Keurig Elite B40 Le manuel du propriétaire

Marque: Keurig

Modèle: Elite B40

Catégorie: Cafetières

Taper: Le manuel du propriétaire

USING YOUR BREWER

OWNER’S MANUAL: Getting the most from your new

Platinum B70 Keurig

Brewer

USING YOUR BREWER

OWNER’S MANUAL: Getting the most from your new

Platinum B70 Keurig

Brewer

USING YOUR BREWER

OWNER’S MANUAL: Getting the most from your new

Elite B40 Keurig

Brewer

COMMENT UTILISER VOTRE CAFETIÈRE

MANUEL D’UTILISATION : Tirez le meilleur de

votre nouvelle cafetière Elite B40 de Keurig

IMPORTANT SAFEGUARDS Safe Operation & Use

When using electrical appliances, basic safety

precautions should be followed, including

the following:

1. Read all instructions before using.

2. Do not touch hot surfaces. Use handles and

knobs when available.

3. This appliance must be properly installed and

located in accordance with these instructions

before it is used.

4. The use of accessory attachments not recom-

mended by the appliance manufacturer may re-

sult in fire, electrical shock or injury to persons.

5. Do not place on or near a hot gas or electric

burner, or in a heated oven.

6. Do not use outdoors.

7. To protect against fire, electric shock and injury

do not immerse cords, plugs, or the appliance in

water or any other liquid.

8. Do not overfill the Water Reservoir with water.

9. Use only water in this appliance! Do not put any

other liquids or foods in the Water Reservoir

except as instructed in the Cleaning Instruc-

tions in this guide.

10. Turn off and unplug the Brewer before

cleaning or maintenance. Allow to cool

before putting on or taking off parts and

before cleaning the appliance.

11. For best operation, plug the appliance into its

own electrical outlet on a dedicated circuit to

prevent flickering of lights, blowing of fuses or

tripping a circuit breaker.

12. Do not operate any appliance with a damaged

cord or plug or after the appliance malfunc-

tions or is damaged in any manner. Contact

Keurig

Customer Service to report any

malfunction of or damage to the Brewer.

13. Do not let the cord hang over the edge of

the table or counter, or touch hot surfaces.

14. To disconnect, press the Power Button on

the top of the Brewer to ‘OFF’ status and then

remove the plug from the wall outlet.

15. Close supervision is necessary when any

appliance is used by or near children.

16. Do not lift the Handle to open the Lid of

the Brewer while brewing is in progress.

17. Always keep the Water Reservoir Lid on

the Water Reservoir unless you are refilling it.

18. This appliance is equipped with a power cord

having a grounding wire with a grounding plug.

The appliance must be grounded using a 3-

hole properly grounded outlet. In the event of

an electrical short circuit, grounding reduces

the risk of electrical shock.

19. If the outlet is a standard 2-prong wall outlet,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

20. Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord or use an adapter.

21. Consult a qualified electrician if the grounding

instructions are not completely understood, or

if doubt exists as to whether the appliance is

properly grounded.

22. Do not use the appliance for other than

its intended use.

SAVE THESE

INSTRUCTIONS.

TABLE OF CONTENTS

KEURIG

GOURMET SINGLE CUP HOME BREWING SYSTEM

Elite — Model B40

Using Your Brewer

SET-UP

Helpful Hints ........................................................................................4

Unpacking ............................................................................................4

Features ...............................................................................................5

SECTION 1 — PRIMING & FIRST BREW

Priming & First Brew .........................................................................6

SECTION 2 — CONTROLS & INDICATORS

Programming Auto Off Timer Feature ..........................................10

SECTION 3 — CLEANING & MAINTENANCE

Cleaning ..............................................................................................10

De-Scaling..........................................................................................11

Storage ...............................................................................................12

SECTION 4 — TROUBLESHOOTING..................................................13

SECTION 5 — WARRANTY ................................................................14

Pour des directives en français, veuillez vous reporter à la page 15.

Record your Brewer Serial Number here.

Removing the serial number label from the Brewer will void warranty.

CAUTION: There are two sharp needles that puncture the K-Cup

portion pack,

one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To

avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.

CAUTION: There is extremely hot water in the K-Cup Holder during the

brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup

Assembly Housing during the brewing process.

SHORT CORD INSTRUCTIONS: A short power supply cord is provided to

reduce the risk of becoming entangled in or tripping over a longer cord.

If an extension cord is used, (1) the marked electrical rating of the cord set

or extension cord should be at least as great as the electrical rating of the

appliance; (2) the cord should be arranged so that it will not drape over the

countertop or tabletop where it can be pulled on by children or tripped over un-

intentionally; and (3) the extension cord must include a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING

LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,

BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT REMOVE THE

BOTTOM COVER. NO USER SERVICEABLE

PARTS ARE INSIDE. REPAIR SHOULD BE DONE

BY AUTHORIZED SERVICE PERSONNEL ONLY.

RISK OF FIRE OR

ELECTRIC SHOCK

DO NOT OPEN

Set-up

Helpful Hints

1. Keep your Brewer turned ‘ON’ at all times.

To brew a fresh cup of coffee, tea or hot cocoa

anytime you want, we suggest you keep your

Brewer turned ‘ON’ all the time. However, you

can set the Brewer to automatically turn off two

hours after your last brew. Follow the simple

instructions on page 10 to make using the

Brewer convenient for you.

2. For the best tasting gourmet coffee, tea or

hot cocoa Keurig

recommends using bottled

or filtered water.

Water quality varies from place to place. If you

notice an undesirable taste in your cup of coffee

such as chlorine or other mineral taste, we

recommend you consider using bottled water

or water from a filtration system.

3. Customize the Size, Flavor & Brew That’s

Perfect for You.

With the choice of over 200 varieties of K-Cups

and 2 brew sizes (Small Mug-7.25 oz. and Large

Mug-9.25 oz.) your Keurig Brewer gives you

endless options to customize the size, flavor

and brew that’s perfect for you. For a strong,

intense cup, select an Extra Bold K-Cup (with

up to 30% more ground coffee than regular

varieties) and brew size that’s right for you.

The smaller the brew size, the more intense

flavor in your cup. The larger the brew size,

the less intense flavor in your cup.

4. Plug Brewer into its own grounded outlet.

If the electric circuit is overloaded with other

appliances, your Brewer may not function

properly. The Brewer should be operated on

its own circuit, separate from other appliances.

5. Brewing into a travel mug.

To brew into a travel mug, simply remove the

Drip Tray Assembly and place the travel mug

on the Drip Tray Base.

6. De-scale Brewer regularly.

Please see page 12 for instructions.

Unpacking Instructions

1. Place Brewer box on a large steady surface

(such as a table or countertop) or on the floor.

Open the box.

2. Remove enclosed literature.

3. Turn the box on its side with front of box face

down.

4. Reach into the box and grasp the plastic

bag that contains the Brewer.

5. Carefully pull the plastic bag (and packaging

materials) toward you and out of the box. The

Brewer will still be encased in the polyfoam

and be on its side.

6. Remove the top polyfoam packaging material.

7. Carefully lift Brewer off of the bottom polyfoam

and place it upright on a flat, steady surface.

8. Lift plastic bag off of Brewer.

9. Record the serial number for this Brewer

on page 3 of this Guide. The serial number can

be found on the bottom of this box or on the

Brewer, behind the Drip Tray Assembly

(when removed).

10. Place the Brewer upright on a flat, steady

surface. Remove tape holding Water Reservoir

in place.

We recommend you save all packing materials in

case future shipping of the product is necessary.

WARNING:

Keep all plastic bags away

from children.

Features Elite — Model B40 Brewer

A. Water Reservoir Lid

B. Water Reservoir

C. Water Reservoir

Lock Tab Slots

D. Handle

E. Funnel

F. K-Cup

Portion Pack

Holder (E and F are the

K-Cup Holder Assembly)

G. Lid

H. K-Cup Portion

Pack Assembly

Housing

I. Housing

J. Drip Tray Plate

K. Drip Tray

L. Drip Tray Base

M. Vent

N. Power Cord

O. Small Mug Button

P. Large Mug Button

Q. Power Button

R. Power Light (Green)

S. Auto Off Button

T. Auto Off Light (Green)

U. Heating Light (Red)

V. De-Scale Light (Red)

W. Add Water Light (Blue)

B40 Brewer Controls and Indicators

!$ $ 7!4% 2

$%  3#! , %

(%!4 ) .'

!54/ /& &

0/ 7%2

SECTION 1 Priming & First Brew

Priming Your Brewer

1. Unwrap cord and plug the Brewer into a

grounded outlet. Remove all pieces of

packing tape.

2. Place a Large Mug (10 oz. minimum) on

the Drip Tray Plate.

3. Remove the Water Reservoir from Brewer by

first removing Lid from Reservoir (fig. 1), then

lifting Reservoir straight up and away from

Brewer (may be tight). Rinse with fresh water.

4. Fill Water Reservoir with bottled or filtered

water so that the water level reaches the line

just below the top edge of the clear viewing

area. (Be careful not to over fill.)

IMPORTANT: You cannot use your Keurig

Brewer until

it has been primed for its ﬁrst use as set forth below.

NOTE: If Brewer has been exposed to temperatures

below freezing, allow Brewer at least two hours to

reach room temperature before priming. A frozen

or extremely cold Brewer will not prime.

5. Place Water Reservoir base into the left side

of the Brewer and be sure the Water Reser-

voir Lock Tabs engage with the Brewer (fig. 2).

Replace Lid on Water Reservoir.

6. Press Power Button found on upper right panel

of the Brewer. The green light next to the Power

Button will become illuminated.

7. The red light next to ‘DE-SCALE’ on the LED

Control Center will flash to indicate the Brewer

needs to be primed. Make sure the Handle is all

the way down before continuing. NOTE: A K-Cup

should not be used for the Priming Sequence.

8. Press the flashing Small Mug Button. (fig. 3)

NOTE: If the Water Reservoir is empty or

not in place on the Brewer, the blue light next

to ‘ADD WATER’ on the LED Control Center will

be illuminated. The Small Mug Button will

not be activated until water is added to the

Water Reservoir.

9. The Brewer will automatically fill with water

(priming it) and then the water will be heated.

This will take about 3 minutes. During the heat

ing period the red light next to ‘HEATING’ on the

LED Control Center will become illuminated.

Once the water is heated, the red light will turn

off and the Small Mug Button will flash.

NOTE: Do not lift the Brewer Handle while priming.

ﬁg.

!$ $ 7!4 %2

$%  3# ! ,%

(%!4 ).'

!54// & &

0/ 7%2

ﬁg.

Small Mug

Ready to Brew Your First Cup

1. The green light next to the Power Button on

the LED Control Center will be illuminated to

indicate the Brewer is powered on.

2. Place a cup or mug on the Drip Tray Plate.

3. Lift the Handle and the K-Cup Holder

will open toward you. (fig. 4)

4. Select a K-Cup

portion pack.

NOTE: Do not remove the foil

lid or puncture the K-Cup.

5. Place a K-Cup portion pack

in the K-Cup Holder. (fig 5.)

CAUTION: There are two sharp needles that

puncture the K-Cup, one above the K-Cup Holder

and the other in the bottom of the K-Cup Holder

NOTE: You may see small amounts of water coming from the Vent and dripping

into the Water Reservoir during this and subsequent heating – this is normal.

10. Press the Small Mug Button to start a cleansing brew. Pour the hot water

into the sink.

11. The Brewer may take 15 seconds to reheat water between brews during

which time the red light next to ‘HEATING’ on the LED Control Center may

be illuminated. When the water has heated, the red light will turn off.

12. The one-time priming process is now complete and you are ready to brew!

To avoid risk of injury, do not put your

fingers in the K-Cup Holder.

6. Lower the Handle completely to close the Lid.

7. Select your brew size: The Small Mug choice

will yield a 7.25 oz. serving and the Large Mug

will yield a 9.25 oz. serving.

NOTE: If you do not push a Brew Button in 60

seconds, the Brew Buttons will be disabled to

prevent accidental activation. Re-activate the

Brew Buttons by raising and lowering the

Handle completely.

8. The blue light behind the Brew Button you

choose on the LED Control Center will remain

lit while brewing.

CAUTION: There is extremely hot water in the

K-Cup Holder during the brew process. To avoid

risk of injury, do not lift the Handle or open the

K-Cup Assembly Housing during the brew process.

9. There may be a short pause before the brewing

process begins. The entire brew process lasts

for approximately 1 minute and ends with a

burst of air to remove all liquid from the K-Cup.

10. Lift the Handle, remove and dispose of the

used K-Cup. CAUTION: K-Cup will be hot.

11. Enjoy your first cup of Keurig Brewed

gourmet coffee, tea or hot cocoa!

ﬁg.

Small Mug

(7.25 oz.)

Large Mug

(9.25 oz.)

Brewing Your First Cup (Continued)

SECTION 1 First Brew

Adding Water

The LED Control Center of your Brewer will

indicate when the water level in the Water

Reservoir is low or if the Water Reservoir has

been removed by illuminating the blue light

next to ‘ADD WATER’ (fig. 6). The Brewer will

not allow you to brew when the blue ‘ADD

WATER’ light is illuminated.

The Water Reservoir can be filled in two ways.

1. Lift off the Water Reservoir Lid and pour

water directly into the Water Reservoir

while it is still attached to the Brewer,

then replace the Lid.

2. Remove the Water Reservoir from Brewer by

first removing Lid from the Water Reservoir,

then lifting the Water Reservoir straight up

and away from Brewer. Fill with water. Place

the Water Reservoir back on the Brewer and

replace the Lid.

IMPORTANT: Do not remove the Water

Reservoir during the brewing process.

12. The red light next to ‘HEATING’ on the LED Control Center may be lit as

the water is heated for the next brew cycle. The Brewer will be ready for

use in approximately 15 seconds.

NOTE: Following the brew, your Brewer will fill in preparation for the next

brew. The pump will make a vibrating sound. This is normal.

Stopping the Brew Process

If you need to stop the brewing after the process has started, press the

Power Button to turn the Brewer ‘OFF’. The flow of coffee or tea will stop,

the heating element will shut off and the green light next to the Power

Button will disappear.

NOTE: You may get less coffee, tea or hot cocoa in your cup during your next

brew. We recommend that you perform a cleansing brew with water only after

a terminated brew. Then your NEXT brew will be the proper volume.

!$ $ 7!4% 2

$%  3#! , %

(%!4 ) .'

!54/ /& &

0/ 7%2

fig.

Brewing Hot Water

Your Brewer is able to produce hot water for making hot cocoa in a packet,

for use in cooking, for making soups, etc. Simply raise and lower the Handle

on the Brewer without adding a K-Cup

portion pack. The blue lights behind

the Brew Buttons on the LED Control Center will flash. Be sure to have a

mug or cup on the Drip Tray Plate and then press a Brew Button.

NOTE: After brewing a hot cocoa K-Cup, we recommend running a hot water

brew cycle without a K-Cup.

Purging the Brewer

If your Brewer has not been used for more than one week, you should purge

the water from the inner tank.

1. If there is water in the Water Reservoir, remove the Lid, then lift Reservoir

straight up and away from Brewer. Discard water, rinse and refill with

water. Place the Water Reservoir back on the Brewer and replace the

Lid. (If there is no water in Reservoir, simply refill.)

2. Be sure the Brewer is turned on. Raise and lower the Handle on the

Brewer without inserting a K-Cup and wait until the red light next to

‘HEATING’ turns off.

3. The blue lights behind the Brew Buttons on the LED Control Center

will flash. Be sure to have a mug or cup on the Drip Tray Plate and then

press a Brew Button.

4. Repeat steps 2 and 3 two more times to completely purge water

from inner tank.

If you are experiencing any problems with your Brewer, please contact

Customer Service at 1.866.901.BREW (2739).

SECTION 2

Controls & Indicators (LED Control Center)

Programming Auto Off Timer Feature

Set the Brewer to turn off two hours after the last brew.

1. Press the Power Button to turn on the Brewer.

2. Press the black Button to the right of the

‘AUTO OFF’ text on the LED Control Center

to turn on the Auto Off Timer feature (fig. 7)

The green light next to ‘AUTO OFF’ will

become illuminated. When the Auto Off Timer

is enabled, your Brewer will automatically

turn off two hours after your last brew.

3. To turn off the Auto Off Timer, simply press the

black Button again and the green light next to

‘AUTO OFF’ will turn off.

Cleaning External Parts

Regular cleaning of the Brewer’s external components is recommended.

1. Never immerse the Brewer in water or other liquids. The Housing and other

external components may be cleaned with a soapy, damp, non-abrasive cloth.

2. The Drip tray can accumulate up to 8 ounces of overflow. The Drip Tray

and Drip Tray Plate should be periodically inspected and rinsed clean. To

remove the Drip Tray Assembly, simply slide it toward you, keeping it level

at all times to avoid spilling. The Drip Tray and Drip Tray Plate are

dishwasher safe.

Cleaning the K-Cup Holder Assembly

1. Cleaning the Parts —The K-Cup

Holder

Assembly can be placed onto the top shelf of a

dishwasher. NOTE: Use low temperature cycles in

the dishwasher. To remove from the Brewer,

open the cover by lifting the Handle. Grasp the

top of the K-Cup Holder with one hand while

pushing up on the bottom of the K-Cup Holder

from underneath with the other until it releases

(fig. 8). After cleaning, align the K-Cup Holder

with the opening using the two front ribs as a

guide and snap into place from the top.

SECTION 3

Cleaning & Maintenance

fig.

AD D WATER

DE - SCA L E

HE ATIN G

AU TO OF F

PO W ER

fig.

2. Cleaning the Funnel —The Funnel can be

removed from the K-Cup Holder by pulling

on it until it pops off (fig. 9). The Funnel is

dishwasher safe. To replace it, just snap it

back onto the K-Cup Holder Assembly.

3. Cleaning the Exit Needle —The Exit Needle is

located on the inside bottom of the K-Cup

Holder Assembly. Should a clog arise due to

coffee grinds, it can be cleaned using a paper

clip or similar tool. Remove K-Cup Holder

assembly and detach Funnel. Insert the paper

clip (as shown in fig. 9) into the Needle to

loosen the clog and push it out. The K-Cup

Holder is dishwasher safe.

CAUTION: There are sharp needles that puncture

the K-Cup above the K-Cup Holder and in the

bottom of the K-Cup Holder. To avoid risk of injury,

do not put your fingers in the K-Cup Assembly

Housing.

Cleaning the Water Reservoir & Water Reservoir Lid

The Water Reservoir Lid should be cleaned with a damp soapy non-abrasive

cloth. Lid should not be put into the dishwasher. The Water Reservoir can

be placed into the top shelf of the dishwasher (use low temperature cycles)

for cleaning or can be cleaned with soapy water and rinsed thoroughly. Do

not dry the inside of the Water Reservoir with a cloth as lint may remain.

CAUTION: Please rinse the Water Reservoir thoroughly after cleaning to

ensure that no cleaners or cleaning solutions remain in this area as they may

contaminate the water supply in the Brewer.

De-Scaling Your Brewer

Mineral content in water varies from place to

place. Depending on the mineral content of the

water in your area, calcium deposits or scale

may build up in your Brewer. Scale is non-toxic,

but left unattended, it can hinder Brewer

performance. De-scaling your Brewer helps

maintain the heating element, and other

internal parts of the Brewer that come in

contact with water.

The Brewer should be de-scaled every 3-6

months to ensure optimal performance. It is

possible for calcium deposits to build up faster,

making it necessary to de-scale more often.

This Brewer is equipped with sensors to

detect when scale buildup is interfering with

the performance of the Brewer. When this is detected, the red light next

to ‘DE-SCALE’ will be illuminated. (fig. 10) However, even if the red light next

to ‘DE-SCALE’ is not illuminated you should continue to de-scale your

Brewer every 3 to 6 months.

You should promptly de-scale if ‘DE-SCALE’ is displayed on the LCD Control

Center. Properly follow the de-scaling procedure described.

NOTE: The Brewer will continue to function even when ‘DE-SCALE’ is displayed.

However, if you do not de-scale soon after it is displayed, continued scale build-

up could damage the Brewer. If this occurs, ‘DE-SCALE’ will begin to blink to alert

you to the potential damage to the Brewer if you do not de-scale immediately.

fig.

AD D WAT ER

DE - S CAL E

HE ATING

AU TO OFF

PO W E R

fig.

De-Scaling Instructions

A. PREPARE

Step 1: Make sure you have at least 48 ounces of undiluted white vinegar on

hand. You will also need an empty sink and a large mug (do not use a

paper cup).

Step 2: Empty the water in the Water Reservoir.

Step 3: Disable Auto Off feature.

B. FILL AND CLEAN

Step 1: Pour the vinegar into the Water Reservoir to fill.

Step 2: Place a large mug on the Drip Tray Plate and run a water brew cycle.

DO NOT USE A K-Cup, just press the Large Mug Button. Pour the

contents of the large mug into the sink.

Step 3: Repeat the brew process 3 times.

Step 4: Now let the Brewer stand for at least 4 hours while still on.

C. RINSE

Step 1: Ensure the Water Reservoir is filled with fresh water.

Step 2: Place a large mug on the Drip Tray Plate and run a water brew cycle

without using a K-Cup

. Pour the contents of the large

mug into the sink.

Step 3: Repeat brew process until the Water Reservoir is empty.

Step 4: You may need to perform additional water brew cycles if you notice

any residual taste.

NOTE: If the red ‘DE-SCALE’ light is still illuminated on the LED Control Center

after completing the procedure, repeat the de-scaling procedure above.

Service

Beyond these recommended cleaning and maintenance procedures this

Brewer is not user serviceable, for service please refer to the Warranty

section of this guide.

Storage

Empty the Water Reservoir before storing and take care to ensure that you

store your Brewer in a safe and frost free environment. Please be sure to

store your Brewer in its upright position to avoid water leakage from the inner

tank. If you store the Brewer in a cold environment, you run the risk of water

freezing inside the Brewer and causing damage. When you prepare to use it

after storage, we recommend rinsing the Water Reservoir with fresh water

and running three cleansing brews without a K-Cup.

If you plan to move your Brewer to a different location, turn the Brewer off,

unplug it and empty the Water Reservoir. If your Brewer has been in

an environment below freezing, please be sure to let it warm to room

temperature for at least 2 hours before using.

SECTION 3 Cleaning & Maintenance

1212

SECTION 4 Troubleshooting

Situation

Brewer does not

have power

Brewer will not

brew when used for

the first time

Brewer will not brew

Solution

• Plug Brewer into an independent outlet.

• Check to be sure that it is plugged in securely.

• Plug into a different outlet.

• Reset your home’s circuit breaker if necessary.

• Make sure that the Power Button has been

turned on and the power light is illuminated.

• The Brewer must be primed for use by filling the

internal hot water tank before the first brew. The

red light next to ‘DE-SCALE’ on the LED Control

Center will flash. (refer to page 6)

• If Brewer is cold/frozen, wait for at least two

hours for it to reach room temperature before

powering on.

• After placing the K-Cup portion pack in the K-Cup

Holder, make sure that the Handle is pushed down

securely and the Blue lights behind the Brew

Buttons on the LED Control Center are flashing.

• If the blue light next to ‘ADD WATER’ on the LED

Control Center is illuminated, add water to Water

Reservoir or make sure the Water Reservoir is

seated properly in its base.

• If the blue light next to ‘ADD WATER’ on the

LED Control Center continues to be on even

after refilling, contact Customer Service at

1.866.901.BREW (2739).

Situation

Brewing a partial cup

Brewer shuts off

automatically

Solution

• The Exit Needle may be clogged. (refer to page 11).

• Clean K-Cup Holder if necessary and rinse under

faucet. (refer to page 10).

• The Water Reservoir may have been removed

during brewing. Replace the Water Reservoir and

perform a water brew without a K-Cup.

• If the red ‘DE-SCALE’ light is illuminated, descale

the Brewer (refer to page 11).

• If you have repeated the de-scale procedure on

your Brewer two times and it is still only brewing

a partial cup, contact Customer Service at

1.866.901.BREW (2739).

• Check to make sure that the Auto Off Timer

feature has not been set. If the green light next

to ‘AUTO OFF’ on the LED Control Center is

illuminated, press the black Button to turn off

the Auto Off Timer feature.

If any problems persist, contact Customer Service at 1.866.901.BREW (2739)

SECTION 5 Warranty

Limited One Year Warranty

Keurig

warrants that your Brewer will be free of defects in materials or

workmanship under normal home use for one year from the date of

purchase. It is recommended that you fill out and return the warranty card

enclosed with your Brewer so that your purchase information will be stored

in our system. Keurig will, at its option, repair or replace the Brewer without

charge upon its receipt of proof of the date of purchase. If a replacement-

Brewer is necessary to service this warranty, the replacement Brewer may

be new or reconditioned. If a replacement Brewer is sent, a new limited one

year warranty will be applied to the replacement Brewer.

This warranty only applies to Brewers operated in the United States and

Canada. This warranty gives you specific legal rights, and you may also have

other rights that vary from state to state and, in the case of Canada, from

Province to Province.

What is not covered by the Limited Warranty?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL

DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER

INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH

OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or Provinces

do not allow the exclusion or limitations of incidental or consequential

damages, so the above limitation or exclusion may not apply to you

depending on the state or Province of purchase.

Nor does this warranty cover damages caused by services performed by

anyone other than Keurig or its authorized service providers, use of parts

other than genuine Keurig parts, or external causes such as abuse, misuse,

inappropriate power supply or acts of God.

Other Limitations

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS

WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY

SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO

YOUR B40 BREWER, INCLUDING ANY IMPLIED WARRANTY OF MER-

CHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some

states or Provinces do not allow disclaimers of such implied warranties or

limitations on how long an implied warranty lasts, so the above limitation

may not apply to you depending on the state or the Province of purchase.

How do you obtain warranty service?

Keurig Brewers are high quality appliances and, with proper care, are

intended to provide years of satisfying performance. However, should the

need arise for warranty servicing, simply call Keurig Customer Service at

our toll free phone number 1.866.901.BREW (2739). Please do not return your

Brewer for servicing without first speaking to Keurig Customer Service to

obtain an Authorization to Return number (ATR). Keurig Brewers returned

without an ATR number will be returned to the sender without servicing.

Keurig, Incorporated

55 Walkers Brook Drive

Reading, MA 01867

1.866.901.BREW (2739)

Lors de l’utilisation de tout appareil électrique, des

mesures de sécurité de base devraient être suivies,

et notamment :

1. Lire toutes les instructions avant l’utilisation.

2. Ne pas toucher les surfaces chaudes. Utiliser

les poignées s’il y en a.

3. Installer correctement l’appareil et le placer

dans un endroit conforme aux présentes

instructions avant de l’utiliser.

4. L’utilisation d’accessoires non recommandés

par le fabricant de l’appareil risque de causer

des incendies, des chocs électriques ou des

blessures.

5. Éviter le contact ou la proximité de l’appareil

avec un élément électrique ou un brûleur à

gaz. Éviter également de placer l’appareil à

l’intérieur d’un four chaud.

6. Ne pas utiliser à l’extérieur.

7. Pour éviter les risques d’incendie, de chocs

électriques ou de blessures, ne pas immerger

la fiche, le cordon d’alimentation ou l’appareil

dans l’eau ni dans aucun autre liquide.

8. Ne pas trop remplir le réservoir d’eau.

9. Utiliser seulement de l’eau dans cet appareil!

Ne verser aucun autre liquide ou aliment dans

le réservoir d’eau à l’exception des produits

mentionnés dans les instructions de nettoyage

du présent manuel.

10. Éteindre et débrancher l’appareil avant de

le nettoyer ou d’en faire l’entretien. Laisser

l’appareil refroidir avant d’ajouter ou d’enlever

des pièces et avant de le nettoyer.

11. Pour une utilisation optimale, brancher

l’appareil dans une prise de courant séparée

sur un circuit spécialisé pour éviter que les

lumières vacillent, que les fusibles sautent ou

que les disjoncteurs se déclenchent.

12. Ne jamais utiliser un appareil dont la fiche ou

le cordon d’alimentation est endommagé ou

un appareil qui présente un trouble de fonc-

tionnement ou qui a été endommagé. Commu-

niquer avec le Service à la clientèle de Keurig

pour signaler tout mauvais fonctionnement de

la cafetière ou tout dommage à celle-ci.

13. Ne pas laisser le cordon d’alimentation pendre

d’une table ou d’un comptoir ni entrer en con-

tact avec une surface chaude.

14. Pour débrancher la cafetière, appuyer sur

le bouton de mise en marche (POWER) situé

sur le dessus de la cafetière pour éteindre

l’appareil, puis retirer le cordon de la prise.

15. Ne jamais laisser des enfants utiliser la cafetière

ni rester à proximité sans surveillance.

16. Ne pas soulever la poignée pour ouvrir le cou-

vercle de la cafetière durant l’infusion.

17. Toujours laisser le couvercle sur le réservoir

d’eau, sauf lors du remplissage.

18. L’appareil est équipé d’un cordon

d’alimentation muni d’un fil et d’une prise

de mise à la terre. L’appareil doit être mis à

la terre en utilisant une prise de courant à

contact de mise à la terre à trois trous. En cas

de court-circuit, la mise à la terre réduit les

risques de chocs électriques.

19. Si la prise de courant est une prise de courant

murale standard à deux trous, le propriétaire

a l’obligation et la responsabilité de la faire

remplacer par une prise de courant de mise à

la terre à trois trous.

20. Il ne faut en aucun cas couper ou enlever

la troisième broche (mise à la terre) de la

fiche du cordon d’alimentation, ni utiliser un

adaptateur.

21. Consulter un électricien qualifié si les

instructions sur la mise à la terre ne sont pas

parfaitement comprises ou en cas de doutes

sur la mise à la terre de l’appareil.

22. Ne pas utiliser l’appareil pour une fin autre

que celle pour laquelle il a été conçu.

CONSERVER CE

MANUEL.

RÈGLES DE SÉCURITÉ IMPORTANTES

Fonctionnement et utilisation sans danger

ATTENTION : Le godet K-Cup

est perforé par deux aiguilles, une au-dessus du

support à K-Cup et l’autre au fond du support à K-Cup. Pour éviter tout risque de

blessure, ne pas mettre les doigts dans le compartiment de la K-Cup.

ATTENTION : L’eau se trouvant dans le support à K-Cup durant l’infusion est

extrêmement chaude. Pour éviter tout risque de blessure, ne pas soulever la

poignée ni ouvrir le boîtier du support à K-Cup durant l’infusion.

INSTRUCTIONS POUR CORDON D’ALIMENTATION COURT : L’appareil est doté

d’un cordon d’alimentation court pour éviter qu’il s’emmêle ou que quelqu’un

trébuche sur un cordon long.

Si une rallonge est utilisée, (1) les caractéristiques électriques inscrites sur

la rallonge doivent égaler ou excéder celles de l’appareil, (2) le cordon doit

être fixé de façon à ce qu’il ne pende pas d’une table ou d’un comptoir pour

éviter qu’un enfant puisse le saisir ou que quelqu’un trébuche et (3) la ral-

longe doit être munie d’une prise de mise à la terre à trois broches.

CE PRODUIT EST DESTINÉ À UNE UTILISATION DOMESTIQUE SEULEMENT

AVERTISSEMENTCE PRODUIT CONTIENT DES PRODUITS

CHIMIQUES, NOTAMMENT DU PLOMB, UN MÉTAL QUI, SELON L’ÉTAT DE

LA CALIFORNIE, CAUSE LE CANCER, DES ANOMALIES CONGÉNITALES OU

D’AUTRES MALFORMATIONS GÉNÉTIQUES.

TABLE DES MATIÈRES

SYSTÈME D’INFUSION GOURMET UNE TASSE À LA

FOIS DE KEURIG

Elite — Modèle B40

RÉGLAGES

Conseils utiles ..................................................................................17

Déballage ...........................................................................................17

Caractéristiques ...............................................................................18

SECTION 1 — PRÉPARATION ET PREMIÈRE INFUSION

Préparation et première infusion ...................................................19

SECTION 2 — COMMANDES ET VOYANTS

Programmation de la fonction

de minuterie d’arrêt automatique ..................................................23

SECTION 3 — NETTOYAGE ET ENTRETIEN

Nettoyage ...........................................................................................23

Détartrage ..........................................................................................24

Entreposage .......................................................................................26

SECTION 4 — DÉPANNAGE ...............................................................26

SECTION 5 — GARANTIE ...................................................................27

Inscrivez le numéro de série de votre cafetière ici.

Le retrait de l’étiquette du numéro de série annulera la garantie.

AVERTISSEMENT

AVERTISSEMENT : POUR RÉDUIRE LES RISQUES

D’INCENDIE ET DE CHOCS ÉLECTRIQUES, NE PAS RETIRER

LE COUVERCLE INFÉRIEUR. CET APPAREIL NE CONTIENT

AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR. LES

RÉPARATIONS NE DEVRAIENT ÊTRE EFFECTUÉES QUE

PAR UN TECHNICIEN DE SERVICE AGRÉÉ.

RISQUE D’INCENDIE ET DE

CHOCS ÉLECTRIQUES

NE PAS OUVRIR!

Réglages

Conseils utiles

1. Laissez votre cafetière en marche en tout temps.

Nous vous suggérons de toujours laisser votre

cafetière allumée. Vous pourrez ainsi savourer

une tasse de café, de thé ou de chocolat chaud

fraîchement infusé à tout moment. Vous pouvez

toutefois régler votre cafetière pour qu’elle

s’éteigne automatiquement deux heures après

la dernière infusion. Veuillez consulter les

instructions de la page 23 pour que le réglage

de votre cafetière réponde à vos besoins.

2. Pour obtenir le meilleur café gourmet, thé de

spécialité ou chocolat chaud possible, Keurig

recommande l’utilisation d’eau embouteillée ou

filtrée.

La qualité de l’eau varie d’un endroit à l’autre.

Si votre café a un goût désagréable de chlore

ou de minéraux, nous vous recommandons

d’utiliser de l’eau embouteillée ou de l’eau

filtrée à l’aide d’un système de filtration d’eau.

3. Choisissez le format, la saveur et l’infusion que

vous aimez.

Avec plus de 200 variétés de K-Cups et deux

formats d’infusion : petite tasse de 155 ml

(5,25 oz) et tasse moyenne de 214 ml (7,25 oz),

votre cafetière Keurig vous offre d’infinies pos-

sibilités de formats, de saveurs et d’infusions

pour préparer la boisson idéale pour vous. Pour

une boisson forte au goût plus prononcé,

choisissez une K-Cup très intense, qui contient

30 % plus de café que nos cafés ordinaires, et

le format d’infusion qui vous convient. Plus le

format d’infusion est petit, plus la saveur sera

forte. Plus le format d’infusion est grand, plus

la saveur seradouce.

4. Branchez la cafetière sur un circuit avec mise

à la terre où elle seule est branchée.

Une surcharge du circuit électrique avec

plusieurs appareils risque de nuire au fonc-

tionnement de votre cafetière. Celle-ci devrait

être branchée séparément des autres appar-

eils, sur son propre circuit électrique.

5. Infusez votre café dans une tasse de voyage.

Pour infuser un café dans une tasse de voyage,

vous n’avez qu’à retirer la cuvette d’égouttage

et à placer la tasse de voyage sur la base de la

cuvette.

6. Détartrez régulièrement la cafetière.

Voir les instructions à la page 25.

Déballage de la cafetière

1. Placez la boîte de la cafetière sur une grande

surface plane, comme une table ou un comptoir,

ou sur le plancher. Ouvrez la boîte.

2. Enlevez la documentation fournie.

3. Couchez l’emballage sur le côté, la partie avant

de la boîte en dessous.

4. Saisissez le sac de plastique contenant la

cafetière.

5. Tirez soigneusement le sac de plastique (et le

matériel d’emballage) vers vous pour le sortir

de la boîte. La cafetière est encastrée dans le

polymousse et repose sur le côté.

6. Retirez la partie supérieure du polymousse.

7. Retirez soigneusement la cafetière de la base

de polymousse et placez-la debout sur une

surface plane et stable.

8. Enlevez le sac de plastique de la cafetière.

9. Inscrivez le numéro de série de la cafetière à

la page 16 de ce manuel. Le numéro de série

est indiqué sous la boîte de la cafetière, de

même que sur la cafetière, derrière la cuvette

d’égouttage (visible quand on retire la cuvette).

10. Placez la cafetière debout sur une surface

plane et stable. Enlevez le ruban adhésif qui

maintient le réservoir d’eau en place.

Nous vous recommandons de conserver tout le

matériel d’emballage au cas où il serait néces-

saire de retourner la cafetière.

AVERTISSEMENT :

Gardez tous les sacs

de plastique hors de la portée

des enfants.

Caractéristiques Cafetière Elite — Modèle B40

A. Couvercle du

réservoir d’eau

B. Réservoir d’eau

C. Fentes pour languettes

de verrouillage du

réservoir d’eau

D. Poignée

E. Entonnoir

F. Support à godet K-Cup

(E et F forment

I’assemblage du

support à K-Cup)

G. Couvercle

H. Boîtier de l’assemblage

du support à godet K-Cup

I. Boîtier

J. Plateau à tasse

K. Cuvette d’égouttage

L. Base de la cuvette

d’égouttage

M. Évent

N. Cordon d’alimentation

O. Bouton Tasse moyenne

P. Bouton Grande tasse

Q. Bouton de mise en

marche (POWER)

R. Voyant vert de mise en

marche (POWER)

S. Bouton d’arrêt automa-

tique (AUTO OFF)

T. Voyant vert d’arrêt au-

tomatique (AUTO OFF)

U. Voyant rouge de

chauffage (HEATING)

V. Voyant rouge de détar-

trage (DE-SCALE)

W. Voyant bleu Ajouter de

l’eau (ADD WATER)

Cafetière Elite B40 Commandes et voyants

!$ $ 7!4% 2

$%  3#! , %

(%!4 ) .'

!54/ /& &

0/ 7%2

SECTION 1 Préparation et première infusion

Préparation de votre

cafetière

1. Déballez le cordon et branchez la

cafetière dans une prise avec mise à la

terre. Retirez tous les rubans adhésifs.

2. Placez une grande tasse (au moins

296 ml/10 oz) sur le plateau à tasse.

3. Retirez le réservoir d’eau de la cafetière

en enlevant le couvercle du réservoir

(fig. 1), puis en soulevant le réservoir à

la verticale et en le tirant ensuite vers

l’avant de la cafetière (le réservoir peut

offrir une certaine résistance). Rincez à

l’eau courante.

IMPORTANT

N’utilisez pas votre cafetière Keurig

avant de l’avoir préparée pour une première utilisa-

tion, tel qu’indiqué ci-dessous.

REMARQUE:

Si la cafetière a été placée dans un

endroit où la température était sous le point de con-

gélation, il est recommandé de laisser la cafetière au

moins deux heures à la température ambiante avant

de la préparer. Une cafetière gelée ou très froide ne

pourra pas être préparée.

4. Remplissez le réservoir d’eau filtrée ou em-

bouteillée jusqu’à ce que le niveau atteigne la

ligne juste en dessous de la limite supérieure de

la fenêtre translucide. (Attention de ne pas trop

le remplir.)

5. Replacez la base du réservoir d’eau sur le côté

gauche de la cafetière et assurez-vous que

les languettes de verrouillage du réservoir

s’engagent correctement dans la cafetière (fig. 2).

Replacez le couvercle sur le réservoir d’eau.

6. Appuyez sur le bouton de mise en marche

(POWER) situé sur le panneau supérieur droit de

la cafetière. Le voyant vert de mise en marche

(POWER) s’allumera.

7. Le voyant rouge de détartrage (DE-SCALE) du

panneau de commande à DEL clignotera pour in-

diquer que la cafetière a besoin d’être préparée.

Assurez-vous que la poignée est complètement

abaissée avant de continuer.

REMARQUE : La procédure de préparation se fait

sans K-Cup.

8. Appuyez sur le bouton clignotant Tasse moyenne

(fig. 3). REMARQUE : Si le réservoir d’eau est vide

ou mal installé sur la cafetière, le voyant bleu

Ajouter de l’eau (ADD WATER) s’allumera sur le

panneau de commande à DEL. Le bouton Tasse

moyenne ne peut être activé tant que de l’eau n’est

pas ajoutée au réservoir.

ﬁg.

!$ $ 7!4 %2

$%  3#! , %

(%!4 ) .'

!54/ /& &

0/ 7%2

Tasse

moyenne

ﬁg.

20 21

Infusion de votre première

tasse

1. Le voyant vert de mise en marche (POWER)

sur le panneau de commande à DEL sera

allumé pour indiquer que la cafetière est en

marche.

2. Placez une tasse sur le

plateau à tasse.

3. Soulevez la poignée, et le

support à K-Cup s’ouvrira

(fig. 4).

4. Choisissez un godet

K-Cup

. REMARQUE : Ne

perforez pas la K-Cup et

n’enlevez pas son couvercle d’aluminium.

5. Placez un godet K-Cup dans le support à

K-Cup (fig. 5).

ATTENTION : Le godet K-Cup est perforé par

deux aiguilles, une au-dessus du support à K-

Cup et l’autre au fond du support à K-Cup. Pour

éviter tout risque de blessure, ne pas mettre les

doigts dans le support à K-Cup.

Abaissez complètement la poignée pour

fermer le couvercle.

7. Choisissez le format d’infusion : le bouton

Tasse moyenne produira une boisson de

214 ml (7,25 oz) et le bouton Grande tasse,

une boisson de 274 ml (9,25 oz).

9. La cafetière se remplit automatiquement (préparation) et l’eau est

chauffée. Ce processus prend environ trois minutes. Durant la période

de chauffage, le voyant rouge de chauffage (HEATING) du panneau de

commande à DEL s’allumera. Lorsque l’eau sera chaude, le voyant rouge

s’éteindra et le bouton Tasse moyenne clignotera.

REMARQUE : Ne soulevez pas la poignée de la cafetière pendant le cycle de

préparation.

REMARQUE : Durant le cycle de préparation et lors des périodes de chauffage

subséquentes, il est possible qu’une petite quantité d’eau s’échappe de l’évent et

dégoutte dans le réservoir. C’est normal.

10. Appuyez sur le bouton Tasse moyenne pour effectuer une infusion de

nettoyage. Jetez l’eau qui s’est écoulée.

11. La cafetière peut prendre jusqu’à 15 secondes pour chauffer l’eau entre

les infusions, période pendant laquelle le voyant rouge de chauffage

(HEATING) peut s’allumer. Lorsque l’eau est chaude, le voyant rouge

s’éteint.

12. Le processus de préparation est maintenant terminé et vous êtes prêt à

faire votre première infusion!

ﬁg.

SECTION 1 Préparation et première infusion

La page charge ...

Keurig Elite B40 Le manuel du propriétaire

Marque: Keurig

Modèle: Elite B40

Catégorie: Cafetières

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Keurig Elite B40 Owner's manual

Documents connexes

Autres documents

ROOMS TO GO 83600126 Assembly Instructions