Chief TPS2642 Manuel utilisateur

TPS2642
Chief
Marque
Chief
Modèle
TPS2642
Catégorie
Mur
Taper
Manuel utilisateur

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
Truss/Pole Static Mount
TPS Series
TPS Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow
the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is
the installer’s responsibility to make sure all components
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the TPS does not exceed 150 lbs
(68.04 kg).
•The weight capacity of the TPS may be LIMITED to
the lowest weight capacity of any other component
or accessory used within the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center
for examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The TPS mount is designed for
installation to a variety of pipe/truss dimensions and
can span a distance of up to 14" O.D.
--SAVE THESE INSTRUCTIONS--
Installation Instructions TPS Series
3
DIMENSIONS
DIMENSIONS: INCHES
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN.THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN 1/2” AND 2” IN DEPTH
ANDMAY AFFECT LOCATION OF DISPLAY
ONTHE MOUNT.
SEE PSB-XXXX DRAWING ALSO.
ATTACHESTO POLE/TRUSS USING
TPK SERIES CLAMPS (NOT INCLUDED)
APPROXIMATE CENTER OF DISPLAY
TOP MOUNTING BUTTON ON
PSB-XXXX DRAWING GOES HERE
TPS Series Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Measure
Medir
Messen
Medir
Misurare
Meten
Mesurer
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Hammer
Martillo
Hammer
Martelo
Martello
Hamer
Marteau
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Installation Instructions TPS Series
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2 (included)
5/32"
9/16"
REQUIRED PARTS (NOT INCLUDED)
[TPK Truss/Pole Kit] (example)
x 4 x 8 x 8
TPK-4
or
TPK-5
Truss/Pole Kit
G (1)
[Interface bracket kit]
(example)
A (1)
[TPS mount assembly]
C (2)
3/8"
B (1)
[Truss plate]
E (2)
3/8"
D (2)
1.055" x .406 x .250"
F (1)
1.125" X .390" X .094"
Faceplate
TPS Series Installation Instructions
6
INSTALLATION
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
The TPS assembly is designed to accommodate vertical or
horizontal truss/pole mounting. For horizontal pole mounting,
proceed to Horizontal Installation section. To use the TPS in
the vertical configuration, proceed to Vertical Installation
section.
Vertical Installation
1. Verify truss plate (B) is properly oriented for installation.
(See Figure 1)
Figure 1
2. Securely anchor truss plate (B) to pole using Chief TPK
clamp kit (not included) following instructions and using
hardware included in kit. (See Figure 2) and (See Figure 3)
Figure 2
NOTE: The orientation of the truss plate (B) when mounted on
a truss is the same as when mounted on a pole. The
number of clamps required will depend on the number
of trusses used for installation. (See Figure 3)
NOTE:
Figure 3
3. Position faceplate (A) in front of truss plate ensuring the
mounting studs face the truss plate. (See Figure 4)
Figure 4
Slot at
Recessed, slotted flat
(B)
bottom
surface against pole
1
1
Vertical
pole
(B)
TPK clamp kit
(not included)
2
x 4
(B)
Trusses used (2) (example)
TPK clamps x 4
(not included)
x 8
2
To Display
Side with mounting studs towards truss plate (B)
To
Trusses
Note: Trusses/poles
not shown for clarity.
(B)
(A)
3
or poles
Installation Instructions TPS Series
7
4. Align mounting studs on faceplate (A) with center upper
mounting hole and lower center slot in truss plate (B).
5. Install two 1.055" x .406" x.250" Nylon spacers (D) onto
mounting studs on TPS faceplate (A). (See Figure 5)
6. Place the two mounting studs on faceplate through center
upper mounting hole and lower center slot in truss plate (B).
7. Secure top of TPS faceplate (A) to truss plate (B) using one
3/8" flat washer (E), and one 3/8" Stover lock nut (C). (See
Figure 5)
Figure 5
8. Secure bottom of TPS faceplate (A) to truss plate (B) using
one .094" washer (F), one 3/8" flat washer (E), and one
3/8" Stover lock nut (C). (See Figure 5)
9. Proceed to Display Installation section.
Horizontal Installation
1. Rotate the truss plate (B) 90° and verify it is properly
oriented for horizontal mounting. (See Figure 6)
Figure 6
2. Securely anchor truss plate (B) to horizontal pole using
Chief TPK accessory clamps (not included) following
instructions included with TPK clamp kit. (See Figure 7)
Figure 7
Mounting Studs
(D) x 2
(A)
(B)
(E) x 2
(F) x 1
(C) x 2
Note: Trusses not shown for clarity.
(x 2)
5
7
8
4
1
Lower center slot
Recessed, slotted flat surface
against pole
(B)
Horizontal
TPK clamps (not provided)
2
Installation
x 4
(B)
TPS Series Installation Instructions
8
3. Secure top of faceplate (A) to the truss plate (B) using one
3/8" flat washer (E) and one 3/8" Stover lock nut (C). (See
Figure 8)
4. Secure bottom of TPS faceplate (A) to the truss plate (B)
using one .094" washer (F), one 3/8" flat washer (E) and
one 3/8" Stover lock nut (C). (See Figure 8)
Figure 8
DISPLAY INSTALLATION
WARNING: Exceeding the weight capacity can result
in serious personal injury or damage to equipment! It is
the installer’s responsibility to make sure the combined
weight of all components attached to the TPS does not
exceed 150 lbs (68.04 kg).
IMPORTANT ! : Make sure no power is supplied to the
display and the latching flag on the TPS is in the
unlocked position before attempting to attach the display.
(See Figure 9)
Figure 9
1. Attach interface bracket (G) to display using the instructions
included with the interface bracket kit.
2. Lift and maneuver display such that all mounting buttons fit
into mounting slots on TPS faceplate (A). (See Figure 10)
Figure 10
3. Lower display firmly into place. Ensure each button has fully
seated in its mounting slot. (See Figure 10) and (See
Figure 11)
Figure 11
Horizontal
3
Installation
(C)
(D) x 2
(F) x 1
(E) x 2
4
(C)
Unlocked
Locked
Mounting
2
slot
(A)
Mounting button
3
(A)
Mounting slots (x4)
Display
3
Note: Trusses not
shown for clarity.
Installation Instructions TPS Series
9
4. With the mounting buttons of the display fully engaged in
the slots of the TPS (A), secure display to the TPS by raising
the Q-Latch flag all the way up to the locked position. (See
Figure 12)
NOTE: If Q-Latch flag does not fully engage, ensure the
mounting buttons are fully seated in the lower part of
the mounting slots.
Figure 12
5. Attach all cables to display.
Adjustments
The TPS mount provides for limited roll adjustment to level the
display after installation.
To adjust display roll:
1. Loosen the two roll adjustment nuts in upper and lower
center holes of truss plate. (See Figure 13)
2. Level the display as desired.
3. Tighten the two roll adjustment nuts. (See Figure 13)
Figure 13
Locked
4
(A)
Mounting
Display
buttons in
slots (4)
2 deg.
View from back
Note: Mounting structure and hardware not shown for clarity.
(A)
(B)
1
3
x 2
x 2
TPS Series Installation Instructions
10
Removing the Display
WARNING: IMPROPER HANDLING CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate support
of display while removing it may cause display to fall! Watch
for pinch points. Do not put your fingers between movable
parts.
IMPORTANT ! : Ensure Q-Latch flag securing display is
completely raised at all times except when removing or
installing display. The flag must be all the way up when
installing or removing cables.
1. With display securely supported, unlock display from TPS
(A) by lowering the Q-Latch flag all the way down to the
unlocked position. (See Figure 14)
Figure 14
2. Using two people, slide display up and out of TPS (A).
(Optional) Security Lock
A hole is provided in the Q-Latch flag and TPS faceplate (A) to
accommodate the insertion of a padlock or similar locking
device.
1. Insert padlock (not included) through lower (lined up) holes
of Q-Latch flag and TPS faceplate (A). (See Figure 15)
Figure 15
(A)
Unlocked
1
(A)
1
Q-Latch flag
(A)
Display
Installation Instructions TPS Series
11
TPS Series Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002567 Rev00
2014 Milestone AV Technologies
www.chiefmfg.com
04/14
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Chief TPS2642 Manuel utilisateur

TPS2642
Chief
Marque
Chief
Modèle
TPS2642
Catégorie
Mur
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes