Maytag MED5630HW Guide d'installation

DRYER INSTALLATION INSTRUCTIONS

INSTRUCTIONS POUR L’INSTALLATION

DE LA SÉCHEUSE

Para una version de estas instrucciones en español, visite www.whirlpool.com

Table of Contents Table des matières

W11183136B

W11183139B-SP

INSTALLATION NOTES

Date of purchase: ________________________________________

Date of installation: _______________________________________

Installer: _________________________________________________

Model number: ___________________________________________

Serial number: ____________________________________________

NOTES CONCERNANT L’INSTALLATION

Date d’achat: ____________________________________________

Date d’installation: ________________________________________

Installateur: ______________________________________________

Numéro de modéle: _______________________________________

Numéro de série: _________________________________________

DRYER SAFETY ....................................................................... 2

INSTALLATION REQUIREMENTS ........................................... 4

Tools and Parts ..................................................................................4

LOCATION REQUIREMENTS .................................................. 5

ELECTRICAL REQUIREMENTS – U.S.A. ONLY ..................... 7

ELECTRIC DRYER POWER HOOKUP – CANADA ONLY ...... 8

GAS DRYER POWER HOOKUP .............................................. 8

INSTALL LEVELING LEGS ..................................................... 10

MAKE ELECTRICAL CONNECTION – U.S.A. ONLY ............ 11

Power Supply Cord Connection ...................................................11

4-Wire Power Supply Cord Connection ......................................12

MAKE GAS CONNECTION .................................................... 17

VENTING ................................................................................. 18

Venting Requirements ....................................................................18

Plan Vent System ............................................................................ 19

Install Vent System .......................................................................... 20

CONNECT INLET HOSE ....................................................... 21

CONNECT VENT .................................................................... 22

LEVEL DRYER ........................................................................ 23

COMPLETE INSTALLATION CHECKLIST............................. 23

DOOR REVERSAL (OPTIONAL) ............................................ 24

SÉCURITÉ DE LA SÉCHEUSE .............................................. 30

EXIGENCES D’INSTALLATION ............................................. 32

Outillage et pièces ........................................................................32

EXIGENCES D’EMPLACEMENT ........................................... 33

SÉCHEUSE ÉLECTRIQUE RACCORDEMENT

À L’ALIMENTATION ÉLECTRIQUE –

CANADA SEULEMENT .......................................................... 36

RACCORDEMENT D’UNE SÉCHEUSE À GAZ .................... 37

INSTALLATION DES PIEDS DE NIVELLEMENT .................. 38

RACCORDEMENT AU GAZ ................................................... 39

ÉVACUATION ......................................................................... 40

Exigences concernant l’évacuation ................................. 40

Planification du système d’évacuation ............................ 41

Installation du système d’évacuation .............................. 42

RACCORDEMENT DU TUYAU D’ALIMENTATION

(MODÈLE À VAPEUR UNIQUEMENT) .................................. 43

RACCORDEMENT DU CONDUIT D’ÉVACUATION ............. 44

RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE ..................... 45

ACHEVER L’INSTALLATION LISTE DE VÉRIFICATION ....... 45

INVERSION DE LA PORTE (FACULTATIF) ............................ 46

2

DRYER SAFETY

3

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property

damage.

–

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

–

Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Clear the room, building, or area of all occupants.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•

If you cannot reach your gas supplier, call the fire department.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed for all installations:

Level

Tape measure

Flat-blade screwdriver

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

Tin snips (new vent

installations)

Caulking gun and

compound (new vent

installations)

1/4" (6 mm) and

5/16" (8 mm) nut driver

(recommended)

Utility knife

Wire stripper

(direct wire installations)

Leveling legs (4)

Tools needed for gas installations:

8" (203 mm) or 10"

(254 mm) pipe wrench

8" (203 mm) or 10" (254 mm)

adjustable wrench (for gas

connections)

Pipe-joint compound

resistant to propane gas

“Y” connector

Parts package is located in dryer drum. Check that all parts are

included.

NOTE: Do not use leveling legs supplied with dryer if installing

with a pedestal or a stack kit.

Parts supplied (all models):

Parts needed (steam models):

2' (0.6 m) inlet hose

5' (1.52 m) inlet hose

Parts needed (not supplied with dryer):

■

Vent clamps

■

Vent elbows and vent work

Rubber washer

#2 Phillips screwdriver

Pliers

5

Additional parts may be required, depending on your installation.

Check local codes. Check existing electrical supply and venting.

Read “Electrical Requirements” and “Venting Requirements”

before purchasing parts.

If using a power supply cord:

Use a UL Listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■

A UL Listed 30 A power supply cord, rated 120/240 V

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned

ends.

■

A UL Listed strain relief.

Optional Equipment (not supplied with dryer):

Refer to your Use and Care Guide for information about

accessories available for your dryer.

LOCATION REQUIREMENTS

Check code requirements. Some codes limit, or do not permit,

installing dryer in garages, closets, mobile homes, or sleeping

quarters. Contact your local building inspector.

You will need:

■

A location allowing for proper exhaust installation.

See “Venting Requirements.”

■

A separate 15 or 20 A circuit for a gas dryer or 30 A circuit for

an electric dryer.

■

If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer.

See “Electrical Requirements.”

■

Floor must support dryer weight of 200 lbs. (90.7 kg). Also

consider weight of companion appliance.

■

Cold water faucets located within 4 ft. (1.2 m) of the water

ll valves, and water pressure of 20–120 psi (138–827 kPa).

You may use your washer’s water supply by purchasing the

necessary parts noted in “Parts needed.”

■

Level oor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), install Extended

Dryer Feet Kit, Part Number 279810. If not level, clothes may

not tumble properly and automatic sensor cycles may not

operate correctly.

■

For garage installation, place dryer at least 18" (460 mm)

above oor. If using a pedestal, you will need 18" (460 mm) to

bottom of dryer.

■

The dryer must not be installed or stored in an area where it

will be exposed to water and/or weather.

IMPORTANT: Do not operate, install, or store dryer where it

will be exposed to water, weather, or at temperatures below

40°F (4°C). Lower temperatures may cause dryer not to shut

off at end of automatic sensor cycles, resulting in longer drying

times.

Side view:

Front view:

DRYER DIMENSIONS

*Approx. measurement

Maytag

®

Models

Whirlpool

®

Models

*Approx. measurement

6

Back view:

*Approx. measurement

Recommended installation clearances (dryer only):

0" (0 mm) rear spacing is allowed for straight back venting only.

For steam models only, inlet hose must not be kinked.

Custom under-counter installation:

NOTE: Most installations require a minimum of 5" (127 mm)

clearance behind dryer for exhaust vent with elbow. See “Venting

Requirements.”

Installation Clearances

For each arrangement, consider allowing more space for ease of

installation and servicing, spacing for companion appliances, and

clearances for walls, doors, and oor moldings. Space must be

large enough to allow door to fully open. Add spacing on all sides

of dryer to reduce noise transfer. If a closet door or louvered door

is installed, top and bottom air openings in door are required.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

Installation spacing for recessed area or closet

installation

All dimensions show recommended and minimum spacing

allowed.

■

Additional spacing should be considered for ease of

installation and servicing.

■

Additional clearances might be required for wall, door, oor

moldings, dryer venting, and gas line.

■

Additional spacing should be considered on all sides of the

dryer to reduce noise transfer.

■

For closet installation with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

■

Companion appliance spacing should also be considered.

Mobile home – Additional installation requirements:

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile home construction and

Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH.

Mobile home installations require:

■

Metal exhaust system hardware, available for purchase

from your dealer. For further information, see “Assistance or

Service” in your Use and Care Guide.

■

Special provisions must be made in mobile homes to

introduce outside air into dryer. Openings (such as a nearby

window) should be at least twice as large as dryer exhaust

opening.

For mobile home installation of gas dryers:

■

Mobile Home Installation Hold-down Kit Part Number 346764

is available to order. For further information, see “Assistance

or Service” in your Use and Care Guide.

Water inlet

(Steam Models Only)

Vent

Gas

7

ELECTRICAL REQUIREMENTS –

U.S.A. ONLY

It is your responsibility:

■

To contact a qualied electrical installer.

■

To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA 70

– latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

■

To supply the required 3 or 4 wire, single-phase, 120/240 V,

60 Hz, AC-only electrical supply (or 3 or 4 wire, 120/208 V

electrical supply, if specied on the serial/rating plate) on a

separate 30 A circuit, fused on both sides of the line. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

■

Do not use an extension cord.

■

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■

This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor. The green ground wire of the 4-wire power cord

must be secured to the dryer cabinet with the green ground

screw.

■

If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see “Optional External Ground for

3-Wire Connection” in the “Power Supply Cord Connection”

section.

■

A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations

after 1996, (2) mobile homes, (3) recreational vehicles, and (4)

areas where local codes prohibit grounding through the neutral

conductors.

If using a power supply cord:

Use a UL Listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■

A UL Listed 30 A power supply cord, rated 120/240 V

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned

ends.

■

A UL Listed strain relief.

Then choose a 3-wire power supply cord with

ring or spade terminals and UL listed strain

relief. The 3-wire power supply cord, at least

4 ft. (1.22 m) long, must have three 10-gauge

copper wires and match a 3-wire receptacle of

NEMA Type 10-30R.

4-wire receptacle

(14-30R)

3-wire receptacle

(10-30R)

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

■

Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with exible metallic conduit. All

current-carrying wires must be insulated.

■

10-gauge solid copper wire (do not use aluminum) at least

5 ft. (1.52 m) long.

If your outlet looks like this:

Then choose a 4-wire power supply cord with

ring or spade terminals and UL Listed strain

relief. The 4-wire power supply cord, at least

4 ft. (1.22 m) long, must have four 10-gauge

copper wires and match a 4-wire receptacle of

NEMA Type 14-30R. The ground wire (ground

conductor) may be either green or bare. The

neutral conductor must be identified by a white

cover.

8

ELECTRIC DRYER POWER HOOKUP –

CANADA ONLY

ELECTRICAL REQUIREMENTS

It is your responsibility:

■

To contact a qualied electrical installer.

■

To be sure that the electrical connection is adequate and in

conformance with Canadian Electrical Code, C22.1 – latest

edition and all local codes. A copy of above codes standard

may be obtained from: Canadian Standards Association,

178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

■

To supply the required 4-wire, single-phase, 120/240 V, 60 Hz,

AC-only electrical supply on a separate 30 A circuit, fused on

both sides of the line. A time-delay fuse or circuit breaker is

recommended. Connect to an individual branch circuit.

■

This dryer is equipped with a UL Listed and/

or CSA International Certied Power Cord

intended to be plugged into a standard

14-30R wall receptacle. The cord is

5 ft. (1.52 m) long. Be sure wall receptacle

is within reach of dryer’s nal location.

If using a replacement power supply cord, it

is recommended that you use Power Supply

Cord Replacement Part Number 8529008.

For further information, please reference service numbers located

in the “Assistance or Service” section of your Use and Care

Guide.

GAS DRYER POWER HOOKUP

ELECTRICAL REQUIREMENTS

■

120 V, 60 Hz, AC-only, 15 or 20 A fused electrical supply is

required. A time-delay fuse or circuit breaker is recommended.

It is also recommended that a separate circuit serving only this

dryer be provided.

4-wire receptacle

(14-30R)

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

epresentative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

oper outlet

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

epresentative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

oper outlet

9

A. 3/8" flexible gas connector

B. 3/8" pipe to flare adapter fitting

C. 1/8" NPT minimum plugged tapping

D. 1/2" NPT gas supply line

E. Gas shut-off valve

GAS SUPPLY REQUIREMENTS

GAS TYPE

Natural Gas:

This dryer is equipped for use with natural gas. It is certied by

UL for use with propane gas with appropriate conversion.

■

Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate in

the door well of your dryer. If this information does not agree

with the type of gas available, contact your dealer or call the

phone numbers referenced in the “Assistance or Service”

section of your Use and Care Guide.

Propane Gas Conversion:

IMPORTANT: Conversion must be made by a qualied

technician.

No attempt shall be made to convert the appliance from the gas

specied on the model/serial rating plate for use with a different

gas without consulting your gas company.

GAS SUPPLY LINE

Option 1 (Recommended Method)

Flexible stainless steel gas connector:

■

If local codes permit, use a new exible stainless steel gas

connector (Design Certied by the American Gas Association

or CSA International) to connect your dryer to the rigid gas

supply line. Use an elbow and a 3/8" are x 3/8" NPT adapter

tting between the stainless steel gas connector and the dryer

gas pipe, as needed, to prevent kinking.

Option 2 (Alternate Method)

Approved aluminum or copper tubing:

■

Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer. See illustration below.

■

1/2" IPS pipe is recommended.

■

3/8" approved aluminum or copper tubing is acceptable for

lengths under 20 ft. (6.1 m) if local codes and gas supplier

permit.

■

If you are using natural gas, do not use copper tubing.

■

Lengths over 20 ft. (6.1 m) should use larger tubing and a

different size adapter tting.

■

If your dryer has been converted to use propane gas, 3/8"

propane compatible copper tubing can be used. If the total

length of the supply line is more than 20 ft. (6.1 m), use larger

pipe.

NOTE: Pipe-joint compounds that resist the action of propane

gas must be used. Do not use TEFLON

®†

tape.

■

Must include shut-off valve.

In the U.S.A.:

An individual manual shut-off valve must be installed

within six (6) ft. (1.8 m) of the dryer in accordance with

the National Fuel Gas Code, ANSI Z223.1. The location

should be easy to reach for opening and closing.

In Canada:

An individual manual shut-off valve must be installed in

accordance with the B149.1, Natural Gas and Propane

Installation Code. It is recommended that an individual

manual shut-off valve be installed within six (6) ft. (1.8 m)

of the dryer. The location should be easy to reach for

opening and closing.

†

®

TEFLON is a registered trademark of Chemours.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

10

INSTALL LEVELING LEGS

GAS SUPPLY CONNECTION REQUIREMENTS

■

Use an elbow and a 3/8" are x 3/8" NPT adapter tting

between the exible gas connector and the dryer gas pipe,

as needed to avoid kinking.

■

Use only pipe-joint compound. Do not use TEFLON

®

tape.

■

This dryer must be connected to the gas supply line with a

listed exible gas connector that complies with the standard

for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

BURNER INPUT REQUIREMENTS

Elevations above 2,000 ft. (610 m):

■

When installed above 2,000 ft. (610 m) a 4% reduction of the

burner Btu rating shown on the model/serial number plate is

required for each 1,000 ft. (305 m) increase in elevation.

Gas supply pressure testing

■

The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2 psi.

DRYER GAS PIPE

■

The gas pipe that comes out through the rear of your dryer has

a 3/8" male pipe thread.

* NOTE: If the dryer is mounted on a pedestal, the gas

pipe height must be an additional 10" (254 mm) or

15.5" (394 mm) from the oor, depending on the pedestal

model. For a garage installation, the gas pipe height must

be an additional 18" (460 mm) from the oor.

1. Prepare dryer for leveling legs

To avoid damaging oor, use a large at piece of cardboard from

dryer carton; place under entire back edge of dryer. Firmly grasp

dryer body (not console panel) and gently lay dryer down on

cardboard.

Examine leveling legs and locate the diamond marking. Screw

legs into leg holes by hand – use a wrench to nish turning legs

until diamond marking is no longer visible.

Place a carton corner post from dryer packaging under each of

the two dryer back corners. Stand the dryer up. Slide the dryer

on the corner posts until it is close to its nal location. Leave

enough room to connect the exhaust vent.

3/8" NPT dryer gas pipe

2. Screw in leveling legs

Diamond

marking

11

MAKE ELECTRICAL CONNECTION –

U.S.A. ONLY

ELECTRICAL CONNECTION

1. Choose electrical connection type

Power supply cord 4-wire receptacle

(NEMA Type 14-30R).

Go to “Power Supply Cord Connection.”

3-wire direct connection:

Go to “Direct Wire Connection.”

4-wire direct connection:

Go to “Direct Wire Connection.”

Power supply cord 3-wire receptacle

(NEMA Type 10-30R).

Go to “Power Supply Cord Connection.”

NOTE: If local codes do not permit connection of a

cabinet-ground conductor to neutral wire, go to “Optional

External Ground for 3-Wire Connection.” This connection

may be used with either a power supply cord or a direct

wire connection.

Before you start: disconnect power.

Remove hold-down screw and terminal block cover.

2. Remove terminal block cover

Power Supply Cord Connection

Power supply cord strain relief

1. Attach power supply cord strain relief

Remove the screws from a 3/4" (19 mm) UL Listed strain relief.

Put the tabs of the two clamp sections (C) into the hole below the

terminal block opening (B) so that one tab is pointing up (A) and the

other is pointing down (D), and hold in place. Tighten strain relief

screws just enough to hold the two clamp sections (C) together.

Power Supply Cord:

12

1. Prepare to connect neutral ground

wire and neutral wire

Remove center terminal block screw (B). Remove neutral ground

wire (E) from green external ground conductor screw (A).

2. Connect neutral ground wire

and neutral wire

Connect neutral ground wire (E) and neutral wire (white or center)

(C) of power supply cord under center terminal block screw (B).

Tighten screw.

3. Connect ground wire

Connect ground wire (F) (green or bare) of power supply cord

under green external ground conductor screw (A). Tighten screw.

4-Wire Power Supply Cord Connection

4-wire receptacle

(NEMA type 14-30R)

4 prong plug

Spade terminals

with upturned ends

Ring terminals

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

2. Attach power supply cord

to strain relief

Put power supply cord through the strain relief. Be sure that the

wire insulation on the power supply cord is inside the strain relief.

The strain relief should have a tight fit with the dryer cabinet and

be in a horizontal position. Do not further tighten strain relief

screws at this point.

Power supply cord 4-wire receptacle

(NEMA Type 14-30R):

Go to “4-Wire Power Supply Cord

Connection” on this page.

If your outlet looks like this:

Power supply cord 3-wire receptacle

(NEMA Type 10-30R):

Go to “3-Wire Power Supply Cord

Connection” on page 13.

13

1. Remove center screw

Remove center terminal block screw (B).

3. Connect remaining wires

2. Connect neutral wire

Connect remaining wires under outer terminal block screws.

Tighten screws. Finally, reinsert tab of terminal block cover into

slot of dryer rear panel. Secure cover with hold-down screw. Now

go to “Venting Requirements.”

Connect neutral wire (white or center) (C) of power supply cord

under center terminal block screw (B). Tighten screw.

3-wire receptacle

(NEMA type 10-30R)

3 prong plug

Spade terminals

with upturned ends

Ring terminals

4. Connect remaining wires

Connect remaining wires under outer terminal block screws.

Tighten screws. Finally, reinsert tab of terminal block cover into

slot of dryer rear panel. Secure cover with hold-down screw. Now

go to “Venting Requirements.”

3-Wire Power Supply Cord Connection

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

14

Direct Wire Connection

2. Attach direct wire cable to strain relief

Put direct wire cable through the strain relief. The strain relief

should have a tight fit with the dryer cabinet and be in a horizontal

position. Tighten strain relief screw against the direct wire cable.

3-wire direct connection:

Go to “3-Wire Direct Wire Connection”

on page 15.

4-wire direct connection:

Go to “4-Wire Direct Wire Connection”

on this page.

If your wiring looks like this:

4-Wire Direct Wire Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit 3-wire connections.

1. Prepare your 4-wire cable

for direct connection

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer

may be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable, leaving

bare ground wire at 5" (127 mm). Cut 1

1

/2" (38 mm) from remaining

three wires. Strip insulation back 1" (25 mm). Shape ends of wires

into hooks.

For direct wire installations:

1. Attach direct wire strain relief

Unscrew the removable conduit connector (A) and any screws

from a 3/4" (19 mm) UL Listed strain relief. Put the threaded

section of the strain relief (C) through the hole below the terminal

block opening (B). Reaching inside the terminal block opening,

screw the removable conduit connector (A) onto the strain relief

threads and tighten securely.

Direct wire strain relief

15

2. Prepare to connect neutral ground

wire and neutral wire

Remove center terminal block screw (B). Remove neutral ground

wire (E) from green external ground conductor screw (A).

2. Remove center screw

Remove center terminal block screw (B).

4. Connect ground wire

Connect ground wire (green or bare) (F) of direct wire cable under

green external ground conductor screw (A). Tighten screw.

5. Connect remaining wires

Place hooked ends of remaining direct wire cable wires under

outer terminal block screws (hooks facing right). Squeeze

hooked ends together and tighten screws. Finally, reinsert tab of

terminal block cover into slot of dryer rear panel. Secure

cover

with hold-down screw. Now go to “Venting Requirements.”

1. Prepare your 3-wire cable

for direct connection

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer

may be moved if needed.

Strip 3

1

/2" (89 mm) of outer covering from end of cable. Strip

insulation back 1" (25 mm). If using 3-wire cable with ground

wire, cut bare wire even with outer covering. Shape wire ends

into hooks.

3. Connect neutral ground wire

and neutral wire

Connect neutral ground wire (E) and place

hooked end (hook facing right) of neutral wire

(white or center wire) (C) of direct wire cable

under center screw of terminal block (B). Squeeze

hooked ends together and tighten screw.

3-Wire Direct Wire Connection

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

16

Optional External Ground for 3-Wire

Connection (Power Supply Cord Shown)

IMPORTANT: You must verify with a qualified electrician that this

grounding method is acceptable before connecting.

1. Prepare to connect neutral ground

wire and neutral wire

Install the correct strain relief for your electrical connection

method, as shown on page 12 or 14.

Remove center terminal block screw (B). Remove neutral ground

wire (E) from green external ground conductor screw (A).

Connect a separate copper ground wire (G) under the green

external ground conductor screw (A) to an adequate ground.

Finally, reinsert tab of terminal block cover into slot of dryer rear

panel. Secure cover with hold-down screw. Now go to “Venting

Requirements.”

4. Connect external ground wire

Connect neutral ground wire (E) and neutral wire (white or center

wire) (C) of power supply cord or cable under center terminal

block screw (B). Tighten screw.

2. Connect neutral ground wire

and neutral wire

Place ends of remaining wires under outer terminal block screws.

Tighten screws.

3. Connect remaining wires

Place hooked ends of remaining direct wire cable wires under

outer terminal block screws (hooks facing right). Squeeze

hooked ends together and tighten screws. Finally, reinsert tab of

terminal block cover into slot of dryer rear panel. Secure cover

with hold-down screw. Now go to “Venting Requirements.”

4. Connect remaining wires

3. Connect neutral wire

Place hooked end of neutral wire (white or

center) (C) of direct wire cable under center

terminal block screw (B), hook facing right.

Squeeze hooked end together. Tighten screw.

17

1. Connect gas supply to dryer

Remove red cap from gas pipe. Using a wrench to tighten,

connect gas supply to dryer. Use pipe-joint compound

on threads of all non-flared male fittings. If flexible metal

tubing is used, be sure there are no kinks.

NOTE: For propane gas connections, you must use

pipe-joint compound resistant to action of propane gas.

Do not use TEFLON

®

tape.

2. Plan pipe fitting connection (Option 1)

A combination of pipe fittings must be used to connect dryer to

existing gas line. A recommended connection is shown. Your

connection may be different, according to supply line type, size,

and location.

3. Open shut-off valve

Open shut-off valve in supply line; valve is open when handle is

parallel to gas pipe. Then, test all connections by brushing on

an approved noncorrosive leak-detection solution. Bubbles will

show a leak. Correct any leak found.

MAKE GAS CONNECTION

(Gas models only)

A. Flared male fitting

B. Non-flared male fitting

A. 3/8" flexible gas connector

B. 3/8" dryer gas pipe

C. 3/8" to 3/8" pipe elbow

D. 3/8" pipe-to-flare adapter

fitting

A. Closed valve

B. Open valve

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

18

Louvered Hood

Angled Hood

Box Hood

Recommended Styles:

Acceptable Style:

Venting Requirements

VENTING

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or flexible metal vent shall be used for

exhausting.

4" (102 mm) heavy metal exhaust vent

Exhaust hoods:

■

An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

■

Must be at least 12" (305 mm) from ground or any object

that may obstruct exhaust (such as owers, rocks, bushes,

or snow).

■

Do not use an exhaust hood with a magnetic latch.

■

Only a 4" (102 mm) heavy metal exhaust vent and clamps may

be used.

■

Do not use plastic or metal foil vent.

Rigid metal vent:

■

Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■

Must be fully extended and supported in nal dryer location.

■

Remove excess to avoid sagging and kinking that may result

in reduced airow and poor performance.

■

Do not install in enclosed walls, ceilings, or oors.

■

The total length should not exceed 7¾ ft. (2.4 m).

■

The length of exible metal vent used must be included in

the overall vent system design as shown in the “Vent System

Charts.”

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not plugged

with lint. Replace plastic or metal foil vents with rigid metal

or exible metal vents. Review “Vent System Charts” and, if

necessary, modify existing vent system to achieve best drying

performance.

Elbows:

45° elbows provide better airow than 90° elbows.

Clamps:

■

Use clamps to seal all joints.

■

Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and

catch lint. Do not use duct tape.

Better

Good

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

19

Plan Vent System

Recommended exhaust installation:

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible

metal vent

G. Vent length necessary

to connect elbows

H. Exhaust outlet

Optional exhaust installations:

This dryer can be converted to exhaust out the right side,

left side (all models except long vent), or through the bottom.

If you prefer, you may contact your local dealer to have the

dryer converted.

A. Standard rear offset exhaust installation

B. Left- or right-side exhaust installation

C. Bottom exhaust installation

Special provisions for mobile homes:

Exhaust vent must be securely fastened to a noncombustible

portion of mobile home and must not terminate beneath the

mobile home. Terminate exhaust vent outside.

Determine vent path:

■

Select route that will provide straightest and most direct path

outdoors.

■

Plan installation to use fewest number of elbows and turns.

■

When using elbows or making turns, allow as much room as

possible.

■

Bend vent gradually to avoid kinking.

■

Use as few 90° turns as possible.

Determine vent length and elbows needed for best

drying performance:

■

Use the following “Vent System Charts” to determine type of

vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specied in

“Vent System Charts.”

Exhaust systems longer than those specied will:

■

Shorten life of dryer.

■

Reduce performance, resulting in longer drying times and

increased energy usage.

The “Vent System Charts” provide venting requirements that will

help achieve best drying performance.

Standard Vent System Chart

Number of 90°

elbows

Type of vent Angled hoods

0

Rigid metal 64 ft. (20 m)

1

Rigid metal 54 ft. (16.5 m)

2

Rigid metal 44 ft. (13.4 m)

3

Rigid metal 35 ft. (10.7 m)

4

Rigid metal 27 ft. (8.2 m)

WARNING

Fire Hazard

Cover unused exhaust holes with a manufacturer’s

exhaust cover kit.

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

G

20

Long Vent System Chart

Number of 90°

elbows

Type of vent Angled hoods

0

Rigid metal 160 ft. (48.8 m)

1

Rigid metal 150 ft. (45.7 m)

2

Rigid metal 140 ft. (42.7 m)

3

Rigid metal 130 ft. (39.6 m)

4

Rigid metal 120 ft. (36.6 m)

Install Vent System

1. Install exhaust hood

2. Connect vent to exhaust hood

Install exhaust hood and use caulking compound to seal exterior

wall opening around exhaust hood.

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location using

straightest path possible. Avoid 90° turns. Use clamps to seal all

joints. Do not use duct tape, screws, or other fastening devices

that extend into interior of vent to secure vent, because they can

catch lint.

To determine if your model has a long vent system, refer to

the type code located on the serial number plate in the inner

door well. Example: An electric model would be DJAV – ELE –

XXXXXXX-XXX. A gas model would be DJAV – NAT – XXXXXXX-

XXX.

NOTE: For long vent systems, use of box/louvered hoods will

improve venting regardless of length.

La page est en cours de chargement...

Maytag MED5630HW Guide d'installation

Ce manuel convient également à

Maytag MED5630HW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents