Keurig Select B77 Le manuel du propriétaire

Marque: Keurig

Modèle: Select B77

Catégorie: Accessoires de préparation de café

Taper: Le manuel du propriétaire

USING YOUR BREWER

OWNER’S MANUAL: Getting the most from your new

Select B77 Keurig

Brewer

COMMENT UTILISER VOTRE CAFETIÈRE

MANUEL D’UTILISATION : Tirez le meilleur de votre

nouvelle cafetière Select B77 de Keurig

IMPORTANT SAFEGUARDS Safe Operation & Use

When using electrical appliances, basic

safety precautions should be followed,

including the following:

Read all instructions before using.

2. Do not touch hot surfaces. Use handle and

knobs when available.

3. This appliance must be properly installed and

located in accordance with these instructions

before it is used.

4. The use of accessory attachments not recom-

mended by the appliance manufacturer may re-

sult in fire, electrical shock or injury to persons.

5. Do not place on or near a hot gas or electric

burner, or in a heated oven.

6. Do not use outdoors.

7. To protect against fire, electric shock and injury,

do not immerse cords, plugs or the appliance in

water or any other liquid.

8. Do not overfill the Water Reservoir with water.

9. Use only water in this appliance! Do not put any

other liquids or foods in the Water Reservoir,

except as instructed in the Cleaning Instructions

in this guide.

10. Turn off and unplug the Brewer before

cleaning or maintenance. Allow to cool

before putting on or taking off parts and

before cleaning the appliance.

11. For best operation, plug the appliance into

its own electrical outlet on a dedicated circuit

to prevent flickering of lights, blowing of fuses

or tripping a circuit breaker.

12. Do not operate any appliance with a damaged

cord or plug, or after the appliance malfunc-

tions or is damaged in any manner. Contact

Keurig Customer Service to report any

malfunction of or damage to the Brewer.

13. Do not let the cord hang over the edge

of the table or counter, or touch hot surfaces.

14. To disconnect, press the Power Button on

the back of the Brewer to “OFF” status, and

then remove the plug from the wall outlet.

15. Close supervision is necessary when

any appliance is used by or near children.

16. Do not lift the Brewer Handle while

brewing is in progress.

17. Always keep the Water Reservoir Lid on the

Water Reservoir unless you are refilling it.

18. This appliance is equipped with a power

cord having a grounding wire with a

grounding plug. The appliance must be

grounded using a 3-hole, properly grounded

outlet. In the event of an electrical short

circuit, grounding reduces the risk of

electrical shock.

19. If the outlet is a standard 2-prong wall

outlet, it is your personal responsibility

and obligation to have it replaced with a

properly grounded 3-prong wall outlet.

20. Do not, under any circumstances, cut or

remove the third (ground) prong from

the power cord or use an adapter.

21. Consult a qualified electrician if the

grounding instructions are not completely

understood or if doubt exists as to whether

the appliance is properly grounded.

22. Do not use the appliance for any reason

other than its intended use.

SAVE THESE INSTRUCTIONS.

WARNING TO USERS AND PARENTS

1. DO NOT permit children to use brewer unless there

is adult supervision. Brewer dispenses very hot water.

2. SPECIAL NOTICE FOR HOT COCOA USERS:

IMMEDIATELY AFTER USING A HOT COCOA K-CUP,

RUN a Hot Water Brew Cycle without a K-Cup to avoid

the possibility of clogging the exit needle. DO NOT assume

the next user will do this.

CAUTION: There are two sharp needles that puncture the K-Cup

portion pack,

one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To

avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.

CAUTION: There is extremely hot water in the K-Cup Holder during the

brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup

Assembly Housing during the brewing process.

SHORT CORD INSTRUCTIONS:

A short power supply cord is provided to

reduce the risk of becoming entangled in or tripping over a longer cord.

If an extension cord is used, (1) the marked electrical rating of the cord set

or extension cord should be at least as great as the electrical rating of the

appliance; (2) the cord should be arranged so that it will not drape over the

countertop or tabletop where it can be pulled on by children or tripped over un-

intentionally; and (3) the extension cord must include a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING

LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,

BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

TABLE OF CONTENTS

KEURIG

GOURMET SINGLE CUP HOME BREWING SYSTEM

Select B77 — Using Your Brewer

SET-UP

Helpful Hints ........................................................................................4

Unpacking ............................................................................................4

Features ...............................................................................................5

SECTION 1 — SET-UP & FIRST BREW

Set-Up & First Brew ...........................................................................6

SECTION 2 — CONTROLS & INDICATORS

Setting the Clock ...............................................................................10

Programming On/Off Features ......................................................10

Programming Brew Size .................................................................12

SECTION 3 — CLEANING & MAINTENANCE

Cleaning ..............................................................................................13

De-Scaling..........................................................................................14

Storage ...............................................................................................15

SECTION 4 — TROUBLESHOOTING ..................................................16

SECTION 5 — WARRANTY ................................................................17

Pour des directives en français, veuillez vous reporter à la page 18.

Record your Brewer Serial Number here.

WARNING

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT REMOVE THE

BOTTOM COVER. NO USER SERVICEABLE

PARTS ARE INSIDE. REPAIR SHOULD BE DONE

BY AUTHORIZED SERVICE PERSONNEL ONLY.

Removing the serial number label from the Brewer will void warranty.

RISK OF FIRE OR

ELECTRIC SHOCK

DO NOT OPEN

Set-Up

Helpful Hints

1. Keep your Brewer turned “ON” at all times.

To brew a fresh cup of coffee, tea or hot cocoa

anytime you want, we suggest you keep your

Brewer turned “ON” all the time. However, the

Brewer is fully programmable so you can set it

to turn on and off automatically to match your

schedule. Or, if you prefer, set the Brewer to

automatically turn off after a period of time.

Follow the simple instructions on pages 10–12

to make using the Brewer convenient for you.

2. For the best tasting gourmet coffee, tea or

hot cocoa, Keurig recommends using bottled

or filtered water.

Water quality varies from place to place. If you

notice an undesirable taste in your cup of

coffee, such as chlorine or other mineral tastes,

we recommend you consider using bottled

water or water from a filtration system.

3. Customize the Size, Flavor & Brew That’s

Perfect for You.™

With the choice of over 200 varieties of K-Cups

and 4 brew sizes (Iced Beverage-3.25 oz., Small

Cup-5.25 oz., Small Mug-7.25 oz., and Large

Mug-9.25 oz.) your Keurig

Brewer gives you

endless options to customize the size, flavor

and brew that’s perfect for you. For a strong,

intense cup, select an Extra Bold K-Cup

(with

up to 30% more ground coffee than regular

varieties) and brew size that’s right for you. The

smaller the brew size, the more intense flavor

in your cup. The larger the brew size, the less

intense flavor in your cup.

4. Plug Brewer into its own grounded outlet.

If the electric circuit is overloaded with other

appliances, your Brewer may not function

properly. The Brewer should be operated on its

own circuit, separate from other appliances.

5. Brewing into a travel mug.

To brew into a travel mug, simply remove the

Drip Tray Assembly and place the travel mug

on the Drip Tray Base.

6. De-Scale Brewer regularly.

Please see pages 14 and 15 for instructions.

Unpacking Instructions

1. Place Brewer box on a large steady surface

(such as a table or countertop) or on the floor.

Open the box.

2. Remove enclosed literature.

3. Turn the box on its side with front of box face down.

4. Reach into the box and grasp the plastic bag

that contains the Brewer.

5. Carefully pull the plastic bag (and packaging

materials) toward you and out of the box. The

Brewer will still be encased in the polyfoam

and be on its side.

6. Remove the top polyfoam packaging material.

7. Carefully lift Brewer off of the bottom polyfoam

and place it upright on a flat, steady surface.

8. Lift plastic bag off of Brewer.

9. Record the serial number for this Brewer on

page 3 of this guide. The serial number can be

found on the bottom of the Brewer box or on the

Brewer behind the Drip Tray (when removed).

10. Place the Brewer upright on a flat, steady

surface. Remove tape holding Water Reservoir

in place.

We recommend you save all packing materials in

case future shipping of the product is necessary.

WARNING:

Keep all plastic bags away

from children.

ME N U

BR E W

ME N U

READY

TO BREW

Features Select — Model B77 Brewer

A. Water Reservoir Lid

B. Water Reservoir

C. Water Reservoir

Lock Tab Slot

D. Handle

E. Funnel

Select B77 Brewer

Controls

and Indicators

P. LCD Control Center

Q. Left Button

R. Right Button

S. MENU Button

T. BREW Button

F. K-Cup

Portion Pack

Holder (E and F are the

K-Cup Holder Assembly)

G. Lid

H. K-Cup

Portion Pack

Assembly Housing

I. Housing

J. Drip Tray Plate

K. Drip Tray

L. Drip Tray Base

M. Vent

N. Power Cord

O. Power Switch (Not

shown) Located Rear

Right Side of Brewer

SECTION 1 Set-Up & First Brew

PRIME

ME NU

BR EW

ME NU

READY

NOT

Setting Up Your Brewer

1. Unwrap cord and plug the Brewer into

a grounded outlet. Remove all pieces of

packing tape and clear plastic sticker

from LCD display.

2. Place a Large Mug (10 oz. minimum) on the

Drip Tray Plate.

3. Remove the Water Reservoir from Brewer

by first removing Lid from Reservoir (fig. 1),

then lifting Reservoir straight up and toward

front of Brewer (may be tight), (fig. 2). Rinse

with fresh water.

4. Fill Water Reservoir with bottled or filtered

water so that the water level is just below the

top edge of the Water Reservoir.

IMPORTANT: You cannot use your Keurig

Brewer until

it has been set up for its ﬁrst use as set forth below.

NOTE: If Brewer has been exposed to temperatures

below freezing, allow Brewer at least two hours to

reach room temperature before brewing. A frozen

or extremely cold Brewer will not operate.

5. Place Water Reservoir base into

the left side of the Brewer and be

sure the Water Reservoir Lock Tab

engages with the Brewer. Replace

Lid on Water Reservoir.

6. Press and release the Power

Switch found directly behind the

Brewer. Switch is spring loaded

and will return to original position.

7. The Blue LCD Control Center will

come on and indicate “NOT READY”

and the BREW Button will flash.

NOTE: A K-Cup should not be used

for this Sequence

8. The Brewer will automatically fill the internal

tank with water and then the water will be

heated. This will take about 4 minutes.

During the heating period, “NOT READY”

(fig. 3) is displayed on the LCD Control Center.

Do not lift Brewer Handle during this

‘heating period’. Once the water is heated,

“READY TO BREW” will be displayed and the

BREW Button will flash (fig. 4).

NOTE: You may see small amounts of water

coming from the Vent and dripping into the

Water Reservoir during this and subsequent

heating — this is normal.

ﬁg.

Lock Tab

5. Place a K-Cup portion pack

in the K-Cup Holder (fig. 6).

CAUTION: There are two sharp needles that

puncture the K-Cup, one above the K-Cup Holder

and the other in the bottom of the K-Cup Holder.

To avoid risk of injury, do not put your fingers in

the K-Cup Assembly Housing.

Lower the Handle to close the Lid over the

K-Cup Holder. (When it is closed completely,

the LCD Control Center will indicate “READY

TO BREW”. The Left and Right Buttons will

be lit and the BREW Button will flash up to 60

seconds.)

a. All brew size icons are lit with the default

size flashing (fig. 7). To choose a different size,

press Left Button to go down in size or Right

Button to go up in size.

NOTE: The Small Mug (7.25 oz. serving) is the

factory set default brew size. To program your

favorite brew size see page 12 “Programming

Your Brew Size”.

Your choices are a stronger Small Cup (5.25

oz. serving), a Small Mug (7.25 oz. serving), a

Large Mug (9.25 oz. serving) or Iced Beverage

setting (3.25 oz. serving).

c. To use the Iced Beverage setting, place a tall

9. Press the BREW Button to start a cleansing

brew without a K-Cup. Pour the hot water into

the sink.

NOTE: A K-Cup should not be used for this

Sequence

10. The one-time set-up process is now

complete and you are ready to brew!

NOTE: The Brewer may take 15-30 seconds

between brews and then “READY TO BREW”

will be displayed.

Ready to Brew Your First Cup

1. LCD Control Center will indicate

“READY TO BREW”.

2. Place a cup or mug on the Drip Tray Plate.

3. Lift the Handle and the K-Cup

Holder

will open toward you (fig. 5).

4. Select a K-Cup portion pack.

NOTE: Do not remove the foil

lid or puncture the K-Cup.

ME NU

BR EW

ME NU

READY

TO BREW

ﬁg.

ME NU

BR EW

ME NU

READY

TO BREW

ﬁg.

glass filled with ice on the Drip Tray Plate. Use

your favorite K-Cup

, select the Iced Beverage

(3.25 oz.) brew size and press the BREW But-

ton. Add more ice once brewing is complete,

add cream and sugar if desired.

d. Once size is chosen, press BREW Button.

BREW Button will stop flashing, Left and Right

Buttons will no longer be lit and icon

of brew size will be lit.

7. The LCD Control Center will now display the

word ‘BREWING’ and the serving size you

selected will be illuminated on LCD (fig. 8).

CAUTION: There is extremely hot water in the K-

Cup Holder during the brew process. To avoid risk

of injury, do not lift the Handle or open the

K-Cup Assembly Housing during the brew process.

There may be a short pause prior to coffee

being dispensed. The entire brew process lasts

for approximately 1 minute and ends with a

burst of air to remove all liquid from the K-Cup.

9. Lift the Handle, remove and dispose

of the used K-Cup.

CAUTION: K-Cup will be hot.

Brewing Your First Cup (Continued)

10. Enjoy your first cup of Keurig Brewed

gourmet coffee, tea or hot cocoa!

11. Your Brewer may display “NOT READY” as

it heats water for the next brew cycle. The

“READY TO BREW” indication will return to

the LCD Control Center in about 15 seconds.

Stopping the Brew Process

If you need to stop the brewing after the process has started, press and

release the Power Switch to turn the Brewer ‘OFF’. The flow of coffee, tea

or hot cocoa will stop, the heating element will shut off and the blue lights

illuminating the LCD Control Center and Water Reservoir will disappear.

NOTE: You may get more coffee, tea or hot cocoa in your cup during your next

brew. We recommend that you perform a cleansing brew with water-only after

a terminated brew. Then your NEXT brew will be the volume you have selected.

Adding Water

The LCD Control Center of your Brewer will indicate when the water level

in the tank is low or if the Water Reservoir has been removed by displaying

the words “ADD WATER” (fig. 9). The blue light in the Water Reservoir will

also blink when water needs to be added. The Brewer will not allow you to

brew when “ADD WATER” is displayed (fig. 9).

SECTION 1

Set-Up & First Brew

Small Cup

(5.25 oz.)

Small Mug

(7.25 oz.)

Large Mug

(9.25 oz.)

Iced Beverage

(3.25 oz.)

ME NU

BR EW

ME NU

BREWING

fig.

The Water Reservoir can be filled in two ways.

1. Lift off the Water Reservoir Lid and pour

water directly into the Water Reservoir

while it is still attached to the Brewer,

then replace the Lid.

2. Remove the Water Reservoir from Brewer by

first removing Lid from the Water Reservoir, then

lifting the Water Reservoir straight up and toward

front of Brewer. Fill with water. Place the Water

Reservoir back on the Brewer and replace the Lid.

IMPORTANT: Do not remove the Water Reservoir

during the brewing process.

Brewing Hot Water

Your Brewer is able to produce hot water for making hot cocoa from a packet,

for use in cooking, for making soups, etc. Simply follow the instructions on

page 7 — “Ready To Brew Your First Cup” without adding a K-Cup.

NOTE: After brewing a hot cocoa K-Cup, we recommend running a hot water

brew cycle without a K-Cup.

Purging the Brewer

If your Brewer has not been used for more than one week, you should purge

the water from the inner tank.

1. If there is water in the Water Reservoir, remove the Lid, then lift the

Water Reservoir straight up and away from Brewer. Discard water, rinse

and refill with water. Place the Water Reservoir back on the Brewer and

replace the Lid. (If there is no water in the Water Reservoir, simply refill.)

2. Be sure the Brewer is turned on. Raise and lower the Handle on the

Brewer without inserting a K-Cup.

3. The LCD Control Center will display “READY TO BREW.” Brew a Large

Mug (9.25 oz. serving) of water (do not use a K-Cup).

4. Repeat steps 2 and 3 two more times to completely purge water from

inner tank.

If you are experiencing any problems with your Brewer, please contact

Customer Service at 1.866.901.BREW (2739).

ME NU

BR EW

ME NU

ADD

WATER

READY

NOT

fig.

10 11

SECTION 2 Controls & Indicators (LCD Control Center)

Setting the Clock

Setting the clock is optional. When the clock is set, the time will appear in

the LCD Control Center. NOTE: You must set the clock if you will be using the

Auto On/Off Time programming feature.

Press the MENU Button.

2. The word ‘OFF’ will appear at the top of the

LCD Control Center to indicate that the

clock is not set (fig. 10). The programming

options will appear on the LCD Control

Center with a small arrow pointing to ‘SET

CLOCK’. “H” (Hour) will appear above the

Left Button and “M” (Minute) will appear

above the Right Button. The “H” and “M”

icons and Left and Right Buttons will flash.

3. Press or hold the Left Button under the

flashing “H” until you have reached the

appropriate hour. If the hour has passed 12

“PM” will be shown.

4. Press or hold the Right Button under the

flashing “M” to set the minutes.

5. When you have reached the correct time, press the MENU Button five

times to scroll through the remaining programming steps.

BREW TEMP

Set

Hours

Set

Minutes

MEN U

BRE W

MEN U

SET CLOCK

AUTO OFF

ONOFF TIME

BREW SIZE

READY

NOT

fig.

6. The correct time should now be displayed in the LCD Control Center.

NOTE: If power is interrupted to the Brewer by unplugging it, or if power

is lost, follow the procedure above to reset the time as the clock will not be

visible until the time is set. Brew size setting is remembered and restored

automatically. All other settings will be restored automatically after clock

is set.

Programming On/Off Features

The Brewer provides three modes so that you can enjoy gourmet coffee, tea

or hot cocoa on your own schedule. By programming your Brewer to turn on

each morning, you will never have to wait for the Brewer to warm up to brew

a gourmet cup of coffee. It will take the Brewer approximately 4 minutes to

warm up from room temperate.

1. Leave it ON all the time. The Brewer can be left on all the time so that it is

always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To

turn the Brewer off at any time, simply press and release the Power Switch.

(NOTE

Although the clock remains on, if set, you can not brew a cup of coffee,

tea or hot cocoa.)

Press and release the Power Switch again to restore

power to the Brewer. You will have to wait for the water to heat up before

the Brewer is ready to brew.

2. Set the Brewer to “AUTO OFF” following a specified period of time after the

last brew.

a. Press the MENU Button twice to program the Auto Off feature. The LCD

Control Center will now display the programming options with a small

arrow next to “SET AUTO OFF” (fig. 11).

10 11

b. Press or hold the Left Button under the

blinking “H” to advance 1 hour at a time, up

to 9 hours.

c. After setting the desired Auto Off time, press

the MENU Button four times to scroll through

the remaining programming options and exit

the programming mode. “AUTO OFF SET”

(fig. 12) will now be displayed to indicate that it

has been set.

d. To cancel the Auto Off feature, press the

MENU Button twice to reach the “AUTO OFF”

programming mode. Press and release the

blue Left Button under the blinking “H”

to advance one hour at a time until “OFF”

is displayed.

3. Program your Brewer for a specific On/Off Time.

NOTE: To use this programming feature, the

clock must be set to the correct time. The clock

will not be displayed unless the time is set.

a. After setting the correct time (required), press

the MENU Button three times to program

On Time feature. The LCD Control Center will

show the programming options with a small

arrow next to “SET ON TIME” (fig. 13).

b. Press or hold the Left Button under the “H”

to scroll through the hours to your desired On

Time hour.

c. Press or hold the Right Button under the

“M” to scroll through the minutes to your

desired “ON TIME” minutes.

d. After setting the desired time, press the

MENU Button to save the “ON TIME” and

move to the “SET OFF TIME” (fig. 14).

e. If you want to set an “OFF TIME”, repeat the

procedure above in steps b & c to set your

desired “OFF TIME” (fig. 14).

f. To complete the process, press the MENU

Button two more times to exit the program-

ming mode. The Control Center will now

indicate the options you have set.

g. The Auto On time and Auto Off time functions

operate independently from one another. To

cancel either set function, follow the steps

above and use the “H” and “M” Buttons to

advance to 12:00 AM. Make sure the “M”

Button is set to :00, then change the “H”

Button. When you reach 12:00 AM, the

Control Center will display ‘OFF’ and the

function will be disabled.

EXAMPLE

If you chose to set the “On Time”

at 6:55 AM and the “Off Time” for 10:00 PM,

then the Brewer will be “READY TO BREW”

and maintain hot water in the tank during that

time so that it is always ready for you to brew.

If you wanted to brew outside this window,

BREW TEMP

Set

Hours

MEN U

BRE W

MEN U

CLOCK

SET AUTO OFF

ONOFF TIME

BREW SIZE

READY

NOT

fig.

ME N U

BR E W

ME N U

AUTO OFF SET

READY

TO BREW

fig.

BREW TEMP

Set

Hours

Set

Minutes

MEN U

BRE W

MEN U

CLOCK

AUTO OFF

SET ON TIME

BREW SIZE

READY

NOT

fig.

BREW TEMP

Set

Hours

Set

Minutes

MEN U

BRE W

MEN U

CLOCK

AUTO OFF

SET OFF TIME

BREW SIZE

READY

NOT

fig.

simply press the Power Button and you can

brew as soon as the water is heated and the

“READY TO BREW” indicator is displayed on

the LCD Control Center.

NOTE

The “On Time” and “Off Time” functions

operate independently from one another. To

cancel either function, follow the steps above

and use the “H” and “M” Buttons to advance to

12:00 AM. When you reach 12:00 AM,

the Control Center will display ‘OFF’ and the

function will be disabled (fig. 15).

NOTE: The “Auto Off Timer” and the

“On/Off Time” programming options operate

independently, but can also be programmed

to work together. For example, you can set the

On Time function to turn on at 7:00 AM and then

set the Auto Off Timer function to turn off the

Brewer two hours after the last brew.

SECTION 2 Controls & Indicators (LCD Control Center)

BREW TEMP

Set

Hours

Set

Minutes

MEN U

BRE W

MEN U

CLOCK

AUTO OFF

SET OFF TIME

BREW SIZE

READY

NOT

fig.

Programming Your Brew Size

The Brewer is preset with the Small Mug (7.25 oz.) as the default brew size.

The default brew size allows the user to avoid scrolling through brew sizes if

a particular size is chosen most often.

To change the default brew size to your

desired brew size:

1. Press the MENU Button five times.

2. Using Left and Right Buttons, select your

desired default brew size (fig. 16).

3. Once the desired default brew size is

selected press the MENU Button once to

exit. The LCD will display the brew size set.

MEN U

BRE W

MEN U

READY

TO BREW

fig.

SECTION 3 Cleaning & Maintenance

Cleaning External Parts

Regular cleaning of the Brewer’s external components is recommended.

1. Never immerse the Brewer in water or other liquids. The Housing

and other external components may be cleaned with a soapy, damp,

non-abrasive cloth.

2. The Drip Tray can accumulate up to 12 ounces of overflow. The Drip Tray

and Drip Tray Plate should be periodically inspected and rinsed clean.

To remove the Drip Tray Assembly, simply slide it toward you, keeping it

level at all times to avoid spilling. The Drip Tray and Drip Tray Plate are

dishwasher safe.

Cleaning the K-Cup Holder Assembly

1. Cleaning the Parts —The K-Cup Holder

Assembly can be placed onto the top shelf of

a dishwasher. NOTE: Use low temperature

cycles in the dishwasher.

To remove from the

Brewer, open the Lid by lifting the Handle.

Grasp the top of the K-Cup Holder with one

hand while pushing up on the bottom of the

K-Cup

Holder from underneath with the

other until it releases (fig. 17). After cleaning,

align the K-Cup Holder with the opening using

the two front ribs as a guide, and snap into

place from the top.

2. Cleaning the Funnel —The Funnel can be

removed from the K-Cup

Holder by pulling

on it until it pops off (fig. 18). The Funnel is

dishwasher safe. To replace it, just snap it

back onto the K-Cup Holder Assembly.

3. Cleaning the Exit Needle —The Exit Needle is

located on the inside bottom of the K-Cup

Holder Assembly. Should a clog arise due to

coffee grinds, it can be cleaned using a paper

clip or similar tool. Remove K-Cup Holder

assembly and detach Funnel. Insert the paper

clip (as shown in fig. 18) into the Needle to

loosen the clog and push it out. The K-Cup

Holder is dishwasher safe.

CAUTION: There are sharp needles that puncture the K-Cup above the K-Cup

Holder and in the bottom of the K-Cup Holder. To avoid risk of injury, do not

put your fingers in the K-Cup Assembly Housing.

Cleaning the Water Reservoir & Water Reservoir Lid

The Water Reservoir Lid or Water Reservoir should not be put into the

dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth

and rinsed thoroughly. Do not dry the inside of the Water Reservoir with a

cloth as lint may remain.

CAUTION: Please rinse the Water Reservoir thoroughly after cleaning to ensure

that no cleaners or cleaning solutions remain in this area as they may contaminate

the water supply in the Brewer.

fig.

De-Scaling Your Brewer

Mineral content in water varies from place to place. Depending on the mineral

content of the water in your area, calcium deposits or scale may build up in

your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer

performance. De-scaling your Brewer helps maintain the heating element

and other internal parts of the Brewer that come in contact with water.

The Brewer should be de-scaled every 3-6

months to ensure optimal performance. It is

possible for calcium deposits to build up faster,

making it necessary to de-scale more often.

This Brewer is equipped to detect when scale

buildup is interfering with the performance of

the Brewer. When this is detected, “DE-SCALE”

will be displayed on the LCD Control Center

(fig. 19). However, even if “DE-SCALE” is not

displayed, you should continue to de-scale your

Brewer every 3-6 months.

SECTION 3 Cleaning & Maintenance (continued)

You should promptly de-scale if “DE-SCALE” is displayed on the LCD Control

Center. Properly follow the de-scaling procedure described.

NOTE: The Brewer will continue to function even when “DE-SCALE” is displayed.

However, if you do not de-scale soon after it is displayed, continued scale

build-up could damage the Brewer. If this occurs, “DE-SCALE” will begin to blink to

alert you to the potential damage to the Brewer if you do not de-scale immediately.

De-Scaling Instructions

A. PREPARE

Step 1: Make sure you have at least 48 ounces of undiluted white vinegar

on hand. You will also need an empty sink and a large ceramic mug

(do not use a paper cup).

Step 2: Empty the water in the Water Reservoir.

Step 3: Disable “Auto-Off” features.

B. FILL AND CLEAN

Step 1: Pour the vinegar into the Water Reservoir and fill it.

Step 2: Place a large mug on the Drip Tray Plate and run a water brew cycle.

DO NOT USE A K-CUP, just select the Large Mug brew size. Pour the

contents of the large mug into the sink.

ME N U

BR E W

ME N U

DE-SCALE

READY

TO BRE W

fig.

Step 3: Repeat the brew process 3 times.

Step 4: Now let the Brewer stand for at least 4 hours while still on.

C. RINSE

Step 1: Ensure the Water Reservoir is filled with fresh water.

Step 2: Place a large mug on the Drip Tray Plate and run a water brew cycle.

Pour the contents of the large mug into the sink.

Step 3: Repeat brew process until the Water Reservoir is empty.

Step 4: You may need to perform additional water brew cycles if you notice

any residual taste.

NOTE: If “DE-SCALE” is still displayed on the LCD Control Center after

completing the procedure, repeat the de-scaling procedure above.

Service

Beyond these recommended cleaning and maintenance procedures this

Brewer is not user serviceable. For service, please refer to the Warranty

section of this guide.

Storage

Empty the Water Reservoir before storing, and take care to ensure that you

store your Brewer in a safe and frost free environment. Please be sure to

store your Brewer in its upright position to avoid water leakage from the inner

tank. If you store the Brewer in a cold environment, you run the risk of water

freezing inside the Brewer and causing damage. When you prepare to use it

after storage, we recommend rinsing the Water Reservoir with fresh water

and running three cleansing brews without a K-Cup.

If you plan to move your Brewer to a different location, turn the Brewer

off, unplug it, and empty the Water Reservoir. If your Brewer has been in

an environment below freezing, please be sure to let it warm to room

temperature for at least 2 hours before using.

SECTION 4 Troubleshooting

Situation

Brewer does not

have power

Brewer will not brew

Solution

• Plug Brewer into an independent outlet.

• Check to be sure that it is plugged in securely.

• Plug into a different outlet.

• Reset your home’s circuit breaker if necessary.

• Make sure that the Power Switch has been

turned on and LCD lights are illuminated.

• After placing the K-Cup

in the K-Cup Holder, make

sure the Handle is pushed down securely and the

LCD Control Center reads ‘READY TO BREW’ with

the Left, Right and BREW Buttons flashing, then

press the Left, Right or BREW Button.

• If the LCD Control Center indicates “ADD

WATER”, add water to the Water Reservoir or

make sure the Water Reservoir is seated

properly in its base.

• If the LCD Control Center indicates “ADD WATER”

even after refilling, contact Customer Service at

1.866.901.BREW (2739).

• The Exit Needle may be clogged (refer to page 13).

Situation

Brewing a partial cup

The time is not

displayed on the LCD

Message Center

Brewer shuts

off or turns on

automatically

The blue light in Water

Reservoir is flashing

Solution

• The Exit Needle may be clogged (refer to page 13).

• Clean the K-Cup Holder if necessary and rinse

under faucet (refer to page 13).

• The Water Reservoir may have been removed

during brewing. Replace the Water Reservoir

and perform a water brew without a K-Cup.

• “De-Scale” the Brewer (refer to page 14 ).

• If you have repeated the de-scale procedure on

your Brewer two times and it is still only brewing

a partial cup, contact Customer Service at

1.866.901.BREW (2739).

• The time will not be displayed on the LCD

unless you have set it. To set the clock, follow

the procedure on page 10.

• If power is interrupted to the Brewer, you will

need to set the clock again using the procedure

on page 10.

• Check to make sure that the Auto Off Timer

and/or On/Off Time features have not been set.

To do this, press the MENU Button below

“MENU” and scroll through the programming

options. “OFF” should be displayed for Auto Off

Timer and On/Off. If “OFF” is not displayed,

follow directions on page 10 to reset.

• The water level is low and a full cup cannot be

brewed. Add water to Water Reservoir

If any problems persist, contact Customer Service at 1.866.901.BREW (2739)

SECTION 5 Warranty

Limited One Year Warranty

Keurig

warrants that your Brewer will be free of defects in materials or

workmanship under normal home use for one year from the date of purchase.

It is recommended that you fill out and return the warranty card enclosed

with your Brewer so that your purchase information will be stored in our

system. Keurig will, at its option, repair or replace the Brewer without charge

upon its receipt of proof of the date of purchase. If a replacement Brewer is

necessary to service this warranty, the replacement Brewer may be new or

reconditioned. If a replacement Brewer is sent, a new limited one year

warranty will be applied to the replacement Brewer.

This warranty only applies to Brewers operated in the United States and

Canada. This warranty gives you specific legal rights, and you may also have

other rights that vary from state to state and, in the case of Canada, from

province to province.

What is not covered by the Limited Warranty?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL

DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER

INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH

OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces

do not allow the exclusion or limitations of incidental or consequential

damages, so the above limitation or exclusion may not apply to you

depending on the state or province of purchase.

Nor does this warranty cover damages caused by services performed by

anyone other than Keurig or its authorized service providers, use of parts

other than genuine Keurig parts, or external causes such as abuse, misuse,

inappropriate power supply or acts of God.

Other Limitations

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS

WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY

SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO

YOUR B77 BREWER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT

ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or

provinces do not allow disclaimers of such implied warranties or limitations

on how long an implied warranty lasts, so the above limitation may not apply

to you depending on the state or the province of purchase.

How do you obtain warranty service?

Keurig Brewers are high-quality appliances and, with proper care, are

intended to provide years of satisfying performance. However, should the

need arise for warranty servicing, simply call Keurig Customer Service at

our toll free phone number 1.866.901.BREW (2739). Please do not return your

Brewer for servicing without first speaking to Keurig Customer Service to

obtain an Authorization to Return number (ATR). Keurig Brewers returned

without an ATR number will be returned to the sender without servicing.

Keurig, Incorporated

55 Walkers Brook Drive

Reading, MA 01867

1.866.901.BREW (2739)

Lors de l’utilisation de tout appareil électrique, des

mesures de sécurité de base devraient être suivies,

et notamment :

1. Lire toutes les instructions avant l’utilisation.

2. Ne pas toucher les surfaces chaudes. Utiliser les

poignées s’il y en a.

3. Installer correctement l’appareil et le placer dans

un endroit conforme aux présentes instructions

avant de l’utiliser.

4. L’utilisation d’accessoires non recommandés par

le fabricant de l’appareil risque de causer des

incendies, des chocs électriques ou des blessures.

5. Éviter le contact ou la proximité de l’appareil avec

un élément électrique ou un brûleur à gaz. Éviter

également de placer l’appareil à l’intérieur d’un

four chaud.

6. Ne pas utiliser à l’extérieur.

7. Pour éviter les risques d’incendie, de chocs élec-

triques ou de blessures, ne pas immerger la fiche,

le cordon d’alimentation ou l’appareil dans l’eau ni

dans aucun autre liquide.

8. Ne pas trop remplir le réservoir d’eau.

9. Utiliser seulement de l’eau dans cet appareil!

Ne verser aucun autre liquide ou aliment dans

le réservoir d’eau à l’exception des produits

mentionnés dans les instructions de nettoyage

du présent manuel.

10. Éteindre et débrancher l’appareil avant de le net-

toyer ou d’en faire l’entretien. Laisser l’appareil

refroidir avant d’ajouter ou d’enlever des pièces et

avant de le nettoyer.

11. Pour une utilisation optimale, brancher l’appareil

dans une prise de courant séparée sur un circuit

spécialisé pour éviter que les lumières vacillent,

que les fusibles sautent ou que les disjoncteurs

se déclenchent.

12. Ne jamais utiliser un appareil dont la fiche ou le

cordon d’alimentation est endommagé ou un ap-

pareil qui présente un trouble de fonctionnement

ou qui a été endommagé. Communiquer avec le

Service à la clientèle de Keurig pour signaler tout

mauvais fonctionnement de la cafetière ou tout

dommage à celle-ci.

13. Ne pas laisser le cordon d’alimentation pendre

d’une table ou d’un comptoir ni entrer en contact

avec une surface chaude.

14. Pour débrancher la cafetière, appuyer sur le

bouton de mise en marche situé à l’arrière de la

cafetière pour le mettre en position « OFF », puis

retirer le cordon de la prise.

15. Ne jamais laisser des enfants utiliser la cafetière

ni rester à proximité sans surveillance.

16. Ne pas soulever la poignée de la cafetière pen-

dant une infusion.

17. Toujours laisser le couvercle sur le réservoir

d’eau, sauf lors du remplissage.

18. L’appareil est équipé d’un cordon d’alimentation

muni d’un fil et d’une prise de mise à la terre.

L’appareil doit être mis à la terre en utilisant une

prise de courant à contact de mise à la terre à

trois trous. En cas de court-circuit, la mise à la

terre réduit les risques de chocs électriques.

19. Si la prise de courant est une prise de courant

murale standard à deux trous, le propriétaire a

l’obligation et la responsabilité de la faire rem-

placer par une prise de courant de mise à la terre

à trois trous.

20. Il ne faut en aucun cas couper ou enlever la

troisième broche (mise à la terre) de la fiche du

cordon d’alimentation, ni utiliser un adaptateur.

21. Consulter un électricien qualifié si les instruc-

tions sur la mise à la terre ne sont pas parfaite-

ment comprises ou en cas de doutes sur la mise à

la terre de l’appareil.

22. Ne pas utiliser l’appareil pour une fin autre que

celle pour laquelle il a été conçu.

CONSERVER CE MANUEL.

RÈGLES DE SÉCURITÉ IMPORTANTES

Fonctionnement et utilisation sans danger

AVERTISSEMENT AUX UTILISATEURS ET AUX PARENTS

1. NE permettez PAS aux enfants d’utiliser l’appareil sans

la supervision d’un adulte. L’appareil distribue de l’eau

très chaude.

2. AVIS SPÉCIAL AUX UTILISATEURS DE CHOCOLAT

CHAUD : APRÈS L’UTILISATION D’UN GODET K-CUP DE

CHOCOLAT CHAUD, LANCEZ IMMÉDIATEMENT un cycle

d’infusion d’eau chaude sans K-Cup pour éviter une

possible obstruction de l’aiguille de sortie. NE tenez

PAS pour acquis que le prochain utilisateur le fera.

ATTENTION : Le godet K-Cup

est perforé par deux aiguilles, une au-dessus

du support à K-Cup et l’autre au fond du support à K-Cup. Pour éviter tout risque

de blessure, ne pas mettre les doigts dans le boîtier du support à K-Cup.

ATTENTION : L’eau se trouvant dans le support à K-Cup durant l’infusion est

extrêmement chaude. Pour éviter tout risque de blessure, ne pas soulever la

poignée ni ouvrir le boîtier du support à K-Cup durant l’infusion.

INSTRUCTIONS POUR CORDON D’ALIMENTATION COURT :

L’appareil est doté

d’un cordon d’alimentation court pour éviter qu’il s’emmêle ou que quelqu’un

trébuche sur un cordon long.

Si une rallonge est utilisée, (1) les caractéristiques électriques inscrites sur

la rallonge doivent égaler ou excéder celles de l’appareil, (2) le cordon doit

être fixé de façon à ce qu’il ne pende pas d’une table ou d’un comptoir pour

éviter qu’un enfant puisse le saisir ou que quelqu’un trébuche et (3) la ral-

longe doit être munie d’une prise de mise à la terre à trois broches.

CE PRODUIT EST DESTINÉ À UNE UTILISATION DOMESTIQUE SEULEMENT.

AVERTISSEMENT CE PRODUIT CONTIENT DES PRODUITS

CHIMIQUES, NOTAMMENT DU PLOMB, UN MÉTAL QUI, SELON L’ÉTAT DE

LA CALIFORNIE, CAUSE LE CANCER, DES ANOMALIES CONGÉNITALES OU

D’AUTRES MALFORMATIONS GÉNÉTIQUES.

TABLE DES MATIÈRES

SYSTÈME D’INFUSION GOURMET

UNE TASSE À LA FOIS DE KEURIG

Select B77 — Comment utiliser votre cafetière

RÉGLAGES

Conseils utiles ...................................................................................20

Déballage ...........................................................................................20

Caractéristiques ...............................................................................21

SECTION 1 — RÉGLAGES ET PREMIÈRE INFUSION

Préparation et première infusion ...................................................22

SECTION 2 — COMMANDES ET VOYANTS

Réglage de l’horloge ........................................................................26

Programmation des fonctions de mise

en marche et d’arrêt automatiques ...............................................26

Programmation du format de tasse ..............................................28

SECTION 3 — NETTOYAGE ET ENTRETIEN

Nettoyage ...........................................................................................29

Détartrage .........................................................................................30

Entreposage .......................................................................................31

SECTION 4 — DÉPANNAGE ...............................................................32

SECTION 5 — GARANTIE ..................................................................33

Inscrivez le numéro de série de votre cafetière ici.

AVERTISSEMENT

AVERTISSEMENT : POUR RÉDUIRE LES RISQUES

D’INCENDIE ET DE CHOCS ÉLECTRIQUES, NE PAS RETIRER

LE COUVERCLE INFÉRIEUR. CET APPAREIL NE CONTIENT

AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR. LES

RÉPARATIONS NE DEVRAIENT ÊTRE EFFECTUÉES QUE

PAR UN TECHNICIEN DE SERVICE AGRÉÉ.

Le retrait de l’étiquette du numéro de série annulera la garantie.

RISQUE D’INCENDIE ET DE

CHOCS ÉLECTRIQUES

NE PAS OUVRIR!

Réglages

Conseils utiles

1. Laissez votre cafetière allumée en tout temps.

Nous vous suggérons de toujours laisser votre

cafetière allumée. Vous pourrez ainsi savourer

une tasse de café, de thé ou de chocolat chaud

fraîchement infusé à tout moment. Toutefois,

la cafetière est entièrement programmable, ce

qui vous permet de la mettre en marche ou de

l’arrêter aux moments qui vous conviennent. Si

vous préférez, vous pouvez également régler

la cafetière pour qu’elle s’arrête après une

certaine période de temps. Veuillez consulter

les instructions des pages 26-28 pour que le ré-

glage de votre cafetière réponde à vos besoins.

2. Pour obtenir le meilleur café gourmet, thé de spé-

cialité ou chocolat chaud possible, Keurig recom-

mande l’utilisation d’eau embouteillée ou filtrée.

La qualité de l’eau varie d’un endroit à l’autre.

Si votre café a un goût désagréable de chlore

ou de minéraux, nous vous recommandons

d’utiliser de l’eau embouteillée ou de l’eau

filtrée à l’aide d’un système de filtration d’eau.

3. Choisissez le format, la saveur et l’infusion que

vous aimez.

Avec plus de 200 variétés de K-Cups et quatre

formats d’infusion : boisson glacée de 96 ml

(3,25 oz), petite tasse de 155 ml (5,25 oz), tasse

moyenne de 214 ml (7,25 oz), et grande tasse

de 274 ml (9,25 oz), votre cafetière Keurig

vous

offre d’infinies possibilités de formats,

de saveurs et d’infusions pour préparer la bois-

son idéale pour vous. Pour une boisson forte au

goût plus prononcé, choisissez une K-Cup

très

intense, qui contient 30 % plus de café que nos

cafés ordinaires, et le format d’infusion qui vous

convient. Plus le format d’infusion est petit, plus

la saveur sera forte. Plus le format d’infusion est

grand, plus la saveur sera douce.

4. Branchez la cafetière sur un circuit avec mise à

la terre où elle seule est branchée.

Une surcharge du circuit électrique avec

plusieurs appareils risque de nuire au fonc-

tionnement de votre cafetière. Celle-ci devrait

être branchée séparément des autres appa-

reils, sur son propre circuit électrique.

5. Infusez votre café dans une tasse de voyage.

Pour infuser un café dans une tasse de voyage,

vous n’avez qu’à retirer la cuvette d’égouttage

et à placer la tasse de voyage sur la base de la

cuvette.

6. Détartrez régulièrement la cafetière.

Voir les instructions aux pages 30 et 31.

Déballage de la cafetière

1. Placez la boîte de la cafetière sur une grande

surface plane, comme une table ou un comp-

toir, ou sur le plancher. Ouvrez la boîte.

2. Enlevez la documentation fournie.

3. Couchez l’emballage sur le côté, la partie avant

de la boîte en dessous.

4. Saisissez le sac de plastique contenant la

cafetière.

5. Tirez soigneusement le sac de plastique (et le

matériel d’emballage) vers vous pour le sortir

de la boîte. La cafetière est encastrée dans le

polymousse et repose sur le côté.

6. Retirez la partie supérieure du polymousse.

7. Retirez soigneusement la cafetière de la base

de polymousse et placez-la debout sur une

surface plane et stable.

8. Enlevez le sac de plastique de la cafetière.

9. Inscrivez le numéro de série de la cafetière à

la page 19 de ce manuel. Le numéro de série

est indiqué sous la boîte de la cafetière, de

même que sur la cafetière, derrière la cuvette

d’égouttage (visible quand on retire la cuvette).

10. Placez la cafetière debout sur une surface

plane et stable. Enlevez le ruban adhésif qui

maintient le réservoir d’eau en place.

Nous vous recommandons de conserver tout le

matériel d’emballage au cas où il serait néces-

saire de retourner la cafetière.

AVERTISSEMENT :

Gardez tous les sacs de plastique

hors de la portée des enfants.

La page charge ...

Keurig Select B77 Le manuel du propriétaire

Marque: Keurig

Modèle: Select B77

Catégorie: Accessoires de préparation de café

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Keurig Select B77 Owner's manual

Keurig Select B77 Le manuel du propriétaire

Keurig Select B77 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents