Maytag MCS 67002813 Le manuel du propriétaire

Marque: Maytag

Modèle: MCS 67002813

Catégorie: Frigos

Taper: Le manuel du propriétaire

Form No. A/1/03 Part No. 12591317 MCS 67002813 Litho U.S.A.

SIDE-BY-SIDE REFRIGERATOR

Installer: Please leave this manual with

this appliance.

Consumer: Please read and keep this

manual for future reference. Keep sales

receipt and/or cancelled check as proof of

purchase.

In our continuing effort to improve

the quality and performance of our

appliances, it may be necessary to

make changes to the appliance

without revising this guide.

Model Number

Serial Number

Date of Purchase

WNER

ANUAL

CONTENTS

Important Safety Instructions.....................................1

Installation ..............................................................2-6

Fresh Food Features..............................................7-8

Freezer Features .......................................................9

Dispenser Features .................................................10

Filtration System ......................................................11

Water Filter Data .....................................................12

Care and Cleaning .............................................13-15

Normal Operating Sounds.......................................16

Before You Call for Service ................................17-18

Warranty ..................................................................19

Manuel du Propriétaire ............................................20

Manuel du Propriétaire ............................................40

Before calling for service

If something seems unusual, please check Before

You Call for Service section, which is designed to

help you solve problems before calling service.

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

What you need to know

about safety

instructions

Warning and Important Safety In-

structions appearing in this manual are

not meant to cover all possible conditions

and situations that may occur. Common

sense, caution and care must be exer-

cised when installing, maintaining or

operating refrigerator.

Always contact your dealer, distributor,

service agent or manufacturer about

problems or conditions you do not under-

stand.

DANGER – Immediate hazards which

WILL result in severe personal injury

or death.

DANGER

WARNING – Hazards or unsafe prac-

tices which COULD result in severe

personal injury or death.

WARNING

CAUTION – Hazards or unsafe prac-

tices which COULD result in minor

personal injury.

CAUTION

To reduce risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic precautions,

including the following:

WARNING

To reduce risk of injury or death,

follow basic precautions, including

the following:

IMPORTANT: Child entrapment and

suffocation are not problems of the

past. Junked or abandoned refrigera-

tors are still dangerous – even if they

sit out for “just a few days.” If you are

getting rid of your old refrigerator,

please follow the instructions below to

help prevent accidents.

Before you throw away your old refrig-

erator or freezer:

➢ Ta ke off the doors.

➢ Leave the shelves in

place so children

may not easily climb

inside.

WARNING

RECOGNIZE SAFETY

SYMBOLS, WORDS,

LABELS

1. Read all instructions before using the refrigerator.

2. Observe all local codes and ordinances.

3. Be sure to follow grounding instructions.

4. Check with a qualified electrician if you are not sure this

appliance is properly grounded.

5. DO NOT ground to a gas line.

6. DO NOT ground to a cold-water pipe.

7. Refrigerator is designed to operate on a separate 103 to

126 volt, 15 amp., 60 cycle line. DO NOT modify plug on

power cord. If plug does not fit electrical outlet, have prop-

er outlet installed by a qualified electrician.

8. DO NOT use a two-prong adapter, extension cord or power

strip.

9. DO NOT remove warning tag from power cord.

10. DO NOT tamper with refrigerator controls.

11. DO NOT service or replace any part of refrigerator unless

specifically recommended in owner’s manual or published

user-repair instructions. DO NOT attempt service if instructions

are not understood or if they are beyond personal skill level.

12. Always disconnect refrigerator from electrical supply before

attempting any service. Disconnect power cord by grasping

the plug, not the cord.

13. Install refrigerator according to Installation Instructions. All

connections for water, electrical power and grounding must

comply with local codes and be made by licensed person-

nel when required.

14. Keep your refrigerator in good condition. Bumping or drop-

ping refrigerator can damage unit or cause unit to malfunc-

tion or leak. If damage occurs, have refrigerator checked by

qualified service technician.

15. Replace worn power cords and/or loose plugs.

16. Always read and follow manufacturer’s storage and ideal

environment instructions for items being stored in refrigerator.

INSTALLATION

These instructions were provided to aid

you in the installation of your refrigerator.

Measuring the opening

This refrigerator was designed to fit a 69"

tall opening to allow for proper ventilation,

leveling and door adjustments.

Please also take into account, when

measuring space for your unit, that some

models require a certain amount of clear-

ance around it to allow for proper air flow.

Proper air flow is key to keeping your unit

running at optimum efficiency. To deter-

mine measurements, please reference

the table below.

Subflooring or floor coverings (i.e. carpet,

tile, wood floors, rugs) may make your

opening smaller than anticipated.

Some clearance may be gained by using

the leveling procedure under Leveling

Your Refrigerator.

Selecting the best

location

Observe these points when choosing the

final location for your refrigerator:

➢ DO NOT install refrigerator near oven,

radiator or other heat source. If not

possible, shield refrigerator with

cabinet material.

➢ DO NOT install where temperature

falls below 55° F (13° C). Malfunction

may occur at this temperature.

➢ To assure proper door closure, follow

the leveling instructions in the section,

Leveling Your Refrigerator.

Transporting your

refrigerator

Follow these tips when moving the refrig-

erator to final location:

➢ NEVER transport refrigerator on its

side. If an upright position is not possi-

ble, lay refrigerator on its back. Allow

refrigerator to sit upright for approxi-

mately 30 minutes prior to plugging

refrigerator in to assure oil returns to

the compressor. Plugging refrigerator

in immediately may cause damage to

internal parts.

➢ Use an appliance dolly when moving

refrigerator. ALWAYS truck refrigera-

tor from its side or back–NEVER from

its front.

➢ Protect outside finish of refrigerator

during transport by wrapping cabinet

in blankets or inserting padding

between the refrigerator and dolly.

➢ Secure refrigerator to dolly firmly with

straps or bungee cords. Thread straps

through handles when possible. DO

NOT overtighten. Overtightening

restraints may dent or damage outside

finish.

IMPORTANT: If refrigerator is to be

installed into a recess where top of

refrigerator is completely covered, use

dimensions from floor to top of hinge cap

to verify proper clearance.

Recommended

Unit Total Clearance

Volume

Top Sides Rear

Less than

N/A N/A

⁄

23 cu. ft.

Greater than

⁄

2" N/A

⁄

23 cu. ft.

INSTALLATION

, CONT.

To avoid severe personal injury or

death, observe the following:

• Disconnect power to refrigerator

before removing doors. Connect

power only after replacing doors.

• Green ground wire must be

attached to top hinge while

performing door removal and

replacement.

•Tape decorative panels (select

models) securely into place before

removing door handles.

WARNING

To avoid property damage, observe

the following:

➢ Protect soft vinyl or other flooring

with cardboard, rugs or other pro-

tective material, prior to moving

refrigerator.

➢ To avoid damage or breakage to

adjusting bolt, do not use power

tools to correct leveling.

➢ DO NOT adjust refrigerator to be

any shorter than 68

⁄

2" tall (minus

hinge and cap). Doing so may

damage underside components.

CAUTION

1. Remove toe grille and bottom hinge

covers.

➢ Open both doors 180 degrees, or

as wide as possible to remove.

2. While pinching white collar (A) to the

blue connector (B), pull water line from

connector.

4. Close doors.

5. Unscrew

⁄16" hex head screws from

top hinges.

For dispensing models only:

• DO NOT remove either green

ground wire or wire connecting

center screw.

6. For dispensing models only:

Detach main wire connector harness

and red wire harness.

➢ To detach main wire harness, use a

flat blade screwdriver or fingernail

to press junction point between two

connectors to release.

➢ To detach red wire harness, press

tab on underside of connector to

release.

7. Remove top hinges along with doors.

8. Remove bottom hinges with a

⁄8" hex

head driver.

Removing the doors

and hinges

Some installations require door removal

to get refrigerator to final location.

Replacing the doors

➢ To replace the doors, follow the steps

in Removing the Doors and Hinges

in reverse order.

IMPORTANT: When reconnecting water

line, cut off tubing at first available scored

line before inserting into connector collar.

IMPORTANT: When reconnecting water

line, cut off tubing at first available scored

line before inserting into connector collar.

3. Remove top hinge cover by removing

Phillips screw.

Installing handles

If installing handles for the first time, the

fresh food handles can be located within

the fresh food section. The handle trim

will be located in the literature pack.

➢ Remove two

⁄4" hex nut screws from

bottom of refrigerator and freezer

door.

➢ Align door handles with top and bot-

tom sets of door clips, and slide down

until screw holes on bottom of handles

match with door screw holes.

➢ Insert

⁄4" hex nut screws previously

removed into screw holes at bottom of

handle section.

➢ Snap trim over bottom portion of han-

dles and retainers on bottom of door.

Removing handles

Removing handles may be necessary

when transporting unit through tight

spaces.

➢ Remove bottom portion of handles with

a very small flat-blade screwdriver.

IMPORTANT: Wrap blade of screwdriver

with masking tape to avoid damaging

unit.

➢ Remove two handle base screws.

➢ Pull handle up and out to release from

unit. Fit may be tight.

Leveling your

refrigerator

MATERIALS NEEDED:

•

⁄8" hex head driver

• Level

➢ Remove toe grille and bottom hinge

covers (see previous instructions).

➢ Turn both front adjustment screws (A)

clockwise to raise and counterclock-

wise to lower.

➢ Turn both rear adjustment screws (B)

clockwise to raise and counterclock-

wise to lower.

➢ Protect soft vinyl or other flooring

with cardboard, rugs or other pro-

tective material, prior to moving

refrigerator.

➢ To avoid damage or breakage to

adjusting bolt, do not use power

tools to correct leveling.

➢ DO NOT adjust unit to be any

shorter than 68

⁄2" tall (minus hinge

and cap). Doing so may damage

underside components.

CAUTION

➢ Check with level to verify

⁄

4" tilt to the

back for proper door closure.

• If unit is aligned and stable, replace

toe grille and hinge covers.

INSTALLATION

, CONT.

➢ If required, correct rocking of unit by

turning rear adjustment screw clock-

wise to raise rocking corner.

➢ If doors are uneven:

• Determine which door needs to be

raised.

•Turn front roller adjustment screw

clockwise to raise front corner of

door.

• If the unit has reached the bottom

limit of its adjustment range, and

doors are still not level–lower oppo-

site door by turning roller adjust-

ment screw counterclockwise.

➢ Check with level to verify

⁄4

" tilt to the

back for proper door closure.

• If unit is aligned and stable, replace

toe grille and hinge covers.

Connecting the water

supply

MATERIALS NEEDED:

•

⁄4

" (6 mm) outer diameter flexible cop-

per tubing

• Brass nut and sleeve (see literature

pack)

• Shut-off valve

Requires a

⁄4" (6 mm) hole to be drilled

into water supply before valve attach-

ment

• Adjustable wrench

NOTE: Add 8' (2 m) to tubing length

needed to reach water supply for cre-

ation of service loop.

➢ Create service loop with tubing using

care to avoid kinks in tubing.

➢ Remove plastic cap from water valve

inlet port.

➢ Place brass nut and sleeve on copper

tube end as illustrated.

➢ Place end of copper tubing into water

valve inlet port. Shape tubing slightly –

DO NOT KINK – so that tubing feeds

straight into inlet port.

➢ Slide brass nut over

sleeve and screw nut

into inlet port. Tighten

nut with wrench. Pull on

tubing to confirm con-

nection is secure.

IMPORTANT: DO NOT overtighten.

Cross-threading may occur.

➢ Locate water tubing

clamp and install with

⁄4” hex head screw.

Turn on water supply

and check for leaks and

correct, if present.

➢ Monitor water connection for 24

hours. Correct leaks, if necessary.

Brass

Nut Sleeve

To avoid electrical shock which can

cause severe personal injury or death,

disconnect power to refrigerator

before connecting water supply.

Connect power only after connecting

water supply.

WARNING

To avoid property damage, observe

the following:

➢ Consult a plumber to connect cop-

per tubing to household plumbing

to assure compliance with local

codes and ordinances.

➢ Confirm water pressure to water

valve is between 20 and 100 PSI. If

water filter is installed, water pres-

sure to water valve must be a min-

imum of 35 PSI.

➢ DO NOT use a self-piercing, or

⁄16"

(4.8 mm) saddle valve. Both

reduce water flow, become clogged

with time, and may cause leaks if

repair is attempted.

➢ Tighten nuts by hand to prevent

cross threading. Finish tightening

nuts with pliers and wrenches. DO

NOT overtighten.

➢ Wait 24 hours before placing unit

into final position to check and cor-

rect any water leaks.

CAUTION

Setting the temperature

controls

This refrigerator is designed to operate at

a household temperature of 55° to 100° F

(13° to 43° C).

INITIAL TEMPERATURE

SETTINGS

Locate refrigerator and freezer controls

on upper-left wall of refrigerator section

and set both controls to 3

⁄2.

IMPORTANT: Neither section will cool if

freezer control is set to OFF.

Adjusting the

temperature controls

MATERIALS NEEDED:

•2 thermometers measure -5° to 50° F

(-21° to 10° C)

•2 drinking glasses

IMPORTANT: Due to design of unit,

always start temperature adjustments

with freezer section.

FREEZER

➢ Place thermometer in glass of veg-

etable oil in middle of freezer.

➢ Allow 24 hours for temperatures to

stabilize.

➢ Check to see if temperature is 0° to 2° F

(-17° to -16° C).

•Turn control to next highest number

if too warm.

•Turn control to next lowest number if

too cold.

• Allow 5 to 8 hours for adjustments to

take effect.

➢ Repeat as necessary.

REFRIGERATOR

➢ Place thermometer in glass of water in

middle of refrigerator.

➢ Allow 24 hours for temperatures to

stabilize.

➢ Check to see if temperature is 38° to

40° F (3° to 4° C).

•Turn control to next highest number

if too warm.

•Turn control to next lowest number if

too cold.

• Allow 5 to 8 hours for adjustments to

take effect.

➢ Repeat as necessary.

FRESH FOOD FEATURES

Dairy center

The dairy center provides convenient

storage for items such as butter, yogurt,

cheese, etc.

This compartment is an adjustable fea-

ture located in the door. It can be moved

to several different locations to accom-

modate storage needs.

To remove bin:

➢ Slide dairy center up and pull out.

To reinstall bin:

➢ Slide assembly in above desired door

liner retainer and push down until it

stops.

To remove dairy door:

➢ Press in sides of dairy door and pull

out.

To reinstall dairy door:

➢ Slide sides of dairy door inside dairy

center until hinge points snap into

place.

Adjustable door buckets

Door buckets adjust to meet individual

storage needs.

To remove buckets:

➢ Lift the door bucket up until it clears

the retainers on the door liner, then

pull the door bucket straight out.

To reinstall buckets:

➢ Slide bucket in above desired door

liner retainer and push down until

bucket stops.

Shelves

SEALED SHELVES

Shelves hold simple spills for easier

cleaning.

To remove shelves:

➢ Lift up and out.

To reinstall shelves:

➢ Reverse above procedure.

Select models feature sealed shelves

with a pullout design to reach items in the

back. For ease of cleaning, glass shelf

may be removed by pulling to full exten-

sion and lifting out of frame.

To remove shelf and frame:

➢ See instructions for Sealed Stationary

Shelves.

To avoid personal injury or property

damage, observe the following:

➢ Confirm shelf is secure before plac-

ing items on shelf.

➢ Handle tempered-glass shelves

carefully. Shelves may break sud-

denly if nicked, scratched or

exposed to sudden temperature

change.

CAUTION

CRISPER SHELF

To remove crisper shelf:

➢ Lift off wall supports and remove.

To reinstall crisper shelf:

➢ Lower shelf onto wall supports and

push in until shelf is flush with rear

wall.

Deli drawer

The deli drawer system provides a draw-

er with a variable temperature control that

can keep the compartment colder than

refrigerator temperature.

NOTE: Cold air directed to the deli draw-

er system can decrease refrigerator tem-

perature. Refrigerator control may need

to be adjusted.

CONTROLS

Located on the wall to the left of the draw-

er, the controls regulate the air tempera-

ture in the Deli drawer. Set control level to

cold to provide normal refrigerator tem-

perature. Use the coldest setting for stor-

ing meat, poultry or fish.

To remove drawer(s):

➢ Pull drawer out to full extension.

➢ Tilt up front of drawer and pull straight

out.

To reinstall drawer(s):

➢ Reverse above procedure.

Crisper drawer

The crisper keeps produce fresh longer

by providing an environment with

adjustable humidity.

CONTROLS

The controls regulate the amount of

humidity in the crisper drawer. Use the

low setting for non-leafy produce. Use the

high setting for leafy produce.

SETTINGS

LOW

• apples • grapes

• cauliflower • oranges

• corn • zucchini

• cucumbers

HIGH

• asparagus • fresh herbs

• broccoli • fresh sprouts

• cabbage • lettuce

• celery • spinach

Please observe the following recommen-

dations when storing produce in humidi-

ty-controlled crispers:

➢ DO NOT wash produce before placing

in crispers. Any additional moisture

added to the crispers may cause pro-

duce to prematurely spoil.

➢ DO NOT line crispers with paper tow-

els. Towels will retain moisture.

➢ Follow control instructions carefully.

Incorrect control settings may damage

produce.

To remove drawer(s):

➢ Pull drawer out to full extension.

➢ Tilt up front of drawer and pull straight

out.

To reinstall drawer(s):

➢ Reverse above procedure.

Snack drawer

(SELECT MODELS)

This drawer can be used for storage of

food items.

To remove drawer:

➢ Pull drawer out to full extension.

➢ Tilt up front of drawer and pull straight

out.

To reinstall drawer:

➢ Reverse above procedure.

FREEZER FEATURES

Shelves and baskets

To remove shelves:

➢ Remove shelf

from wall mount-

ing clips and pull

out of left side

mounting holes.

To reinstall shelves:

➢ Reverse above procedure.

Baskets slide out for easy access of

items in back.

To remove baskets:

➢ Pull basket forward to full extension.

➢ Lift front handle to release basket from

rails and remove.

To reinstall baskets:

➢ Reverse above procedure.

Chill shelf

The chill shelf provides a space for items

to be chilled or frozen quickly.

To remove:

➢ Lift chill shelf

from ice bin rails

and pull straight

out.

To reinstall:

➢ Reverse above procedure.

IMPORTANT: The chill shelf should not

be installed if ice maker arm is in “off”

position.

Door storage

ADJUSTABLE DOOR

BUCKETS

Door buckets adjust to meet individual

storage needs.

To remove buckets:

➢ Lift the door bucket up until

it clears the retainers

on the door liner,

then pull the door

bucket straight out.

To reinstall buckets:

➢ Slide bucket in above desired door

liner retainer and push down until

bucket stops.

Fixed door bucket

(SELECT MODELS)

The fixed door bucket is

located in the upper sec-

tion of the freezer door.

IMPORTANT: Fixed door bucket is not

adjustable. If bucket is removed, freezer

light will not deactivate when door is

closed.

Ice storage bin

This ice storage bin is located below the

automatic dispensing ice maker.

To remove:

➢ Remove chill shelf.

Raise ice maker

arm to deactivate

ice maker.

➢ Lift front of bin and

pull out to its full

extension. Lift up front of bin and

remove.

To reinstall:

➢ Slide bin into rails below ice maker

until bin locks into place. Drop ice

maker arm to activate ice maker, and

replace chill shelf.

To avoid possible injury, including

death, do not place glass items in chill

shelf. Glass objects may shatter or

explode if exposed to extreme cold.

WARNING

To avoid property damage, observe

the following:

➢ Do not force ice maker arm down

or up.

➢ Do not place or store anything in

ice storage bin.

CAUTION

Automatic ice maker

This ice maker creates the ice used in the

dispensing system.

Using ice maker for the first time:

➢ Confirm ice bin is in

place and ice

maker arm is down.

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker

fills with water and begins operating.

➢ Allow approximately 24 hours after

installation to receive first harvest of ice.

➢ Discard ice created within first 12

hours of operation to verify system is

flushed of impurities.

Operating instructions:

➢ Confirm ice bin is in place and ice

maker arm is down.

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker

fills with water and begins operating.

You will have a complete harvest of

ice approximately every 3 hours.

➢ Stop ice production

by raising ice

maker arm until

click is heard.

➢ Ice maker will remain in the off posi-

tion until arm is pushed down.

IMPORTANT: The chill shelf should not

be installed if ice maker arm is in “off”

position.

IMPORTANT: Ice bin must be locked in

proper place for proper ice dispensing. If

freezer door does not close, bin is not in

proper location. Turn auger driver coun-

terclockwise to

properly align ice

bin with back of

unit.

Chill

Shelf

Ice Storage

Bin

DISPENSER FEATURES

DISPENSER LIGHT

A light activates within the dispenser area

at full power when dispensing ice or

water.

Dispenser pad

The dispenser pad is located on the back

wall of the dispensing area. When the

dispenser pad is pressed, the selection

chosen on the dispenser control panel

will dispense.

NOTE:

➢ During initial use of water dispenser,

there will be a 1- to 2-minute delay

while water tank fills before water dis-

penses. Discard first 10-14 containers

of water after initially connecting

refrigerator to household water supply

and after extended periods of nonuse.

To dispense water:

➢ Choose water selection from dis-

penser control panel.

➢ Press sturdy, wide-mouthed container

against dispenser pad.

➢ Release pressure on dispenser pad to

stop water from dispensing. A small

amount of water may continue to dis-

pense and collect in dispenser tray.

Large spills should be wiped dry.

ICE DISPENSER

OPERATION

To dispense ice:

➢ Select cubed or crushed ice mode by

pushing appropriate button on

dispenser control panel. A green

indicator light above button shows

mode selection.

➢ Press container against dispenser

pad. When dispensing crushed ice,

hold container as close to chute as

possible to reduce spraying. Selection

mode may not be changed while ice

dispenser is in operation.

REMOVABLE TRAY

The removable tray at the bottom of the

dispenser area is designed to collect

small spills and may be easily removed

for cleaning and emptying purposes.

IMPORTANT: Removable tray does not

drain. Continuous water running into tray

will cause tray to overflow.

WATER DISPENSER

OPERATION

To avoid personal injury or property

damage, observe the following:

➢ DO NOT put fingers, hands or any

foreign object into dispenser opening.

➢ DO NOT use sharp objects to

break ice.

➢ DO NOT dispense ice directly into

thin glass, fine china or delicate

crystal.

CAUTION

FILTRATION SYSTEM

(SELECT MODELS)

Water filter removal and

installation

Initial installation of

water filter

➢ Remove blue bypass cap and retain

for later use.

➢ Remove sealing label from end of filter

and insert into filter head.

•Rotate gently clockwise until filter

stops and snap filter cover closed.

➢ Reduce water spurts by flushing air

from system. Run water continuously

for 2 minutes through dispenser until

water runs steady.

• Additional flushing may be required

in some households where water is

of poor quality.

Replacing water filter

IMPORTANT: Air trapped in system may

cause water and cartridge to eject. Use

caution when removing.

➢ Turn filter counterclockwise until it

releases from filter head.

➢ Drain water from filter into sink and

dispose in normal household garbage.

➢ Wipe up excess water in filter cover.

➢ Remove sealing label from end of filter

and insert into filter head.

•Rotate gently clockwise until filter

stops and snap filter cover closed.

➢ Reduce water spurts by flushing air

from system. Run water continuously

for 2 minutes through dispenser until

water runs steady.

• Additional flushing may be required

in some households where water is

of poor quality.

When do i change the

water filter?

Filter should be changed every 6 months.

IMPORTANT: Condition of water and

amount used determines life span of

water filter cartridge. If water use is high,

or if water is of poor quality, replacement

may need to take place more often.

How do i order a

replacement filter

cartridge?

To order a replacement filter cartridge

model OWF51 (part no. 12589210), or for

service, contact your local dealer or

Maytag Appliances Sales Company,

Maytag Customer Assistance, U.S.:

1-877-232-6771.

I’m trying to dispense

water to flush the

system. where’s the

water?

During initial use, allow about a 1- to 2-

minute delay in water dispersal to allow

internal water tank to fill.

What if i choose not to

use the water filtration

system?

Dispenser feature may be used without

water filter cartridge. If you choose this

option, replace filter with blue bypass

cap.

➢ Bypass cap DOES NOT filter

water. Be sure to have replacement

cartridge available when filter

change is required.

➢ If water filtration system has been

allowed to freeze, replace filter car-

tridge.

➢ If system has not been used for

several months, and water has an

unpleasant taste or odor, flush sys-

tem by dispensing 2-3 glasses of

water. If unpleasant taste or odor

persists, change filter cartridge.

CAUTION

To avoid serious illness or death, do

not use unit where water is unsafe or

of unknown quality without adequate

disinfection before or after use of filter.

WARNING

WATER FILTER DATA

(SELECT MODELS)

GENERAL USE

CONDITIONS

Read this Performance Data Sheet and

compare the capabilities of this unit with

your actual water treatment needs.

DO NOT use this product where water

is microbiologically unsafe or of

unknown quality without adequate

disinfection before or after the sys-

tem. System certified for cyst reduc-

tion may be used on disinfected water

that may contain filterable cysts.

Use only with cold water supply.

Check for compliance with the state

and local laws and regulations.

The retractable water filtration system

uses a OWF51 replacement cartridge.

Timely replacement of filter cartridge is

essential for performance satisfaction

from this filtration system. Please refer to

the applicable section in this owner’s

manual for general operation, mainte-

nance requirements and troubleshooting.

Replacement Elements: OWF51

This system has been tested according to

ANSI/NSF 42 and 53 for reduction of the

substances listed below. The concentra-

tion of the indicated substances in water

entering the system was reduced to a

concentration less than or equal to the

permissible limit for water leaving the sys-

tem, as specified in ANSI/NSF 42 and 53.

*Tested using a flow rate of 0.75 GPM (2.83 L/min.) and a maximum pressure of 120 psi (827 kPa) under

standard laboratory conditions, however, actual performance may vary. Health Claim Performance test-

ed and certified by NSF International

** Particle size range classification of test. Particles used were 0.5 –1 microns.

Influent Challenge Effluent Average % Maximum Min. Required Inlet

Substance Concentration Average Reduction Effluent Reduction pH

Lead 0.15 mg/L +/- 10% 0.001 mg/L 99.33% 0.001 mg/L 0.010 mg/L 6.5

Lead 0.15 mg/L +/- 10% 0.002 mg/L 98.66% 0.003 mg/L 0.010 mg/L 8.5

Cyst Minimum 50,000/L 1count/mL 99.99% 3 count/mL > 99.95% NA

Turbidity 11+/-1 NTU 0.12 NTU 98.98% 0.18 NTU 0.5 NTU NA

Lindane 0.002 mg/L +/- 10% 0.00005 mg/L 97.62% 0.00005 mg/L 0.00002 mg/L NA

Atrazine 0.009 mg/L +/- 10% 0.0002 mg/L 97.93% 0.0006 mg/L 0.003 mg/L NA

Chlorine 2.0 mg/L +/- 10% 0.09 mg/L 95.26% 0.17 mg/L ≥75% NA

Particulate** at least 10,000 900 count/mL 99.68% 2400 count/mL ≥85% NA

particles/mL

2,4-D 0.210 mg/L +/- 10% 45.45 ug/L 84.42% 100 ug/L 0.0017 mg/L NA

Asbestos

to 10

fibers/L; fibers greater

0.16 MFL/mL 99.96% 0.16 MFL/mL 99% NA

than 10 micrometers in length

PERFORMANCE DATA

SYSTEM SPECIFICATION AND PERFORMANCE DATA

SHEET REFRIGERATOR WATER FILTER CARTRIDGE

MODEL OWF51

Specifications

Service Flow Rate (maximum) ...............................................0.75 GPM (2.83 L/min)

Rated Service Life OWF50-NI300 (maximum) ......................300 gallons (1135 liters)

Rated Service Life OWF50-WI500 (maximum)......................500 gallons (1892 liters)

Maximum Operating Temperature..........................................100° F (38° C)

Minimum Operating Temperature...........................................33° F (1° C)

Minimum Pressure Requirement............................................35 psi (138 kPa)

Maximum Operating Pressure ...............................................120 psi (827 kPa)

1000 Apollo Road

Eagan, Minnesota U.S.A.

EPA EST #35917-MN-1

Standard No. 53: Health Effects

Chemical Reduction Unit

Lead, Atrazine, Lindane and 2, 4-D Reduction

Mechanical Filtration Unit

Cyst, Turbidity and Asbestos Reduction

Tested and certified by NSF International against ANSI/NSF Standards 42 and 53 in

models OWF50-WI500 and OWF50-NI300 for the reduction of:

Standard No. 42: Aesthetic Effects

Taste and Odor Reduction

Chlorine Reduction

Mechanical Filtration Unit

Particulate Reduction Class 1

CARE AND CLEANING

PART DO

➢ Use 4 tablespoons of baking soda dissolved in 1 quart (1 liter)

warm soapy water.

➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ Use warm, soapy water and a soft, clean cloth or sponge.

➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ Use a vacuum cleaner hose nozzle.

➢ Use a vacuum cleaner hose nozzle with brush attachment.

➢ Follow removal and installation instructions from appropriate

feature section.

➢ Allow items to adjust to room temperature.

➢ Dilute mild detergent and use a soft clean cloth or sponge for

cleaning.

➢ Use a plastic bristle brush to get into crevices.

➢ Rinse surfaces with clean warm water.

➢ Dry glass and clear items immediately to avoid spots.

DO NOT USE

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Vinegar-based products

➢ Citrus-based cleaners

➢ Abrasive or harsh cleaners

➢ Metal or plastic-textured

scouring pads

➢ A dishwasher

Textured Doors

and Exterior

Cabinet Interior

Stainless Steel Doors

and Exterior

IMPORTANT: Damage

to stainless steel finish

due to improper use of

cleaning products or

non-recommended

products is not covered

under this product’s

warranty.

Door Gaskets

Condenser Coil

Remove base grille to

access

Condenser Fan Outlet

Grille

See back of refrigerator

Accessories Shelves,

buckets, drawers, etc.

To avoid personal injury or property damage, observe the following:

• Read and follow manufacturer’s directions for all cleaning products.

• DO NOT place buckets, shelves or accessories in dishwasher. Cracking or warp-

ing of accessories may result.

CAUTION

To avoid electrical shock which can

cause severe personal injury or death,

disconnect power to refrigerator

before cleaning. After cleaning, con-

nect power.

WARNING

Removing odors from

refrigerator

➢ Remove all food.

➢ Disconnect refrigerator.

➢ Clean the following items using the

appropriate instructions in the Care

and Cleaning table.

–Walls, floor and ceiling of cabinet

interior

– Drawers, shelves and gaskets

according to the instructions in this

section.

➢ Pay special attention to clean all

crevices by completing the following

steps.

– Dilute mild detergent and brush

solution into crevices using a plas-

tic bristle brush.

– Let stand for 5 minutes.

– Rinse surfaces with warm water.

Dry surfaces with a soft, clean

cloth.

Energy saving ideas

➢ Avoid overcrowding refrigerator

shelves. This reduces effectivity of air

circulation around food and causes

refrigerator to run longer.

➢ Avoid adding too much warm food to

unit at one time. This overloads com-

partments and slows rate of cooling.

➢ Do not use aluminum foil, wax paper,

or paper toweling as shelf liners. This

decreases air flow and causes unit to

run less efficiently.

➢ A freezer that is

⁄3 full runs most effi-

ciently.

➢ Locate refrigerator in coolest part of

room. Avoid areas of direct sunlight, or

near heating ducts, registers or other

heat producing appliances. If this is

not possible, isolate exterior by using

a section of cabinet or an added layer

of insulation.

➢ Refer to Owner's Manual section on

temperature controls for recommend-

ed control settings.

➢ Clean door gaskets every three

months according to Owner's Manual

cleaning instructions. This will assure

that door seals properly and unit runs

efficiently.

➢ Take time to organize items in refriger-

ator to reduce time that door is open.

➢ Be sure your doors are closing

securely by leveling unit as instructed

in this Owner's Manual (see page 4).

➢ Clean condenser coils as indicated in

the Owner's Manual every 3 months.

This will increase energy efficiency

and cooling performance.

➢ Wash and dry all bottles, containers

and jars. Discard spoiled or expired

items.

➢ Wrap or store odor-causing foods in

tightly sealed containers to prevent

reoccurring odors.

➢ Connect power to refrigerator and

return food to unit.

➢ After 24 hours, check if odor has been

eliminated.

If odor is still present:

➢ Remove drawers and place on top

shelf of refrigerator.

➢ Pack refrigerator and freezer sections

– including doors – with crumpled

sheets of black and white newspaper.

➢ Place charcoal briquettes randomly on

crumpled newspaper in both freezer

and refrigerator compartments.

➢ Close doors and let stand 24-48

hours.

CARE AND CLEANING

, CONT.

Lower fresh food section

This light is also found in the freezer

section if the model does not have an ice

and water dispenser.

NOTE: Before removing freezer light

cover, remove all surrounding shelving

using instructions in the Freezer Features

section.

➢ Pinch bottom tabs (A) on light cover

and pull straight out.

➢ Remove light bulb.

➢ Replace bulb with appliance bulb no

greater than 40 watts.

➢ Insert top tabs (B) of light cover into

refrigerator liner and snap bottom por-

tion over light assembly.

Freezer section

(DISPENSER MODELS ONLY)

➢ Remove ice bin by lifting front of bin

and pulling out.

➢ Remove light bulb cover by pinching

top tab (A) and pulling cover out of

liner.

➢ Replace bulb with appliance bulb no

greater than 40 watts.

➢ Insert top tabs (B) of light cover into

refrigerator liner and snap bottom por-

tion over light assembly.

➢ Replace ice bin by sliding in until bin

locks into place.

ice and water dispenser

➢ Locate light bulb inside top edge of

dispenser frame. Unscrew to remove.

➢ Replace light bulb with a 7 watt, 120 volt

bulb.

To avoid personal injury or property

damage, observe the following:

➢ Allow light bulb to cool.

➢ Wear gloves when replacing light

bulb.

CAUTION

To avoid electrical shock which can

cause severe personal injury or death,

disconnect power to refrigerator

before replacing light bulb. After

replacing light bulb, connect power.

WARNING

Remove and replace

light bulbs

Upper fresh food

section

➢ Locate finger gaps on each side of

clear light shield. Insert fingers and

press in on each side of shield. Pull

shield down and remove.

➢ Remove light bulbs.

➢ Replace with appliance bulbs no

greater than 40 watts.

➢ Replace light bulb cover by inserting

front tabs of light shield into holes in

liner directly in front of light assembly.

➢ Snap back of light cover into place.

NORMAL OPERATING SOUNDS

Today’s refrigerators have new features and are more energy efficient. Foam insulation is very energy efficient and has excellent insu-

lating capabilities, however, foam insulation is not as sound absorbent. As a result, certain sounds may be unfamiliar. In time, these

sounds will become familiar. Please refer to this information before calling service.

SOLUTION

➢ Normal operation

➢ See Installation Instructions for details on how to level your

unit.

➢ Normal operation

➢ Stop sound by raising ice maker arm to ‘off’ position. See

Automatic Ice Maker section in your owner’s manual for

details.

➢ Normal operation

POSSIBLE CAUSE

➢ Freezer control (A) clicks when

starting or stopping compressor.

➢ Defrost timer (B) sounds like an

electric clock and snaps in and

out of defrost cycle.

➢ Freezer fan (C) and condenser

fan (D) make this noise while

operating.

➢ Evaporator (E) and heat

exchanger (F) refrigerant makes

this noise when flowing.

➢ Ice cubes from ice maker (select

models) drop into ice bucket (G).

➢ Dispenser ice chute (H) closing.

➢ Compressor (I) makes a

pulsating sound while running.

➢ Refrigerator is not level.

➢ Ice maker water valve (J)

hookup (select models) buzzes

when ice maker fills with water.

➢ Ice maker (K) is in the ‘on’ posi-

tion without water connection.

➢ Ice auger (L) (select models)

hums as auger agitates ice

during dispensing.

➢ Compressor (I) can make a high-

pitched hum while operating.

➢ Solenoid valve (M) operating

ice chute door.

TOPIC

Clicking

Air rushing or whirring

Gurgling or boiling

sound

Thumping

Vibrating noise

Buzzing

Humming

BEFORE YOU CALL FOR SERVICE

PROBLEM POSSIBLE CAUSES WHAT TO DO

Freezer control and lights Refrigerator is in defrost mode. Normal operation. Wait 40 minutes to see if refrigerator restarts.

are on, but compressor

is not operating

Deli drawer temperature Control settings are too low. See section on Deli drawer to adjust controls.

is too warm

Freezer controls are set too low. See controls section in Installation on how to adjust your

controls.

Drawer is improperly positioned. See section on Deli drawer in Fresh Food Features to verify

drawer positioning.

Refrigerator does not Refrigerator is not plugged in. Plug in unit.

operate

Freezer control is not on. See controls section in Installation on how to adjust your

controls.

Fuse is blown, or circuit breaker needs to be Replace blown fuses. Reset circuit breaker.

reset.

Power outage has occurred. Call local power company listing to report outage.

Refrigerator still won’t Unit is malfunctioning. Unplug refrigerator and transfer food to another unit. If another

operate unit is not available, place dry ice in freezer section to preserve

food. Warranty does not cover food loss.

Contact service for assistance.

Food temperature Condenser coils are dirty. Clean according to care and cleaning instructions.

is too cold

Refrigerator or freezer controls are set too high. See Installation section on how to adjust controls.

Food temperature Door is not closing properly. Refrigerator is not level. See Installation Instructions.

appears too warm

Check gaskets for proper seal. Clean, if necessary.

Check to see if something is preventing door from closing.

Controls need to be adjusted. See Installation section on how to adjust controls.

Condenser coils are dirty. Clean according to cleaning instructions. See page 13.

Rear air grille is blocked. Check the positioning of food items in refrigerator to make sure

grille is not blocked. Rear air grilles are located under crisper

drawers.

Prolonged door openings. Minimize door openings.

Refrigerator has an odor Compartment is dirty or has odor-causing food. See Care and Cleaning section.

Water droplets form on Check gaskets for proper seal. See cleaning guide in Care and Cleaning section.

outside of refrigerator

Humidity levels are high. Normal during times of high humidity.

Controls require adjustment. See Installation section on how to adjust controls

Water droplets form on Humidity levels are high or door has been See Installation section on how to adjust controls.

inside of refrigerator been opened frequently.

Check gaskets for proper seal. Minimize door openings. Organize food items efficiently to

assure door is open for as short a time as possible.

See cleaning guide in Care and Cleaning section.

Noise, sounds and Normal operation. See Normal Operating Sounds.

vibrations

Cabinet not level. Level cabinet.

Deli/Crisper drawers do not Contents of drawer, or positioning of items Reposition food items and containers to avoid interference with

close freely in the surrounding compartment could be the drawers.

obstructing drawer.

Drawer is not in proper position. See Fresh Food section to verify drawer.

Refrigerator is not level. See Installation Instructions.

Drawer channels are dirty or need treatment. Clean drawer channels with warm, soapy water. Rinse and dry.

Apply a thin layer of petroleum jelly to drawer channels.

Refrigerator runs too Doors have been opened frequently or for Minimize door openings. Organize food items efficiently to

frequently long periods of time. assure door is open for as short a time as possible.

Humidity or heat in surrounding area is high. Normal operation.

Food has recently been added. Allow time for recently added food to reach refrigerator or

freezer temperature.

Unit is exposed to heat by environment or Evaluate your unit’s environment. Unit may need to be moved

by appliances nearby. to run more efficiently.

Condenser coils are dirty. See Care and Cleaning section.

Controls need to be adjusted. See Installation.

Door is not closing properly. Refrigerator is not level. See Installation Instructions.

Check gaskets for proper seal. Clean, if necessary.

Check to see if something is preventing door from closing.

Review this chart of troubleshooting tips first…you may not need to call for service at all.

Ice and Water

PROBLEM POSSIBLE CAUSES WHAT TO DO

Water appears cloudy Air or air bubbles in water. This is normal when first using dispenser and will disappear with use.

Particles in water and/or Carbon dust from water filter cartridge. Initial water ejected through cartridge may contain harmless carbon

ice cubes dust flushed from cartridge. Particles are safe for consumption. Will

disappear after the first few uses.

Concentrations of minerals in water will form Particles are not harmful and naturally occur in water supplies.

particles when water becomes frozen and melts.

No indicator lights are lit Freezer door is not closed. Verify that freezer door is closed. Power is removed from the control

on dispenser control when freezer door is opened.

(select models)

Refrigerator is not plugged in. Plug in unit.

Fuse is blown, or circuit breaker needs to be reset. Replace any blown fuses. Check circuit breakers for any tripped circuits.

Power outage has occurred. Call local power company listing to report outage.

Neither ice nor water is Freezer door is not closed. Verify that freezer door is closed. Power is removed from the control

dispensed when pads are when freezer door is opened.

pushed (select models)

Water tank is filling. At initial use, there is an approximate 45-second delay in dispensing

while the internal water tank is filling.

Ice maker or ice maker-equipped unit has just Wait 24 hours for ice production to begin and for ice maker to

recently been installed or a large amount of ice restock after emptied.

has just been used.

Water filter is clogged or needs to be changed. Change water filter.

Ice maker is not producing Ice maker has just recently been installed Wait 24 hours for ice production to begin and for ice maker to

enough ice or ice is or a large amount of ice has just been used. restock after emptied.

malformed (select models)

Water pressure is too low. Low water pressure can cause valve to leak. Water pressure must be

between 20 to 100 pounds per square inch to function properly. A

minimum pressure of 35 pounds per square inch is recommended for

units with water filters.

Water filter is clogged or needs to be changed. Change water filter.

Improper water valve was installed. Check water connection procedure in your Installation Instructions. Self-

piercing and

⁄16” saddle valves cause low water pressure and may

clog the line over time. The manufacturer is not responsible for property

damage due to improper installation or water connection.

Ice maker is not producing Ice maker arm is not in correct position. Confirm ice maker arm is down. See Freezer Features section in your

ice (select models) owner’s manual for details.

Household water supply is not reaching water valve. Check water connection procedure in your Installation Instructions.

Copper or plastic tubing has kinks. Turn off water supply and remove kinks. If kinks cannot be removed,

replace tubing.

Water pressure is too low. Water pressure must be between 20 to 100 pounds per square

inch to function properly. A minimum pressure of 35 pounds per

square inch is recommended for units with water filters.

Check freezer temperature. See the controls section in your owner’s manual for assistance

on how to adjust your controls. Freezer must be between 0 to

2° F (-18 to –17° C) to produce ice.

Ice bin is not installed properly. See Ice Bin section for proper installation and alignment.

Unit is leaking water Plastic tubing was used to complete water The manufacturer recommends using copper tubing for installation.

connection. Plastic is less durable and can cause leakage. The manufacturer is

not responsible for property damage due to improper installation

or water connection.

Improper water valve was installed. Check water connection procedure in your Installation Instructions. Self-

piercing and

⁄16” saddle valves cause low water pressure and may clog

the line over time. The manufacturer is not responsible for property

damage due to improper installation or water connection.

Ice forms in inlet tube to Water pressure is low. Water pressure must be between 20 to 100 pounds per square

ice maker inch to function properly. A minimum pressure of 35 pounds per

square inch is recommended for units with water filters.

Freezer temperature is too high. See controls section in chapter called Installing Your Refrigerator on

how to adjust your controls. Freezer is recommended to be between

0 to 2° F (-18 to –17° C).

Water flow is slower than Water pressure is low. Water pressure must be between 20 to 100 pounds per square

normal inch to function properly. A minimum pressure of 35 pounds per

square inch is recommended for units with water filters.

Improper water valve was installed. Check water connection procedure in your Installation Instructions. Self-

piercing and

⁄16” saddle valves cause low water pressure and may clog

the line over time. The manufacturer is not responsible for property

damage due to improper installation or water connection.

Copper or plastic tubing has kinks. Turn off water supply and remove kinks. If kinks cannot be removed,

replace tubing.

Water filter is clogged or needs to be changed. Change water filter.

Dispenser water is not cold Refrigerator has been recently installed. Allow approximately 12 hours for water in holding tank to chill.

Water supply in holding tank has been depleted.

Water has settled into water lines outside holding Discard first glass of water and refill.

tank and has warmed to room temperature.

Refrigerator warranty What is not covered by these warranties:

1. Conditions and damages resulting from any of the following:

a. Improper installation, delivery or maintenance.

b. Any repair, modification, alteration or adjustment not authorized by the

manufacturer or an authorized servicer.

c. Misuse, abuse, accidents or unreasonable use.

d. Incorrect electric current, voltage or supply.

e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed,

altered, or cannot be readily determined.

3. Light bulbs.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to:

a. Correct installation errors.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to the servicer.

6. Consequential or incidental damages sustained by any person as a result

of any breach of these warranties. Some states do not allow the exclusion

or limitation of consequential or incidental damages, so the above exclu-

sion may not apply.

To purchase accessories or replacement parts not covered by your

product warranty:

Please have your model and serial numbers ready and call our parts

specialists at 1-877-232-6771 inside U.S.A. from 7 a.m. to 7 p.m. central

time Monday through Friday. Outside the U.S.A., contact your local

appliance dealer or parts distributor.

If you need service

❚ Call the dealer from whom your appliance was purchased or call Maytag

Appliances Sales Company, Maytag Customer Assistance at 1-800-688-

9900, USA or 1-800-688-2002 Canada to locate an authorized servicer.

❚ Be sure to retain proof of purchase to verify warranty status. Refer to

WARRANTY for further information on owner’s responsibilities for

warranty service.

❚ If the dealer or service company cannot resolve the problem, write to

Maytag Appliances Sales Company, Attn: CAIR

Center, P.O. Box 2370,

Cleveland, TN 37320-2370, or call 1-800-688-9900 U.S.A. or 1-800-688-

2002 Canada.

U.S. customers using TTY for deaf, hearing impaired or speech impaired,

call 1-800-688-2080.

NOTE: When writing or calling about a service problem, please include

the following information:

a. Your name, address and telephone number;

b. Model number and serial number;

c. Name and address of your dealer or servicer;

d. A clear description of the problem you are having;

e. Proof of purchase (sales receipt).

NOTE: Some Reverse Osmosis home water systems cause low water

pressure. Low water pressure can affect the water and ice dispensing sys-

tem by causing small or hollow ice cubes and slow water flow from the dis-

penser. Service problems related to the home’s Reverse Osmosis water

system are not covered by the warranty.

Full One Year Warranty

For one (1) year from the date of original retail

purchase, any part that fails in normal home

use will be repaired or replaced free of charge.

Ice Maker - When purchased with the refriger-

ation and installed by the dealer, the ice maker

will be considered part of the refrigerator for

warranty purposes.

Limited Warranty - Major Refrigeration

Components

Second Through Fifth Year - After the first

year from the date of original purchase,

through the fifth year, the manufacturer will

repair or replace, at its option, free of charge

for parts and labor, any part of the sealed

refrigeration system (consisting of the com-

pressor, evaporator, condenser, drier and con-

necting tubing) and the cabinet liner (exclusive

of the door liner) which fail in normal home use.

Mileage and transportation charges, if

required, shall be the responsibility of the

owner.

Please note: The full warranty and the limited

warranties apply when the refrigerator is locat-

ed in the United States or Canada.

Refrigerators located elsewhere are covered

by the limited warranties only including parts

that fail during the first year.

Limitations of Liability

The warrantor shall not be liable for any inci-

dental or consequential damages, including

food loss. Some states do not allow the exclu-

sion or limitation of consequential damages, so

the above limitation or exclusion may not apply

to you.

The specific warranties expressed above are

the ONLY warranties provided by the manufac-

turer. These warranties give you specific

legal rights, and you may also have other rights

which vary from state to state.

La page charge ...

1 / 1

Maytag MCS 67002813 Le manuel du propriétaire

Marque: Maytag

Modèle: MCS 67002813

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

Ajouter aux favoris

rapport

dans d''autres langues

English: Maytag MCS 67002813 Owner's manual
español: Maytag MCS 67002813 El manual del propietario

Maytag MCS 67002813 Le manuel du propriétaire

Maytag MCS 67002813 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents