Keurig B40 Manuel utilisateur

Marque: Keurig

Modèle: B40

Catégorie: Cafetières

Taper: Manuel utilisateur

Ce manuel convient également à

Coffeemaker B40

WARNING

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT REMOVE

THE BOTTOM COVER. NO USER

SERVICEABLE PARTS ARE INSIDE. REPAIR

SHOULD BE DONE BY AUTHORIZED

SERVICE PERSONNEL ONLY.

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

KEURIG

GOURMET SINGLE CUP

HOME BREWING SYSTEM

Elite - Model B40 Use & Care Guide

TABLE OF CONTENTS

SECTION 1

SET-UP & OPERATION

Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Set-Up & First Brew . . . . . . . . . . . . . . . . . . 6

SECTION 2

CONTROLS & INDICATORS

LED Control Center . . . . . . . . . . . . . . . . . . . 8

SECTION 3

CLEANING & MAINTENANCE

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

De-Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

SECTION 4

TROUBLESHOOTING . . . . . . . . . . . . . . . . . 11

SECTION 5

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Pour des directives en Français,

veuillez vous reporter à la page 13.

CAUTION: There are two sharp needles that

puncture the K-Cup

portion pack, one

above the K-Cup Holder and the other in the

bottom of the K-Cup Holder.

o avoid risk of injury, do not put your

fingers in the K-Cup Chamber.

CAUTION: There is extremely hot water in

the K-Cup Holder during the brew process.

o avoid risk of injury, do not lift the Handle

or open the K-Cup Chamber during the

brew process.

SHORT CORD INSTRUCTIONS: A short power

supply cord is provided to reduce the risk of

becoming entangled in or tripping over a longer

cord.

If an extension cord is used, (1) the marked

electrical rating of the cord set or extension cord

should be at least as great as the electrical rating of

the appliance, (2) the cord should be arranged so

that it will not drape over the countertop or table-

top where it can be pulled on by children or tripped

over unintentionally and (3) the extension cord

must include a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

Record your Brewer Serial Number here.

The Serial Number is located on the

bottom of the Brewer on a white sticker.

_________________________________

Features

Water Reservoir Lid

Water Reservoir

Water Reservoir Lock Tab Slots

Handle

K-Cup

Portion Pack Holder (E and F are

the K-Cup Holder Assembly)

Funnel

Lid

K-Cup

Portion Pack Assembly Housing

Housing

Drip Tray Plate

Drip Tray

Drip Tray Base

Vent

Power Cord

Brew Button

Brew Light (Green)

Power Button

Power Light (Green)

Auto Off Button

Auto Off Light (Green)

Heating Light (Red)

De-Scale Light (Red)

Add Water Light (Blue)

Elite - Model B40 Brewer

Controls and Indicators

1. Keep your Brewer turned ‘ON’ at all times.

To brew a fresh cup of coffee or tea anytime

you want, we suggest you keep your Brewer

turned ‘ON’ all the time.

However, you can set the Brewer to automati-

cally turn off two hours after your last brew.

Follow the simple instructions on page 8

to make using the Brewer convenient for you.

2. For the best tasting gourmet coffee or tea,

Keurig recommends using bottled or filtered

water.

Water quality varies from place to place. If you

notice an undesirable taste in your cup of coffee

such as chlorine or other mineral taste, we

recommend you consider using bottled water or

water from a filtration system.

3. Plug Brewer into its own grounded outlet.

If the electric circuit is overloaded with

other appliances, your Brewer may not

function properly. The Brewer should be

operated on its own circuit, separate from

other appliances.

4. Brewing into a travel mug.

To brew into a travel mug, simply remove the

Drip Tray Assembly and place the travel mug

on the Drip Tray Base.

1. Place Brewer box on a large steady surface

(such as a table or countertop) or

on the floor. Open the box.

2. Remove the Quick Start Guide, Use & Care

Guide and other literature.

3. Remove the package of complimentary

K-Cup

portion packs.

4. Turn the box on its side with front of box

face down.

5. Reach into the box and grasp the plastic

bag that contains the Brewer.

6. Carefully pull the plastic bag (and

packaging materials) toward you and out

of the box. The Brewer will still be encased

in the polyfoam and be on its side.

7. Remove the top polyfoam packaging

material.

8. Carefully lift Brewer off of the bottom

polyfoam and place it upright on a flat,

steady surface.

9. Lift plastic bag off of Brewer.

10. Carefully turn the Brewer on its side and

record on page 3 of this book the Serial

Number located on the white sticker on the

bottom of the Brewer. The Serial Number

is also located on the bottom of the Brewer

box.

11. Place the Brewer upright on a flat,

steady surface. Remove tape holding

Water Reservoir in place.

We recommend you save all packing materials

in case future shipping of the product is

necessary.

SET-UP & OPERATION

Helpful Hints

SECTION 1

WARNING: Keep all plastic bags away

from children.

Unpacking Instructions

Set-Up & First Brew

IMPORTANT: You cannot use your Keurig

brewer until it has been primed for its first use

as set forth below.

Priming your Brewer

1. Unwrap cord and plug the brewer into a

grounded outlet.

2. Place a cup or mug on the Drip Tray Plate.

3. Remove the Water Reservoir from Brewer by

first removing Lid from Reservoir, then lifting

Reservoir straight up and away from Brewer

(may be tight). Rinse with fresh water.

4. Fill Water Reservoir with fresh water so

that the water level reaches the line just

below the top edge of the clear viewing

area. (Be careful not to over fill.)

5. Place Water Reservoir base into the left

side of the Brewer and be sure the

Water Reservoir Lock Tabs engage

with the Brewer. Replace Lid on Water

Reservoir.

6. Press Power Button found on upper right

panel of the Brewer. The green light next to

the Power Button will become illuminated.

7. The red light next to 'DE-SCALE' on the

LED Control Center will flash to indicate the

Brewer needs to be primed. Make sure

the handle is all the way down before

continuing. Please note, a K-Cup should not

be used for the Priming Sequence.

8. Press the Brew Button below the flashing

green light.

9. The Brewer will automatically fill with water

(priming it) and then the water will be

heated. This will take about 3 minutes. During

the heating period the red light next to 'HEAT-

ING' on the LED Control Center will become

illuminated. Once the water is heated, the red

light will turn off and the green light above the

Brew Button will flash.

10.Press the Brew Button below the flashing

green light to start a cleansing brew, during

which hot water will flow into your cup or

mug. Pour the hot water into the sink.

11.The Brewer may take 15 seconds to reheat

water between brews during which time the

red light next to 'HEATING' on the LED

Control Center may be illuminated. When the

water has heated, the red light will turn off.

12. The one-time priming process is now

complete and you are ready to brew!

Ready to Brew your First Cup

1. The green light next to the Power Button on

the LED Control Center will be illuminated

to indicate the Brewer is powered on.

2. Place a cup or mug on the Drip Tray Plate.

3. Lift the Handle and the K-Cup Holder will

open toward you.

4. Select a K-Cup

portion pack.

5. Place a K-Cup

portion pack in the K-Cup

Holder (as shown in exhibit at top of page).

6. Lower the Handle completely to close the

Lid.

7. Press the Brew Button below the flashing

green light on the LED Control Center. This

will yield a 7.25 oz serving.

8. The green light above the Brew Button on

the LED Control Center will remain lit while

brewing.

9. There may be a short pause before the

brewing process begins. The process lasts

for approximately 40 seconds and ends

with a burst of air to remove all liquid

coffee or tea from the K-Cup.

10. Lift the Handle to remove and dispose of

the used K-Cup. CAUTION: K-Cup will be hot.

11. Enjoy your first cup of Keurig Brewed

gourmet coffee or tea!

12. The red light next to 'HEATING' on the

LED Control Center may be lit as the

water is heated for the next brew cycle.

The Brewer will be ready for use in

approximately 15 seconds.

Stopping the Brew Process

If you need to stop the brewing after the

process has started, press the Power Button

to turn the Brewer ‘OFF’. The flow of coffee

or tea will stop, the heating element will shut

off and the green light next to the Power

Button will disappear.

NOTE: You may see small amounts of water

coming from the Vent and dripping into the

Water Reservoir during this and subsequent

heating – this is normal.

NOTE: Do not remove the foil lid or

puncture the K-Cup

portion pack.

NOTE: If the Water Reservoir is empty or not

in place on the Brewer, then the blue light

next to 'ADD WATER' on the LED Control

Center will be illuminated. The Brew Button

will not be activated until water is added to

the Water Reservoir.

CAUTION: There are two sharp needles that

puncture the K-Cup

portion pack, one above

the K-Cup Holder and the other in the bottom

of the K-Cup Holder. T

o avoid risk of injury,

do not put your fingers in the K-Cup Chamber

NOTE: If you do not push the Brew Button in

60 seconds, the Brew Button will be disabled

to prevent accidental activation. Re-activate

the Brew Button by raising and lowering the

Handle completely.

CAUTION: There is extremely hot water in

the K-Cup Holder during the brew process.

o avoid risk of injury, do not lift the

Handle or open the K-Cup Chamber

during the brew process.

Handle

K-Cup

Chamber

NOTE: If Brewer has been exposed to tempera-

tures below freezing, allow Brewer at least two

hours to reach room temperature before prim-

ing. A frozen or extremely cold brewer will not

prime properly and can cause damage.

NOTE: Following the brew, your Brewer will

fill in preparation for the next brew. The pump

will make a vibrating sound. This is normal.

K-Cup

portion pack

NOTE: You may get less coffee or tea in your

cup during your next brew. We recommend

that you perform a cleansing brew with water

only after a terminated brew. Then your NEXT

brew will be the proper volume.

Adding Water

The LED Control Center of your Brewer will

indicate when the water level in the tank is low

or if the Water Reservoir has been removed by

illuminating the blue light next to ‘ADD WATER’.

The Brewer will not allow you to brew when

the blue 'ADD WATER' light is illuminated.

The Water Reservoir can be filled in two ways.

1. Lift off the Water Reservoir Lid and pour

water directly into the Water Reservoir

while it is still attached to the Brewer, then

replace the Lid.

2. Remove the Water Reservoir from Brewer

by first removing Lid from Reservoir, then

lifting Reservoir straight up and away from

Brewer. Fill with water. Place the Water

Reservoir back on the Brewer and replace

the Lid.

Brewing Hot Water

Your Brewer is able to produce a cup of hot

water for making hot chocolate, for use in

cooking, for making soups, etc. Simply raise

and lower the handle on the Brewer without

adding a K-Cup

portion pack. The green light

above the Brew Button on the LED Control

Center will flash. Be sure to have a mug or cup

on the Drip Tray and then press the Brew Button.

Purging the Brewer

If your Brewer has not been used for more

than one week, you should purge the water

from the inner tank.

1. If there is water in the Water Reservoir,

remove the Lid, then lift Reservoir straight up

and away from Brewer. Discard water, rinse

and refill with water. Place the Water Reservoir

back on the Brewer and replace the Lid. (If

there is no water in Reservoir, simply refill.)

2. Be sure the Brewer is turned on. Raise and

lower the handle on the Brewer without

inserting a K-Cup and wait until the red light

next to 'HEATING' turns off.

3. The green light above the Brew Button on

the LED Control Center will flash. Be sure to

have a mug or cup on the Drip Tray and then

press the Brew Button.

4. Repeat steps 2 and 3 two more times to

completely purge water from inner tank.

If you are experiencing any problems with

your Brewer, please contact Customer

Service at 1-866-901-BREW (2739).

SECTION 2

CONTROLS & INDICATORS

LED Control Center

Programming Auto off Timer Feature

Set the Brewer to turn off two hours after the

last brew.

a. Press the Power Button to turn on the Brewer.

b. Press the black button above the Power

Button on the LED Control Center to turn on

the Auto Off Timer feature. The green light

next to 'AUTO OFF' will become illuminated.

When the Auto Off Timer is enabled, your

Brewer will automatically turn off two hours

after your last brew.

c. To turn off

the Auto Off

Timer, sim-

ply press the

black button

again and

the green

light next to

'AUTO OFF'

will turn off.

IMPORTANT: Do not remove the Water

Reservoir during the brewing process.

Cleaning External Parts

Regular cleaning of the Brewer’s external com-

ponents is recommended.

1. Never immerse the base unit in water or

other liquids. The Housing and other external

components may be cleaned with a soapy,

damp, non-abrasive cloth.

2. The Drip Tray can accumulate up to 8

ounces of overflow. The Drip Tray and Drip

Tray Plate should be periodically inspected and

rinsed clean. To remove the Drip Tray

Assembly, simply slide it toward you, keeping it

level at all times to avoid spilling. The Drip Tray

and Drip Tray Plate are dishwasher safe.

Cleaning the K-Cup

Portion Pack

Holder Assembly

1. Cleaning the Parts

The K-Cup Holder Assembly is dishwasher safe.

To remove from the Brewer, open the cover by

lifting the Handle. Grasp the top of the K-Cup

Holder with one hand while pushing up on the

bottom of the K-Cup Holder from underneath

with the other until it releases. After cleaning,

align the K-Cup Holder with the opening using

the two front ribs as a guide and snap into

place from the top.

2. Cleaning the Funnel

The Funnel can be removed from the K-Cup

Holder by pulling on it until it snaps off. The

Funnel is dishwasher safe. To replace it just snap

it back onto the K-Cup Holder Assembly.

3. Cleaning the Exit Needle

The Exit Needle is located on the inside bottom

of the K-Cup Holder Assembly. Should a clog

arise due to coffee grinds, it can be cleaned

using a paper clip or similar tool. Remove K-

Cup Holder, insert the paper clip into the

Needle to loosen the clog and push it out. The

K-Cup Holder is dishwasher safe.

Cleaning the Water Reservoir and

Water Reservoir Lid

The Water Reservoir Lid should be cleaned

with a damp soapy non-abrasive cloth. Lid

should not be put into the dishwasher.

The Water Reservoir can be placed into the

dishwasher for cleaning or can be cleaned with

soapy water and rinsed thoroughly.

Do not dry the inside of the Water Reservoir

with a cloth as lint may remain.

De-Scaling Your Brewer

Mineral content in water varies from place to

place. Depending on the mineral content of the

water in your area, calcium deposits or scale

may build up in your Brewer. Scale is non-

toxic, but left unattended, it can hinder Brewer

performance. De-scaling your Brewer helps

maintain the heating element, and other inter-

nal parts of the Brewer that come in

contact with water.

The Brewer should be de-scaled every 6

months to ensure optimal performance. It is

SECTION 3

CLEANING & MAINTENANCE

CAUTION: There are sharp needles that

puncture the K-Cup above the K-Cup Holder

and in the bottom of the K-Cup Holder. T

avoid risk of injury, do not put your fingers

in the K-Cup Chamber.

K-Cup Holder

Assembly

K-Cup Holder

Funnel

CAUTION: Please rinse the Water Reservoir

thoroughly after cleaning to ensure that no

cleaners or cleaning solutions remain in

this area as they may contaminate the

water supply in the Brewer.

possible for calcium deposits to build up faster,

making it necessary to de-scale more often.

This Brewer is equipped with sensors to detect

when scale buildup is interfering with the

performance of the Brewer. When this is

detected, the red light next to 'DE-SCALE' will

be illuminated.

You should promptly de-scale using the proce-

dures outlined below once the 'DE-SCALE' light

illuminates on the LED Control Center.

De-Scaling

a. PREPARE

Step 1: Make sure you have at least 48

ounces of undiluted white vinegar on hand.

You will also need an empty sink and a

ceramic cup (do not use a paper cup.)

Step 2: Empty the water in the Water

Reservoir.

b. FILL AND CLEAN

Step 1: Pour the vinegar into the Water

Reservoir and fill it to the line just below the

top edge of the clear viewing area.

Step 2: Place a ceramic cup in the Drip Tray

and run a brew cycle. DO NOT USE A K-CUP

portion pack just press the Brew Button.

Pour the contents of the cup into the sink.

Step 3: Repeat the brew process until the

Water Reservoir is empty, pouring the

contents of the cup into the sink after each

cycle. Remember to open and close the lid

between each cycle so the green Brew light

will flash.

Step 4: Rinse the Water Reservoir thoroughly

and fill with fresh water.

Step 5: Now let the Brewer stand for 4

hours while still on.

c. RINSE

Step 1: Ensure the Water Reservoir is filled

with fresh water.

Step 2: Place a ceramic cup on the Drip Tray

and run a regular brew cycle without using a

K-Cup. Pour the contents of the cup into the

sink.

Step 3: Repeat brew process until the Water

Reservoir is empty.

Step 4: You may need to perform additional

rinse cycles if you notice any residual taste.

Storage

Empty the Water Reservoir before storing and

take care to ensure that you store your Brewer

in a safe and frost free environment. Please be

sure to store your Brewer in its upright position

to avoid water leakage from the inner tank. If you

store the Brewer in a cold environment, you run

the risk of water freezing inside the Brewer and

causing damage. When you prepare to use it

after storage, we recommend rinsing the Water

Reservoir with fresh water and running three

cleansing brews without a K-Cup.

If you plan to move your Brewer to a different

location, turn the Brewer off, unplug it and

empty the Water Reservoir. If your Brewer has

been in an environment below freezing, please

be sure to let it warm to room temperature for

2 hours before using.

NOTE: If the red 'DE-SCALE' light is still

illuminated on the LED Control Center after

completing the procedure, repeat the de-

scaling procedure above.

NOTE: The Brewer will continue to function even

when the red 'DE-SCALE' light is illuminated.

However, if you do not de-scale soon after it is

displayed, continued scale build-up could

damage the Brewer. If this occurs, the red light

next to 'DE-SCALE will begin to blink to alert you

to the potential damage to the Brewer if you do

not de-scale immediately.

SECTION 4

TROUBLESHOOTING

SITUATION SOLUTION

Brewer will not brew

when used for the

first time

• Plug Brewer into an independent outlet.

• Check to be sure that it is plugged in securely.

• Plug into a different outlet.

• Reset circuit breaker if necessary.

• Make sure that the Power Button has been turned on and the power

light is illuminated.

• The Brewer must be primed for use by filling the internal hot water

tank before the first brew. The red light next to 'DE-SCALE' on the

LED Control Center will flash. (refer to page 6)

• If Brewer is cold/frozen, wait for two hours for it to reach room

temperature before powering on.

Brewer will not brew

• After placing the K-Cup

portion pack in the K-Cup Holder, make sure

that the Handle is pushed down securely and the green light above

the Brew Button on the LED Control Center is flashing.

• If the blue light next to 'ADD WATER' on the LED Control Center is

illuminated, add water to Water Reservoir or make sure the Water

Reservoir is seated properly in its base.

• If the blue light next to 'ADD WATER' on the LED Control Center con-

tinues to be on even after refilling, contact Customer Service at

1-866-901-BREW (2739).

Brewing a partial cup

• The Exit Needle may be clogged. (refer to page 9).

• Clean K-Cup Holder if necessary and rinse under faucet. (refer to page 9).

• The Water Reservoir may have been removed during brewing.

Replace the Water Reservoir and perform a cleansing brew.

• If the red 'DE-SCALE' light is illuminated, descale the Brewer (refer to

page 9).

• If you have repeated the descale procedure on your Brewer two times

and the light is still on, contact Customer Service at 1-866-901-BREW

(2739).

Brewer Does Not

Have Power

If any problems persist, contact Customer Service at 1-866-901-BREW (2739).

My brewer shuts off

automatically

• Check to make sure that the Auto Off Timer feature has not been set.

If the green light next to 'AUTO OFF' on the LED Control Center is illu-

minated, press the black button to turn off the Auto Off Timer feature.

WARRANTY

Limited One Year Warranty

Keurig warrants that your Brewer will be free

of defects in materials or workmanship under

normal home use for one year from the date

of purchase. It is recommended that you fill

out and return the warranty card enclosed

with your Brewer so that your purchase infor-

mation will be stored in our system. Keurig

will, at its option, repair or replace the Brewer

without charge upon its receipt of proof of

the date of purchase. If a replacement Brewer

is necessary to service this warranty, the

replacement Brewer may be new or recondi-

tioned. If a replacement Brewer is sent, a new

limited one year warranty will be applied to

the replacement Brewer.

This warranty only applies to Brewers

operated in the United States and Canada.

This warranty gives you specific legal rights,

and you may also have other rights that vary

from state to state and, in the case of Canada,

from Province to Province.

What is not covered by the

Limited Warranty?

THIS WARRANTY DOES NOT COVER CON-

SEQUENTIAL OR INCIDENTAL DAMAGES

SUCH AS PROPERTY DAMAGE AND DOES

NOT COVER INCIDENTAL COSTS AND

EXPENSES RESULTING FROM ANY BREACH

OF THIS WARRANTY, EVEN IF FORESEEABLE.

Some states or Provinces do not allow the

exclusion or limitations of incidental or con-

sequential damages, so the above limitation

or exclusion may not apply to you depending

on the state or Province of purchase.

Nor does this warranty cover damages

caused by services performed by anyone

other than Keurig or its authorized service

providers, use of parts other than genuine

Keurig parts, or external causes such as

abuse, misuse, inappropriate power supply

or acts of God.

Other Limitations

THIS WARRANTY IS EXCLUSIVE AND IS IN

LIEU OF ANY OTHER EXPRESS WARRANTY,

WHETHER WRITTEN OR ORAL. THE

DURATION OF ANY IMPLIED WARRANTIES,

INCLUDING BUT NOT LIMITED TO ANY

IMPLIED WARRANTIES OF MERCHANT -

ABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, IS EXPRESSLY LIMITED TO THE

PERIOD OF DURATION OF THIS

LIMITED WARRANTY. Some states or

Provinces do not allow limitations on how

long an implied warranty lasts, so the above

limitation may not apply to you depending on

the state or the Province of purchase.

How do you obtain warranty service?

Keurig Brewers are high quality

appliances and, with proper care, are

intended to provide years of satisfying

performance. However, should the need arise

for warranty servicing, simply call Keurig

Customer Service at our toll free phone

number 1-866-901-BREW (2739). Please

do not return your Brewer for servicing

without first speaking to Keurig Customer

Service to obtain an Authorization to Return

number (ATR). Keurig Brewers returned

without an ATR number will be returned to

the sender without servicing.

Keurig, Incorporated

101 Edgewater Drive

Wakefield, MA 01880

1-866-901-BREW (2739)

MANUEL D'UTILISATION ET D'ENTRETIEN

Lorsque vous utilisez des appareils électriques,

vous devriez suivre les mesures de sécurité de

base suivantes :

1. Veuillez lire toutes les instructions avant

l’utilisation.

2. Ne pas toucher les surfaces chaudes.

Utiliser les poignées.

3. L’utilisation d’un accessoire qui n’a pas été

testé avec cet appareil peut causer des

blessures.

4. Éviter le contact ou la proximité de

l’appareil avec un élément électrique ou un

brûleur à gaz. Éviter également de placer

l’appareil à l’intérieur d’un four chaud.

5. Ne pas utiliser à l’extérieur.

6. Pour éviter les risques de chocs

électriques, ne pas immerger la fiche, le

cordon d’alimentation ou l’appareil dans

l’eau ou dans tout autre liquide.

7. Ne pas trop remplir le réservoir d’eau.

8. N’utiliser que de l’eau dans cet appareil!

Ne verser aucun autre liquide ou aliment

dans le réservoir d’eau à l’exception des

produits mentionnés dans les directives

de nettoyage du présent manuel.

9. Débrancher la cafetière avant de la nettoyer

ou de la réparer. Laisser l’appareil refroidir

avant d’ajouter ou d’enlever des pièces et

avant de le nettoyer.

10. Pour une utilisation optimale, brancher

l’appareil dans une prise de courant séparée

sur un circuit spécialisé pour éviter que les

lumières vacillent, que les fusibles sautent

ou que les disjoncteurs se déclenchent.

11. Ne jamais utiliser un appareil dont la

fiche ou le cordon d’alimentation est

endommagé ou un appareil qui présente

un trouble de fonctionnement ou qui

a été endommagé.

12. Ne pas laisser le cordon d’alimentation

pendre d’une table ou d’un comptoir ni

entrer en contact avec une surface chaude.

13. Pour débrancher la cafetière, appuyer

sur le bouton de mise en marche situé

sur le dessus de la cafetière pour la mettre

en position ‘OFF’ et retirer le cordon

de la prise.

14. Ne jamais laisser des enfants utiliser

la cafetière ni rester à proximité sans

surveillance.

15. Ne pas soulever la poignée pour ouvrir le

couvercle de la cafetière durant l’infusion.

16. Toujours laisser le couvercle sur le

réservoir d’eau, sauf lors du remplissage.

17. L’appareil est équipé d’un cordon

d’alimentation muni d’un conducteur et

d’une prise de mise à la terre. L’appareil

doit être mis à la terre en utilisant une

prise de courant à contact de mise à la

terre à trois trous. En cas de court-circuit,

la mise à la terre réduit les risques de

chocs électriques.

18. Si la prise de courant est une prise de

courant murale standard à deux trous,

le propriétaire a l’obligation et la

responsabilité de la faire remplacer

par une prise de courant de mise à la

terre à trois trous.

19. Il ne faut en aucun cas couper ou enlever

la troisième broche (mis à la terre)

du cordon d’alimentation, ni utiliser

un adaptateur.

20. Consulter un électricien qualifié si les

instructions sur la mise à la terre ne sont

pas parfaitement comprises ou en cas de

doutes sur la mise à la terre de l’appareil.

21. Ne pas utiliser l’appareil pour une autre fin

que celle pour laquelle il a été conçu.

CONSERVER

CE MANUEL.

FONCTIONNEMENT ET UTILISATION SANS DANGER

RÈGLES DE SÉCURITÉ IMPORTANTES

SECTION 5

Keurig B40 Manuel utilisateur

Marque: Keurig

Modèle: B40

Catégorie: Cafetières

Taper: Manuel utilisateur

Ce manuel convient également à

Coffeemaker B40

Télécharger le PDF

rapport

dans d''autres langues

English: Keurig B40 User manual

Documents connexes

Autres documents

GMCW RC400 Manuel utilisateur