Watts Industries WFHTRF-HC Manuel utilisateur

WFHTRF-HC

2

3

USER GUIDE GB

RF Digital H&C Thermostat 4-18

GUIDE UTILISATEUR F

Thermostat Digital H&C RF 20-34

HANDLEIDING NL

Digitale thermostaat RF H&C 36-50

BEDIENUNGSANLEITUNG D

H&C Funk LCD Raumthermostat 52-68

MANUALE D’USO I

Termostato H&C LCD RF 70-86

4

PRESENTATION

- Radio Frequency “RF” thermostat (433,92Mhz)

specially designed to control the Heat&Cool

changeover of your WFHCRF-HC.

- Possibility to regulate the main room:

o Air sensor only

o Floor sensor only

o Air & Floor combined with floor sensor use

as limiter.

KEYBOARD

Navigation key left and minus key (-◄)

Validation key and mode key (OK)

Navigation key right and plus key (►+)

5

DISPLAY

1: Operating mode menu (active mode is framed).

2: Heating demand indication.

3: Cooling demand indication.

4: Batteries weak.

5: If lit-up “6” displays the measured temperature.

6: Measured temperature or setting temperature.

7: °C or °F indicator.

8: Moving bars when transmitting a radio signal

Or Title for installation Parameters (rF,

J0,CLr…)

8

7

6

1

2

3

4

5

6

MODE DESCRIPTION

Use the (OK) key to change the mode in the

Operating mode menu. (The active mode is framed)

OFF mode:

Use this mode if the zone managed by the

thermostat needs to be turned OFF.

The display will be turned off and all parameters are

saved.

COMFORT operating mode:

The comfort temperature will be followed all the

time. By pressing keys (-◄) or (►+) the comfort

temperature starts to blink and can be adjusted.

The measured temperature reappears after a

few seconds.

7

REDUCED operating mode:

The comfort temperature will be followed all the

time. By pressing (-◄) or (►+) keys the reduced

temperature starts to blink and can be adjusted.

The measured temperature (OK) reappears after a

few seconds.

Heat & Cool mode:

Use this mode to choose the working mode of the

installation. By pressing (-◄) or (►+) keys the

working mode starts to blink and can be adjusted.

Hot:

The installation will work in heating mode (Winter)

Cld:

The installation will work in cooling mode (Summer)

8

TECHNICAL CHARACTERISTICS

Measured temperature

precision

0.1°C

Operating temperature

0°C - 50°C

Setting temperature

range

5°C – 37°C by 0.5°C step

Regulation

characteristics

Proportional Integral

regulation (PWM) (adjustable

see installation menu)

Electrical Protection

Class II - IP30

Power Supply

Battery operated life

2 x 3V (CR2430)

~ 2 years

Radio frequency

433.92 MHz, <10mW.

9

Norms and

homologation:

Your thermostat has been

designed in conformity with

the following standards or

other normative

documents:

EN 60730-1 : 2003

EN 61000-6-1 : 2002

EN 61000-6-3 : 2004

EN 61000-4-2 : 2001

EN300220-1/2

EN301489-1/3

R&TTE 1999/5/EC

Low voltage 2006/95/CE

EMC 2004/108/CE

Soft version

V 4.xx

10

INSTALLATION PARAMETERS MENU

Press the (OK) key during 5 seconds, then use (-◄)

or (►+) to select the installation parameter to be

adjusted.

Press (OK) to toggle the parameter setting or edit

the value.

If the value starts to blink you can use (-◄) or (►+)

keys to adjust this value.

Press (-◄) or (►+) keys at the same to reset this

value to the factory default value. Once you have

adjusted the value press (OK) to validate this

parameter value.

11

PARAMETERS

Default value & other possibilities

rF: Radio configuration mode (see the

corresponding section).

Press (OK) on this parameter to exit the

parameters menu end come back to the main

display.

JO: Type of degrees displayed

°C Celsius

°F Fahrenheit

J5: Anti-lock-braking function of the pump when

the pump hasn’t worked on a particular day, start it

up for one minute each day:

Pmp Function activated

no Function deactivated

J6: Selection of the sensor used for the regulation:

12

Air: Room sensor only or room sensor with

floor limitation if the external sensor is

connected.

Flr: External sensor only without

limitations.

A0: Calibration of the internal sensor

(The calibration must be done after 12Hours

working with the same setting temperature)

- To check the temperature in the room, put a

thermometer at 1.5M distance to the floor in the

concerned room and wait 1 hour to be sure that

the thermometer show the correct temperature.

Then you can enter the value saw on the

thermometer with (-◄) or (►+) keys.

F0: Calibration of the external sensor.

The calibration must be done same as described

above if the external sensor is connected and

13

used like an external ambiance sensor.

If the external sensor is used as floor sensor, the

thermometer should be put on the floor.

FL: Lower limitation of the floor temperature. Only

effective if the external sensor is connected and

selected:

5°C Adjustable From 5°C to „FH“

FH: Upper limitation of the floor temperature. Only

effective if the external sensor is connected and

selected:

28°C Adjustable From „Fl“ to 37°C

J7: Selection of regulation type:

rEg: Proportional band (PWM)

hys: Static differential of 0.3°K

CY: Proportional Integral regulation time cycle

value in minutes:

14

15 slow systems adapted to the regulation of

actuators.

on: Minimum starting time in minute

02 Adjustable 0 to CY /2

Of: Minimum off time between 2 regulation cycles

02 Adjustable 0 to CY /2

Bp: Value of the proportional band in °C:

2.0 °C Adjustable 1°C to + 7°C

* This value must be adjusted by a specialist.

Cp: Value of the compensation in °C:

0.0°C Adjustable 1°C to 8°C

* This value must be adjusted by a specialist.

Clr: All parameters are reloaded with default

setting values.

End: Press on the (OK) key to exit the parameter

menu.

15

„RF“ CONFIGURATION

The WFHTRF-HC was designed to manage the

Heat & Cool changeover of your installation.

First of all, turn off your thermostat.

The RF installation will be split in two parts.

1- Standard RF initialisation (Zone

control)

To learn (*) the RF thermostat with the receiver

you must put the receiver in “RF init” mode

(please refer to the receiver leaflet).

On the receiver, choose the zones which must be

managed by the WFHTRF-HC.

16

Once, on the thermostat you have just pressed

on the (OK) key during 5 sec, then the display

„RF“ must be appears.

The thermostat sends its configuration address by

radio signal.

o The thermostat will send now the RF signal to

the receiver. Check on the receiver the good

configuration.

o If the RF learning is not made correctly, check

the installation (antenna connection, supply

voltage...)

o If the RF learning between the thermostat and

the receiver is good, put your thermostat in the

off mode

o On the receiver you can exit the “RF init” mode

or configure another standard thermostat.

(Please refer to the receiver leaflet for this)

17

2- MASTER HC RF initialisation

To learn (*) the RF thermostat with the receiver

you must put the receiver in “MHC init” mode

(please refer to the receiver leaflet).

Once, on the thermostat you have just pressed

on the (OK) key during 5 sec, then the display

„RF“ must be appears.

o The thermostat will send now the RF signal to

the receiver. Check on the receiver the good

configuration.

o On the receiver you can exit the “MHC init”

mode.(Please refer to the receiver leaflet for

this)

Now you can check the RF distance, go to the

room which must be regulated. Put your

thermostat on the final position (On the wall),

18

then put the thermostat on the heating Hot mode

(setting temperature position 37°C). Close the

door and go to the receiver to check if the new

status of the thermostat has received.

o If it’s good, adjust your setting temperature as

you want.

o If it’s not good, check the installation (Antenna

position, distance...)

* To make the installation easier it will be better to

have the thermostat near to the receiver in learning

mode.

* Only one WFHTRF-HC thermostat must be

installed on the master WFHCRF-HC to manage

the heating & cooling change over.

19

20

PRESENTATION

- Thermostat Radio Fréquence (433,92 Mhz),

destiné au control du changement de Chaud à Froid

de votre installation.

- Possibilité de réguler sur :

o Sonde ambiance seule

o Sonde sol seule

o Ambiance et sonde de sol combinées.

Dans ce cas là la sonde de sol est

généralement utilisée en limitation.

CLAVIER

Navigation touche gauche et touche - (-◄)

Touche de validation et touche mode (OK)

Navigation touche droite et touche + (►+)

La page charge ...

Watts Industries WFHTRF-HC Manuel utilisateur

Watts Industries WFHTRF-HC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents