Sony CDX-R30M Manuel utilisateur

Marque: Sony

Modèle: CDX-R30M

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Operating Instructions

Mode d’emploi

2-671-367-11 (1)

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. CDX-R30M Serial No.

CDX-R30M

To cancel the demonstration (DEMO) display, see page 9.

Pour annuler l’affichage de démonstration (DEMO), reportez-vous à la page 10.

Compact Disc

Player

Welcome !

Thank you for purchasing this Sony Compact

Disc Player. You can enjoy your drive with the

following functions.

• CD playback:

You can play CD-DA (also containing CD

TEXT*), CD-R/CD-RW (MP3 files also

containing Multi Session (page 12)) and

ATRAC CD (ATRAC3 and ATRAC3plus

format (page 13)).

• Radio reception:

– You can store up to 6 stations per band (FM1,

FM2, FM3, AM1 and AM2).

– BTM (Best Tuning Memory) function: the

unit selects strong signal stations and stores

them.

– You can assign a name to each radio station,

store it in memory, and display station names

on the list.

• Optional unit operation

You can also control optional CD/MD

changers, in addition to playing with this unit.

* A CD TEXT disc is a CD-DA that includes

information such as disc, artist and track name.

Warning

Type of discs Label on the disc

CD-DA

MP3

ATRAC CD

For installation and connections, see the

supplied installation/connections manual.

The use of optical instruments with this produc

will increase e

e hazard.

CAUTION

Warning if your car’s ignition has no

ACC position

After turning the ignition off, be sure to press

and hold (OFF) on the unit until the display

disappears.

Otherwise, the display does not turn off and

this causes battery drain.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

–

Reorient or relocate the receiving antenna.

–

Increase the separation between the equipment

and receiver.

–

Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

–

Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

This label is located on the bottom of the

chassis.

Table of Contents

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . . . 4

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 4

Detaching the front panel . . . . . . . . . . . . . . . . . 4

Attaching the front panel . . . . . . . . . . . . . . . 4

Inserting the disc in the unit . . . . . . . . . . . . . . . 5

Ejecting the disc . . . . . . . . . . . . . . . . . . . . . . 5

Location of controls and basic

operations

Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Display items . . . . . . . . . . . . . . . . . . . . . . . . 7

Repeat and shuffle play . . . . . . . . . . . . . . . . 7

Radio

Storing and receiving stations . . . . . . . . . . . . . . 7

Storing automatically — BTM . . . . . . . . . . 7

Storing manually . . . . . . . . . . . . . . . . . . . . . 7

Receiving the stored stations . . . . . . . . . . . . 7

Tuning automatically . . . . . . . . . . . . . . . . . . 7

Receiving a station through a list

— list-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Other functions

Changing the sound settings . . . . . . . . . . . . . . . 8

Adjusting the sound characteristics

— BAL/FAD/SUB . . . . . . . . . . . . . . . . . . . 8

Adjusting the equalizer curve — EQ3 . . . . 8

Labeling a station/disc . . . . . . . . . . . . . . . . . . . 9

Adjusting setup items — SET . . . . . . . . . . . . . 9

Using optional equipment. . . . . . . . . . . . . . . . 10

CD/MD changer . . . . . . . . . . . . . . . . . . . . 10

Card remote commander RM-X114 . . . . . 10

Rotary commander RM-X4S . . . . . . . . . . 11

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Notes on discs . . . . . . . . . . . . . . . . . . . . . . 12

About MP3 files . . . . . . . . . . . . . . . . . . . . 12

About ATRAC CD . . . . . . . . . . . . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Removing the unit. . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 15

Error displays/Messages . . . . . . . . . . . . . . 16

The “SAT Radio Ready”

logo indicates that this

product will control a satellite

radio tuner module (sold

separately). Please see your nearest authorized

Sony dealer for details on the satellite radio

tuner module.

“SAT Radio,” “SAT Radio Ready,” the SAT

Radio and SAT Radio Ready logos and all

related marks are trademarks of Sirius Satellite

Radio Inc. and XM Satellite Radio Inc.

SonicStage and its logo are trademarks of Sony

Corporation.

ATRAC, ATRAC3, ATRAC3plus and their logos

are trademarks of Sony Corporation.

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Detach the front panel and press the RESET

button with a pointed object, such as a ball-point

pen.

Note

Pressing the RESET button will erase the clock setting

and some stored contents.

Setting the clock

The clock uses a 12-hour digital indication.

1 Press and hold (SEL).

The setup display appears.

2 Press (SEL) repeatedly until “CLOCK-

ADJ” appears.

3 Press (DSPL ) .

The hour indication flashes.

4 Press the volume +/– button to set the

hour and minute.

To move the digital indication, press (DSPL).

5 Press (SEL).

The clock starts and the next setup display

appears.

6 Press and hold (SEL).

The setup is complete.

To display the clock, press (DSPL). Press

(DSPL) again to return to the previous display.

With the card remote commander

In step 4, to set the hour and minute, press M or m.

Detaching the front panel

You can detach the front panel of this unit to

prevent theft.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel, the

caution alarm will sound for a few seconds.

The alarm will only sound if the built-in

amplifier is used.

1 Press (OFF).

The unit is turned off.

2 Press , then pull it off towards you.

Notes

• Do not drop or put excessive pressure on the front

panel and display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a parked

car or on a dashboard/rear tray.

Attaching the front panel

Engage part A of the front panel with part B of

the unit, as illustrated, and push the left side into

position until it clicks.

Note

Do not put anything on the inner surface of the front

panel.

RESET

button

(OFF)

Inserting the disc in the

unit

1 Open the shutter.

2 Insert the disc label side up.

Playback starts.

3 Close the shutter.

Ejecting the disc

Open the shutter.

2 Push down the shutter until it clicks.

The disc is ejected.

Notes

• While ejecting or inserting the disc, do not close the

shutter. The disc may be caught and damaged.

• The disc may be ejected if you open the shutter

forcefully.

Tip

The disc can be played with the shutter opened or

closed.

Click

Location of controls and basic operations

Main unit

Refer to the pages listed for details.

a Volume +/– button

To adjust volume.

b ATT (attenuate) button

To attenuate the sound. To cancel, press

again.

c DSPL (display)/DIM (dimmer) button

4, 7, 9

To change display items (press); change the

display brightness (press and hold).

d OPEN shutter, disc slot (located behind

the shutter) 5

e Display window

f EQ3 (equalizer) button 8

To select an equalizer type (XPLOD,

VOCAL, CLUB, JAZZ, NEWAGE, ROCK,

CUSTOM or OFF).

g OFF button

To power off/stop the source.

h SEEK +/– button

Radio:

To tune in stations automatically (press); find

a station manually (press and hold).

CD:

To skip tracks (press); skip tracks

continuously (press, then press again within

about 1 second and hold); fast-forward/

reverse a track (press and hold).

i (front panel release) button 4

j SOURCE button

To power on/change the source (Radio/CD/

MD*

k MODE button 7, 10

To select the radio band (FM/AM)/select the

unit*

l SEL (select) button 4, 8, 9

To select items.

m RESET button (located behind the front

panel) 4

n Frequency select switch (located on the

bottom of the unit)

See “Frequency select switch” in the

supplied installation/connections manual.

o Number buttons

Radio:

To receive stored stations (press); store

stations (press and hold).

CD/MD*

(1)/(2): GP*

/DISC*

–/+

To skip groups (press); skip groups

continuously (press and hold).

(3): REP 7, 10

(4): SHUF 7, 10

p SENS/BTM button 7

To improve weak reception: LOCAL/MONO

(press); start the BTM function (press and

hold).

q SCRL button 7

To scroll the display item.

r LIST/CAT*

button 8, 10

To list up.

s Receptor for the card remote

commander

*1 When an MD changer is connected.

*2 When a CD/MD changer is connected.

*3 When an MP3/ATRAC CD is played and a changer

is not connected. If the changer is connected, the

operation is different, see page 10.

*4 When the SAT tuner is connected.

ATT OFF

SOURCE MODE

SEL

SEEK

123456

SENS

REP BTM

–

GP/DISC

SHUF

LISTSCRL

DSPL

DIM

EQ3

OPEN

SEEK

CAT

12 3 4 5 6 7 8

CDX-R30M

9 0 qaqs qd qf qg qh qj qk ql

For details on selecting a CD/MD changer, see

page 10.

Display items

A Source

B Track number/Elapsed playing time,

Disc/artist name, Group number*

Group name, Track name, Text

information*

, Clock

*1 Group number is displayed only when the group is

changed.

*2 When playing an MP3, ID3 tag is displayed and

when playing a ATRAC CD, text information written

by SonicStage, etc is displayed.

To change display items B, press (DSPL);

scroll display items B, press (SCRL) or set

“A.SCRL-ON” (page 9).

Tip

Displayed item will differ, depending on the disc type

and recorded format. For details on MP3, see

page 12; ATRAC CD, see page 13.

Repeat and shuffle play

During playback, press (3) (REP) or

(4) (SHUF) repeatedly until the

desired setting appears.

* When an MP3/ATRAC CD is played.

To return to normal play mode, select “REP-

OFF” or “SHUF-OFF.”

Radio

Storing and receiving

stations

Caution

When tuning in stations while driving, use Best

Tuning Memory (BTM) to prevent an accident.

Storing automatically — BTM

Press (SOURCE) repeatedly until

“TUNER” appears.

To change the band, press (MODE)

repeatedly. You can select from FM1, FM2,

FM3, AM1 or AM2.

2 Press and hold (BTM) until “BTM”

flashes.

The unit stores stations in order of frequency

on the number buttons.

A beep sounds when the setting is stored.

Storing manually

While receiving the station that you

want to store, press and hold a

number button ((1) to (6)) until

“MEM” appears.

The number button indication appears in the

display.

Note

If you try to store another station on the same number

button, the previously stored station will be replaced.

Receiving the stored stations

Select the band, then press a number

button ((1) to (6)).

With the card remote commander

To select preset stations, press M or m.

Tuning automatically

Select the band, then press (SEEK) +/–

to search for the station.

Scanning stops when the unit receives a

station. Repeat this procedure until the

desired station is received.

Tip

If you know the frequency of the station you want to

listen to, press and hold (SEEK) +/– to locate the

approximate frequency, then press (SEEK) +/–

repeatedly to fine adjust to the desired frequency

(manual tuning).

Select To play

REP-TRACK track repeatedly.

REP-GP* group repeatedly.

SHUF-GP* group in random order.

SHUF-DISC disc in random order.

continue to next page t

Receiving a station through a

list — list-up

You can list up the frequency or the name. For

details on labeling a station, see page 9.

1 Select the band, then press (LIST).

The frequency or station name appears.

2 Press (LIST) repeatedly until the

desired station appears.

After 5 seconds, the unit returns to normal

reception mode.

3 Press (S EEK) +/– to receive the

station.

With the card remote commander

In step 2, to select the station, press M or m.

Other functions

Changing the sound

settings

Adjusting the sound

characteristics — BAL/FAD/SUB

You can adjust the balance, fader, and subwoofer

volume.

1 Press (SEL ) repeatedly until “BAL,”

“FAD” or “SUB” appears.

The item changes as follows:

LOW*

t MID*

t HI*

BAL (left-right) t FAD (front-rear) t

SUB (subwoofer volume)*

*1 When EQ3 is activated (page 8).

*2 When the audio output is set to “SUB” (page 9).

“ATT” is displayed at the lowest setting, and can

be adjusted up to 20 steps.

2 Press the volume +/– button

repeatedly to adjust the selected item.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

Note

Adjust within 3 seconds of selecting the item.

With the card remote commander

In step 2, to adjust the selected item, press <, M, ,

or m.

Adjusting the equalizer curve

— EQ3

You can adjust and store the equalizer settings

for different tone ranges.

1 Select a source, then press (EQ3)

repeatedly to select the EQ3 type.

2 Press (SEL ) repeatedly until “LOW,”

“MID” or “HI” appears.

3 Press the volume +/– button

repeatedly to adjust the selected item.

The volume level is adjustable in 1 dB steps,

from –10 dB to +10 dB.

Repeat steps 2 and 3 to adjust the equalizer

curve.

To restore the factory-set equalizer curve,

press and hold ( SEL ) before the setting is

complete.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

With the card remote commander

In step 3, to adjust the selected item, press <, M, ,

or m.

Labeling a station/disc

When you receive a station, or play a disc in a

CD changer with the CUSTOM FILE function,

you can label each station/disc with a custom

name up to 8 characters (Station Memo/Disc

Memo).

If you label a station/disc, the name appears on

the list (page 8 or 10).

1 While receiving a station or playing a

disc that you want to label, press and

hold (LIST).

2 Press the volume +/– button

repeatedly until the desired character

appears.

To move the digital indication, press (SEL).

A y B y C ... y 0 y 1 y 2 ... y +

y – y ... y (blank space) y A

Repeat this operation until the entire name is

entered.

3 Press and hold (LIST).

The labeling is complete and the display

returns to normal play/reception mode.

To display the name, press (DSPL) during

reception or playback.

Tips

• To correct or erase a character, overwrite or enter

“.”

• The Disc Memo always takes priority over any

prerecorded title.

• You can label a disc on the unit if a changer with the

CUSTOM FILE function is connected.

• “REP-TRACK” and all shuffle play are suspended

until the labeling is complete.

With the card remote commander

In step 2, to select the character, press M or m.

Deleting the custom name

1 Select the radio, or the unit that has stored the

custom name you want to delete, then press

and hold (LIST).

2 Press and hold (DSPL).

The stored name will flash.

3 Press the volume +/– button repeatedly to

select the name you want to delete.

4 Press and hold (SEL).

The name is deleted. Repeat steps 3 and 4 to

delete other names.

5 Press and hold (LIST).

The unit returns to normal play/reception

mode.

With the card remote commander

In step 3, to select the name, press M or m.

Adjusting setup items

— SET

1 Press and hold (SEL) .

The setup display appears.

2 Press (SEL) repeatedly until the

desired item appears.

3 Press the volume +/– button to select

the setting (example “ON” or “OFF”).

4 Press and hold (SEL) .

The setup is complete and the display returns

to normal play/reception mode.

Note

Displayed items will differ, depending on the source

and setting.

With the card remote commander

In step 3, to select the setting, press < or ,.

The following items can be set (follow the page

reference for details):

“

z” indicates the default settings.

*1 When the unit is turned off.

*2 When the audio output is set to “SUB.”

CLOCK-ADJ

(Clock Adjust)

(page 4)

BEEP To set “BEEP-ON” (

z) or

“BEEP-OFF.”

SUB/REAR*

To switch the audio output.

–“SUB” (

z): to output to a

subwoofer.

– “REAR”: to output to a

power amplifier.

DIM (Dimmer) To change the brightness of the

display.

–“DIM-ON”: to dim the

display.

– “DIM-OFF” (

z): to

deactivate the dimmer.

DEMO*

(Demonstration)

To set “DEMO-ON” (z) or

“DEMO-OFF.”

A.SCRL

(Auto Scroll)

To scroll long displayed items

automatically when the group/

track is changed.

– “A.SCRL-ON”: to scroll.

– “A.SCRL-OFF” (

z): to not

scroll.

LPF*

(Low

Pass Filter)

To select the cut-off frequency

“78HZ,” “125HZ” or “OFF”

(

z).

Using optional equipment

CD/MD changer

Selecting the changer

1 Press (SOURCE) repeatedly until “CD” or

“MD” appears.

2 Press (MODE) repeatedly until the desired

changer appears.

Playback starts.

Skipping groups and discs

1 During playback press (1)/(2) (GP/DISC)

–/+.

Repeat and shuffle play

1 During playback, press (3) (REP) or (4)

(SHUF) repeatedly until the desired setting

appears.

*1 When one or more CD/MD changers are

connected.

*2 When one or more CD changers, or two or more

MD changers are connected.

To return to normal play mode, select “REP-

OFF” or “SHUF-OFF.”

Tip

“SHUF-ALL” will not shuffle tracks between CD units

and MD changers.

Locating a disc by name — list-up

You can select a disc from the list when

connecting a CD changer with the CUSTOM

FILE function or an MD changer.

If you assign a name to a disc, the name appears

on the list. For details on labeling a disc, see

page 9.

1 During playback, press (LIST).

The disc number or disc name appears.

2 Press (LIST) repeatedly until the desired disc

appears.

After 5 seconds, the unit returns to normal

play mode.

3 Press (SEEK) +/– to play the disc.

With the card remote commander

In step 2, to select the disc, press M or m.

Card remote commander

RM-X114

Location of controls

The corresponding buttons on the card remote

commander control the same functions as those

on this unit.

The following buttons on the card remote

commander have also different buttons/functions

from the unit.

•

</, (SEEK +/–) buttons

To control radio/CD, the same as (SEEK)

+/– on the unit. (For details of other operations,

see “With the card remote commander.”)

• SOUND button

The same as (SEL) on the unit.

•

M/m (DISC*/PRESET +/–) buttons

To control CD, the same as (1)/(2) –/+ on the

unit. (For details of other operations, see “With

the card remote commander.”)

* Not available for this unit.

To skip Press (1)/(2)

group and release (hold for a

moment).

group

continuously

within 2 seconds of first

releasing.

discs repeatedly.

discs

continuously

then, press again within 2

seconds and hold.

Select To play

REP-DISC*

disc repeatedly.

SHUF-

CHGR*

tracks in the changer in random

order.

SHUF-ALL*

tracks in all units in random

order.

Disc numberUnit number

DISC

–

ATTOFF

DSPL MODE

SOURCE

DISC

VOL

–

PRESET

SEEK

–

PRESET –

SOUND

LIST

MODE

LIST

ENTER

ATT

DSPL

SOURCE

</,

(SEEK –/+ )

SOUND

OFF

VOL (+/ –)

m/M

(DISC

PRESET

+/ –)

Note

If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander

unless (SOURCE) on the unit is pressed, or a disc is

inserted to activate the unit first.

Replacing the lithium battery

Under normal conditions, the battery will last

approximately 1 year. (The service life may be

shorter, depending on the conditions of use.)

When the battery becomes weak, the range of the

card remote commander becomes shorter.

Replace the battery with a new CR2025 lithium

battery. Use of any other battery may present a

risk of fire or explosion.

Notes on the lithium battery

• Keep the lithium battery out of the reach of children.

Should the battery be swallowed, immediately

consult a doctor.

• Wipe the battery with a dry cloth to assure a good

contact.

• Be sure to observe the correct polarity when

installing the battery.

• Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Rotary commander RM-X4S

Attaching the label

Attach the indication label depending on how

you mount the rotary commander.

Location of controls

The corresponding buttons on the rotary

commander control the same functions as those

on this unit.

The following controls on the rotary commander

require a different operation from the unit.

• PRESET control

To select preset stations; control CD, the same

as (1)/(2) –/+ on the unit (push in and rotate).

• VOL control

The same as the volume +/– button on the unit

(rotate).

• SEEK/AMS control

The same as (SEEK) +/– on the unit (rotate, or

rotate and hold).

Changing the operative direction

The operative direction of the controls is factory-

set as shown below.

If you need to mount the rotary commander on

the right hand side of the steering column, you

can reverse the operative direction.

1 While pushing the VOL control, press and

hold (SEL).

+ side up

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of

in fire.

DSPL

MODE

OFF

ATT

SEL

SOURCE

DSPL

MODE

OFF

VOL

SEEK/AMS

PRESET

To increase

To decrease

Additional Information

Precautions

• If your car has been parked in direct sunlight,

allow the unit to cool off before operating it.

• Power antenna will extend automatically while

the unit is operating.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit

will not operate properly. In such a case, remove

the disc and wait for about an hour until the

moisture has evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft drinks

onto the unit or discs.

Notes on discs

• To keep a disc clean, do not touch its surface.

Handle the disc by its edge.

• Keep your discs in their cases or disc

magazines when not in use.

• Do not subject discs to heat/high temperature.

Avoid leaving them in a parked car or on a

dashboard/rear tray.

• Do not attach labels, or use discs with sticky

ink/residue. Such discs may stop spinning

when used, causing a malfunction, or may ruin

the disc.

• Do not use any discs with labels or stickers

attached.

The following malfunctions may result from

using such discs:

– Inability to eject a disc (due to a label or

sticker peeling off and jamming the eject

mechanism).

– Inability to read audio data correctly (e.g.,

playback skipping, or no playback) due to

heat shrinking of a sticker or label causing a

disc to warp.

• Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do

not use such discs.

• You cannot play 8 cm (3 in) CDs.

• Before playing, clean the

discs with a commercially

available cleaning cloth. Wipe

each disc from the center out.

Do not use solvents such as

benzine, thinner,

commercially available

cleaners, or antistatic spray

intended for analog discs.

Notes on CD-R/CD-RW discs

• Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the

condition of the disc) may not play on this unit.

• You cannot play a CD-R/a CD-RW that is not

finalized.

Music discs encoded with copyright

protection technologies

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

by some record companies. Please be aware that

among those discs, there are some that do not

conform to the CD standard and may not be

playable by this product.

About MP3 files

MP3, which stands for MPEG-1 Audio Layer-3,

is a music file compression format standard. It

compresses audio CD data to approximately 1/10

of its original size.

• The unit is compatible with the ISO 9660 level

1/level 2 format, Joliet/Romeo in the expansion

format, ID3 tag version 1.0, 1.1, 2.2, 2.3 and

2.4, and Multi Session.

• The maximum number of:

– folders (groups): 150 (including root and

empty folders).

– MP3 files (tracks) and folders contained in a

disc: 300 (if a folder/file names contain many

characters, this number may become less than

300).

– displayable characters for a folder/file name

is 32 (Joliet), or 32/64 (Romeo); ID3 tag is

15/30 characters (1.0, 1.1, 2.2 and 2.3), or 63/

126 characters (2.4).

Note on DualDiscs

A DualDisc is a two sided disc product which

mates DVD recorded material on one side with

digital audio material on the other side. However,

since the audio material side does not conform to

the Compact Disc (CD) standard, playback on this

product is not guaranteed.

Playback order of MP3 files

Notes

• Be sure to finalize the disc before using on the unit.

• When naming an MP3 file, be sure to add the file

expansion “.mp3” to the file name.

• If you play a high-bit-rate MP3, such as 320 kbps,

sound may be intermittent.

• During playback of a VBR (variable bit rate) MP3 file

or fast-forward/reverse, elapsed playing time may

not display accurately.

• When the disc is recorded in Multi Session, only the

first track of the first session format is recognized

and played (any other format is skipped). The

priority of the format is CD-DA, ATRAC CD and

MP3.

– When the first track is a CD-DA, only CD-DA of the

first session is played.

– When the first track is not a CD-DA, an ATRAC CD

or MP3 session is played. If the disc has no data in

any of these formats, “NO MUSIC” is displayed.

About ATRAC CD

ATRAC3plus format

ATRAC3, which stands for Adaptive Transform

Acoustic Coding3, is audio compression

technology. It compresses audio CD data to

approximately 1/10 of its original size.

ATRAC3plus, which is an extended format of

ATRAC3, compresses the audio CD data to

approximately 1/20 of its original size. The unit

accepts both ATRAC3 and ATRAC3plus format.

ATRAC CD

ATRAC CD is recorded audio CD data which is

compressed to ATRAC3 or ATRAC3plus format

using authorized software, such as SonicStage

2.0 or later, or SonicStage Simple Burner.

• The maximum number of:

– folders (groups): 255

– files (tracks): 999

• The characters for a folder/file name and text

information written by SonicStage is displayed.

For details on ATRAC CD, see the SonicStage or

SonicStage Simple Burner manual.

Note

Be sure to create the ATRAC CD using authorized

software, such as SonicStage 2.0 or later, or

SonicStage Simple Burner 1.0 or 1.1.

If you have any questions or problems

concerning your unit that are not covered in this

manual, consult your nearest Sony dealer.

Maintenance

Fuse replacement

When replacing the fuse, be

sure to use one matching the

amperage rating stated on the

original fuse. If the fuse

blows, check the power

connection and replace the

fuse. If the fuse blows again

after replacement, there may

be an internal malfunction. In

such a case, consult your

nearest Sony dealer.

Cleaning the connectors

The unit may not function properly if the

connectors between the unit and the front panel

are not clean. In order to prevent this, detach the

front panel (page 4) and clean the connectors

with a cotton swab dipped in alcohol. Do not

apply too much force. Otherwise, the connectors

may be damaged.

Notes

• For safety, turn off the ignition before cleaning the

connectors, and remove the key from the ignition

switch.

• Never touch the connectors directly with your fingers

or with any metal device.

Folder

(group)

MP3 file

(track)

MP3

Fuse (10A)

Main unit Back of the front panel

Removing the unit

1 Remove the protection collar.

1 Detach the front panel (page 4).

2 Engage the release keys together with the

protection collar.

3 Pull out the release keys to remove the

protection collar.

2 Remove the unit.

1 Insert both release keys simultaneously

until they click.

2 Pull the release keys to unseat the unit.

3 Slide the unit out of the mounting.

Specifications

CD Player section

Signal-to-noise ratio: 120 dB

Frequency response: 10 – 20,000 Hz

Wow and flutter: Below measurable limit

Tuner section

Tuning range:

87.5 – 108.0 MHz (at 50 kHz step)

87.5 – 107.9 MHz (at 200 kHz step)

FM tuning interval: 50 kHz/200 kHz switchable

Antenna terminal: External antenna connector

Intermediate frequency: 10.7 MHz/450 kHz

Usable sensitivity: 9 dBf

Selectivity: 75 dB at 400 kHz

Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)

Harmonic distortion at 1 kHz: 0.5 % (stereo),

0.3 % (mono)

Separation: 35 dB at 1 kHz

Frequency response: 30 – 15,000 Hz

Tuning range:

531 – 1,602 kHz (at 9 kHz step)

530 – 1,710 kHz (at 10 kHz step)

AM tuning interval: 9 kHz/10 kHz switchable

Antenna terminal: External antenna connector

Intermediate frequency: 10.7 MHz/450 kHz

Sensitivity: 30 µV

Power amplifier section

Outputs: Speaker outputs (sure seal connectors)

Speaker impedance: 4 – 8 ohms

Maximum power output: 52 W × 4 (at 4 ohms)

General

Outputs:

Audio outputs terminal (sub/rear switchable)

Power antenna relay control terminal

Power amplifier control terminal

Inputs:

BUS control input terminal

BUS audio input terminal

Remote controller input terminal

Antenna input terminal

Tone controls:

Low: ±10 dB at 60 Hz (XPLOD)

Mid: ±10 dB at 1 kHz (XPLOD)

High: ±10 dB at 10 kHz (XPLOD)

Orient the release

keys as shown.

Hook facing

inwards.

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC

DISTORTION

23.2 watts per channel minimum continuous

average power into 4 ohms, 4 channels driven

from 20 Hz to 20 kHz with no more than 5% total

harmonic distortion.

CEA2006 Standard

Power Output: 17 Watts RMS × 4 at

4 Ohms < 1% THD+N

SN Ratio: 82 dBA

(reference: 1 Watt into 4 Ohms)

Power requirements: 12 V DC car battery

(negative ground)

Dimensions: Approx. 178 × 50 × 179 mm

/8 × 2 × 7

/8 in) (w/h/d)

Mounting dimensions: Approx. 182 × 53 × 161 mm

/4 × 2

/8 × 6

/8 in) (w/h/d)

Mass: Approx. 1.2 kg (2 1b 10 oz)

Supplied accessory:

Parts for installation and connections (1 set)

Optional accessories/equipment:

Card remote commander: RM-X114

Rotary commander: RM-X4S

Marine remote commander: RM-X55M

Bus cable (supplied with an RCA pin cord):

RC-61 (1 m), RC-62 (2 m)

CD changer (10 discs): CDX-757MX

CD changer (6 discs): CDX-T69

Source selector: XA-C30, XA-C40

AUX-IN selector: XA-300

Your dealer may not handle some of the above listed

accessories. Please ask the dealer for detailed

information.

Note

This unit cannot be connected to a digital preamplifier

or an equalizer which is Sony BUS system compatible.

Design and specifications are subject to change

without notice.

• Lead-free solder is used for soldering certain parts.

(more than 80 %)

• Halogenated flame retardants are not used in the

certain printed wiring boards.

• Halogenated flame retardants are not used in

cabinets.

• Packaging cushions do not use polystyrene foam.

Troubleshooting

The following checklist will help you remedy

problems you may encounter with your unit.

Before going through the checklist below, check

the connection and operating procedures.

General

No power is being supplied to the unit.

• Check the connection. If everything is in order,

check the fuse.

• If the unit is turned off and the display

disappears, it cannot be operated with the

remote commander.

t Turn on the unit.

US and foreign patents licensed from Dolby

Laboratories.

MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and Thomson.

The power antenna does not extend.

The power antenna does not have a relay box.

No sound.

• The volume is too low.

• The ATT function is activated.

• The position of the fader control (FAD) is not

set for a 2-speaker system.

• The CD changer is incompatible with the disc

format (MP3/ATRAC CD).

t Play back with a Sony MP3 compatible CD

changer, or this unit.

No beep sound.

• The beep sound is canceled (page 9).

• An optional power amplifier is connected and

you are not using the built-in amplifier.

The contents of the memory have been

erased.

• The RESET button has been pressed.

t Store again into the memory.

• The power connecting lead or battery has been

disconnected.

• The power connecting lead is not connected

properly.

Stored stations and correct time are erased.

The fuse has blown.

Makes noise when the position of the

ignition key is switched.

The leads are not matched correctly with the

car’s accessory power connector.

The display disappears from/does not

appear in the display window.

• The dimmer is set “DIM-ON” (page 9).

• The display disappears if you press and hold

(OFF).

t Press and hold (OFF) again until the

display appears.

• The connectors are dirty (page 13).

CD/MD playback

The disc is automatically ejected.

The disc has trouble.

t Check the following:

The disc cannot be loaded.

• Another disc is already loaded.

• The disc has been forcibly inserted upside

down or in the wrong way.

The disc does not playback.

• Defective or dirty disc.

• The CD-Rs/CD-RWs are not for audio use

(page 12).

MP3 files cannot be played back.

The disc is incompatible with the MP3 format

and version (page 12).

continue to next page t

Error displays/Messages

MP3 files take longer to play back than

others.

The following discs take a longer time to start

playback.

– a disc recorded with a complicated tree

structure.

– a disc recorded in Multi Session.

– a disc to which data can be added.

The ATRAC CD cannot play.

• The disc is not created by authorized software,

such as SonicStage or SonicStage Simple

Burner.

• Tracks that are not included in the group cannot

be played.

The display items do not scroll.

• For discs with very many characters, those may

not scroll.

• “A.SCRL” is set to off.

t Set “A.SCRL-ON” (page 9) or press

(SCRL).

The sound skips.

• Installation is not correct.

t Install the unit at an angle of less than

45° in a sturdy part of the car.

• Defective or dirty disc.

The operation buttons do not function.

The disc will not eject.

Press the RESET button (page 4).

Radio reception

The stations cannot be received.

The sound is hampered by noises.

• Connect a power antenna control lead (blue) or

accessory power supply lead (red) to the power

supply lead of a car’s antenna booster (only

when your car has built-in FM/AM antenna in

the rear/side glass).

• Check the connection of the car antenna.

• The auto antenna will not go up.

t Check the connection of the power antenna

control lead.

• Check the frequency.

Preset tuning is not possible.

• Store the correct frequency in the memory.

• The broadcast signal is too weak.

Automatic tuning is not possible.

• Setting of the local seek mode is not correct.

t Tuning stops too frequently:

Press (SENS) until “LOCAL-ON” appears.

t Tuning does not stop at a station:

Press (SENS) repeatedly until “MONO-

ON” or “MONO-OFF” (FM), or “LOCAL-

OFF” (AM) appears.

• The broadcast signal is too weak.

t Perform manual tuning.

During FM reception, the “ST” indication

flashes.

• Tune in the frequency accurately.

• The broadcast signal is too weak.

t Press (SENS) to set the monaural reception

mode to “MONO-ON.”

An FM program broadcast in stereo is heard

in monaural.

The unit is in monaural reception mode.

t Press (SENS) “MONO-OFF” appears.

BLANK*

Tracks have not been recorded on the MD.*

t Play an MD with recorded tracks.

ERROR*

• The disc is dirty or inserted upside down.*

t Clean or insert the disc correctly.

• The disc cannot play because of some problem.

t Insert another disc.

FAILURE (Illuminates until any button is pressed.)

The connection of speakers/amplifiers is

incorrect.

t See the installation guide manual of this

model to check the connection.

FAILURE (Illuminates for about 1 second.)

When the XM tuner is connected, storing an

XM radio channel into a preset failed.

t Be sure to receive the channel that you

want to store, then try it again.

LOAD

The changer is loading the disc.

t Wait until loading is complete.

L.SEEK +/–

The local seek mode is on during automatic

tuning.

NO DATA

All custom names have been deleted, or none are

stored.

NO DISC

The disc is not inserted in the CD/MD changer.

t Insert discs in the changer.

NO ID3

ID3 tag information is not written in the MP3

file.

NO INFO

Text information is not written in the ATRAC3/

ATRAC3plus file.

NO MAG

The disc magazine is not inserted in the CD

changer.

t Insert the magazine in the changer.

*1 If an error occurs during playback of a CD or MD,

the disc number of the CD or MD does not appear

in the display.

*2 The disc number of the disc causing the error

appears in the display.

If these solutions do not help improve the

situation, consult your nearest Sony dealer.

If you take the unit to be repaired because of CD

playback trouble, bring the disc that was used at

the time the problem began.

NO MUSIC

The disc is not a music file.

t Insert a music CD in this unit or MP3

playable changer.

NO NAME

A track/group/disc name is not written in the

track.

NOT READ

The disc information has not been read by the

unit.

t Loading the disc, then select it on the list.

NOTREADY

The lid of the MD changer is open or the MDs

are not inserted properly.

t Close the lid or insert the MDs properly.

OFFSET

There may be an internal malfunction.

t Check the connection. If the error indication

remains on in the display, consult your

nearest Sony dealer.

READ

The unit is reading all track and group

information on the disc.

t Wait until reading is complete and playback

starts automatically. Depending on the disc

structure, it may take more than a minute.

RESET

The CD unit and CD/MD changer cannot be

operated because of some problem.

t Press the RESET button (page 4).

“” or “”

During fast-forward or reverse, you have reached

the beginning or the end of the disc and you

cannot go any further.

“”

The character cannot be displayed with the unit.

Félicitations !

Nous vous remercions d’avoir fait l’acquisition

de ce lecteur de disques compacts Sony. Ce

lecteur vous offre les fonctions suivantes.

• Lecture de CD :

Vous pouvez lire des CD-DA (contenant

également des informations CD TEXT*), des

CD-R/CD-RW (fichiers MP3 contenant

également des enregistrements en multisessions

(page 14)) et des CD ATRAC (au format

ATRAC3 et ATRAC3plus (page 14)).

• Réception radio :

– Vous pouvez mémoriser jusqu’à 6 stations par

bande de fréquences (FM1, FM2, FM3, AM1

et AM2).

– Fonction BTM (mémorisation des meilleurs

accords) : l’appareil sélectionne des stations

émettant un signal fort et les mémorise.

– Vous pouvez attribuer un nom à chaque

station de radio, le sauvegarder dans la

mémoire et afficher les noms de station dans

la liste.

• Utilisation d’appareils en option

Cet appareil vous permet, en plus de la lecture,

de commander des changeurs CD ou MD

externes.

* Un disque CD TEXT est un CD-DA contenant des

informations telles que le nom du disque, de l’artiste

et des plages.

L’appellation et le logo SonicStage sont des

marques de commerce de Sony Corporation.

ATRAC, ATRAC3, ATRAC3plus et leurs logos

sont des marques de commerce de Sony

Corporation.

Type de disques

Symbole indiqué sur le

disque

CD-DA

MP3

CD ATRAC

En ce qui concerne l’installation et les

connexions, consulter le manuel

d’installation/raccordement fourni.

ATTENTION

L’utilisation d’instruments optiques

avec ce produit augmente les risques

pour les yeux.

Avertissement si le contact de votre

véhicule ne comporte pas de position

ACC

Après avoir coupé le moteur, n’oubliez pas de

maintenir la touche (OFF) enfoncée sur

l’appareil jusqu’à ce que l’affichage

disparaisse.

Sinon, l’affichage n’est pas désactivé et la

batterie du véhicule se décharge.

Cette étiquette est située sur la partie inférieure

du châssis.

Le logo « SAT Radio Ready »

indique que ce produit

commande un module tuner

radio satellite (vendu

séparément). Consultez votre détaillant agréé

Sony le plus proche pour en savoir plus sur le

fonctionnement du module tuner radio satellite.

« SAT Radio », « SAT Radio Ready », les logos

SAT Radio et SAT Radio Ready, ainsi que

toutes les marques associées sont des marques de

commerce de Sirius Satellite Radio Inc. et de

XM Satellite Radio Inc.

Table des matières

Préparation

Réinitialisation de l’appareil . . . . . . . . . . . . . . . 4

Réglage de l’horloge . . . . . . . . . . . . . . . . . . . . . 4

Retrait de la façade . . . . . . . . . . . . . . . . . . . . . . 4

Installation de la façade . . . . . . . . . . . . . . . . 4

Insertion du disque dans l’appareil . . . . . . . . . . 5

Éjection du disque . . . . . . . . . . . . . . . . . . . . 5

Emplacement des commandes et

opérations de base

Appareil principal . . . . . . . . . . . . . . . . . . . . 6

Rubriques d’affichage . . . . . . . . . . . . . . . . . 7

Lecture répétée et lecture aléatoire . . . . . . . 7

Radio

Réception et mémorisation des stations . . . . . . 7

Mémorisation automatique

— BTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mémorisation manuelle . . . . . . . . . . . . . . . . 7

Réception des stations mémorisées . . . . . . . 7

Recherche automatique des fréquences . . . . 8

Réception d’une station à partir d’une liste

— Affichage automatique des titres . . . . . . 8

Autres fonctions

Modification des réglages du son . . . . . . . . . . . 8

Réglage des caractéristiques du son

— BAL/FAD/SUB . . . . . . . . . . . . . . . . . . . 8

Réglage de la courbe de l’égaliseur

— EQ3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Identification d’une station

ou d’un disque. . . . . . . . . . . . . . . . . . . . . . . . . . 9

Réglage des paramètres de configuration

— SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Si vous utilisez un appareil en option. . . . . . . 10

Changeur de CD/MD . . . . . . . . . . . . . . . . 10

Mini-télécommande RM-X114 . . . . . . . . . 11

Satellite de commande RM-X4S . . . . . . . . 12

Informations complémentaires

Précautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Remarques sur les disques . . . . . . . . . . . . 13

À propos des fichiers MP3 . . . . . . . . . . . . 14

À propos des CD ATRAC . . . . . . . . . . . . . 14

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Démontage de l’appareil. . . . . . . . . . . . . . . . . 15

Caractéristiques techniques. . . . . . . . . . . . . . . 16

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Affichage des erreurs/messages . . . . . . . . 18

Préparation

Réinitialisation de

l’appareil

Avant la première mise en service de l’appareil,

après avoir remplacé la batterie du véhicule ou

modifié les raccordements, vous devez

réinitialiser l’appareil.

Retirez la façade, puis appuyez sur la touche

RESET avec un objet pointu comme un stylo à

bille.

Remarque

Une pression sur la touche RESET remet l’heure à

zéro et efface certaines informations mémorisées.

Réglage de l’horloge

L’horloge numérique fonctionne suivant un cycle

de 12 heures.

1 Appuyez sur la touche (SEL) et

maintenez-la enfoncée.

L’écran de configuration apparaît.

2 Appuyez plusieurs fois sur (SEL)

jusqu’à ce que « CLOCK-ADJ »

apparaisse.

3 Appuyez sur (DSPL).

L’indication des heures clignote.

4 Appuyez sur la touche de volume +/–

pour régler l’heure et les minutes.

Appuyez sur (DSPL) pour déplacer

l’indication numérique.

5 Appuyez sur (SEL).

L’horloge démarre et l’écran de configuration

suivant apparaît.

6 Appuyez sur la touche (SEL) et

maintenez-la enfoncée.

La configuration est terminée.

Appuyez sur (DSPL) pour afficher l’horloge.

Appuyez de nouveau sur (D SPL) pour revenir à

l’écran précédent.

Avec la mini-télécommande

Appuyez sur M ou m à l’étape 4 pour régler l’heure et

les minutes.

Retrait de la façade

Vous pouvez retirer la façade de cet appareil pour

le protéger du vol.

Alarme d’avertissement

Si vous mettez la clé de contact en position OFF

sans ôter la façade, l’alarme d’avertissement

retentit pendant quelques secondes.

L’alarme est émise uniquement lorsque

l’amplificateur intégré est utilisé.

1 Appuyez sur (OFF).

L’appareil est mis hors tension.

2 Appuyez sur , puis sortez la façade

en tirant vers vous.

Remarques

• N’exercez pas de pression excessive sur la façade

ni la fenêtre d’affichage et ne l’échappez pas.

• N’exposez pas la façade à une température ou à un

taux d’humidité élevé. Évitez de la laisser dans un

véhicule en stationnement ou sur le tableau de bord

ou la plage arrière.

Installation de la façade

Insérez la partie A de la façade dans la partie B

de l’appareil, tel qu’illustré, puis poussez sur le

côté gauche jusqu’au déclic indiquant qu’il est en

position.

Remarque

Ne posez rien sur la face interne de la façade.

Touche

RESET

(OFF)

La page charge ...

Sony CDX-R30M Manuel utilisateur

Marque: Sony

Modèle: CDX-R30M

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sony CDX-R30M User manual

Sony CDX-R30M Manuel utilisateur

Sony CDX-R30M Manuel utilisateur

dans d''autres langues

Documents connexes