DeWalt D55167 Manuel utilisateur

D55167

Oil-Free Portable Air Compressor

Compresseur d’air portatif sans huile

Compresor de aire sin aceite portátil

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

2

English

A. On/Auto/Off Switch

B. Air Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Regulator

E. Quick Connect

Pump/Motor Speciﬁ cations

Voltage: Single Phase 120V

Minimum branch circuit requirement: 15 A

Fuse Type: Time delay

Speciﬁ cations

MODEL

D55167

WEIGHT

85 lbs. (39.92 kg)

HEIGHT

27.5"

(1060.5mm)

WIDTH

18.0" (482.6 mm)

LENGTH

21.25 (539.8 mm)

AIR TANK CAPACITY (GALLONS)

15 Gallon (56.8 liters)

APPROX CUT-IN PRESSURE

160 PSI

APPROX. CUT-OUT PRESSURE

200 PSI

SCFM @ 90 PSI (620.5 kPa)

*4.8

NOISE LEVEL

+79 dBA

*Tested per ISO 1217:1996

+Tested per ISO 3744:1994

D55167 Air Compressor

F. Check Valve

G. Safety Valve

H. Air Tank Drain Valve

(not shown)

I. Pressure Switch

J. Air Intake Filter

Declared Noise Emission Values per

ISO 3744

Noise Emission Values

Sound Pressure Level: LpA = 79.0 dBA re 20μPA

Uncertainty in the Sound Pressure Level: KpA = 3.0 dBA re 20μPA

Sound Power Level: LwA = 93.0 dBA re 1 pw

Uncertainty in the Sound Power Level: KwA = 3.0 dBA re 1 pw

The sum of the emission value and the uncertainty is the limit

below which there is a 95% confidence the value of a single tool

will lie below when the tool is new.

FIG. 1

A

E

C

B

D

I

G

F

J

3

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

E

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

E

WALT (1-800-433-9258)

Important Safety Instructions

WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

WARNING: Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals known

(to the State of California) to cause cancer, birth defects or other

reproductive harm. Some example of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement and other masonry

products

• arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, al ways wear OSHA/MSHA/NIOSH approved, properly

fit ting face mask or res pi ra tor when us ing such tools.

When using air tools, basic safety precautions should always be

followed to reduce the risk of of personal injury.

WARNING: This product contains chemicals, including lead,

known to the State of California to cause cancer, and birth

defects or other reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTION

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• It is normal for electrical con-

tacts within the motor and

pressure switch to spark.

• Always operate the compres-

sor in a well ventilated area

free of combustible materials,

gasoline, or solvent vapors.

4

English

• If electrical sparks from

compressor come into con-

tact with flammable vapors,

they may ignite, causing fire

or explosion.

• If spraying flammable materi-

als, locate compressor at

least 20 feet (6.1 m) away

from spray area. An addi-

tional length of hose may be

required.

• Store flammable materials in

a secure location away from

compressor.

• Restricting any of the com-

pressor ventilation openings

will cause serious overheat-

ing and could cause fire.

• Never place objects against or

on top of compressor.

• Operate compressor in

an open area at least 12"

(30 cm) away from any wall or

obstruction that would restrict

the flow of fresh air to the

ventilation openings.

• Operate compressor in a

clean, dry well ventilated area.

Do not operate unit indoors or

in any confined area.

• Unattended operation of

this product could result in

personal injury or property

damage. To reduce the risk

of fire, do not allow the

compressor to operate unat-

tended.

• Always remain in attendance

with the product when it is

operating.

• Always turn off and unplug

unit when not in use.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air directly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminant's can cause

serious injury or death.

• Air obtained directly from the

compressor should never be

used to supply air for human

consumption. In order to use air

produced by this compressor

for breathing, suitable filters

and in-line safety equipment

must be properly installed. In-

line filters and safety equipment

used in conjunction with the

compressor must be capable

of treating air to all applicable

local and federal codes prior to

human consumption.

• Sprayed materials such as

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or safety

data sheets for the materials

you are spraying. Always use

certified safety equipment:

OSHA/MSHA/NIOSH

respiratory protection designed

for use with your specific

application.

5

English

WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed and may

be UM coded (for units with air tanks greater than 6 inch diameter)

according to ASME Section VIII, Div. 1 rules. All pressure vessels

should be inspected once every two years. To find your state pressure

vessels inspector, look under the Division of Labor and Industries in

the government section of a phone book or call 1-800-4-D

EWALT for

assistance.

The following conditions could lead to a weakening of the air tank, and

result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drain air tank daily or after

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modifications or attempted

repairs to the air tank.

• Never drill into, weld, or make

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorized modifications to

the safety valve or any other

components which control air

tank pressure.

• The air tank is designed

to withstand specific

operating pressures. Never

make adjustments or parts

substitutions to alter the factory

set operating pressures.

Attachments & accessories:

• Exceeding the pressure

rating of air tools, spray guns,

air operated accessories,

tires, and other inflatables

can cause them to explode or

fly apart, and could result in

serious injury.

• Follow the equipment

manufacturers

recommendation and never

exceed the maximum allowable

pressure rating of attachments.

Never use compressor to

inflate small low pressure

objects such as children’s toys,

footballs, basketballs, etc.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your air compressor is

powered by electricity.

Like any other electrically

powered device, If it is not

used properly it may cause

electric shock.

• Never operate the compressor

outdoors when it is raining or

in wet conditions.

• Never operate compressor

with protective covers

removed or damaged.

• Repairs attempted by

unqualified personnel can

result in serious injury or

death by electrocution.

• Any electrical wiring or

repairs required on this

product should be performed

by a D

EWALT factory

service center or a D

EWALT

authorized service center in

accordance with national and

local electrical codes.

6

English

• Electrical Grounding:

Failure to provide adequate

grounding to this product

could result in serious injury

or death from electrocution.

See Grounding

Instructions under

Installation.

• Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage and

adequate fuse protection.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air stream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particles, and small objects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people or

animals.

• Always turn the compressor off

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal such

as the compressor head,

engine head, engine exhaust

or outlet tubes, can result in

serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation.

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Moving parts such as the

pulley, flywheel, and belt can

cause serious injury if they

come into contact with you or

your clothing.

• Never operate the compressor

with guards or covers which

are damaged or removed.

• Keep your hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long

hair can be caught in moving

parts.

• Air vents may cover moving

parts and should be avoided as

well.

7

English

• Attempting to operate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in

serious injury.

• Any repairs required on this

product should be performed

by a D

EWALT factory service

center or a D

EWALT authorized

service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your air

compressor could lead to se ri-

ous in ju ry or death to you or

others.

• Review and understand all

instructions and warnings in

this manual.

• Be come fa mil iar with the

op eration and con trols of the

air compressor.

• Keep operating area clear of all

persons, pets, and obstacles.

• Keep chil dren away from the air

compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea-

tures of this prod uct.

• Do not use compressor to

support workpiece.

• Do not use compressor for tool

storage.

•

Do not store or operate with

tank in vertical position.

• Equip area of operation with a

fire extinguisher.

• Do not op er ate machine with

missing, broken, or un au tho-

rized parts.

WARNING: RISK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT IT

• A portable compressor

can fall from a table,

workbench, or roof causing

damage to the compressor

and could result in serious

injury or death to the

operator.

• Always operate compressor

in a stable secure position to

prevent accidental movement

of the unit. Never operate

compressor on a roof or

other elevated position. Use

additional air hose to reach

high locations.

8

English

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute

to hearing loss.

• Always wear certified safety

equipment: ANSI S12.6

(S3.19) hearing protection.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FEATURES

ON/AUTO/OFF SWITCH

Place this switch (A) in the ON/AUTO

F

A

I

G

position to provide automatic power

to the pressure switch and OFF to

remove power at the end of each

use.

PRESSURE SWITCH

The pressure switch (I) automatically

starts the motor when the air tank

pressure drops below the factory set cut-in pressure. It stops the

motor when the air tank pressure reaches the factory set cut-out

pressure.

SAFETY VALVE

If the pressure switch does not shut off the air compressor at its

cut-out pressure setting, the safety valve (G) will protect against

high pressure by popping out at its factory set pressure (slightly

higher than the pressure switch cut-out setting).

CHECK VALVE

When the air compressor is operating, the check valve (F) is

open, allowing compressed air to enter the air tank. When the

air compressor reaches cut-out pressure, the check valve closes,

allowing air pressure to remain inside the air tank.

TANK PRESSURE GAUGE

The tank pressure gauge (B)

G

E

C

D

B

indicates the reserve air pressure

in the tank.

OUTLET PRESSURE GAUGE

The outlet pressure gauge (C)

indicates the air pressure available

at the outlet side of the regulator.

This pressure is controlled by the

regulator and is always less than or equal to the tank pressure.

REGULATOR

The regulator (D) controls the air pressure shown on the outlet

pressure gauge. Pull the knob out and turn clockwise to increase

pressure and counterclockwise to decrease pressure. When the

desired pressure is reached push knob in to lock in place.

UNIVERSAL QUICK CONNECT BODY

The universal quick connect body (E) accepts the three most

popular styles of quick connect plugs: Industrial, automotive, and

ARO. One hand push-to-connect operation makes connections

simple and easy.

DRAIN VALVE

The drain valve (H) is located at the base of the air

H

tank and is used to drain condensation at the end

of each use.

See Draining Air Tank under

Maintenance.

9

English

COOLING SYSTEM

This compressor contains an advanced design cooling system.

It is normal for this fan to blow air through the vent holes in large

amounts. The cooling system is working when air is expelled.

AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure

above that required at the air outlet.

AIR INTAKE FILTER

The filter (J) is designed to clean air entering the pump. To ensure

the pump continually receives a clean, cool, and dry air supply the

filter must always be clean and the filter intake must be free from

obstructions.

PRESSURE RELEASE VALVE

The pressure release valve located on the side of the pressure switch,

is designed to automatically release compressed air from the compres-

sor head and the outlet tube when the air compressor reaches cut-out

pressure or is shut off. The pressure release valve allows the motor to

restart freely. When the motor stops running, air will be heard escaping

from this valve for a few seconds. No air should be heard leaking when

the motor is running or after the unit reaches cut-out pressure.

MOTOR OVERLOAD PROTECTOR

The motor has a thermal overload protector. If the motor overheats

for any reason, the overload protector will shut off the motor. The

motor must be allowed to cool down before restarting. To restart:

1. Set the On/Auto/Off lever to OFF and unplug unit.

2. Allow the motor to cool.

3.

Plug the power cord into the correct branch circuit receptacle.

4. Set the On/Auto/Off lever to ON/AUTO position.

INSTALLATION

Assembly

INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI.

2. Grasp the hose at the quick connect plug and push the plug

into the quick connect body (E). Coupler will snap into place.

3. Grasp the hose and pull to ensure coupler is seated.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI.

2. Pull coupler on quick connect body back to release Quick

Connect plug on hose.

Grounding Instructions

WARNING: Risk of Electrical Shock. In the event of a short

circuit, grounding reduces the risk of shock by providing an escape

wire for the electric current. This air compressor must be properly

grounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug.

1. The cord set and plug (M) with this unit

L

M

K

contains a grounding pin (L). This plug

MUST be used with a grounded

outlet (K).

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

10

English

2. Ensure the outlet being used has the same configuration as the

grounded plug. DO NOT USE AN ADAPTER.

3. Inspect the plug and cord before each use. Do not use if there

are signs of damage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualified electrician.

DANGER: Risk of Electrical Shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICAL SHOCK.

• Do not modify the plug provided. If it does not fit the available

outlet, a correct outlet should be installed by a qualified

electrician.

• Repairs to the cord set or plug MUST be made by a qualified

electrician.

Extension Cords

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding plug, and

a 3-slot receptacle that will accept the plug on the product

• in good condition

• no longer than 50 feet

• 12 gauge (AWG) or larger. (Wire size increases as gauge

number decreases. 10 AWG and 8 AWG may also be used. DO

NOT USE 14 OR 16 AWG.)

CAUTION: The use of an undersized extension cord will cause

voltage to drop resulting in power loss to the motor and overheating.

Instead of using an extension cord, increase the working reach of

the air hose by attaching another length of hose to its end. Attach

additional lengths of hose as needed.

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit Requirements

under Pump/Motor Specifications.

CAUTION: Certain air compressors can be operated on a

15 amp circuit if the following conditions are met.

• Voltage supply to circuit must comply with the National

Electrical Code.

• Circuit is not used to supply any other electrical needs.

• Extension cords comply with specifications.

• Circuit is equipped with a 15 amp circuit breaker or 15 amp

time delay fuse. NOTE: If compressor is connected to a circuit

protected by fuses, use only time delay fuses. Time delay

fuses should be marked “D” in Canada and “T” in the US.

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a 20 amp circuit. It is not necessary

to change the cord set.

Compatibility

NOTE: Always use an air line filter to remove moisture when

spraying paint.

Location

Place the air compressor in a clean, dry and well ventilated area

at least 12" (30 mm) away from the wall or other obstructions that

will interfere with the flow of air. Keep the compressor away from

areas that have dirt and/or volatile fumes in the atmosphere. These

impurities may clog the intake filter and valves, causing inefficient

operation.

WARNING: The air compressor pump and shroud are designed

to allow for proper cooling. The ventilation openings on the com-

pressor are necessary to maintain proper operating temperature.

Do not place rags or other containers on or near these openings.

Place the air compressor on a flat surface resting on the rubber

feet and wheels.

11

English

ELECTRICAL

Refer to all safety instructions before using unit. Observe extension

cord safety instructions if necessary. Always move the On/Auto/Off

switch (A) to the OFF position before removing the plug from the

outlet.

TRANSPORTING

When transporting the compressor in a vehicle, trailer, etc., make

sure the tank is drained and the unit is secured with straps to prevent

tipping. Use care when driving to prevent tipping the unit over in the

vehicle. Damage can occur to the compressor or surrounding items

if the compressor is tipped.

LIFTING

Always use two people when lifting and lift

N

from the recommended lift points

(N). DO NOT

lift

by wheels or shroud.

MOVING

CAUTION: The wheels and handle do

not provide adequate clearance, stability, or

support for pulling the unit up and down stairs or steps. The unit must

be lifted or pushed up a ramp.

1. Grasp handle of compressor and tilt compressor back to rest on

wheels.

WARNING: Risk of Unsafe Operation. Ensure proper footing and

use caution when rolling compressor so that unit does not tip or

cause loss of balance.

2. When location is reached slowly lower compressor to ground.

Always store compressor

in a horizontal position resting on

the rubber bumpers and wheels.

PREPARATION FOR USE

Pre-Start Checklist (Fig. 1)

1.

Ensure the On/Auto/Off switch (A) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

4. Ensure the drain valve (H) is closed.

5. Ensure safety valve (G) is functioning properly, see Checking

Safety Valve under Maintenance.

6. Pull the regulator knob (D) out and turn counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 PSI. Push knob

in to lock in place.

7. Attach hose and accessories. NOTE: Always use a minimum

3/8" (9.5 mm) or greater air hose rated at 300 PSI.

WARNING: Risk of unsafe operation. Firmly grasp air hose in hand

when installing or disconnecting to prevent hose whip.

WARNING:

Risk of unsafe operation. Do not use damaged or worn

accessories.

WARNING: Risk of Bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure rating.

Initial Set-up

(Fig. 1)

WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

12

English

BREAK-IN PROCEDURE

WARNING: Risk of property damage. Serious damage may result

if the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into

service for the first time and when the check valve or a compressor

pump/motor has been replaced.

1. Ensure the On/Auto/Off switch (A) is in the OFF position.

NOTE: If hose is not connected to Quick Connect body, pull coupler

back until it clicks to prevent air from escaping through the quick

connect.

2.

Plug the power cord into the correct branch circuit receptacle.

See Voltage and Circuit Protection under Installation.

3. Open the drain valve (turn lever counter-clockwise) fully to

permit air to escape and prevent air pressure build up in the air

tank during the break-in period.

4. Move the On/Auto/Off switch to the ON position. The compressor

will start.

5. Run the compressor for 15 minutes.

6. After 15 minutes, close the drain valve by turning lever

clockwise. The tank will fill to cut-out pressure and the motor

will stop.

7. Compressed air will be available until it is used or bled off.

OPERATING PROCEDURES

Start-up (Fig. 1)

1. Follow Pre-Start Checklist under Preparation for Use.

2. Move the On/Auto/Off switch to the ON position and allow tank

pressure to build. Motor will stop when tank pressure reaches

cut-out pressure.

CAUTION: Risk of unsafe operation. Compressed air from the

unit may contain wa ter condensation and oil mist. Do not spray un fil-

tered air at an item that could be damaged by moisture. Some air

op er ated tools or de vic es may require filtered air. Read the in struc-

tions for the air tool or device.

3. Adjust regulator (

D) to desired setting. See Regulator under

Features.

Shut-down (Fig. 1)

1. Move On/Auto/Off switch (A) to the OFF position. NOTE: If

finished using compressor, follow Steps 2 - 6.

NOTE: When the unit has been turned off, it is normal to hear a

short hiss of air being released.

2. Pull the regulator knob (

D) out and turn counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 PSI. Push knob

in to lock in place.

3. Remove hose and accessory.

WARNING: Risk of unsafe operation. Firmly grasp air hose in hand

when installing or disconnecting to prevent hose whip.

4. Drain the air tank,

see Draining Air Tank under Maintenance

.

Ensure air tank pressure gauge reads 0 PSI.

WARNING: Risk of bursting. Drain air tank daily. Water will

condense in air tank. If not drained, water will corrode and weaken

the air tank causing a risk of air tank rupture.

5. Allow the compressor to cool down.

6. Wipe air compressor clean and store in a safe, non-freezing area.

MAINTENANCE

The following procedures must be followed when maintenance or

service is performed on the air compressor.

13

English

1. Ensure On/Auto/Off switch is in the OFF position.

2. Remove air compressor plug from outlet.

3. Drain air tank.

4. Allow air compressor to cool down before starting service.

NOTE: All compressed air systems contain maintenance parts (e.g.,

oil, filters, separators) that are periodically replaced. These used parts

may contain substances that are regulated and must be disposed of in

accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should

be performed by a D

E

WALT factory service center or a D

E

WALT

authorized service center.

Maintenance Chart

Before

each

use

Daily or

after each

use

Every

100

hours

Ye a r l y

Check Safety Valve X

Drain Tank X

Air Filter X

1

Air compressor

pump intake and

exhaust valves

X

1- more frequent in dusty or humid conditions

Checking Safety Valve

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

an explosion.

WARNING: Risk from flying objects. Always wear certified safety

equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side

shields when using the compressor.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. NOTE: Ring may

be difficult to pull when air tank pressure is at 0 PSI. If the valve is

stuck or does not operate smoothly, it must be replaced with the

same type of valve.

Draining Air Tank (Fig. 1)

WARNING: Risk of unsafe operation. Air tanks contain high pres-

sure air. Keep face and other body parts away from outlet of drain.

Use eye protection ANSI Z87.1 [ANSI Z87.1 (CAN/CSA Z94.3)]

when draining as debris can be kicked up into face.

WARNING: Risk from noise. Use [ANSI S12.6 (S3.19)] ear

protection as air flow noise is loud when draining.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g., tanks, filter, aftercoolers,

dryers). This condensate contains lubricating oil and/or substances

which may be regulated and must be disposed of in accordance with

local, state, and federal laws and regulations.

1. Ensure On/Auto/Off switch (A) is in the OFF position.

2. Move compressor into an inclined position so drain valve (H) is

at the lowest point (this will assist in removing moisture, dirt, etc.

from air tanks)

WARNING: Risk of bursting. Drain air tank daily. Water will con-

dense in air tank. If not drained, water will corrode and weaken the

air tank causing a risk of air tank rupture.

CAUTION:

Risk of Property Damage. Drain water from air tank may

contain oil and rust which can cause stains.

3. Place a suitable container under the drain valve to catch

discharge.

14

English

4. Grasp black lever on drain valve.

5. Slowly rotate lever to gradually bleed air from air tank.

6. When air tank pressure gauge reads 10 PSI, rotate valve to the

fully open position.

7. Close drain valve when finished.

Checking Air Filter Element (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Outlet tube, pump head,

and surrounding parts are very hot, do not touch. Allow compressor

to cool prior to servicing.

1. Ensure On/Auto/Off switch (A) is in the

J

OFF Position.

2. Allow unit to cool.

3. Remove filter cover (J) from base.

4. Remove element from filter base.

5. Place new element back in filter base.

Purchase replacement parts from your

local dealer or authorized service center. Always use identical

replacement parts.

6. Snap filter cover to filter base.

CAUTION: Risk of unsafe operation. Do not operate without air

inlet filter

ACCESSORIES

Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center.

If you need assistance in locating any accessory for your tool,

please contact D

E

WALT Industrial Tool Co., 701 East Joppa Road,

Baltimore, MD 21286, call 1-800-4-D

E

WALT (1-800-433-9258) or visit

our website www.dewalt.com.

WARNING: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compressor.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number ____________ Serial Number _________________

Date and Place of Purchase ______________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D

E

WALT factory service

center, a D

E

WALT authorized service center or other qualified

service personnel. Always use identical replacement parts.

Full One Year Warranty

DEWALT heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

E

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

15

English

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

E

WALT for a free

replacement.

WARNING

DRAIN TANK DAILY

OR AFTER EVERY 4 HOURS OF USE. CONDENSATION BUILD-UP MAY CAUSE

CORROSION INSIDE TANK RESULTING IN TANK FAILURE. SEE MANUAL FOR INSPECTION PROCEDURES.

TO DRAIN TANK OPEN VALVE SLOWLY AND TILT COMPRESSOR TO EMPTY ACCUMULATED WATER.

ADVERTENCIA

DRENE EL TANQUE A DIARIO O DESPUÉS DE CADA 4 HORAS DE USO. LA ACUMULACIÓN DE

CONDENSACIÓN PUEDE OCASIONAR CORROSIÓN DENTRO DEL TANQUE Y PROVOCAR FALLA DEL

TANQUE. CONSULTE EL MANUAL PARA CONOCER LOS PROCEDIMIENTOS DE INSPECCIÓN. PARA DRENAR EL TANQUE, ABRA LA

VÁLVULA LENTAMENTE E INCLINE EL COMPRESOR PARAELIMINAR EL AGUA ACUMULADA.

AVERTISSEMENT

RÉSERVOIR DE VIDANGE QUOTIDIEN OU APRÈS TOUTES LES 4 HEURES D'UTILISATION.

L'HABILLAGE DE CONDENSATION PEUT CAUSER LA CORROSION À L'INTÉRIEUR DU RÉSERVOIR AYANT

POUR RÉSULTAT L'ÉCHEC DE RÉSERVOIR. VOIR LE MANUEL POUR DES PROCÉDURES D'INSPECTION. À LA VALVE

OUVERTE DE RÉSERVOIR DE VIDANGE LENTEMENT ET AU COMPRESSEUR D'INCLINAISON À L'EAU ACCUMULÉE VIDE.

WARNING

HOT SURFACES

ADVERTENCIA

SUPERFICIES CALIENTES

AVERTISSEMENT

SURFACES CHAUDES

DO NOT ADJUST FACTORY SETTINGS.

TO REDUCE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER.

Pressure controls set at factory for

maximum safe operation.

NO HAGA CAMBIOS EN LOS AJUSTES

DE FÁBRICA. NO RETIRE LA TAPA PARA

REDUCIR EL RIESGO DE CHOQUE ELÉCTRICO.

Los controles de presión se ajustan en la

fábrica para máxima seguridad en la operación.

ADVERTENCIA

WARNING

AVERTISSEMENT

GLOSSARY

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air

delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

kPa (kilopascal): Metric pressure measurement. 1 kilopascal

equal 1000 pascals.

Code Certification: Products that bear one or more of the

following marks: UL, CUL, ETL, CETL, have been evaluated by

OSHA certified independent safety laboratories and meet the

applicable Underwriters Laboratories Standards for Safety.

Cut-In Pressure: While the motor is off, air tank pressure drops

when accessory is used. When the tank pressure drops to a certain

low level the motor will restart automatically. The low pressure at

which the motor automatically restarts is called cut-in pressure.

Cut-Out Pressure: When an air compressor is turned on and

begins to run, air pressure in the air tank begins to build. It builds

to a certain high pressure before the motor automatically shuts

off, protecting your air tank from pressure higher than its capacity.

The high pressure at which the motor shuts off is called cut-out

pressure.

Branch Circuit: The circuit carrying electricity from electrical panel

to outlet.

Duty Cycle: This air compressor pump is capable of running

continuously. However, to prolong the life of your air compressor,

it is recommended that a 50%-75% average duty cycle be

maintained; that is, the air compressor pump should not run more

than 30-45 minutes in any given hour.

16

English

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance

personnel can perform some corrective actions, and others may require the assistance of a qualified D

EWALT technician or your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off ......................................................................1,2

Air leaks ....................................................................................................................................3

Air leaks in air tank or at air tank welds ....................................................................................4

Air leaks between head and valve plate ....................................................................................5

Air leaks from safety valve .........................................................................................................6

Knocking Noise ..........................................................................................................................6

Pressure reading on the regulated pressure gauge drops when an accessory is used ...........7

Compressor is not supplying enough air to operate accessories..............................................8,9,10,11,12,23

Regulator knob has continuous air leak ....................................................................................13

Regulator will not shut off air outlet ...........................................................................................13

Motor will not run .......................................................................................................................6,14,15,16,17,18,19,20,21

Squealing Sound .......................................................................................................................22

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off motor when com-

pressor reaches cut-out pressure

Set the On/Auto/Off switch to OFF, if the unit does not shut off

contact a D

E

WALT factory service center or a D

E

WALT authorized

service center.

2 Pressure switch cut-out too high Contact a D

E

WALT factory service center or a D

E

WALT authorized

service center.

3 Tube fittings are not tight enough Tighten fittings where air can be heard escaping. Check fittings with

soapy water solution. Do Not Overtighten.

17

English

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

4 Defective air tank Air tank must be replaced. Do not repair the leak.

WARNING: Risk of bursting. Do not drill into, weld or other-

wise modify air tank or it will weaken. The air tank can rupture or

explode.

5 Leaking seals Contact a D

E

WALT factory service center or a D

E

WALT authorized

service center.

6 Defective safety valve Operate safety valve manually by pulling on ring. If valve still leaks,

it must be replaced.

7

Regulator is not adjusted correctly for accessory

being used

It is normal for some pressure drop to occur when an accessory is

used, adjust the regulator as instructed in Regulator under Features

if pressure drop is excessive.

NOTE: Adjust the regulated pressure under flow conditions while

accessory is being used.

8 Prolonged excessive use of air Decrease amount of air usage.

9 Compressor is not large enough for accessory Check the accessory air requirement. If it is higher than the CFM or

pressure supplied by your air compressor, a larger compressor is

needed to operate accessory.

10 Hole in air hose Replace air hose.

11 Check valve restricted Remove, clean or replace.

12 Air leaks Tighten fittings.

13 Regulator is damaged Replace.

14 Motor overload protection switch has tripped Refer to Motor Overload Protection under Features. If motor over-

load protection trips frequently, contact a D

E

WALT factory service

center or a D

E

WALT authorized service center.

18

English

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

15 Tank pressure exceeds pressure switch cut-in

pressure

Motor will start automatically when tank pressure drops below cut-in

pressure of pressure switch.

16 Extension cord is wrong length or gauge Check for proper gauge wire and cord length. Refer to the Extension

Cords paragraph in the Installation section.

17 Loose electrical connections Contact a D

E

WALT factory service center or a D

E

WALT authorized

service center.

18 Possible defective motor Contact a D

E

WALT factory service center or a D

E

WALT authorized

service center.

19 Paint spray on internal motor parts Contact a D

E

WALT factory service center or a D

E

WALT authorized

service center. Do not operate the compressor in the paint spray

area. See flammable vapor warning.

20 Pressure release valve on pressure switch has not

unloaded head pressure

Bleed the line by pushing the lever on the pressure switch to the

"OFF" position; if the valve does not open, replace switch.

21 Fuse blown, circuit breaker tripped 1. Check fuse box for blown fuse and replace as necessary. Reset

circuit breaker. Do not use a fuse or circuit breaker with higher

rating than that specified for our particular branch circuit.

2. Check for proper fuse. You should use a time delay fuse.

3. Check for low voltage conditions and/or proper extension cord.

4. Disconnect the other electrical appliances from circuit or operate

the compressor on its own branch circuit.

22

Worn Belt Contact a D

E

WALT factory service center or a D

E

WALT authorized

service center.

23 Restricted air intake filter Clean or replace air intake filter. Do not operate the air compressor

with the filter removed. Refer to the Air Filter paragraph in the

Maintenance section.

19

Français

FIG. 1

Compresseur d’air, modèle D55167

A. Interrupteur Marche/Arrêt

B. Manomètre du réservoir d’air

C. Manomètre régulé

D. Régulateur

E. Branchements rapides

F. Clapet

G. Soupape de sûreté

H. Soupape de purge du

réservoir d’air (non montré)

I. Rembobineur de cordon

d’alimentation

J. Filtre d’admission d’air

Fiche technique de la pompe/du moteur

Tension : monophasé, 120V

Exigence minimale du circuit de dérivation : 15 A

Type de fusible : temporisation

Fiche technique

MODÈLE

D55167

POIDS

39,92 kg (85 livres)

HAUTEUR

1060.5, mm(27,5 po)

LARGEUR

482,6 mm (18,0 po)

LONGUEUR

21,25 mm (539,8 po)

CAPACITÉ DU RÉSERVOIR D’AIR

(GALLONS)

15 (56,8 liters)

PRESSION D’ENCLENCHEMENT

APPROX.

160 PSI

ENV. PRESSION DE DÉCLENCHEMENT

200 PSI

PCMS (SCFM) @ 90 PSI

*4,8

NIVEAU SONORE

+79 dBA

*Testé conformément à la norme ISO 1217

+ Testé conformément à la norme ISO 3744

Valeurs de l’émission de bruits déclarées

en conformité avec l’ISO 3744

Valeur de l’émission de bruits

Niveau de pression acoustique :

LpA = 79,0 dBA re 20μPA

Incertitude du niveau de

pression acoustique calculé : KpA = 3,0 dBA re 20μPA

Niveau de puissance acoustique : LwA = 93,0 dBA re 1 pw

Incertitude du niveau de puissance

acoustique : KwA = 3,0 dBA re 1 pw

La somme de la valeur de l’émission et de l’incertitude établit la

limite sous laquelle la valeur pour un seul outil y sera inférieure et

ce, à 95 % de fiabilité statistique.

A

E

C

B

D

I

G

F

J

20

Français

Déﬁ nitions : lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de gravité pour

chaque symbole. Veuillez lire le mode d’emploi et porter une atten-

tion particulière à ces symboles.

DANGER : Indique une situation dangereuse imminente qui, si

elle n’est pas évitée, causera la mort ou des blessures graves.

AVERTISSEMENT :

Indique une situation potentiellement dan-

gereuse qui, si elle n’est pas évitée, pourrait se solder par un

décès ou des blessures graves.

MISE EN GARDE : Indique une situation potentiellement dan-

gereuse qui, si elle n’est pas évitée pourrait se solder par des

blessures mineures ou modérées.

MISE EN GARDE : Utilisé sans le symbole d’alerte à la sécurité,

indique une situation potentiellement dangereuse qui, si elle n'est

pas évitée pourrait se solder par des dommages à la propriété.

POUR TOUTES QUESTIONS OU COMMENTAIRES RELATIFS(VES)

À L’OUTIL OU À PROPOS DE TOUT AUTRE OUTIL D

EWALT,

COMPOSER SANS FRAIS LE : 1-800-4-D

EWALT (1-800-433-9258)

Directives de sécurité importantes

AVERTISSEMENT : Ne pas utiliser cet appareil avant d’avoir lu

et compris le mode d’emploi ainsi que l’intégralité des directives de

sécurité, d’utilisation et d’entretien.

AVERTISSEMENT : Nertaines poussières produites par les travaux

de ponçage, sciage, meulage, perçage et autres peuvent contenir des

produits chimiques pouvant (selon l’état de Californie) causer le cancer,

des anomalies congénitales ou d’autres problèmes liés aux fonctions

reproductrices. Voici quelques exemples de ces produits chimiques :

• le plomb contenu dans les peintures à base de plomb;

• la silice cristalline provenant de la brique, du ciment et d’autres

produits de maçonnerie;

• l’arsenic et chrome provenant de bois traité chimiquement.

Les risques reliés à l’exposition à ces poussières varient selon la

fréquence à laquelle l’utilisateur travaille avec ce type de matériaux.

Pour réduire votre exposition à ces produits chimiques : travailler dans

un endroit bien ventilé et porter un équipement de sécurité approuvé

par l’OSHA/MSHA/NIOSH comme un masque anti-poussières

spécialement adapté ou un respirateur lors de l’utilisation de ces outils.

Lors de l’utilisation d’outils pneumatiques, des précautions de base

en matière de sécurité doivent être suivies afin de réduire le risque de

blessure personnelle.

AVERTISSEMENT : Ce produit contient des produits chimiques,

notamment le plomb, reconnus par l’État de Californie comme

étant cancérigènes et pouvant entraîner des anomalies congé-

nitales et d’autres dangers relatifs à la reproduction. Se laver le

s

mains après toute manipulation.

CONSERVER CES DIRECTIVES

DANGER :

RISQUE D’EXPLOSION OU D’INCENDIE

Ce qui peut se produire Comment l’Éviter

• Il est normal que des

contacts électriques dans le

moteur et le manocontacteur

fassent une étincelle.

• Faites toujours fonctionner

le compresseur dans une

zone bien aérée sans matière

combustible, essence ou

vapeur de solvant.

La page charge ...

DeWalt D55167 Manuel utilisateur

DeWalt D55167 Manuel utilisateur

dans d''autres langues

Documents connexes