Whirlpool GW397LXUQ1 Guide d'installation

Marque: Whirlpool

Modèle: GW397LXUQ1

Taper: Guide d'installation

INSTALLATIONINSTRUCTIONS

30" (76.2 CM) SLIDE-INGAS RANGES

INSTRUCTIONSPOUR L'INSTALLATIONDESCUISINIERES

GAZ ENCASTRABLESDE30" (76,2 CM)

TableofContents/Table des mati@res

RANGE SAFETY ............................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 3

Tools and Parts ............................................................................ 3

Location Requirements ................................................................ 3

Electrical Requirements ............................................................... 5

Gas Supply Requirements ........................................................... 5

Countertop Preparation ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 7

Unpack Range .............................................................................. 7

Adjust Leveling Legs .................................................................... 7

Install Anti-Tip Bracket ................................................................. 7

Make Gas Connection ................................................................. 8

Verify Anti-Tip Bracket Location .................................................. 9

Level Range .................................................................................. 9

Electronic Ignition System ........................................................... 9

Replace Oven Racks and Storage Drawer ................................ 11

Complete Installation ................................................................. 11

GAS CONVERSIONS .................................................................... 12

LP Gas Conversion .................................................................... 12

Natural Gas Conversion ............................................................. 15

SECURITI :!:DE LA CUISINII_RE ................................................... lg

EXIGENCES D'INSTALLATION ................................................... 20

Outillage et pieces ...................................................................... 20

Exigences d'emplacement ......................................................... 20

Specifications electriques .......................................................... 22

Specifications de I'alimentation en gaz ..................................... 22

Preparation du plan de travail .................................................... 23

INSTRUCTIONS D'INSTALLATION ............................................. 24

Deballage de la cuisiniere .......................................................... 24

Reglage des pieds de nivellement ............................................. 24

Installation de la bride antibasculement .................................... 24

Raccordement au gaz ................................................................ 25

V@ification de I'emplacement de la bride antibasculement ......26

Reglage de I'aplomb de la cuisiniere ......................................... 26

Syst_me d'allumage electronique .............................................. 27

Reinstallation des grilles du four et du tiroir de remisage .........28

Achever I'installation .................................................................. 28

CONVERSIONS POUR CHANGEMENT DE GAZ ....................... 2g

Conversion pour I'alimentation au propane ............................... 29

Conversion pour I'alimentation au gaz naturel .......................... 32

iMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

Installateur : Remettre les instructions d'installation au proprietaire.

Proprietaire : Conserver les instructions d'installation pour reference ulterieure.

8113P681-60

RANGESAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

I WARNING: If the information in this manual is not followed exactly, a fire or explosion I

may result causing property damage, personal injury or death,

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

m WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

IntheStateofMassachusetts,thefollowinginstallationinstructionsapply:

• Installationsandrepairsmustbeperformedbyaqualifiedorlicensedcontractor,plumber,orgasfitterqualifiedorlicensedby

theStateofMassachusetts.

• Ifusingaballvalve,itshallbeaT-handletype.

• Aflexiblegasconnector,whenused,mustnotexceed3feet.

I__L_ 1 Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Tape measure • Pipe-joint compound

resistant to LP gas

• Phillips screwdriver

• Flat blade screwdriver • 3/16"(4.8 mm) carbide-tipped

masonry drill bit (for

• 1/8"flat blade screwdriver concrete/ceramic floors)

• Level • Noncorrosive leak-detection

solution

• Hand or electric drill

For LP/Natural Gas

• Wrench or pliers Conversions

• Pipe wrench • 1/2"combination wrench

• 1%6"combination wrench • 1A"(6 mm) nut driver

• 1/s"(3.2 mm) drill bit (for • %2" (7 mm) nut driver

wood floors)

• Masking tape

• Marker or pencil

Parts supplied

Check that all parts are included.

• LP/Natural Gas Conversion Kit (taped near left rear leg, inside

storage drawer compartment)

• 4- Burner caps

• 2- Burner grates

• 2- Oven racks

• 2 - #12 x 1%" screws (for mounting anti-tip bracket)

• Anti-tip bracket (taped inside storage drawer)

Anti-tip brackets must be securely mounted to the back wall

or floor. Thickness of flooring may require longer screws to

anchor bracket to subfloor. Longer screws are available from

your local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply, See "Electrical Requirements" and

"Gas Supply Requirements" sections.

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

• It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located behind the storage drawer

on the right-hand side of the oven frame.

• The range should be located for convenient use in the

kitchen.

• Recessed installations must provide complete enclosure of

the sides and rear of the range.

To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

or microwave hood combination that projects horizontally a

minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

• All openings in the wall or floor where range is to be installed

must be sealed.

• Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

• The floor anti-tip bracket must be installed. To install the anti-

tip bracket shipped with the range, see "Install Anti-Tip

Bracket" section.

• Grounded electrical supply is required. See "Electrical

Requirements" section.

• Proper gas supply connection must be available. See "Gas

Supply Requirements" section.

• Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

• Use an insulated pad or W' (0.64 cm) plywood under range if

installing range over carpeting.

IMPORTANT:Toavoiddamagetoyourcabinets,checkwithyour

builderorcabinetsuppliertomakesurethatthematerialsused

willnotdiscolor,delaminateorsustainotherdamage.Thisoven

hasbeendesignedinaccordancewiththerequirementsofUL

andCSAInternationalandcomplieswiththemaximumallowable

woodcabinettemperaturesof194°F(90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the

current standards CAN/CSA-A240-1atest edition, or with local

codes.

Mobile home installations require:

• When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing

the range is adequate as long as it conforms to the standards

listed above.

Product Dimensions

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)

countertop depth, 24" (61.0 cm) base cabinet depth and

36" (91.4 cm) countertop height.

If installing a range hood or microwave hood combination above

the range, follow the range hood or microwave hood combination

installation instructions for dimensional clearances above the

cooktop surface.

Range may be installed with zero clearance to combustible

construction at the rear and on the sides below the cooktop.

A. 303/4"(78. ! cm)

B. 353/4"(90.8 cm) height to underside

of cooktop edge with leveling legs

screwed all the way in*

C. Model/serial number plate (!ocated

behind the storage drawer on the

right-hand side of the oven frame

D. 297/8'' (75.9 cm)

E. 28%6" (71.9 cm) from

handle to back of range**

F. 233/4"(60.3 cm)

countertop notch to rear

of cooktop

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61.0 cm) base cabinet with

25" (63.5 cm) countertop; front of oven door protrudes

21/2'' (6.4 cm) beyond 24" (61.0 cm) base cabinet.

A. !3" (33.0 cm) upper cabinet depth

B. 30" (76.2 cm) min. opening width

C. For minimum clearance to the top of the cooktop, see NOTE.

D. 23V4" (59.1 cm) opening depth

E. 30" (76.2 cm) min. opening width

F. Electrical and gas supply - 5V2" (!4.0 cm) min. from either cabinet,

10" (25.4 cm) max. from floor: Nothing located in shaded area can

extend more than 2_ " (5.7 cm) from back wall or range will not slide

all the way back. Grounded outlet must be flush mounted.

G. Cabinet door or hinge should not extend into cutouL

H. 18" (45.7cm)

/. 3" (7.6 cm) min. clearance from both sides of the range to the side

wall or other combustible materiaL

NOTE: 24" (61.0 cm) minimum when bottom of wood or metal

cabinet is protected by not less than 1/4"(0.64 cm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking

platform and the bottom of an unprotected wood or metal

cabinet.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

IMPORTANT: The range must be electrically grounded in

accordance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70

or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is

required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this range be provided.

• Electronic ignition systems operate within wide voltage limits,

but proper grounding and polarity are necessary. Check that

the outlet provides 120-volt power and is correctly grounded.

• The wiring diagram is located on the back of the storage

drawer in a clear plastic bag.

¢],I]YC_@ ...... ..........

_.,t,_t;}tI)=I l@I ._fI<_%_}?!tLI

Explosion Hazard

Use a new CSA International approved gas supply line.

install a shut-off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest

edition.

IMPORTANT: Leak testing of the range must be conducted

according to the manufacturers instructions.

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

• This range is factory set for use with Natural gas. See "Gas

Conversions" section. The model/serial rating plate located

behind the storage drawer on the right-hand side oven door

frame has information on the types of gas that can be used. If

the types of gas listed do not include the type of gas

available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See "Gas

Conversions" section.

Gas Supply Line

Provide a gas supply line of sA" (1.9 cm) rigid pipe to the

range location. A smaller size pipe on longer runs may result

in insufficient gas supply. Pipe-joint compounds that resist

the action of LP gas must be used. Do not use TEFLON ®t

tape. With LP gas, piping or tubing size can be r/2" (1.3 cm)

minimum. Usually, LP gas suppliers determine the size and

materials used in the system.

Flexible metal appliance connector:

If local codes permit, a new CSA design-certified,

4 to 5 ft (122 to 152.4 cm) long, r/2" (1.3 cm) or

3A"(1.9 cm) I.D., flexible metal appliance connector may

be used for connecting range to the gas supply line.

• A r/2" (1.3 cm) male pipe thread is needed for connection

to the female pipe threads of the inlet to the appliance

pressure regulator.

• Do not kink or damage the flexible metal tubing when

moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the range. The rigid

pipe must be level with the range connection. All strains must

be removed from the supply and fuel lines so range will be

level and in line.

Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the range. It should be in a location that allows

ease of opening and closing. Do not block access to shutoff

valve. The valve is for turning on or shutting off gas to the

range.

A.Gassupply line

B.Shutoff valve"open" position

C. Torange

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural gas:

Minimum pressure: 5" WCP

Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP

Maximum pressure: 14" WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Line pressure testing above 1/2psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures in excess of 1/2psi (3.5 kPa).

Line pressure testing at 1/2psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2psi (3.5 kPa).

The cooktop sides of the slide-in range fit over the cutout edge of

your countertop.

If you have a square finish (flat) countertop and the opening width

is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops must have molded edge

shaved flat %" (1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back %" (1.0 cm) from each

front corner and/or rounded edge flattened.

If countertop opening width is greater than 30" (76.2 cm), adjust

the %" (1.0 cm) dimension.

Countertop must be level. Place level on countertop, first side to

side, then front to back. If countertop is not level, range will not

be level. Range must be level for satisfactory baking conditions.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

INSTALLATIONINSTRUCTIONS

_s_¸__(-_ ©_

lc<s, .......'uJ.....

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. Remove shipping materials, tape and protective film from the

range. Keep cardboard bottom under range.

2. Remove oven racks and parts package from inside oven.

3. Pull storage drawer out completely.

4. Remove and discard cardboard cross support.

A. Storage drawer

B. Cardboard cross support

5. To remove cardboard bottom, place range on its back, take

4 cardboard corners from the carton. Stack one cardboard

corner on top of another. Repeat with the other 2 corners.

Place them lengthwise on the floor behind the range to

support the range when it is laid on its back. f.

6. Using 2 or more people, firmly grasp the range and gently lay

it on its back on the cardboard corners. 2.

7. Pull cardboard bottom firmly to remove.

8. Use an adjustable wrench to loosen the leveling legs.

9. Place cardboard or hardboard in front of range. Using 2 or 3.

more people, stand range back up onto cardboard or

hardboard,

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

If range height adjustment is necessary, use a wrench or

pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range

supported on 2 legs after the range has been placed back to

a standing position.

NOTE: To place range back up into a standing position, put a

sheet of cardboard or hardboard in front of range. Using 2 or

more people, stand range back up onto the cardboard or

hardboard.

Adjust the leveling legs to the correct height. Leveling legs

can be loosened to add up to a maximum of 1" (2.5 cm). A

minimum of 3/_6"(5 mm) is needed to engage the anti-tip

bracket.

NOTE: If height adjustment is made when range is standing,

tilt the range back to adjust the front legs, then tilt forward to

adjust the rear legs.

When the range is at the correct height, check that there is

adequate clearance under the range for the anti-tip bracket.

Before sliding range into its final position, check that the anti-

tip bracket will slide under the range and onto the rear

leveling leg prior to anti-tip bracket installation.

Remove the anti-tip bracket that is taped in the storage

drawer.

Determine which mounting method to use: floor or wall.

If you have a stone or masonry floor you can use the wall

mounting method.

Determine and mark centerline of the cutout space. The

mounting bracket can be installed on either the left side or

right side of the cutout. Position mounting bracket in cutout

so that right (or left) edge of the bracket is 14W' (36.2 cm)

from centerline, as shown.

" "" "'""_4"; .....................................A11_I|_11"||||1

A. Centerline

B. !4V4" (36.2 crn)

Drill two 1/8"(3 mm) holes that correspond to the bracket

holes of the determined mounting method. See below.

ii¸

Floor Mounting

Wall Mounting

A. #12 x 1%" screws

B.Anti-tip bracket

A B

A. #12 x 1%" screws

B.Anti-tip bracket

Using the Phillips screwdriver, mount anti-tip bracket to the

wall or floor with the two #12 x 1%" screws provided.

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the

smaller thread ends of the flexible connector adapters (see B

and G in the following illustration).

2. Attach one adapter to the gas pressure regulator and the

other adapter to the gas shutoff valve. Tighten both adapters.

3. Use a 15/16"combination wrench and an adjustable wrench to

attach the flexible connector to the adapters. Check that

connector is not kinked.

B C

y Y" ," _

H G F

A. Gas pressure regulator

B. Use pipe-joint compound.

C. Adapter (must have V2"male

pipe thread)

D. Flexible connector

E.Manual gas shutoff valve

F V," or 3/4"gas pipe

G. Use pipe-joint compound.

H. Adapter

4. Gas supply pipe must not be more than 10" (25.4 cm) above

the floor.

B /

....... E

A. Gas pressure regulator

B. Adapter

C. Flexible connector

D. Manual shutoff valve

E, 10" (25.4 cm) max. straight pipe

Complete Connection

1. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

Move range close to cabinet opening.

remove cardboard or hardboard from under the range. Using

2 or more people, gently move range into its final position.

Pull storage drawer out completel%

Making sure the anti-tip bracket is installed:

• Look for the anti-tip bracket securely attached to floor or

wall.

• Slide range back so rear range foot is under anti-tip

bracket.

1. Place rack in oven. Place level on rack and check levelness of

range, first side to side; then front to back.

A. Closed valve

B. Open valve

Test all connections by brushing on an approved

noncorrosive leak-detection solution. If bubbles appear, a

leak is indicated. Correct any leak found.

Remove cooktop burner caps and grates from parts

package. Align recess in burner caps with pins in burner

base. Burner caps should be level when properly positioned.

If burner caps are not properly positioned, surface burners

will not light. Place burner grates over burners and caps.

2. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

3. Use wrench to adjust leveling legs up or down until range is

level. Push range back into position.

4. Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Range must be level for satisfactory baking conditions.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

4. Plug into a grounded 3 prong outlet.

Initial lighting and gas flame adjustments

Cooktop and oven burners use pilotless igniters in place of

standing pilots. When the cooktop control knob is turned to the

"LITE" position, the system creates a spark to light the burner.

This sparking continues, as long as the control knob is turned to

"LITE."

When the oven control is turned to the desired setting, a glow bar

igniter heats and ignites the gas.

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the "LITE" position.

The flame should light within 4 seconds. The first time a burner is

lit it may take longer that 4 seconds to light because of air in the

gas line.

If burners do not light properly:

• Turn cooktop control knob to the "OFF" position.

• Check that the range is plugged in and the circuit breaker has

not tripped or the household fuse has not blown.

• Checkthatthegasshutoffvalvesaresettothe"open"

position.

• Checkthatburnercapsareproperlypositionedonburner

bases.

Repeatstart-up.Ifaburnerdoesnotlightatthispoint,turnthe

controlknobsto"Off"andcontactyourdealerorauthorized

servicecompanyforassistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop "low" burner

flame should be a steady blue flame approximately 1A"(0.64 cm)

high.

A _ __-

B _ b-dL_L_JL_Jb-d"

A. Low flame

B. High flame

To adjust standard burners:

The flame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly

underneath the control knob.

If the "low" flame needs to be adjusted:

1. Light 1 burner and turn to lowest setting.

2. Remove the control knob.

Hold the knob stem in the low position using a pair of pliers. Use

an 1/8"(3.0 mm) flat-blade screwdriver to turn the screw located in

the center of the control knob stem until the flame is the proper

size.

Check Operation of Oven Bake Burner

1. Remove the oven rack.

2. Using a Phillips screwdriver, remove the 2 oven bake burner

cover screws.

3. Lift up on rear of oven bake burner cover and remove.

4. Place cover on a protected surface.

A.Oven bake burner cover

B.Oven bake burner cover screws

5. Press BAKE. "BAKE" and "000" will flash in the display.

6. Press PRESETS 0 on the number pad.

7. Press BAKE again.

The igniter used to light the oven bake burner will glow. Once the

igniter is hot the oven bake burner should light. Under certain

conditions it may take up to 60 seconds for it to light.

Adjust Oven Bake Burner Flame (if needed)

1. Remove storage drawer.

2. Remove access panel (2 screws) located on the rear wall,

inside the storage drawer compartment.

3. Check the oven bake burner for proper flame.

This flame should have a 1/2"(1.3 cm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should

be clean and soft in character. No yellow tips, blowing or

lifting of flame should occur.

If the oven bake flame needs to be adjusted, locate the air

shutter near the center rear of the range. Use a flat-blade

screwdriver to loosen the air shutter adjustment screw.

Rotate the air shutter until the proper flame appears. Tighten

air shutter adjustment screw.

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI,"

checking the flame at each setting.

5. Repeat above steps for each burner.

A.Air shutteradjustment screw

B.Air shutter

Press CANCEL when finished.

Reinstall access panel and oven bake burner cover.

Check Operation of Oven Broil Burner

1. Close the oven door.

2. Press the BROIL pad. "BROIL" and "SET" will flash in the

display.

3. Press the PRESETS 0 number pad once to set HI Broil or

twice to set LO Broil.

The igniter used to light the oven bake burner will glow. Once the

igniter is hot the oven bake burner should light. Under certain

conditions it may take up to 60 seconds for it to light.

Adjust Oven Broil Burner Flame (if needed)

Look through oven window to check oven broil burner for proper

flame. This flame should have a 1/2"(1.3 cm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should be

clean and soft in character. No yellow tips, blowing or lifting of

flame should occur

If flame needs to be adjusted:

1. Use a flat-blade screwdriver to loosen the air shutter

adjustment screw on the air shutter located at the rear of the

oven broil burner.

2. Adjust the air shutter as need.

3. Tighten air shutter adjustment screw.

A. Air shutter adjustment screw

B. Air shutter

4. Press CANCEL when finished.

Replace oven racks in oven cavity. Replace storage drawer.

To Replace Storage Drawer:

1. Fit the ends of the drawer glides into the rails in the range.

2. Lift up the front of the drawer and gently push in to the first

stop position.

3. Lift drawer up again and push until drawer is closed.

Co op,..,;,,J!ns'(s o"s

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped,

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See "Level Range."

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by protective shipping

material. Dry thoroughly with a soft cloth. For more

information, see the "Range Care" section of the Use and

Care Guide.

6. Read the Use and Care Guide.

7. Turn on surface burners and oven. See the Use and Care

Guide for specific instruction on range operation.

If range does not operate, check the following:

• Household fuse is intact and tight, or circuit breaker has not

tripped.

• Range is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• See "Troubleshooting" in the Use and Care Guide.

When the range has been on for 5 minutes, check for heat. If

the range is cold, turn off the range and check that the gas

supply line shutoff valve is open.

• Ifthe gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• Ifthe gas supply line shutoff valve is open, press the

CANCEL button on the oven control panel and contact a

qualified technician.

GAS CONVERSIONS

Gas conversions from Natural gas to LP gas or from LP gas to

Natural gas must be done by a qualified installer.

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut-off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

To Convert Gas Pressure Regulator

1. Remove oven racks from inside the oven cavity.

2. Remove the storage drawer. See "Replace Oven Racks and

Storage Drawer" section.

3. Remove the oven door. See "Oven Door" section in the Use

and Care guide for oven door removal instructions.

4. Using a Phillips screwdriver, remove and set aside the 2 oven

bake burner cover screws located at the rear of the oven.

A. Oven bake burner cover

B. Oven bake burner cover screws

5. Lift up and remove oven bake burner cover.

6. Remove the 2 oven bake burner screws and set aside.

7. Swing the oven bake burner to the side and lift it off the oven

orifice and set aside.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

1. Turn manual shutoff valve to the closed position.

2. Unplug range or disconnect power.

..............................................................B

A_J ......... .................C

A. Torange

B.Shutoff valve(closedposition)

C.Gassupply line

A. Oven bake burner screws

B, Oven orifice

Locate the access panel at the rear of the storage drawer

compartment. Using a 1A"(6 mm) nut driver, unscrew the

2 access panel screws. Remove access panel and set aside

along with the 2 screws.

A.Access >anelscrews

Locate gas pressure regulator at the rear of the storage

drawer compartment.

12. Screw the regulator cap securely back into place. Do not

overtighten.

To Convert Oven Bake Burner

1. Locate the oven orifice hood from the front of the range.

2. Using an adjustable wrench, turn the Number 49 Natural gas

oven bake burner orifice hood counterclockwise to remove.

IMPORTANT: Do not remove the gas pressure regulator.

10. Unscrew the regulator cap and remove the plastic cover.

A.Number 49 Naturalgas oven bake burner orifice hood

3. Install the Number .0512 LP gas oven bake burner orifice

hood, turning it clockwise 4 or 5 turns. Do not overtighten.

A. Plastic cover

B. Regulator cap

11. Flip the regulator cap over and replace the plastic cover.

A, Black ,0512 LP orifice hood

//sB

A.Natural gasposition

B.LP gasposition

C.Plastic cover

4= Position the oven bake burner over the oven bake burner

orifice hood and reinstall using 2 screws.

Install the green Number .0430 LP gas oven broil burner

orifice hood, turning it clockwise 4 or 5 turns. Do not

overtighten.

A. Oven bake burner

B. Oven bake burner orifice hood

5. Reinstall access panel and oven bake burner cover.

To Convert Oven Broil Burner

1. Remove oven broil burner screw and set aside.

2. Remove the oven broil burner from the oven broil burner

orifice hood. The oven broil burner will hang in the back of the

oven while changing the orifice hood.

A. Number .0430 LP gas oven broil burner orifice hood

5. Place the oven broil burner on the oven broil burner orifice

hood. Insert the oven broil burner Iocator pin in the hole in the

oven back.

6. Position the oven broil burner against the roof of the oven

cavity and attach with screw.

A B

A.Oven broil burner screw

B.Oven broil burner orifice hood

Turn the Number 52 Natural gas oven broil burner orifice

hood counterclockwise to remove.

A. Oven broil burner orifice hood

B. Oven broil burner

C. Oven broil burner locater pin

D. Oven broil burner locater hole

To Convert Surface Burners

1. If installed, remove the burner grates.

2. Remove the burner caps.

3. Using a Phillips screwdriver, remove the burner base.

A. Number 52 Natural gas oven broil burner orifice hood

A. Burner cap

B. Gas tube opening

C. Burner base screws

D. Burner base

Apply masking tape to the end of a %2" (7,0 mm) nut driver to

help hold the Natural gas orifice spud in the nut driver while

changing it. Press nut driver down onto the Natural gas orifice

spud and remove by turning it counterclockwise and lifting

out. Set the Natural gas orifice spud aside.

A. Natural gas orifice spud

Use the following chart for correct LP gas orifice spud for each

burner, Refer to the model/serial rating plate on the lower right

side of the front frame for proper sizing of LP gas orifice spuds

for each burner location.

LP Gas Orifice Spud Chart

Burner Rating Color Number

5,000 BTU Blue 64L

9,200 BTU Clear 91L

12,500 BTU Green 97L

14,000 BTU Red 114L

15,000 BTU Red 114L

5. Replace the Natural gas orifice spud with the correct LP gas

orifice spud. See the "LP Gas Orifice Spud Chart."

6. Replace burner base and hand tighten the screws,

7. Replace burner cap.

8. Repeat steps 1 through 7 for the remaining burners.

9. Place Natural gas orifice spuds in plastic parts bag for future

use and keep with literature package.

fO. Replace burner grates.

11. Reinstall storage drawer. See the "Replace Oven Racks and

Storage Drawer" section for instructions.

12. Reinstall oven door. See the "Oven Door" section the Use and

Care Guide.

13. Complete installation. See "Make Gas Connection" and

Electronic Ignition System" sections,

Checking for proper cooktop burner flame is very important.

The small inner cone should have a very distinct blue flame

1/4"to _/2"long. The outer cone is not as distinct as the inner

cone. LP gas flames have a slightly yellow tip,

IMPORTANT: You may have to adjust the "LO" setting for

each cooktop burner.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti=tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

f. Turn manual shutoff valve to the closed position.

2. Unplug range or disconnect power.

.............B

A. Torange

B.Shutoff valve(closedposition)

C.Gassupply line

To Convert Gas Pressure Regulator

1. Remove oven racks from inside the oven cavity,

2. Remove the storage drawer. See "Replace Oven Racks and

Storage Drawer" section.

3. Remove the oven door. See "Oven Door" section in the Use

and Care guide for oven door removal instructions.

4. Using a Phillips screwdriver, remove the 2 oven bake burner

cover screws located at the rear of the oven,

A. Oven bake burner cover

B. Oven bake burner cover screws

5. Lift up and remove oven bake burner cover.

6. Remove the 2 oven bake burner screws and set aside.

7. Swing the oven bake burner to the side and lift it off the oven

orifice and set aside.

10. Unscrew the regulator cap and remove the plastic cover.

A. Plastic cover

B. Regulator cap

11. Flip the regulator cap over and replace the plastic cover.

A. Oven bake bumer screws

B. Oven orifice

Locate the access panel at the rear of the storage drawer

compartment. Using a 1A"(6 mm) nut driver, unscrew the

2 access panel screws. Remove access panel and set aside

along with the 2 screws.

A.Access panel screws

Locate gas pressure regulator at the rear of the storage

drawer compartment.

A. LP gas position

B. Natural gas position

C. Plastic cover

12. Screw the regulator cap securely back into place. Do not

overtighten.

To Convert Oven Bake Burner

1. Locate the oven orifice hood from the front of the range.

2. Using an adjustable wrench, turn the Number .0512 LP gas

oven bake burner orifice hood counterclockwise to remove.

IMPORTANT: Do not remove the gas pressure regulator.

A, Number .0512 LP gas oven bake burner orifice hood

3. Install the Number 49 Natural gas oven bake burner orifice 3. Turn the green Number .0430 LP gas oven broil burner orifice

hood, turning it clockwise 4 or 5 turns. Do not overtighten, hood counterclockwise to remove,

A. Number 49 Naturalgas oven bake burner orifice hood

Position the oven bake burner over the oven bake burner

orifice hood and reinstall using 2 screws.

s /

A.Number .0430 LPgas oven broil burner orifice hood

Install the Number 52 Natural gas oven broil burner orifice

hood, turning it clockwise 4 or 5 turns. Do not overtighten.

A. Oven bake burner

B. Oven bake burner orifice hood

5. Reinstall access panel and oven bake burner cover.

To Convert Oven Broil Burner

1. Remove oven broil burner screw and set aside.

2. Remove the oven broil burner from the oven broil burner

orifice hood. The oven broil burner will hang in the back of the

oven while changing the orifice hood.

A ....

A.Oven broil burner screw

B.Oven broil burner orifice hood

A. Number 52 Natural gas oven broil burner orifice hood

5. Place the oven broil burner on the oven broil burner orifice

hood. Insert the oven broil burner Iocator pin in the hole in the

oven back.

6. Position the oven broil burner against the roof of the oven

cavity and attach with screw.

A B

A. Oven broil burner orifice hood

B. Oven broil burner

C. Oven broil burner locater pin

D. Oven broil burner locater hole

To Convert Surface Burners

1. If installed, remove the burner grates.

2. Remove the burner caps.

3. Using a Phillips screwdriver, remove the burner base..

A. Burner cap C. Burner base screws

B. Gas tube opening D. Burner base

Apply masking tape to the end of a %_" (7 mm) nut driver to

help hold the LP gas orifice spud in the nut driver while

changing it. Press nut driver down onto the LP gas orifice

spud and remove by turning it counterclockwise and lifting

out. Set the LP gas orifice spud aside.

A. LP gas orifice spud

Use the following chart for correct Natural gas orifice spud for

each burner. Refer to the model/serial rating plate on the lower

right side of the front frame for proper sizing of Natural orifice

spuds for each burner location.

Natural Gas Orifice Spud Chart

Burner Rating Color Number

5,000 BTU Green 107N

9,200 BTU Clear 142N

12,500 BTU Clear 170N

14,000 BTU Clear 180N

15,000 BTU Black 195N

5. Replace the LP gas orifice spud with correct Natural gas

orifice spud. See the "Natural Gas Orifice Spud Chart."

6. Replace burner base and hand tighten the screws.

7. Replace burner cap.

8. Repeat steps 1 through 7 for the remaining burners.

9. Place LP gas orifice spuds in plastic parts bag for future use

and keep with literature package.

10. Replace burner grates.

11. Reinstall storage drawer. See the "Replace Oven Racks and

Storage Drawer" section for instructions.

12. Reinstall oven door. See the "Oven Door" section the Use and

Care Guide.

13.

Complete installation. See "Make Gas Connection" and

Electronic Ignition System" sections.

Checking for proper cooktop burner flame is very important.

The small inner cone should have a very distinct blue flame

V4"to V2"long. The outer cone is not as distinct as the inner

cone. Natural gas flames do not have yellow tips.

IMPORTANT: You may have to adjust the "LO" setting for each

cooktop burner.

SECURITEDELACUISINIERE

Votre s_curit_ et celle des autres est tres importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tous les messages de securite et de vous y conformer.

Voici le symbole d'alerte de securit6.

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous

et & d'autres.

Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de deces ou de blessure grave si vous ne

suivez pas immediatement lee instructions.

Risque possible de deces ou de blessure grave si vous

ne suivez pas lee instructions.

Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

AVERTISSEMENT : Si les renseignements dans ce manuel ne sont pas exactement

observes, un incendie ou une explosion peut survenir, causant des dommages au

produit, des blessures ou un d_c_s.

- Ne pas entreposer ni utiliser de I'essence ou d'autres vapeurs ou liquides inflammables

proximit_ de cet appareil ou de tout autre appareil _lectrom_nager.

- QUE FAIRE DANS LE CAS D'UNE ODEUR DE GAZ :

• Ne pas tenter d'allumer un appareil.

• Ne pas toucher a un commutateur _lectrique.

• Ne pas utiliser le t_l_phone se trouvant sur les lieux.

• Appeler imm_diatement le fournisseur de gaz d'un t_l_phone voisin. Suivre

ses instructions.

• A d_faut de joindre votre fournisseur de gaz, appeler les pompiers.

- L'installation et I'entretien doivent _tre effectu_s par un installateur qualifi_, une agence

de service ou le fournisseur de gaz.

Risque de basculement

Un enfant ou une personne adulte peut faire basculer la cuisiniere ce qui peut causer un deces.

Joindre la bride antibasculement au pied arriere de la cuisiniere.

Joindre de nouveau la bride antibasculement si la cuisiniere est deplacee.

Le non-respect de ces instructions peut causer un decee ou des brt31ures graves aux enfants et

aux adultes.

EXIGENCESD'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiques ici.

Outillage n_cessaire

• Metre ruban

• Tournevis Phillips

• Tournevis & lame plate

• Tournevis a lame plate

de 1/s"

• Niveau

• Perceuse manuelle ou

electrique

• Cle ou pince

• Cle &tuyauterie

• Cle mixte de15Ae"

• Foret de %" (3,2 mm)

(pour planchers en bois

• Marqueur ou crayon

• Compose d'etancheite des

raccords filetes - resistant au

propane

• Foret a magonnerie a pointe

carburee de

3A6"(4,8 mm) (pour planchers en

beton/ceramique)

• Solution non corrosive de

detection des fuites

Pour les conversions de Propane

gaz naturel

• Cle mixte de 1/2"

• Tourne-ecrou de 1/4"(6,0 mm)

• Tourne-ecrou de %2" (7,0 mm)

• Ruban adhesif de masquage

Pi_ces fournies

Verifier que toutes les pieces sont presentes.

• Ensemble de conversion Propane/gaz naturel (fixe par ruban

adhesif pres du pied arriere gauche a I'interieur du

compartiment du tiroir de remisage)

• 4 chapeaux de brOleur

• 2 grilles de brQleur

• 2 grilles de four

• 2 vis n° 12 x 1%" (pour ie montage de ia bride anti-

basculement)

• Bride anti-basculement (fixee par ruban adhesif dans le tiroir

de remisage)

Les brides anti-basculement doivent _tre fixees au mur

arriere ou au sol. La profondeur du plancher peut necessiter

des vis plus Iongues pour I'ancrage de la bride dans le sous-

plancher. Des vis plus Iongues sont disponibles aupres de

votre quincaillerie locale.

Pi_ces n_cessaires

Verifier les codes iocaux et consulter le fournisseur de gaz.

Verifier I'alimentation en gaz et I'alimentation electrique

existantes. Voir les sections "Specifications electriques" et

"Specifications de i'alimentation en gaz".

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur. Ne pas obstruer le flux de combustion et

la ventilation.

• C'est a I'installateur qu'incombe la responsabilite de

respecter les distances de separation exigees, specifiees sur

la plaque signaletique de I'appareil. La plaque signaletique

est situee sur le c6te droit du ch&ssis du four, derriere le tiroir

de remisage).

• La cuisiniere dolt _tre installee & un endroit pratique dans la

cuisine.

• Dans le cas d'une cuisiniere encastree, I'enceinte dolt

recouvrir completement les c6tes et I'arriere de la cuisiniere.

Afin de supprimer le risque de brQlures ou d'incendie en se

penchant au-dessus des unites de surface chauffees, le

rangement en armoire au-dessus des unites de surface dolt

_tre evit& Si le rangement en placard est n_cessaire, le risque

peut _tre reduit par I'installation d'une hotte de cuisini_re ou

d'un ensemble hotte/micro-ondes operant horizontalement

sur un minimum de 5" (12,7 cm) au-dela du bas des placards.

• Toutes les ouvertures decoupees dans lemur ou le plancher

de I'emplacement d'installation de la cuisiniere doivent _tre

scellees.

• Respecter les dimensions indiquees pour les ouvertures &

decouper dans les placards. Ces dimensions constituent les

valeurs minimales des degagements de separation.

La bride antibasculement de plancher dolt _tre installee. Pour

I'installation de la bride antibasculement exp_diee avec la

cuisiniere, voir la section "Installation de la bride

antibasculement".

• Une source d'electricite avec liaison a la terre est necessaire.

Voir la section "Specifications electriques".

• Une source de gaz adequate dolt _tre disponibie. Voir la

section "Specifications de i'alimentation en gaz".

• Contacter un installateur de rev_tement de sol qualifie, qui

pourra determiner si le rev_tement de sol peut resister a une

temperature d'au moins 200°F (93°C).

• Dans le cas de I'installation de la cuisiniere par dessus un

tapis, placer sous la cuisiniere une plaque d'appui isolee, ou

une plaque de contreplaque de 1A"(0,64 cm).

IMPORTANT" Pour eviter d'endommager les placards, consulter

le constructeur de la maison ou le fabricant des placards pour

determiner si les materiaux utilises peuvent subir un changement

de couleur, une destratification ou d'autres dommages. Ce four a

ete congu conformement aux exigences des normes UL et CSA

International et respecte les temperatures maximales permises

de 194°F (90°C) pour les placards en bois.

La page charge ...

Whirlpool GW397LXUQ1 Guide d'installation

Marque: Whirlpool

Modèle: GW397LXUQ1

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool GW397LXUQ1 Installation guide

Whirlpool GW397LXUQ1 Guide d'installation

Whirlpool GW397LXUQ1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents