Magmaweld RS 250 M Le manuel du propriétaire

RS 200 M

RS 250 M

RS 300 M

(+90) 444 93 53

magmaweld.com

info@magmaweld.com (+90) 538 927 12 62

USER MANUAL



Magma Mekatronik may modify the information and the images without any prior notice.







FR

RU

TR

EN

MIG/MAG WELDING MACHINE







3

4RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL



1

1.1

1.2

1.3

1.4

1.5

2

2.1

2.2

2.3

2.4

2.4.1

2.4.2

2.4.3

2.4.4

3

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

4

4.1

4.2

4.3

4.4

4.5

5

5.1

5.2

5.3

SAFETY PRECAUTIONS

TECHNICAL INFORMATION

General Information

Machine Components

Product Label

Technical Data

Accessories



Delivery Control

Installation and Operation Recommendations

Mains Plug Connection

Welding Connections

Connections of the Wire Feeder

Grounding Pliers Connections

Connections for Long Harness

Gas Connections

OPERATION

Connection to Mains

Preparation and Connection of the Torch

Selection and Replacement of Wire Feed Rollers

Placing the Wire Spool and Wire Feeding Process

Adjustment of Gas Flow

Using Trigger Modes

Starting and Ending the Welding Process

Welding Parameters



Maintenance

Non-Periodic Maintenance

Troubleshooting

Fuses

Error Codes

ANNEX

Fine Settings in the Wire Feed Unit

Spare Parts Lists

Connection Diagrams

5

11

12

13

14

16

17

18

19

20

21

22

23

24

25

26

27

28

29

32

Contents

5RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL



Be Sure To Follow All Safety Rules In This Manual!

• Safety symbols found in the manual are used to identify potential hazards.

• When any one of the safety symbols are seen in this manual, it must be understood that there is

a risk of injury and the following instructions should be read carefully to avoid potential hazards.

• The possessor of the machine is responsible for preventing unauthorized persons from

accessing the equipment.

• Persons using the machine must be experienced or fully trained in welding / cutting they have to

read the user manual before operation and follow the safety instructions.

Explanation Of Safety

Information

• Read the user manual, the label on the machine and the safety instructions carefully.

• Make sure that the warning labels on the machine are in good condition. Replace missing and

damaged labels.

• Learn how to operate the machine, how to make the checks in a correct manner.

• Use your machine in suitable working environments.

• Improper changes made in your machine will negatively affect the safe operation and its

longevity.

• The manufacturer is not responsible for the consequences resulting from the operation of the

 

Comprehending Safety

Precautions

Explanation Of Safety

Symbols

ATTENTION

Indicates a potentially hazardous situation that could cause injury or damage.

In case if no precaution is taken, it may cause injuries or material losses / damages.

IMPORTANT



DANGER

Indicates a serious danger. In case if not avoided, severe or fatal injuries may occur.

Make certain that the installation procedures comply with national electrical standards



persons.

• Wear dry and sturdy insulated gloves and working apron. Never use wet or damaged gloves and

working aprons.

 

operator must be protective against sparks, splashing and arc radiation.

• Do not work alone. In case of a danger make sure you have someone for help in your working

environment.

• Do not touch the electrode with the bare hand. Do not allow the electrode holder or electrode to

come in contact with any other person or any grounded object.

• Never touch parts that carry electricity.

• Never touch the electrode if you are in contact with the electrode attached to the work surface,

 



 

material that is large enough to cut off the operator’s contact with the work surface.

• Do not connect more than one electrode to the electrode holder.

• Clamp work cable with good metal-to-metal contact to workpiece or worktable as near the weld

as practical.

• Check the torch before operating the machine. Make sure the torch and its cables are in good

condition. Always replace a damaged, worn torch.

• Do not touch electrode holders connected to two machines at the same time since double

open-circuit voltage will be present.

• Keep the machine turned off and disconnect cables when not in use.

• Before repairing the machine, remove all power connections and / or connector plugs or turn

off the machine.

• Be careful when using a long mains cable.

Electric Shocks

May Kill



6RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL



• Turn off the electric power.

• Use non-conducting material, such as dry wood, to free the victim from contact with live parts

or wires.

• Call for emergency services.



• If the victim is not breathing, Administer cardiopulmonary resuscitation (CPR) immediately

after breaking contact with the electrical source. Continue CPR (cardiac massage) until

breathing starts or until help arrives.



• Treat an electrical burn as a thermal burn by applying sterile, cold (iced) compresses. Prevent

contamination, and cover with a clean, dry dressing.

Procedures for

Electric Shock

Long-term inhalation of fumes and gases released from welding / cutting is very dangerous.

• Keep away from the moving parts.



closed and in locked position.

• Wear metal toe shoes against the possibility of heavy objects falling on to your feet.

• Burning sensations and irritations in the eyes, nose and throat are signs of inadequate

ventilation. In such a case, immediately boost the ventilation of the work area, and if the

problem persists, stop the welding / cutting process completely.



• Use a suitable fume extraction system where welding / cutting works are being carried out. If

necessary, install a system that can expel fumes and gases accumulated in the entire workshop.

 



cadmium, zinc, coated or painted materials, use masks that provide fresh air in addition to the

above precautions.

• If the gas tanks are grouped in a separate zone, ensure that they are well ventilated, keep the

main valves closed when gas cylinders are not in use, pay attention to possible gas leaks.

• Shielding gases such as argon are denser than air and can be inhaled instead of air if used in

 

• Do not perform welding / cutting operations in the presence of chlorinated hydrocarbon vapors

released during lubrication or painting operations.

• Some welded / cut parts require special ventilation. The safety rules of products that require

special ventilation should be read carefully. A suitable gas mask should be worn when

necessary.

Fumes and Gases

May Be Harmful To

Your Health

Moving Parts May

Cause Injuries

Make sure all connections are tight, clean, and dry.

• Keep cables dry, free of oil and grease, and protected from hot metal and sparks.

• Bare wiring can kill. Check all cables frequently for possible damage. If a damaged or an

uninsulated cable is detected, repair or replace it immediately.

• Insulate work clamp when not connected to workpiece to prevent contact with any metal

object.

• Make sure that the grounding of the power line is properly connected.

 

• Use AC output ONLY if required for the welding process.

• If AC output is required, use remote output control if present on unit.





• in damp locations or while wearing wet clothing,

 

• when in cramped positions such as sitting, kneeling, or lying,

• when there is a high risk of unavoidable or accidental contact with the workpiece or ground.

For these conditions, use the following equipment in order presented:

• Semiautomatic DC constant voltage (CV) MIG welding machine,

• DC manual MMA welding machine,

• DC or AC welding machine with reduced open-circuit voltage (VRD), if available.

7RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL



• Performing works such as welding / cutting, surface grinding, and brushing cause sparks and

metal particles to splatter. Wear approved protective work goggles which have edge guards

under the welding masks to prevent sustaining possible injuries.

Sparks and Spattering

Particles May Get

Into Eyes and Cause

Damage

• Do not touch the hot parts with bare hands.

• Wait until the time required for the machine to cool down before working on its parts.

• If you need to hold hot parts, use suitable tools, welding / cutting gloves with high-level thermal

 

Hot Parts May Cause

Severe Burns

 

• Protect other naked parts of your body (arms, neck, ears, etc.) with suitable protective clothing

from these rays.



so that people around you will not sustain injuries from arc rays and hot metals.

• This machine is not used for heating of icebound pipes. This operation performed with the

 

Arc Light May Damage

Your Eyes and Skin

• The noise generated by some equipment and operations may damage your hearing ability.

• Wear approved personal ear protective equipment if the noise level is high.

Noise May Cause

Damage To Your

Hearing Ability

• Do not apply welding / cutting operations into completely closed tanks or pipes.

• Before welding to tanks and closed containers, open them, completely empty them, and clean

them. Pay the greatest attention possible to the welding / cutting operations you will perform in

such places.

• Do not weld in tanks and pipes which might have previously contained substances that may

 

• Welding / cutting equipment heats up. For this reason, do not place it on surfaces that could

easily burn or be damaged !

• Do not point the torch towards any part of the body, other persons, or any metal while

unwrapping the welding / cutting wire.

• When welding wire is run manually from the roller especially in thin diameters the wire can slip

out of your hand, like a spring or can cause damage to you or other people around, therefore you

must protect your eyes and face while working on this.

Welding Wires Can

Cause Injuries



explosions.

• Before starting the welding / cutting work, remove these materials form the environment or cover

 

• National and international special rules apply in these areas.

Welding Operations

May Cause Fire and

Explosion

 

extinguishers tubes, water, and sand in easily accessible places.



circuits. Make sure that they are periodically inspected and pay attention that they run reliably.

• Electrical equipment should not be repaired by unauthorized persons.

Errors occurred if failed to do so may result in serious injury or death when using the

equipment.

• The gas circuit elements operate under pressure; explosions may occur as a result of services

provided by unauthorized persons, users may sustain serious injuries.

• It is recommended to perform technical maintenance of the machine and its auxiliary units at

least once a year.

Maintenance Work



Persons To Machines

and Apparatus May

Cause Injuries

8RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL





operations, accompanied by another person.

• Avoid performing welding / cutting operations in such enclosed areas as much as possible.

• Take all necessary precautions when moving the machine. The areas where the machine to be

transported, parts to be used in transportation and the physical conditions and health of the

person carrying out the transportation works should be suitable for the transportation process.

• Some machines are extremely heavy; therefore, make sure that the necessary environmental

safety measures are taken when changing their places.

• If the machine is to be used on a platform, it must be checked that this platform has suitable load

bearing limits.

• If it is to be transported by means of a haulage vehicle (transport trolley, forklift etc.), make sure

of the durableness of the vehicle, and the connection points (carrying suspenders, straps, bolts,

nuts, wheels, etc.) that connect the machine to this vehicle.

• If the machine will be carried manually, make sure the durableness of the machine apparatuses

(carrying suspenders, straps, etc.) and connections.

• Observe the International Labor Organization’s rules on carriage weights and the transport

regulations in force in your country in order to ensure the necessary transport conditions.

• Always use handles or carrying rings when relocating the power-supply sources. Never pull

from torches, cables or hoses. Be absolutely sure to carry gas cylinders separately.

• Remove all interconnections before transporting the welding / cutting equipment, each being

separately, lift and transport small ones using its handles, and the big ones from its handling

rings or by using appropriate haulage equipment, such as forklifts.

Welding / Cutting in





Failure To Take

Precautions During

Transport May Cause

Accidents



 

of tripping over on cables and hoses; yet, large, easily ventilatable, dust-free areas. To prevent

 

 

way that they would not tip over for sure.

• Allow operators to easily access settings and connections on the machine.

Falling Parts May

Cause Injuries Improper positioning of the power-supply sources or other equipment can cause serious injury

to persons and physical damage to other objects.

• Allow the machine to cool down according to operation cycle rates.

• Reduce the current or operation cycle rate before starting the welding / cutting again.

• Do not block the fronts of air vents of the machines.



Excessive Use Of The

Machine Causes

Overheating

Excessive Use Of The

Machine Causes

Overheating

• This device is in group 2, class A in EMC tests according to TS EN 55011 standard.

• This class A device is not intended for use in residential areas where electrical power is supplied

 

compatibility due to radio frequency interference transmitted and emitted in such places.

• Make sure that the work area complies with electromagnetic compatibility (EMC).

Electromagnetic interferences during welding / cutting operations may cause undesired effects

on your electronic devices and network; and the effects of these interferences that may occur

during these operations are under the responsibility of the user.

• If there is any interference, to ensure compliance; extra measures may be taken, such as the

use of short cables, use of shielded (armored) cables, transportation of the welding machine to

 

the work area under protection in terms of EMC.

• To avoid possible EMC damage, make sure to perform your welding / cutting operations as far

away from your sensitive electronic devices as possible (100 m).

This device is not compliant with IEC 61000 -3-12. In case if it is desired to be

connected to the low voltage network used in the home, the installer to make the

electrical connection or the person who will use the machine must be aware that

the machine has been connected in such a manner; in this case the responsibility

belongs to the user.

9RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL



• Ensure that your welding and/or cutting machine has been installed and situated in its place

according to the user manual.



Before installing the welding / cutting equipment, the person in charge of the operation and / or

the user must conduct an inspection of possible electromagnetic interference in the environment.

Aspects indicated below has to be taken into consideration;

a) Other supply cables, control cables, signal and telephone cables, above and below the welding

/ cutting machine and its equipment,

b) Radio and television transmitters and receivers,

c) Computer and other control hardware,

d) Critical safety equipment, e.g. protection of industrial equipment,

e) Medical apparatus for people in the vicinity, e.g. pacemakers and hearing aids,

f) Equipment used for measuring or calibration,

g) Immunity of other equipment in the environment. The user must ensure that the other

equipment in use in the environment is compatible. This may require additional protection

measures.

Considering the time during which the welding / cutting operations or other activities take

place during the day, the boundaries of the investigation area can be expanded according to the

size of the building, the structure of the building and other activities that are being performed

in the building.



for solving the interfering effect. In case if deemed necessary, on-site measurements can also be



(Source: IEC 60974-9).

• The appliance must be connected to the electricity supply in the recommended manner by a

 

 

tube or with an equivalent shielded cable. The housing of the power supply must be connected

and a good electrical contact between these two structures has to be provided.

• The recommended routine maintenance of the appliance must be carried out. All covers on the

body of the machine must be closed and / or locked when the device is in use. Any changes,

other than the standard settings without the written approval of the manufacturer, cannot be

 

possibly occur.



the work area, in a side by side manner. Welding / cutting cables should not be wound in any

way.



machine to pull metal parts on to itself. To avoid this attraction, make sure that the metal

 

interconnected metal materials.

• In cases where the workpiece cannot be connected to the ground due to electrical safety, or

because of its size and position (for example, in building marine vessel bodies or in steel

construction manufacturing), a connection between the workpiece and the grounding may

reduce emissions in some cases, it should be kept in mind that grounding of the workpiece may

cause users to sustain injuries or other electrical equipment in the environment to break down.

In cases where necessary, the workpiece and the grounding connection can be made as a direct

connection, but in some countries where direct connection is not permissible, the connection

can be established using appropriate capacity elements in accordance with local regulations

and ordinances.

• Screening and shielding of other devices and cables in the work area can prevent aliasing

 

applications.

Evaluation Of

Electromagnetic

Suitability Of The

Work Area

Electromagnetic

Interferance

Reduction Methods



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

Electromagnetic Field

(EMF)

10 RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL



• Choose the welding / cutting method and welding machine for the welding work you are to

perform.

• Select the welding / cutting current and/or voltage to match the material and thickness you are

going to weld.

• If you have to wait for a long time before you start your welding / cutting work, turn off the machine

after the fan has cooled it down. Our machines with smart fan control will turn off on their own.

• This device is not domestic waste. It must be directed to recycling within the framework of the

European Union directive and national laws.

• Obtain information from your dealer and authorized persons about the waste management of

your used machines.

Waste Procedure



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

• Welding / cutting and electric cables should not be wrapped around the body of the machine in

any way,

• The body of the machine should not get caught between the welding / cutting cables. The source

cables must be kept away from the body of the machine, both being placed side by side,

• The return cable must be connected to the workpiece as close as possible to the work area,

• The welding / cutting machine should not rest against the power unit, ensconce on it and not

work too close to it,

• Welding / cutting work should not be performed when carrying the wire supply unit or power

unit.

EMF may also disrupt the operation of medical implants (materials placed inside the body), such

as pacemakers. Protective measures should be taken for people who carry medical implants. For

example, access limitation may be imposed for passers-by, or individual risk assessments may be

conducted for welders. Risk assessment should be conducted and recommendations should be

made by a medical professional for users who carry medical implants.

• Do not expose the machine to rain, prevent the machine from splashing water or

pressurized steam.

Protection



WARRANTY FORM

Please visit our website www.magmaweld.com/warranty-form/wr for warranty form.

11RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL

1

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

16-a 16-b

16-c

2

3

4

5

6

TECHNICAL INFORMATION

1.1 General Information

1.2 Machine Components



RS 200 M, RS 250 M and RS 300 M are 3 phase step controlled, Constant Voltage industrial MIG/MAG machines



and thermally protected against over heating. The welding voltage adjustment ranges are, for 200 model 14 steps

between 17-36 V, for 250 models 21 steps between 20-51 V, for 300 models 21 steps between 19 - 44 V.

Wire feeding unit is a robust 4 wheel drive system which is designed as a separate box from the power source in

order to cover larger work areas. It contains a wire feeding motor-gearbox assembly, an electronic control card

and a gas valve, therefore this unit should be handled carefully at site. The wheels under the box are for the ease

of the welder to move the box as he welds, but the box shouldn’t be pulled across the work area by the torch. Even

though you can manufacture with these machines in a big range of current scale all day long, model 200 is

optimized for 0.8 mm, 250 for 1.0mm and 300 for 1.0 mm heavy-duty applications.



 Torch Connector

 Thin Adjustment Switch

On / Off and Coarse Adjustment Switch

 Wire Feed Unit Connector

 Gas Outlet

Welding Current Plug Socket

 Trigger Mode Switch

 Wire Speed Adjustment Button

 Turn Table

 Handle

 Lifting Eye

Voltmeter

Ammeter

 Workpiece Cable Socket (-)

Wheel

Wire Feeder Harness

 Welding Current Plug

Wire Feed Unit Control Cable

 Gas Hose

Mains Cable

Drum Feeding Wire Inlet

Insurance Group

 CO Heater Socket

Gas Inlet

Gas Cylinder Security Chain

Fan Output

Gas Cylinder Transport Platform

12 RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL

1.3 Product Label

X

U

I

U



U



I



MIG/MAG Welding

Horizontal Characteristic

Mains Input 3-Phase Alternating

Current

Suitable for Operation at Hazardous

Environments

Direct Current

Duty Cycle

Open Circuit Voltage

Rated Welding Current

Mains Voltage and Frequency

Protection Class

Rated Welding Voltage

Rated Power

Rated Mains Current







4 minutes should be kept idle for the machine cool down (zone 2).





6 min. 6 min.6 min.4 min. 4 min. 4 min. Time (min.)



13RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL



1.4 Technical Data



400

865 x 510 x 780

3 x 7

300



101

19 - 44

IP 21

40 - 300

Mains Voltage (3-Phase 50-60 Hz)

Voltage Adjustment and Number of Levels

Welding Current Range

Protection Class

Rated Power

Dimensions (l x w x h)

Rated Welding Current

Weight

Open Circuit Voltage

TECHNICAL DATA

Mains Voltage (3-Phase 50-60 Hz)

Voltage Adjustment and Number of Levels

Welding Current Range

Protection Class

Rated Power

Dimensions (l x w x h)

Rated Welding Current

Weight

Open Circuit Voltage

TECHNICAL DATA

UNIT

V

VDC

kVA

mm

ADC

kg

mm



400

865 x 510 x 780

3 x 7

250



101

19.7 - 51

IP 21

57 - 250

UNIT

V

VDC

kVA

mm

ADC

kg

mm



400

865 x 510 x 780

2 x 7

240



101

17 - 36

IP 21

40 - 240

UNIT

V

VDC

kVA

mm

ADC

kg

mm

Mains Voltage (3-Phase 50-60 Hz)

Voltage Adjustment and Number of Levels

Welding Current Range

Protection Class

Rated Power

Dimensions (l x w x h)

Rated Welding Current

Weight

Open Circuit Voltage

TECHNICAL DATA

14 RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL

1.5 Accessories





Workpiece Clamp and Cable



Gas Hose

MIG/MAG Mix/Argon Accessory Set*

QTY

1

7905212505 (25 mm² - 5 m)

7920000515

7907000002

7920000510

7905212505 (25 mm² - 5 m)

7920000525

7907000002

7920000520

7905212505 (25 mm² - 5 m)

7920000535

7907000002

7920000530









Workpiece Clamp and Cable



Gas Hose

MIG/MAG Mix/Argon Accessory Set*

QTY

1



Workpiece Clamp and Cable



Gas Hose

MIG/MAG Mix/Argon Accessory Set*

QTY

1



15RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL



CO Heater

Gas Regulator (Mix)

Gas Regulator (CO)

Lava MIG 25 (3 m) Air Cooled MIG Torch

QTY

1

7020009002

7120025003

7020001005

7020001004



CO Heater

Gas Regulator (Mix)

Gas Regulator (CO)

Lava MIG 25 (3 m) Air Cooled MIG Torch

Lava MIG 35 (3 m) Air Cooled MIG Torch

QTY

1

7020009002

7120025003

7120035003

7020001005

7020001004



CO Heater

Gas Regulator (Mix)

Gas Regulator (CO)

Lava MIG 35 (3 m) Air Cooled MIG Torch

QTY

1

7020009002

7120035003

7020001005

7020001004



16 RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL



2.1 Delivery Control

Make sure that all the materials you have ordered have been received. If any material is missing or damaged,

contact your place of purchase immediately.

The standard box includes the following;

 

• Workpiece clamp and cable • User manual

• Gas hose • Welding Wire

In case of a damaged delivery, record a report, take a picture of the damage and report to the transport

company together with a photocopy of the delivery note. If the problem persists, contact the customer service.

2.2 Installation and Operation Recommendations

• Lifting rings or forklifts should be used to move the machine. Do not lift the machine with the gas cylinder.

Place the power supply on a hard, level, smooth surface where it will not fall or tip over.

• For a better performance, place the machine at least 30 cm away from the surrounding objects. Pay attention

to overheating, dust and moisture near the machine. Do not operate the machine under direct sunlight. If the

 

• Avoid welding outdoors in windy and rainy weather circumstances. If welding is necessary in such cases,

protect the welding area and the welding machine with a curtain and canopy.

• When positioning the machine, make sure that materials such as walls, curtains, boards do not prevent easy

access to the machine’s controls and connections.

• If you weld indoors, use a suitable fume extraction system. Use breathing apparatus if there is a risk of

 



damage the machine and this may invalidate the warranty.



• Tighten the ground wire as close as possible to the workpiece. Do not allow the welding current to pass

through equipment other than the welding cables such as the machine itself, gas cylinder, chain and roller

bearing.

• When the gas cylinder is placed on the machine, secure the gas cylinder by connecting the chain immediately.

If you will not place the gas cylinder on the machine, secure the gas cylinder to the wall with a chain.

• The electrical outlet on the back of the machine is for the C0 heater. Never connect a device to the C0 outlet

other than the C0 heater !

Symbols and their meanings on the device

Welding may be dangerous. Proper working conditions should be ensured and necessary precautions

should be taken. Specialists are responsible for the machine and have to be equipped with the necessary

equipment and those who are not relevant should be kept away from the welding area.

This device is not compatible with IEC 61000-3-12. If it is desired to connect to the low voltage mains used

in homes, it is essential that the installer or the person who will operate the machine to make the electrical

connection has information on the machine’s connectivity. In this case the responsibility will be assumed

by the person who will perform the installation or by the operator.

The safety symbols and warning notes on the device and in the operating instructions must be observed

and the labels must not be removed.

Grids are intended for ventilation. The openings should not be covered in order to provide good cooling and

no foreign objects should be inserted.

Installation

17RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL

2.3 Mains Plug Connection

For your safety, never use the mains cord of the machine without a plug.

• No plug has been connected to the mains cable since there may different types of outlets available in plants,

 

the grounding cable marked with and a yellow / green color is present.

• After connecting the plug to the cable, do not attach it to the outlet at this stage.

16-a

16-b

16-c

Be sure that the connections are fastened tightly. Loose or incorrect fastening may cause

overheating or gas leakage.



• Place the wire feeder on to the turn table on the machine.

• Connect the blue gas hose to gas outlet bush in front of the power source.

• Connect the control cable to the control socket in front of the power source.

• Connect the welding plug into the welding cable connection outlet in front of the power source.

2.4 Welding Connections

2.4.1 Connections of the Wire Feeder

2.4.2 Grounding Pliers Connections

• Grounding cable sockets with different inductance values

allow welding with lower spatter in a wide current range.

Socket for low current and small wire diameters socket,

for high current and large wire diameters or

socket should be preferred.

• Connect the grounding pliers wire to one of the grounding wire

sockets on the machine and tighten by turning it to the right.



pliers to the workpiece as close as possible to the welding

area.

Installation

18 RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL

16-c

16-b

16-a



• Machines with harness longer than 5 meter have detachable harness and wire feeding connection in order to

lift easier. Both ends of the harness are the same, therefore sockets and connectors must be connected to the

wire feeding unit same as the connections to the front side of the machine.

• If your machine has harness longer than 5 meter, connect the harness to the wire feeding unit as seen below.

2.4.3 Connections for Long Harness

• If you will use the gas cylinder on the gas cylinder transport platform on the machine, place the gas cylinder

here and secure it with a chain.

• If you will not place the gas cylinder on the machine, secure the gas cylinder to the wall with a chain.

• Use safety regulators and heaters according to the standards for work safely to achieve the best results.

• Make sure the size of the hose connection of the gas regulator you are using is 3/8 .

• Open the gas cylinder valve keeping your head and face away from the outlet of the valve and keep it open for

5 seconds. By this means, possible sediment and impurities will be discharged.

• If the CO heater to the gas cylinder. After connecting the gas

regulator to the CO heater, insert the plug of the CO heater into the CO heater outlet on the back of the

machine.

• If the CO heater will not be used, connect the gas regulator directly to the gas cylinder.

• Connect one end of the tube hose to the gas regulator and tighten the clamp. Connect the other end to the gas

inlet at the back of the machine and tighten the nut.



hear a noise and/or detect a smell of gas as a leak indicator, examine your connections and eliminate leakage.

2.4.4 Gas Connections

Gas Cylinder Valve  Gas Regulator

Gas Cylinder  Manometer

CO Heater Flowmeter

Chain Flow Adjustment Valve

CO Heater Energy CableGas Hose



1

2

5

4

3

6

7 8

9

10

Installation

19RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.com USER MANUAL

Torch Nut



3.2 Preparation and Connection of the Torch

• Check the 3-phase with a voltmeter before connecting the machine to

the mains. After detecting that each phase is 400V (± 40V), attach the

plug into the wall outlet.

• Start the machine with the on / off switch.

• Turn the machine off by turning the switch back to the “0” position

after hearing the fan sound and seeing the ammeter and voltmeter

lights are on.

• Use the torch according to the capacity of your machine and

the welding you will perform.

• Make sure that the diameters of the spiral and contact nozzle inside

the torch match the diameter of the welding wire you will use. Replace

the spiral and contact nozzle if necessary.

• To change the spiral, remove the nozzle, contact nozzle and adapter

respectively.

• Afterwards, remove the spiral nut on the torch connector side with

 

the spiral inside the torch.



the spiral nut.

• Cut the excess of the spiral from the torch head with a side chisel at

the point where the gas distributor (contact nozzle holder)

immediately ends as shown on the right, so that there is no gap

between the spiral and the contact nozzle. File the cut point to make it

blunt and burr free.

• Attach it to torch torch connector and tighten the nut tightly.















Nozzle

Contact Tip

Adapter

Nut of Liner

Liner

3.1 Connection to Mains

When plugging the power plug into the outlet, make sure that the power switch is set to “0”.

OPERATION

20 RS 200 M / RS 250 M / RS 300 M

EN

www.magmaweld.comUSER MANUAL

3.3 Selection and Replacement of Wire Feed Rollers

• Open the cover of the wire feed part. You will see the four-roller wire feed system.

Engine

 Euro Connector

 Pressure Roller Handle

 Pressure Rollers

 Wire Feed Rollers

 WF Roller Screws



1

2

3

4

5

6

• Use wire feed rollers suitable for the material and diameter of

the welding wire you will use. Use V-grooved wire feed rollers for

steel and stainless steel, corrugated V-grooves for cored wires

and U corrugated ones for aluminum.

• If you need to replace the wire feed rollers, pull the pressure

roller lever toward your side and after lifting the pressure rollers,

remove the wire feed roller screws and remove the existing

rollers.









• After inserting the rollers, you will use, re-insert the screws and

lower the pressure rollers and lock the pressure roller lever onto

the rollers.



0.8 mm



La page charge ...

Magmaweld RS 250 M Le manuel du propriétaire

Ce manuel convient également à

Magmaweld RS 250 M Le manuel du propriétaire

dans d''autres langues

Documents connexes