Whirlpool GW397LXUT06 Guide d'installation

Taper
Guide d'installation
INSTALLATIONINSTRUCTIONS
30" (76.2 CM) SLIDE-INGAS RANGES
INSTRUCTIONSPOUR L'INSTALLATIONDESCUISINIERES
GAZ ENCASTRABLESDE30" (76,2 CM)
TableofContents/Table des mati@res
RANGE SAFETY ............................................................................. 2
INSTALLATION REQUIREMENTS ................................................ 3
Tools and Parts ............................................................................ 3
Location Requirements ................................................................ 3
Electrical Requirements ............................................................... 5
Gas Supply Requirements ........................................................... 5
Countertop Preparation ............................................................... 6
INSTALLATION INSTRUCTIONS .................................................. 7
Unpack Range .............................................................................. 7
Adjust Leveling Legs .................................................................... 7
Install Anti-Tip Bracket ................................................................. 7
Make Gas Connection ................................................................. 8
Verify Anti-Tip Bracket Location .................................................. 9
Level Range .................................................................................. 9
Electronic Ignition System ........................................................... 9
Replace Oven Racks and Storage Drawer ................................ 11
Complete Installation ................................................................. 11
GAS CONVERSIONS .................................................................... 12
LP Gas Conversion .................................................................... 12
Natural Gas Conversion ............................................................. 15
SECURITI :!:DE LA CUISINII_RE ................................................... lg
EXIGENCES D'INSTALLATION ................................................... 20
Outillage et pieces ...................................................................... 20
Exigences d'emplacement ......................................................... 20
Specifications electriques .......................................................... 22
Specifications de I'alimentation en gaz ..................................... 22
Preparation du plan de travail .................................................... 23
INSTRUCTIONS D'INSTALLATION ............................................. 24
Deballage de la cuisiniere .......................................................... 24
Reglage des pieds de nivellement ............................................. 24
Installation de la bride antibasculement .................................... 24
Raccordement au gaz ................................................................ 25
V@ification de I'emplacement de la bride antibasculement ......26
Reglage de I'aplomb de la cuisiniere ......................................... 26
Syst_me d'allumage electronique .............................................. 27
Reinstallation des grilles du four et du tiroir de remisage .........28
Achever I'installation .................................................................. 28
CONVERSIONS POUR CHANGEMENT DE GAZ ....................... 2g
Conversion pour I'alimentation au propane ............................... 29
Conversion pour I'alimentation au gaz naturel .......................... 32
iMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
iMPORTANT :
Installateur : Remettre les instructions d'installation au proprietaire.
Proprietaire : Conserver les instructions d'installation pour reference ulterieure.
8113P681-60
RANGESAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
I WARNING: If the information in this manual is not followed exactly, a fire or explosion I
I
may result causing property damage, personal injury or death,
I
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
m WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the "What to do if you smell gas" instructions.
IntheStateofMassachusetts,thefollowinginstallationinstructionsapply:
Installationsandrepairsmustbeperformedbyaqualifiedorlicensedcontractor,plumber,orgasfitterqualifiedorlicensedby
theStateofMassachusetts.
Ifusingaballvalve,itshallbeaT-handletype.
Aflexiblegasconnector,whenused,mustnotexceed3feet.
I__L_ 1 Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death or serious burns to children and adults.
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Tape measure Pipe-joint compound
resistant to LP gas
Phillips screwdriver
Flat blade screwdriver 3/16"(4.8 mm) carbide-tipped
masonry drill bit (for
1/8"flat blade screwdriver concrete/ceramic floors)
Level Noncorrosive leak-detection
solution
Hand or electric drill
For LP/Natural Gas
Wrench or pliers Conversions
Pipe wrench 1/2"combination wrench
1%6"combination wrench 1A"(6 mm) nut driver
1/s"(3.2 mm) drill bit (for %2" (7 mm) nut driver
wood floors)
Masking tape
Marker or pencil
Parts supplied
Check that all parts are included.
LP/Natural Gas Conversion Kit (taped near left rear leg, inside
storage drawer compartment)
4- Burner caps
2- Burner grates
2- Oven racks
2 - #12 x 1%" screws (for mounting anti-tip bracket)
Anti-tip bracket (taped inside storage drawer)
Anti-tip brackets must be securely mounted to the back wall
or floor. Thickness of flooring may require longer screws to
anchor bracket to subfloor. Longer screws are available from
your local hardware store.
Parts needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply, See "Electrical Requirements" and
"Gas Supply Requirements" sections.
IMPORTANT: Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
It is the installer's responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located behind the storage drawer
on the right-hand side of the oven frame.
The range should be located for convenient use in the
kitchen.
Recessed installations must provide complete enclosure of
the sides and rear of the range.
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
or microwave hood combination that projects horizontally a
minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
All openings in the wall or floor where range is to be installed
must be sealed.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
The floor anti-tip bracket must be installed. To install the anti-
tip bracket shipped with the range, see "Install Anti-Tip
Bracket" section.
Grounded electrical supply is required. See "Electrical
Requirements" section.
Proper gas supply connection must be available. See "Gas
Supply Requirements" section.
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
Use an insulated pad or W' (0.64 cm) plywood under range if
installing range over carpeting.
IMPORTANT:Toavoiddamagetoyourcabinets,checkwithyour
builderorcabinetsuppliertomakesurethatthematerialsused
willnotdiscolor,delaminateorsustainotherdamage.Thisoven
hasbeendesignedinaccordancewiththerequirementsofUL
andCSAInternationalandcomplieswiththemaximumallowable
woodcabinettemperaturesof194°F(90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-1atest edition, or with local
codes.
Mobile home installations require:
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
Product Dimensions
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
If installing a range hood or microwave hood combination above
the range, follow the range hood or microwave hood combination
installation instructions for dimensional clearances above the
cooktop surface.
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
H
C
D
A. 303/4"(78. ! cm)
B. 353/4"(90.8 cm) height to underside
of cooktop edge with leveling legs
screwed all the way in*
C. Model/serial number plate (!ocated
behind the storage drawer on the
right-hand side of the oven frame
D. 297/8'' (75.9 cm)
E. 28%6" (71.9 cm) from
handle to back of range**
F. 233/4"(60.3 cm)
countertop notch to rear
of cooktop
*Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
**When installed in a 24" (61.0 cm) base cabinet with
25" (63.5 cm) countertop; front of oven door protrudes
21/2'' (6.4 cm) beyond 24" (61.0 cm) base cabinet.
A. !3" (33.0 cm) upper cabinet depth
B. 30" (76.2 cm) min. opening width
C. For minimum clearance to the top of the cooktop, see NOTE.
D. 23V4" (59.1 cm) opening depth
E. 30" (76.2 cm) min. opening width
F. Electrical and gas supply - 5V2" (!4.0 cm) min. from either cabinet,
10" (25.4 cm) max. from floor: Nothing located in shaded area can
extend more than 2_ " (5.7 cm) from back wall or range will not slide
all the way back. Grounded outlet must be flush mounted.
G. Cabinet door or hinge should not extend into cutouL
H. 18" (45.7cm)
/. 3" (7.6 cm) min. clearance from both sides of the range to the side
wall or other combustible materiaL
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is protected by not less than 1/4"(0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an unprotected wood or metal
cabinet.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT: The range must be electrically grounded in
accordance with local codes and ordinances, or in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70
or Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is
required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit
serving only this range be provided.
Electronic ignition systems operate within wide voltage limits,
but proper grounding and polarity are necessary. Check that
the outlet provides 120-volt power and is correctly grounded.
The wiring diagram is located on the back of the storage
drawer in a clear plastic bag.
¢],I]YC_@ ...... ..........
_.,t,_t;}tI)=I l@I ._fI<_%_}?!tLI
Explosion Hazard
Use a new CSA International approved gas supply line.
install a shut-off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas
Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest
edition.
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturers instructions.
Type of Gas
Natural gas:
This range is design-certified by CSA International for use with
Natural gas or, after proper conversion, for use with LP gas.
This range is factory set for use with Natural gas. See "Gas
Conversions" section. The model/serial rating plate located
behind the storage drawer on the right-hand side oven door
frame has information on the types of gas that can be used. If
the types of gas listed do not include the type of gas
available, check with the local gas supplier.
LP gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier. See "Gas
Conversions" section.
Gas Supply Line
Provide a gas supply line of sA" (1.9 cm) rigid pipe to the
range location. A smaller size pipe on longer runs may result
in insufficient gas supply. Pipe-joint compounds that resist
the action of LP gas must be used. Do not use TEFLON ®t
tape. With LP gas, piping or tubing size can be r/2" (1.3 cm)
minimum. Usually, LP gas suppliers determine the size and
materials used in the system.
Flexible metal appliance connector:
If local codes permit, a new CSA design-certified,
4 to 5 ft (122 to 152.4 cm) long, r/2" (1.3 cm) or
3A"(1.9 cm) I.D., flexible metal appliance connector may
be used for connecting range to the gas supply line.
A r/2" (1.3 cm) male pipe thread is needed for connection
to the female pipe threads of the inlet to the appliance
pressure regulator.
Do not kink or damage the flexible metal tubing when
moving the range.
Rigid pipe connection:
The rigid pipe connection requires a combination of pipe
fittings to obtain an in-line connection to the range. The rigid
pipe must be level with the range connection. All strains must
be removed from the supply and fuel lines so range will be
level and in line.
Must include a shutoff valve:
The supply line must be equipped with a manual shutoff
valve. This valve should be located in the same room but
external to the range. It should be in a location that allows
ease of opening and closing. Do not block access to shutoff
valve. The valve is for turning on or shutting off gas to the
range.
B
c'
A.Gassupply line
B.Shutoff valve"open" position
C. Torange
Gas Pressure Regulator
The gas pressure regulator supplied with this range must be
used. The inlet pressure to the regulator should be as follows for
proper operation:
Natural gas:
Minimum pressure: 5" WCP
Maximum pressure: 14" WCP
LP gas:
Minimum pressure: 11" WCP
Maximum pressure: 14" WCP
Contact local gas supplier if you are not sure about the inlet
pressure.
Burner Input Requirements
Input ratings shown on the model/serial rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at a
rate of 4% for each 1,000 ft (304.8 m) above sea level (not
applicable for Canada).
Gas Supply Pressure Testing
Line pressure testing above 1/2psi gauge (14" WCP)
The range and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2psi (3.5 kPa).
Line pressure testing at 1/2psi gauge (14" WCP) or lower
The range must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to
or less than 1/2psi (3.5 kPa).
The cooktop sides of the slide-in range fit over the cutout edge of
your countertop.
If you have a square finish (flat) countertop and the opening width
is 30" (76.2 cm), no countertop preparation is required.
Formed front-edged countertops must have molded edge
shaved flat %" (1.0 cm) from each front corner of opening.
Tile countertops may need trim cut back %" (1.0 cm) from each
front corner and/or rounded edge flattened.
If countertop opening width is greater than 30" (76.2 cm), adjust
the %" (1.0 cm) dimension.
Countertop must be level. Place level on countertop, first side to
side, then front to back. If countertop is not level, range will not
be level. Range must be level for satisfactory baking conditions.
1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
INSTALLATIONINSTRUCTIONS
_s_¸__(-_ ©_
lc<s, .......'uJ.....
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
1. Remove shipping materials, tape and protective film from the
range. Keep cardboard bottom under range.
2. Remove oven racks and parts package from inside oven.
3. Pull storage drawer out completely.
4. Remove and discard cardboard cross support.
A
B
A. Storage drawer
B. Cardboard cross support
2=
3=
5. To remove cardboard bottom, place range on its back, take
4 cardboard corners from the carton. Stack one cardboard
corner on top of another. Repeat with the other 2 corners.
Place them lengthwise on the floor behind the range to
support the range when it is laid on its back. f.
6. Using 2 or more people, firmly grasp the range and gently lay
it on its back on the cardboard corners. 2.
7. Pull cardboard bottom firmly to remove.
8. Use an adjustable wrench to loosen the leveling legs.
9. Place cardboard or hardboard in front of range. Using 2 or 3.
more people, stand range back up onto cardboard or
hardboard,
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
If range height adjustment is necessary, use a wrench or
pliers to loosen the 4 leveling legs.
This may be done with the range on its back or with the range
supported on 2 legs after the range has been placed back to
a standing position.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard in front of range. Using 2 or
more people, stand range back up onto the cardboard or
hardboard.
Adjust the leveling legs to the correct height. Leveling legs
can be loosened to add up to a maximum of 1" (2.5 cm). A
minimum of 3/_6"(5 mm) is needed to engage the anti-tip
bracket.
NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, then tilt forward to
adjust the rear legs.
When the range is at the correct height, check that there is
adequate clearance under the range for the anti-tip bracket.
Before sliding range into its final position, check that the anti-
tip bracket will slide under the range and onto the rear
leveling leg prior to anti-tip bracket installation.
Remove the anti-tip bracket that is taped in the storage
drawer.
Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor you can use the wall
mounting method.
Determine and mark centerline of the cutout space. The
mounting bracket can be installed on either the left side or
right side of the cutout. Position mounting bracket in cutout
so that right (or left) edge of the bracket is 14W' (36.2 cm)
from centerline, as shown.
" "" "'""_4"; .....................................A11_I|_11"||||1
A. Centerline
B. !4V4" (36.2 crn)
4=
Drill two 1/8"(3 mm) holes that correspond to the bracket
holes of the determined mounting method. See below.
A
ii¸
I
I
I
I
I
Floor Mounting
B
Wall Mounting
A. #12 x 1%" screws
B.Anti-tip bracket
A B
5=
A. #12 x 1%" screws
B.Anti-tip bracket
Using the Phillips screwdriver, mount anti-tip bracket to the
wall or floor with the two #12 x 1%" screws provided.
Explosion Hazard
Use a new CSA international approved gas supply line.
install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Typical flexible connection
1. Apply pipe-joint compound made for use with LP gas to the
smaller thread ends of the flexible connector adapters (see B
and G in the following illustration).
2. Attach one adapter to the gas pressure regulator and the
other adapter to the gas shutoff valve. Tighten both adapters.
3. Use a 15/16"combination wrench and an adjustable wrench to
attach the flexible connector to the adapters. Check that
connector is not kinked.
A
J
B C
/
o
D
E
y Y" ," _
H G F
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have V2"male
pipe thread)
D. Flexible connector
E.Manual gas shutoff valve
F V," or 3/4"gas pipe
G. Use pipe-joint compound.
H. Adapter
4. Gas supply pipe must not be more than 10" (25.4 cm) above
the floor.
A
B /
C
....... E
D
A. Gas pressure regulator
B. Adapter
C. Flexible connector
D. Manual shutoff valve
E, 10" (25.4 cm) max. straight pipe
Complete Connection
1. Open the manual shutoff valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
1.
2.
3.
4.
Move range close to cabinet opening.
remove cardboard or hardboard from under the range. Using
2 or more people, gently move range into its final position.
Pull storage drawer out completel%
Making sure the anti-tip bracket is installed:
Look for the anti-tip bracket securely attached to floor or
wall.
Slide range back so rear range foot is under anti-tip
bracket.
1. Place rack in oven. Place level on rack and check levelness of
range, first side to side; then front to back.
2.
3.
A. Closed valve
B. Open valve
Test all connections by brushing on an approved
noncorrosive leak-detection solution. If bubbles appear, a
leak is indicated. Correct any leak found.
Remove cooktop burner caps and grates from parts
package. Align recess in burner caps with pins in burner
base. Burner caps should be level when properly positioned.
If burner caps are not properly positioned, surface burners
will not light. Place burner grates over burners and caps.
2. If range is not level, pull range forward until rear leveling leg is
removed from the anti-tip bracket.
3. Use wrench to adjust leveling legs up or down until range is
level. Push range back into position.
4. Check that rear leveling leg is engaged in anti-tip bracket.
NOTE: Range must be level for satisfactory baking conditions.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord,
Failure to follow these instructions can result in death,
fire, or electrical shock.
4. Plug into a grounded 3 prong outlet.
Initial lighting and gas flame adjustments
Cooktop and oven burners use pilotless igniters in place of
standing pilots. When the cooktop control knob is turned to the
"LITE" position, the system creates a spark to light the burner.
This sparking continues, as long as the control knob is turned to
"LITE."
When the oven control is turned to the desired setting, a glow bar
igniter heats and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the "LITE" position.
The flame should light within 4 seconds. The first time a burner is
lit it may take longer that 4 seconds to light because of air in the
gas line.
If burners do not light properly:
Turn cooktop control knob to the "OFF" position.
Check that the range is plugged in and the circuit breaker has
not tripped or the household fuse has not blown.
Checkthatthegasshutoffvalvesaresettothe"open"
position.
Checkthatburnercapsareproperlypositionedonburner
bases.
Repeatstart-up.Ifaburnerdoesnotlightatthispoint,turnthe
controlknobsto"Off"andcontactyourdealerorauthorized
servicecompanyforassistance.
Adjust Flame Height
Adjust the height of top burner flames. The cooktop "low" burner
flame should be a steady blue flame approximately 1A"(0.64 cm)
high.
A _ __-
/
B _ b-dL_L_JL_Jb-d"
/
A. Low flame
B. High flame
To adjust standard burners:
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
If the "low" flame needs to be adjusted:
1. Light 1 burner and turn to lowest setting.
2. Remove the control knob.
Hold the knob stem in the low position using a pair of pliers. Use
an 1/8"(3.0 mm) flat-blade screwdriver to turn the screw located in
the center of the control knob stem until the flame is the proper
size.
Check Operation of Oven Bake Burner
1. Remove the oven rack.
2. Using a Phillips screwdriver, remove the 2 oven bake burner
cover screws.
3. Lift up on rear of oven bake burner cover and remove.
4. Place cover on a protected surface.
A.Oven bake burner cover
B.Oven bake burner cover screws
5. Press BAKE. "BAKE" and "000" will flash in the display.
6. Press PRESETS 0 on the number pad.
7. Press BAKE again.
The igniter used to light the oven bake burner will glow. Once the
igniter is hot the oven bake burner should light. Under certain
conditions it may take up to 60 seconds for it to light.
Adjust Oven Bake Burner Flame (if needed)
1. Remove storage drawer.
2. Remove access panel (2 screws) located on the rear wall,
inside the storage drawer compartment.
3. Check the oven bake burner for proper flame.
This flame should have a 1/2"(1.3 cm) long inner cone of
bluish-green, with an outer mantle of dark blue, and should
be clean and soft in character. No yellow tips, blowing or
lifting of flame should occur.
4.
If the oven bake flame needs to be adjusted, locate the air
shutter near the center rear of the range. Use a flat-blade
screwdriver to loosen the air shutter adjustment screw.
Rotate the air shutter until the proper flame appears. Tighten
air shutter adjustment screw.
3. Replace the control knob.
4. Test the flame by turning the control from "LO" to "HI,"
checking the flame at each setting.
5. Repeat above steps for each burner.
5.
6.
B
o_
A.Air shutteradjustment screw
B.Air shutter
Press CANCEL when finished.
Reinstall access panel and oven bake burner cover.
10
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press the BROIL pad. "BROIL" and "SET" will flash in the
display.
3. Press the PRESETS 0 number pad once to set HI Broil or
twice to set LO Broil.
The igniter used to light the oven bake burner will glow. Once the
igniter is hot the oven bake burner should light. Under certain
conditions it may take up to 60 seconds for it to light.
Adjust Oven Broil Burner Flame (if needed)
Look through oven window to check oven broil burner for proper
flame. This flame should have a 1/2"(1.3 cm) long inner cone of
bluish-green, with an outer mantle of dark blue, and should be
clean and soft in character. No yellow tips, blowing or lifting of
flame should occur
If flame needs to be adjusted:
1. Use a flat-blade screwdriver to loosen the air shutter
adjustment screw on the air shutter located at the rear of the
oven broil burner.
2. Adjust the air shutter as need.
3. Tighten air shutter adjustment screw.
A. Air shutter adjustment screw
B. Air shutter
4. Press CANCEL when finished.
Replace oven racks in oven cavity. Replace storage drawer.
To Replace Storage Drawer:
1. Fit the ends of the drawer glides into the rails in the range.
2. Lift up the front of the drawer and gently push in to the first
stop position.
3. Lift drawer up again and push until drawer is closed.
Co op,..,;,,J!ns'(s o"s
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped,
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check that the range is level. See "Level Range."
5. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by protective shipping
material. Dry thoroughly with a soft cloth. For more
information, see the "Range Care" section of the Use and
Care Guide.
6. Read the Use and Care Guide.
7. Turn on surface burners and oven. See the Use and Care
Guide for specific instruction on range operation.
If range does not operate, check the following:
Household fuse is intact and tight, or circuit breaker has not
tripped.
Range is plugged into a grounded 3 prong outlet.
Electrical supply is connected.
See "Troubleshooting" in the Use and Care Guide.
8=
When the range has been on for 5 minutes, check for heat. If
the range is cold, turn off the range and check that the gas
supply line shutoff valve is open.
Ifthe gas supply line shutoff valve is closed, open it, then
repeat the 5-minute test as outlined above.
Ifthe gas supply line shutoff valve is open, press the
CANCEL button on the oven control panel and contact a
qualified technician.
11
GAS CONVERSIONS
Gas conversions from Natural gas to LP gas or from LP gas to
Natural gas must be done by a qualified installer.
Explosion Hazard
Use a new CSA international approved gas supply line.
install a shut-off valve.
Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
To Convert Gas Pressure Regulator
1. Remove oven racks from inside the oven cavity.
2. Remove the storage drawer. See "Replace Oven Racks and
Storage Drawer" section.
3. Remove the oven door. See "Oven Door" section in the Use
and Care guide for oven door removal instructions.
4. Using a Phillips screwdriver, remove and set aside the 2 oven
bake burner cover screws located at the rear of the oven.
A
A. Oven bake burner cover
B. Oven bake burner cover screws
5. Lift up and remove oven bake burner cover.
6. Remove the 2 oven bake burner screws and set aside.
7. Swing the oven bake burner to the side and lift it off the oven
orifice and set aside.
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
1. Turn manual shutoff valve to the closed position.
2. Unplug range or disconnect power.
..............................................................B
A_J ......... .................C
A. Torange
B.Shutoff valve(closedposition)
C.Gassupply line
/
A. Oven bake burner screws
B, Oven orifice
12
8=
9=
Locate the access panel at the rear of the storage drawer
compartment. Using a 1A"(6 mm) nut driver, unscrew the
2 access panel screws. Remove access panel and set aside
along with the 2 screws.
A
A.Access >anelscrews
Locate gas pressure regulator at the rear of the storage
drawer compartment.
12. Screw the regulator cap securely back into place. Do not
overtighten.
To Convert Oven Bake Burner
1. Locate the oven orifice hood from the front of the range.
2. Using an adjustable wrench, turn the Number 49 Natural gas
oven bake burner orifice hood counterclockwise to remove.
IMPORTANT: Do not remove the gas pressure regulator.
10. Unscrew the regulator cap and remove the plastic cover.
A.Number 49 Naturalgas oven bake burner orifice hood
3. Install the Number .0512 LP gas oven bake burner orifice
hood, turning it clockwise 4 or 5 turns. Do not overtighten.
A. Plastic cover
B. Regulator cap
11. Flip the regulator cap over and replace the plastic cover.
A, Black ,0512 LP orifice hood
//sB
1@
A.Natural gasposition
B.LP gasposition
C.Plastic cover
13
4= Position the oven bake burner over the oven bake burner
orifice hood and reinstall using 2 screws.
A
f
_B
4=
Install the green Number .0430 LP gas oven broil burner
orifice hood, turning it clockwise 4 or 5 turns. Do not
overtighten.
A. Oven bake burner
B. Oven bake burner orifice hood
5. Reinstall access panel and oven bake burner cover.
To Convert Oven Broil Burner
1. Remove oven broil burner screw and set aside.
2. Remove the oven broil burner from the oven broil burner
orifice hood. The oven broil burner will hang in the back of the
oven while changing the orifice hood.
A. Number .0430 LP gas oven broil burner orifice hood
5. Place the oven broil burner on the oven broil burner orifice
hood. Insert the oven broil burner Iocator pin in the hole in the
oven back.
6. Position the oven broil burner against the roof of the oven
cavity and attach with screw.
A B
C
D
3=
_B
A.Oven broil burner screw
B.Oven broil burner orifice hood
Turn the Number 52 Natural gas oven broil burner orifice
hood counterclockwise to remove.
A. Oven broil burner orifice hood
B. Oven broil burner
C. Oven broil burner locater pin
D. Oven broil burner locater hole
To Convert Surface Burners
1. If installed, remove the burner grates.
2. Remove the burner caps.
3. Using a Phillips screwdriver, remove the burner base.
A. Number 52 Natural gas oven broil burner orifice hood
A. Burner cap
B. Gas tube opening
C. Burner base screws
D. Burner base
14
4,
Apply masking tape to the end of a %2" (7,0 mm) nut driver to
help hold the Natural gas orifice spud in the nut driver while
changing it. Press nut driver down onto the Natural gas orifice
spud and remove by turning it counterclockwise and lifting
out. Set the Natural gas orifice spud aside.
A. Natural gas orifice spud
Use the following chart for correct LP gas orifice spud for each
burner, Refer to the model/serial rating plate on the lower right
side of the front frame for proper sizing of LP gas orifice spuds
for each burner location.
LP Gas Orifice Spud Chart
Burner Rating Color Number
5,000 BTU Blue 64L
9,200 BTU Clear 91L
12,500 BTU Green 97L
14,000 BTU Red 114L
15,000 BTU Red 114L
5. Replace the Natural gas orifice spud with the correct LP gas
orifice spud. See the "LP Gas Orifice Spud Chart."
6. Replace burner base and hand tighten the screws,
7. Replace burner cap.
8. Repeat steps 1 through 7 for the remaining burners.
9. Place Natural gas orifice spuds in plastic parts bag for future
use and keep with literature package.
fO. Replace burner grates.
11. Reinstall storage drawer. See the "Replace Oven Racks and
Storage Drawer" section for instructions.
12. Reinstall oven door. See the "Oven Door" section the Use and
Care Guide.
13. Complete installation. See "Make Gas Connection" and
Electronic Ignition System" sections,
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
1/4"to _/2"long. The outer cone is not as distinct as the inner
cone. LP gas flames have a slightly yellow tip,
IMPORTANT: You may have to adjust the "LO" setting for
each cooktop burner.
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti=tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death
or serious burns to children and adults.
f. Turn manual shutoff valve to the closed position.
2. Unplug range or disconnect power.
.............B
A. Torange
B.Shutoff valve(closedposition)
C.Gassupply line
To Convert Gas Pressure Regulator
1. Remove oven racks from inside the oven cavity,
2. Remove the storage drawer. See "Replace Oven Racks and
Storage Drawer" section.
3. Remove the oven door. See "Oven Door" section in the Use
and Care guide for oven door removal instructions.
4. Using a Phillips screwdriver, remove the 2 oven bake burner
cover screws located at the rear of the oven,
A
A. Oven bake burner cover
B. Oven bake burner cover screws
15
5. Lift up and remove oven bake burner cover.
6. Remove the 2 oven bake burner screws and set aside.
7. Swing the oven bake burner to the side and lift it off the oven
orifice and set aside.
10. Unscrew the regulator cap and remove the plastic cover.
A. Plastic cover
B. Regulator cap
11. Flip the regulator cap over and replace the plastic cover.
8=
9=
A. Oven bake bumer screws
B. Oven orifice
Locate the access panel at the rear of the storage drawer
compartment. Using a 1A"(6 mm) nut driver, unscrew the
2 access panel screws. Remove access panel and set aside
along with the 2 screws.
A
A.Access panel screws
Locate gas pressure regulator at the rear of the storage
drawer compartment.
B
A. LP gas position
B. Natural gas position
C. Plastic cover
12. Screw the regulator cap securely back into place. Do not
overtighten.
To Convert Oven Bake Burner
1. Locate the oven orifice hood from the front of the range.
2. Using an adjustable wrench, turn the Number .0512 LP gas
oven bake burner orifice hood counterclockwise to remove.
IMPORTANT: Do not remove the gas pressure regulator.
© ©
A, Number .0512 LP gas oven bake burner orifice hood
16
3. Install the Number 49 Natural gas oven bake burner orifice 3. Turn the green Number .0430 LP gas oven broil burner orifice
hood, turning it clockwise 4 or 5 turns. Do not overtighten, hood counterclockwise to remove,
4.
A. Number 49 Naturalgas oven bake burner orifice hood
Position the oven bake burner over the oven bake burner
orifice hood and reinstall using 2 screws.
A
B
s /
4.
A.Number .0430 LPgas oven broil burner orifice hood
Install the Number 52 Natural gas oven broil burner orifice
hood, turning it clockwise 4 or 5 turns. Do not overtighten.
A. Oven bake burner
B. Oven bake burner orifice hood
5. Reinstall access panel and oven bake burner cover.
To Convert Oven Broil Burner
1. Remove oven broil burner screw and set aside.
2. Remove the oven broil burner from the oven broil burner
orifice hood. The oven broil burner will hang in the back of the
oven while changing the orifice hood.
A ....
A.Oven broil burner screw
B.Oven broil burner orifice hood
A. Number 52 Natural gas oven broil burner orifice hood
5. Place the oven broil burner on the oven broil burner orifice
hood. Insert the oven broil burner Iocator pin in the hole in the
oven back.
6. Position the oven broil burner against the roof of the oven
cavity and attach with screw.
A B
A. Oven broil burner orifice hood
B. Oven broil burner
C. Oven broil burner locater pin
D. Oven broil burner locater hole
17
To Convert Surface Burners
1. If installed, remove the burner grates.
2. Remove the burner caps.
3. Using a Phillips screwdriver, remove the burner base..
4.
A. Burner cap C. Burner base screws
B. Gas tube opening D. Burner base
Apply masking tape to the end of a %_" (7 mm) nut driver to
help hold the LP gas orifice spud in the nut driver while
changing it. Press nut driver down onto the LP gas orifice
spud and remove by turning it counterclockwise and lifting
out. Set the LP gas orifice spud aside.
A
A. LP gas orifice spud
Use the following chart for correct Natural gas orifice spud for
each burner. Refer to the model/serial rating plate on the lower
right side of the front frame for proper sizing of Natural orifice
spuds for each burner location.
Natural Gas Orifice Spud Chart
Burner Rating Color Number
5,000 BTU Green 107N
9,200 BTU Clear 142N
12,500 BTU Clear 170N
14,000 BTU Clear 180N
15,000 BTU Black 195N
5. Replace the LP gas orifice spud with correct Natural gas
orifice spud. See the "Natural Gas Orifice Spud Chart."
6. Replace burner base and hand tighten the screws.
7. Replace burner cap.
8. Repeat steps 1 through 7 for the remaining burners.
9. Place LP gas orifice spuds in plastic parts bag for future use
and keep with literature package.
10. Replace burner grates.
11. Reinstall storage drawer. See the "Replace Oven Racks and
Storage Drawer" section for instructions.
12. Reinstall oven door. See the "Oven Door" section the Use and
Care Guide.
13.
Complete installation. See "Make Gas Connection" and
Electronic Ignition System" sections.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
V4"to V2"long. The outer cone is not as distinct as the inner
cone. Natural gas flames do not have yellow tips.
IMPORTANT: You may have to adjust the "LO" setting for each
cooktop burner.
18
SECURITEDELACUISINIERE
Votre s_curit_ et celle des autres est tres importante.
Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de
toujours lire tous les messages de securite et de vous y conformer.
Voici le symbole d'alerte de securit6.
Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous
et & d'autres.
Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de deces ou de blessure grave si vous ne
suivez pas immediatement lee instructions.
Risque possible de deces ou de blessure grave si vous
ne suivez pas lee instructions.
Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
AVERTISSEMENT : Si les renseignements dans ce manuel ne sont pas exactement
observes, un incendie ou une explosion peut survenir, causant des dommages au
produit, des blessures ou un d_c_s.
- Ne pas entreposer ni utiliser de I'essence ou d'autres vapeurs ou liquides inflammables
proximit_ de cet appareil ou de tout autre appareil _lectrom_nager.
- QUE FAIRE DANS LE CAS D'UNE ODEUR DE GAZ :
Ne pas tenter d'allumer un appareil.
Ne pas toucher a un commutateur _lectrique.
Ne pas utiliser le t_l_phone se trouvant sur les lieux.
Appeler imm_diatement le fournisseur de gaz d'un t_l_phone voisin. Suivre
ses instructions.
A d_faut de joindre votre fournisseur de gaz, appeler les pompiers.
- L'installation et I'entretien doivent _tre effectu_s par un installateur qualifi_, une agence
de service ou le fournisseur de gaz.
Risque de basculement
Un enfant ou une personne adulte peut faire basculer la cuisiniere ce qui peut causer un deces.
Joindre la bride antibasculement au pied arriere de la cuisiniere.
Joindre de nouveau la bride antibasculement si la cuisiniere est deplacee.
Le non-respect de ces instructions peut causer un decee ou des brt31ures graves aux enfants et
aux adultes.
19
EXIGENCESD'INSTALLATION
Rassembler les outils et pieces necessaires avant de commencer
I'installation. Lire et suivre les instructions fournies avec les outils
indiques ici.
Outillage n_cessaire
Metre ruban
Tournevis Phillips
Tournevis & lame plate
Tournevis a lame plate
de 1/s"
Niveau
Perceuse manuelle ou
electrique
Cle ou pince
Cle &tuyauterie
Cle mixte de15Ae"
Foret de %" (3,2 mm)
(pour planchers en bois
Marqueur ou crayon
Compose d'etancheite des
raccords filetes - resistant au
propane
Foret a magonnerie a pointe
carburee de
3A6"(4,8 mm) (pour planchers en
beton/ceramique)
Solution non corrosive de
detection des fuites
Pour les conversions de Propane
gaz naturel
Cle mixte de 1/2"
Tourne-ecrou de 1/4"(6,0 mm)
Tourne-ecrou de %2" (7,0 mm)
Ruban adhesif de masquage
Pi_ces fournies
Verifier que toutes les pieces sont presentes.
Ensemble de conversion Propane/gaz naturel (fixe par ruban
adhesif pres du pied arriere gauche a I'interieur du
compartiment du tiroir de remisage)
4 chapeaux de brOleur
2 grilles de brQleur
2 grilles de four
2 vis n° 12 x 1%" (pour ie montage de ia bride anti-
basculement)
Bride anti-basculement (fixee par ruban adhesif dans le tiroir
de remisage)
Les brides anti-basculement doivent _tre fixees au mur
arriere ou au sol. La profondeur du plancher peut necessiter
des vis plus Iongues pour I'ancrage de la bride dans le sous-
plancher. Des vis plus Iongues sont disponibles aupres de
votre quincaillerie locale.
Pi_ces n_cessaires
Verifier les codes iocaux et consulter le fournisseur de gaz.
Verifier I'alimentation en gaz et I'alimentation electrique
existantes. Voir les sections "Specifications electriques" et
"Specifications de i'alimentation en gaz".
IMPORTANT : Observer les dispositions de tousles codes et
reglements en vigueur. Ne pas obstruer le flux de combustion et
la ventilation.
C'est a I'installateur qu'incombe la responsabilite de
respecter les distances de separation exigees, specifiees sur
la plaque signaletique de I'appareil. La plaque signaletique
est situee sur le c6te droit du ch&ssis du four, derriere le tiroir
de remisage).
La cuisiniere dolt _tre installee & un endroit pratique dans la
cuisine.
Dans le cas d'une cuisiniere encastree, I'enceinte dolt
recouvrir completement les c6tes et I'arriere de la cuisiniere.
Afin de supprimer le risque de brQlures ou d'incendie en se
penchant au-dessus des unites de surface chauffees, le
rangement en armoire au-dessus des unites de surface dolt
_tre evit& Si le rangement en placard est n_cessaire, le risque
peut _tre reduit par I'installation d'une hotte de cuisini_re ou
d'un ensemble hotte/micro-ondes operant horizontalement
sur un minimum de 5" (12,7 cm) au-dela du bas des placards.
Toutes les ouvertures decoupees dans lemur ou le plancher
de I'emplacement d'installation de la cuisiniere doivent _tre
scellees.
Respecter les dimensions indiquees pour les ouvertures &
decouper dans les placards. Ces dimensions constituent les
valeurs minimales des degagements de separation.
La bride antibasculement de plancher dolt _tre installee. Pour
I'installation de la bride antibasculement exp_diee avec la
cuisiniere, voir la section "Installation de la bride
antibasculement".
Une source d'electricite avec liaison a la terre est necessaire.
Voir la section "Specifications electriques".
Une source de gaz adequate dolt _tre disponibie. Voir la
section "Specifications de i'alimentation en gaz".
Contacter un installateur de rev_tement de sol qualifie, qui
pourra determiner si le rev_tement de sol peut resister a une
temperature d'au moins 200°F (93°C).
Dans le cas de I'installation de la cuisiniere par dessus un
tapis, placer sous la cuisiniere une plaque d'appui isolee, ou
une plaque de contreplaque de 1A"(0,64 cm).
IMPORTANT" Pour eviter d'endommager les placards, consulter
le constructeur de la maison ou le fabricant des placards pour
determiner si les materiaux utilises peuvent subir un changement
de couleur, une destratification ou d'autres dommages. Ce four a
ete congu conformement aux exigences des normes UL et CSA
International et respecte les temperatures maximales permises
de 194°F (90°C) pour les placards en bois.
2O
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Whirlpool GW397LXUT06 Guide d'installation

Taper
Guide d'installation

dans d''autres langues