VTech CS5319 Guide de démarrage rapide

Marque: VTech

Modèle: CS5319

Catégorie: Téléphones

Taper: Guide de démarrage rapide

Ce manuel convient également à

Go to www.vtechphones.com

to register your product for enhanced

warranty support and latest VTech

product news.

Quick start guide

CS5319

CS5319-15

CS5319-2

DECT 6.0 cordless telephone

Scan the QR code for

support information

Speciﬁcations are subject to change without notice.

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency Handset: 1921.536-1928.448 MHz

Telephone base: 1921.536-1928.448 MHz

Channels 5

Nominal

effective range Maximum power allowed by FCC and IC. Actual

operating range may vary according to environmental

conditions at the time of use.

Power

requirement Handset: 2.4V 300mAh Ni-MH battery

Telephone base: 6V DC @ 400mA

Charger: 6V DC @ 400mA

Memory Phonebook: 50 memory locations;

up to 30 digits and 15 characters

Caller ID log: 30 memory locations;

up to 24 digits and 15 characters

Call block: 20 entries

Compatible with

Hearing

d T-Coil

TIA-1083

Telephones identiﬁed with this logo have reduced

noise and interference when used with most T-coil

equipped hearing aids and cochlear implants. The

TIA-1083 Compliant Logo is a trademark of the

Telecommunications Industry Association. Used under

license.

The ENERGY STAR® program (www.energystar.gov)

recognizes and encourages the use of products that

save energy and help protect our environment. We are

proud to mark this product with the ENERGY STAR® label

indicating it meets the latest energy efﬁciency guidelines.

Technical speciﬁcations

Important safety instructions

When using your telephone equipment, basic safety precautions

should always be followed to reduce the risk of ﬁre, electric shock

and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. CAUTION: Do not install the telephone base at a height

above 2 meters.

4. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

5. Do not use this product near water such as near a bath tub,

wash bowl, kitchen sink, laundry tub or a swimming pool, nor

in a wet basement or shower.

6. Do not place this product on an unstable table, shelf, stand or

other unstable surfaces.

7. Avoid placing the telephone system in places with extreme

temperature, direct sunlight, or other electrical devices.

Protect your phone from moisture, dust, corrosive liquids and

fumes.

8. Slots and openings in the back or bottom of the telephone

base and handset are provided for ventilation. To protect

them from overheating, these openings must not be blocked

by placing the product on a soft surface such as a bed, sofa

or rug. This product should never be placed near or over a

radiator or heat register. This product should not be placed in

any area where proper ventilation is not provided.

9. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home or ofﬁce, consult your

dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not install

this product where the cord may be walked on.

11. Never push objects of any kind into this product through the

slots in the telephone base or handset because they may touch

dangerous voltage points or create a short circuit. Never spill

liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble this

product, but take it to an authorized service facility. Opening

or removing parts of the telephone base or handset other than

speciﬁed access doors may expose you to dangerous voltages

or other risks. Incorrect reassembling can cause electric shock

when the product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer servicing to

an authorized service facility under the following conditions:

• When the power supply cord or plug is damaged or

frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operation instructions. Improper

adjustment of other controls may result in damage and

often requires extensive work by an authorized technician

to restore the product to normal operation.

• If the product has been dropped and the telephone base

and/or handset has been damaged.

• If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an

electrical storm. There is a remote risk of electric shock from

lightning.

16. Do not use the telephone to report a gas leak in the vicinity

of the leak. Under certain circumstances, a spark may be

created when the adapter is plugged into the power

outlet, or when the handset is replaced in its cradle. This

is a common event associated with the closing of any

electrical circuit. The user should not plug the phone into

a power outlet, and should not put a charged handset

into the cradle, if the phone is located in an environment

containing concentrations of ﬂammable or ﬂame-supporting

gases, unless there is adequate ventilation. A spark in such

an environment could create a ﬁre or explosion. Such

environments might include: medical use of oxygen without

adequate ventilation; industrial gases (cleaning solvents;

gasoline vapors; etc.); a leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear when

it is in normal talk mode.

18. The power adapter is intended to be correctly oriented in a

vertical or ﬂoor mount position. The prongs are not designed

to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

19. For pluggable equipment, the socket-outlet shall be installed

near the equipment and shall be easily accessible.

20. CAUTION: Use only the batteries indicated in this

manual. There may be a risk of explosion if a wrong type

of battery is used for the handset. Use only the supplied

rechargeable batteries or replacement batteries (BT162342/

BT262342) for the handset. Do not dispose of batteries in a

ﬁre. They may explode. Dispose of used battery according

to the instruction. Disconnect the telephone line from the

equipment before open the battery door.

Do not use the battery in following conditions:

• High or low extreme temperature during use, storage or

transportation.

• Replacement of a battery with an incorrect type that can

defeat a safeguard.

• Disposal of a battery into ﬁre or a hot oven, or mechanically

crushing or cutting of a battery, that can result in an explosion.

• Leaving a battery in an extremely high temperature

surrounding environment that can result in an explosion

or the leakage of ﬂammable liquid or gas.

• A battery subjected to extremely low air pressure that can

result in an explosion or the leakage of ﬂammable liquid

or gas.

21. Use only the adapter included with this product. Incorrect

adapter polarity or voltage can seriously damage the product.

22. The applied nameplate is located at the bottom or near of the

product. SAVE THESE INSTRUCTIONS

Battery

• Use only the battery provided or equivalent. To order a

replacement, visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to phones.vtechcanada.com or

call 1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check with local waste

management codes for special disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is

corrosive and may cause burns or injury to the eyes or skin.

The electrolyte may be toxic if swallowed.

• Exercise care in handling batteries in order not to create a

short circuit with conductive materials.

• Charge the battery provided with this product only in

accordance with the instructions and limitations speciﬁed in

this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless telephones and

implanted cardiac pacemakers. Supported by the U.S. Food and

Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches from the

pacemaker.

• Should NOT place wireless telephones directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

• Should use the wireless telephone at the ear opposite the

pacemaker.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless telephone

convenient create some limitations. Telephone calls are

transmitted between the telephone base and the cordless

handset by radio waves, so there is a possibility that the

cordless telephone conversations could be intercepted

by radio receiving equipment within range of the cordless

handset. For this reason, you should not think of cordless

telephone conversations as being as private as those on

corded telephones.

• Electrical power: The telephone base of this cordless

telephone must be connected to a working electrical outlet.

The electrical outlet should not be controlled by a wall

switch. Calls cannot be made from the cordless handset if the

telephone base is unplugged, switched off or if the electrical

power is interrupted.

• Potential TV interference: Some cordless telephones operate

at frequencies that may cause interference to televisions and

VCRs. To minimize or prevent such interference, do not place

the telephone base of the cordless telephone near or on top

of a TV or VCR. If interference is experienced, moving the

cordless telephone farther away from the TV or VCR often

reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling batteries

in order not to create a short circuit with conducting material

such as rings, bracelets and keys. The battery or conductor

may overheat and cause harm. Observe proper polarity

between the battery and the battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose of

these batteries in a safe manner. Do not burn or puncture

the battery. Like other batteries of this type, if burned or

punctured, they could release caustic material which could

cause injury.

What’s in the box

Quick

start

guide

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

1 set for

CS5319

CS5319-15

2 sets for

CS5319-2

1 set

CS5319-2

Connect and activate Setup

Basic operation Phonebook Caller ID

Quiet mode

Call Block Ringer Settings

Connect the

telephone base

If you subscribe to digital

subscriber line (DSL)

high-speed Internet

service through your

telephone line, make

sure you connect a DSL

ﬁlter (not included) to the

telephone wall jack.

Install the battery

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1535

THIS SIDE UP

RS LE HAUT

h Ni-MH)

BATTERIES.

ESPILES.

CR1535

Display

The battery is low and needs

charging.

The battery is charging.

The battery is fully charged.

Handset ringer is muted.

New voicemail received from your

telephone service provider.

NEW

There are new caller ID log entries.

ECO The ECO mode activates

automatically to reduce power

consumption when the handset is

within range of the telephone base.

Find handset

Charge the battery

12 hrs

After the telephone is installed or power returns following

a power outage and battery depletion, the handset will

prompt you to set the date and time.

Date and time

Follow the steps below to set the date and time. For

example, if the date is 25 January, 2023, and the time is

11:07 AM:

When the handset

prompts you to set

the date and time

Date:MM/DD/YY

ECO

Date:01/2?/YY

ECO

1. Enter the date.

Date:01/25/23

ECO

Time: 1?:MM --

ECO

Time: 11:07 AM

ECO

2. Press SELECT. 3. Enter the time. 4. Press SELECT.

NOTE: If you have skipped the prompt, you can set up

again by pressing MENU to enter Set date/time, and

then follow the steps above.

Change LCD language settings

Follow the steps below to set the date and time. For

example, if the date is 25 January, 2023, and the time is

11:07 AM:

HANDSET

ECO

11:07 1/25

Settings

ECO

1. Press MENU.2. Press q/p to scroll to

Settings, then press SELECT.

LCD language

ECO

English

ECO

3. Press SELECT to select LCD

language.4. Press q/p to choose your

desired language and press

SELECT.

When the telephone is in the Quiet Mode, all tones

(except the FIND HS tone) are muted.

1. Press and hold .

2. Enter the numer of hours (1-12) you would like the telephone

to be in Quiet Mode for.

3. Press SELECT to save.

CS5319-X (US)

CS5319-X (CA)

Answer a call

Make a call

Press - OR -

Enter the

phone number

- OR - - OR - Press any dialing

key to answer

Press

Speakerphone

Press

End a call

Press

Volume

Press

The phonebook can store up to 50 entries, which are

shared by all handsets. Each entry may consist of a

telephone number up to 30 digits, and a name up to 15

characters.

Add a phonebook entry

Follow the steps below to set the date and time. For

example, if the date is 25 January, 2022, and the time is

11:07 AM:

HANDSET

ECO

800-595-9511

ECO

11:07 1/25

Enter number

800-595-9511_

ECO

1. Enter the phone

number. 2. Press MENU. 3. Press SELECT.

Enter name

ECO

Mike Smith_

ECO

4. Enter the

phonebook

entry name.

5. Press SELECT.

Review phonebook entries

HANDSET

ECO

Mike Smith

800-595-9511

ECO

1. Press . 2. Press q/p to

browse the

entries.

Delete a phonebook entry

When your desired phonebook entry displays on the

handset screen:

Mike Smith

800-595-9511

ECO

Delete entry?

ECO

1. Press DELETE. 2. Press SELECT.

11:07 1/25

If you subscribe to caller ID service, information about

each caller appears after the ﬁrst or second ring.

The caller ID log stores up to 30 entries. Each entry has

up to 24 digits for the phone number and 15 characters

for the name.

Review Caller ID log entries

HANDSET

ECO

Mike Smith

800-595-9511

ECO

1. Press . 2. Press q/p to browse the entries.

Dial a caller ID log entry

When your desired

caller ID entry

displays on the

handset screen

Mike Smith

800-595-9511

ECO

11:07 1/25

Press

-OR-

Save a Caller ID log entry to the phonebook

When your

desired caller ID

entry displays

on the handset

screen

Mike Smith

800-595-9511

ECO

11:07 1/25

To phonebook

ECO

1. Press MENU. 2. Press SELECT

to select To

phonebook.

Enter number

800-595-9511_

ECO

Enter name

ECO

Mike Smith_

ECO

3. Edit the phone

number if

needed.

4. Press SELECT. 5. Edit the name

if needed, then

press SELECT.

Delete a Caller ID log entry

When your desired Caller ID entry

displays on the handset screen:

Press DELETE.

Mike Smith

800-595-9511

ECO

11:07 1/25

If you subscribe to caller ID service, you can set the

telephone to block unknown calls and certain undesired

calls. The call block list can store up to 20 entries.

Add a call block entry

HANDSET

ECO

Call block

ECO

Block list

ECO

1. Press MENU.2. Press q/p

to scroll to

Call block,

then press

SELECT.

3. Press

SELECT to

select Block

list.

Add new entry

ECO

Enter number

800-595-9511_

ECO

Enter name

ECO

4. Press q/p to

scoll to Add

new entry, then

press SELECT.

5. Enter

number, and

then press

SELECT.

6. Enter

name, and

then press

SELECT.

Review a call block list entry

HANDSET

ECO

Call block

ECO

Block list

ECO

1. Press MENU.2. Press q/p

to scroll to

Call block,

then press

SELECT.

3. Press SELECT

to select

Block list.

Review

ECO

4. Press SELECT to

select Review.

Delete a call block list entry

When your desired call block list entry

displays on the handset screen:

Press DELETE.

Block unknown calls

HANDSET

ECO

Call block

ECO

Calls w/o num

ECO

1. Press MENU.2. Press q/p

to scroll to

Call block,

then press

SELECT.

3. Press q/p to

scroll to Calls

w/o num,

then press

SELECT.

Block

ECO

4. Press q/p

to scroll to

Block, then

press SELECT.

11:07 1/25

Mike Smith

800-595-9511

ECO

11:07 1/25

Adjust the ringer volume

HANDSET

ECO

Ringers

ECO

Ringer volume

ECO

1. Press MENU.2. Press q/p

to scroll

to Ringer,

then press

SELECT.

3. Press SELECT

to select

Ringer

volume.

Volume:Off

ECO

4. Press q/p

to scroll

to adjust

volume level,

then press

SELECT to

save.

11:07 1/25

To ﬁnd misplaced

handsets, press

/FIND HS at the back of

the telephone base.

All idle handsets ring and

display ** Paging **.

To end paging, press

/FIND HS again or press

OFF on the handset.

Ringer Settings (cont’d) Voicemail Service Need Help?

For C-UL compliance only

The RBRC seal

FCC, ACTA and IC regulations California energy commission battery

charging testing instructions

Limited warranty

VTech Communications, Inc. and its suppliers assume no

responsibility for any damage or loss resulting from the use of

this user’s manual. VTech Communications, Inc. and its suppliers

assume no responsibility for any loss or claims by third parties that

may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR

97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Disclaimer and Limitation

of Liability

For operations and guides to help you using your telephone, and

for the latest information and supports, go and check the online

help and FAQs. Use your smartphone or mobile device to access.

• Go to https://help.vtechphones.com/CS5319 (US);

https://phones.vtechcanada.com/en/support/

technical-support/product/4532 (CAN); OR

• Scan the QR code on the right. Launch the

camera app or QR code scanner app on

your smartphone or tablet. Hold the device’s

camera up to the QR code and frame it. Tap

the notiﬁcation to trigger the redirection of the

online help.

You can also call our Customer Support at

1(800) 595-9511 [in the US] or 1(800) 267-7377

[in Canada] for help.

Recycle this product when you are

done with it

Scan the QR code on the right or visit

www.vtechphones.com/recycle.

(For the US only)

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles ou

d’électrocution, suivez toujours ces mesures préventives de base

lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le nettoyer.

N’utilisez pas de nettoyeurs liquides ni en aérosol. N’utilisez qu’un

chiffon doux et légèrement humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur

supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un

lavabo, d’un évier de cuisine, d’un bac de lavage ou d’une piscine,

ou dans un sous-sol humide ou sous la douche.

6. Ne déposez pas ce téléphone sur un chariot, support ou table

chancelants. L’appareil pourrait tomber et être sérieusement

endommagé.

7. Évitez d’installer le système téléphonique dans les endroits

soumis à une température extrême, à la lumière directe du

soleil ou à proximité immédiate d’autres appareils électriques

ou électroniques. Protégez votre téléphone contre les sources

d’humidité, la poussière, les vapeurs et les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures

d’aération situées à l’arrière ou en dessous. Aﬁn d’empêcher

la surchauffe, ces ouvertures ne doivent pas être obstruées

en plaçant l’appareil sur un lit, divan, tapis ou autre surface

similaires. Ne placez pas cet appareil à proximité d’un élément de

chauffage ni d’une plinthe électrique. De plus, ne l’installez pas

dans une unité murale ou un cabinet fermé qui ne possède pas

d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur les étiquettes de l’appareil. Si vous ne connaissez pas

le voltage de votre maison, consultez votre marchand ou votre

fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil

dans un endroit sécuritaire, là où personne ne pourra trébucher sur

la ligne d’alimentation ni le cordon téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures de

cet appareil, car ils pourraient toucher à des points de tension

dangereux ou court-circuiter des pièces, ce qui constituerait un

risque d’incendie ou d’électrocution. N’échappez pas de liquides

dans l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne démontez pas

l’appareil, mais apportez-le plutôt à un centre de service qualiﬁé

s’il doit être réparé. En enlevant le couvercle, vous vous exposez

à des tensions dangereuses ou autres dangers similaires. Un

remontage inadéquat peut être à l’origine d’une électrocution

lors d’une utilisation ultérieure de l’appareil. Débranchez

l’appareil avant de procéder au nettoyage. Utilisez un chiffon

humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et communiquez

avec le département de service à la clientèle de VTech dans les cas

suivants :

• Lorsque le cordon d’alimentation est endommagé ou écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité telle que la

pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en respectant

les instructions de fonctionnement. Réglez uniquement

les commandes indiquées dans le les instructions de

fonctionnement. Les réglages incorrects des autres

commandes pourraient provoquer un dommage qui pourrait

exiger un travail exhaustif de la part d’un technicien autorisé

aﬁn de rétablir le fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ou le combiné a

été endommagé.

• Si le produit afﬁche une nette diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant un

orage. Les éclairs peuvent être à l’origine d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à

proximité de la fuite. En certaines circonstances, une ﬂammèche

pourrait être provoquée lorsque l’adaptateur est branché à

une prise de courant, ou lorsque le combiné est déposé sur le

socle. Ceci est un événement commun associé à la fermeture

d’un circuit électrique. L’utilisateur ne devrait pas brancher le

téléphone à une prise de courant, et ne devrait pas déposer

le combiné chargé sur le socle, si le téléphone se trouve à

proximité d’un endroit comportant des concentrations de gaz

inﬂammables, à moins que la ventilation soit adéquate. Une

ﬂammèche dans un tel endroit pourrait provoquer un incendie

ou une explosion. De tels environnements peuvent comprendre:

des endroits où l’on utilise de l’oxygène médical sans ventilation

adéquate; des gaz industriels (dissolvants de nettoyage, des

vapeurs d’essence, etc.); une fuite de gaz naturel, etc.

17. Ne placez que le combiné de votre téléphone près de votre oreille

lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour être orientés en position

verticale ou montés au sol. Les broches ne sont pas conçues pour

maintenir l’adaptateur en place si celui-ci est barnché dans une

prise au plafond ou sous une table/ armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle

de prise de courant doit etre installe a proximite du materiel et doit

etre aisement accessible.

20. MISE EN GARDE: Il peut y avoir un risque d’explosion

si vous utilisez le mauvais type de piles pour le téléphone.

N’utilisez que les piles rechargeable inclus ou les piles de

rechange (BT162342/BT262342). N’incinérez pas les piles. Celles-ci

risqueraient d’exploser.

21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation

d’un adaptateur dont la polarité ou la tension serait inadéquate

risque d’endommager sérieusement le produit et mettre votre

sécurité en péril.

22. La plaque signalétique appliquée est située au bas ou à proximité

du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent. Pour commander une

pile de recharge, visitez notre site Web au

www.vtechphones.com ou composez le 800-595-9511. Au

Canada, visitez le phones.vtechcanada.com ou composez le

800-267-7377.

• Ne jetez pas la pile au feu. Vériﬁez les instructions spéciﬁques de

mise aux rebus auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en

échapperait est corrosif et pourrait causer des brûlures ou des

blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn d’éviter les

courts-circuits provoqués par des matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les instructions et

limites spéciﬁées dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones

numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme

de recherche indépendante, a mené une évaluation pluridisciplinaire

des interférences entre les téléphones sans ﬁl portatifs et les

stimulateurs cardiaques implantés dans l’organisme. Appuyée par

l’Administration des aliments et drogues (FDA) des États-Unis, la ﬁrme

WTR recommande aux médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au moins six

pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur

le stimulateur cardiaque, tel que dans une poche de chemise,

lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant sur l’oreille

qui se trouve dans la direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de

risque pour les détenteurs de simulateurs cardiaques causés

par les gens qui utilisent un téléphone sans ﬁl à proximité de

ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent

des avantages pour les téléphones sans ﬁl afﬁchent également

des restrictions. Les appels téléphoniques sont transmis entre le

combiné sans ﬁl et le socle par le biais d’ondes radio ; il y a donc

la possibilité que vos conversations téléphoniques sans ﬁl soient

interceptées par des équipements de réception radio se trouvant

dans la portée du combiné sans ﬁl. Pour cette raison, vous ne

devez pas percevoir les communications téléphoniques sans ﬁl

comme étant aussi conﬁdentielles que celles des téléphones à

cordons.

Alimentation électrique : Le socle de ce téléphone sans ﬁl

doit être branché à une prise électrique fonctionnelle. La prise

électrique ne doit pas être contrôlée par un interrupteur mural.

Les appels ne pourront pas être effectués du combiné sans ﬁl

si le socle est débranché ou mis hors tension ou si le courant est

coupé.

Possibilité d’interférences aux téléviseurs : Certains téléphones

sans ﬁl fonctionnent sur des fréquences pouvant causer des

interférences aux téléviseurs et aux magnétoscopes. Pour réduire

ou prévenir de telles interférences, ne placez pas le socle du

téléphone sans ﬁl près ou sur un téléviseur ou magnétoscope. S’il

y a présence de parasites, il est conseillé d’éloigner le téléphone

sans ﬁl du téléviseur ou du magnétoscope aﬁn de réduire

possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de ne

pas les court-circuiter avec des bagues, bracelets ou clés. Les

piles ou le conducteur peut surchauffer et causer des blessures.

Respectez la polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel :

Jetez ces blocs-piles de manière écologique et sécuritaire. Ne

les incinérez pas et ne les percez pas. Tel que les autres piles de

ce type, elles pourraient dégager une matière toxique qui peut

causer des blessures corporelles si elles sont brûlées ou percées.

The RBRC seal on the nickel-metal hydride

battery indicates that VTech Communications,

Inc. is voluntarily participating in an industry

program to collect and recycle these batteries at

the end of their useful lives, when taken out of

service within the United States and Canada.

The program provides a convenient alternative to placing used

nickel-metal hydride batteries into the trash or municipal waste,

which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the

spent battery at local retailers participating in the program or at

authorized VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery recycling

and disposal bans/restrictions in your area. VTech’s involvement

in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered

trademarks of Call2recycle, Inc.

FCC Part 15

NOTE: This equipment has been tested and found to

comply with the requirements for a Class B digital device

under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

WARNING: Changes or modiﬁcations to this equipment not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation

is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation. Privacy of communications

may not be ensured when using this telephone.

To ensure safety of users, the FCC/ISEDC has established

criteria for the amount of radio frequency energy that can

be safely absorbed by a user or bystander according to

the intended usage of the product. This product has been

tested and found to comply with the FCC/ISEDC criteria. The

handset may be safely held against the ear of the user. The

telephone base shall be installed and used such that parts

of the user’s body other than the hands are maintained at a

distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian

requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC

rules and with technical requirements adopted by the

Administrative Council for Terminal Attachments (ACTA).

The label on the back or bottom of this equipment contains,

among other things, a product identiﬁer in the format

US:AAAEQ##TXXXX. This identiﬁer must be provided to

your telephone service provider upon request.

The plug and jack used to connect this equipment to

premises wiring and the telephone network must comply

with applicable Part 68 rules and technical requirements

adopted by ACTA. A compliant telephone cord and

modular plug is provided with this product. It is designed

to be connected to a compatible modular jack that is

also compliant. An RJ11 jack should normally be used for

connecting to a single line. See the installation instructions in

the user’s manual.

The Ringer Equivalence Number (REN) is used to determine

how many devices you may connect to your telephone line

and still have them ring when you are called. The REN for this

product is encoded as the 6th and 7th characters following

the US: in the product identiﬁer (e.g., if ## is 03, the REN is

0.3). In most, but not all areas, the sum of all RENs should be

ﬁve (5.0) or less. For more information, please contact your

telephone service provider.

This equipment must not be used with Party Lines. If you

have specially wired alarm dialing equipment connected to

your telephone line, ensure the connection of this equipment

does not disable your alarm equipment. If you have

questions about what will disable alarm equipment, consult

your telephone service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged

from the modular jack until the problem has been corrected.

Repairs to this telephone equipment can only be made

by the manufacturer or its authorized agents. For repair

procedures, follow the instructions outlined under the

Limited warranty.

If this equipment is causing harm to the telephone network,

the telephone service provider may temporarily discontinue

your telephone service. The telephone service provider

is required to notify you before interrupting service. If

advance notice is not practical, you will be notiﬁed as soon

as possible. You will be given the opportunity to correct the

problem and the telephone service provider is required

to inform you of your right to ﬁle a complaint with the FCC.

Your telephone service provider may make changes in its

facilities, equipment, operation, or procedures that could

affect the proper functioning of this product. The telephone

service provider is required to notify you if such changes are

planned.

If this product is equipped with a corded or cordless handset,

it is hearing aid compatible.

If this product has memory dialing locations, you may choose

to store emergency telephone numbers (e.g., police, ﬁre,

medical) in these locations. If you do store or test emergency

numbers, please:

Remain on the line and brieﬂy explain the reason for the call

before hanging up.

Perform such activities in off-peak hours, such as early

morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is

subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Privacy of communications may not be ensured when using

this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number

only signiﬁes that the Industry Canada technical speciﬁcations

were met.

The Ringer Equivalence Number (REN) for this terminal

equipment is 0.1. The REN indicates the maximum number

of devices allowed to be connected to a telephone

interface. The termination of an interface may consist of any

combination of devices subject only to the requirement that

the sum of the RENs of all the devices not exceed ﬁve.

This product meets the applicable Innovation, Science and

Economic Development Canada technical speciﬁcations.

This telephone is set up to comply with the energy-conserving

standards right out of the box. These instructions are intended

for California Energy Commission (CEC) compliance testing only.

When the CEC battery charging testing mode is activated, all

telephone functions, except battery charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the

power outlet. Make sure all handsets are plugged with

charged batteries before proceeding.

2. While you press and hold FIND HS at the back of the

telephone base, plug the telephone base power adapter

back to the power outlet.

3. After about 10 seconds, release FIND HS and

immediately press it again within two seconds.

When the phone successfully enters the CEC battery charging

testing mode, all handsets display To register HS... and ...see

manual alternately.

When the phone fails to enter this mode, repeat steps 1 to 3

above.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the

power outlet, and then plug it back in. Then the telephone

base is powered up as normal.

2. Press and hold FIND HS at the back of the telephone

base for about four seconds.

3. Press #/QUIET on the handset and it shows Registering....

The handset shows Registered and you hear a beep when

the registration process completes. This process takes

about 60 seconds.

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder

of a valid proof of purchase (“Consumer” or “you”) that the

Product and all accessories provided in the sales package

(“Product”) are free from defects in material and workmanship,

pursuant to the following terms and conditions, when installed

and used normally and in accordance with the Product

operating instructions. This limited warranty extends only to

the Consumer for Products purchased and used in the United

States of America and Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will repair or replace at VTech’s option, without

charge, a Materially Defective Product. If we repair the Product,

we may use new or refurbished replacement parts. If we

choose to replace the Product, we may replace it with a new or

refurbished Product of the same or similar design. We will retain

defective parts, modules, or equipment. Repair or replacement

of the Product, at VTech’s option, is your exclusive remedy.

VTech will return the repaired or replacement Products to you in

working condition. You should expect the repair or replacement

to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase. If VTech repairs or replaces

a Materially Defective Product under the terms of this limited

warranty, this limited warranty also applies to the repaired or

replacement Product for a period of either (a) 90 days from the

date the repaired or replacement Product is shipped to you

or (b) the time remaining on the original one-year warranty;

whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper

installation, abnormal operation or handling, neglect,

inundation, ﬁre, water or other liquid intrusion.

2. Product that has been subjected to contact with liquid,

water, rain, extreme humidity or heavy perspiration,

sand, dirt or the like; but then only to the extent the

damage was not caused by incorrectly securing the

waterproof handset’s protective elements, for example,

failing to properly close a seal), or such protective

elements are damaged or missing (e.g. a cracked battery

door), or subjecting a Product to conditions beyond its

stated speciﬁcations or limits (e.g. 30 minutes in 1 meter

of fresh water).

3. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech;

4. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable

or antenna systems;

5. Product to the extent that the problem is caused by use

with non-VTech accessories;

6. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible;

7. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes);

8. Product returned without a valid proof of purchase (see

item 2 below); or

9. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the United States of America,

please visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual

- a check of the Product’s controls and features may save you a

service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in

the transport of the Product(s) to the service location. VTech

will return repaired or replaced Product under this limited

warranty. Transportation, delivery or handling charges are

prepaid. VTech assumes no risk for damage or loss of the

Product in transit. If the Product failure is not covered by this

limited warranty, or proof of purchase does not meet the terms

of this limited warranty, VTech will notify you and will request

that you authorize the cost of repair prior to any further repair

activity. You must pay for the cost of repair and return shipping

costs for the repair of Products that are not covered by this

limited warranty.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents

including the Product to the VTech service location

along with a description of the malfunction or difﬁculty;

and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the Product.

There are no other express warranties. No one is authorized to

make modiﬁcations to this limited warranty and you should not

rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc

legal rights, and you may also have other rights, which vary

from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness for a

particular purpose and merchantability (an unwritten warranty

that the Product is ﬁt for ordinary use) are limited to one year

from the date of purchase. Some states/provinces do not

allow limitations on how long an implied warranty lasts, so the

above limitation may not apply to you. In no event shall VTech

be liable for any indirect, special, incidental, consequential,

or similar damages (including, but not limited to lost proﬁts

or revenue, inability to use the Product or other associated

equipment, the cost of substitute equipment, and claims by

third parties) resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may

not apply to you.

Please retain your original sales receipt as proof of purchase

CS5319-X US

CS5319-X CA

Change the ringer tone

HANDSET

ECO

Ringers

ECO

Ringer tone

ECO

1. Press MENU.2. Press q/p

to scroll

to Ringer,

then press

SELECT.

3. Press SELECT

to select

Ringer tone,

then press

SELECT.

Tone:8

ECO

4. Press q/p to

select a tone

(1-10), then

press SELECT

to save.

11:07 1/25

Your telephone supports voicemail service offered

by your telephone service provider (subscription is

required, and fees may apply.

Voicemail service

Support by Telephone service provider

Subscription Yes

Fees May apply

Answer

incoming calls • Usually after 2 rings.

• It can be changed by contacting your

telephone service provider.

Storage Server or System

Display new

messages Handset

Retrieve

messages Press and hold on the dialpad,

and enter an access number and/

or passcode from your telephone

service provider.

Set a speed dial voicemail number

This feature lets

you save your

voicemail number

for quick access

when you press

and hold the

key.

HANDSET

ECO

Settings

ECO

1. Press MENU.2. Press q/p

to scroll to

Settings, then

press SELECT.

Voicemail #

ECO

Voicemail #

ECO

3. Press q/p

to scroll to

Voicemail #,

then press

SELECT.

4. Enter your

voicemail access

number, then

press SELECT to

save.

Clear the voicemail indicator

Use this feature

to turn off the

displayed icon on

your handset LCD.

It does not delete

your voicemail

messages. As

long as you have

new voicemail

messages, your

telephone service

provider will

continue to send

the signal to turn

on the indicator.

HANDSET

ECO

Settings

ECO

1. Press MENU.2. Press q/p

to scroll to

Settings, then

press SELECT.

Clr voicemail

ECO

Clr voicemail

ECO

3. Press q/p to

scroll to Clr

voicemail,

then press

SELECT.

4. A conﬁrmation

tone plays to

indicate that the

icon has been

cleared.

11:07 1/25 11:07 1/25

VTech CS5319 Guide de démarrage rapide

Marque: VTech

Modèle: CS5319

Catégorie: Téléphones

Taper: Guide de démarrage rapide

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS5319 Quick start guide

VTech CS5319 Guide de démarrage rapide

Ce manuel convient également à

VTech CS5319 Guide de démarrage rapide

dans d''autres langues

Documents connexes