GE PSS25MGNWW Manuel utilisateur

GEAppliances.com
Refrigerators
Profile Side by Side
200D2600P015      49-60185     11-01 JR
La section française commence à la page 40
La sección en español empieza en la página 74
Safety Instructions  . . . . . . . . . . .2–4
Operating Instructions
Additional Features  . . . . . . . . . . . .10
Automatic Icemaker  . . . . . . . . . . .12
Care and Cleaning . . . . . . . . . .14, 15
Crispers and Pans  . . . . . . . . . . . . .11
Ice and Water Dispenser  . . . . .13, 14
Refrigerator Doors  . . . . . . . . . . . .10
Replacing the Light Bulbs . . . . . . .16
Shelves and Bins  . . . . . . . . . . . . .8, 9
Temperature Controls . . . . . . . . . . .5
TurboCool
™
 . . . . . . . . . . . . . . . . . . .6
Water Filter  . . . . . . . . . . . . . . . . . . .7
Installation Instructions
Preparing to Install 
the Refrigerator  . . . . . . . . . . . .22, 23
Removing and Replacing Doors  . .21
Trim Kits and Panels  . . . . . . . .17–20
Water Line Installation  . . . . . .24–28
Troubleshooting Tips  . . . . . . .30–32
Normal Operating Sounds  . . . . . .29
Consumer Support
Consumer Support  . . . . .Back Cover
Performance Data Sheet  . . . . . . . .36
Product Registration  . . . . . . . .33, 34
State of California Water 
Treatment Device Certificate . . . . .37
Warranty (Canadian) . . . . . . . . . . .38
Warranty (U.S.)  . . . . . . . . . . . . . . .39
Réfrigérateurs
Profile Côte à Côte
Refrigeradores
Profile Lado a Lado
Models 23, 25, 27 and 29
Write the model and serial numbers here:
# ________________________________
# ________________________________
Find these numbers on a label inside 
the refrigerator compartment at the 
top on the right side.
Owner’s Manual 
and Installation
Manuel d’utilisation 
et d’installation
Manual del propietario 
e instalación

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating

element located on the bottom of the icemaker.

Do not place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■Setting either or both controls to

0 (off)

does not

remove power to the light circuit.

■

■Do not refreeze frozen foods which have

thawed completely.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

GEAppliances.com

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may

not easily climb inside.

CFC Disposal

Your old refrigerator may have a cooling system

that used CFCs (chlorofluorocarbons). CFCs are

believed to harm stratospheric ozone.

If you are throwing away your old refrigerator, make

sure the CFC refrigerant is removed for proper

disposal by a qualified servicer. If you intentionally

release this CFC refrigerant, you can be subject to

fines and imprisonment under provisions of

environmental legislation.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

3

4

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

If the outlet is a standard 2-prong outlet, it is

your personal responsibility and obligation to

have it replaced with a properly grounded

3-prong wall outlet.

The refrigerator should always be plugged into

its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on

the power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS

(Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a

temporary connection

may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks,

DO NOT

USE

the refrigerator until a proper ground has

been established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to

make sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

5

About the temperature controls.

GEAppliances.com

WARMERCOLDER

ADJUST REFRIGERATOR TEMP

9 IS COLDEST

WARMERCOLDER

ADJUST FREEZER TEMP

9 IS COLDEST

The temperature controls are preset in the factory at 5 for both

the refrigerator and freezer compartments. Allow 24 hours for the

temperature to stabilize to the preset recommended settings.

Several adjustments may be required. Each time you adjust

controls, allow 24 hours for the refrigerator to reach the setting

you have selected.

Setting either or both controls to 0 stops cooling in both the freezer

and refrigerator compartments, but does not shut off electrical power

to the refrigerator.

Control settings will vary based on personal preferences, usage and

operating conditions and may require more than one adjustment.

NOTE: The refrigerator is shipped with protective film covering the

temperature controls. If this film was not removed during installation,

remove it now.

The Performance Air Flow System is designed to maximize temperature control in the refrigerator and

freezer compartments. This unique special feature consists of the Air Tower along the back wall of the

refrigerator and the Air Tunnel on the bottom portion of the freezer rear wall. Placing food in front of the

louvers on these components will not affect performance. Although the Air Tower and the Air Tunnel can

be removed, doing so will affect temperature performance. (For removal instructions, on-line, 24 hours a

day, contact us at GEAppliances.com or call 800.GE.CARES. In Canada, contact us at geappliances.ca or

call 1.800.361.3400.)

Performance Air Flow System

6

About TurboCool.

™

How it Works

TurboCool

rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use

TurboCool

when adding a

large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until

the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle

on and off to maintain this setting. After 8

hours, or if

TurboCool

is pressed again, the

refrigerator compartment will return to

the original setting.

How to Use

Press

TurboCool

. The refrigerator

temperature display will show

9

(the coldest

setting).

After

TurboCool

is complete, the

refrigerator compartment will return

to the original setting.

NOTES:

The refrigerator temperature

cannot be changed during

TurboCool

.

The freezer temperature is not

affected during

TurboCool

.

When opening the refrigerator

door during

TurboCool

, the fans

will continue to run if they have

cycled on.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

7

About the water filter.

(on some models)

GEAppliances.com

On some models

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

There is a replacement indicator light for

the water filter cartridge on the dispenser.

This light will turn orange to tell you that

you need to replace the filter soon.

The filter cartridge should be replaced

when the replacement indicator light turns

red or if the flow of water to the dispenser

or icemaker decreases.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one by slowly turning

it to the left.

Do not

pull down on the

cartridge. A small amount of water

may drip down.

Fill the replacement cartridge with

water from the tap to allow for better

flow from the dispenser immediately

after installation.

Lining up the arrow on the cartridge

and the cartridge holder, place the

top of the new cartridge up inside

the holder.

Do not

push it up into

the holder.

Slowly turn it to the right until the filter

cartridge stops.

DO NOT OVERTIGHTEN.

As you turn the cartridge, it will

automatically raise itself into position.

Cartridge will rotate about 1/4 turn.

Run water from the dispenser for

3 minutes (about one and a half

gallons) to clear the system and

prevent sputtering.

Press and hold the

RESET WATER FILTER

pad on the dispenser for 3 seconds.

NOTE:

A newly-installed water filter

cartridge may

cause water to spurt

from

the dispenser.

Filter Bypass Plug

You must use the filter bypass plug

when a replacement filter cartridge is not

available. The dispenser and the icemaker

will not operate without the filter or filter

bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call GE Parts

and Accessories, 800.626.2002.

GWF

Suggested Retail $34.95 USD

Customers in Canada should consult

the yellow pages for the nearest Camco

Service Center.

Place the top of the cartridge up

inside the cartridge holder and

slowly turn it to the right.

Filter Bypass Plug

Cartridge

Holder

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

8

About the shelves and bins.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and

freezer tilt-out door bins are adjustable.

To remove:

Lift the front of the bin straight

up, then lift up and out.

To replace or relocate:

Engage the back side

of the bin in the molded supports of the

door. Then push down on the front of the

bin. Bin will lock in place.

Small Bins

To remove:

Lift the front of the bin straight

up then out.

To replace:

Position the bin above the

rectangular molded supports on the door.

Then slide the bin down onto the support

to lock it in place.

The snugger

helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Place a finger on either side of the

snugger near the rear and move it back

and forth to fit your needs.

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

9

GEAppliances.com

Not all features are on all models.

QuickSpace

™

Shelf

This shelf splits in half and slides under

itself for storage of tall items on the shelf

below.

This shelf can be removed and replaced

or relocated just like Slide-Out Spillproof

Shelves.

On some models, this shelf can not be used

in the lowest position.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the

shelf straight out.

To replace or relocate:

Line the shelf up with the supports and

slide it into place. The shelf can be

repositioned when the door is at 90° or

more. To reposition the shelf, slide the shelf

past the stops and angle downward. Slide

shelf down to the desired position, line up

with the supports and slide into place.

Make sure you push the shelves all the way back

in before you close the door.

Slide-Out Freezer Shelves

To remove,

slide out to the

stop

position,

lift the front past the stop position, and

slide out.

Make sure you push the shelves all the way back

in before you close the door.

Freezer Baskets

To remove,

slide out to the

stop

position,

lift the front past the stop position, and

slide out.

Make sure you push the baskets all the way back

in before you close the door.

Press tab and pull shelf

forward to remove

Fixed Freezer Shelves

To remove,

lift the shelf up at the left side

and then bring the shelf out.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

10

About the additional features.

Not all features are on all models.

Removable Beverage Rack

The beverage rack is designed to hold

a bottle on its side. It can be attached

to any slide-out shelf.

To install:

Line up the large part of the slots on

the top of the rack with the tabs under

the shelf.

Then slide the rack back to lock it

in place.

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different

than the ones you are used to. The special

door opening/closing feature makes sure

the doors close all the way and are securely

sealed.

When opening and closing the door you

will notice a

stop

position. If the door is

opened past this

stop

point, the door will

remain open to allow you to load and

unload food more easily. When the door

is only partially open, it will automatically

close.

The resistance you feel at the

stop

position will be reduced as the door

is loaded with food.

When the door is only partially open,

it will automatically close.

Beyond this stop the door will

stay open.

1

2

Door Alignment

If doors are uneven, adjust the refrigerator

door.

Using a 7/16″ socket wrench, turn the

door adjusting screw to the right to

raise the door, to the left to lower it.

(A nylon plug, imbedded in the

threads of the pin, prevents the pin

from turning unless a wrench is used.)

After one or two turns of the wrench,

open and close the refrigerator door

and check the alignment at the top of

the doors.

To remove the base

grille, open the doors,

remove the screw at

each end of the base

grille and then pull

the grille straight out.

7/16″Socket Wrench

Raise

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling

the drawer straight out and lifting the

drawer up and over the

stop

location.

If the door prevents you from taking out

the drawers, first try to remove the door

bins. If this does not offer enough

clearance, the refrigerator will need to

be rolled forward until the door opens

enough to slide the drawers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator

to the left or right as you roll it out.

11

About the crispers and pans.

GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers should be wiped dry.

On some models,

the bottom drawer has

a cover that slides back as the drawer is

opened. This allows full access to the

drawer. As the drawer is closed, the cover

will slide forward into its original position.

Adjustable Humidity Crispers

Slide the control all the way to the

HI

setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the

LO

setting to provide lower humidity

levels recommended for most fruits.

HI LO

Convertible Meat Pan

The convertible meat pan has its own

cold air duct to allow a stream of cold air

from the freezer compartment to flow to

the pan.

The variable temperature control

regulates

the air flow from the Climate Keeper.

Set the control to the

coldest

setting to store

fresh meats.

Set the control to

cold

to convert the pan

to normal refrigerator temperature and

provide extra vegetable storage space. The

cold air duct is turned off. Variable settings

between these extremes can be selected.

C

O

L

D

C

O

L

D

E

S

T

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Automatic Icemaker

The icemaker will produce seven cubes

per cycle–approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the

O (off)

position.

When the refrigerator has been connected

to the water supply, set the power switch to

the

l (on)

position.

The icemaker will fill with water when it

cools to 15°F (–10°C). A newly-installed

refrigerator may take 12 to 24 hours to

begin making ice cubes.

Throw away the first few batches of ice

to allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

About the automatic icemaker.

A newly-installed refrigerator may take 12 to 24 hours to begin making ice.

Ice Storage Drawer

To access ice,

pull the drawer forward.

To remove the drawer,

pull it straight out and

lift it past the

stop

location.

12

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Pull the upper freezer shelf straight

out to access the icemaker. Always

be sure to replace the shelf. The

shelf can be used for storage.

Ice Drawer

Shelf

Ice Drawer

About the ice and water dispenser.

(on some models)

GEAppliances.com

On some models

To Use the Dispenser

Select

CUBED ICE , CRUSHED ICE

or

WATER .

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To

reduce water spotting, the shelf and its

grille should be cleaned regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two

minutes to remove trapped air from the water

line and to fill the water system. To flush out

impurities in the water line, throw away the first

six glassfuls of water.

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

Press the

LOCK CONTROL

pad for 3 seconds to

lock the dispenser and

control panel. To

unlock, press and

hold the pad again

for 3 seconds.

Dispenser Light

This pad turns the

night

light

in the dispenser on

and off. The light also

comes on when the

dispenser cradle is

pressed. If this light

burns out, it should be

replaced with a 6 watt

12 V maximum bulb.

Quick Ice

When you need ice

in a hurry, press this

pad to speed up ice

production. This will

increase ice production

for the following

48 hours or until you

press the pad again.

Door Alarm

To set the alarm, press

this pad until the

indicator light comes

on. This alarm will

sound if either door is

open for more than

3 minutes. The light

goes out and the

beeping stops when

you close the door.

Spill Shelf

Important Facts About Your Dispenser

■Do not add ice from trays or bags to

the storage drawer. It may not crush or

dispense well.

■Avoid overfilling glass with ice and use

of narrow glasses. Backed-up ice can jam

the chute or cause the door in the chute

to freeze shut. If ice is blocking the

chute, poke it through with a wooden

spoon.

■Beverages and foods should not be

quick-chilled in the ice storage drawer.

Cans, bottles or food packages in the

storage drawer may cause the icemaker

or auger to jam.

■To keep dispensed ice from missing

the glass, put the glass close to, but not

touching, the dispenser opening.

■Some crushed ice may be dispensed even

though you selected

CUBED ICE.

This

happens occasionally when a few cubes

accidentally get directed to the crusher.

■After crushed ice is dispensed, some

water may drip from the chute.

■Sometimes a small mound of snow will

form on the door in the ice chute. This

condition is normal and usually occurs

when you have dispensed crushed ice

repeatedly. The snow will eventually

evaporate.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

13

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Care and cleaning of the refrigerator.

Cleaning the Outside

The dispenser drip area,

(on some models)

beneath the grille, should be wiped dry. Water

left in this area may leave deposits. Remove

the deposits by adding undiluted vinegar to

the well. Soak until the deposits disappear

or become loose enough to rinse away.

The dispenser cradle

(on some models).

Before cleaning, lock the dispenser by

pressing and holding the

LOCK CONTROL

pad for 3 seconds. Clean with warm

water and baking soda solution–about

a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. Rinse thoroughly

and wipe dry.

The door handles and trim.

Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a

commercially available stainless steel

cleaner such as Stainless Steel Magic.

™

Stainless Steel Magic is available at Ace, True

Value, Servistar, HWI and other leading

stores. It is also available through GE Parts

and Accessories, 800.626.2002. Order part

number WX10X15.

Do not use appliance wax or polish on the

stainless steel.

Keep the outside clean.

Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors,

leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning.

If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution–

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both cleans

and neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that

which is recommended, especially those that

contain petroleum distillates, can crack or

damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference

may cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in

the dishwasher.

Ice Storage Drawer

on Dispenser Models

To remove:

Set the icemaker power switch to the

O (off)

position. Pull the drawer straight out

and then lift past the

stop

position.

To replace:

When replacing the drawer, be sure to

press it firmly into place. If it does not go

all the way back, remove it and rotate the

drive mechanism 1/4 turn. Then push

the drawer back again.

Rotate

Drive

Mechanism

Dispenser drip area.

14

About the ice and water dispenser.

For long vacations or absences, remove

food and unplug the refrigerator. Clean

the interior with a baking soda solution

of one tablespoon (15 ml) of baking soda

to one quart (1 liter) of water. Leave the

doors open.

Set the icemaker power switch to the

O (off)

position and shut off the water supply

to the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

15

GEAppliances.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line (on some models).

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and

drawers by taping them securely in place

to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Replacing the light bulbs.

Setting either or both controls to 0 does not remove power to the light circuit.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

The bulbs are located at the top of the

compartment, inside the light shield.

On some models, a screw at the front of

the light shield will have to be removed.

To remove the light shield, press in on

the tabs on the sides of the shield and

slide forward and out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the light shield and

screws (on some models). When

replacing the light shield, make sure

that the tabs at the back of the shield fit

into the slots at the back of the light

shield housing.

Plug the refrigerator back in.

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.

Remove the convertible meat drawer

control knob by pulling straight out.

Lift the light shield up and pull it out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the shield and

the knob.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light

shield. (The shelf will be easier to

remove if it is emptied first.) On some

models, a screw at the top of the light

shield will need to be removed.

To remove the light shield, press in on

the sides, and lift up and out.

Replace the bulb with an appliance

bulb of the same or lower wattage,

and reinstall the light shield. When

reinstalling the light shield, make

sure the top tabs snap securely

into place. Replace the screw (on

some models).

Reinstall the shelf and plug the

refrigerator back in.

16

C

O

L

D

C

O

L

D

E

S

T

Dispenser

Unplug the refrigerator.

The bulb is located on the

dispenser under the control panel.

Remove the light bulb by turning

it counterclockwise.

Replace the bulb with a bulb of the

same size and wattage.

Plug the refrigerator back in.

Tabs

1/4″ (6 mm) Max.

Panels thicker than 1/4″ (6 mm)

5/16″ (8 mm)

3/4″ (19 mm)

17

Trim kits and decorator panels.

For CustomStyle

™

models

Read these instructions completely and carefully.

Before You Begin

2″(5.1 cm)

Clearance

Handle Side

Appearance

Panel

Refrigerator

Door

1/4″(6 mm)

Thick Backing

3/4″

(19 mm)

3/4

″

(19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board

can be used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm)

from the handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) maximum, will require that the outer 5/16″

(8 mm) of panel perimeter be no thicker than 1/4″ (6 mm).

Weight limitations for custom panels:

Fresh Food 38 lbs. (17 kg) max.

Freezer Door 28 lbs. (13 kg) max.

1/4″ (6 mm) Max.

Panels 1/4″ (6 mm) thick or less

Some models are equipped with trim kits that allow you to install door panels. You can order

pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,

800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4

″

(6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″

(3 mm) cardboard, that will fit between the face of the door and the wood panel. If you are installing the

pre-cut decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the

decorator or wood panel and the filler panel should be 1/4″ (6 mm).

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

18

Trim kits.

Freezer Panel

Without Dispenser

Freezer Panel

With Dispenser

Fresh Food Panel

Cut

out

5/16″

(8 mm)

14

15

⁄32″

(36.8 cm)

67

9

⁄32″

(171 cm)

1/8″

(3 mm)

FRONT

5/16″

(8 mm)

17

7

⁄8″

(45.4 cm)

14

15

⁄32″

(36.8 cm)

33

5

⁄8″

(85.4 cm)

1/8″

(3 mm)

Cut

out

FRONT

5/16″

(8 mm)

67

9

⁄32″

(171 cm)

1/8″

(3 mm)

Cut

out

19

15

⁄32″

(49.5 cm)

FRONT

Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

19

Inserting the door panels.

Read these instructions completely and carefully.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Attach the Top Trim on the Freezer and Fresh Food Doors.

The Top Trim can be found inside the refrigerator

compartment.

With a T-20 Torxdriver, attach the Top Trim, using

two screws on each Top Trim piece, to the top of

each door. Hand tighten only. Make sure that the

top of each panel fits snugly behind the lip of the

Top Trim.

Insert the Freezer Panel and Fresh Food Panel.

Carefully push the freezer panel in until it slides

into the slot behind the door handle. Push the filler

panel (required with some door panels) in behind

the decorator panel. Repeat for fresh food panel.

If your model has a dispenser, this step only applies

to the fresh food panel and top freezer panel.

Insert the Bottom Freezer Panel (on dispenser models).

Carefully push the panel in until it slides into the

slot behind the door handle. Push the filler panel

(required with some door panels) in behind the

decorator panel.

Cut-Out

Top Trim Screws

Top

Freezer

Panel

Bottom

Freezer

Panel

Side Trim

Fresh

Food

Panel

Top Trim Screws

20

Inserting the door panels.

Install the Side Trim.

These pieces are tucked inside the refrigerator door

handle.

Do not remove the protective film on the outside of the

Side Trim until the Side Trim is installed.

Fit the bottom of the Side Trim under the Bottom

Trim as illustrated.

Hold the Side Trim against the front face of the

decorator panels and fit the Side Trim under

the Top Trim. Make sure the magnetically attached

Side Trim is fitted correctly and that you are

satisfied with the appearance of all the parts.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Side

Trim

Side

Trim

Bottom Trim

Top Trim

La page charge ...

GE PSS25MGNWW Manuel utilisateur

GE PSS25MGNWW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents