RADSON 51044 Manuel utilisateur

51044 - Tempco Clock RF

USER GUIDE GB

GUIDE D’UTILISATION

3-25

FR

BEDIENUNGSANLEUTUNG

26-48

DE

Handleiding

50-70

NL

72-93

2

3

IMPORTANT!

Before starting work the installer should carefully read this

Installation & Operation Manual, and make sure all

instructions contained therein are understood and

observed.

- The device should be mounted, operated and maintained

by specially trained personnel only. Personnel in the

course of training are only allowed to handle the product

under the supervision of an experienced fitter. Subject to

observation of the above terms, the manufacture shall

assume the liability for the equipment as provided by legal

stipulations.

- All instructions in this Installation & Operation manual

should be observed when working with the controller. Any

other application shall not comply with the regulations. The

manufacturer shall not be liable in case of incompetent use

of the control. Any modifications and amendments are not

allowed for safety reasons. The maintenance may be

performed by service shops approved by the manufacturer

only.

- The functionality of the controller depends on the model

and equipment. This installation leaflet is part of the

product and has to be obtained.

APPLICATION

- The UFH thermostat is developed to control and manage

actuators mounting on the manifold.

- The thermostat is normally used in conjunction with a 1

zone receiver (Wall or Flush version) or a Basic Master unit

to drive actuators.

- The controllers have been designed for use in residential

rooms, office spaces and industrial facilities.

Verify that the installation complies with existing regulations

before operation to ensure proper use of the installation.

4

SAFETY INSTRUCTIONS

Before starting work disconnect power supply!

- All installation and wiring work related to the thermostat

must be carried out only when de-energized. The appliance

should be connected and commissioned by qualified

personnel only. Make sure to adhere to valid safety

regulations.

- The thermostats are neither splash- nor drip-proof.

Therefore, they must be mounted at a dry place.

- Do not interchange the connections of the sensors and

the 230V connections under any circumstances!

Interchanging these connections may result in life

endangering electrical hazards or the destruction of the

appliance and the connected sensors and other

appliances.

5

Table of content

1 Presentation ..................................................... 6

1.1 Keyboard.......................................................... 7

1.2 Display ............................................................. 8

2 First Installation ................................................ 9

2.1 Batteries installation ......................................... 9

2.2 Time and Date adjustment ............................... 9

3 RF installation ................................................ 10

3.1 RF Installation with one zone wall receiver ... 10

3.2 RF Installation with one zone flush receiver ... 10

10

3.3 RF Installation with 6 zones Master ............... 11

3.4 1 zone RF clock installation ........................... 11

3.5 Starting........................................................... 12

4 Working mode definition................................. 13

4.1 Manual mode Comfort .................................. 13

4.2 Manual mode, Reduced ................................ 14

4.3 OFF mode ..................................................... 14

4.4 Automatic mode ............................................. 14

4.5 Program Mode .............................................. 14

4.6 Holiday mode ......................................... 19

4.7 Timer mode ................................................... 21

5 Special function .............................................. 21

5.1 Keyboards lock Function ............................... 21

6 Parameter’s menu .......................................... 22

7 Technical characteristics ................................ 25

6

Presentation

1

UFH - RF Digital programmable thermostat

Wireless (RF 868MHz) programmable thermostat specially

designed to control your Under Floor Heating managed by

actuator.

- Wall mounting with table support.

- Possibility to regulate on:

o Air sensor only

o Floor sensor only

o Air & Floor combined with different possibilities

- Amber Backlight

- “Easy program creation” function.

- Weekly programmable (By 30min step)

- Temporary override function.

- Timer or reception function.

- 2 AA batteries for 2 years of operating life time.

- Parameter menu, (User and Installer)

- Optional external sensor 10K at 25°C

7

1.1 Keyboard

( ) Back key to return to the previous menu.

(►+) Navigation key “right” in menu selection or plus

key for value edition.

(◄-) Navigation key “left” in menu selection or minus

key for value edition.

(OK) Validation key.

Backlight function:

Short press on this key (OK) permit to light up the

backlight for 10 seconds.

(i) Main menu key.

8

1.2 Display

1. Operating mode menu (active mode is framed).

2. Key lock indicator

3. Installation Parameter menu.

4. Current day of the week (1 = Monday)

5. Current time or parameter title if “ ” is

displayed.

6. Pictogram for program creation.

program state in normal operating mode.

7. Room or Floor Temperature indicator.

8. “Low Batteries” indicator.

9. RF transmission logo.

10. Heating indicator.

11. Room or floor temperature following the

indicator “7”.

Parameter value if “ ” is displayed.

12. Program of the current day

(the current time bar blinks)

1

2

3

4

5

6

7

11

10

9

8

12

9

First Installation

2

This section will guide you to set up your thermostat for the

first time.

2.1 Batteries installation

- Open the backside cover and insert the 2 AA Alkaline

supplied batteries (or remove the small protection sticker if

the batteries are already installed in the compartment)

- Close the cover.

- Now you are invited to adjust and configure the

necessaries parameters.

2.2 Time and Date adjustment

Each time a value blinks, you can adjust it with the (◄-)

and (►+) keys, once the value is chosen, validate it with

the (OK) key. The clock will jump automatically to the next

value.

you can always come back to the previous value by

pressing the escape key ( ).

List order of the time and date adjustments:

Time and day:

Adjustment of the hours,

Adjustment of the minutes

Adjustment of the day (1 = Monday)

Date:

Adjustment of the day number (0 to 31).

Adjustment of the month number (01 to 12).

Adjustment of the year (Century).

Adjustment of the year

Then the message “Save” appear, press (OK) to valid your

adjustments.

You can always reach the time and date adjustments, by

pressing and maintaining the (OK) key during 2 seconds in

normal operating modes.

10

RF installation

3

3.1 RF Installation with one zone wall receiver

a) First of all you must put the receiver in “RF init” mode.

For this, press the Receiver push button during 5sec,

the Green RF LED should lit up (fixed) indicating that

the Receiver is now in radio configuration mode

waiting for a clock configuration address. (In all the

cases check the receiver leaflet for more explanation)

b) To link others one zone receiver, repeat the step a.

c) Setup menu of the thermostat see 3.4

3.2 RF Installation with one zone flush receiver

a) First of all you must put the receiver in “RF init” mode.

For this, press the Receiver push button in the middle

of the receiver during 5sec, the Green RF LED should

lit up (fixed) indicating that the Receiver is now in radio

configuration mode waiting for a clock configuration

address. (In all the cases check the receiver leaflet for

more explanation)

b) To link others one zone receiver, repeat the step a.

c) Setup menu of the thermostat see 3.4

5 sec.

11

3.3 RF Installation with 6 zones Master

a) To put you master in „RF init“ mode, press 10 sec on

the (OK) button. The first led blinks green. The LED

light up green for the zones already linked. Choose the

zone with the (◄) or (►) buttons. The selected zone

is indicated by the corresponding green blinking LED.

b) Press (OK), the zone can be linked with the desired

thermostat. You can select several zones. The LED (s)

of the selected channel (s) bright (s) red, indicating

that they are waiting for the signal from the thermostat.

The LED of the zones well linked bright green instead

of rot.

c) If you want to link other thermostats, repeat the step a

and b. To exit the „RF init“ mode, press 10 sec. on the

(OK) button.

d) Setup menu of the thermostat see 3.4

e)

3.4 1 zone RF clock installation

a) You must enter in the installer menu by pressing the

(◄-) and (►+) keys during 5s, then the following

screen must be displayed.

To exit the RF installation mode, press on the ( ) button

or press on the (OK) until “End” is displayed. Then, press

(OK).

(OK) 10 sec.

12

The 1 zone RF clock is now installed. To test this, increase

the setpoint temperature in "Auto" mode at 30 ° C. The

corresponding zone must switch during 5 sec. When the

temperature decreases, the zone switch one more time.

For a quick installation, put the clock near the receiver. A

distance of 50cm minimum must be respected between the

clock and the receiver.

3.5 Starting

The clock is now ready to works.

The default working mode will be automatic with a

standard built-in program “P1” for all the zones.

Monday to Friday

20°C

18°C

07:00 09:00 17:00 23:00

Saturday & Sunday

20°C

18°C

08:00 23:00

Note:

You can customise your program as you want, See the

next part “Working mode definition” chapter “Zone

Program” for more explanation.

13

At any time, when the backlight is extinct, press the (OK)

key to lit-up the backlight,

Working mode definition

4

How to change the working mode?

- Press on the menu key (i) to show the working mode line.

- You can now press the keys (◄-) and (►+) to

move the frame cursor on the desired working mode and

press (OK) to valid you choice.

4.1 Manual mode Comfort

Press once on the (OK) to turn on the backlight only and a

second time to edit the setting temperature. Then press on

(◄-) or (►+) to start the increment or decrement of the

setting temperature.

The ambient room temperature reappears after a few

seconds.

The comfort temperature will be followed all the time.

(Default setting 20°C)

Curent

stage of the

program

Current

temperature

Daily

Program

Current

Time

14

4.2 Manual mode, Reduced

Press once on the (OK) to turn on the backlight only and a

second time to edit the setting temperature. Then press on

(◄-) or (►+) to start the increment or decrement of the

setting temperature.

The ambient room temperature reappears after a few

seconds.

The Reduced temperature will be followed all the time.

(Default setting 18°C)

4.3 OFF mode

Use this mode if you need to switch off your installation.

Be Careful:

- In this mode your installation can freeze.

- At any time, when display is off, press on the (Ok) key to

display a few seconds the current temperature and time.

- To restart your installation, use the navigation keys (◄-)

and (►+).

4.4 Automatic mode

In this mode your thermostat will follow the program

chosen in the “P” menu (Built-in or customized) according

to the time.

You can easily override, until next program step, the

current setting temperature. To make this, press once on

the (OK) to turn on the backlight only and a second time to

edit the setting temperature “blinking value”. You can now

adjust the setting with (◄-) or (►+).

The small hand logo will be displayed when override

function is active.

The override function will be stopped after the next step of

the program.

4.5 Program Mode

15

When you enter in the Program mode, the first operation is

to chose the program number

with (◄-) or (►+) keys.

You can choose between a built-in program P1 to P9 or a

user program U1 to U4.

If you chose a Built-in program P1 to P9,

You can only see and chose the program.

P1: Morning, Evening & Weekend

P2: Morning, Midday, Evening & Weekend

P3: Day & Weekend

P4: Evening & Weekend

P5: Morning, Evening (Bathroom)

P6: Morning, afternoon & Weekend

P7: 7H – 19H (Office)

P8: 8H – 19H & Saturday (Shop)

P9: Weekend (Secondary house)

(See the Annexe parts to view a complete description of

the Built-in program)

- Use the menu key (i) to change the program day

displayed.

- Press the (OK) key to confirm your choice and come back

to the main screen (in AUTO mode)

If you chose a user program U1 to U4,

As above you can choose the program, see it,

but you can also customise it.

Default setting:

U1, U2, U3, U4 = Comfort all week

Symbols and explanation for program creation:

Current

day

Program

of the day

Program

followed by

the displayed

zone

16

First step of the day ( Comfort temp.)

The wakeup hour need to be adjusted.

Middle step of the day ( Reduced temp.)

The leaving hour need to be adjusted

Middle step of the day ( Comfort temp.)

The comeback hour will need to be adjusted

Last step of the day ( Reduced temp.)

The sleeping hour need to be adjusted

- The program step is 30 minutes

- Each time a value or icon blinks you are invited to make a

choice with (◄-) or (►+) keys,

once the choice is made press the (OK) key to jump to the

following step.

- The program creation will always start with the day 1

(Monday).

Once you have pressed the (OK) key, the following display

will appear:

Now you are invited to adjust the hour of the first step of

the program with (◄-) or (►+),

17

Press (OK) to validate and go to the following step.

Now you are invited to choose the type of the next step of

the program (blinking icons),

2 choices will be possible:

- 1

st

choice is to choose the sleep icon. (End of the day)

- 2

nd

choice is to choose the leaving icon, to add one step

to the program during the day.

When the choice is made, press (OK) to validate.

Then you can adjust the step hour with (◄-) or (►+),

When step hour is set press (OK) to jump to the next step.

You will be directly invited to adjust with (◄-) or (►+) the

hour of the comeback step.

18

Press (OK) to validate and go to the following step.

You are again invited to choose the type of the next step of

the program (blinking icons),

2 choices will be possible:

- 1

st

choice is to choose the sleep icons. (End of the day)

- 2

nd

choice is to choose the leaving icons, to add another

step to the program during the day.

When the choice is made, press (OK) to valid and you can

adjust the hour of this step with (◄-) or (►+),

Press (OK) to validate and finish the edition of the first day.

Now you can choose to copy the program day just created

to subsequent days.

19

Change the choice “Yes” or “no” with (◄-) or (►+) and

validate your choice with (OK).

- If you select “no”, you will be invited to create a program

for Tuesday (repeat the previous method to build it.)

- If you select “Yes”, you will have the possibility to copy

the program to the following day (on Tuesday on

Wednesday... up to the last day of the week

(7 Sunday).

When you press (OK) on the last day (7 Sunday) you will

be invited to “SAVE” your program.

Then the message “Save” and blinking green LED

appears:

Press (OK) key to save your program and return to AUTO

operating mode following your user program.

- At any time you can exit the program creation mode by

pressing several times on the escape key ( ) to go back

up the made stages.

4.6 Holiday mode

Press (i) and (◄-) or (►+) to reach the Holiday mode.

20

The Holiday mode allows you to set the anti-freeze mode

for a selected number of days.

- You can adjust, the duration in day “d” with (◄-) or (►+),

press (OK) to start. (Adjustable 1 to 44 days)

The logo will blink and the number of days left is

displayed until the end of the period,

If you want to stop the Holiday function before the end, set

the duration period to “no” with (◄-) key or press on the

escape key ( ).

La page charge ...

RADSON 51044 Manuel utilisateur

RADSON 51044 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents