Magmaweld ID 250 E Le manuel du propriétaire

ID 250E

(+90) 444 93 53

magmaweld.com

info@magmaweld.com (+90) 538 927 12 62

USER MANUAL



Magma Mekatronik may modify the information and the images without any prior notice.







3ID 250E

FR

RU

AR

TR

EN

DC WELDING INVERTER

   



POSTE ONDULEUR DC



4ID 250E

EN

www.magmaweld.comUSER MANUAL

CONTENTS

Contents

1

1.1

1.2

1.3

1.4

1.5

2

2.1

2.2

2.3

2.4

2.5

2.6

3

3.1

4

4.1

4.2

4.3

5

5.1

5.2

SAFETY PRECAUTIONS

TECHNICAL INFORMATION

General Information

Machine Components

Product Label

Technical Data

Accessories

INSTALLATION

Delivery Control

Installation and Operation Recommendations

Mains Plug Connection

Connection to Mains

Connections for MMA Welding

Connections for TIG Welding

OPERATION

User Interface

MAINTENANCE AND SERVICE

Maintenance

Troubleshooting

Error Codes

ANNEX

Spare Parts List

Connection Diagrams

5

11

12

13

14

15

16

17

19

20

21

23

24

5ID 250E

EN

www.magmaweld.com USER MANUAL

Safety Precautions

Be Sure To Follow All Safety Rules In This Manual!

• Safety symbols found in the manual are used to identify potential hazards.

• When any one of the safety symbols are seen in this manual, it must be understood that there is

a risk of injury and the following instructions should be read carefully to avoid potential hazards.

• The possessor of the machine is responsible for preventing unauthorized persons from

accessing the equipment.

• Persons using the machine must be experienced or fully trained in welding / cutting they have to

read the user manual before operation and follow the safety instructions.

Explanation Of Safety

Information

• Read the user manual, the label on the machine and the safety instructions carefully.

• Make sure that the warning labels on the machine are in good condition. Replace missing and

damaged labels.

• Learn how to operate the machine, how to make the checks in a correct manner.

• Use your machine in suitable working environments.

• Improper changes made in your machine will negatively affect the safe operation and its

longevity.

• The manufacturer is not responsible for the consequences resulting from the operation of the

 

Comprehending Safety

Precautions

Explanation Of Safety

Symbols

ATTENTION

Indicates a potentially hazardous situation that could cause injury or damage.

In case if no precaution is taken, it may cause injuries or material losses / damages.

IMPORTANT



DANGER

Indicates a serious danger. In case if not avoided, severe or fatal injuries may occur.

Make certain that the installation procedures comply with national electrical standards



persons.

• Wear dry and sturdy insulated gloves and working apron. Never use wet or damaged gloves and

working aprons.

 

operator must be protective against sparks, splashing and arc radiation.

• Do not work alone. In case of a danger make sure you have someone for help in your working

environment.

• Do not touch the electrode with the bare hand. Do not allow the electrode holder or electrode to

come in contact with any other person or any grounded object.

• Never touch parts that carry electricity.

• Never touch the electrode if you are in contact with the electrode attached to the work surface,

 



 

material that is large enough to cut off the operator’s contact with the work surface.

• Do not connect more than one electrode to the electrode holder.



as practical.

• Check the torch before operating the machine. Make sure the torch and its cables are in good

condition. Always replace a damaged, worn torch.

• Do not touch electrode holders connected to two machines at the same time since double

 

• Keep the machine turned off and disconnect cables when not in use.

• Before repairing the machine, remove all power connections and / or connector plugs or turn

off the machine.

• Be careful when using a long mains cable.

Electric Shocks

May Kill

SAFETY PRECAUTIONS

6ID 250E

EN

www.magmaweld.comUSER MANUAL

Safety Precautions

• Turn off the electric power.



or wires.

• Call for emergency services.



• If the victim is not breathing, Administer cardiopulmonary resuscitation (CPR) immediately

after breaking contact with the electrical source. Continue CPR (cardiac massage) until

breathing starts or until help arrives.



• Treat an electrical burn as a thermal burn by applying sterile, cold (iced) compresses. Prevent

contamination, and cover with a clean, dry dressing.

Procedures for

Electric Shock

Long-term inhalation of fumes and gases released from welding / cutting is very dangerous.

• Keep away from the moving parts.



closed and in locked position.

• Wear metal toe shoes against the possibility of heavy objects falling on to your feet.

• Burning sensations and irritations in the eyes, nose and throat are signs of inadequate

ventilation. In such a case, immediately boost the ventilation of the work area, and if the

problem persists, stop the welding / cutting process completely.



• Use a suitable fume extraction system where welding / cutting works are being carried out. If

necessary, install a system that can expel fumes and gases accumulated in the entire workshop.

 



cadmium, zinc, coated or painted materials, use masks that provide fresh air in addition to the

above precautions.

• If the gas tanks are grouped in a separate zone, ensure that they are well ventilated, keep the

main valves closed when gas cylinders are not in use, pay attention to possible gas leaks.

• Shielding gases such as argon are denser than air and can be inhaled instead of air if used in

 

• Do not perform welding / cutting operations in the presence of chlorinated hydrocarbon vapors

released during lubrication or painting operations.

• Some welded / cut parts require special ventilation. The safety rules of products that require

special ventilation should be read carefully. A suitable gas mask should be worn when

necessary.

Fumes and Gases

May Be Harmful To

Your Health

Moving Parts May

Cause Injuries

Make sure all connections are tight, clean, and dry.

• Keep cables dry, free of oil and grease, and protected from hot metal and sparks.

• Bare wiring can kill. Check all cables frequently for possible damage. If a damaged or an

uninsulated cable is detected, repair or replace it immediately.

• Insulate work clamp when not connected to workpiece to prevent contact with any metal

object.

• Make sure that the grounding of the power line is properly connected.

 

• Use AC output ONLY if required for the welding process.

• If AC output is required, use remote output control if present on unit.

Additional safety precautions are required when any of the following electrically hazardous

conditions are present :

• in damp locations or while wearing wet clothing,

 

• when in cramped positions such as sitting, kneeling, or lying,

• when there is a high risk of unavoidable or accidental contact with the workpiece or ground.

For these conditions, use the following equipment in order presented:

• Semiautomatic DC constant voltage (CV) MIG welding machine,

• DC manual MMA welding machine,



7ID 250E

EN

www.magmaweld.com USER MANUAL

Safety Precautions

• Performing works such as welding / cutting, surface grinding, and brushing cause sparks and

metal particles to splatter. Wear approved protective work goggles which have edge guards

under the welding masks to prevent sustaining possible injuries.

Sparks and Spattering

Particles May Get

Into Eyes and Cause

Damage

• Do not touch the hot parts with bare hands.

• Wait until the time required for the machine to cool down before working on its parts.

 

 

Hot Parts May Cause

Severe Burns

 

• Protect other naked parts of your body (arms, neck, ears, etc.) with suitable protective clothing

from these rays.



so that people around you will not sustain injuries from arc rays and hot metals.

• This machine is not used for heating of icebound pipes. This operation performed with the

 

Arc Light May Damage

Your Eyes and Skin

• The noise generated by some equipment and operations may damage your hearing ability.

• Wear approved personal ear protective equipment if the noise level is high.

Noise May Cause

Damage To Your

Hearing Ability

• Do not apply welding / cutting operations into completely closed tanks or pipes.

• Before welding to tanks and closed containers, open them, completely empty them, and clean

them. Pay the greatest attention possible to the welding / cutting operations you will perform in

such places.

• Do not weld in tanks and pipes which might have previously contained substances that may

 

• Welding / cutting equipment heats up. For this reason, do not place it on surfaces that could

easily burn or be damaged !

• Do not point the torch towards any part of the body, other persons, or any metal while

unwrapping the welding / cutting wire.

• When welding wire is run manually from the roller especially in thin diameters the wire can slip

out of your hand, like a spring or can cause damage to you or other people around, therefore you

must protect your eyes and face while working on this.

Welding Wires Can

Cause Injuries



explosions.

• Before starting the welding / cutting work, remove these materials form the environment or cover

 

• National and international special rules apply in these areas.

Welding Operations

May Cause Fire and

Explosion

 

extinguishers tubes, water, and sand in easily accessible places.



circuits. Make sure that they are periodically inspected and pay attention that they run reliably.

• Electrical equipment should not be repaired by unauthorized persons.

Errors occurred if failed to do so may result in serious injury or death when using the

equipment.

• The gas circuit elements operate under pressure; explosions may occur as a result of services

provided by unauthorized persons, users may sustain serious injuries.

• It is recommended to perform technical maintenance of the machine and its auxiliary units at

least once a year.

Maintenance Work



Persons To Machines

and Apparatus May

Cause Injuries

8ID 250E

EN

www.magmaweld.comUSER MANUAL

Safety Precautions



operations, accompanied by another person.

• Avoid performing welding / cutting operations in such enclosed areas as much as possible.

• Take all necessary precautions when moving the machine. The areas where the machine to be

transported, parts to be used in transportation and the physical conditions and health of the

person carrying out the transportation works should be suitable for the transportation process.

• Some machines are extremely heavy; therefore, make sure that the necessary environmental

safety measures are taken when changing their places.

• If the machine is to be used on a platform, it must be checked that this platform has suitable load

bearing limits.

• If it is to be transported by means of a haulage vehicle (transport trolley, forklift etc.), make sure

of the durableness of the vehicle, and the connection points (carrying suspenders, straps, bolts,

nuts, wheels, etc.) that connect the machine to this vehicle.

• If the machine will be carried manually, make sure the durableness of the machine apparatuses

(carrying suspenders, straps, etc.) and connections.

• Observe the International Labor Organization’s rules on carriage weights and the transport

regulations in force in your country in order to ensure the necessary transport conditions.



from torches, cables or hoses. Be absolutely sure to carry gas cylinders separately.

• Remove all interconnections before transporting the welding / cutting equipment, each being

separately, lift and transport small ones using its handles, and the big ones from its handling

rings or by using appropriate haulage equipment, such as forklifts.

Welding / Cutting in





Failure To Take

Precautions During

Transport May Cause

Accidents



 

 

 

 

way that they would not tip over for sure.

• Allow operators to easily access settings and connections on the machine.

Falling Parts May

Cause Injuries Improper positioning of the power-supply sources or other equipment can cause serious injury

to persons and physical damage to other objects.

• Allow the machine to cool down according to operation cycle rates.

• Reduce the current or operation cycle rate before starting the welding / cutting again.

• Do not block the fronts of air vents of the machines.



Excessive Use Of The

Machine Causes

Overheating

Excessive Use Of The

Machine Causes

Overheating

• This device is in group 2, class A in EMC tests according to TS EN 55011 standard.

• This class A device is not intended for use in residential areas where electrical power is supplied

 

compatibility due to radio frequency interference transmitted and emitted in such places.

• Make sure that the work area complies with electromagnetic compatibility (EMC).

Electromagnetic interferences during welding / cutting operations may cause undesired effects

on your electronic devices and network; and the effects of these interferences that may occur

during these operations are under the responsibility of the user.

• If there is any interference, to ensure compliance; extra measures may be taken, such as the

use of short cables, use of shielded (armored) cables, transportation of the welding machine to

 

the work area under protection in terms of EMC.

• To avoid possible EMC damage, make sure to perform your welding / cutting operations as far

away from your sensitive electronic devices as possible (100 m).



connected to the low voltage network used in the home, the installer to make the

electrical connection or the person who will use the machine must be aware that

the machine has been connected in such a manner; in this case the responsibility

belongs to the user.

9ID 250E

EN

www.magmaweld.com USER MANUAL

Safety Precautions

• Ensure that your welding and/or cutting machine has been installed and situated in its place

according to the user manual.



Before installing the welding / cutting equipment, the person in charge of the operation and / or

the user must conduct an inspection of possible electromagnetic interference in the environment.

Aspects indicated below has to be taken into consideration;

a) Other supply cables, control cables, signal and telephone cables, above and below the welding

/ cutting machine and its equipment,

b) Radio and television transmitters and receivers,

c) Computer and other control hardware,

d) Critical safety equipment, e.g. protection of industrial equipment,

e) Medical apparatus for people in the vicinity, e.g. pacemakers and hearing aids,

f) Equipment used for measuring or calibration,

g) Immunity of other equipment in the environment. The user must ensure that the other

equipment in use in the environment is compatible. This may require additional protection

measures.

h) Considering the time during which the welding / cutting operations or other activities take

place during the day, the boundaries of the investigation area can be expanded according to the

size of the building, the structure of the building and other activities that are being performed

in the building.









• The appliance must be connected to the electricity supply in the recommended manner by a

 

 

tube or with an equivalent shielded cable. The housing of the power supply must be connected

and a good electrical contact between these two structures has to be provided.

• The recommended routine maintenance of the appliance must be carried out. All covers on the

body of the machine must be closed and / or locked when the device is in use. Any changes,

other than the standard settings without the written approval of the manufacturer, cannot be

 

possibly occur.



the work area, in a side by side manner. Welding / cutting cables should not be wound in any

way.



machine to pull metal parts on to itself. To avoid this attraction, make sure that the metal

 

interconnected metal materials.

• In cases where the workpiece cannot be connected to the ground due to electrical safety, or

because of its size and position (for example, in building marine vessel bodies or in steel

construction manufacturing), a connection between the workpiece and the grounding may

reduce emissions in some cases, it should be kept in mind that grounding of the workpiece may

cause users to sustain injuries or other electrical equipment in the environment to break down.

In cases where necessary, the workpiece and the grounding connection can be made as a direct

connection, but in some countries where direct connection is not permissible, the connection

can be established using appropriate capacity elements in accordance with local regulations

and ordinances.

• Screening and shielding of other devices and cables in the work area can prevent aliasing

 

applications.

Evaluation Of

Electromagnetic

Suitability Of The

Work Area

Electromagnetic

Interferance

Reduction Methods



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

Electromagnetic Field

(EMF)

10 ID 250E

EN

www.magmaweld.comUSER MANUAL

Safety Precautions

• Choose the welding / cutting method and welding machine for the welding work you are to

perform.

• Select the welding / cutting current and/or voltage to match the material and thickness you are

going to weld.

• If you have to wait for a long time before you start your welding / cutting work, turn off the machine

after the fan has cooled it down. Our machines with smart fan control will turn off on their own.

• This device is not domestic waste. It must be directed to recycling within the framework of the

European Union directive and national laws.

• Obtain information from your dealer and authorized persons about the waste management of

your used machines.

Waste Procedure



(EMF).

All operators must follow the following procedures to minimize the risk of exposure to EMF;



secured as far as possible with the joining materials (tape, cable ties etc.).

• The operator’s body and head should be kept as far away from the welding / cutting machine

and cables as possible,

• Welding / cutting and electric cables should not be wrapped around the body of the machine in

any way,

• The body of the machine should not get caught between the welding / cutting cables. The source

cables must be kept away from the body of the machine, both being placed side by side,

• The return cable must be connected to the workpiece as close as possible to the work area,

• The welding / cutting machine should not rest against the power unit, ensconce on it and not

work too close to it,

• Welding / cutting work should not be performed when carrying the wire supply unit or power

unit.

EMF may also disrupt the operation of medical implants (materials placed inside the body), such

as pacemakers. Protective measures should be taken for people who carry medical implants. For



conducted for welders. Risk assessment should be conducted and recommendations should be

made by a medical professional for users who carry medical implants.

• Do not expose the machine to rain, prevent the machine from splashing water or

pressurized steam.

Protection



WARRANTY FORM

Please visit our website www.magmaweld.com/warranty-form/wr for warranty form.

11ID 250E

EN

www.magmaweld.com USER MANUAL

TECHNICAL INFORMATION

1.1 General Information



output, can be easily transported, and can burn MMA up to 5.0 mm. It provides excellent arc characteristics for

all rutile and basic covered electrodes. The machine is fan cooled and thermally protected against overheating.

Figure 1 : ID 250E

1- 6-

2- Digital Display 7- Welding and Ground Cable Socket (+)

3- Arc Force Pot 8- On/Off Switch

4-  9- Power Cable Inlet

5- Current Adjustment Pot

8 9

1

2

3

5

6 7

4

1.2 Machine Components

Technical Information

12 ID 250E

EN

www.magmaweld.comUSER MANUAL

1.3 Product Label

X

U

I

U

IP21S

U

S

I



Direct Current

MMA Welding

TIG Welding

Vertical Characteristic





Environments







4 minutes should be kept idle for the machine cool down (zone 2).

Duty Cycle



6 min. 6 min.6 min.4 min. 4 min. 4 min. Time (min.)

Technical Information

Duty Cycle

Open Circuit Voltage

Rated Welding Current

Mains Voltage and Frequency

Protection Class

Rated Welding Voltage

Rated Power

Rated Mains Current

13ID 250E

EN

www.magmaweld.com USER MANUAL





1





1

Rack (6, vertical)

Lava TIG 20V (4 m) TIG Torch

Rack (4, vertical)

Transport Trolley

Rack (9, vertical)

Lava TIG 20V (8 m) TIG Torch

7900000807

7111020004

7900000804

7900000600

7900000809

7111020008

V

VDC

kVA

mm

kg

mm

ID 250E

ADC

TECHNICAL DATA

Rated Power

Welding Current Range

Open Circuit Voltage

Weight

Protection Class

Stick Electrode Diameter Range

Dimensions (l x w x h)

UNIT

Technical Information

1.4 Technical Data

1.5 Accessories

QTY

QTYOPTIONAL ACCESSORIES

PRODUCT CODE

STANDARD ACCESSORIES

Workpiece Clamp and Cable

Electrode Clamp and Cable

400



75

250

12.7

491 x 160 x 311

10.75

IP 21S



14 ID 250E

EN

www.magmaweld.comUSER MANUAL

Make sure that all the materials you have ordered have been received. If any material is missing or damaged,

contact your place of purchase immediately.

The standard box includes the following;

 

• Workpiece clamp and cable • User manual

• Electrode clamp and cable

In case of a damaged delivery, record a report, take a picture of the damage and report to the transport

company together with a photocopy of the delivery note. If the problem persists, contact the customer service.

2.2 Installation and Operation Recommendations

Symbols and their meanings on the device

Welding may be dangerous. For welding should ensure proper working conditions, and the authorized

person should take necessary precautions. Specialists are responsible for the machine and have to be

equipped with the necessary equipment and those who are not relevant should be kept away from the

welding area.



mains used in homes, it is essential that the installer or the person who will operate the machine

to make the electrical connection must have the information on the machine’s connectivity. In this

case, the person who will perform the installation or the operator will assume responsibility.

The safety symbols and warning notes on the device and in the operating instructions must be observed

and the labels must not be removed.

Grids are intended for ventilation. The openings should not be covered to provide good cooling and no

foreign objects should be inserted.

• For better performance, place the machine at least 30 cm away from surrounding objects. Beware of

overheating, dust and humidity around the machine. Do not operate the machine in direct sunlight. In

 

cycle rate.

• Avoid welding outdoors in the presence of wind and rain. If welding is necessary in such cases, protect the

welding area and the welding machine with curtains and awnings.

• When positioning the machine, make sure that materials such as walls, curtains and panels do not prevent

easy access to the control and connections of the machine.

• If welding indoors, use a suitable fume extraction system. If there is a risk of breathing welding fumes and

gas indoors, use breathing apparatus.



damage the machine and void the warranty.





over equipment other than welding cables.

• Welding cables and mains cable must not be wrapped around the machine body during operation.

INSTALLATION

2.1 Delivery Control

Installation

15ID 250E

EN

www.magmaweld.com USER MANUAL

2.3 Mains Plug Connection

For your safety, never use the mains cord of the machine without a plug.

• No plug has been connected to the mains cable since there may different types of outlets available in plants,

 

• After connecting the plug to the cable, do not attach it to the outlet at this stage.

2.5 Connections for MMA Welding

• According to the polarity of the electrode to be used, insert welding cables into the appropriate socket and

 

• Connect the earth clamp tightly to the workpiece as close as possible to the welding area.



steels. Please follow the electrode manufacturer’s recommendations.

Figure 3 : MMA Welding Connections

Covered Electrode

Diameter (mm)

Recommended Welding Current

Rutile Basic

2.0

2.5

3.25

4.0

5.0





















When plugging the power plug into the outlet, make sure that the power switch is set to “0”.

2.4 Connection to Mains



mains. After detecting that each phase is 400V (± 40V), attach the plug into

the wall outlet.

• Start the machine with the on / off switch.

• Turn the machine off by turning the switch back to the “0” position after

hearing the fan sound and seeing the ammeter and voltmeter lights are on.

Figure 2 : Mains Connection

Installation

16 ID 250E

EN

www.magmaweld.comUSER MANUAL

2.6 Connections for TIG Welding

Figure 5 : TIG Welding Connection

The following table shows approximate values;

Figure 4 : Gas Cylinder Connection

Electrode Diameter

(mm)

Nozzle Diameter

(mm)

Welding Current

(ADC)

Gas Flow

(lt/min)

1.0

1.6

6.3

9.5







Installation

• TIG torch with a valve should be used.

• Connect the TIG torch power cable to the negative welding socket and

the earth cable to the positive welding socket of the machine.

• Install the Argon gas regulator onto the Argon gas cylinder.

• Connect the gas hose of the torch to the gas regulator.

• Keep the gas cylinder valve open for a while so that possible sediment

and particles are ejected.

17ID 250E

EN

www.magmaweld.com USER MANUAL

• The SPOT mode is selected by using the menu button, the relevant led will light when this mode is selected.

• Developed for who work with short welding seams.

• This mode should be selected when shorter welding length is desired.



mode. The led of the selected mode will be lit.

• MMA mode is selected by using the Menu button and the relevant led will light when this mode is selected.

• MMA mode should be selected when welding of rutile or basic electrodes is desired.

2-) SPOT MODE

3-) WELDING MODE SELECTION KEY

4-) MMA MODE

1-) DIGITAL DISPLAY

• Welding current, welding voltage and other parameters can be monitored.

4

5 6 7

3 2 1

3.1 User Interface

OPERATION

Operation

18 ID 250E

EN

www.magmaweld.comUSER MANUAL



to the right and left.

• The adjusted value is monitored on the digital display.

• By pressing the current adjustment button, you can switch between current and voltage values during

welding or when idle.

7-) CURRENT ADJUSTMENT POT

6-) HOT START SETTING

When electrode welding is started, high current is supplied for 1 second up to two times the welding current



initial welding will be added to the main current as much as the percentage of the main current.



be 300A and the maximum current of the machine will be 250 A. The output current will return to the set current



Current



Set Current

Time

5-) ARC FORCE SETTING

Current

Welding Current

Welding Voltage

Sticking Condition

Time

Arc Force increases the welding current and prevents arc interruption based on the welding voltage if the



cannot exceed the maximum current of the machine.



be 300A and the maximum current of the machine will be 250 A.

Operation

19ID 250E

EN

www.magmaweld.com USER MANUAL

MAINTENANCE AND SERVICE



responsible for accidents that may occur as a result of interventions by unauthorized persons.

• You can obtain the parts to be used in the repairs from our authorized services. The use of original spare parts

will extend the life of your machine and prevent performance losses.



• All warranty provisions will become void due to any interference not authorized by Magmaweld within the

warranty period.

• Make sure you comply with the applicable safety rules during maintenance and repair works.

• Disconnect the machine’s plugs from the mains before carrying out any repairs and wait for 10 seconds for

the capacitors to discharge.

4.1 Maintenance

Daily Maintenance

• Do not remove the warning labels on the device. Replace the worn/torn labels with

the new ones. Labels can be obtained from the authorized service.

• Check your torch, clamps and cables. Pay attention to the connections and the

durableness of the parts. Replace the damaged/defective parts with the new ones.

Do not ever make additions to/repair the cables.

• Ensure adequate space for ventilation.



 

process.

• Clean and tighten fasteners such as bolts and nuts.

• Check the electrode clamp and grounding clamp cables.

• Open the side covers of the machine and clean with low pressure dry air. Do not

apply compressed air to electronic components at close distance.

• Check the socket to which the power supply plug of the machine is connected. If

there is any looseness in the power cable connection points of the socket, remove

such looseness. If there is an arc or expansion in the socket slots, replace them with

new ones.

• Check the power supply plug of the machine. If there is any looseness in the power

cable connection points in the electricity plug, remove such looseness. If there is an

arc or deformation at the ends of the plug, replace it with a new one.

or

Every 6 Months

NOTE: The above mentioned periods are the maximum ones that should be applied if no problems are

encountered in your device. Depending on the work load and contamination of your work environment,

you can repeat the above processes more frequently.

Maintenance and Service

20 ID 250E

EN

www.magmaweld.comUSER MANUAL

The following tables contain possible errors to be encountered and their solutions.

4.2 Troubleshooting

Error Solution

Machine does not work at all

The machine welds poorly

• Make sure that the machine is connected to power

• Check that the mains connections are correct

• Check the mains power supply fuses, mains cable and its plug

• Check the on / off operating switch

• If you have made all the checks and if the problem still persists, please

contact the authorized service center

• Make sure that the machine’s grounding pliers are connected to the

workpiece

• Make sure that the cables are secure and that the connection points are

not worn

• Make sure that the parameter and process selection are correct

• According to the process you have chosen, follow the steps below:

1- Check the pole that the electrode must be connected and the

current value that must be set on the machine

2- 

3- Make sure that the tungsten tip is clean

4- Make sure the durableness of the welding torch

5- If you have made all the checks, if the problem still persists, please

contact the authorized service center

Maintenance and Service

La page charge ...

Magmaweld ID 250 E Le manuel du propriétaire

Magmaweld ID 250 E Le manuel du propriétaire

dans d''autres langues

Documents connexes