "Using Your Washer" for

loading recommendations.

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening. Lower drain hose ifthe end is higher than 96" (2.4 m)

above the floor. Remove any clogs from drain hose.

Use only HE detergent. Always measure and follow detergent

directions for your load. To remove extra suds, select RINSE &

SPIN. Do not add detergent.

The high spin speeds combined with air flow during the final

spin can cause items near the top of the load to develop dry

spots during the final spin. This is normal.

Energy-saving controlled

wash temperatures.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Not using HE detergent or using too

much HE detergent.

Washer may be tightly packed.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water flowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

ENERGY STAR®qualified washers use cooler wash and rinse

water temperatures than traditional top-load washers. This

includes cooler hot and warm washes.

Both hoses must be attached and have water flowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

The suds from regular detergent can keep washer

from operating correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions

based on load size and soil level.

The washer is less efficient at rinsing when load is tightly

packed.

Load garments in loose heaps evenly around the washplate. Do

not load garments directly over the center of the washplate.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

TROUBLESHOOTING

f First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

if you experience

Sand, pet hair, lint, etc.

on load after washing

Load is tangling

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Possible Causes I Solution

Heaw sand, pet hair, lint, and

detergent or bleach residues

may require additional rinsing.

Washer not loaded as recommended.

Not cleaning or Wash load not completely

removing stains covered in water.

Added more water to washer.

Washer not loaded properly.

Not using HE detergent or using too

much HE detergent.

Not using correct cycle for fabric type.

Not using dispensers.

Not washing like colors together.

Normal dispenser operation.

Small amount of

water still in

dispenser after

_,_ycle

Add an Extra Rinse to the selected cycle.

See "Using Your Washer" section.

See "Cycle Guide" to match your load with the best cycle.

Select a cycle with a slower wash action and spin speed;

however, items will be wetter than those using a higher speed

spin.

Load garments in loose heaps evenly around the washplate. Do

not load garments directly over the center of the washplate.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move.

Do not add more water to washer. Adding water lifts the

garments off the washplate, resulting in less effective cleaning.

Washer is less efficient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the washplate. Do

not load garments directly over the center of the washplate.

Add only 1 or 2 additional garments after washer has started.

The suds from regular detergent can keep washer from

operating correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow manufacturer's directions

based on load size and soil level.

Use a higher soil level cycle option and warmer wash

temperature to improve cleaning.

If using Quick Wash cycle, wash only a few items.

Use Whites and Heavy Duty cycle for tough cleaning.

See "Cycle Guide" to match your load with the best cycle.

Use dispensers to avoid chlorine bleach and fabric softener

staining.

Load dispensers before starting a cycle.

Avoid overfilling.

Do not add products directly onto load.

Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

It is normal for small amounts of water to remain in dispenser.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Incorrect dispenser

operation

Clogged dispensers or laundry

products dispensing too soon.

Residual powder in dispenser.

Solution

Do not overfill dispenser, which causes immediate dispensing.

Always select Fabric Softener option to assure proper dispensing.

Load dispensers before starting a cycle.

Homes with low water pressure may result in residual powder in the

dispenser. Toavoid, select a warmer wash temperature if possible,

depending on your load, or use liquid HE detergent.

Use only liquid chlorine bleach inthe bleach dispenser.

In wash water temperatures colder than 60° F (15.6° C), some

detergents do not dissolve well. Soils may be difficult to remove.

Toavoid, select a warmer wash temperature if possible, depending

on your load, or use liquid HE detergent.

Fabric damage Sharp items were in pockets during Empty pockets, zip zippers, and snap or hook fasteners before

wash cycle, washing to avoid snags and tears.

Strings and straps could have tangled. Tie all strings and straps before starting wash load.

Mend rips and broken threads in seams before washing.

Items may have been damaged before

washing.

Fabric damage can occur if washer

is tightly packed.

Liquid chlorine bleach may have been

added incorrectly.

Button sounds are turned off.

Cycle signal is turned off.

Monthly maintenance not done as

recommended.

Garment care instructions may not

have been followed.

No sounds when

buttons are pressed

No end of cycle signal

Odors

Using wrong or too much detergent.

Lid Locked light The lid is not closed.

is flashing. A cycle was stopped or paused using

the START/Pause/Unlock button.

Single-dose laundry Adding laundry packet incorrectly.

packet not dissolving

Load garments in loose heaps evenly around the washplate. Do

not load garments directly over the center of the washplate.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

Always read and follow garment manufacturer's care label

instructions. See "Cycle Guide" to match your load with

the best cycle.

Button sounds can be turned on or off by pressing and holding

EXTRA RINSE for 6 seconds.

Cycle signal can be turned on or off by pressing and holding

FABRIC SOFTENER for 6 seconds.

Run the Clean Washer with affresh ®cycle after every 30 washes.

See "Washer Care" in Washer Maintenance.

Unload washer as soon as cycle is complete.

Use only HE detergent. Be sure to measure correctly.

Always follow the manufacturer's directions.

See "Washer Care" section.

Close the lid. The washer will not start or fill with the lid open.

The washer may still be spinning. The lid will not unlock until the

basket has stopped spinning. This may take several minutes if

washing large loads or heavy fabrics.

Be sure laundry packet is added to washer basket before adding

clothes. Do not add packet to dispenser. Follow the manufacturer's

instructions to avoid damage to your garments, j

WHIRLPOOL CORPORATION LAUNDRY WARRANTY

LiMiTED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory

Specified Replacement Parts and repair labor to correct defects in materials or workmanship that existed when this major appliance

was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

Service must be provided by aWhirlpool designated service company. This limited warranty is valid only in the United States or

Canada and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective

from the date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

iTEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters, or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF iMPLiED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABiLiTY OR iMPLiED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply

to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to

province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

LIMiTATiON OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR iNCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve

the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by

calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 10/11

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in=warranty service.

Write clown the following information about your major appliance

to better help you obtain assistance or service if you ever need

it. You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

ModeJ number

Serial number

Purchase date

S] CURIT] DE LA LAVEUSE

Votre s_curit6 et celle des autres est tres importante,

Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.

Assurez=vous de toujours lire tousles messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit6.

Ce symbole d'alerte de s6curite vous signale les dangers potentiels de d6ces et de blessures graves

& vous et & d'autres.

Tousles messages de securit6 suivront le symbole d'alerte de securit6 et le mot "DANGER" ou

"AVERTISSEMENT'. Ces mots signifient :

Risque possible de d6c_s ou de blessure grave si

vous ne suivez pas irnm_diaternent les instructions,

Risque possible de d_c_s ou de blessure grave

si vous ne suivez pas les instructions.

Tousles messages de securit6 vous diront quel est le danger potentiel et vous disent comment reduire le risque de

blessure et ce qui peut se produire en cas de non-respect des instructions.

IlVlPORTANTES INSTRUCTIONS DE sf--cURITI=-

AVERTISSEMENT : Pour r6duire les risques d'incendie, de choc 61ectrique ou de blessures Iors de I'utilisation de la

laveuse, suivre les pr6cautions fondamentales dont les suivantes :

[] Lire toutes les instructionsavant d'utiliser la laveuse.

[] Ne pas laver des articles qui ont et6 nettoyes ou

laves avec de I'essence ou imbibes d'essence,

solvants de nettoyage a sec, ou autres substances

inflammables ou explosives; ces substances

peuvent emettre des vapeurs susceptibles de

s'enflammer ou d'exploser.

[] Ne pas ajouter d'essence, solvant de nettoyage &

sec ou autre produit inflammable ou explosif dans

I'eau de lavage. Ces substances peuvent emettre

des vapeurs susceptibles de s'enflammer ou

d'exploser.

[] Dans certaines conditions, de I'hydrogene gazeux

peut se former dans un circuit d'eau chaude qui n'a

pas ete utilise pendant 2 semaines ou plus. LE GAZ

HYDROGI_NE EST EXPLOSlBLE. Si le circuit d'eau

chaude n'a pas ete utilise pendant une telle periode,

avant d'utiliser la laveuse, ouvrir tousles robinets

d'eau chaude et laisser I'eau s'ecouler pendant

plusieurs minutes par chaque robinet. Ceci

permettra I'evacuation de I'hydrogene gazeux

accumule. Comme ce gaz est inflammable, ne pas

fumer ou utiliser une flamme nue au cours de cette

periode.

[] Ne pas laisser des enfants jouer sur ou &I'interieur de la

laveuse. Bien surveiller les enfants Iorsque la laveuse est

utilisee a.proximite d'enfants.

[] Avant de mettre la laveuse au rebut ou hors de service,

enlever la porte ou le couvercle.

[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de

la laveuse Iorsque le tambour, la cuve ou I'agitateur est en

mouvement.

[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle

serait exposee aux intemperies.

[] Ne pas modifier les organes de commande.

[] Ne pas reparer ou remplacer un composant quelconque de

la laveuse, ni entreprendre une operation de service, si ce

n'est specifiquement recommande dans ce manuel ou dans

un manuel d'instructions de reparations destine & I'utilisateur;

ilest alors essentiel que la personne concernee comprenne

ces instructions et soit competente pour les executer.

[] Pour les instructions de liaison & la terre, voir "Specifications

electriques" dans les instructions d'installation.

CONSERVEZ CES INSTRUCTIONS

Avertissements de la proposition 65 de I'€:tatde Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour etre & I'origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'€:tat de Californie pour _tre & I'origine de

malformations et autres d6ficiences de naissance.

QUOI DE NEUF SOUS LE COUVERCLE?

Nettoyer avec moins d'eau

Laveuse & faible consommation

d'eau avec plateau de lavage

Traditional agitator-style

washer

La nouveaut6 la plus remarquable de cette nouvelle laveuse

est son systeme de lavage a faible consommation d'eau avec

plateau de lavage. La laveuse ajuste automatiquement le

niveau d'eau en fonction de la taille de la charge - nul besoin

de s61ecteur de niveau d'eau.

D tection automatique

de faille de charge

Une fois que I'on d6marre le programme, le couvercle se

verrouille et la laveuse entame un processus de d6tection pour

d6terminer le niveau d'eau appropri6 a la charge. Cela peut

prendre plusieurs minutes avant que I'eau ne soit ajout6e. Voir

la description pas-a-pas dans la section "T6moins lumineux

de programme".

Vous entendrez le moteur faire tourner le panier par de brefs

mouvements d'impulsion pour bien imbiber la charge. Cette

m6thode de lavage avec faible consommation d'eau utilise moins

d'eau et d'6nergie qu'une laveuse traditionnelle de type agitateur.

Choix du d tergent appropri

Utiliser uniquement des d6tergents Haute efficacit6.

Uemballage portera la mention "HE" ou "High Efficiency"

(haute efficacit6). Un lavage avec faible consommation

d'eau produit un exces de mousse avec un d6tergent non HE

ordinaire. II est probable que I'utilisation d'un d6tergent ordinaire

prolongera la dur6e des programmes et r6duira la performance

de ringage. Ceci peut aussi entrainer des d6faillances des

composants et une moisissure perceptible. Les d6tergents HE

sent congus pour produire la quantit6 de mousse ad6quate

pour le meilleur rendement. Suivre les recommandations

du fabricant pour d6terminer la quantit6 de d6tergent a utiliser.

Utiliser uniquement un detergent Haute efficacite (HE).

Charger les v6tements sans les tasser et de fa£;on uniforme

le long du plateau de lavage. Ne pas placer les v@ements

directement au centre du plateau de lavage - celui-ci dolt

6tre visible.

_, mesure que la laveuse imbibe et d6place la charge, les

v_tements se tassent dans le panier. Ceci est normal et ne

signifie pas que I'on delve rajouter des vStements.

IMPORTANT : Le panier de la laveuse ne sera pas rempli d'eau,

comme avec votre pr6c6dente laveuse de type agitateur. II est

normal qu'une partie de la charge d6passe du niveau d'eau.

Nettoyage concentr

Le systeme de lavage h faible consommation d'eau signifie un

lavage concentr6. Plut6t que de diluer du d6tergent comme

dans une laveuse de type agitateur, cette laveuse libere le

d6tergent directement sur les endroits souill6s.

Sons normaux pr( visibles

Au cours des diff@ents stades du programme de lavage, vous

entendrez peut-Stre des bruits que votre laveuse pr6c6dente

ne produisait pas. Par exemple, vous entendrez peut-Stre

un cliquetis au d6but du programme Iorsque le systeme de

verrouillage du couvercle effectue un test automatique. On

entendra diff@ents bourdonnements et bruits de frottements

rythmiques a mesure que I'impulseur d6place la charge. Parfois,

il est possible que la laveuse soit completement silencieuse,

Iorsqu'elle d6termine le niveau d'eau ad6quat ou qu'elle laisse

tremper les v_tements.

TABLEAU DE COMMANDE ET CARACTERISTIQUES

NODAL

QUICKWASH

POWER

Fabric

Softener

BULKY _ l

ITEMS Hot

START Warm

Pause/Ufll_k

w_haf_ Cool

Cold

DRAIN & SPIN

SensingWash R_e Spin Done LocDdk

Extra Temp

Rinse

I I

Heavy igh

Medium

Light pin

Soil Spin

Level Speed

BOUTON DE PROGRAMME DE LAVAGE

Utiliser le bouton de programme pour s61ectionner les

programmes disponibles de la laveuse un programme

correspondant a la charge de linge. Tourner le bouton

pour s61ectionner un cycle de charge de linge. Voir "Guide

de programmes" pour des descriptions de programmes

d6taill6es.

OPTIONS DE PROGRAMMES

Lorsqu'on s61ectionne un programme, ses r6glages par

d6faut s'allument. Certains programmes et options ne sont

pas disponibles sur certains modeles.

TEMP (Temperature}

La fonction de contr61e de temp6rature d6tecte et

maintient une temp6rature uniforme de I'eau en r6gulant

le d6bit d'arriv6e d'eau chaude et d'eau froide.

S61ectionner une temp6rature de lavage en fonction

du type de tissu et de salet6 a laver. Pour des r6sultats O

optimaux, suivre les instructions sur 1'6tiquette du

v&tement et utiliser la temperature d'eau de lavage la plus

chaude possible qui reste sans danger pour le tissu.

• Les temperatures de I'eau tiede et de I'eau chaude

seront inf6rieures a celles de votre pr6c6dente laveuse.

• M_me avec un r6glage de lavage a I'eau froide, il est

possible que de I'eau tiede soit ajout6e a la laveuse

pour maintenir une temp6rature minimale.

SOIL LEVEL (Niveau de salet_}

Pour la plupart des charges, utiliser Soil Level (niveau de

salet6) pr6r6gl6 pour le programme choisi. Pour les tissus

tr_s sales et robustes, appuyer sur Soil Level (niveau de

salet6) pour prolonger la dur6e de lavage si n6cessaire.

Pour les tissus peu sales et d61icats, appuyer sur Soil

Level (niveau de salet6) pour abr6ger la dur6e de lavage

si n6cessaire. Un r6glage de niveau de salet6 inf6rieur

aidera a r6duire I'emm61ement et le froissement.

SPIN SPEED (Vitesse d'essorage)

Cette laveuse s61ectionne automatiquement la Vitesse

d'essorage en fonction du programme s61ectionn& Les

vitesses pr6r6gl6es peuvent 6tre modifi6es. Sur certains

programmes, certaines vitesses d'essorage ne sont pas

disponibles.

• Des vitesses d'essorage plus 61ev6es signifient des

dur6es de s6chage plus courtes mais elles peuvent

augmenter le froissement de la charge.

• Des vitesses d'essorage plus lentes signifient moins

de froissement mais laissent la charge plus humide.

On peut aussi ajouter ou supprimer des options pour chaque

programme. Noter que certaines options ne peuvent pas _tre

utilis6es avec certains programmes, et que certaines d'entre

elles sont pr6r_glees pour ne fonctionner qu'avec certains

programmes.

EXTRA RINSE (Rin£age suppl_mentaire}

On peut utiliser cette option pour ajouter

automatiquement un second ringage & la plupart

des programmes.

REMARQUE : Appuyer sur EXTRA RINSE (rin£:age

suppl_mentaire) pendant 6 secondes pour activer ou

d_sactiver le son des boutons.

FABRIC SOFTENER (Assouplissant pour tissu)

Cette option dolt 6tre s_lectionn_e si I'on utilise

de I'assouplissant pour tissu durant un programme.

Ceci garantit que I'assouplissant pour tissu est

ajoute au bon moment Iors du ringage pour 6tre

correctement distribu&

REMARQUE : Appuyer sur FABRIC SOFTENER

(assouplissant pour tissu) pendant 6 secondes pour

activer ou d_sactiver les signaux sonores de programme.

TEMOINS LUMINEUX DES PROGRAMMES

Les t6moins lumineux indiquent la progression du

programme. _, chaque 6tape du processus, il est possible

que I'on remarque des pauses ou des sons diff@ents

de ceux que I'on remarque avec des laveuses ordinaires.

Sensing Wash Rinse Spin Done

SENSING (D_tection)

Sensing Wash Rinse Spin Done

Lorsqu'on appuie sur le bouton START/Pause/Unlock

(Mise en marche/pause/d6verrouillage), la laveuse

effectue un test automatique sur le m6canisme de

verrouillage du couvercle. On entend un d6clic,

le panier effectue un 16gertour, et le couvercle se

d6verrouille brievement avant de se verrouiller

nouveau.

Une fois le couvercle verrouill6 pour la deuxieme fois,

la laveuse utilise des essorages lents et courts pour

estimer le volume de la charge. Ces essorages de

d6tection peuvent prendre 2 a 3 minutes avant que

de I'eau ne soit ajout6e a la charge et les essorages

peuvent 6mettre un bourdonnement. Si le t6moin

lumineux de d6tection est allum6, cela signifie que

la laveuse fonctionne correctement. On entend

le moteur qui fait tourner le panier par de de courtes

impulsions pour mouiller I'int6gralit6 de la charge.

La laveuse d6place ensuite brievement la charge,

fait une pause pour permettre a I'eau de tremper

la charge, et continue a ajouter de I'eau. Ce processus

peut se r6p6ter jusqu'a ce que la quantit6 d'eau

correcte ait 6t6 ajout6e a la charge. II est aussipossible

que I'on entende de I'eau couler dans le distributeur,

ajoutant le d6tergent a la charge.

REMARQUE : €:viter d'ouvrir le couvercle pendant

la d6tection de la charge. Le processus de d6tection

reprend depuis le d6but quand la laveuse est remise

en marche. Le t6moin de d6tection peut s'allumer

6galement lots des 6tapes de trempage et de lavage

du programme. Ceci est normal.

RINSE (Ringage}

Sensing Wash Rinse Spin Done

On entend des sons similaires a ceux entendus lots

du programme de lavage a mesure que la laveuse rince et

d6place la charge. Vous pouvez entendre le moteur tourner

brievement pour d6placer le panier pendant le remplissage.

Uassouplissant pour tissu sera distribu6 si I'option Fabric

Softener (Assouplissant pour tissu) a 6t6 s61ectionn6e.

Quelques programmes utilisent un ringage par vaporisation.

SPIN (Essorage)

Sensing Wash Rinse Spin Done

La laveuse essore la charge a des vitesses augmentant

graduellement pour une bonne extraction de I'eau,

en fonction du programme et de la vitesse d'essorage

s61ectionn6e.

DONE (Termin_}

Sensing Wash Rinse Spin Done

Une fois le programme termin6, ce t6moin s'allume.

Retirer la charge rapidement pour un r6sultat optimal.

LID LOCK (Verrouillage de couvercle)

Pour permettre une bonne d6tection de la charge,

le couvercle se verrouille et le t6moin de Verrouillage

du couvercle s'allume. Ce t6moin lumineux indique que

le couvercle est verrouill6 et ne peut 6tre ouvert.

Si I'on doit ouvrir le couvercle, appuyer sur

START/Pause/Unlock (Mise en marche/

pause/d6verrouillage). Le couvercle se

d6verrouille une fois que le mouvement

de la laveuse a cess6. IIse peut que cela

prenne plusieurs minutes si la laveuse

essorait la charge a grande vitesse. Appuyer

de nouveau sur START/Pause/Unlock (Mise en marche/

pause/d6verrouillage) pour poursuivre le programme.

START

Pause/Unlock

WASH (Lavage)

Sensing Wash Rinse Spin Done

On entend le moteur et le plateau de lavage d6placer

la charge. Contrairement aux laveuses ordinaires,

la charge n'est pas completement submerg6e dans

I'eau. Un nettoyage avec faible niveau d'eau signifie

un nettoyage concentr6. Plut6t que de diluer du

d6tergent, comme dans une laveuse de type agitateur,

cette laveuse libere le d6tergent directement sur les

endroits souill6s. Les bruits 6mis par le moteur peuvent

changer Iors des diff@entes 6tapes du programme. La

dur6e de lavage est d6termin6e par le niveau de salet6

s61ectionn6.

La page charge ...

Whirlpool Cabrio WTW5500XW3 Mode d'emploi

Marque: Whirlpool

Modèle: Cabrio WTW5500XW3

Catégorie: Machines à laver

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool Cabrio WTW5500XW3 User guide

Whirlpool Cabrio WTW5500XW3 Mode d'emploi

Ce manuel convient également à

Whirlpool Cabrio WTW5500XW3 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents