YOTRIO Byward 4 Piece Conversation Set – Chair Assembly Instructions

Marque: YOTRIO

Modèle: Byward 4 Piece Conversation Set – Chair

Catégorie: Cuisinières

Taper: Assembly Instructions

BYWARD 4 PIECE

CONVERSATION SET - CHAIR

IMPORTANT: Please read this manual carefully before beginning assembly of this product.

Keep this manual for future reference.

Made in China. Imported by Trileaf Distribution Trifeuil Toronto, Canada, M4S 2B8

Warning! To reduce the risk of serious injury, read the following safety

instructions before assembling and using the chair.

• This product is intended for domestic, outdoor use only.

• The product should be placed on ﬂat, horizontal ground.

• Any assembly or maintenance of the product must be carried out by adults only.

• Arrange necessary manpower when assembling or moving the product.

• Some parts may contain sharp edges. Wear protective gloves if necessary.

• Check all nuts and bolts periodically for tightness. When required, tighten them again.

• If the product will not be used for a long period of time (e.g., wintertime), it should be

stored in a clean, dry environment.

• Do not light any ﬁres inside or near the product!

• Do not hang any weights on the frame.

• Retain the original package to store the product.

RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.

2 people

• Do not place the product underneath electrical lines.

• Keep children away during assembly.

• This product contains small parts which can be swallowed by children.

• Keep ﬁngers away from places where they can be pinched or trapped.

1-888-670-6684

If you have questions regarding your product, require warranty assistance,

or have damaged or missing parts, please call our customer service toll-free

helpline. Contact us for assistance; we're here to help.

Please read and understand this manual before any assembly. Before beginning

assembly of product, make sure all parts are present. Compare parts with packaging contents list.

If any part is missing, or if you have any questions, contact the service centre at

1-888-670-6684 (toll free).

Place all parts from the box in a cleared area and position them on the ﬂoor in front of you. Remove

all packing materials and place them back into the box. Do not dispose of the packing materials until

assembly is complete. Read each step carefully before beginning any assembly and make sure you

understand each step.

Needed for assembly:

Chair frame -

Front leg -

Rear leg -

Back cushion -

Seat cushion -

M6x20 Combination bolt and washer -

Hex key -

Requires

Place the chair frame (A) upside down on a soft, ﬂat surface. Connect

the front legs (B) to the bottom of the chair frame (A) by aligning the

holes. Insert M6x20 combination bolt and washer (AA). Lightly tighten

the bolts using the hex key (BB). Do not completely tighten until all

assembly is completed. Repeat the same step for rear legs (C).

Your chair is now ready to use.

Requires

Ensure all bolts are securely tightened using the hex key (BB). Turn the chair to the

upright position and place back cushion (D) and seat cushion (E) on the chair as shown.

Do not completely tighten.

CLEANING AND MAINTENANCE

• Check all screws and nuts periodically for tightness, tightening them

again as required.

• Disassemble the chair in the reverse order of the assembly steps.

• Always disassemble the chair completely. A partially disassembled

chair is not stable enough to resist wind and bad weather, and therefore

can be damaged and/or cause damage.

• Clean the chair with mild soap and water. Rinse thoroughly, and wait

until the chair is completely dry before reassembling it.

• Always use a mild soap—never detergent.

- Water should be cold to lukewarm—never more than 25°C (77°F).

• Steel components of garden accessories and furniture are treated with

rust-inhibiting paint. However, due to the nature of steel, surface oxidation (rusting)

will occur if this protective coating is scratched. This is a natural process. To minimize

this condition, it is recommended that care be taken when assembling and handling

the product in order to prevent the paint from being scratched. Surface rust can be

removed easily using a very light application of common cooking oil. If surface

oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may

start dripping onto the assembly surface, which may cause damaging stains that may

be di cult to remove.

Dimensions (L x W x H)

Product weight

Weight capacity

This CANVAS product carries a one (1) year warranty against defects in

workmanship and materials. Trileaf Distribution agrees to replace a

defective product free of charge within the stated warranty period, when

returned by the original purchaser with proof of purchase. This product is

not guaranteed against wear or breakage due to misuse and/or abuse.

31 1/8 x 29 3/4 x 30 1/8"

79 x 75.5 x 76.5 cm

23 lb 2 oz

10.5 kg

250 lb

113.39 kg

SPECIFICATIONS

BYWARD 4 PIECE

CONVERSATION SET

- LOVESEAT

IMPORTANT: Please read this manual carefully before beginning assembly of this product.

Keep this manual for future reference.

Made in China. Imported by Trileaf Distribution Trifeuil Toronto, Canada, M4S 2B8

Warning! To reduce the risk of serious injury, read the following safety

instructions before assembling and using the loveseat.

• This product is intended for domestic, outdoor use only.

• The product should be placed on ﬂat, horizontal ground.

• Any assembly or maintenance of the product must be carried out by adults only.

• Arrange necessary manpower when assembling or moving the product.

• Some parts may contain sharp edges. Wear protective gloves if necessary.

• Check all nuts and bolts periodically for tightness. When required, tighten them again.

• If the product will not be used for a long period of time (e.g., wintertime), it should be

stored in a clean, dry environment.

• Do not light any ﬁres inside or near the product!

• Do not hang any weights on the frame.

• Retain the original package to store the product.

RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.

2 people

• Do not place the product underneath electrical lines.

• Keep children away during assembly.

• This product contains small parts which can be swallowed by children.

• Keep ﬁngers away from places where they can be pinched or trapped.

1-888-670-6684

If you have questions regarding your product, require warranty assistance,

or have damaged or missing parts, please call our customer service toll-free

helpline. Contact us for assistance; we're here to help.

Please read and understand this manual before any assembly. Before beginning

assembly of product, make sure all parts are present. Compare parts with packaging contents list.

If any part is missing, or if you have any questions, contact the service centre at

1-888-670-6684 (toll free).

Place all parts from the box in a cleared area and position them on the ﬂoor in front of you. Remove

all packing materials and place them back into the box. Do not dispose of the packing materials until

assembly is complete. Read each step carefully before beginning any assembly and make sure you

understand each step.

Needed for assembly:

Loveseat frame -

Front leg -

Rear leg -

Back cushion -

Seat cushion -

M6x20 Combination bolt and washer -

Hex key -

Requires

Place the loveseat frame (A) upside down on a soft, ﬂat surface.

Connect the front legs (B) to the bottom of the loveseat frame (A) by

aligning the holes. Insert M6x20 combination bolt and washer (AA).

Lightly tighten bolts using hex key (BB). Do not completely tighten

until all assembly is completed. Repeat the same step for rear legs (C).

Your loveseat is now ready to use.

Requires

Ensure all bolts are securely tightened using the hex key (BB). Turn the loveseat to the

upright position and place back cushions (D) and seat cushion (E) on the loveseat as

shown.

Do not

completely tighten.

• Check all screws and nuts periodically for tightness, tightening them

again as required.

• Disassemble the loveseat in the reverse order of the assembly steps.

• Always disassemble the loveseat completely. A partially disassembled

loveseat is not stable enough to resist wind and bad weather, and

therefore can be damaged and/or cause damage.

• Clean the loveseat with mild soap and water. Rinse thoroughly, and wait

until the loveseat is completely dry before reassembling it.

• Always use a mild soap—never detergent.

- Water should be cold to lukewarm—never more than 25°C (77°F).

• Steel components of garden accessories and furniture are treated with

rust-inhibiting paint. However, due to the nature of steel, surface oxidation (rusting)

will occur if this protective coating is scratched. This is a natural process. To minimize

this condition, it is recommended that care be taken when assembling and handling

the product, in order to prevent the paint from being scratched. Surface rust can be

removed easily using a very light application of common cooking oil. If surface

oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may

start dripping onto the assembly surface, which may cause damaging stains that may

be di cult to remove.

Dimensions (L x W x H)

Product weight

Weight capacity

This CANVAS product carries a one (1) year warranty against defects in

workmanship and materials. Trileaf Distribution agrees to replace a

defective product free of charge within the stated warranty period, when

returned by the original purchaser with proof of purchase. This product is

not guaranteed against wear or breakage due to misuse and/or abuse.

55 1/8 x 31 1/8 x 30 1/8"

140 x 79 x 76.5 cm

37 lb 8 oz

17 kg

250 lb per seat

113.4 kg per seat

CLEANING AND MAINTENANCE

SPECIFICATIONS

BYWARD 4 PIECE

CONVERSATION SET - TABLE

IMPORTANT: Please read this manual carefully before beginning assembly of this product.

Keep this manual for future reference.

Made in China. Imported by Trileaf Distribution Trifeuil Toronto, Canada, M4S 2B8

Warning! To reduce the risk of serious injury, read the following safety

instructions before assembling and using the table.

• This product is intended for domestic, outdoor use only.

• The product should be placed on ﬂat, horizontal ground.

• Any assembly or maintenance of the product must be carried out by adults only.

• Arrange necessary manpower when assembling or moving the product.

• Some parts may contain sharp edges. Wear protective gloves if necessary.

• Check all nuts and bolts periodically for tightness. When required, tighten them again.

• If the product will not be used for a long period of time (e.g., wintertime), it should be

stored in a clean, dry environment.

• Do not light any ﬁres inside or near the product!

• Do not hang any weights on the frame.

• Retain the original package to store the product.

RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.

2 people

• Do not place the product underneath electrical lines.

• Keep children away during assembly.

• This product contains small parts which can be swallowed by children.

• Keep ﬁngers away from places where they can be pinched or trapped.

1-888-670-6684

If you have questions regarding your product, require warranty assistance,

or have damaged or missing parts, please call our customer service toll-free

helpline. Contact us for assistance; we're here to help.

Please read and understand this manual before any assembly. Before beginning

assembly of product, make sure all parts are present. Compare parts with packaging contents list.

If any part is missing, or if you have any questions, contact the service centre at

1-888-670-6684 (toll free).

Place all parts from the box in a cleared area and position them on the ﬂoor in front of you. Remove

all packing materials and place them back into the box. Do not dispose of the packing materials until

assembly is complete. Read each step carefully before beginning any assembly and make sure you

understand each step.

Needed for assembly:

Table rim -

Table leg -

Glass -

M6x20 Combination bolt and washer -

Hex key -

Requires

Place the table rim (A) on a soft, ﬂat surface. Line up the bolt holes on

the table rim (A) with the corresponding bolt holes on the table leg

(B). Insert M6x20 combination bolt and washer (AA) and lightly

tighten the bolt using the hex key (BB). Do not completely tighten

until all assembly is completed. Repeat the above steps for the

remaining table legs.

Your table is now ready to use.

Requires

Ensure all bolts are securely tightened using the hex key (BB). Turn the table to the

upright position. Carefully place the glass (C) into the table rim (A).

Do not

completely tighten.

• Check all screws and nuts periodically for tightness, tightening them

again as required.

• Disassemble the table in the reverse order of the assembly steps.

• Always disassemble the table completely. A partially disassembled

table is not stable enough to resist wind and bad weather, and therefore

can be damaged and/or cause damage.

• Clean the table with mild soap and water. Rinse thoroughly, and wait

until the table is completely dry before reassembling it.