Q Acoustics M2 Soundbase Manuel utilisateur

1

Qm2

MANUAL

2

3

Important safety information and warnings

Introduction

Package contents

Feature summary

Product description

Use scenarios

Features

Top panel

Front

Rear panel

Remote control

Operating Q Acoustics Unit

On / In / Wall EQ

Power and standby

Intelligent Pre-Amplifier (IPA™)

Auto On / Off

Auto On / Off Times

Auto source select

Low source gain (LSG™)

Source volume control

Bluetooth®

MoviEQ™

Lip Sync

Cable / satellite remote control

Specification

Warranty

Contents

4

6

7

8

9

10

15

16

20

22

23

4

Important Safety Information and Warnings

1 Notices

1.1 FCC Statement (For US Customers)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

1.2 FCC Radiation Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with a minimum distance of 8 in/20cm between the radiator and your body.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

CAUTION! Any changes or modifications made to this device that are not expressly approved by Q Acoustics may void the user’s

authority to operate the equipment.

1.3 Industry Canada Statement (for Canadian Customers)

CAN ICES-3 (B)/NMB-3(B)

The device meets the exemption from the routine evaluation limits set out in section 2.5 of RSS 102 and is in full compliance with

RSS-102 RF. Users can obtain information on RF exposure

and compliance from Industry Canada.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired operation.

1.4 Bluetooth®

This unit contains a Class 2 Bluetooth® transmitter working at 2.4GHz.

2 Safety Information and Warnings

2.1 Instructions

Read and understand these instructions before you use your Soundbar. If damage is caused by failure to follow these instructions,

the warranty does not apply. Please keep these instructions in a safe place.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers that produce

heat.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they

exit from the apparatus.

Only use attachments/accessories specifie by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table specifie by the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualifie service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

2.2 Installation

• The mains plug is the means of disconnecting the unit from the mains supply and shall be readily accessible.

• Only use the accessories supplied with the unit.

5

• To prevent injury,this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

• Never install this product in a confined space. Always leave a space or at least four inches around the product for ventilation.

• The ventilation should not be impeded by covering the ventilation openings with items,such as newspapers,table-cloths,curtains,etc.

• Do not place any sources of danger on the apparatus (for example: liquid filled objects, lighted candles).

• The use of apparatus is in tropical and/or moderate climates.

2.3 Moisture

• To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain, moisture, dripping or splashing.

• Do not use this apparatus near water.

2.4 Remote Control Battery

The remote control supplied with this unit contains a coin/button cell battery. To prevent battery leakage which may result in bodily

injury, property damage, or damage to the unit:

• Install the battery correctly, + and - as marked on the unit.

• Remove the battery when the unit is not used for a long time.

• Do not expose the battery or remote control to excessive heat, including sunshine.

• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• WARNING - DO NOT INGEST BATTERY - CHEMICAL BURN HAZARD.

• If the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries

away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you

think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention

Disposal of Batteries

The battery supplied contains perchlorate material and in many areas batteries may not be disposed of with your household waste.

Please ensure you dispose of batteries according to local regulations.

The battery supplied does not contain the heavy metals mercury or cadmium.

2.5 Servicing

Servicing is required when the unit or mains cord has been damaged in any way, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, it does not operate normally, or has been dropped.

Refer all servicing to qualified service personnel.

3.0 Symbols used on this product

Class II Equipment Symbol

High Voltage Hazard Symbol

Hazard Warning Symbol

Waste Electrical and Electronic

Equipment Symbol

This symbol indicates that the unit has a Class II double insulation system,

and no protective earth provided.

This symbol indicates uninsulated material within your unit may cause an

electrical shock. For the safety of everyone in your household, please do

not remove the product covering.

The ‘exclamation mark’ calls attention to features for which you should

read this manual closely to prevent operation and maintenance problems.

WARNING: To reduce the risk of fire or electric shock, this apparatus

should not exposed to rain or moisture and object filled with liquids, such

as vases, should not be placed on this apparatus.

CAUTION: To prevent electric shock, match wide blade of plug to wide

slot, fully insert.

This symbol indicates that when the unit is to be discarded, it must

be separated from other household-type waste and sent to separate

collection facilities for recovery and recycling of electrical and electronic

equipment.

Please make sure you are familiar with your local rules on the separate

collection of electrical and electronic products.

6

Thank you for purchasing Q Acoustics.

This manual is intended to take you through the setup and installation of the M2. It will help provide a trouble

free setup and optimum performance from the product.

Please read the instructions, important safety information and warnings carefully before installation and use,

to ensure the safe and satisfactory operation of this product.

We hope you enjoy the Q Acoustics experience.

Introduction

Package Content

SOURCE

EQ

QUICK START GUID E QUICK START GUID E

WARRANTY

1 x Q m2 Soundbar

1 x Remote Control

1 x Quick Start Guide 1 x SAFETY

INFORMATION

1 x Warranty Card

1 x Mains Cable

(Regional mains cable)

1 x HDMI Cable

7

IPA™ – Q Acoustic’s Intelligent Pre-Amplifier removes the need for a remote control through a

signal sensing matrix to enable auto source selection and auto on/off.

MoviEQ™ – Q Acoustic’s Movie EQ helps to maximise the drama and excitement of a movie or

TV soundtrack. Toggle it on or off for music and movie settings.

NFC – Near Field Connection allows simple connection of Bluetooth® devices by tapping the

NFC location on the Q Acoustics speaker.

HDMI ARC – High Definition Multimedia Interface Audio Return Channel removes the need for

additional Optical or Analogue audio cables between source and speaker.

CEC – Consumer Electronics Control syncronises TV remote control of Volume, Mute and

Standby for easy integration of our Q Acoustics speaker.

Bluetooth® – An international wireless connection used for streaming audio from all compatible

devices.

aptX™ – A high definition audio CODEC used for Bluetooth® streaming.

AVRCP – A Bluetooth control protocol that synchronises your device control of Volume and

Mute for easy integration of our Q Acoustics speaker.

DAC – Digital to Analogue Converter which determines the bit depth and sample rate of the Q

Acoustics speaker; the higher the number, the better the audio quality.

BMR – Balanced Mode Radiators are Q Acoustics mid/high driver of choice, they have a flat

radiating surface which enables their dispersion to fill a room with sound.

DVC – Dual Voice Coil subwoofers are Q Acoustics subwoofer driver of choice, it has two voice

coils in one driver for greater flexibility of design and improved bass control.

Sub Out – A Phono subwoofer output for connection to an external subwoofer. On some of

our older products the additional sub out provides a huge bottom end when used with a Q

Acoustics subwoofer.

Dynamic Bass – Improved response, loudness, depth and control of bass frequencies is

achieved through our dynamic bass enhancement system, to perfectly integrate our inbuilt

DVC subwoofer.

User EQ – User control of EQ setting for best acoustic performance. This can be changed

dependent upon speaker position, mounting, or user preference.

LSG™ –Q Acoustic’s Low Source Gain switch increases the incoming signal level to get

maximum performance from your system when connected to low output signal equipment via

HDMI or Optical.

Power Rating – Total continuous power rating of the system in Watts. Eg. BT3 = 2 x 50W =

100W.

Lip Sync – Adjustable delay for lip synchronisation between TV/screen and Q Acoustics

speaker.

3.5mm – 3.5mm jack socket for Analogue input.

RCA – Stereo phono socket for Analogue input.

Feature summary

8

The Qm2 is simplicity redefined; where beautifully engineered sound meets beautiful design.

This is an elegantly compact soundbar with a big heart to fill your living room without the clutter of a full Hi-Fi

system or even a soundbar with a large external subwoofer.

Q Acoustic’s new Intelligent Pre-Amplifier (IPA™) is designed to seamlessly integrate into your home setup.

The Qm2 is a true plug and play soundbar. Connect it to your television using the ARC HDMI input and

forget about it. The Qm2 becomes one with your TV, leaving you to discover both sides of this unique

product, Music and Movies.

Turn on the Qm2 and Music mode is enabled by default. Our built in aptX® Bluetooth® wireless input

frees the world of music at your fingertips to fill your home with superbly detailed and dynamic audio

reproduction. Discover subtle layers in your music that have been left previously unheard and enjoy music

as was intended!

Switch on the TV and the Qm2 automatically brings clarity of speech and a depth of soundscape that

transforms your TV sound… and when you engage the MoviEQ™ your home will rumble with powerful bass

and dynamics for that full blooded movie experience!

Product description

9

Use scenarios

Important Cautions:

• Q Acoustics accepts no liability for damages caused by incorrect assembly, installation or improper use.

• If you choose to place your TV ontop of this soundbar please do so with caution. The TV base must not

extend over the sides of the soundbar and the TV must sit in the centre of the Qm2.

• For best performance it is recommended that this product is used ontop of an AV stand or inside a cabinet.

Please see illustrations below.

• Do not exceed the maximum TV weight limit of 25kg when placing a TV ontop of the Qm2.

10

a. Deep standby / Standby / Source select

5s press / 2s press / 1s press

b. Volume Down

Single press / press and hold

c. Volume Up

Single press / press and hold

d. Status LED

See LED indications below

e. NFC Pairing Position

Removable sticker

a. IR Sensor

The IR sensor is hidden behind the speaker grille in the centre towards the top of the Unit.

This sensor MUST be unobstructed for direct line-of-sight to the remote, or the remote will not be able to control the Unit.

No Light = Off

Power cord is disconnected.

Dim Red = Off (DEEP STANDBY)

Power cord is connected and the Unit is in DEEP

STANDBY.

Solid Red = Off (STANDBY)

Power cord is connected and the Unit is in STANDBY.

Solid Purple = On

HDMI input is the active source.

Solid White = On

Optical input is the active source.

Solid Blue = On

Bluetooth® input is the active source and is Paired

with a Bluetooth® device.

Quick Blue Flash = On

Bluetooth® input is the active source and is currently

searching for a Bluetooth® device to Pair with.

Solid Green = On

Analogue input (Line in 1 or Line in 2) is the active

source.

Yellow = MoviEQ™

MovieEQ™ setting is toggled between On / Off.

Any Colour Slow Flash = On

Currently active source is MUTED.

1. Top Panel

2. Front

Features

b a d c

e

a

11

a. Bluetooth® Pair Button

b. HDMI™ (ARC) Input

c. Digital Optical Input

d. Analogue Line In 1

e. Analogue Line In 2

f. AC Mains Input

g. USB for Service Only

3. Rear Panel

a

fb c deg

a. Bluetooth® Pair Button

The Bluetooth® Pair button is used to manually drop any current Bluetooth® connection and make the

Unit Discoverable by a new device.

Device Settings

MY DEVICES

Q M2 Connected

12

b. HDMI (ARC)

HDMI™ (ARC) is for connection to the Audio Return Channel (ARC) output on a TV or other source. If there

is a choice between HDMI™ or Optical connection to the Unit choose HDMI to enable Consumer Electronic

Control (CEC). When the HDMI source is active the status LED will be PURPLE.

Important Note: Audio output of a TV, Blu-ray disc player, games console, or DVD player connected to the

Unit via HDMI, must be set to PCM (two channel stereo) in the source setup.

c. Optical Input

Optical In is for connection to the Digital Optical output on a TV or other source. If there is a choice between

Digital or Analogue connection to the Unit choose Digital for superior audio quality. When the Digital Source

is active the status LED will be WHITE.

Important Note: Audio output of a TV, Blu-ray disc player, games console, or DVD player connected to the

Unit via Optical Digital, must be set to PCM (two-channel stereo) in the source’s setup. Digital connection

to a CD player does not require a special setting.

HDMI

Audio Return Channel

(ARC)

AUDIO OUT

Digital - Optical

13

d. Analogue Inputs Line In 1

The Unit has two options for Analogue audio connection. The Status LED will be GREEN when an Analogue

input is in use.

e. Analogue Inputs Line In 2

Connect the RCA L&R audio output from a TV or other source to the LINE IN 2 sockets using a Phono

RCA cable.

Important Note: With a jack plugged into LINE IN 1, LINE IN 2 is switched-off and no audio will be heard

from this source.

Please Note: When connecting to a variable level source, such as a headphone output, better audio quality

will be achieved by having the source set at a higher volume level and the Unit at a lower level, than the

other way around.

AUDIO OUT

Headphones

AUDIO OUT

Analogue

14

f. AC Mains Input

Universal power connector automatically selects AC voltage for a given region. Connect to the included AC

Mains Cable for your country.

Important Note: Always remove the AC Mains Cable when making connections to the Rear Panel.

g. USB for Service Only

Universal Serial Bus (USB) for service only. This USB port will not provide 5V power, and cannot be used

for anything other than Service Updates.

AC MAINS

Regional mains cable

15

a. Power

Press this button to turn the Unit STANDBY ON/OFF.

b. Source select

Press this button to manually select the audio input source.

The status LED will change colour accordingly.

Important Note: When the Source button is used, the Unit

will stay on the selected source and disable the Intelligent Pre-

Amplifier (IPA) automatic source selection. IPA functions will be

reactivated after the Unit has been put in STANDBY.

c. Volume Up / Down

Press VOL + to increase the volume. Press VOL – to reduce

the volume.

d. Mute

Press this button once to MUTE the Unit. Status LED will

SLOW FLASH to indicate MUTE. Press this button again to

un-mute the Unit.

Please Note: Long press of Mute will also put the Unit into

STANDBY.

e. EQ

Short press the EQ button to toggle MoviEQ™ On and Off. If

the Yellow LED flashes and remains on, MoviEQ™ is On.

Caution: When replacing the lithium battery in the remote, make sure that the replacement battery is

inserted with the correct polarity. Place the battery so that the positive (+) side faces up with the tray held so

the surface with the dot and (+) is facing up.

Remote Control battery replacement

a. Push small tab

toward battery slot.

b. Pull battery

drawer out.

c. Insert battery

with “+” side up

and slide drawer

back into remote.

d. Slide drawer

back into remote.

Caution: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent battery type (CR2025)

Warning: Do not expose batteries to excessive heat such as direct sunlight, fire or the like.

Dispose of dead batteries in accordance with local regulations.

4. Remote control

a

b

c

d

e

16

1. On / In+ / In-

This EQ switch should be the first thing you set on your Unit. The Unit has been voiced by our acoustic

experts to get the best audio performance possible for the three most common placements within a

room.

Simply select the placement that best fits your living environment using the switch on the Rear Panel, and

let Q Acoustics handle the rest.

ON = On a cabinet

IN+ = In a large cabinet

IN- = In a small cabinet

2. Power and standby

With the AC Mains turned off, plug in the AC Mains Cable. Once all Rear Panel audio connections are

made, turn the AC Mains ON. The speakers will enter STANDBY, and show a RED status LED.

Exit STANDBY by turning a connected source ON, or by pressing the STANDBY button on either the Top

Panel or the IR remote. The LED will then change colour according to the AUTO SOURCE SELECT rules.

If NO input signals are detected, the Unit will select the Analogue input and then automatically enter

STANDBY after 20 minutes.

3. Intelligent Pre-Amplifier (IPA™)

In normal operation the IPA™ will be active.

Q Acoustics IPA™ is designed so the user requires the minimum amount of effort to get full functionality.

The IPA™ will AUTO ON/OFF and AUTO SOURCE SELECT according to our carefully designed

intelligence matrix.

4. Auto On / Off

When connected to an audio source, the Unit has an AUTO ON function and will come out of STANDBY

when it detects an active audio signal is connected.

When the audio signal is stopped for a pre-defined period of time, the Unit has an AUTO OFF function

and will go into STANDBY.

This, for example, allows easy integration of the Unit with your TV, automatically turning ON and OFF in

synchronisation with your TV STANDBY control.

5. Auto On / Off Times

5.1. HDMI™

• ON time is determined by the CEC response time of your TV; it can take between 0-10s.

• OFF time is determined by the CEC response time of your TV; it can take between 0-5s.

5.2. Optical

• ON time is immediate once the red Optical light from your source comes on.

• OFF time is immediate once the red Optical light from your source turns off.

Please Note: Some televisions continue their optical output when the TV is in STANDBY. The Unit will not

AUTO OFF under these circumstances and the STANDBY control must be used.

Operating Q Acoustics Unit

17

5.3. Bluetooth®

• ON time is determined by the AVRCP response time of your Bluetooth® device; once your device is

connected, and you press Play it can take between 1-5s.

• OFF time is determined by the AVRCP response time of your Bluetooth® device. Once you turn

Bluetooth® off, or disconnect your device it can take between 1-3s.

5.4. Line In 1 / 2

• ON time is determined by the audio signal level; when the signal level is audible it can take between

1-3s.

• OFF time is determined by the audio signal level; when the signal level is not audible it will take 20

minutes.

Please Note: If the user places the Unit in STANDBY while a source is still playing, the AUTO ON function

will be disabled until the source is stopped. This will prevent the Unit from unwanted AUTO ON.

For Line In 1/2 the signal must be at a not audible level for 20 minutes before the Unit AUTO ON will

function.

6. Auto source select

Optical input

HDMI™ ARC

Bluetooth®

Line in 1

Line in 2

Standby

INPUT

PRIORITY

The IPA™ follows a priority list for connected audio sources. A connected HDMI™ source that starts to play

has the highest priority, followed by Optical, then Bluetooth® and finally Analogue 1 and 2:

Important Note: The IPA™ can be overridden at any time by a simple manual SOURCE SELECTION from

the user. Simply press the SOURCE SELECT button on the remote, or a short press of the STANDBY

Button on the Unit.

The IPA™ will reactivate once the Unit has been put into STANDBY.

7. Low source gain (LSG™)

During our extensive testing we found that on a number of manufacturer’s equipment the digital signal

output level is lower than the expected Full Scale (FS). To allow our users to get the best audio experience

from the Q Acoustics Unit we have included a LSG™ switch.

The LSG™ switch can be found on the Rear Panel, and has two settings.

1 = Normal gain

2 = Increased 6dB of gain for Optical and HDMI™ sources

18

You should first listen to your setup with LSG™ = 1

If you find your signal level to be quite low from your TV/DVD player/Music source, please select LSG™

= 2.

Please Note: You will not require the LSG™ if you are using a Streamer/CD player Optical output. Hi-Fi

audio equipment will output FS digital audio. Audio will be highly distorted if you have LSG™ = 2 in this

scenario.

8. Source volume control

Audio sources will initially be set at a DEFAULT volume level. The volume can be adjusted separately for

each source using the VOL + and VOL – buttons on the Top Panel or IR remote. Once adjusted, the IPA™

will remember the new volume level for the currently selected source, and will return to that level each

time that source is re-selected.

9. Bluetooth®

9.1. Pairing a Bluetooth® device

The unit is designed to be Discoverable when in STANDBY, to allow AUTO ON. It is also designed to

automatically go into Pairing mode if there is no Bluetooth® device connected. To Pair your Bluetooth®

source:

1. Connect the AC Mains Cable to the Unit and switch ON.

2. Make sure Bluetooth® is enabled on the device to be Paired. The Bluetooth® controls are typically

found in the device’s ‘Settings’ or ‘Connections’ menu.

3. On your device’s list of discoverable devices, you should now see ‘Q M2’.

4. Select ‘Q M2’ and your device will now be Paired via Bluetooth® and Connected.

5. From within the music player on your device, select ‘Q M2’ as the audio output and press Play. Unless

the remote has been used to manually select another source and override the IPA™, or a higher priority

source is active, the Unit will switch to Bluetooth® input and the LED will turn Blue.

9.2. Pairing a Bluetooth® device with NFC

1. Connect the AC Mains Cable to the unit and switch ON.

2. Make sure Bluetooth® and NFC are enabled in the device settings.

3. Place NFC device on the top surface of the Unit, in the location indicated.

Please Note: You may need to rotate your device for NFC to connect, as NFC coils are in different

locations within different devices. Please see your device instruction manual for correct NFC operation.

The distance needed for successful NFC Pairing can vary from device to device.

4. The NFC device will automatically register on screen when an NFC connection has been made.

5. Follow on-screen instructions to complete NFC Pairing. This usually involves selecting to allow NFC

Pairing.

6. Your device will now be Paired, and Connected via Bluetooth®, and will function as any other Bluetooth®

source when pressing Play from within the device music player.

Please Note: Although starting to Play a track on the connected source will cause the Unit to switch to

Bluetooth®, the Unit will stay on Bluetooth® until the source is Disconnected. It will not switch to a lower

priority source whilst the player is Paused.

Please Note: The IPA™ will switch to Bluetooth® the first time a connected device sends any audio signal,

including message alerts, notification and key press effects.

Please Note: When Connected, the device’s volume and mute buttons will control the Unit using AVRCP.

You will also notice that if you switch away from the Bluetooth® source, your currently playing track will

PAUSE for you.

Not all Bluetooth® devices are AVRCP compatible.

19

9.3. Going out of range

When a Connected device goes out of range, the Unit will remain on the Bluetooth® channel. When the

device returns in range it will automatically re-connect to the Unit. In many cases Play must be pressed

on the device to resume audio playback. Whilst out of range, the Unit source can still be changed using

the SOURCE SELECT button or by turning on a higher priority source.

Please Note: If the Bluetooth® source does not come back into range for 20 minutes the Unit will

automatically go into STANDBY.

9.4. Pairing more than one Bluetooth® device

The Unit can have up to eight Bluetooth® devices in its Pairing list. When you Pair with the 9th device the

details of the first device will be lost.

Once the Unit is connected with a device, it will stop automatically searching for other devices to Pair with

or Connect to. To Connect to another device, either Disconnect the currently connected source on the

device itself or press the Bluetooth® Pair button on the Rear Panel of the Unit.

9.5. Coming out of standby

If there is a Paired device in proximity to the Unit when it comes out of STANDBY it will automatically

initiate a connection to the device. It will not switch to Bluetooth® input until Play is pressed on the device.

10. MoviEQ™

MoviEQ™ is Q Acoustics’ preferred balance to maximize the excitement and drama from your TV and

Movie viewing.

MoviEQ™ is simply toggled On or Off by pressing the Remote Control EQ button. The LED will indicate

whether MoviEQ™ is turned on by a flash pattern shown below:

Yellow flash x 2 + yellow = MoviEQ™ On

Yellow flash x 2 + red = MoviEQ™ Off

11. Lip Sync

The Unit has a lip sync feature for its HDMI™ and Optical inputs. This allows up to 50ms of delay to be

added to the audio for synchronisation with a screen. When in Lip Sync mode, the lip sync is adjustable

in 10ms steps using the Vol + and – buttons.

To enter Lip Sync mode simply double tap the Bluetooth® Pair button on the Rear Panel of the Unit.

The lip sync time is then adjusted and displayed by the following flash pattern, the LED will maintain the

colour of the currently selected source:

0ms = 2 flash

10ms = 4 flash

20ms = 6 flash

30ms = 8 flash

40ms = 10 flash

50ms = 12 flash

After 30 seconds of no other button presses the Unit will exit Lip Sync mode and return to normal

operation. You will only have to set the Lip Sync once as the Unit remembers the delay times for both

HDMI™ and Optical separately.

20

• Press the “TV” button (top left of remote).

• Point remote away from receiver,

press and hold “Select + 0”.

• The remote’s LED will flash red twice.

• Enter “1217”. The remote’s LED will flash

red twice to confirm correct code.

• Press and hold “Select + 1”.

• The remote’s LED will flash red twice.

• Press TV and your remote controls will now work

as below:

Button Function

Vol + Volume up

Vol - Volume down

Mute (short press) Mute

or Mute (long press) Standby

Source select

TYPE 1 (SATELLITE)

TV

1

+

23

6

5

4

789

0

SELECTVOL

MUTE

Volume up / down

Mute / Standby

Standby

Source select

The Q Acoustics system has been designed for easy integration into your home entertainment system as it

has the ability to be controlled by many types of PROGRAMMABLE REMOTE CONTROL. This may include

the remote control for your SATELLITE and CABLE system if it has PUNCH THROUGH capability. Punch

through is the common term for being able to program your remote control to send IR codes to both a TV

and an AV Preamplifier/Processor. To use punch through you normally select the TV you wish to support

first, and then the AV Preamplifier/Processor.

The Unit uses the PHILIPS RC5 protocol for AV Preamplifiers/Processors. Programming your remote with

PHILIPS AV codes should allow you to control volume and mute of your Unit. In some cases you may also

be able to control STANDBY and SOURCE SELECT with buttons such as and .

Manufacturers often offer several PHILIPS code options for their remote controls. We recommend that you

work through the PHILIPS code list for your remote and experiment with each one until you find one that

works well with the Unit. It is easiest to recognise when one is working by pressing the volume up/down

buttons.

We cannot guarantee that the Unit will work with your particular remote as the IR codes it sends are outside

our control, however by supporting the commonly used Philips standard we hope to have made it as easy

as possible to gain control of your device with the remote control of your choice.

Below we show how two typical programmable remote controls can be set up.

Cable / satellite remote control

La page charge ...

Q Acoustics M2 Soundbase Manuel utilisateur

Q Acoustics M2 Soundbase Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents